406303E75D_TDS.pdf
Our Products are intended for sale to industrial and commercial customers. We request that Customers inspect and test our products before use and satisfy themselves as to
contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any warranty or merchantability or fitness, nor is protection from any
law of patent to be inferred. All patent rights are reserved. The exclusive remedy for all proven claims is replacement of our materials and in no event shall we be liable for
special, incidental or consequential damages
7/28/2023 ISO 9001:2015 Registered Company
DURA-KOTE GEL COATS
23XX-XXXM
World Class Coatings
Technology
ELITE LOW VOC COLOR GEL COAT
____________________________________________________________________________________________
Dura-kote Elite Marine gel coat all colors is a low VOC, acrylic modified ISO/NPG polyester gel coat. Dura-
Kote Elite gel coats offer a further improvement in UV stability compared to the Advantage line without
compromising other properties. Elite gel coats should be used where color stability is a primary concern and are
suitable for a wide range of applications including boats, recreational vehicles and a variety of industrial
applications.
PERFORMANCE BENEFITS
Good sag resistance
Excellent flow and leveling
Resistance to pinholing
Superior air release
Excellent UV stability
Good impact resistance
TYPICAL LIQUID GEL COAT PROPERTIES
Gel time @77F, 2% MEKP . 18-24 minutes
Viscosity @ 77F, 20RPM #4 spindle … 5,200-5,800cps
Thixotropic Index . 5.5 minimum
Weight per gallon .. 10+1 lbs/gal (color dependent)
Maximum VOC … <33% by weight volatile
<30% by weight for whites and off whites
(Local regulations vary. Consult your local AQMD to determine actual VOC in use)
USAGE GUIDELINES
Mix this product for at least 5 minutes at low speed prior to use
MEKP levels should be kept at 2%
Do not apply gel coats below 64F
Apply using airless spray at a the lowest possible pressure
Film thickness must be between 15mils and 25mils in 2-3 passes with a short flash off time between passes
SHELF LIFE
This product is stable for six months from date of production when stored away from sunlight at no more than 77F.
Extended storage will result in some drift in gel times and viscosity. Elevated temperatures will reduce shelf life
further
40616831_TDS.pdf
4051506102_TDS.pdf
World Class Coatings
Technology
515-XXX
TRANSPARENT TINTS:
ALL COLORS
____________________________________________________________________________________________
Dura Technologies. The materials in this product are chosen for their compatibility with
unsaturated polyester coatings.
Application:
1. Prior to use, determine the loading requirements for the specific application.
2. The tints should be added to the material under gentle agitation.
3. Mix the resin system for approximately 5 minutes before adding the tints.
4. For more information, refer to the SDS.
WARNING:
This material can affect the gel time and the viscosity of the resin system. Please evaluate this
material thoroughly before using it in production.
Our Products are intended for sale to industrial and commercial customers. We request that Customers inspect and test our products before use and satisfy themselves as to
contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any warranty or merchantability or fitness, nor is protection from any
law of patent to be inferred. All patent rights are reserved. The exclusive remedy for all proven claims is replacement of our materials and in no event shall we be liable for
special, incidental or consequential damages
Last updated 17 December 2019 ISO 9001:2015 Registered Company
4051505002_TDS.pdf
World Class Coatings
Technology
515-XXX
TRANSPARENT TINTS:
ALL COLORS
____________________________________________________________________________________________
Dura Technologies. The materials in this product are chosen for their compatibility with
unsaturated polyester coatings.
Application:
1. Prior to use, determine the loading requirements for the specific application.
2. The tints should be added to the material under gentle agitation.
3. Mix the resin system for approximately 5 minutes before adding the tints.
4. For more information, refer to the SDS.
WARNING:
This material can affect the gel time and the viscosity of the resin system. Please evaluate this
material thoroughly before using it in production.
Our Products are intended for sale to industrial and commercial customers. We request that Customers inspect and test our products before use and satisfy themselves as to
contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any warranty or merchantability or fitness, nor is protection from any
law of patent to be inferred. All patent rights are reserved. The exclusive remedy for all proven claims is replacement of our materials and in no event shall we be liable for
special, incidental or consequential damages
Last updated 17 December 2019 ISO 9001:2015 Registered Company
4051505202_TDS.pdf
World Class Coatings
Technology
515-XXX
TRANSPARENT TINTS:
ALL COLORS
____________________________________________________________________________________________
Dura Technologies. The materials in this product are chosen for their compatibility with
unsaturated polyester coatings.
Application:
1. Prior to use, determine the loading requirements for the specific application.
2. The tints should be added to the material under gentle agitation.
3. Mix the resin system for approximately 5 minutes before adding the tints.
4. For more information, refer to the SDS.
WARNING:
This material can affect the gel time and the viscosity of the resin system. Please evaluate this
material thoroughly before using it in production.
Our Products are intended for sale to industrial and commercial customers. We request that Customers inspect and test our products before use and satisfy themselves as to
contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any warranty or merchantability or fitness, nor is protection from any
law of patent to be inferred. All patent rights are reserved. The exclusive remedy for all proven claims is replacement of our materials and in no event shall we be liable for
special, incidental or consequential damages
Last updated 17 December 2019 ISO 9001:2015 Registered Company
4051504802_TDS.pdf
World Class Coatings
Technology
515-XXX
TRANSPARENT TINTS:
ALL COLORS
____________________________________________________________________________________________
Dura Technologies. The materials in this product are chosen for their compatibility with
unsaturated polyester coatings.
Application:
1. Prior to use, determine the loading requirements for the specific application.
2. The tints should be added to the material under gentle agitation.
3. Mix the resin system for approximately 5 minutes before adding the tints.
4. For more information, refer to the SDS.
WARNING:
This material can affect the gel time and the viscosity of the resin system. Please evaluate this
material thoroughly before using it in production.
Our Products are intended for sale to industrial and commercial customers. We request that Customers inspect and test our products before use and satisfy themselves as to
contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any warranty or merchantability or fitness, nor is protection from any
law of patent to be inferred. All patent rights are reserved. The exclusive remedy for all proven claims is replacement of our materials and in no event shall we be liable for
special, incidental or consequential damages
Last updated 17 December 2019 ISO 9001:2015 Registered Company
4051504102_TDS.pdf
World Class Coatings
Technology
515-XXX
TRANSPARENT TINTS:
ALL COLORS
____________________________________________________________________________________________
Dura Technologies. The materials in this product are chosen for their compatibility with
unsaturated polyester coatings.
Application:
1. Prior to use, determine the loading requirements for the specific application.
2. The tints should be added to the material under gentle agitation.
3. Mix the resin system for approximately 5 minutes before adding the tints.
4. For more information, refer to the SDS.
WARNING:
This material can affect the gel time and the viscosity of the resin system. Please evaluate this
material thoroughly before using it in production.
Our Products are intended for sale to industrial and commercial customers. We request that Customers inspect and test our products before use and satisfy themselves as to
contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any warranty or merchantability or fitness, nor is protection from any
law of patent to be inferred. All patent rights are reserved. The exclusive remedy for all proven claims is replacement of our materials and in no event shall we be liable for
special, incidental or consequential damages
Last updated 17 December 2019 ISO 9001:2015 Registered Company
4051504402_TDS.pdf
World Class Coatings
Technology
515-XXX
TRANSPARENT TINTS:
ALL COLORS
____________________________________________________________________________________________
Dura Technologies. The materials in this product are chosen for their compatibility with
unsaturated polyester coatings.
Application:
1. Prior to use, determine the loading requirements for the specific application.
2. The tints should be added to the material under gentle agitation.
3. Mix the resin system for approximately 5 minutes before adding the tints.
4. For more information, refer to the SDS.
WARNING:
This material can affect the gel time and the viscosity of the resin system. Please evaluate this
material thoroughly before using it in production.
Our Products are intended for sale to industrial and commercial customers. We request that Customers inspect and test our products before use and satisfy themselves as to
contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any warranty or merchantability or fitness, nor is protection from any
law of patent to be inferred. All patent rights are reserved. The exclusive remedy for all proven claims is replacement of our materials and in no event shall we be liable for
special, incidental or consequential damages
Last updated 17 December 2019 ISO 9001:2015 Registered Company
40410002XTF_TDS.pdf
Our Products are intended for sale to industrial and commercial customers. We request that Customers inspect and test our products before use and satisfy themselves as to
contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any warranty or merchantability or fitness, nor is protection from any
law of patent to be inferred. All patent rights are reserved. The exclusive remedy for all proven claims is replacement of our materials and in no event shall we be liable for
special , incidental or consequential damages
9/4/2020 ISO 9001:2015Registered Company
DURAKOTE GEL COATS
400 SERIES
TOOLING GEL COAT
World Class Coatings
Technology
____________________________________________________________________________________________
Durakote 400 Series Gel Coats are tooling gel coats for fiber glass mold manufacturing. Easy application and
good surface properties make these products suitable for a wide range of tooling applications. Available in clear,
black, red and green, all colors are heavy metal free. Dura-Kote tooling gel coat is also available in a high flex
version as clear (404-009) and green (406-009).
PERFORMANCE BENEFITS
High Gloss
Excellent Hardness
Excellent chemical and abrasion resistance
Minimum distortion
TYPICAL LIQUID GEL COAT PROPERTIES
Gel time @77F, 2% MEKP: 8.5 1.5mins
Viscosity @ 77F, 20RPM # spindle: 3200 250cps
Thixotropic Index: 5 plus
Weight per gallon: 8.8 lbs
Maximum VOC < 45.12%
Maximum HAPs < 40.8
(Local regulations vary. Consult your local AQMD to determine actual VOC in use)
CURED FILM PROPERTIES
Barcol Hardness: 34 +
HDT 200F +
USAGE GUIDELINES
Mix this product for at least 5 minutes at low speed prior to use
MEKP levels should be kept at 2%
Do not apply gel coats below 64F
Apply using airless spray at a the minimum practicable pressure
Film thickness must be between 15mils and 25mils in 2-3 passes with a short flash off time between passes
SHELF LIFE
This product is stable for three months from date of production when stored away from sunlight at no more than
77F. Extended storage will result in some drift in gel times and viscosity. Elevated temperatures will reduce shelf
life further