TAPE | Revchem Composites

35TP82B_TDS.pdf

Sat, 27 Sep 2025 10:05:26 +0000

Sharpest possible paint lines
Conformability to stretch and adhere
around sharp curves
Flexible backing for easily creating
curved paint edges
Resists edge lifting
Line sharpness
and removal the
way you want.
Fine Line
Masking Tapes
Tapes that keep paint lines sharp, even
on curves and challenging surfaces.

For more information on Scotch

Masking Tapes, contact your local 3M representative or call 1-800-362-3550.
3M Closure and Masking
Systems Division
3M Center, Building 225-3S-06
St. Paul, MN 55144-1000
800-362-3550 877-369-2923 (Fax)
3M.com/masking
3M, the Plaid and Scotch are marks and/or registered marks of 3M. Unauthorized use prohibited.
3M 2020. All rights reserved. Please recycle. 70-0717-0960-7
Warranty and Limited Remedy: 3M warrants that each 3M product meets the applicable 3M product
specification at the time 3M ships the product. 3M MAKES NO OTHER EXPRESS OR IMPLIED WARRANTIES
OR CONDITIONS, INCLUDING ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE. If a 3M product does not conform to this warranty, the sole
and exclusive remedy is, at 3M s option, replacement of the 3M product or refund of the purchase price.
Limitation of Liability: Except for the limited remedy above, and except to the extent prohibited by law, 3M
will not be liable for any loss or damage arising from or related to the 3M product, whether direct, indirect,
special, incidental, or consequential, regardless of the legal or equitable theory asserted.
Scotch

Fine Line Tape Family
Adhesive
Backing
Adhesion to
Steel oz/in
(N/100 mm)
Tensile
Strength
lb/in
(N/100 mm)
Elongation
at Break
%
Heat
Resistance
F ( C) for
30 MinutesComments
Based on ASTM Test Method: D-3330 D-3759 D-3759
Scotch

Fine Line Tape 215
4.8 mils (0.12mm)
Rubber
Polyethylene/
Polypropylene
Co-polymer
43 (47) 15 (263) 1150
250
(121)
Excellent conformability for complex
shapes and irregular surfaces where paper
masking tapes or other plastic tapes cannot
conform. Medium temperature.
Scotch

Fine Line Tape 218
5.0 mils (0.13mm)
Rubber
Polypropylene
37 (40) 13 (228) 720
250
(121)
Good for long, straight lines. Backing is
stiffer than vinyl tapes, while conforming
easily around corners.
Scotch

Fine Line
Masking Tape 265
5.1 mils (0.13mm)
Rubber/Silicone
Polypropylene
21 (23) 21 (368) 881
200
(93)
In-mold composite masking where
sharp, clean, gel-coat color separation
lines are desired. For difficult to stick
to surfaces, such as semi-perm mold
release surfaces.
Scotch

Ultimate Paint Edge
Masking Tape 2460
3.3 mils (0.08mm)
Acrylic
Flatback Paper
8 (8.7) 17 (297) 5
300
(149)
For paint bake operations at temperatures
up to 300 F (149 C). 21 days outdoor.
Scotch

Masking Tape 2800
4.1 mils (0.05mm)
Acrylic
Polyolefin
16 (17) 25 (430) 1000
300
(149)
Alternative for paint systems prone to
residue, tape tracking and ghosting by
rubber adhesive tapes. For paint masking
on TPO (thermoplastic olefin) surfaces.
Translucent backing assists in placement.
7 days outdoor.
Scotch

High Temperature
Fine Line Tape
4735 / 4735L
5.4 mils (0.14mm)
Rubber
Vinyl
9.5 (10.4)14 (245) 130
300
(149)
Highly conformable, high temperature vinyl
fine line tape for fascia panels, two-tone and
other multiple color applications where
critical paint break lines are required.
4735L is linered version.
Scotch

High Temperature
Fine Line Tape
4737T / 4737TL
5.4 mils (0.14mm)
Rubber
Vinyl
10.5 (11.5)16 (280) 115
300
(149)
Conformable, high temperature vinyl fine
line tape for fascia panels, two-tone and
other multiple color applications where
critical paint break lines are required.
4737TL is linered version.
Scotch

High Temperature
Fine Line Tape
4737S / 4737SL
5.4 mils (0.14mm)
Rubber
Vinyl
10.5 (11.5)16 (280) 115
300
(149)
Highly visible backing version of 4737T.
4737SL is linered version.
Note: This technical information and data should be considered representative or typical only and should not be used for specification purposes.
If you re looking for superior masking solutions for demanding
paint requirements, look to Scotch

Fine Line Masking Tapes.
We have a comprehensive lineup of tape solutions designed to
provide a secure hold while allowing for easy removal resulting
in consistent delivery of the sharpest paint lines possible.

35TP565957_TDS.pdf

Sat, 27 Sep 2025 10:05:25 +0000

PRODUCT SHEET
MASKING TAPE MTY
MARKETS
Automotive

Marine &
Comp
FORMS
Roll
FEATURES BENEFITS
Excellent adhesion >
Good mechanical strength
Flexible >
Easy to shape on
contours
Solvent resistant >
Paint will not bleed
Consistency of thickness>
Uniform paint edge
Easy roll release >
Easy to apply
Page 1/2 – Printed in 2017-10-05

PRODUCT SHEET
MASKING TAPE MTY
PRODUCT SPECIFICATIONS
Backing Colour Size Thickness Adhesive
Adhesion
to steel
Elong.
Temp.
range
Crepe PaperYellow 18mm x 50m 0,145 mm Natural Rubber300g / cm 9% 110 C / 1hr
Crepe PaperYellow 24mm x 50m 0,145 mm Natural Rubber300g / cm 9% 110 C / 1hr
Crepe PaperYellow36mm x 50m 0,145 mm Natural Rubber300g / cm 9% 110 C / 1hr
Crepe PaperYellow 48mm x 50m 0,145 mm Natural Rubber300g / cm 9% 110 C / 1hr
Page 2/2 – Printed in 2017-10-05

35TP563199_TDS.pdf

Sat, 27 Sep 2025 10:05:25 +0000

PRODUCT SHEET
MASKING TAPE MTY
MARKETS
Automotive

35TP556771_TDS.pdf

Sat, 27 Sep 2025 10:05:24 +0000

PRODUCT SHEET
MASKING TAPE MTY
MARKETS
Automotive

35TP556740_TDS.pdf

Sat, 27 Sep 2025 10:05:23 +0000

PRODUCT SHEET
MASKING TAPE MTY
MARKETS
Automotive

35TP16166_TDS.pdf

Sat, 27 Sep 2025 10:05:22 +0000

Technical Data Sheet
3M PTFE Skived Film Tape 5480
English-US
Last Revision Date: June, 2024
Supersedes: October, 2016
Product Details Regulatory Info/SDS
Product Description
3M PTFE Skived Film Tape 5480 offers an extremely low coefficient of friction which, in combination with a pressure
sensitive silicone adhesive, creates a smooth, non-stick surface over a variety of substrates to assist in the movement of
web materials in many types of roll-wrap applications
Product Features
Skived 3M PTFE Film Tapes are more conformable than typical extruded PTFE film tapes.
Provides excellent chemical resistance except to organic solvents. Note: The silicone adhesive will be attacked by
commercial organic solvents and so are not recommended for applications requiring organic resistance.
Silicone adhesive provides clean removal from a variety of surfaces.
Non-stick PTFE film provides an exceptionally slick surface for easy clean-up.
Technical Information Note
The following technical information and data should be considered representative or typical only and should not be used
for specification purposes.
Typical Physical Properties
Attribute Name Test Method Value
Color Gray
Adhesive Type Silicone
Backing Skived PTFE (polytetrafluorethylene)
Backing Thickness ASTM D3652 0.05 mm (2 mil)
Total Tape Thickness ASTM D3652 0.09 mm (3.7 mil)
Typical Performance Characteristics
Attribute Name Test Method Temperature Value
180 Peel Adhesion ASTM D3330 22 C (72 F) 2.2 N/cm (20 oz/in)
Elongation at Break ASTM D3759 140 %
Tensile Strength ASTM D3759 46.1 N/cm (416 oz/in)
Long Term Temperature
Resistance
260 C (500 F)
Minimum Long Term
Temperature Resistance
-54 C (-65 F)
12 in/min (300 mm/min)
Long Term (day, weeks)
3M PTFE Skived Film Tape 5480 | English-US 1/2

Handling/Application Information
Application Examples
Easy-release surface provided by wrapping rollers, plates, belts, etc. where build- up of sticky materials and inks can
occur.
Shielding and protecting against chemicals.
Mold release for composite or metal bonding.
High temperature wire bundling and harnessing.
High strength and abrasion resistance reduce friction between surfaces, minimizing squeak and noise.
Wide temperature range for performance on heated machinery and equipment.
CAUTION:When PTFE film tape is exposed to temperatures above 600 F (316 C), small quantities of hazardous vapors
may be released. INHALATION OF THESE VAPORS MAY BE HARMFUL OR MAY CAUSE RESPIRATORY TRACT IRRITATION.
Do not heat or expose PTFE film tape to temperatures above 600 F (316 C).
Storage and Shelf Life
Store under normal conditions of 16 to 27 C (60 to 80 F) and 40 to 60% relative humidity in the original packaging,
out of direct sunlight. For best performance, use this product within 24 months from date of manufacture.
Available Sizes
Attribute Name Value
Standard Roll Length 32.9 m (36 yd)
Information
Technical Information: The technical information, guidance, and other statements contained in this document or otherwise provided by 3M are based
upon records, tests, or experience that 3M believes to be reliable, but the accuracy, completeness, and representative nature of such information is not
guaranteed. Such information is intended for people with knowledge and technical skills sufficient to assess and apply their own informed judgment to the
information. No license under any 3M or third party intellectual property rights is granted or implied with this information.
Product Selection and Use: Many factors beyond 3M s control and uniquely within user s knowledge and control can affect the use and performance of
a 3M product in a particular application. As a result, customer is solely responsible for evaluating the product and determining whether it is appropriate
and suitable for customer s application, including conducting a workplace hazard assessment and reviewing all applicable regulations and standards (e.g.,
OSHA, ANSI, etc.). Failure to properly evaluate, select, and use a 3M product and appropriate safety products, or to meet all applicable safety regulations,
may result in injury, sickness, death, and/or harm to property.
Warranty, Limited Remedy, and Disclaimer: Unless a different warranty is specifically stated on the applicable 3M product packaging or product
literature (in which case such warranty governs), 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the
product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR
CONDITION OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ARISING OUT OF A COURSE OF DEALING, CUSTOM, OR USAGE OF TRADE. If a
3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M s option, replacement of the 3M product or refund of the
purchase price.
Limitation of Liability: Except for the limited remedy stated above, and except to the extent prohibited by law, 3M will not be liable for any loss or
damage arising from or related to the 3M product, whether direct, indirect, special, incidental, or consequential (including, but not limited to, lost profits or
business opportunity), regardless of the legal or equitable theory asserted, including, but not limited to, warranty, contract, negligence, or strict liability.
Disclaimer: 3M industrial and occupational products are intended, labeled, and packaged for sale to trained industrial and occupational customers for
workplace use. Unless specifically stated otherwise on the applicable product packaging or literature, these products are not intended, labeled, or
packaged for sale to or use by consumers (e.g., for home, personal, primary or secondary school, recreational/sporting, or other uses not described in the
applicable product packaging or literature), and must be selected and used in compliance with applicable health and safety regulations and standards
(e.g., U.S. OSHA, ANSI), as well as all product literature, user instructions, warnings, and limitations, and the user must take any action required under any
recall, field action or other product use notice. Misuse of 3M industrial and occupational products may result in injury, sickness, or death. For help with
product selection and use, consult your on-site safety professional, industrial hygienist, or other subject matter expert. For additional product information,
visit www.3M.com.
ISO Statement
This product was manufactured under a 3M quality system registered to ISO 9001 standards.
3M Industrial Adhesives and Tapes Division
3M Center, St. Paul, MN 55144-1000
3M.com/iatd
3M is a trademark of 3M Company.
3M 2024 (6/24)
3M PTFE Skived Film Tape 5480 | English-US 2/2

35TP82B_SDS.pdf

Sat, 27 Sep 2025 07:03:58 +0000

Scotch Fine Line Tape 218 08/30/23

__________________________________________________________________________________________

Page 1 of 5
Article Information Sheet
Copyright,2023, 3M Company.
All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is
allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from
3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.
This Article Information Sheet is provided as a courtesy in response to a customer request. A Safety Data Sheet (SDS) has not
been prepared for these product(s) because they are articles. Articles are not subject to the Occupational Safety and Health
Administration s Hazard Communication Standard (29 CFR 1910.1200(b)(6)(v)). As defined in this standard: Article
means a manufactured item other than a fluid or particle: (i) which is formed to a specific shape or design during
manufacture; (ii) which has end use function(s) dependent in whole or in part upon its shape or design during end use; and
(iii) which under normal conditions of use does not release more than very small quantities, e.g., minute or trace amounts of a
hazardous chemical, and does not pose a physical hazard or health risk to employees.
Document Group:24-5674-7Version Number:1.00Issue Date:08/30/23Supercedes Date:Initial Issue
SECTION 1: Identification
1.1. Product identifier
Scotch Fine Line Tape 218

1.2. Recommended use and restrictions on use
Recommended use
Attachment/Reinforcement, Industrial use
1.3. Supplier s details
MANUFACTURER:3MDIVISION:Industrial Adhesives and Tapes DivisionADDRESS:3M Center, St. Paul, MN 55144-1000, USATelephone:1-888-3M HELPS (1-888-364-3577)
1.4. Emergency telephone number
1-800-364-3577 or (651) 737-6501 (24 hours)
SECTION 2: Hazard identification
This product is exempt from hazard classification according to OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 3: Composition/information on ingredients
IngredientC.A.S. No.% by WtPolypropylene BackingNone 60 – 85 Trade Secret *Rubber AdhesiveTrade Secret* 15 – 40 Trade Secret *
*The specific chemical identity and/or exact percentage (concentration) of this composition has been withheld as a trade
secret.

Scotch Fine Line Tape 218 08/30/23

__________________________________________________________________________________________

Page 2 of 5
SECTION 4: First aid measures
4.1. Description of first aid measures
Inhalation:
No need for first aid is anticipated.
Skin Contact:
No need for first aid is anticipated.
Eye Contact:
No need for first aid is anticipated.
If Swallowed:
No need for first aid is anticipated.
SECTION 5: Fire-fighting measures
In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam.
SECTION 6: Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
Not applicable.
6.2. Environmental precautions
Not applicable.
6.3. Methods and material for containment and cleaning up
Not applicable.
SECTION 7: Handling and storage
7.1. Precautions for safe handling
This product is considered to be an article which does not release or otherwise result in exposure to a hazardous chemical
under normal use conditions.
7.2. Conditions for safe storage including any incompatibilities
No special storage requirements.
SECTION 8: Exposure controls/personal protection
This product is considered to be an article which does not release or otherwise result in exposure to a hazardous chemical
under normal use conditions. No engineering controls or personal protective equipment (PPE) are necessary.
SECTION 9: Physical and chemical properties
9.1. Information on basic physical and chemical properties
Appearance
Physical state
Color
Solid
Green

Scotch Fine Line Tape 218 08/30/23

__________________________________________________________________________________________

Page 3 of 5
Specific Physical Form: Roll of TapeOdorRubberOdor thresholdNot ApplicablepHNot ApplicableMelting pointNot ApplicableBoiling PointNot ApplicableFlash PointNot ApplicableEvaporation rateNot ApplicableFlammability (solid, gas)Not ClassifiedFlammable Limits(LEL)Not ApplicableFlammable Limits(UEL)Not ApplicableVapor PressureNot ApplicableVapor DensityNot ApplicableDensityNot ApplicableSpecific GravityNot ApplicableSolubility in WaterNilSolubility- non-waterNot ApplicablePartition coefficient: n-octanol/ waterNo Data AvailableAutoignition temperatureNot ApplicableDecomposition temperatureNot ApplicableViscosityNot ApplicableMolecular weightNo Data AvailableVolatile Organic CompoundsNot ApplicablePercent volatileNot ApplicableVOC Less H2O & Exempt SolventsNot Applicable
SECTION 10: Stability and reactivity
This material is considered to be non reactive under normal use conditions.
SECTION 11: Toxicological information
Inhalation:
No health effects are expected
Skin Contact:
No health effects are expected
Eye Contact:
No health effects are expected
Ingestion:
No health effects are expected
Additional Information:
This product, when used under reasonable conditions and in accordance with the directions for use, should not present a
health hazard. However, use or processing of the product in a manner not in accordance with the product’s directions for use
may affect the performance of the product and may present potential health and safety hazards.
SECTION 12: Ecological information

Scotch Fine Line Tape 218 08/30/23

__________________________________________________________________________________________

Page 4 of 5
This article is expected to present a low environmental risk either because use and disposal are unlikely to result in a
significant release of components to the environment or because those components that may be released are expected to have
insignificant environmental impact.
SECTION 13: Disposal considerations
Dispose of contents/container in accordance with the local/regional/national/international regulations.
SECTION 14: Transport Information

Not regulated per U.S. DOT, IATA or IMO.
These transportation classifications are provided as a customer service. As the shipper YOU remain responsible for
complying with all applicable laws and regulations, including proper transportation classification and packaging. 3M
transportation classifications are based on product formulation, packaging, 3M policies and 3M understanding of applicable
current regulations. 3M does not guarantee the accuracy of this classification information. This information applies only to
transportation classification and not the packaging, labeling, or marking requirements. The original 3M package is certified
for U.S. ground shipment only. If you are shipping by air or ocean, the package may not meet applicable regulatory
requirements.
SECTION 15: Regulatory information
Chemical Inventories
This product is an article as defined by TSCA regulations, and is exempt from TSCA Inventory requirements.
SECTION 16: Other information
NFPA Hazard Classification
Health: 0 Flammability: 1 Instability: 0 Special Hazards: None

National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address
the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar
emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include
the toxic properties of combustion or decomposition products that are known to be generated in significant quantities.

Document Group:24-5674-7Version Number:1.00Issue Date:08/30/23Supercedes Date:Initial Issue
DISCLAIMER: The information in this Article Information Sheet (AIS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF
PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular
purpose and suitable for user’s method of use or application. Given the variety of factors that can affect the use and
application of a 3M product, some of which are uniquely within the user’s knowledge and control, it is essential that the user
evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for user’s method of use or
application.

3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer
may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness
or accuracy. In addition, information obtained from a database may not be as current as the information in the AIS available
directly from 3M
3M USA AISs are available at www.3M.com

Scotch Fine Line Tape 218 08/30/23

__________________________________________________________________________________________

Page 5 of 5

35TP4252_SDS.pdf

Sat, 27 Sep 2025 07:03:57 +0000

Material Safety Data Sheet

Copyright, 2012, 3M Company All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
This material safety data sheet (MSDS) is provided as a courtesy in response to a customer request. This product is not regulated
under, and a MSDS is not required for this product by the OSHA Hazard Communication Standard (29 CFR 1910.1200) because,
when used as recommended or under ordinary conditions, it should not present a health and safety hazard. However, use or
processing of the product not in accordance with the product’s recommendations or not under ordinary conditions may affect the
performance of the product and may present potential health and safety hazards.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: 3M Aluminum Foil Tape 425, 427, 431, 439, 1402, 1404, 1406, 1410, 1417, 1449,
1450, 97065 & 3M High Temperature Al Foil Tape 433 & 433L & 3M Heavy Duty
Al Foil Tape 438 & Scotch Foil Tape 3311 & 3326 and Headliner Tape 12150
MANUFACTURER: 3M
DIVISION: Industrial Adhesives and Tapes Division
ADDRESS: 3M Center, St. Paul, MN 55144-1000
EMERGENCY PHONE: 1 -800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 11/05/12
Supercedes Date: 11/05/12
Document Group:26-6700-4
Product Use:
Specific Use: Sealing, Bundling, Attachment and Reinforcement
Intended Use: Industrial use
3M Aluminum Foil Tape 425, 427, 431, 439, 1402, 1404, 1406, 1410, 1417, 1449, 1450 & 97065
3M High Temperature Aluminum Foil Tape 433 & 433L
3M Heavy Duty Aluminum Foil Tape 438
3M Scotch Foil Tape 3311 & 3326
3M Aluminum Foil Headliner Tape 12150
SECTION 2: INGREDIENTS
Ingredient C.A.S. No. % by Wt
Aluminum Foil Backing None 51 -99
Acrylic, Rubber, or Silicone Adhesive Trade Secret 1 -49

MATERIAL SAFETY DATA SHEET 3M AluminumFoil Tape 425, 427, 431, 439, 1402, 1404, 1406, 1410, 1417, 1449, 1450, 97065 &
3M High Temperature Al Foil Tape 433 & 433L & 3M Heavy Duty Al Foil Tape 438 & Scotch Foil Tape 3311 & 3326 and
Headliner Tape 12150 11/05/12
_________________________________________________________________________________________________
Page 2of 6
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Odor, Color, Grade: silver colored aluminum foil tapes with silicone, rubber, or acrylic adhesive with or without liner
General Physical Form: Solid
Immediate health, physical, and environmental hazards: The environmental properties of this product present a low
environmental hazard. This product, when used under reasonable conditions and in accordance with the 3M directions for use, should
not present a health hazard. However, use or processing of the product in a manner not in accordance with the product’s directions for
use may affect the performance of the product and may present potential health and safety hazards.
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:
No health effects are expected.
Skin Contact:
No health effects are expected.
Inhalation:
No health effects are expected.
Ingestion:
No health effects are expected.
3.3 POTENTIAL ENVIRONMENTAL EFFECTS
This substance does not leach metals or other RCRA (Resource Conservation and Recovery Act) listed TCLP (Toxic Characteristic
Leaching Procedure) hazardous substances at concentrations that would make the product a hazardous waste.

SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriatepersonal and industrial hygiene practices are
followed.
Eye Contact: No need for first aid is anticipated.
Skin Contact: No need for first aid is anticipated.
Inhalation: No need for first aid is anticipated.
If Swallowed: No need for first aid is anticipated.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
Autoignition temperature Not Applicable
Flash Point Not Applicable
Flammable Limits(LEL) Not Applicable

MATERIAL SAFETY DATA SHEET 3M AluminumFoil Tape 425, 427, 431, 439, 1402, 1404, 1406, 1410, 1417, 1449, 1450, 97065 &
3M High Temperature Al Foil Tape 433 & 433L & 3M Heavy Duty Al Foil Tape 438 & Scotch Foil Tape 3311 & 3326 and
Headliner Tape 12150 11/05/12
_________________________________________________________________________________________________
Page 3of 6
Flammable Limits(UEL) Not Applicable
5.2 EXTINGUISHING MEDIA
Use fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus
(SCBA).
Unusual Fire and Explosion Hazards: No unusual fire or explosion hazards are anticipated.
SECTION 6: ACCIDENTAL RELEASE MEASURES
6.1. Personal precautions, protective equipment and emergency procedures
Not applicable.
6.2. Environmental precautions
Not applicable.
Clean-up methods
Not applicable.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
This product is considered to be an article which does not release or otherwise result in exposure to a hazardous chemical under
normal use conditions.
7.2 STORAGE
Not applicable.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
Not applicable.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact.

8.2.2 Skin Protection
Avoid prolonged or repeated skin contact.
8.2.3 Respiratory Protection
Under normal use conditions, airborne exposures are not expected to be significant enough to require respiratory protection.

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Odor, Color, Grade: silver colored aluminum foil tapes with silicone, rubber, or acrylic
adhesive with or without liner
General Physical Form: Solid
Autoignition temperature Not Applicable
Flash Point Not Applicable
Flammable Limits(LEL) Not Applicable
Flammable Limits(UEL) Not Applicable
Boiling Point Not Applicable
Density Not Applicable
Vapor Density Not Applicable
Vapor Pressure Not Applicable
Specific Gravity Not Applicable
pH Not Applicable
Melting point Not Applicable
Solubility in Water Nil
Evaporation rate Not Applicable
Volatile Organic Compounds Not Applicable
Kow -Oct/Water partition coef Not Applicable
Percent volatile Not Applicable
VOC Less H2O & Exempt Solvents Not Applicable
Viscosity Not Applicable
SECTION 10: STABILITY AND REACTIVITY
Stability:Stable.
Materials and Conditions to Avoid:
10.1 Conditions to avoid
None known

10.2 Materials to avoid
None known
Hazardous Polymerization: Hazardous polymerization will not occur.
Hazardous Decomposition: Under recommended usage conditions, hazardous decomposition products are not expected. Hazardous

SECTION 11: TOXICOLOGICAL INFORMATION
Please contact the address listed onthe first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION
ECOTOXICOLOGICAL INFORMATION
Not determined.
CHEMICAL FATE INFORMATION
Not determined.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Reclaim if feasible. If product can’t be reclaimed, dispose of waste product in a sanitary landfill.
Alternatively, incinerate the waste product in an industrial, commercial, or municipal incinerator.
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
Not regulated per U.S. DOT, IATA or IMO.
These transportation classifications are provided as a customer service. As the shipper YOU remain responsible for
complying with all applicable laws and regulations, including proper transportation classification and packaging.3M
transportation classifications are based on product formulation, packaging, 3M policies and 3M understanding of applicable
current regulations. 3M does not guarantee the accuracy of this classification information. This information applies only to
transportation classification and notthe packaging, labeling, or marking requirements.The original 3Mpackage is certified
for U.S. ground shipment only. If you are shipping by air or ocean, the package may not meet applicable regulatory
requirements.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONS
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard -No Pressure Hazard -No Reactivity Hazard -No Immediate Hazard -No Delayed Hazard -No

National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.

Revision Changes:
Section 2: Product identification comment was modified.
Section 1: Product name was modified.
Page Heading: Product name was modified.
Section 2: Product identification comment was modified.
Section 2: Ingredient table was modified.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTIC ULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user’s method of
use or application. Given the variety of factors that can affect the useand application of a 3M product, some of which are uniquely
within the user’s knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user’s method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M

3MUSA MSDSs are available at www.3M.com

35TP4251_SDS.pdf

Sat, 27 Sep 2025 07:03:57 +0000

Material Safety Data Sheet

MATERIAL SAFETY DATA SHEET 3M AluminumFoil Tape 425, 427, 431, 439, 1402, 1404, 1406, 1410, 1417, 1449, 1450, 97065 &
3M High Temperature Al Foil Tape 433 & 433L & 3M Heavy Duty Al Foil Tape 438 & Scotch Foil Tape 3311 & 3326 and
Headliner Tape 12150 11/05/12
_________________________________________________________________________________________________
Page 3of 6
Flammable Limits(UEL) Not Applicable
5.2 EXTINGUISHING MEDIA
Use fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus
(SCBA).
Unusual Fire and Explosion Hazards: No unusual fire or explosion hazards are anticipated.
SECTION 6: ACCIDENTAL RELEASE MEASURES
6.1. Personal precautions, protective equipment and emergency procedures
Not applicable.
6.2. Environmental precautions
Not applicable.
Clean-up methods
Not applicable.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
This product is considered to be an article which does not release or otherwise result in exposure to a hazardous chemical under
normal use conditions.
7.2 STORAGE
Not applicable.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
Not applicable.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact.

National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.

3MUSA MSDSs are available at www.3M.com

35TP4152_SDS.pdf

Sat, 27 Sep 2025 07:03:56 +0000

35TP3732_SDS.pdf

Sat, 27 Sep 2025 07:03:55 +0000

Material Safety Data Sheet

Copyright, 2012, 3M Company All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
This material safety data sheet (MSDS) is provided as a courtesy in response to a customer request. This product is not regulated
under, and a MSDS is not required for this product by the OSHA Hazard Communication Standard (29 CFR 1910.1200) because,
when used as recommended or under ordinary conditions, it should not present a health and safety hazard. However, use or
processing of the product not in accordance with the product’s recommendatio ns or not under ordinary conditions may affect the
performance of the product and may present potential health and safety hazards.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: 3M Scotch and Tartan Box Sealing Tapes -Rubber AdhesiveSeries (255, 351, 353,
355, 369, 371, 372, 373, 375, 3073, 3331, 3721, 3723, 3732, 3734, 3779, 3781, 3782, 3783,
3785, 3875)
MANUFACTURER: 3M
DIVISION: Industrial Adhesives and Tapes Division
ADDRESS: 3M Center, St. Paul, MN 55144-1000
EMERGENCY PHONE: 1 -800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 02/29/12
Supercedes Date: 08/19/10
Document Group:26-0526-9
Product Use:
Specific Use: Box Sealing Tapes
Intended Use: Industrial use
3M Tartan Box Sealing Tape 369 (Clear and Tan)
3M Scotch Box Sealing Tape 351, 353, 371, 372 and 373 (various colors)
3M Scotch Box Sealing Tape 3073
3M Scotch Cold Temperature Box Sealing Tape 3331
3M Scotch High Performance Cold Temperature Box Sealing Tape 3723
3M Scotch High Tack Box Sealing Tape 3743 (Clear and Tan)
3M Scotch Industrial Cold Temperature Box Sealing Tape 3721
3M Scotch Industrial Continuous Taping System Tape 3781, 3782, 3783 and 3785
3M Scotch Packadge Sealing Tape 255
3M Scotch Printed Message Box Sealing Tape 3732 and 3734
3M Scotch Superior Performance Box Sealing Tape 355, 375 and 3875 (Clear and Tan)
3M Scotch Security Message Box Sealing Tape 3779

8.2.4 Preventionof Swallowing
Not an expected route of exposure.
8.3 EXPOSURE GUIDELINES
None Established

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Specific Physical Form: Roll of Tape
Odor, Color, Grade: paper, polyester or polypropylene tape with rubber adhesive, various
colors and printing
General Physical Form: Solid
Autoignition temperature Not Applicable
Flash Point Not Applicable
Flammable Limits(LEL) Not Applicable
Flammable Limits(UEL) Not Applicable
Boiling Point Not Applicable
Density Not Applicable
Vapor Density Not Applicable
Vapor Pressure Not Applicable
Specific Gravity Not Applicable
pH Not Applicable
Melting point Not Applicable
Solubility in Water Nil
Evaporation rate Not Applicable
Volatile Organic Compounds Not Applicable
Percent volatile Not Applicable
VOC Less H2O & Exempt Solvents Not Applicable
Viscosity Not Applicable
SECTION 10: STABILITY AND REACTIVITY
Stability:Stable.
Materials and Conditions to Avoid:
10.1 Conditions to avoid
None known

10.2 Materials to avoid
None known

Hazardous Decomposition: Under recommended usage conditions, hazardous decomposition products are not expected. Hazardous
decomposition products may occur as a result of oxidation, heating, or reaction with another material.

National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.

Revision Changes:
Section 1: Product name was modified.
Section 1: Product use information was modified.
Section 16: Disclaimer (second paragraph) was modified.
Section 5: Unusual fire and explosion hazard information was modified.
Section 8: Eye/face protection phrase was modified.
Section 10: Hazardous decomposition or by-products table was modified.
Section 13: Waste disposal method information was modified.
Section 14: Transportation legal text was modified.
Page Heading: Productname was modified.
Section 9: Density information was modified.
Section 9: Vapor density value was modified.

MATERIAL SAFETY DATA SHEET 3M Scotch and Tartan Box Sealing Tapes -Rubber Adhesive Series (255, 351, 353, 355, 369,
371, 372, 373, 375, 3073, 3331, 3721, 3723, 3732, 3734, 3779, 3781, 3782, 3783, 3785, 3875) 02/29/12
_________________________________________________________________________________________________
Page 7of 8
Section 9: Vapor pressure value was modified.
Section 9: Boiling point information was modified.
Section 5: Flammable limits (UE) information was modified.
Section 5: Flammable limits (LEL) information was modified.
Section 5: Autoignition temperature information was modified.
Section 5: Flash point information was modified.
Section 9: Property description for optional properties was modified.
Section 9: Specific gravity information was modified.
Section 9: pH information was modified.
Section 9: Melting point information was modified.
Section 9: Solubility in water text was modified.
Section 9: Flash point information was modified.
Section 9: Flammable limits (LEL) information was modified.
Section 9: Flammable limits (UEL) information was modified.
Section 9: Autoignition temperature information was modified.
Section 2: Product identification comment was modified.
Section 12: Ecotoxicological phrase was modified.
Section 12: Chemical Fate phrase was modified.
Section 2: Ingredient table was modified.
Section 6: 6.2. Environmental precautions heading was modified.
Section 6: 6.1. Personal precautions, protective equipment and emergency procedures heading was modified.
Section 4: First aid for eye contact -decontamination -was added.
Section 4: First aid for eye contact -medical assistance -was added.
Section 4: First aid for skin contact -decontamination -was added.
Section 4: First aid for skin contact -medical assistance -was added.
Section 16: Web address was added.
Section 8: Hand protection information was added.
Section 1: Address was added.
Copyright was added.
Company logo was added.
Telephone header wa s added.
Company Telephone was added.
Section 1: Emergency phone information was added.
Section 1: Emergency phone information was deleted.
Company Logo was deleted.
Copyright was deleted.
Section 16: Web address heading was deleted.
Section 1: Address line 1 was deleted.
Section 1: Address line 2 was deleted.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product isfit for a particular purpose and suitable for user’s method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user’s knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user’s method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M

3MUSA MSDSs are available at www.3M.com

35TP23372_SDS.pdf

Sat, 27 Sep 2025 07:03:55 +0000

Material Safety Data Sheet

Copyright, 2008, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original isresold or otherwise distributed with the intention of earning a profit
thereon.
This material safety data sheet (MSDS) is provided as a courtesy in response to a customer request. This product is not regulated
under, and a MSDS is not required for this product by the OSHA Hazard Communication Standard (29 CFR 1910.1200) because,
when used as recommended or under ordinary conditions, it should not present a health and safety hazard. However, use or
processing of the product not in accordance with the product’s recommendations or not under ordinary conditions may affect the
performance of the product and may present potential health and safety hazards.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: 3M(TM) Performance Masking Tape 2308,Highland(TM) Masking Tape 2727, Scotch(r)
Automotive Refinish Masking Tape 233, Scotch(r) Performance Masking Tape 233+, &
Tartan(TM) Paper Tape 000
MANUFACTURER: 3M
DIVISION: Automotive Aftermarket
ADDRESS: 3M Center
St. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 12/29/2008
Supercedes Date: Initial Issue
Document Group:26-0757-0
Product Use:
Specific Use: Masking
Intended Use: Industrial use
SECTION 2: INGREDIENTS
Ingredient C.A.S. No. % by Wt
Paper Backing None 51 -99
Rubber Adhesive Trade Secret 1 -49
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Odor, Color, Grade: natural or bright green (233+) paper tape
General Physical Form: Solid

3.3 POTENTIAL ENVIRONMENTAL EFFECTS
This substance does not leach metals or other RCRA (Resource Conservation and Recovery Act) listed TCLP (Toxic Characteristic
Leaching Procedure) hazardous substances at concentrations that would make the product a hazardous waste.

SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: No need for first aid is anticipated.
Skin Contact: No need for first aid is anticipated.
Inhalation: No need for first aid is anticipated.
If Swallowed: No need for first aid is anticipated.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
Autoignition temperature Not Applicable
Flash Point Not Applicable
Flammable Limits -LEL Not Applicable
Flammable Limits -UEL Not Applicable

8.2.2 Skin Protection
Gloves not normally required. Avoid prolonged or repeated skin contact.

8.2.3 Respiratory Protection
Under normal use conditions, airborne exposures are not expected to be significant enough to require respiratory protection.

8.2.4Prevention of Swallowing
Not applicable.
8.3 EXPOSURE GUIDELINES

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Odor, Color, Grade: natural or bright green (233+) paper tape
General Physical Form: Solid
Autoignition temperature Not Applicable
Flash Point Not Applicable
Flammable Limits -LEL Not Applicable
Flammable Limits -UEL Not Applicable
Boiling point Not Applicable
Density Not Applicable
Vapor Density Not Applicable
Vapor Pressure Not Applicable
Specific Gravity Not Applicable
pH Not Applicable
Melting point Not Applicable
Solubility in Water Nil
Evaporation rate Not Applicable
Volatile Organic Compounds Not Applicable
Percent volatile Not Applicable
VOC Less H2O & Exempt Solvents Not Applicable
Viscosity Not Applicable
SECTION 10: STABILITY AND REACTIVITY
Stability:Stable.
Materials and Conditions to Avoid: None known

Hazardous Polymerization: Hazardous polymerization will not occur.

Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION

MATERIAL SAFETY DATA SHEET 3M(TM) Performance Masking Tape 2308, Highland(TM) Masking Tape 2727, Scotch(r)
Automotive Refinish Masking Tape 233, Scotch(r) Performance Masking Tape 233+, & Tartan(TM) Paper Tape 000 12/29/2008
_________________________________________________________________________________________________
Page 5of 6
ECOTOXICOLOGICAL INFORMATION
Not determined.
CHEMICAL FATE INFORMATION
Not determined.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Reclaim if feasible. If product can’t be reclaimed, dispose of waste product in a sanitary landfill.
Alternatively, incinerate the waste product in an industrial, commercial, or municipal incinerator.
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
Not regulated per U.S. DOT, IATA or IMO.
These transportation classifications are provided as a customer service. As the shipper YOU remain responsible for
complying with all applicable laws and regulations, including proper transportation classification and packaging.3M’s
transportation classifications are based on product formulation, packaging, 3M policies and 3M’s understanding of applicable
current regulations. 3M does not guarantee the accuracy of this classification information. This information applies only to
transportation classification and notthe packaging, labeling, or marking requirements.The original 3M package is certified
for U.S. ground shipment only. If you are shipping by air or ocean, the package may not meet applicable regulatory
requirements.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONS
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard -No Pressure Hazard -No Reactivity Hazard -No Immediate Hazard -No Delayed Hazard -No

STATE REGULATIONS
Contact 3M for more information.

INTERNATIONAL REGULATIONS
Contact 3M for more information.

This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION
NFPA Hazard Classification
Health: 0 Flammability: 1 Reactivity: 0 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.

No revision information is available.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANT Y
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user’s method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user’s knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user’s method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.

3M MSDSs are available at www.3M.com

35TP2336_SDS.pdf

Sat, 27 Sep 2025 07:03:54 +0000

Material Safety Data Sheet

SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: No need for first aid is anticipated.
Skin Contact: No need for first aid is anticipated.
Inhalation: No need for first aid is anticipated.
If Swallowed: No need for first aid is anticipated.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
Autoignition temperature Not Applicable
Flash Point Not Applicable
Flammable Limits -LEL Not Applicable
Flammable Limits -UEL Not Applicable

8.2.2 Skin Protection
Gloves not normally required. Avoid prolonged or repeated skin contact.

8.2.3 Respiratory Protection
Under normal use conditions, airborne exposures are not expected to be significant enough to require respiratory protection.

8.2.4Prevention of Swallowing
Not applicable.
8.3 EXPOSURE GUIDELINES

Hazardous Polymerization: Hazardous polymerization will not occur.

Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION

STATE REGULATIONS
Contact 3M for more information.

INTERNATIONAL REGULATIONS
Contact 3M for more information.

3M MSDSs are available at www.3M.com

35TP23348_SDS.pdf

Sat, 27 Sep 2025 07:03:53 +0000

Material Safety Data Sheet

SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: No need for first aid is anticipated.
Skin Contact: No need for first aid is anticipated.
Inhalation: No need for first aid is anticipated.
If Swallowed: No need for first aid is anticipated.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
Autoignition temperature Not Applicable
Flash Point Not Applicable
Flammable Limits -LEL Not Applicable
Flammable Limits -UEL Not Applicable

8.2.2 Skin Protection
Gloves not normally required. Avoid prolonged or repeated skin contact.

8.2.3 Respiratory Protection
Under normal use conditions, airborne exposures are not expected to be significant enough to require respiratory protection.

8.2.4Prevention of Swallowing
Not applicable.
8.3 EXPOSURE GUIDELINES

Hazardous Polymerization: Hazardous polymerization will not occur.

Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION

STATE REGULATIONS
Contact 3M for more information.

INTERNATIONAL REGULATIONS
Contact 3M for more information.

3M MSDSs are available at www.3M.com

35TP2333_SDS.pdf

Sat, 27 Sep 2025 07:03:52 +0000

Material Safety Data Sheet

SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: No need for first aid is anticipated.
Skin Contact: No need for first aid is anticipated.
Inhalation: No need for first aid is anticipated.
If Swallowed: No need for first aid is anticipated.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
Autoignition temperature Not Applicable
Flash Point Not Applicable
Flammable Limits -LEL Not Applicable
Flammable Limits -UEL Not Applicable

8.2.2 Skin Protection
Gloves not normally required. Avoid prolonged or repeated skin contact.

8.2.3 Respiratory Protection
Under normal use conditions, airborne exposures are not expected to be significant enough to require respiratory protection.

8.2.4Prevention of Swallowing
Not applicable.
8.3 EXPOSURE GUIDELINES

Hazardous Polymerization: Hazardous polymerization will not occur.

Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION

STATE REGULATIONS
Contact 3M for more information.

INTERNATIONAL REGULATIONS
Contact 3M for more information.

3M MSDSs are available at www.3M.com

35TP23336_SDS.pdf

Sat, 27 Sep 2025 07:03:52 +0000

Material Safety Data Sheet

SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: No need for first aid is anticipated.
Skin Contact: No need for first aid is anticipated.
Inhalation: No need for first aid is anticipated.
If Swallowed: No need for first aid is anticipated.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
Autoignition temperature Not Applicable
Flash Point Not Applicable
Flammable Limits -LEL Not Applicable
Flammable Limits -UEL Not Applicable

8.2.2 Skin Protection
Gloves not normally required. Avoid prolonged or repeated skin contact.

8.2.3 Respiratory Protection
Under normal use conditions, airborne exposures are not expected to be significant enough to require respiratory protection.

8.2.4Prevention of Swallowing
Not applicable.
8.3 EXPOSURE GUIDELINES

Hazardous Polymerization: Hazardous polymerization will not occur.

Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION

STATE REGULATIONS
Contact 3M for more information.

INTERNATIONAL REGULATIONS
Contact 3M for more information.

3M MSDSs are available at www.3M.com

35TP23324_SDS.pdf

Sat, 27 Sep 2025 07:03:51 +0000

Material Safety Data Sheet

SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: No need for first aid is anticipated.
Skin Contact: No need for first aid is anticipated.
Inhalation: No need for first aid is anticipated.
If Swallowed: No need for first aid is anticipated.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
Autoignition temperature Not Applicable
Flash Point Not Applicable
Flammable Limits -LEL Not Applicable
Flammable Limits -UEL Not Applicable

8.2.2 Skin Protection
Gloves not normally required. Avoid prolonged or repeated skin contact.

8.2.3 Respiratory Protection
Under normal use conditions, airborne exposures are not expected to be significant enough to require respiratory protection.

8.2.4Prevention of Swallowing
Not applicable.
8.3 EXPOSURE GUIDELINES

Hazardous Polymerization: Hazardous polymerization will not occur.

Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION

STATE REGULATIONS
Contact 3M for more information.

INTERNATIONAL REGULATIONS
Contact 3M for more information.

3M MSDSs are available at www.3M.com

35TP23318_SDS.pdf

Sat, 27 Sep 2025 07:03:50 +0000

Material Safety Data Sheet

SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: No need for first aid is anticipated.
Skin Contact: No need for first aid is anticipated.
Inhalation: No need for first aid is anticipated.
If Swallowed: No need for first aid is anticipated.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
Autoignition temperature Not Applicable
Flash Point Not Applicable
Flammable Limits -LEL Not Applicable
Flammable Limits -UEL Not Applicable

8.2.2 Skin Protection
Gloves not normally required. Avoid prolonged or repeated skin contact.

8.2.3 Respiratory Protection
Under normal use conditions, airborne exposures are not expected to be significant enough to require respiratory protection.

8.2.4Prevention of Swallowing
Not applicable.
8.3 EXPOSURE GUIDELINES

Hazardous Polymerization: Hazardous polymerization will not occur.

Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION

STATE REGULATIONS
Contact 3M for more information.

INTERNATIONAL REGULATIONS
Contact 3M for more information.

3M MSDSs are available at www.3M.com

35TP23312_SDS.pdf

Sat, 27 Sep 2025 07:03:49 +0000

Material Safety Data Sheet

SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: No need for first aid is anticipated.
Skin Contact: No need for first aid is anticipated.
Inhalation: No need for first aid is anticipated.
If Swallowed: No need for first aid is anticipated.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
Autoignition temperature Not Applicable
Flash Point Not Applicable
Flammable Limits -LEL Not Applicable
Flammable Limits -UEL Not Applicable

8.2.2 Skin Protection
Gloves not normally required. Avoid prolonged or repeated skin contact.

8.2.3 Respiratory Protection
Under normal use conditions, airborne exposures are not expected to be significant enough to require respiratory protection.

8.2.4Prevention of Swallowing
Not applicable.
8.3 EXPOSURE GUIDELINES

Hazardous Polymerization: Hazardous polymerization will not occur.

Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION

STATE REGULATIONS
Contact 3M for more information.

INTERNATIONAL REGULATIONS
Contact 3M for more information.

3M MSDSs are available at www.3M.com