by | Sep 27, 2025
22695 Old Canal Road, Yorba Linda, CA 92887 p 714.279.9928 f 714.279.0307
MATERIAL SPECIFICATION
To: Revchem Bloomington
2720 S. Willow Ave
Bloomington, CA 92316
Attn: Russ Tell
Part Number 564381
Part Description 35.5 Rubber Squeegee
Material Natural Rubber
Tensile 1160 psi
Elongation 200%
Hardness 70-75 Shore A
Compression Set 50% max
Heat aged, test method D573, 70 hours at 70 C
Change in tensile strenth +/-30%
Change in elongation -50% max
Change in hardness +/-15 points
Pacifictech Molded Products, Inc. Date: February 10, 2025
by | Sep 27, 2025
Property
Test
Method
Value
Uncured Product
23 +/- 2 C and 50 +/-5% humidity
Color Pale Yellow
Cure Profile
23+/-2 C and 50+/-5%
humidity
Density
BS ISO
2781
0.83 g/cm3
Flash Point C
BS 2000-
34
28 C
Odour Alcohol
Rheology Liquid
Tack Free Time / Skin
Formation at 23 C/73 F
15 min
Viscosity Mixed Brookfield1 cP
Storage
Max Storage Temperature 25 C / 77 F
Min Storage Temperature 5 C / 41 F
Shelf Life 18 mths
Primer No. 6
Primer
Description
This is a specially formulated silicone based primer for use with a
wide range of CHT 1K Condensation / Moisture curing RTV
silicone sealants. This primer imparts good adhesion to most
metals. It is recommended as a primer for use on non-porous
surfaces. For all new applications, it is recommended that
customers carry out small-scale tests to determine the suitability
of the primer and the strength of bond produced.
Key Features
Aerospace approved
Suitable for use with CHT adhesives
Suitable for non porous surfaces
For use with most metals
Key Applications
Rolls Royce MSRR1064
Application
Primer for condensation cure 1 part adhesives on metal
substrates. Not suitable for polycarbonate and acrylic
Use and Cure Information
This primer contains solvents which are classified as hazardous
under current regulations. Users should read the Safety Data
Sheets for this product carefully before use. Surfaces to be
bonded should be dry and free from grease, oil, dust and release
agents. Non-porous substrates, should be solvent degreased prior to application. The primer should be applied with a lint-free cloth or
paintbrush and allowed to dry thoroughly at room temperature for a minimum time equal to the tack free time given in this document, before
applying the sealant. Drying should be carried out in a well-ventilated area. Do not leave longer than 2 hours. The drying/curing time is
dependent on the ambient temperature and humidity. Heat should not be applied to accelerate the drying cycle. Over-application of the
primer will result in poor adhesion. As a guide, one litre of Primer should be sufficient for approximately 15 m . It is absolutely important to
check the compatibility in preliminary tests if unknown substrates are used.
Health & Safety
Safety
Please observe the safety data sheets and the safety statements on the container labels when handling our products. The dangerous goods
regulations and the accident prevention regulations of the professional associations must be particularly observed. Keep the safety data
sheet of the applied product at hand since it provides useful instructions for the safe use and disposal of the product as well as for actions to
be taken in case of accidents.
Revision Date 01 Mar 2024
Revision No 2
Download Date 22 Oct 2024
TECHNICAL DATA SHEET
The content set out in the technical data sheet does not contain information upon which you should rely. It is provided for general information purposes only and does not constitute a product
specification. You must obtain professional or specialist advice before taking any action based on the information provided in the technical data sheet.
CHT make reasonable efforts to ensure that information set out in the technical data sheet is complete, accurate, and up-to-date. CHT do not, however, make any representations, warranties or
guarantees (whether express or implied) that information set out in the technical data sheet is complete, accurate, or up-to-date or that the product will be suitable for your requirements. You
should carry out your own testing to determine the applicability of such information and whether the product will be suitable. CHT reserve the right to modify the technical data sheet at any time.
The CHT technical service department is available to offer further information and advice and should it be needed to look at modifying current products or custom formulate a new one to meet
your specific requirements. Please contact the technical service department.
CHT Germany GmbH: Postfach 12 80, 72002 T bingen, Bismarckstra e 102, 72072 T bingen, Germany
Telephone: 07071/154-0, Fax: 07071/154-290, Email: info@cht.com, Homepage: www.cht.com / www.cht-silicones.com
by | Sep 27, 2025
For technical information call 800.992.2424 or 203.743.4447
For product sales: CT 800.442.3424, CA 800.771.8161, IL 800.447.4866, Canada 800.307.2199
www.miller-stephenson.com
MS-242N
Quik-Freeze
Description
Miller-Stephenson s Quik-Freeze
(MS-242N) is a 14oz
aerosol product that is designed for convenient use in
many industrial applications. It contains HFC 134a
propellant which is a non-ozone depleting chemical.
MS-242N provides a rapid method of cooling small
electronic components. This product is utilized to locate
intermittent malfunctions in electronic equipment.
Applying the Quik-Freeze
will have no effect on
components operating properly but faulty components will
be shocked into failure mode and immediately identified.
MS-242N freezes small areas to -55 F/-48 C.
ADVANTAGES:
Nonconductive
Nonflammable
Odorless
Low order of toxicity
Compatible with most plastics, elastomers, and
metals
Leaves no residue
NSN 6850-01-333-1841
Quik-Freeze
is recommended for:
Heat-cold intermittence testing of electronic
components.
Protection of expensive components during
soldering/desoldering.
Low temperature circuit testing.
Nondestructive testing of electronic and
electromechanical systems.
PHYSICAL PROPERTIES OF HFC 134a:
Molecular weight .. 102.03
Boiling point ..-15.7 F/-26.5 C
Vapor pressure 96.5 psia @ 77 F/25 C
Density .. .1.21 @ 77 F/25 C
VOC . exempt
ODP .. .zero
Safety Data Sheet (SDS) is available upon request
1308-9K
The recommendation made here with and the information set forth with respect to the
performance or use of our products are believed, but not warranted to be accurate. The products
discussed are sold without warranty, as to fitness or performance, express or implied and upon
condition that purchasers shall make their own test to determine suitability of such products for
their particular purposes. Likewise, statements concerning the possible uses of our products are
not intended as recommendations to use our products in the infringement of any patent.
