TECHNICAL DATA SHEET
SikaBiresin AP017 RR
(FORMERLY P-17 RR)
POLYESTER RESIN
REDUCER RESIN FOR P-17

DESCRIPTION
The SikaBiresin AP017 RR REDUCER RESIN is a polyester resin system with heat resistance of 446 F (230 C) developed to reduce
the viscosity of SikaBiresin AP017 (Formerly P-17) High Heat Resistant Filler Paste. SikaBiresin AP017 RR Reducer Resin can be
added to SikaBiresin AP017 Filler in varying amounts to “customize” the SikaBiresin AP017 Filler anywhere from a thin runny
paste to a sprayable consistency without altering the physical properties or the quick set work life. It is recommended to
experiment with 5% by weight addition or less to stay closer to the SikaBiresin AP017 Filler cured properties. The
SikaBiresin AP017 RR also performs very well in applications requiring a quick setting, high temperature polyester laminating resin.

PROPERTIES
High service temperature
Styrene-free
Exceptional adhesion
Impact and chemical resistant

TECHNICAL DATA SHEET
SikaBiresin AP017 RR
February 19, Version 02 /2019
2

PHYSICAL PROPERTIES
Composition POLYESTER
SikaBiresin AP017RR
BPO HARDENER MIXED
Mix ratio by weight
Mix ratio by volume at 25 C
100 2
Aspect Liquid Cream Paste Liquid
Viscosity (cps) 1,000
Color NOTE – Mixed color can be
varied with Cream BPO color

Clear Amber White
Red
Black

Specific gravity at 25 C lbs./gal
(g/cc)
ASTM D792 9.07
(1.09)
Pot Life at 25 C (102 g) (minutes) ASTM D2471 11

NOTE – SikaBiresin AP017 RR Can be used alone to thin P-17 or with 2% BPO cream hardener for laminating applications. BPO
cream hardener is not sold with the P-17 Reducer Resin.

TECHNICAL DATA SHEET
SikaBiresin AP017 RR
February 19, Version 02 /2019
3

PROCESSING

PROCESSING CONDITIONS
Thoroughly blend 100 parts resin with 2 parts hardener by weight for 1 to 1 minutes in clean
dry container

HANDLING PRECAUTIONS
Normal health and safety precautions should be observed when handling these products:
Ensure good ventilation.
Wear gloves, glasses and protective clothes.
For further information, please consult the Safety Data Sheets.

STORAGE CONDITIONS
Product shelf life of polyester resin is 12 months when stored in original unopened containers
between 65 77 F (15 25 C). Any opened can must be tightly closed. Product shelf life of BPO
hardener is 18 months when stored in original unopened containers between 65 77 F (15 25 C).
Any opened can must be tightly closed.

PACKAGING
Packaging information on request, please contact your local sales representative or find your local
contact on www.sikaadvancedresins.us

TECHNICAL DATA SHEET
SikaBiresin AP017 RR
February 19, Version 02 /2019
4

LEGAL NOTICE
The information, and, in particular, the recommendations relating to the application and end-use of
Sika products, are given in good faith based on Sika s current knowledge and experience of the products
when properly stored, handled and applied under normal conditions in accordance with Sika s
recommendations. In practice, the differences in materials, substrates and actual site conditions are
such that no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability
arising out of any legal relationship whatsoever, can be inferred either from this information, or from
any written recommendations, or from any other advice offered. The user of the product must test the
product s suitability for the intended application and purpose. Sika reserves the right to change the
properties of its products. The proprietary rights of third parties must be observed. All orders are
accepted subject to our current terms of sale and delivery. Users must always refer to the most recent
issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on
request.

CONTACT ADVANCED RESINS

GERMANY
Stuttgarter Stra e 139
72574 Bad Urach GERMANY
Tel.: (+49) 7 125 940 492
Fax. : (+49) 7 125 940 401
E-mail : tooling@de.sika.com
Website : www.sikaadvancedresins.de
FRANCE
ZI des B thunes – 15, Rue de l Equerre
95310 Saint-Ouen-l Aum ne
CS 40444
95005 CERGY PONTOISE Cedex FRANCE
Tel.: (+33) 1 344 034 60
Fax: (+33) 1 342 197 87
E-mail: advanced.resins@fr.sika.com
Website : www.sikaadvancedresins.fr
SPAIN
Pol gon Industrial Congost – Guardaagulles, 8
08520 LES FRANQUESES DEL VALLES SPAIN
Tel.: (+34) 932 25 16 20
E-mail: spain@axson.com
Website: www.sikaadvancedresins.es
ITALY
Via Morandi 15
21047 Saronno (Va) ITALY
Tel.: (+39) 02 9670 2336
Fax: (+39) 02 9670 2369
E-mail: axson@axson.it
Website: www.sikaadvancedresins.it

UNITED KINGDOM
Unit 15 Studlands Park Ind. Estate
Newmarket Suffolk, CB8 7AU UNITED KINGDOM
Tel.: (+44) 1638 660 062
Fax: (+44) 1638 665 078
E-mail: sales.uk@axson.com
Website: www.sikaadvancedresins.uk
SLOVAKIA
Tovarenska 49
95301 ZLATE MORAVCE SLOVAKIA
Tel: (+421) 376 422 526
Fax: (+421) 376 422 527
E-mail: axson.sk@axson.com
Web site: www.sikaadvancedresins.sk
UNITED STATES
30800 Stephenson Highway
Madison Heights, Michigan 48071 USA
Tel.: (+1) 248 588-2270
Fax: (+1) 248 577-0810
E-mail: axsonmh@axson.com
Web site: www.sikaadvancedresins.us
MEXICO
Ignacio Ram rez #20
Despacho 202 Col. Tabacalera
C.P. 06030 CDMX MEXICO
Tel.: (+52) 55 5264 4922
Fax: (+52) 55 5264 4916
E-mail: marketing@axson.com.mx
Website: www.sikaadvancedresins.mx

CHINA
N 53 Tai Gu Road
Wai Gao Qiao
Free Trade Zone, Pudong
200131 Shanghai CHINA
T l.: (+86) 21 5868 3037
Fax: (+86) 21 5868 2601
E-mail: marketing.china@axson.com
Website: www.sikaadvancedresins .cn
JAPAN
2-5-12 Onishi Okazaki Aichi
444-0871 JAPAN
Tel.: (+81) 564 26 2591
Fax: (+81) 564 26 2593
E-mail: sales.japan@axson.com
Website: www.sikaadvancedresins.jp
INDIA
Office n 8, Building Symphony C – 3rd Floor
Range Hills Road
Bhosale Nagar
PUNE 411 020 INDIA
Tel: (+ 91) 20 25 56 07 10
Fax: (+ 91) 20 25 56 07 12
E-mail: info.india@axson.com
Website: www.sikaadvancedresins.in

1
TECHNICAL DATA SHEET
SikaBiresin AP014
February 19, Version 02 /2019

1
TECHNICAL DATA SHEET
SikaBiresin AP014
(FORMERLY P-14)
POLYESTER FILLER S YSTEM
MACHINABLE / RIGID

DESCRIPTION
The most versatile of all set-fast filler pastes, AP014 ULTRA FILLER is a two component filler system which
yields a smooth, creamy, thixotropic and workable paste with superior handling, set-fast characteristics
and dimensional stability. Once applied it forms a rigid, strong surface which can be machined, sanded,
filed or scraped to a feather edge. A P014 adheres and bonds to fiberglass, SMC, RIM, BMC, Graphite,
Kevlar

and other types of composites as well as aluminum, steel, grey iron, copper, plaster, models,
patterns and other substrates. AP014 offers the industry manufacturer a wide variety of applications for
bonding, filling, sealing and finishing with optimum physical properties. AP014 ULTRA FILLER can be
applied without pin-holing and exhibits no shrink or sink after curing. It accepts virtually all types of
finishes e.g., lacquer, enamel, polyurethane, epoxy, etc., without any special surface preparation. It is a
“no bleed out” system after finishing or if covered with a decorative film. Its high quality, coupled with
the set-fast feature offers industry substantial savings in time and labor plus top quality in the finished
product. AP014 can be used in areas of final fabrication, production, tooling, model & pattern making,
repair operations and in many other applications. Typical applications include: filling composites surface
porosity, honeycomb panel edge filler, bonding loose pieces and details, vacuum mold repair and
modifications, urethane mold repairs and modifications, FRP composite repairs, pattern repairs and
fillets, core box repairs and modifications, void and porosity filling, router fixture repairs, crack, dent and
crevice repair, temporary holding fixtures, filling cloth impressions in pre-preg, non-conductive barrier
potting, RIM/SMC/BMC surface filler, bonding inserts/hangers, urethane part repair, potting stripped
threads, renewing worn surfaces and many others.

PROPERTIES
Very quick setting
Comes in white and gray colors
Dimensionally stable

Excellent finishing and machinability
Easy to use
Good adhesion

TECHNICAL DATA SHEET
SikaBiresin AP014
February 19, Version 02 /2019

2
PHYSICAL PROPERTIES
Composition POLYESTER
SikaBiresin AP 014
BPO HARDENER
BPO
MIXED
Mix ratio by weight
Mix ratio by volume at 25 C
100 2
Aspect Paste Cream Paste Paste
Color NOTE – Mixed color can be
varied with Cream BPO color
(As a mixing aid/indicator and
final color choice)
White
Gray

White
Red
Black

Viscosity at 25 C (cPs) BROOKFIELD LVT Paste
Specific gravity at 25 C lbs./gal
(g/cc)
ASTM D792 13.4
(1.61)
10.0
(1.20)
13.30
(1.60)
Pot Life at 25 C (102 g) (minutes) ASTM D2471 4.0 6.0

MECHANICAL PROPERTIES at 23 C
(1)

Hardness (Shore D) ASTM D-2240 86
Water absorption 24 hr/R.T. soak (%) ASTM D-570 0.16
Adhesive pull strength (psi)
Aluminum
Polyester filler
Mahogany
Epoxy glass laminate
ASTM D-4541

2,940
1,717
1,459
753
(1)

Average values obtained on standard specimens / Cured 7 days at 25 C

CHEMICAL RESISTANCE GUIDE
AP014 Ultra Filler combines saturated and unsaturated Polyester resins of medium to high reactivity. As an aid to the user,
chemical resistance evaluations were conducted using a modification of ASTM 0543-60T.

TESTING PROCEDURE
Samples nominally sized at 1/2″ x 1″ x 4″ were immersed halfway in 4 ounces of reagent and stored for 12 months at ambient
temperature. Reagents were swirled monthly, and specimens were rated every 4 weeks.

RATING RESULTS
Excellent, No Visible Attack Good, Very Slight Attack Not Recommended
Benzene
Gasoline
Methanol
Mineral Spirits
Water (Distilled)
Acetic Acid (5%)
Citric Acid
Hydrochloric Acid (10%)
Nitric Acid (10%)
Sodium Hydroxide (5%)
Sulfuric Acid (10%)
Acetone

TECHNICAL DATA SHEET
SikaBiresin AP014
February 19, Version 02 /2019

3

PROCESSING

PROCESSING CONDITIONS
Thoroughly blend 100 parts resin with 2 parts hardener by weight for 1 to 1 minutes in clean
dry container or on a clean dry surface.
Carefully scrape the surfaces while blending to ensure complete mixing and uniformity.

SURFACE PREPARATION and APPLICATION
The area to be filled or repaired should be thoroughly cleaned, roughened, cleaned again
and dried to allow for the best possible adhesion.
The mixed A P014 should be buttered into the area, avoiding trapping air during application.
After curing to a tack-free state, the material can be sanded and finished as needed.

MIXING INSTRUCTIONS
Stir contents of can thoroughly using a spatula or putty knife. Place the required amount of filler
and cream hardener on a disposable clean surface. Mix 100 parts paste to 2 parts BPO cream
hardener by weight; i.e. approximatly size of golf ball (paste) to a two inch strip of BPO catalyst. Set
up time of mix at room temperature will be 5-10 minutes. After 15-20 minutes the filler may be
filed or sanded to final finish.

HANDLING PRECAUTIONS

Normal health and safety precautions should be observed when handling these products :
Ensure good ventilation.
Wear gloves, glasses and protective clothes.
For further information, please consult the Safety Data Sheets.

STORAGE CONDITIONS

Product shelf life of polyester resin is 12 months when stored in original unopened containers
between 65 77 F (15 25 C). Any opened can must be tightly closed. Product shelf life of BPO
hardener is 18 months when stored in original unopened containers between 65 77 F (15 25 C).
Any opened can must be tightly closed.
Polyester resin contains filler which has the potential to separate in time, please re-homogenize
prior to use.

PACKAGING
Packaging information on request, please contact your local sales representative or find your local
contact on www.sikaadvancedresins.us

TECHNICAL DATA SHEET
SikaBiresin AP014
February 19, Version 02 /2019

4

LEGAL NOTICE

The information, and, in particular, the recommendations relating to the application and end-use of
Sika products, are given in good faith based on Sika s current knowledge and experience of the products
when properly stored, handled and applied under normal conditions in accordance with Sika s
recommendations. In practice, the differences in materials, substrates and actual site conditions are
such that no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability
arising out of any legal relationship whatsoever, can be inferred either from this information, or from
any written recommendations, or from any other advice offered. The user of the product must test the
product s suitability for the intended application and purpose. Sika reserves the right to change the
properties of its products. The proprietary rights of third parties must be observed. All orders are
accepted subject to our current terms of sale and delivery. Users must always refer to the most recent
issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on
request.

CONTACT ADVANCED RESINS
GERMANY
Stuttgarter Stra e 139
72574 Bad Urach GERMANY
Tel.: (+49) 7 125 940 492
Fax. : (+49) 7 125 940 401
E-mail : tooling@de.sika.com
Website : www.sikaadvancedresins.de
FRANCE
ZI des B thunes – 15, Rue de l Equerre
95310 Saint-Ouen-l Aum ne
CS 40444
95005 CERGY PONTOISE Cedex FRANCE
Tel.: (+33) 1 344 034 60
Fax: (+33) 1 342 197 87
E-mail: advanced.resins@fr.sika.com
Website : www.sikaadvancedresins.fr
SPAIN
Pol gon Industrial Congost – Guardaagulles, 8
08520 LES FRANQUESES DEL VALLES SPAIN
Tel.: (+34) 932 25 16 20
E-mail: spain@axson.com
Website: www.sikaadvancedresins.es
ITALY
Via Morandi 15
21047 Saronno (Va) ITALY
Tel.: (+39) 02 9670 2336
Fax: (+39) 02 9670 2369
E-mail: axson@axson.it
Website: www.sikaadvancedresins.it
UNITED KINGDOM
Unit 15 Studlands Park Ind. Estate
Newmarket Suffolk, CB8 7AU UNITED KINGDOM
Tel.: (+44) 1638 660 062
Fax: (+44) 1638 665 078
E-mail: sales.uk@axson.com
Website: www.sikaadvancedresins.uk
SLOVAKIA
Tovarenska 49
95301 ZLATE MORAVCE SLOVAKIA
Tel: (+421) 376 422 526
Fax: (+421) 376 422 527
E-mail: axson.sk@axson.com
Web site: www.sikaadvancedresins.sk
UNITED STATES
30800 Stephenson Highway
Madison Heights, Michigan 48071 USA
Tel.: (+1) 248 588-2270
Fax: (+1) 248 577-0810
E-mail: axsonmh@axson.com
Web site: www.sikaadvancedresins.us
MEXICO
Ignacio Ram rez #20
Despacho 202 Col. Tabacalera
C.P. 06030 CDMX MEXICO
Tel.: (+52) 55 5264 4922
Fax: (+52) 55 5264 4916
E-mail: marketing@axson.com.mx
Website: www.sikaadvancedresins.mx
CHINA
N 53 Tai Gu Road
Wai Gao Qiao
Free Trade Zone, Pudong
200131 Shanghai CHINA
T l.: (+86) 21 5868 3037
Fax: (+86) 21 5868 2601
E-mail: marketing.china@axson.com
Website: www.sikaadvancedresins .cn
JAPAN
2-5-12 Onishi Okazaki Aichi
444-0871 JAPAN
Tel.: (+81) 564 26 2591
Fax: (+81) 564 26 2593
E-mail: sales.japan@axson.com
Website: www.sikaadvancedresins.jp
INDIA
Office n 8, Building Symphony C – 3rd Floor
Range Hills Road
Bhosale Nagar
PUNE 411 020 INDIA
Tel: (+ 91) 20 25 56 07 10
Fax: (+ 91) 20 25 56 07 12
E-mail: info.india@axson.com
Website: www.sikaadvancedresins.in

PRODUCT BULLETIN

www.axson-technologies.com 800.344.7776 axsonmh@axson.com
31200 Stephenson Hwy Madison Heights, MI 48071 Ph 248.588.2270 Fax 248.588.5909

DESCRIPTION:

Fast Patch Paste TCC-5220 A/B is a two-part system designed to quickly make repairs or modifications to the PP-1052 Pattern Plank

.
This material is available in convenient self-mixing cartridges for ease of use. A dispensing gun must be used to dispense this material.
Patch Paste TCC-5220 A/B will cure rapidly and can be machined or sanded in approximately 15 – 20 minutes.

TYPICAL HANDLING CHARACTERISTICS @ 77 F (25 C)

Mix Ratio (by weight or volume) ………………………………………………………………….. Resin TCC-5220A ……………………….100 parts
………………………………………………………………………………………………………………. Hardener TCC-5220B ………………….100 parts
Pot Life (50 gram mass) …………………………………………………………………………………………………………………………………3 minutes
Hardness ……………………………………………………………………………………………………………………………………………………..80 – 85 Shore D
Viscosity ………………………………………………………………………………………………….. Resin TCC-5220A ……………………….26,000 cps
………………………………………………………………………………………………………………. Hardener TCC-5220B ………………….20,000 cps
………………………………………………………………………………………………………………. Mixed Viscosity …………………………..Paste
Specific Gravity …………………………………………………………………………………………………………………………………………….1.03g/cc
Color ……………………………………………………………………………………………………….. Resin TCC-5220A ……………………….Brown
………………………………………………………………………………………………………………. Hardener TCC-5220B ………………….Red
………………………………………………………………………………………………………………. Mixed Color ………………………………..Red
Machinability …………………………………………………………………………………………………………………………………………………Good
Time to Machine or Sand (depending on temperature) ……………………………………………………………………………………….15 – 20 minutes
Shelf Life (in original unopened containers) ………………………………………………….. TCC-5220A/TCC-5220B ………………2 years

Standard Size Available: 50ml cartridge

SANITARY PRECAUTIONS:
Do not take internally. Avoid prolonged breathing of vapors. Work in a well-ventilated area. Avoid skin contact. Protective gloves
should be worn. If contact occurs: wash skin with soap and water. Avoid eye contact. If contact occurs: rinse well with water for 15
minutes, contact physician.

STORAGE AND HANDLING:
To avoid moisture contamination, with each new nozzle purge small amount of material. Store at room temperature.

TCC-5220 Tech/Revised 1/30/15
Supersedes 6/20/14

The information contained in this technical data sheet results from research and tests conducted in our laboratories under precise conditions. Seller
cannot anticipate all conditions under which seller s products, or the products of other manufacturers in combination with seller s products, may be used.
It is the responsibility of the user to determine the suitability of the Axson Technologies products, under their own conditions, before commencing with
the proposed application. In no event shall Axson Technologies, Inc. be liable for any direct, indirect, punitive, incidental, special, and/or consequential
damages, to property or life, whatsoever arising out of or connected with the use or misuse of our products.
TCC-5220 A/B
FAST PATCH PASTE
FOR PP-1052
PATTERN PLANK

1
TECHNICAL DATA SHEET
TCC-410
February 19, Version 01 /2021

1
TECHNICAL DATA SHEET
TCC-410
SURFACE/MASS CASTING SYSTEM
IMPACT RESISTANT

DESCRIPTION
Epoxy Resin TCC-410 is an aluminum filled system designed for high-impact resistance. This system can be surface
cast to metal or other low-cost cores or it may be mass casted. Depending on thickness of cast, a choice of hardeners
is provided to control exothermic heat and shrinkage. Applications for this system include casting surfaces on
prototype stamping dies or mass casting applications where high-impact resistance is desired.

APPLICATIONS
Casting surfaces on prototype stamping dies
Mass casting applications

TECHNICAL DATA SHEET
TCC-410
February 19, Version 01 /2021

2
PHYSICAL PROPERTIES

Thickness of Cast > Surface Cast – 1 Mass Cast 1 – 4 Mass Cast 4 – 10
Hardener Selection TCC-104 TCC-104-5 TCC-105
Mix Ratio (parts by weight):
Resin TCC-410 100 parts 100 parts 100 parts
Hardener 10 parts 10 parts 10 parts
Pot Life (500 gram mass) 60 minutes 100 minutes 2 – 3 hours
Peak Exotherm 200 F (93 C)
Peak Operating Temperature 180 F (82 C) 210 F (99 C) 240 F (116 C)
Cure Time 8 – 12 hours 18- 36 hours 48 – 72 hours

TYPICAL PHYSICAL PROPERTIES with TCC-104 H @ 77 F (25 C) Cured 7 days @ R.T.
Specific Gravity (g/cc) 1.65
Mixed Viscosity – (cps & mPa.s)_ 6,000
Cured Color – Visual Aluminum – Gray
Hardness – (Shore D) 84
Linear Shrinkage (in/in) 0.0015
Notched Izod Impact Strength – (ft lbs/in) 8.5
Tensile Strength – psi (MPa) 7,000 (48)
Shelf Life (in original unopened containers) TCC-401/TCC-104, TCC-104-5, or TCC-105
2
years

HANDLING PRECAUTIONS
Normal health and safety precautions should be observed when handling these products:
Ensure good ventilation.
Wear gloves, glasses and protective clothes.
For further information, please consult the Safety Data Sheets.

STORAGE CONDITIONS
This product has a shelf life of 24 months for the resin and hardener as indicated by the
expiration date on the container when stored in original unopened containers.

PACKAGING
Packaging information on request, please contact your local sales representative or find your
local contact on www.sikaadvancedresins.us

LEGAL NOTICE

The information, and, in particular, the recommendations relating to the application and
end-use of Sika products, are given in good faith based on Sika s current knowledge and
experience of the products when properly stored, handled and applied under normal
conditions in accordance with Sika s recommendations. In practice, the differences in
materials, substrates and actual site conditions are such that no warranty in respect of
merchantability or of fitness for a particular purpose, nor any liability arising out of any legal
relationship whatsoever, can be inferred either from this information, or from any written
recommendations, or from any other advice offered. The user of the

TECHNICAL DATA SHEET
TCC-410
February 19, Version 01 /2021

3
product must test the product s suitability for the intended application and purpose. Sika
reserves the right to change the properties of its products. The proprietary rights of third
parties must be observed. All orders are accepted subject to our current terms of sale and
delivery. Users must always refer to the most recent issue of the local Product Data Sheet
for the product concerned, copies of which will be supplied on request.

CONTACT
UNITED STATES
Sika Corporation
30800 Stephenson Highway
Madison Heights, Michigan 48071 USA
Tel.: (+1) 248 588-2270
Fax: (+1) 248 577-0810
E-mail: advanced.resins@us.sika.com
Website: www.sikaadvancedresins.us

TC-4485 A/B
IRON-FILLED EPOXY MASS CASTING SYSTEM

TC-4485 A/B is a room temperature curing, mass castable epoxy resin system that produces a tough, dense, low shrink solid
material with fine detail reproduction. TC-4485 A/B is designed for single-pour castings up to 3″ thick, or for thicker castings up
to 8″ using a stage pour procedure.

Slower reacting system designed for thicker casts Improved viscosity for easier pouring

TYPICAL PRODUCT USES :
Molds Patterns
Cast Parts Form Dies

PHYSICAL PROPERTIES TEST METHOD TEST RESULTS
Hardness, Shore D ASTM D2240 85 2
Density (g/cc) ASTM D792 2.1
Cubic Inches per Pound N/A 13.1
Tensile Modulus (psi) ASTM D638 5.2 x 10
7

Flexural Strength (psi) ASTM D790 9,450
Flexural Modulus (psi) ASTM D790 3.2 x 10
5

Izod Impact (ft-lb/in) ASTM D256 2.0
Shrinkage (in/in) ASTM D2566 <0.001 Compressive Strength (psi) ASTM D695 13,320 Coefficient of Thermal Expansion (in/in/F ) ASTM D3386 3.0 x 10 -5 HANDLING PROPERTIES Part A Part B Mix Ratio by weight 100 8 Mix Ratio by volume 100 15 Specific Gravity @ 77 F (25 C) 1.80 0.99 Color Black Amber Viscosity (cps) @ 77 F (25 C) Brookfield 278,000 70 Mixed Viscosity (cps) @ 77 F (25 C) Brookfield 42,500 Work Time, 1 lb. mass @ 77 F (25 C) 3 0.5 hours Demold Time @ 77 F (25 C) 16 24 hours Cure Time @ 77 F (25 C) 3 5 days Properties above are typical and not for specifications. EPOXY RESIN SYSTEMS Dedicated to QUALITY, SERVICE, SAFETY, and INNOVATION TC-4485 A/B Page 2 of 2 Date: 12/18/2015 For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929 NON-WARRANTY "Except for a warranty that materials substantially comply with the data presented in Manufacturer's latest bulletin describing the product (the basis for this substantial compliance is to be determined by the standard quality control tests generally performed by Manufacturer), all materials are sold "AS IS" and without any warranty express or implied as to merchantability, fitness for a particular purpose, patent, trademark or copyright infringement, or as to any other matter. In no event shall Manufacturer's liability for damages exceed Manufacturer's sale price of the particular quantity with respect to which damages are claimed." Quality Management System Registered to ISO 9001:2008 STORAGE: Store at ambient temperatures, 65-80 F (18-27 C). Unopened containers will have a shelf life of 12 months from date of shipment when properly stored at recommended temperatures. Purge opened containers with dry nitrogen before re-sealing. PACKAGING Part A Part B Cubic Inches per Kit 5-Gallon Kits 60 lbs. 5 lbs. 852 SAFETY PRECAUTIONS : Use in a well-ventilated area. Avoid contact with skin using protective gloves and protective clothing. Repeated or prolonged contact on the skin may cause an allergic reaction. Eye protection is extremely important. Always use approved safety glasses or goggles when handling this product. IF CONTACT OCCURS : Skin: Immediately wash with soap and water. Remove contaminated clothing and launder before reuse. It is not recommended to remove resin from skin with solvents. Solvents only increase contact and dry skin. Seek qualified medical attention if allergic reactions occur. Eyes: Immediately flush with water for at least 15 minutes. Call a physician. Ingestion: If swallowed, call a physician immediately. Remove stomach contents by gastric suction or induce vomiting only as directed by medical personnel. Never give anything by mouth to an unconscious person. Refer to the Material Safety Data Sheet before using this product. TC-4485 Part A SDS TC-4485 Part B SDS

TC-1614 A/B
EPOXY PENETRATING
SEALING AND COATING RESIN SYSTEM

TC-1614 A/B is an unfilled, low viscosity epoxy resin system. It is designed to seal porous to semi-porous substrates developing
remarkable strength. TC-1614 A/B also has exceptional adhesive characteristics and is capable of high temperatures.

Easy to use and apply Withstands temperatures up to 350 F (177 C)
Penetrates and seals porous surfaces with excellent adhesion Can be pigmented for color enhancement
Works great for sealing 3D Printed parts Recommended by several 3D Printer Manufacturers

PHYSICAL PROPERTIES TEST METHOD TEST RESULTS
Hardness, Shore D ASTM D2240 85 2
Density (g/cc) ASTM D792 1.14
Cubic Inches per Pound N/A 25.1
Color/Appearance Visual Yellow Opaque
Tensile Strength (psi) ASTM D638 9,500
Tensile Modulus (psi) ASTM D638 320,000
Elongation (%) ASTM D638 5
Flexural Strength (psi) ASTM D790 12,600
Flexural Modulus (psi) ASTM D790 380,000
Shrinkage (in/in) linear 12 x x 0.008
Izod Impact, notched (ft-lb/in) ASTM D256 0.44
Reported physical properties based on elevated temperature cured test specimens.

HANDLING PROPERTIES Part A Part B
Mix Ratio by weight 100 20
Mix Ratio by volume 100 23
Specific Gravity @ 77 F (25 C) 1.13 0.98
Color Colorless Amber
Viscosity (cps) @ 77 F (25 C) Brookfield 550 250
Mixed Viscosity (cps) @ 77 F (25 C) Brookfield 600
Work Time, 100g mass @ 77 F (25 C) 2 hours
Tack Free
10 12 hours @ 77 F (25 C)
5 hours @ 120 F (48.9 C)
Properties above are typical and not for specifications.
*Application Procedures see page 3

EPOXY RESIN SYSTEMS
Dedicated to QUALITY, SERVICE, SAFETY, and INNOVATION
An ISO-9001 Certified company

TC-1614 A/B Page 3 of 3 Date: 09/29/2020
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929

NON-WARRANTY “Except for a warranty that materials substantially comply with the data presented in Manufacturer’s latest bulletin describing the product (the basis for this substantial
compliance is to be determined by the standard quality control tests generally performed by Manufacturer), all materials are sold “AS IS” and without any warranty express or implied as
to merchantability, fitness for a particular purpose, patent, trademark or copyright infringement, or as to any other matter. In no event shall Manufacturer’s liability for damages exceed
Manufacturer’s sale price of the particular quantity with respect to which damages are claimed.”

POST CURING:

All physical property results are based upon post-curing this system. The following procedure provides the best results:

150 F (66 C) for 1.5 to 2 hours
250 F (121 C) for 2 hours
300 F (149 C) for 1 hour
350 F (177 C) for 1 hour

Allow to cool in the oven. This procedure provides further stabilization and eliminates possible thermal shocks for cavity tools that are
temporarily clamped together for curing purposes.

STORAGE:

Store at ambient temperatures, 65-80 F (18-27 C). Unopened containers will have a shelf life of 12 months from date of shipment
when properly stored at recommended temperatures. Purge opened containers with dry nitrogen before re-sealing.

PACKAGING Part A Part B
Cubic Inches
per Kit
Quart Kits 2 lbs. 7 oz. 61
Gallon Kits 9 lbs. 1.8 lbs. 271
5-Gallon Kits 40 lbs. 8 lbs. 1,205

SAFETY PRECAUTIONS :

Use in a well-ventilated area. Avoid contact with skin using protective gloves and protective clothing. Repeated or prolonged contact
on the skin may cause an allergic reaction. Eye protection is extremely important. Always use approved safety glasses or goggles
when handling this product.

IF CONTACT OCCURS :

Skin: Immediately wash with soap and water. Remove contaminated clothing and launder before reuse. It is not recommended
to remove resin from skin with solvents. Solvents only increase contact and dry skin. Seek qualified medical attention if
allergic reactions occur.
Eyes: Immediately flush with water for at least 15 minutes. Call a physician.
Ingestion: If swallowed, call a physician immediately. Remove stomach contents by gastric suction or induce vomiting only as
directed by medical personnel. Never give anything by mouth to an unconscious person.

Refer to the Material Safety Data Sheet before using this product.

WARNING: This product can expose you to chemicals including Ethylbenzene and 4,4 -Isopropylidenediphenol, which are known to
the State of California to cause cancer, birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

TC-1614 A/B Page 3 of 3 Date: 09/29/2020
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929

NON-WARRANTY “Except for a warranty that materials substantially comply with the data presented in Manufacturer’s latest bulletin describing the product (the basis for this substantial
compliance is to be determined by the standard quality control tests generally performed by Manufacturer), all materials are sold “AS IS” and without any warranty express or implied as
to merchantability, fitness for a particular purpose, patent, trademark or copyright infringement, or as to any other matter. In no event shall Manufacturer’s liability for damages exceed
Manufacturer’s sale price of the particular quantity with respect to which damages are claimed.”
Product Application Procedure for 3D Printed Parts

Material: TC-1614 Epoxy

Purpose of Procedure: To impregnate rigid, porous 3D Printed Parts with epoxy. Infusing epoxy into the surface is a
beneficial procedure to increase strength, improve handling qualities and in some parts, improve aesthetics. Some
systems will absorb more material than others.

Procedure:
Pre-warm A&B material in separate containers to 90 -100 F maximum (32 -37 C max) in a temperature
controlled industrial oven. This will help to lower the viscosity and increase the absorption rate of epoxy into
the part (never use a household oven that may be in contact with food).
You can also pre-warm the 3D printed part to aid in epoxy infiltration. 100 -120 F (37 -49 C) is a good range
but refer to your 3D printed material recommendations for heat resistance in an effort to avoid distortion.
Place a small 3D Printed Part into a self-sealing (zipper lock) plastic bag and fill with an appropriate amount
of epoxy. A bag that is too large will require more volumetric amounts of epoxy. Squeeze out as much of the
extra air in the bag to assure part is fully submerged and coated with epoxy then seal bag.
Allow the part to soak in the epoxy for roughly 20-25 minutes. A recommended optional procedure would be
to place bag with soaking 3D Printed part into 100 -120 F (37 -49 C) oven in a leak-proof, metal container,
and allow to soak for 15-20 minutes. Check part at 5 minute intervals to monitor viscosity levels and for any
exothermic reaction. Larger batches of mixed epoxy will have a shorter reaction time.
Once part has soaked for allotted time, pull part out of bag and drain excess epoxy off of part.
For larger parts, mix enough A&B together so you have sufficient material to brush an even coat over the part.
Continue brushing drips and runs to keep part coated for 20-30 minutes. Then drain off excess epoxy and
wipe down surface with clean, dry paper towels. Avoid using any solvents since it will affect the curing
properties.
*Note that mixing a large mass of epoxy can produce an increase in chemical reaction shortening work time
and increasing exotherm (heat) as it sits. Do not leave a large, concentrated mass of epoxy in a container
unattended. After soaking the part, it may be best to split up a large batch (over 200-300g) by draining the
bag into 2-3 separate small containers and allow to harden.
Hang part with wire over a cup or bucket to allow continued drainage of excess epoxy. Wipe off any areas of
pooled epoxy with a gloved finger or brush. Monitor any sags or drips for the next hour or until epoxy has
gelled.
You can expedite curing of the epoxy in an oven at 100 -120 F (37 -49 C) and promote better physical
properties of the finished material. You can also allow the epoxy to cure at room temperature but an elevated
post cure will achieve the best results.

TC-1570 A/B
WHITE EPOXY SURFACE COAT

TC-1570 A/B is a general-purpose white epoxy surface coat that can be used in conjunction with epoxy or polyurethane resin
systems. TC-1570 A/B is noted for its ease of application and its ability to hang on vertical surfaces without sag or runoff.

PHYSICAL PROPERTIES TEST METHOD RESULTS
Hardness, Shore D ASTM D2240 90 2
Density (g/cc) ASTM D792 1.92
Cubic Inches per Pound N/A 13.7
Color/Appearance Visual White Opaque
Flexural Strength (psi) ASTM D790 8,100
Flexural Modulus (psi) ASTM D790 9.5 x 10
5

Heat Deflection Temperature @ 66 psi ASTM D648 220 F (104.4 C)
Heat Deflection Temperature @ 264 psi ASTM D648 217 F (102.8 C)

HANDLING PROPERTIES Part A Part B
Mix Ratio by weight 100 8
Specific Gravity @ 77 F (25 C) 2.1 1.08
Mixed Viscosity (cps) @ 77 F (25 C) Brookfield Brushable
Work Time, 100g mass @ 77 F (25 C) 15 20 minutes
Cure Schedule 8 12 hours
Properties above are typical and not for specifications.

STORAGE:

Store at ambient temperatures, 65-80 F (18-27 C). Unopened containers will have a shelf life of 12 months from date of
shipment when properly stored at recommended temperatures. Purge opened containers with dry nitrogen before re-sealing.

PACKAGING Part A Part B
Square Inches
per Kit
(Coverage @ 1/16 thick)
Quart Kits 3 lbs. 4 oz. 712
Gallon Kits 10 lbs. 13 oz. 2,370
5-Gallon Kits 45 lbs. 3.6 lbs. 10,653

EPOXY RESIN SYSTEMS
Dedicated to QUALITY, SERVICE, SAFETY, and INNOVATION
An ISO-9001 Certified company

TC-1570 A/B Page 2 of 2 Date: 02/13/2020
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-892

NON-WARRANTY “Except for a warranty that materials substantially comply with the data presented in Manufacturer’s latest bulletin describing the product (the basis for this substantial
compliance is to be determined by the standard quality control tests generally performed by Manufacturer), all materials are sold “AS IS” and without any warranty express or implied as
to merchantability, fitness for a particular purpose, patent, trademark or copyright infringement, or as to any other matter. In no event shall Manufacturer’s liability for damages exceed
Manufacturer’s sale price of the particular quantity with respect to which damages are claimed.”

SAFETY PRECAUTIONS :

Use in a well-ventilated area. Avoid contact with skin using protective gloves and protective clothing. Repeated or
prolonged contact on the skin may cause an allergic reaction. Eye protection is extremely important. Always use approved
safety glasses or goggles when handling this product.

IF CONTACT OCCURS :

Skin: Immediately wash with soap and water. Remove contaminated clothing and launder before reuse. It is not
recommended to remove resin from skin with solvents. Solvents only increase contact and dry skin. Seek
qualified medical attention if allergic reactions occur.
Eyes: Immediately flush with water for at least 15 minutes. Call a physician.
Ingestion: If swallowed, call a physician immediately. Remove stomach contents by gastric suction or induce vomiting
only as directed by medical personnel. Never give anything by mouth to an unconscious person.

Refer to the Material Safety Data Sheet before using this product.

WARNING: This product can expose you to chemicals including 4,4 -Isopropylidenediphenol, which are known to
the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to
www.P65Warnings.ca.gov.

TC-1570 Part A SDS TC-1570 Part B SDS

PDS-Spabond340LV(HT)-12-0219 1

SPABOND 340LV HT
HIGH TG STRUCTURAL EPOXY ADHESIVE

Reduced component weights; lower density when compared to glass filled
adhesives
Higher thermal performance & fast cure progression
High strength and toughness industrial adhesive
Excellent gap filling properties
Designed for cartridge and mixing machine dispense
Three hardener speeds give a range of working times / clamp times
Resin & hardener are pigmented to give a visual indication of mix quality
DNV-GL Certified Formats Available

INTRODUCTION
Spabond 340 LV HT is a high performance adhesive designed for bonding large structures such as yacht hulls
and wind turbine blades. It is a cost-effective system with good thermal and mechanical properties.
The formulation gives high thermal performance and allows fast curing, making this product ideal for bonding large
composite structures where minimising cure time and increasing productivity is of value.
The components are pigmented to give a visual indication of mix quality, which is a useful feature when mixing by hand or
with a machine. The system has a simple 2:1 mix ratio by volume.
Spabond 340LV HT is available in cartridges, straight-sided pails and 205 litre drums for machine mixing and dispense.
SYSTEM 20 C POT-LIFE (500 G, MIXED IN AIR)* 20 C CLAMP TIME* PAGE
S
pabond

340LV

Product Information, Instructions for Use and Health & Safety 2
Fast (HT) 16 minutes 3 hours 50 minutes 3
Slow (HT) 45 minutes 17 hours 40 minutes 4
Extra Slow (HT) 2 hours 20 minutes 24 hours 5
*working time properties are highly subjective to ambient conditions and should be used an approximate guideline for all Spabond 340 systems

PDS-Spabond340LV(HT)-12-0219 2

PRODUCT INFORMATION
The product is available in a number of formats please contact
your local customer support or download the latest product
catalogue available on www.gurit.com.

PRODUCT DESCRIPTION STATUS CERTIFICATION
Spabond 340LV Resin and HT Hardeners Approved
DNV-GL
TAK00001H8

TRANSPORT & STORAGE
The resin and hardeners should be kept in securely closed containers during transport
and storage. Any accidental spillage should be soaked up with sand, sawdust, cotton
waste or any other absorbent material. The area should then be washed clean (see
appropriate Safety Data Sheet). Adequate long term storage conditions will result in a
shelf life of 2 years for both the resin and hardeners. Storage should be in a warm dry place out of direct sunlight and protected from frost.
The storage temperature should be kept constant between 10 C and 25 C, cyclic fluctuations in temperature can cause crystallization.
Containers should be firmly closed. Hardeners, in particular, will suffer serious degradation if left exposed to air.
For more information on crystallization please refer to the Adhesives section on the Gurit website. (www.gurit.com)
COMPONENT UNITS 10 25 C
Spabond 340LV Resin months 24
Spabond 340 HT Hardeners months 24
INSTRUCTIONS FOR USE
The product is optimised for use at 15 – 25 C. At lower temperatures the components thicken and may eventually become unworkable. To
ensure accurate mixing and good workability pre-warm the resin & hardener as well as the surfaces to be bonded before use.
SURFACE PREPARATION
Before using the product ensure that surfaces to be bonded are clean, dry and dust-free. Prepare all surfaces by abrading with medium grit
paper or other suitable abrasive, remove dust then wipe with acetone.
Metals – requires a chemical pre-treatment to create the best bond. Please contact Gurit for a Guide to Surface Preparation and Pre-treatments.
Polyester or vinylester – ensure laminates are fully cured before bonding, then prepare as above.
Epoxy laminates – it is recommended to use a suitable Peel Ply as the last stage in their manufacture, otherwise prepare as above. Trials may
be required to test Peel Ply suitability.
Ferrocement – etch with 5% solution of hydrochloric acid, wash with fresh water, then dry.
Timber – sand with abrasive paper across grain. Degrease oily timber with a fast evaporating solvent (e.g. acetone). For resinous or gummy
timber, etch with 2% caustic soda solution, wash off with fresh water and dry.
MIXING & HANDLING
Gurit recommends mixing machine dispense. If mixing by hand, mix thoroughly for at least one minute, paying particular attention to the sides
and bottom of the mixing vessel, to ensure no streaks remain. Once fully mixed the adhesive should have a uniform colour. Use from pot quickly
to maximise resin working life.
CARTRIDGE USE
If dispensing product from a two component cartridge, first prime the cartridge by dispensing slowly until both resin and hardener are at the
outlet of the cartridge. Secondly, clean the outlet and attach the mixing head. When starting a new cartridge, dispense and discard a small
amount of adhesive (typically the length of a mix head) prior to applying adhesive to the substrate, in order to ensure thorough mixing of the
system. If using a pneumatic gun, regulate supply air pressure to a maximum of 4 Bar. Relieve the pressure on the cartridge after use.
HEALTH AND SAFETY
The following points must be considered:
1. Skin contact must be avoided by wearing protective gloves. Gurit recommends the use of disposable nitrile gloves for most applications.
The use of barrier creams is not recommended, but to preserve skin condition a moisturising cream should be used after washing.
2. Overalls or other protective clothing should be worn when mixing, laminating or sanding. Contaminated work clothes should be thoroughly
cleaned before re-use.
3. Eye protection should be worn if there is a risk of resin, hardener, solvent or dust entering the eyes. If this occurs flush the eye with water
for 15 minutes, holding the eyelid open, and seek medical attention.
4. Ensure adequate ventilation in work areas. Respiratory protection should be worn if there is insufficient ventilation. Solvent vapours should
not be inhaled as they can cause dizziness, headaches, loss of consciousness and can have long term health effects.
5. If the skin becomes contaminated, then the area must be immediately cleansed. The use of resin-removing cleansers is recommended. To
finish, wash with soap and warm water. The use of solvents on the skin to remove resins etc must be avoided.
Washing should be part of routine practice:
before eating or drinking
before smoking
before using the lavatory
after finishing work
6. The inhalation of sanding dust should be avoided and if it settles on the skin then it should be washed off. After more extensive sanding
operations a shower/bath and hair wash is advised.
APPLICABLE RISK & SAFETY PHRASES
Gurit produces a separate full Safety Data Sheet for all hazardous products. Please ensure that you have the correct SDS to hand for the
materials you are using before commencing work.

PDS-Spabond340LV(HT)-12-0219 3

SPABOND 340LV & HT FAST HARDENER
This 1 page product summary is intended for use in conjunction with further advice provided under the Instructions for Use section. All data has
been generated from typical production material and does not constitute a product specification.
MIXING AND HANDLING

PROPERTY UNITS Spabond 340LV RESIN FAST HARDENER MIXED SYSTEM TEST METHOD
Appearance – colour Description Yellow Red Pink –
Appearance – form Description Thixotropic Paste –
Mix ratio by weight Parts by weight 100 49 –
Mix ratio by volume Parts by volume 100 50 – –
Density at 21 C g/cm
3
1.13 1.10 1.11 Archimedes

COMPONENT & MIXED SYSTEM VISCOSITY

PROPERTY UNITS 15 C 20 C 25 C 30 C TEST METHOD
Spabond 340LV Resin Viscosity P 490 290 257 130 –
Spabond 340LV HT Fast Hardener Viscosity P 713 472 322 259 –
Initial Mixed System Viscosity P 733 427 275 196 –
Pot-life (500 g, mixed in air)* hrs:min 00:20 00:16 00:12 00:10 –
Clamp Time*
(time to 2kN cleavage strength)
hrs:min 05:12 03:50 02:50 02:05 BS 5350 Part C1
Sag resistance* mm – 20 20 – –

ADHESIVE PERFORMANCE

MECHANICAL PROPERTIES SYMBOL UNITS 28 DAYS AT 21 C 16 HOURS AT 50 C** 5 HOURS AT 70 C** TEST STANDARD
Cleavage on steel Fcleavage kN 9.2 11.3 7.8 BS 5350 Part C1
Lap shear on steel steel MPa 29 31 30 BS 5350 Part C5

CURED MECHANICAL AND THERMAL PROPERTIES

MECHANICAL PROPERTIES SYMBOL UNITS 28 DAYS AT 21 C 16 HOURS AT 50 C** 5 HOURS AT 70 C** TEST STANDARD
Glass Transition Temperature Tg1 C 54 67 71 ISO 6721 (DMA)
Cured Density ply g/cm
3
1.17 1.17 1.17 Archimedes
Volumetric Shrinkage % 5.77 5.41 5.32 Archimedes
Tensile Strength T MPa 37 50 48 ISO 527-2
Tensile Modulus ET GPa 2.85 2.77 2.75 ISO 527-2
Tensile Strain T % 7.73 9.07 10.1 ISO 527-2
3-point flexural strength F N/mm
2
72 85 83 ISO 178
3-point flexural modulus EF GPa 2.75 2.53 2.46 ISO 178
Charpy (notched) kJ/m
2
1.49 2.26 1.91 ISO 179-1

*working time properties are highly subjective to ambient conditions and should be used an approximate guideline for all Spabond 340 systems
**initial cure of 24 hours at 21 C

PDS-Spabond340LV(HT)-12-0219 4

SPABOND 340LV & HT SLOW HARDENER
This 1 page product summary is intended for use in conjunction with further advice provided under the Instructions for Use section. All data
has been generated from typical production material and does not constitute a product specification.
MIXING AND HANDLING

PROPERTY UNITS Spabond 340LV RESIN SLOW HARDENER MIXED SYSTEM TEST METHOD
Appearance – colour Description Yellow Purple Grey –
Appearance – form Description Thixotropic Paste
–
Mix ratio by weight Parts by weight 100 49 –
Mix ratio by volume Parts by volume 100 50 – –
Density at 21 C g/cm
3
1.13 1.11 1.12 Archimedes

COMPONENT & MIXED SYSTEM VISCOSITY

PROPERTY UNITS 15 C 20 C 25 C 30 C TEST METHOD
Spabond 340LV Resin Viscosity P 490 290 257 130 –
Spabond 340LV HT Slow Hardener Viscosity P 559 391 282 232 –
Initial Mixed System Viscosity P 673 403 264 190 –
Pot-life (500 g, mixed in air)* hrs:min 01:00 00:45 00:34 00:26 –
Clamp Time*
(time to 2kN cleavage strength)
hrs:min 23:00 17:40 13:30 10:20 BS 5350 Part C1
Sag resistance* mm – 20 20 – –

ADHESIVE PERFORMANCE

MECHANICAL PROPERTIES SYMBOL UNITS 28 DAYS AT 21 C 16 HOURS AT 50 C** 5 HOURS AT 70 C** TEST STANDARD
Cleavage on steel Fcleavage kN 8.9 12.0 10.1 BS 5350 Part C1
Lap shear on steel steel MPa 32 37 36 BS 5350 Part C5

CURED MECHANICAL AND THERMAL PROPERTIES

MECHANICAL PROPERTIES SYMBOL UNITS 28 DAYS AT 21 C 16 HOURS AT 50 C** 5 HOURS AT 70 C** TEST STANDARD
Glass Transition Temperature Tg1 C 52 66 72 ISO 6721 (DMA)
Cured Density ply g/cm
3
1.18 1.17 1.17 Archimedes
Volumetric Shrinkage % 5.18 4.64 4.29 Archimedes
Tensile Strength T MPa 34 49 49 ISO 527-2
Tensile Modulus ET GPa 2.93 2.58 2.89 ISO 527-2
Tensile Strain T % 6.31 7.83 8.28 ISO 527-2
3-point flexural strength F N/mm
2
68 85 87 ISO 178
3-point flexural modulus EF GPa 3.04 2.62 2.67 ISO 178
Charpy (notched) kJ/m
2
1.42 2.53 2.56 ISO 179-1

*working time properties are highly subjective to ambient conditions and should be used an approximate guideline for all Spabond 340 systems
**initial cure of 24 hours at 21 C

PDS-Spabond340LV(HT)-12-0219 5

SPABOND 340LV & HT EXTRA-SLOW HARDENER
This 1 page product summary is intended for use in conjunction with further advice provided under the Instructions for Use section. All data
has been generated from typical production material and does not constitute a product specification.
MIXING AND HANDLING

PROPERTY UNITS Spabond 340LV RESIN X-SLOW HARDENER MIXED SYSTEM TEST METHOD
Appearance – colour Description Yellow Blue Green –
Appearance – form Description Thixotropic Paste –
Mix ratio by weight Parts by weight 100 47 –
Mix ratio by volume Parts by volume 100 50 – –
Density at 21 C g/cm
3
1.13 1.05 1.11 Archimedes

COMPONENT & MIXED SYSTEM VISCOSITY

PROPERTY UNITS 15 C 20 C 25 C 30 C TEST METHOD
Spabond 340LV Resin Viscosity P 490 290 257 130 –
Spabond 340LV HT Extra-Slow Hardener Viscosity P 578 330 215 150 –
Initial Mixed System Viscosity P 683 381 242 167 –
Pot-life (500 g, mixed in air)* hrs:min 03:10 02:20 01:40 01:15 –
Clamp Time*
(time to 2kN cleavage strength)
hrs:min 33:50 24:00 14:50 10:30 BS 5350 Part C1
Sag resistance* mm – 20 20 – –

ADHESIVE PERFORMANCE

MECHANICAL PROPERTIES SYMBOL UNITS 28 DAYS AT 21 C 16 HOURS AT 50 C** 5 HOURS AT 70 C** TEST STANDARD
Cleavage on steel Fcleavage kN 7.9 11.2 11.9 BS 5350 Part C1
Lap shear on steel steel MPa 29 34 35 BS 5350 Part C5

CURED MECHANICAL AND THERMAL PROPERTIES

MECHANICAL PROPERTIES SYMBOL UNITS 28 DAYS AT 21 C 16 HOURS AT 50 C** 5 HOURS AT 70 C** TEST STANDARD
Glass Transition Temperature Tg1 C 51 66 72 ISO 6721 (DMA)
Cured Density ply g/cm
3
1.15 1.14 1.15 Archimedes
Volumetric Shrinkage % 3.42 3.06 3.15 Archimedes
Tensile Strength T MPa 31 47 44 ISO 527-2
Tensile Modulus ET GPa 2.90 2.63 2.89 ISO 527-2
Tensile Strain T % 3.46 4.77 6.15 ISO 527-2
3-point flexural strength F N/mm
2
63 84 83 ISO 178
3-point flexural modulus EF GPa 2.89 2.68 2.70 ISO 178
Charpy (notched) kJ/m
2
1.24 2.12 1.93 ISO 179-1

*working time properties are highly subjective to ambient conditions and should be used an approximate guideline for all Spabond 340 systems
**initial cure of 24 hours at 21 C

PDS-Spabond340LV(HT)-12-0219 6

NOTICE
All advice, instruction or recommendation is given in good faith but the selling Gurit entity (the
Company) only warrants that advice in writing is given with reasonable skill and care. No further duty
or responsibility is accepted by the Company. All advice is given subject to the terms and conditions
of sale (the Conditions) which are available on request from the Company or may be viewed at
Gurit s Website: www.gurit.com/terms-and-conditions.aspx
The Company strongly recommends that Customers make test panels in the final process conditions
and conduct appropriate testing of any goods or materials supplied by the Company prior to final
use to ensure that they are suitable for the Customer s planned application. Such testing should
include testing under conditions as close as possible to those to which the final component may be
subjected. The Company specifically excludes any warranty of fitness for purpose of the goods other
than as set out in writing by the Company. Due to the varied nature of end-use applications, the
Company does, in particular, not warrant that the test panels in the final process conditions and/or
the final component pass any fire standards.
The Company reserves the right to change specifications and prices without notice and Customers
should satisfy themselves that information relied on by the Customer is that which is currently
published by the Company on its website. Any queries may be addressed to the Technical Services
Department.
Gurit is continuously reviewing and updating literature. Please ensure that you have the current
version by contacting your sales contact and quoting the revision number in the bottom left-hand
corner of this page.
TECHNICAL CONTACT INFORMATION
For all other enquiries such as technical queries:
Telephone + 44 1983 828000 (08:30 17:00 GMT)
Email technical.support@gurit.com
24-HOUR CHEMICAL EMERGENCY NUMBER
For advice on chemical emergencies, spillages, fires or exposures:
Europe +44 1273 289451
Americas +1 646 844 7309
APAC +65 3158 1412

All trademarks used or mentioned in this document are protected by law.

E customer.support@gurit.com
W www.gurit.com

1
product DATA SHEET
SikaBiresin CR77 FR
February 19, Version 01 /2021

1
PRODUCT DATA SHEET
SikaBiresin CR77 FR with CH77-2 Fast and CH77-4 Slow Hardeners

(FORMERLY EL-319)
EPOXY LAMINATING SYSTEM
FLAME RETARDANT, MEETS FAR 25.853 FLAME TESTING

DESCRIPTION
SikaBiresin

CR77 FR is a UV stabilized **Halogen-Free Flame Retardant Epoxy
Laminating System developed for use in fabricating parts or repairs on structures
which require flame retardant, self-extinguishing properties with room-
temperature curing capabilities (or post cure options).

SikaBiresin

CR77 FR resin is available with two hardener choices: SikaBiresin

CH77-2 Fast, a moderate work-life hardener for fast turnaround laminating of
production parts and repairs, or SikaBiresin

CH77-4 Slow, a long work-life
hardener for laminating and vacuum bagging of large parts and repairs.

**SikaBiresin

CR77 FR Resin does not contain PBDE or OBDE or DBDE
Flame retardant additive

Suitable for vacuum bagging or RTM
Applications areas include – Aerospace, transportation, architectural and
others

PROPERTIES
Low viscosity for good wet-out
Non-Halogen flame retardancy
Self-extinguishing
Two hardener choices (fast/slow)

RoHS and REACH compliant
Epoxy (non-styrene)
Excellent bond to all fabrics

TYPICAL PHYSICAL PROPERTIES

Units
SikaBiresin

CR77 FR (A)
Resin
SikaBiresin

CH77-2 (B)
Fast Hardener
SikaBiresin

CH77-4 (B)
Slow Hardener
Composition Epoxy Amine Amine
Mix ratio by weight 100 12 19
Aspect Clear Liquid Clear Liquid Clear Liquid
Color Visual Light Amber Light Amber Light Amber
Viscosity Brookfield Cps. 9,720 40 30
Viscosity Brookfield (mixed) Cps.

1,865 1,105

product DATA SHEET
SikaBiresin CR77 FR
February 19, Version 01 /2021

2
Density at 77 F (25 C) (mixed) lbs./gal (g/cc) 9.78 (1.17)

8.10 (.97) 7.94 (.95)
Pot life (200g) at 77 F (25 C) minutes 50 139

MECHANICAL PROPERTIES

MECHANICAL AND THERMAL PROPERTIES (NEAT FORM)
Property Test Method Units(s)
SikaBiresin

CH77-2 (B)
Fast Hardener*
SikaBiresin

CH77-2 (B)
Fast Hardener**
SikaBiresin

CH77-4 (B)
Slow Hardener**
SikaBiresin

CH77-4 (B)
Slow Hardener**
Hardness ASTM D2240 Shore D 87 88 87 87
Flexural strength ASTM D790 psi (MPa) 13,040 (90) 14,593 (101) 11,535 (80) 17,006 (117)
Flexural modulus ASTM D790 psi (MPa) 473,215 (3,265) 560,077 (3,864) 372,726 (2,572) 527,632 (3,641)
Tensile strength ASTM D638 psi (MPa) 7,510 (52) 9,799 (68) 7,067 (49) 10,424 (72)
Tensile modulus ASTM D638 psi (MPa) 341,734 (2,358) 349,476 (2,411) 250,994 (1,732) 309,786 (2,136)
Elongation ASTM D638 % 2.6 3.3 4.0 4.4
Tg (TMA) ASTM E1545 F ( C) 113 (45) 170 (77) 98 (38) 115 (45)
*Cure schedule: *7 day at 77 F (25 C) **24-36 hr at 77 F (25 C) + 4 hr 212 F (100 C)

Flame Retardant Properties**
Test Description Test Method Test Results
(F1) 60 second Vertical Burn Test FAR/JAR 25.853 Pass
(F2) 12 second- Vertical Burn Test Req. FAR/JAR 25.853 Pass
(F5) 30 second-45 Angle Burn Test FAR/JAR 25.853 Pass

** FAR/JAR 25.853 Appendix F, Part (a)(1)(i), (ii), (v) (4 ply 7500 Style E-Glass Laminate),
Cure schedule: 7 days/77 F (25 C). Testing done at third party laboratory.

PROCESSING

Normal health and safety precautions should be observed when handling these
products:
Ensure good ventilation.
Wear gloves, glasses and protective clothes.
For further information, please consult the Safety Data Sheets.

product DATA SHEET
SikaBiresin CR77 FR
February 19, Version 01 /2021

3

STORAGE CONDITIONS

Product shelf life of resin and hardener(s) is 24 months when stored in original
unopened containers between 65 77 F (15 25 C). Any opened can must be
tightly closed.

PACKAGING

Packaging information on request, please contact your local sales representative. or
find your local contact on www.sikaindustry.com

LEGAL NOTICE
The information, and, in particular, the recommendations relating to the application
and end-use of Sika products, are given in good faith based on Sika s current
knowledge and experience of the products when properly stored, handled and applied
under normal conditions in accordance with Sika s recommendations. In practice, the
differences in materials, substrates and actual site conditions are such that no
warranty in respect of merchantability or of fitness for a particular purpose, nor any
liability arising out of any legal relationship whatsoever, can be inferred either from
this information, or from any written recommendations, or from any other advice
offered. The user of the product must test the product s suitability for the intended
application and purpose. Sika reserves the right to change the properties of its
products. The proprietary rights of third parties must be observed. All orders are
accepted subject to our current terms of sale and delivery. Users must always refer to
the most recent issue of the local Product Data Sheet for the product concerned,
copies of which will be supplied on request.

CONTACT

UNITED STATES
Sika Corporation
30800 Stephenson Highway
Madison Heights, Michigan 48071 USA
Tel.: (+1) 248 588-2270
Fax: (+1) 248 577-0810
Website: www.sikaindustry.com

1

80LS- 32 SYSTEM
EPOXY LAMINATING RESIN

80LS-32 is a100% solids epoxy laminating system. The system yields an increased cross link
density making it especially suitable for lightweight, high performance composites using a
variety of reinforcements.

USES
To make lightweight composites Hand lay up application
Coating Repair applications.

PERFORMANCE BENEFITS

Superior fatigue and toughness
properties
Good adhesion to fabrics, core
materials
Good moisture exclusion Excellent wet out and air release
Good clarity

CURING 80LS-32 SYSTEM

80LS-32 system mixes maintain good working properties until gelation takes place.
Allow the composite to cure for 3 hours at 130 F for best results.

TYPICAL LIQUID SYSTEM PROPERTIES AT 25 C/77 F FOR AO 80LS-32 SYSTEM

Property 80LS-32
Mix Ratio (parts by weight)

100 Resin/ Hardener 22

Density part A, lbs/gal 9.5
Density part B, lbs/gal 8.2
Density (mixed), lbs/gal 9.17
Viscosity (mixed) 900-1200 cps
Specific Gravity, (mixed) 1.098
Color, mixed Amber
Pot Life @ 77 F 33-38 minutes
Cure Time, Hrs at 130 F 3 Hrs

Our Products are intended for sale to industrial and commercial customers. We request that Customers inspect and test our products before use
and satisfy themselves as to contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any warranty or
merchantability or fitness, nor is protection from any law of patent to be inferred. All patent rights are reserved. The exclusive remedy for all
proven claims is replacement of our materials and in no event shall we be liable for special , incidental or consequential damages
Last updated June 12, 2018 ISO 9001:2015 Registered Company

2

CURED SYSTEM PROPERTIES FOR 80LS-32 SYSTEM

Property 80LS-32
Hardness, Shore D, ASTM D-2240: 1 Day Cure

79

Glass Transition Temp >170 F

PACKAGING WEIGHTS IN LBS

Material Gallon Pail Drum
80LS-32A Resin (lbs) 7.3 36.4 364
80LS-32B
Hardener (lbs)
1.6 8.0 80 (2Pails)

1

80LS- 32 SYSTEM
EPOXY LAMINATING RESIN

80LS-32 is a100% solids epoxy laminating system. The system yields an increased cross link
density making it especially suitable for lightweight, high performance composites using a
variety of reinforcements.

USES
To make lightweight composites Hand lay up application
Coating Repair applications.

PERFORMANCE BENEFITS

Superior fatigue and toughness
properties
Good adhesion to fabrics, core
materials
Good moisture exclusion Excellent wet out and air release
Good clarity

CURING 80LS-32 SYSTEM

80LS-32 system mixes maintain good working properties until gelation takes place.
Allow the composite to cure for 3 hours at 130 F for best results.

TYPICAL LIQUID SYSTEM PROPERTIES AT 25 C/77 F FOR AO 80LS-32 SYSTEM

Property 80LS-32
Mix Ratio (parts by weight)

100 Resin/ Hardener 22

Density part A, lbs/gal 9.5
Density part B, lbs/gal 8.2
Density (mixed), lbs/gal 9.17
Viscosity (mixed) 900-1200 cps
Specific Gravity, (mixed) 1.098
Color, mixed Amber
Pot Life @ 77 F 33-38 minutes
Cure Time, Hrs at 130 F 3 Hrs

Our Products are intended for sale to industrial and commercial customers. We request that Customers inspect and test our products before use
and satisfy themselves as to contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any warranty or
merchantability or fitness, nor is protection from any law of patent to be inferred. All patent rights are reserved. The exclusive remedy for all
proven claims is replacement of our materials and in no event shall we be liable for special , incidental or consequential damages
Last updated June 12, 2018 ISO 9001:2015 Registered Company

2

CURED SYSTEM PROPERTIES FOR 80LS-32 SYSTEM

Property 80LS-32
Hardness, Shore D, ASTM D-2240: 1 Day Cure

79

Glass Transition Temp >170 F

PACKAGING WEIGHTS IN LBS

Material Gallon Pail Drum
80LS-32A Resin (lbs) 7.3 36.4 364
80LS-32B
Hardener (lbs)
1.6 8.0 80 (2Pails)

05/25/2023 EN (English US) SDS ID: 80LS-27B Page 1

SECTION 1: Identification

1.1. Identification
Product form : Mixture
Trade name : Epoxy General Purpose Laminating Hardener
CAS-No. : Mixture
Product code : 80LS-27B

1.2. Recommended use and restrictions on use
Use of the substance/mixture : HARDENER

1.3. Supplier
Dura Technologies, Inc.
2720 South Willow Avenue #A
Bloomington, CA 92316

909-546-1162
ChemTrec US: 800.424.9300
ChemTrec Int: +1 70 3527 3887

1.4. Emergency telephone number
Emergency number : ChemTrec US: 800.424.9300 Int: +1 70 3527 3887

SECTION 2: Hazard(s) identification

2.1. Classification of the substance or mixture
GHS US classification
Acute toxicity (oral) Category 4 H302 Harmful if swallowed
Acute toxicity (dermal) Category 4 H312 Harmful in contact with skin
Skin corrosion/irritation Category 1B H314 Causes severe skin burns and eye damage
Serious eye damage/eye irritation Category 1 H318 Causes serious eye damage
Skin sensitization, category 1A H317 May cause an allergic skin reaction
Specific target organ toxicity (repeated exposure) Category 2 H373 May cause damage to organs through prolonged or repeated exposure
Hazardous to the aquatic environment – Acute Hazard Category 3 H402 Harmful to aquatic life
Hazardous to the aquatic environment – Chronic Hazard Category 2 H411 Toxic to aquatic life with long lasting effects

Full text of H statements : see section 16

2.2. GHS Label elements, including precautionary statements
GHS US labeling
Hazard pictograms (GHS US) :

Signal word (GHS US) : Danger
Hazard statements (GHS US) : H302+H312 – Harmful if swallowed or in contact with skin
H314 – Causes severe skin burns and eye damage
H317 – May cause an allergic skin reaction
H318 – Causes serious eye damage
H373 – May cause damage to organs through prolonged or repeated exposure
H402 – Harmful to aquatic life
H411 – Toxic to aquatic life with long lasting effects
Precautionary statements (GHS US) : P260 – Do not breathe dust/fume/gas/mist/vapors/spray.
P261 – Avoid breathing dust/fume/gas/mist/vapors/spray.
P264 – Wash hands, forearms and face thoroughly after handling.
P270 – Do not eat, drink or smoke when using this product.
P272 – Contaminated work clothing must not be allowed out of the workplace.
P273 – Avoid release to the environment.
P280 – Wear protective clothing.
P301+P312 – If swallowed: Call a poison center or doctor if you feel unwell.
P301+P330+P331 – If swallowed: rinse mouth. Do NOT induce vomiting.
P302+P352 – If on skin: Wash with plenty of water.

Epoxy General Purpose Laminating Hardener
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

05/25/2023 EN (English US) SDS ID: 80LS-27B 2/10

P303+P361+P353 – If on skin (or hair): Take off immediately all contaminated clothing. Rinse
skin with water/shower.
P304+P340 – If inhaled: Remove person to fresh air and keep comfortable for breathing.
P305+P351+P338 – IF IN EYES: Rinse cautiously with water for several minutes. Remove
contact lenses, if present and easy to do. Continue rinsing.
P310 – Immediately call a poison center or doctor.
P312 – Call a poison center or doctor if you feel unwell.
P314 – Get medical advice/attention if you feel unwell.
P321 – Specific treatment (see supplemental first aid instruction on this label).
P322 – Specific treatment (see supplemental first aid instruction on this label)
P330 – Rinse mouth.
P333+P313 – If skin irritation or rash occurs: Get medical advice/attention.
P362+P364 – Take off contaminated clothing and wash it before reuse.
P363 – Wash contaminated clothing before reuse.
P391 – Collect spillage.
P405 – Store locked up.
P501 – Dispose of contents/container to hazardous or special waste collection point, in
accordance with local, regional, national and/or international regulation.

2.3. Other hazards which do not result in classification
No additional information available
2.4. Unknown acute toxicity (GHS US)
Not applicable
SECTION 3: Composition/Information on ingredients

3.1. Substances
Not applicable
3.2. Mixtures

Name Product identifier % GHS US classification
Epoxy Adduct

(CAS-No.) TRADE SECRET <= 71 Skin Irrit. 2, H315 diethylmethylbenzenediamine (CAS-No.) 68479-98-1 <= 27 Acute Tox. 4 (Oral), H302 Acute Tox. 4 (Dermal), H312 Eye Irrit. 2, H319 STOT RE 2, H373 Aquatic Acute 1, H400 Aquatic Chronic 1, H410 triethylenetetramine (CAS-No.) 112-24-3 <= 3.8 Acute Tox. 3 (Dermal), H311 Skin Corr. 1B, H314 Skin Sens. 1, H317 Aquatic Acute 3, H402 Aquatic Chronic 3, H412 2-piperazin-1-ylethylamine (CAS-No.) 140-31-8 <= 1.5 Acute Tox. 3 (Dermal), H311 Skin Corr. 1, H314 Skin Sens. 1, H317 Aquatic Acute 3, H402 Aquatic Chronic 3, H412 Full text of hazard classes and H-statements : see section 16 SECTION 4: First-aid measures 4.1. Description of first aid measures First-aid measures general : Never give anything by mouth to an unconscious person. If you feel unwell, seek medical advice (show the label where possible). First-aid measures after inhalation : Remove person to fresh air and keep comfortable for breathing. Remove victim to fresh air and keep at rest in a position comfortable for breathing. Immediately call a poison center or doctor/physician. First-aid measures after skin contact : Immediately call a poison center or doctor/physician. Specific measures (see supplemental first aid instruction on this label). Wash with plenty of soap and water. Wash contaminated clothing before reuse. Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower. If skin irritation or rash occurs: Get medical advice/attention. Specific treatment (see supplemental first aid instruction on this label). First-aid measures after eye contact : Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a poison center or doctor/physician. First-aid measures after ingestion : Rinse mouth. Do NOT induce vomiting. Call a POISON CENTER or doctor/physician if you feel unwell. Immediately call a poison center or doctor/physician. Call a poison center/doctor/physician if you feel unwell. Epoxy General Purpose Laminating Hardener Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 05/25/2023 EN (English US) SDS ID: 80LS-27B 3/10 4.2. Most important symptoms and effects (acute and delayed) Potential Adverse human health effects and symptoms : Harmful if swallowed. Harmful in contact with skin. Symptoms/effects : Causes severe skin burns and eye damage. Symptoms/effects after inhalation : Harmful if inhaled. May cause an allergic skin reaction. Symptoms/effects after skin contact : Caustic burns/corrosion of the skin. Repeated exposure to this material can result in absorption through skin causing significant health hazard. Harmful in contact with skin. Symptoms/effects after eye contact : Causes eye irritation. Causes serious eye damage. May cause severe irritation. Symptoms/effects after ingestion : Swallowing a small quantity of this material will result in serious health hazard. 4.3. Immediate medical attention and special treatment, if necessary Until victim can be cared for by specialized staff: SECTION 5: Fire-fighting measures 5.1. Suitable (and unsuitable) extinguishing media Suitable extinguishing media : Sand. Water spray. Dry powder. Foam. Carbon dioxide. Unsuitable extinguishing media : Do not use a heavy water stream. 5.2. Specific hazards arising from the chemical Fire hazard : Heating increases the fire hazard. Heating may cause a fire. Heating may cause a fire or explosion. Insufficient data available on direct fire hazard (flashpoint > 100 C). Self-heating in
large quantities; may catch fire. Temperature above flashpoint: higher fire/explosion hazard.

5.3. Special protective equipment and precautions for fire-fighters
Firefighting instructions : Use water spray or fog for cooling exposed containers. Exercise caution when fighting any
chemical fire. Prevent fire-fighting water from entering environment.
Protection during firefighting : Do not enter fire area without proper protective equipment, including respiratory protection. Do
not attempt to take action without suitable protective equipment. Self-contained breathing
apparatus. Complete protective clothing.
SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures
6.1.1. For non-emergency personnel
Emergency procedures : Ventilate spillage area. Evacuate unnecessary personnel.
6.1.2. For emergency responders
Protective equipment : Do not attempt to take action without suitable protective equipment. Equip cleanup crew with
proper protection. For further information refer to section 8: “Exposure controls/personal
protection”.
Emergency procedures : Ventilate area.

6.2. Environmental precautions
Avoid release to the environment. Prevent entry to sewers and public waters. Notify authorities if liquid enters sewers or public waters.

6.3. Methods and material for containment and cleaning up
Methods for cleaning up : Take up liquid spill into absorbent material. Soak up spills with inert solids, such as clay or
diatomaceous earth as soon as possible. Collect spillage. Store away from other materials.
Other information : Dispose of materials or solid residues at an authorized site.

6.4. Reference to other sections
See Heading 8. Exposure controls and personal protection. For further information refer to section 13.
SECTION 7: Handling and storage

7.1. Precautions for safe handling
Precautions for safe handling : Ensure good ventilation of the work station. Wear personal protective equipment. Wash hands
and other exposed areas with mild soap and water before eating, drinking or smoking and
when leaving work. Provide good ventilation in process area to prevent formation of vapor. Do
not breathe dust/fume/gas/mist/vapors/spray. Avoid breathing dust/fume/gas/mist/vapors/spray.
Hygiene measures : Wash hands, forearms and face thoroughly after handling. Wash contaminated clothing before
reuse. Contaminated work clothing should not be allowed out of the workplace. Do not eat,
drink or smoke when using this product. Always wash hands after handling the product.

7.2. Conditions for safe storage, including any incompatibilities
Technical measures : Comply with applicable regulations.

Epoxy General Purpose Laminating Hardener
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

05/25/2023 EN (English US) SDS ID: 80LS-27B 4/10

Storage conditions : Keep only in the original container in a cool, well ventilated place away from : Keep container
closed when not in use. Store in a well-ventilated place. Keep cool.
Incompatible products : Strong bases. Strong acids.
Incompatible materials : Sources of ignition. Direct sunlight.

SECTION 8: Exposure controls/personal protection

8.1. Control parameters

diethylmethylbenzenediamine (68479-98-1)
Not applicable

triethylenetetramine (112-24-3)
Not applicable

2-piperazin-1-ylethylamine (140-31-8)
Not applicable

Epoxy Adduct (TRADE SECRET)
Not applicable

8.2. Appropriate engineering controls
Appropriate engineering controls : Ensure good ventilation of the work station.
Environmental exposure controls : Avoid release to the environment.

8.3. Individual protection measures/Personal protective equipment
Personal protective equipment:
Avoid all unnecessary exposure.

Hand protection:
Wear protective gloves.

Eye protection:
Chemical goggles or face shield. Safety glasses

Skin and body protection:
Wear suitable protective clothing

Respiratory protection:
Wear appropriate mask

Other information:
Do not eat, drink or smoke during use.

SECTION 9: Physical and chemical properties

9.1. Information on basic physical and chemical properties
Physical state : Liquid

Appearance : amber.
Color : amber

Odor : characteristic

Odor threshold : No data available

pH : No data available

Melting point : Not applicable

Freezing point : No data available

Boiling point : > 392 F

Flash point : >= 212 F

Relative evaporation rate (butyl acetate=1) : No data available

Relative evaporation rate (ether=1) : < 1 slower than ether Flammability (solid, gas) : Non flammable. Epoxy General Purpose Laminating Hardener Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 05/25/2023 EN (English US) SDS ID: 80LS-27B 5/10 Vapor pressure : < 4 mm Hg Relative vapor density at 20 C : No data available Relative density : No data available Density : 0.98 kg/l Solubility : No data available Log Pow : No data available Auto-ignition temperature : No data available Decomposition temperature : No data available Viscosity, kinematic : No data available Viscosity, dynamic : No data available Explosion limits : No data available Explosive properties : No data available Oxidizing properties : No data available 9.2. Other information No additional information available SECTION 10: Stability and reactivity 10.1. Reactivity Thermal decomposition generates : Corrosive vapors. 10.2. Chemical stability Stable under normal conditions. Not established. 10.3. Possibility of hazardous reactions Not established. 10.4. Conditions to avoid Direct sunlight. Extremely high or low temperatures. 10.5. Incompatible materials Strong acids. Strong bases. 10.6. Hazardous decomposition products fume. Carbon monoxide. Carbon dioxide. Thermal decomposition generates : Corrosive vapors. SECTION 11: Toxicological information 11.1. Information on toxicological effects Acute toxicity (oral) : Harmful if swallowed. Acute toxicity (dermal) : Harmful in contact with skin. Acute toxicity (inhalation) : Not classified ATE US (oral) 1778.242 mg/kg body weight ATE US (dermal) 1100 mg/kg body weight diethylmethylbenzenediamine (68479-98-1) ATE US (oral) 500 mg/kg body weight ATE US (dermal) 1100 mg/kg body weight triethylenetetramine (112-24-3) LD50 oral rat 2500 mg/kg (Rat, Literature, Oral) LD50 dermal rabbit 805 mg/kg (Rabbit, Literature, Dermal) ATE US (oral) 2500 mg/kg body weight ATE US (dermal) 805 mg/kg body weight 2-piperazin-1-ylethylamine (140-31-8) LD50 oral rat 2097 mg/kg body weight (Rat, Male, Experimental value, Oral, 14 day(s)) LD50 dermal rabbit 866 mg/kg bw/day (24 h, Rabbit, Male, Experimental value, Dermal, 14 day(s)) ATE US (oral) 2097 mg/kg body weight ATE US (dermal) 866 mg/kg body weight Skin corrosion/irritation : Causes severe skin burns and eye damage. Serious eye damage/irritation : Causes serious eye damage. Epoxy General Purpose Laminating Hardener Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 05/25/2023 EN (English US) SDS ID: 80LS-27B 6/10 Respiratory or skin sensitization : May cause an allergic skin reaction. Germ cell mutagenicity : Not classified Carcinogenicity : Not classified Reproductive toxicity : Not classified STOT-single exposure : Not classified STOT-repeated exposure : May cause damage to organs through prolonged or repeated exposure. diethylmethylbenzenediamine (68479-98-1) STOT-repeated exposure May cause damage to organs through prolonged or repeated exposure. Aspiration hazard : Not classified Viscosity, kinematic : No data available Likely routes of exposure : Inhalation. Potential Adverse human health effects and symptoms : Harmful if swallowed. Harmful in contact with skin. Symptoms/effects : Causes severe skin burns and eye damage. Symptoms/effects after inhalation : Harmful if inhaled. May cause an allergic skin reaction. Symptoms/effects after skin contact : Caustic burns/corrosion of the skin. Repeated exposure to this material can result in absorption through skin causing significant health hazard. Harmful in contact with skin. Symptoms/effects after eye contact : Causes eye irritation. Causes serious eye damage. May cause severe irritation. Symptoms/effects after ingestion : Swallowing a small quantity of this material will result in serious health hazard. SECTION 12: Ecological information 12.1. Toxicity Ecology - general : Dangerous for the environment. Harmful to aquatic life. Ecology - water : Harmful to aquatic life. Toxic to aquatic life with long lasting effects. Harmful to aquatic life with long lasting effects. triethylenetetramine (112-24-3) LC50 fish 1 495 mg/l (96 h, Pimephales promelas, Fresh water, Literature study) EC50 Daphnia 1 31.1 mg/l (Equivalent or similar to OECD 202, 48 h, Daphnia magna, Literature study) ErC50 (algae) >= 100 mg/l (DIN 38412-9, 72 h, Scenedesmus subspicatus, Literature study, Growth)

2-piperazin-1-ylethylamine (140-31-8)
LC50 fish 1 2190 mg/l (96 h, Pimephales promelas, Static system, Fresh water, Experimental value)
EC50 Daphnia 1 58 mg/l (OECD 202: Daphnia sp. Acute Immobilisation Test, 48 h, Daphnia magna, Static
system, Experimental value, GLP)
ErC50 (algae) > 1000 mg/l (OECD 201: Alga, Growth Inhibition Test, 72 h, Pseudokirchneriella subcapitata,
Fresh water, Experimental value, GLP)

12.2. Persistence and degradability
Epoxy General Purpose Laminating Hardener (Mixture)
Persistence and degradability May cause long-term adverse effects in the environment.

triethylenetetramine (112-24-3)
Persistence and degradability Not readily biodegradable in water. No (test)data on mobility of the substance available.
Photodegradation in the air. Not established.

2-piperazin-1-ylethylamine (140-31-8)
Persistence and degradability Not readily biodegradable in water.
Chemical oxygen demand (COD)
0.56 g O /g substance

12.3. Bioaccumulative potential
Epoxy General Purpose Laminating Hardener (Mixture)
Bioaccumulative potential Not established.

triethylenetetramine (112-24-3)
BCF other aquatic organisms 1 3.162 (BCFBAF v3.01, Calculated value)

Epoxy General Purpose Laminating Hardener
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

05/25/2023 EN (English US) SDS ID: 80LS-27B 7/10

triethylenetetramine (112-24-3)
Log Pow -2.65 (Estimated value, KOWWIN)
Bioaccumulative potential Bioaccumulation: not applicable. Not established.

2-piperazin-1-ylethylamine (140-31-8)
BCF fish 1 0.3 – 6.3 (OECD 305: Bioconcentration: Flow-Through Fish Test, 6 week(s), Cyprinus carpio,
Flow-through system, Fresh water, Read-across)
Log Pow -1.48 (Experimental value, OECD 107: Partition Coefficient (n-octanol/water): Shake Flask
Method, 20 C)
Bioaccumulative potential Not bioaccumulative.

12.4. Mobility in soil

triethylenetetramine (112-24-3)
Log Koc 1.885 (log Koc, SRC PCKOCWIN v2.0, Calculated value)
Ecology – soil Highly mobile in soil.

2-piperazin-1-ylethylamine (140-31-8)
Log Koc 4.57 (log Koc, Read-across, GLP)
Ecology – soil Low potential for mobility in soil.

12.5. Other adverse effects

Other information : Avoid release to the environment.
SECTION 13: Disposal considerations

13.1. Disposal methods
Regional legislation (waste) : Disposal must be done according to official regulations.
Waste treatment methods : Dispose of contents/container in accordance with licensed collector s sorting instructions.
Sewage disposal recommendations : Do not discharge into drains.
Product/Packaging disposal recommendations : Dispose in a safe manner in accordance with local/national regulations. Dispose of
contents/container to hazardous or special waste collection point, in accordance with local,
regional, national and/or international regulation.
Ecology – waste materials : Avoid release to the environment.
SECTION 14: Transport information

Department of Transportation (DOT)
In accordance with DOT

Transport document description : UN2735 Polyamines, liquid, corrosive, n.o.s. (diethylmethylbenzenediamine ;
triethylenetetramine), 8, III
UN-No.(DOT) : UN2735
Proper Shipping Name (DOT) : Polyamines, liquid, corrosive, n.o.s.
Class (DOT) : 8 – Class 8 – Corrosive material 49 CFR 173.136
Packing group (DOT) : III – Minor Danger
Hazard labels (DOT) : 8 – Corrosive

Dangerous for the environment : Yes
Marine pollutant : Yes

Epoxy General Purpose Laminating Hardener
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

05/25/2023 EN (English US) SDS ID: 80LS-27B 8/10

DOT Packaging Non Bulk (49 CFR 173.xxx) : 203
DOT Packaging Bulk (49 CFR 173.xxx) : 241
DOT Special Provisions (49 CFR 172.102) : IB3 – Authorized IBCs: Metal (31A, 31B and 31N); Rigid plastics (31H1 and 31H2); Composite
(31HZ1 and 31HA2, 31HB2, 31HN2, 31HD2 and 31HH2). Additional Requirement: Only liquids
with a vapor pressure less than or equal to 110 kPa at 50 C (1.1 bar at 122 F), or 130 kPa at 55
C (1.3 bar at 131 F) are authorized, except for UN2672 (also see Special Provision IP8 in Table
2 for UN2672).
T7 – 4 178.274(d)(2) Normal…………. 178.275(d)(3)
TP1 – The maximum degree of filling must not exceed the degree of filling determined by the
following: Degree of filling = 97 / 1 + a (tr – tf) Where: tr is the maximum mean bulk temperature
during transport, and tf is the temperature in degrees celsius of the liquid during filling.
TP28 – A portable tank having a minimum test pressure of 2.65 bar (265 kPa) may be used
provided the calculated test pressure is 2.65 bar or less based on the MAWP of the hazardous
material, as defined in 178.275 of this subchapter, where the test pressure is 1.5 times the
MAWP.
DOT Packaging Exceptions (49 CFR 173.xxx) : 154
DOT Quantity Limitations Passenger aircraft/rail
(49 CFR 173.27)
: 5 L
DOT Quantity Limitations Cargo aircraft only (49
CFR 175.75)
: 60 L
DOT Vessel Stowage Location : A – The material may be stowed on deck or under deck on a cargo vessel and on a
passenger vessel.
DOT Vessel Stowage Other : 52 – Stow separated from acids
Emergency Response Guide (ERG) Number : 153
Other information : No supplementary information available.
Transportation of Dangerous Goods

Not applicable

Transport by sea

Transport document description (IMDG) : UN 2735 POLYAMINES, LIQUID, CORROSIVE, N.O .S. (diethylmethylbenzenediamine ;
triethylenetetramine), 8, III
UN-No. (IMDG) : 2735
Proper Shipping Name (IMDG) : POLYAMINES, LIQUID, CORROSIVE, N.O.S .
Class (IMDG) : 8 – Corrosive substances
Packing group (IMDG) : III – substances presenting low danger
Marine pollutant : Yes

Air transport

Transport document description (IATA) : UN 2735 Amines, liquid, corrosive, n.o.s. (diethylmethylbenzenediamine ; triethylenetetramine),
8, III
UN-No. (IATA) : 2735
Proper Shipping Name (IATA) : Amines, liquid, corrosive, n.o.s.
Class (IATA) : 8 – Corrosives
Packing group (IATA) : III – Minor Danger

SECTION 15: Regulatory information

15.1. US Federal regulations
Epoxy General Purpose Laminating Hardener (Mixture)
SARA Section 311/312 Hazard Classes Delayed (chronic) health hazard

triethylenetetramine (112-24-3)
Listed on the United States TSCA (Toxic Substances Control Act) inventory

Epoxy General Purpose Laminating Hardener
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

05/25/2023 EN (English US) SDS ID: 80LS-27B 9/10

2-piperazin-1-ylethylamine (140-31-8)
Listed on the United States TSCA (Toxic Substances Control Act) inventory

15.2. International regulations

CANADA
No additional information available

triethylenetetramine (112-24-3)
Listed on the Canadian DSL (Domestic Substances List)

2-piperazin-1-ylethylamine (140-31-8)
Listed on the Canadian DSL (Domestic Substances List)

EU-Regulations
No additional information available

National regulations
No additional information available

15.3. US State regulations

Component State or local regulations
triethylenetetramine(112-24-3) U.S. – New Jersey – Right to Know Hazardous Substance List
2-piperazin-1-ylethylamine(140-31-8) U.S. – New Jersey – Right to Know Hazardous Substance List

SECTION 16: Other information

according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

Revision date : 05/16/2023
Data sources : REGULATION (EC) No 1272/2008 OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 16 December 2008 on classification, labeling and packaging of substances and
mixtures, amending and repealing Directives 67/548/EEC and 1999/45/EC, and amending
Regulation (EC) No 1907/2006.
Other information : None.

Full text of H-phrases:
H302 Harmful if swallowed
H311 Toxic in contact with skin
H312 Harmful in contact with skin
H314 Causes severe skin burns and eye damage
H315 Causes skin irritation
H317 May cause an allergic skin reaction
H318 Causes serious eye damage
H319 Causes serious eye irritation
H373 May cause damage to organs through prolonged or repeated exposure
H400 Very toxic to aquatic life
H402 Harmful to aquatic life
H410 Very toxic to aquatic life with long lasting effects
H411 Toxic to aquatic life with long lasting effects
H412 Harmful to aquatic life with long lasting effects

Epoxy General Purpose Laminating Hardener
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

05/25/2023 EN (English US) SDS ID: 80LS-27B 10/10

NFPA health hazard : 2 – Materials that, under emergency conditions, can cause
temporary incapacitation or residual injury.

NFPA fire hazard : 1 – Materials that must be preheated before ignition can
occur.
NFPA reactivity : 0 – Material that in themselves are normally stable, even
under fire conditions.

Hazard Rating
Health : 2 Moderate Hazard – Temporary or minor injury may occur
Flammability : 1 Slight Hazard – Materials that must be preheated before ignition will occur. Includes liquids,
solids and semi solids having a flash point above 200 F. (Class IIIB)
Physical : 0 Minimal Hazard – Materials that are normally stable, even under fire conditions, and will NOT
react with water, polymerize, decompose, condense, or self-react. Non-Explosives.

SDS US (GHS HazCom 2012)

To the best of our knowledge this SDS is accurate. The the extent allowed by law, this statement is made in lieu of an other warranties, expressed or implied including but not limited to any implied
warranty of merchantability or fitness for a particular purpose and is in lieu of any other obligations or liability on the part of Dura Technoligies, Inc.

05/25/2023 EN (English US) SDS ID: 80LS-25A Page 1

SECTION 1: Identification

1.1. Identification
Product form : Mixture
Trade name : Epoxy General Purpose Laminating Resin
CAS-No. : Mixture
Product code : 80LS-25A
Formula : mixture

1.2. Recommended use and restrictions on use
Use of the substance/mixture : Epoxy Laminating Resin

1.3. Supplier
Dura Technologies, Inc.
2720 South Willow Avenue #A
Bloomington, CA 92316

909-546-1162
ChemTrec US: 800.424.9300
ChemTrec Int: +1 70 3527 3887

1.4. Emergency telephone number
Emergency number : ChemTrec US: 800.424.9300 Int: +1 70 3527 3887

SECTION 2: Hazard(s) identification

2.1. Classification of the substance or mixture
GHS US classification
Acute toxicity (inhalation) Category 4 H332 Harmful if inhaled
Skin corrosion/irritation Category 2 H315 Causes skin irritation
Serious eye damage/eye irritation Category 2A H319 Causes serious eye irritation
Serious eye damage/eye irritation Category 2B H320 Causes eye irritation
Skin sensitization, Category 1 H317 May cause an allergic skin reaction
Hazardous to the aquatic environment – Acute Hazard Category 3 H402 Harmful to aquatic life

Full text of H statements : see section 16

2.2. GHS Label elements, including precautionary statements
GHS US labeling
Hazard pictograms (GHS US) :

Signal word (GHS US) : Warning
Hazard statements (GHS US) : H315 – Causes skin irritation
H317 – May cause an allergic skin reaction
H319 – Causes serious eye irritation
H320 – Causes eye irritation
H332 – Harmful if inhaled
H402 – Harmful to aquatic life
Precautionary statements (GHS US) : P261 – Avoid breathing dust/fume/gas/mist/vapors/spray.
P264 – Wash hands, forearms and face thoroughly after handling.
P271 – Use only outdoors or in a well-ventilated area.
P272 – Contaminated work clothing must not be allowed out of the workplace.
P273 – Avoid release to the environment.
P280 – Wear protective gloves/protective clothing/eye protection/face protection.
P302+P352 – If on skin: Wash with plenty of water.
P304+P340 – If inhaled: Remove person to fresh air and keep comfortable for breathing.
P305+P351+P338 – IF IN EYES: Rinse cautiously with water for several minutes. Remove
contact lenses, if present and easy to do. Continue rinsing.
P312 – Call a poison center or doctor if you feel unwell.

Epoxy General Purpose Laminating Resin
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

05/25/2023 EN (English US) SDS ID: 80LS-25A 2/8

P321 – Specific treatment (see supplemental first aid instruction on this label).
P332+P313 – If skin irritation occurs: Get medical advice/attention.
P333+P313 – If skin irritation or rash occurs: Get medical advice/attention.
P337+P313 – If eye irritation persists: Get medical advice/attention.
P362+P364 – Take off contaminated clothing and wash it before reuse.
P363 – Wash contaminated clothing before reuse.
P501 – Dispose of contents/container to hazardous or special waste collection point, in
accordance with local, regional, national and/or international regulation.

2.3. Other hazards which do not result in classification
No additional information available
2.4. Unknown acute toxicity (GHS US)
Not applicable
SECTION 3: Composition/Information on ingredients

3.1. Substances
Not applicable
3.2. Mixtures

Name Product identifier % GHS US classification
Propane , 2,2 – bis[p(2,3-epoxypropoxy)phenyl]-, polymers

(CAS-No.) 25085-99-8 <= 88 Skin Irrit. 2, H315 Eye Irrit. 2B, H320 Skin Sens. 1B, H317 1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (CAS-No.) 17557-23-2 <= 11 Skin Irrit. 2, H315 Skin Sens. 1, H317 Aquatic Acute 3, H402 benzyl alcohol (CAS-No.) 100-51-6 <= 8 Acute Tox. 4 (Oral), H302 Acute Tox. 4 (Inhalation), H332 Full text of hazard classes and H-statements : see section 16 SECTION 4: First-aid measures 4.1. Description of first aid measures First-aid measures general : Never give anything by mouth to an unconscious person. If you feel unwell, seek medical advice (show the label where possible). First-aid measures after inhalation : Remove person to fresh air and keep comfortable for breathing. Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or doctor/physician if you feel unwell. Allow affected person to breathe fresh air. Allow the victim to rest. First-aid measures after skin contact : Wash with plenty of soap and water. Wash contaminated clothing before reuse. If skin irritation occurs: Get medical advice/attention. Specific treatment (see supplemental first aid instruction on this label). If skin irritation or rash occurs: Wash skin with plenty of water. First-aid measures after eye contact : Rinse cautiously with water for several minutes. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention. First-aid measures after ingestion : Rinse mouth. Do NOT induce vomiting. Obtain emergency medical attention. Call a poison center/doctor/physician if you feel unwell. 4.2. Most important symptoms and effects (acute and delayed) Potential Adverse human health effects and symptoms : Based on available data, the classification criteria are not met. Symptoms/effects : Causes damage to organs through prolonged or repeated exposure. Symptoms/effects after inhalation : May cause an allergic skin reaction. May cause respiratory irritation. Symptoms/effects after skin contact : Causes skin irritation. Symptoms/effects after eye contact : Causes eye irritation. Causes serious eye irritation. 4.3. Immediate medical attention and special treatment, if necessary Until victim can be cared for by specialized staff: SECTION 5: Fire-fighting measures 5.1. Suitable (and unsuitable) extinguishing media Suitable extinguishing media : Sand. Water spray. Dry powder. Foam. Carbon dioxide. Unsuitable extinguishing media : Do not use a heavy water stream. Epoxy General Purpose Laminating Resin Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 05/25/2023 EN (English US) SDS ID: 80LS-25A 3/8 5.2. Specific hazards arising from the chemical Fire hazard : Heating increases the fire hazard. Heating may cause a fire. Heating may cause a fire or explosion. Insufficient data available on direct fire hazard (flashpoint > 100 C). Self-heating in
large quantities; may catch fire. Temperature above flashpoint: higher fire/explosion hazard.

5.3. Special protective equipment and precautions for fire-fighters
Firefighting instructions : Use water spray or fog for cooling exposed containers. Exercise caution when fighting any
chemical fire. Prevent fire-fighting water from entering environment.
Protection during firefighting : Do not enter fire area without proper protective equipment, including respiratory protection. Do
not attempt to take action without suitable protective equipment. Self-contained breathing
apparatus. Complete protective clothing.
SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures
6.1.1. For non-emergency personnel
Emergency procedures : Ventilate spillage area. Evacuate unnecessary personnel.
6.1.2. For emergency responders
Protective equipment : Do not attempt to take action without suitable protective equipment. Equip cleanup crew with
proper protection. For further information refer to section 8: “Exposure controls/personal
protection”.
Emergency procedures : Ventilate area.

6.2. Environmental precautions
Avoid release to the environment. Prevent entry to sewers and public waters. Notify authorities if liquid enters sewers or public waters.

6.3. Methods and material for containment and cleaning up
For containment : Dam up the liquid spill.
Methods for cleaning up : Take up liquid spill into absorbent material. Soak up spills with inert solids, such as clay or
diatomaceous earth as soon as possible. Collect spillage. Store away from other materials.
Other information : Dispose of materials or solid residues at an authorized site.

6.4. Reference to other sections
See Heading 8. Exposure controls and personal protection. For further information refer to section 13.
SECTION 7: Handling and storage

7.1. Precautions for safe handling
Precautions for safe handling : Wear personal protective equipment. Wash hands and other exposed areas with mild soap and
water before eating, drinking or smoking and when leaving work. Provide good ventilation in
process area to prevent formation of vapor. Avoid breathing dust/fume/gas/mist/vapors/spray.
Use only outdoors or in a well-ventilated area. Do not breathe dust/fume/gas/mist/vapors/spray.
Hygiene measures : Wash hands and other exposed areas with mild soap and water before eat, drink or smoke and
when leaving work. Wash hands, forearms and face thoroughly after handling. Contaminated
work clothing should not be allowed out of the workplace. Wash contaminated clothing before
reuse. Do not eat, drink or smoke when using this product. Always wash hands after handling
the product.

7.2. Conditions for safe storage, including any incompatibilities
Storage conditions : Keep only in the original container in a cool, well ventilated place away from : Keep container
tightly closed. Keep container closed when not in use. Store in a well-ventilated place. Keep
cool.
Incompatible products : Strong bases. Strong acids.
Incompatible materials : Sources of ignition. Direct sunlight.
Storage temperature : 2 – 40 C

SECTION 8: Exposure controls/personal protection

8.1. Control parameters

benzyl alcohol (100-51-6)
Not applicable

1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2)
Not applicable

Epoxy General Purpose Laminating Resin
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

05/25/2023 EN (English US) SDS ID: 80LS-25A 4/8

Propane , 2,2 – bis[p(2,3-epoxypropoxy)phenyl]-, polymers (25085-99-8)
Not applicable

8.2. Appropriate engineering controls
Appropriate engineering controls : Ensure good ventilation of the work station.
Environmental exposure controls : Avoid release to the environment.

8.3. Individual protection measures/Personal protective equipment
Personal protective equipment:
Avoid all unnecessary exposure.

Materials for protective clothing:
GIVE GOOD RESISTANCE: rubber

Hand protection:
Wear protective gloves.

Eye protection:
Chemical goggles or safety glasses. Safety glasses

Skin and body protection:
Wear suitable protective clothing

Respiratory protection:
Wear appropriate mask

Other information:
Do not eat, drink or smoke during use.

SECTION 9: Physical and chemical properties

9.1. Information on basic physical and chemical properties
Physical state : Liquid

Appearance : Liquid.
Color : amber

Odor : slight characteristic

Odor threshold : No data available

pH : No data available

Melting point : N/A

Freezing point : No data available

Boiling point : > 392 F

Flash point : 212 F

Relative evaporation rate (butyl acetate=1) : No data available

Relative evaporation rate (ether=1) : < 1 slower than ether Flammability (solid, gas) : Non flammable. Vapor pressure : <= 3 mm Hg Relative vapor density at 20 C : No data available Relative density : No data available Relative density of saturated gas/air mixture : 1.14 Density : 1.14 kg/l Solubility : Insoluble in water. Log Pow : No data available Auto-ignition temperature : No data available Decomposition temperature : No data available Viscosity, kinematic : No data available Viscosity, dynamic : No data available Epoxy General Purpose Laminating Resin Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 05/25/2023 EN (English US) SDS ID: 80LS-25A 5/8 Explosion limits : No data available Explosive properties : No data available Oxidizing properties : No data available 9.2. Other information No additional information available SECTION 10: Stability and reactivity 10.1. Reactivity The product is non-reactive under normal conditions of use, storage and transport. 10.2. Chemical stability Combustible liquid. Not established. 10.3. Possibility of hazardous reactions Not established. 10.4. Conditions to avoid Open flame. Direct sunlight. Extremely high or low temperatures. 10.5. Incompatible materials Strong acids. Strong bases. 10.6. Hazardous decomposition products fume. Carbon monoxide. Carbon dioxide. SECTION 11: Toxicological information 11.1. Information on toxicological effects Acute toxicity (oral) : Not classified (Lack of data) Acute toxicity (dermal) : Not classified Acute toxicity (inhalation) : Harmful if inhaled. ATE US (gases) 4500 ppmV/4h ATE US (vapors) 11 mg/l/4h ATE US (dust, mist) 1.5 mg/l/4h benzyl alcohol (100-51-6) LD50 oral rat 1620 mg/kg bw/day (Rat, Male, Experimental value, Oral) LD50 dermal rabbit > 2000 mg/kg (Rabbit, Inconclusive, insufficient data, Dermal)
LC50 Inhalation – Rat > 4.178 mg/l air (OECD 403: Acute Inhalation Toxicity, 4 h, Rat, Male / female, Experimental
value, Inhalation (aerosol))
ATE US (oral) 1620 mg/kg body weight
ATE US (gases) 4500 ppmV/4h
ATE US (vapors) 11 mg/l/4h
ATE US (dust, mist) 1.5 mg/l/4h

1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2)
LD50 oral rat 4500 mg/kg (Rat, Literature study, Oral)
LD50 dermal rat > 2100 mg/kg body weight (Rat, Literature study, Dermal)
ATE US (oral) 4500 mg/kg body weight

Skin corrosion/irritation : Causes skin irritation.
Serious eye damage/irritation : Causes serious eye irritation. Causes eye irritation.
Respiratory or skin sensitization : May cause an allergic skin reaction.
Germ cell mutagenicity : Not classified
Carcinogenicity : Not classified

Reproductive toxicity : Not classified
STOT-single exposure : Not classified

STOT-repeated exposure : Not classified

Aspiration hazard : Not classified

Epoxy General Purpose Laminating Resin
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

05/25/2023 EN (English US) SDS ID: 80LS-25A 6/8

Viscosity, kinematic : No data available

Likely routes of exposure : Inhalation.
Potential Adverse human health effects and
symptoms
: Based on available data, the classification criteria are not met.
Symptoms/effects : Causes damage to organs through prolonged or repeated exposure.
Symptoms/effects after inhalation : May cause an allergic skin reaction. May cause respiratory irritation.
Symptoms/effects after skin contact : Causes skin irritation.
Symptoms/effects after eye contact : Causes eye irritation. Causes serious eye irritation.

SECTION 12: Ecological information

12.1. Toxicity
Ecology – general : Dangerous for the environment. Harmful to aquatic life.
Ecology – water : Toxic to aquatic life with long lasting effects.

benzyl alcohol (100-51-6)
LC50 fish 1 460 mg/l (EPA OPP 72-1, 96 h, Pimephales promelas, Static system, Fresh water,
Experimental value, Nominal concentration)
EC50 Daphnia 1 230 mg/l (OECD 202: Daphnia sp. Acute Immobilisation Test, 48 h, Daphnia magna, Fresh
water, Experimental value, GLP)
ErC50 (algae) 770 mg/l (OECD 201: Alga, Growth Inhibition Test, 72 h, Pseudokirchneriella subcapitata,
Static system, Fresh water, Experimental value, GLP)

1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2)
LC50 fish 1 > 100 mg/l (96 h, Pisces, QSAR)
EC50 Daphnia 1 39 – 57 mg/l (OECD 202: Daphnia sp. Acute Immobilisation Test, 48 h, Daphnia magna, Static
system, Fresh water, Experimental value)

12.2. Persistence and degradability
Epoxy General Purpose Laminating Resin (Mixture)
Persistence and degradability May cause long-term adverse effects in the environment.

benzyl alcohol (100-51-6)
Persistence and degradability Biodegradable in the soil. Readily biodegradable in water.
Biochemical oxygen demand (BOD)
1.6 g O /g substance
Chemical oxygen demand (COD)
2.4 g O /g substance
ThOD
2.5 g O /g substance

1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2)
Persistence and degradability Readily biodegradable in water.

12.3. Bioaccumulative potential
Epoxy General Purpose Laminating Resin (Mixture)
Bioaccumulative potential Not established.

benzyl alcohol (100-51-6)
Log Pow 1 – 1.1 (Experimental value, 20 C)
Bioaccumulative potential Low potential for bioaccumulation (Log Kow < 4). 1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2) Log Pow 0.47 (QSAR, KOWWIN, 20 C) Bioaccumulative potential Low potential for bioaccumulation (Log Kow < 4). 12.4. Mobility in soil benzyl alcohol (100-51-6) Surface tension 39 mN/m (20 C) Ecology - soil No (test)data on mobility of the substance available. 1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2) Log Koc 1.22 (log Koc, QSAR) Ecology - soil Highly mobile in soil. Epoxy General Purpose Laminating Resin Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 05/25/2023 EN (English US) SDS ID: 80LS-25A 7/8 12.5. Other adverse effects Other information : Avoid release to the environment. SECTION 13: Disposal considerations 13.1. Disposal methods Regional legislation (waste) : Disposal must be done according to official regulations. Waste treatment methods : Dispose of contents/container in accordance with licensed collector s sorting instructions. Sewage disposal recommendations : Do not discharge into drains. Product/Packaging disposal recommendations : Dispose in a safe manner in accordance with local/national regulations. Dispose of contents/container to hazardous or special waste collection point, in accordance with local, regional, national and/or international regulation. Ecology - waste materials : Avoid release to the environment. SECTION 14: Transport information Department of Transportation (DOT) In accordance with DOT Not regulated Transportation of Dangerous Goods Not regulated Transport by sea Transport document description (IMDG) : UN 3082 ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N. O.S. ( Epoxy Resin ), 9, III, MARINE POLLUTANT UN-No. (IMDG) : 3082 Proper Shipping Name (IMDG) : ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O. S. Class (IMDG) : 9 - Miscellaneous dangerous substances and articles Packing group (IMDG) : III - substances presenting low danger Limited quantities (IMDG) : 5 L Air transport Transport document description (IATA) : UN 3082 Environmentally hazardous substance, liquid, n.o.s. ( Epoxy Resin ), 9, III UN-No. (IATA) : 3082 Proper Shipping Name (IATA) : Environmentally hazardous substance, liquid, n.o.s. Class (IATA) : 9 - Miscellaneous Dangerous Substances and Articles Packing group (IATA) : III - Minor Danger SECTION 15: Regulatory information 15.1. US Federal regulations benzyl alcohol (100-51-6) Listed on the United States TSCA (Toxic Substances Control Act) inventory 1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2) Listed on the United States TSCA (Toxic Substances Control Act) inventory EPA TSCA Regulatory Flag T - T - indicates a substance that is the subject of a final TSCA section 4 test rule. 15.2. International regulations CANADA benzyl alcohol (100-51-6) Listed on the Canadian DSL (Domestic Substances List) Epoxy General Purpose Laminating Resin Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 05/25/2023 EN (English US) SDS ID: 80LS-25A 8/8 1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2) Listed on the Canadian DSL (Domestic Substances List) EU-Regulations No additional information available National regulations No additional information available 15.3. US State regulations SECTION 16: Other information according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations Revision date : 05/16/2023 Data sources : REGULATION (EC) No 1272/2008 OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 16 December 2008 on classification, labeling and packaging of substances and mixtures, amending and repealing Directives 67/548/EEC and 1999/45/EC, and amending Regulation (EC) No 1907/2006. Other information : None. Full text of H-phrases: H302 Harmful if swallowed H315 Causes skin irritation H317 May cause an allergic skin reaction H319 Causes serious eye irritation H320 Causes eye irritation H332 Harmful if inhaled H402 Harmful to aquatic life NFPA health hazard : 2 - Materials that, under emergency conditions, can cause temporary incapacitation or residual injury. NFPA fire hazard : 1 - Materials that must be preheated before ignition can occur. NFPA reactivity : 0 - Material that in themselves are normally stable, even under fire conditions. Hazard Rating Health : 2 Moderate Hazard - Temporary or minor injury may occur Flammability : 1 Slight Hazard - Materials that must be preheated before ignition will occur. Includes liquids, solids and semi solids having a flash point above 200 F. (Class IIIB) Physical : 0 Minimal Hazard - Materials that are normally stable, even under fire conditions, and will NOT react with water, polymerize, decompose, condense, or self-react. Non-Explosives. Personal protection : H H - Splash goggles, Gloves, Synthetic apron, Vapor respirator SDS US (GHS HazCom 2012) To the best of our knowledge this SDS is accurate. The the extent allowed by law, this statement is made in lieu of an other warranties, expressed or implied including but not limited to any implied warranty of merchantability or fitness for a particular purpose and is in lieu of any other obligations or liability on the part of Dura Technoligies, Inc.

05/25/2023 EN (English US) SDS ID: 80LS-25A Page 1

SECTION 1: Identification

1.1. Identification
Product form : Mixture
Trade name : Epoxy General Purpose Laminating Resin
CAS-No. : Mixture
Product code : 80LS-25A
Formula : mixture

1.2. Recommended use and restrictions on use
Use of the substance/mixture : Epoxy Laminating Resin

1.3. Supplier
Dura Technologies, Inc.
2720 South Willow Avenue #A
Bloomington, CA 92316

909-546-1162
ChemTrec US: 800.424.9300
ChemTrec Int: +1 70 3527 3887

1.4. Emergency telephone number
Emergency number : ChemTrec US: 800.424.9300 Int: +1 70 3527 3887

SECTION 2: Hazard(s) identification

2.1. Classification of the substance or mixture
GHS US classification
Acute toxicity (inhalation) Category 4 H332 Harmful if inhaled
Skin corrosion/irritation Category 2 H315 Causes skin irritation
Serious eye damage/eye irritation Category 2A H319 Causes serious eye irritation
Serious eye damage/eye irritation Category 2B H320 Causes eye irritation
Skin sensitization, Category 1 H317 May cause an allergic skin reaction
Hazardous to the aquatic environment – Acute Hazard Category 3 H402 Harmful to aquatic life

Full text of H statements : see section 16

2.2. GHS Label elements, including precautionary statements
GHS US labeling
Hazard pictograms (GHS US) :

Signal word (GHS US) : Warning
Hazard statements (GHS US) : H315 – Causes skin irritation
H317 – May cause an allergic skin reaction
H319 – Causes serious eye irritation
H320 – Causes eye irritation
H332 – Harmful if inhaled
H402 – Harmful to aquatic life
Precautionary statements (GHS US) : P261 – Avoid breathing dust/fume/gas/mist/vapors/spray.
P264 – Wash hands, forearms and face thoroughly after handling.
P271 – Use only outdoors or in a well-ventilated area.
P272 – Contaminated work clothing must not be allowed out of the workplace.
P273 – Avoid release to the environment.
P280 – Wear protective gloves/protective clothing/eye protection/face protection.
P302+P352 – If on skin: Wash with plenty of water.
P304+P340 – If inhaled: Remove person to fresh air and keep comfortable for breathing.
P305+P351+P338 – IF IN EYES: Rinse cautiously with water for several minutes. Remove
contact lenses, if present and easy to do. Continue rinsing.
P312 – Call a poison center or doctor if you feel unwell.

Epoxy General Purpose Laminating Resin
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

05/25/2023 EN (English US) SDS ID: 80LS-25A 2/8

P321 – Specific treatment (see supplemental first aid instruction on this label).
P332+P313 – If skin irritation occurs: Get medical advice/attention.
P333+P313 – If skin irritation or rash occurs: Get medical advice/attention.
P337+P313 – If eye irritation persists: Get medical advice/attention.
P362+P364 – Take off contaminated clothing and wash it before reuse.
P363 – Wash contaminated clothing before reuse.
P501 – Dispose of contents/container to hazardous or special waste collection point, in
accordance with local, regional, national and/or international regulation.

2.3. Other hazards which do not result in classification
No additional information available
2.4. Unknown acute toxicity (GHS US)
Not applicable
SECTION 3: Composition/Information on ingredients

3.1. Substances
Not applicable
3.2. Mixtures

Name Product identifier % GHS US classification
Propane , 2,2 – bis[p(2,3-epoxypropoxy)phenyl]-, polymers

(CAS-No.) 25085-99-8 <= 88 Skin Irrit. 2, H315 Eye Irrit. 2B, H320 Skin Sens. 1B, H317 1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (CAS-No.) 17557-23-2 <= 11 Skin Irrit. 2, H315 Skin Sens. 1, H317 Aquatic Acute 3, H402 benzyl alcohol (CAS-No.) 100-51-6 <= 8 Acute Tox. 4 (Oral), H302 Acute Tox. 4 (Inhalation), H332 Full text of hazard classes and H-statements : see section 16 SECTION 4: First-aid measures 4.1. Description of first aid measures First-aid measures general : Never give anything by mouth to an unconscious person. If you feel unwell, seek medical advice (show the label where possible). First-aid measures after inhalation : Remove person to fresh air and keep comfortable for breathing. Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or doctor/physician if you feel unwell. Allow affected person to breathe fresh air. Allow the victim to rest. First-aid measures after skin contact : Wash with plenty of soap and water. Wash contaminated clothing before reuse. If skin irritation occurs: Get medical advice/attention. Specific treatment (see supplemental first aid instruction on this label). If skin irritation or rash occurs: Wash skin with plenty of water. First-aid measures after eye contact : Rinse cautiously with water for several minutes. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention. First-aid measures after ingestion : Rinse mouth. Do NOT induce vomiting. Obtain emergency medical attention. Call a poison center/doctor/physician if you feel unwell. 4.2. Most important symptoms and effects (acute and delayed) Potential Adverse human health effects and symptoms : Based on available data, the classification criteria are not met. Symptoms/effects : Causes damage to organs through prolonged or repeated exposure. Symptoms/effects after inhalation : May cause an allergic skin reaction. May cause respiratory irritation. Symptoms/effects after skin contact : Causes skin irritation. Symptoms/effects after eye contact : Causes eye irritation. Causes serious eye irritation. 4.3. Immediate medical attention and special treatment, if necessary Until victim can be cared for by specialized staff: SECTION 5: Fire-fighting measures 5.1. Suitable (and unsuitable) extinguishing media Suitable extinguishing media : Sand. Water spray. Dry powder. Foam. Carbon dioxide. Unsuitable extinguishing media : Do not use a heavy water stream. Epoxy General Purpose Laminating Resin Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 05/25/2023 EN (English US) SDS ID: 80LS-25A 3/8 5.2. Specific hazards arising from the chemical Fire hazard : Heating increases the fire hazard. Heating may cause a fire. Heating may cause a fire or explosion. Insufficient data available on direct fire hazard (flashpoint > 100 C). Self-heating in
large quantities; may catch fire. Temperature above flashpoint: higher fire/explosion hazard.

5.3. Special protective equipment and precautions for fire-fighters
Firefighting instructions : Use water spray or fog for cooling exposed containers. Exercise caution when fighting any
chemical fire. Prevent fire-fighting water from entering environment.
Protection during firefighting : Do not enter fire area without proper protective equipment, including respiratory protection. Do
not attempt to take action without suitable protective equipment. Self-contained breathing
apparatus. Complete protective clothing.
SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures
6.1.1. For non-emergency personnel
Emergency procedures : Ventilate spillage area. Evacuate unnecessary personnel.
6.1.2. For emergency responders
Protective equipment : Do not attempt to take action without suitable protective equipment. Equip cleanup crew with
proper protection. For further information refer to section 8: “Exposure controls/personal
protection”.
Emergency procedures : Ventilate area.

6.2. Environmental precautions
Avoid release to the environment. Prevent entry to sewers and public waters. Notify authorities if liquid enters sewers or public waters.

6.3. Methods and material for containment and cleaning up
For containment : Dam up the liquid spill.
Methods for cleaning up : Take up liquid spill into absorbent material. Soak up spills with inert solids, such as clay or
diatomaceous earth as soon as possible. Collect spillage. Store away from other materials.
Other information : Dispose of materials or solid residues at an authorized site.

6.4. Reference to other sections
See Heading 8. Exposure controls and personal protection. For further information refer to section 13.
SECTION 7: Handling and storage

7.1. Precautions for safe handling
Precautions for safe handling : Wear personal protective equipment. Wash hands and other exposed areas with mild soap and
water before eating, drinking or smoking and when leaving work. Provide good ventilation in
process area to prevent formation of vapor. Avoid breathing dust/fume/gas/mist/vapors/spray.
Use only outdoors or in a well-ventilated area. Do not breathe dust/fume/gas/mist/vapors/spray.
Hygiene measures : Wash hands and other exposed areas with mild soap and water before eat, drink or smoke and
when leaving work. Wash hands, forearms and face thoroughly after handling. Contaminated
work clothing should not be allowed out of the workplace. Wash contaminated clothing before
reuse. Do not eat, drink or smoke when using this product. Always wash hands after handling
the product.

7.2. Conditions for safe storage, including any incompatibilities
Storage conditions : Keep only in the original container in a cool, well ventilated place away from : Keep container
tightly closed. Keep container closed when not in use. Store in a well-ventilated place. Keep
cool.
Incompatible products : Strong bases. Strong acids.
Incompatible materials : Sources of ignition. Direct sunlight.
Storage temperature : 2 – 40 C

SECTION 8: Exposure controls/personal protection

8.1. Control parameters

benzyl alcohol (100-51-6)
Not applicable

1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2)
Not applicable

Epoxy General Purpose Laminating Resin
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

05/25/2023 EN (English US) SDS ID: 80LS-25A 4/8

Propane , 2,2 – bis[p(2,3-epoxypropoxy)phenyl]-, polymers (25085-99-8)
Not applicable

8.2. Appropriate engineering controls
Appropriate engineering controls : Ensure good ventilation of the work station.
Environmental exposure controls : Avoid release to the environment.

8.3. Individual protection measures/Personal protective equipment
Personal protective equipment:
Avoid all unnecessary exposure.

Materials for protective clothing:
GIVE GOOD RESISTANCE: rubber

Hand protection:
Wear protective gloves.

Eye protection:
Chemical goggles or safety glasses. Safety glasses

Skin and body protection:
Wear suitable protective clothing

Respiratory protection:
Wear appropriate mask

Other information:
Do not eat, drink or smoke during use.

SECTION 9: Physical and chemical properties

9.1. Information on basic physical and chemical properties
Physical state : Liquid

Appearance : Liquid.
Color : amber

Odor : slight characteristic

Odor threshold : No data available

pH : No data available

Melting point : N/A

Freezing point : No data available

Boiling point : > 392 F

Flash point : 212 F

Relative evaporation rate (butyl acetate=1) : No data available

Relative evaporation rate (ether=1) : < 1 slower than ether Flammability (solid, gas) : Non flammable. Vapor pressure : <= 3 mm Hg Relative vapor density at 20 C : No data available Relative density : No data available Relative density of saturated gas/air mixture : 1.14 Density : 1.14 kg/l Solubility : Insoluble in water. Log Pow : No data available Auto-ignition temperature : No data available Decomposition temperature : No data available Viscosity, kinematic : No data available Viscosity, dynamic : No data available Epoxy General Purpose Laminating Resin Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 05/25/2023 EN (English US) SDS ID: 80LS-25A 5/8 Explosion limits : No data available Explosive properties : No data available Oxidizing properties : No data available 9.2. Other information No additional information available SECTION 10: Stability and reactivity 10.1. Reactivity The product is non-reactive under normal conditions of use, storage and transport. 10.2. Chemical stability Combustible liquid. Not established. 10.3. Possibility of hazardous reactions Not established. 10.4. Conditions to avoid Open flame. Direct sunlight. Extremely high or low temperatures. 10.5. Incompatible materials Strong acids. Strong bases. 10.6. Hazardous decomposition products fume. Carbon monoxide. Carbon dioxide. SECTION 11: Toxicological information 11.1. Information on toxicological effects Acute toxicity (oral) : Not classified (Lack of data) Acute toxicity (dermal) : Not classified Acute toxicity (inhalation) : Harmful if inhaled. ATE US (gases) 4500 ppmV/4h ATE US (vapors) 11 mg/l/4h ATE US (dust, mist) 1.5 mg/l/4h benzyl alcohol (100-51-6) LD50 oral rat 1620 mg/kg bw/day (Rat, Male, Experimental value, Oral) LD50 dermal rabbit > 2000 mg/kg (Rabbit, Inconclusive, insufficient data, Dermal)
LC50 Inhalation – Rat > 4.178 mg/l air (OECD 403: Acute Inhalation Toxicity, 4 h, Rat, Male / female, Experimental
value, Inhalation (aerosol))
ATE US (oral) 1620 mg/kg body weight
ATE US (gases) 4500 ppmV/4h
ATE US (vapors) 11 mg/l/4h
ATE US (dust, mist) 1.5 mg/l/4h

1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2)
LD50 oral rat 4500 mg/kg (Rat, Literature study, Oral)
LD50 dermal rat > 2100 mg/kg body weight (Rat, Literature study, Dermal)
ATE US (oral) 4500 mg/kg body weight

Skin corrosion/irritation : Causes skin irritation.
Serious eye damage/irritation : Causes serious eye irritation. Causes eye irritation.
Respiratory or skin sensitization : May cause an allergic skin reaction.
Germ cell mutagenicity : Not classified
Carcinogenicity : Not classified

Reproductive toxicity : Not classified
STOT-single exposure : Not classified

STOT-repeated exposure : Not classified

Aspiration hazard : Not classified

Epoxy General Purpose Laminating Resin
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

05/25/2023 EN (English US) SDS ID: 80LS-25A 6/8

Viscosity, kinematic : No data available

Likely routes of exposure : Inhalation.
Potential Adverse human health effects and
symptoms
: Based on available data, the classification criteria are not met.
Symptoms/effects : Causes damage to organs through prolonged or repeated exposure.
Symptoms/effects after inhalation : May cause an allergic skin reaction. May cause respiratory irritation.
Symptoms/effects after skin contact : Causes skin irritation.
Symptoms/effects after eye contact : Causes eye irritation. Causes serious eye irritation.

SECTION 12: Ecological information

12.1. Toxicity
Ecology – general : Dangerous for the environment. Harmful to aquatic life.
Ecology – water : Toxic to aquatic life with long lasting effects.

benzyl alcohol (100-51-6)
LC50 fish 1 460 mg/l (EPA OPP 72-1, 96 h, Pimephales promelas, Static system, Fresh water,
Experimental value, Nominal concentration)
EC50 Daphnia 1 230 mg/l (OECD 202: Daphnia sp. Acute Immobilisation Test, 48 h, Daphnia magna, Fresh
water, Experimental value, GLP)
ErC50 (algae) 770 mg/l (OECD 201: Alga, Growth Inhibition Test, 72 h, Pseudokirchneriella subcapitata,
Static system, Fresh water, Experimental value, GLP)

1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2)
LC50 fish 1 > 100 mg/l (96 h, Pisces, QSAR)
EC50 Daphnia 1 39 – 57 mg/l (OECD 202: Daphnia sp. Acute Immobilisation Test, 48 h, Daphnia magna, Static
system, Fresh water, Experimental value)

12.2. Persistence and degradability
Epoxy General Purpose Laminating Resin (Mixture)
Persistence and degradability May cause long-term adverse effects in the environment.

benzyl alcohol (100-51-6)
Persistence and degradability Biodegradable in the soil. Readily biodegradable in water.
Biochemical oxygen demand (BOD)
1.6 g O /g substance
Chemical oxygen demand (COD)
2.4 g O /g substance
ThOD
2.5 g O /g substance

1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2)
Persistence and degradability Readily biodegradable in water.

12.3. Bioaccumulative potential
Epoxy General Purpose Laminating Resin (Mixture)
Bioaccumulative potential Not established.

benzyl alcohol (100-51-6)
Log Pow 1 – 1.1 (Experimental value, 20 C)
Bioaccumulative potential Low potential for bioaccumulation (Log Kow < 4). 1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2) Log Pow 0.47 (QSAR, KOWWIN, 20 C) Bioaccumulative potential Low potential for bioaccumulation (Log Kow < 4). 12.4. Mobility in soil benzyl alcohol (100-51-6) Surface tension 39 mN/m (20 C) Ecology - soil No (test)data on mobility of the substance available. 1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2) Log Koc 1.22 (log Koc, QSAR) Ecology - soil Highly mobile in soil. Epoxy General Purpose Laminating Resin Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 05/25/2023 EN (English US) SDS ID: 80LS-25A 7/8 12.5. Other adverse effects Other information : Avoid release to the environment. SECTION 13: Disposal considerations 13.1. Disposal methods Regional legislation (waste) : Disposal must be done according to official regulations. Waste treatment methods : Dispose of contents/container in accordance with licensed collector s sorting instructions. Sewage disposal recommendations : Do not discharge into drains. Product/Packaging disposal recommendations : Dispose in a safe manner in accordance with local/national regulations. Dispose of contents/container to hazardous or special waste collection point, in accordance with local, regional, national and/or international regulation. Ecology - waste materials : Avoid release to the environment. SECTION 14: Transport information Department of Transportation (DOT) In accordance with DOT Not regulated Transportation of Dangerous Goods Not regulated Transport by sea Transport document description (IMDG) : UN 3082 ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N. O.S. ( Epoxy Resin ), 9, III, MARINE POLLUTANT UN-No. (IMDG) : 3082 Proper Shipping Name (IMDG) : ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O. S. Class (IMDG) : 9 - Miscellaneous dangerous substances and articles Packing group (IMDG) : III - substances presenting low danger Limited quantities (IMDG) : 5 L Air transport Transport document description (IATA) : UN 3082 Environmentally hazardous substance, liquid, n.o.s. ( Epoxy Resin ), 9, III UN-No. (IATA) : 3082 Proper Shipping Name (IATA) : Environmentally hazardous substance, liquid, n.o.s. Class (IATA) : 9 - Miscellaneous Dangerous Substances and Articles Packing group (IATA) : III - Minor Danger SECTION 15: Regulatory information 15.1. US Federal regulations benzyl alcohol (100-51-6) Listed on the United States TSCA (Toxic Substances Control Act) inventory 1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2) Listed on the United States TSCA (Toxic Substances Control Act) inventory EPA TSCA Regulatory Flag T - T - indicates a substance that is the subject of a final TSCA section 4 test rule. 15.2. International regulations CANADA benzyl alcohol (100-51-6) Listed on the Canadian DSL (Domestic Substances List) Epoxy General Purpose Laminating Resin Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 05/25/2023 EN (English US) SDS ID: 80LS-25A 8/8 1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2) Listed on the Canadian DSL (Domestic Substances List) EU-Regulations No additional information available National regulations No additional information available 15.3. US State regulations SECTION 16: Other information according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations Revision date : 05/16/2023 Data sources : REGULATION (EC) No 1272/2008 OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 16 December 2008 on classification, labeling and packaging of substances and mixtures, amending and repealing Directives 67/548/EEC and 1999/45/EC, and amending Regulation (EC) No 1907/2006. Other information : None. Full text of H-phrases: H302 Harmful if swallowed H315 Causes skin irritation H317 May cause an allergic skin reaction H319 Causes serious eye irritation H320 Causes eye irritation H332 Harmful if inhaled H402 Harmful to aquatic life NFPA health hazard : 2 - Materials that, under emergency conditions, can cause temporary incapacitation or residual injury. NFPA fire hazard : 1 - Materials that must be preheated before ignition can occur. NFPA reactivity : 0 - Material that in themselves are normally stable, even under fire conditions. Hazard Rating Health : 2 Moderate Hazard - Temporary or minor injury may occur Flammability : 1 Slight Hazard - Materials that must be preheated before ignition will occur. Includes liquids, solids and semi solids having a flash point above 200 F. (Class IIIB) Physical : 0 Minimal Hazard - Materials that are normally stable, even under fire conditions, and will NOT react with water, polymerize, decompose, condense, or self-react. Non-Explosives. Personal protection : H H - Splash goggles, Gloves, Synthetic apron, Vapor respirator SDS US (GHS HazCom 2012) To the best of our knowledge this SDS is accurate. The the extent allowed by law, this statement is made in lieu of an other warranties, expressed or implied including but not limited to any implied warranty of merchantability or fitness for a particular purpose and is in lieu of any other obligations or liability on the part of Dura Technoligies, Inc.

05/25/2023 EN (English US) SDS ID: 80LS-25A Page 1

SECTION 1: Identification

1.1. Identification
Product form : Mixture
Trade name : Epoxy General Purpose Laminating Resin
CAS-No. : Mixture
Product code : 80LS-25A
Formula : mixture

1.2. Recommended use and restrictions on use
Use of the substance/mixture : Epoxy Laminating Resin

1.3. Supplier
Dura Technologies, Inc.
2720 South Willow Avenue #A
Bloomington, CA 92316

909-546-1162
ChemTrec US: 800.424.9300
ChemTrec Int: +1 70 3527 3887

1.4. Emergency telephone number
Emergency number : ChemTrec US: 800.424.9300 Int: +1 70 3527 3887

SECTION 2: Hazard(s) identification

2.1. Classification of the substance or mixture
GHS US classification
Acute toxicity (inhalation) Category 4 H332 Harmful if inhaled
Skin corrosion/irritation Category 2 H315 Causes skin irritation
Serious eye damage/eye irritation Category 2A H319 Causes serious eye irritation
Serious eye damage/eye irritation Category 2B H320 Causes eye irritation
Skin sensitization, Category 1 H317 May cause an allergic skin reaction
Hazardous to the aquatic environment – Acute Hazard Category 3 H402 Harmful to aquatic life

Full text of H statements : see section 16

2.2. GHS Label elements, including precautionary statements
GHS US labeling
Hazard pictograms (GHS US) :

Signal word (GHS US) : Warning
Hazard statements (GHS US) : H315 – Causes skin irritation
H317 – May cause an allergic skin reaction
H319 – Causes serious eye irritation
H320 – Causes eye irritation
H332 – Harmful if inhaled
H402 – Harmful to aquatic life
Precautionary statements (GHS US) : P261 – Avoid breathing dust/fume/gas/mist/vapors/spray.
P264 – Wash hands, forearms and face thoroughly after handling.
P271 – Use only outdoors or in a well-ventilated area.
P272 – Contaminated work clothing must not be allowed out of the workplace.
P273 – Avoid release to the environment.
P280 – Wear protective gloves/protective clothing/eye protection/face protection.
P302+P352 – If on skin: Wash with plenty of water.
P304+P340 – If inhaled: Remove person to fresh air and keep comfortable for breathing.
P305+P351+P338 – IF IN EYES: Rinse cautiously with water for several minutes. Remove
contact lenses, if present and easy to do. Continue rinsing.
P312 – Call a poison center or doctor if you feel unwell.

Epoxy General Purpose Laminating Resin
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

05/25/2023 EN (English US) SDS ID: 80LS-25A 2/8

P321 – Specific treatment (see supplemental first aid instruction on this label).
P332+P313 – If skin irritation occurs: Get medical advice/attention.
P333+P313 – If skin irritation or rash occurs: Get medical advice/attention.
P337+P313 – If eye irritation persists: Get medical advice/attention.
P362+P364 – Take off contaminated clothing and wash it before reuse.
P363 – Wash contaminated clothing before reuse.
P501 – Dispose of contents/container to hazardous or special waste collection point, in
accordance with local, regional, national and/or international regulation.

2.3. Other hazards which do not result in classification
No additional information available
2.4. Unknown acute toxicity (GHS US)
Not applicable
SECTION 3: Composition/Information on ingredients

3.1. Substances
Not applicable
3.2. Mixtures

Name Product identifier % GHS US classification
Propane , 2,2 – bis[p(2,3-epoxypropoxy)phenyl]-, polymers

(CAS-No.) 25085-99-8 <= 88 Skin Irrit. 2, H315 Eye Irrit. 2B, H320 Skin Sens. 1B, H317 1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (CAS-No.) 17557-23-2 <= 11 Skin Irrit. 2, H315 Skin Sens. 1, H317 Aquatic Acute 3, H402 benzyl alcohol (CAS-No.) 100-51-6 <= 8 Acute Tox. 4 (Oral), H302 Acute Tox. 4 (Inhalation), H332 Full text of hazard classes and H-statements : see section 16 SECTION 4: First-aid measures 4.1. Description of first aid measures First-aid measures general : Never give anything by mouth to an unconscious person. If you feel unwell, seek medical advice (show the label where possible). First-aid measures after inhalation : Remove person to fresh air and keep comfortable for breathing. Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or doctor/physician if you feel unwell. Allow affected person to breathe fresh air. Allow the victim to rest. First-aid measures after skin contact : Wash with plenty of soap and water. Wash contaminated clothing before reuse. If skin irritation occurs: Get medical advice/attention. Specific treatment (see supplemental first aid instruction on this label). If skin irritation or rash occurs: Wash skin with plenty of water. First-aid measures after eye contact : Rinse cautiously with water for several minutes. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention. First-aid measures after ingestion : Rinse mouth. Do NOT induce vomiting. Obtain emergency medical attention. Call a poison center/doctor/physician if you feel unwell. 4.2. Most important symptoms and effects (acute and delayed) Potential Adverse human health effects and symptoms : Based on available data, the classification criteria are not met. Symptoms/effects : Causes damage to organs through prolonged or repeated exposure. Symptoms/effects after inhalation : May cause an allergic skin reaction. May cause respiratory irritation. Symptoms/effects after skin contact : Causes skin irritation. Symptoms/effects after eye contact : Causes eye irritation. Causes serious eye irritation. 4.3. Immediate medical attention and special treatment, if necessary Until victim can be cared for by specialized staff: SECTION 5: Fire-fighting measures 5.1. Suitable (and unsuitable) extinguishing media Suitable extinguishing media : Sand. Water spray. Dry powder. Foam. Carbon dioxide. Unsuitable extinguishing media : Do not use a heavy water stream. Epoxy General Purpose Laminating Resin Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 05/25/2023 EN (English US) SDS ID: 80LS-25A 3/8 5.2. Specific hazards arising from the chemical Fire hazard : Heating increases the fire hazard. Heating may cause a fire. Heating may cause a fire or explosion. Insufficient data available on direct fire hazard (flashpoint > 100 C). Self-heating in
large quantities; may catch fire. Temperature above flashpoint: higher fire/explosion hazard.

5.3. Special protective equipment and precautions for fire-fighters
Firefighting instructions : Use water spray or fog for cooling exposed containers. Exercise caution when fighting any
chemical fire. Prevent fire-fighting water from entering environment.
Protection during firefighting : Do not enter fire area without proper protective equipment, including respiratory protection. Do
not attempt to take action without suitable protective equipment. Self-contained breathing
apparatus. Complete protective clothing.
SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures
6.1.1. For non-emergency personnel
Emergency procedures : Ventilate spillage area. Evacuate unnecessary personnel.
6.1.2. For emergency responders
Protective equipment : Do not attempt to take action without suitable protective equipment. Equip cleanup crew with
proper protection. For further information refer to section 8: “Exposure controls/personal
protection”.
Emergency procedures : Ventilate area.

6.2. Environmental precautions
Avoid release to the environment. Prevent entry to sewers and public waters. Notify authorities if liquid enters sewers or public waters.

6.3. Methods and material for containment and cleaning up
For containment : Dam up the liquid spill.
Methods for cleaning up : Take up liquid spill into absorbent material. Soak up spills with inert solids, such as clay or
diatomaceous earth as soon as possible. Collect spillage. Store away from other materials.
Other information : Dispose of materials or solid residues at an authorized site.

6.4. Reference to other sections
See Heading 8. Exposure controls and personal protection. For further information refer to section 13.
SECTION 7: Handling and storage

7.1. Precautions for safe handling
Precautions for safe handling : Wear personal protective equipment. Wash hands and other exposed areas with mild soap and
water before eating, drinking or smoking and when leaving work. Provide good ventilation in
process area to prevent formation of vapor. Avoid breathing dust/fume/gas/mist/vapors/spray.
Use only outdoors or in a well-ventilated area. Do not breathe dust/fume/gas/mist/vapors/spray.
Hygiene measures : Wash hands and other exposed areas with mild soap and water before eat, drink or smoke and
when leaving work. Wash hands, forearms and face thoroughly after handling. Contaminated
work clothing should not be allowed out of the workplace. Wash contaminated clothing before
reuse. Do not eat, drink or smoke when using this product. Always wash hands after handling
the product.

7.2. Conditions for safe storage, including any incompatibilities
Storage conditions : Keep only in the original container in a cool, well ventilated place away from : Keep container
tightly closed. Keep container closed when not in use. Store in a well-ventilated place. Keep
cool.
Incompatible products : Strong bases. Strong acids.
Incompatible materials : Sources of ignition. Direct sunlight.
Storage temperature : 2 – 40 C

SECTION 8: Exposure controls/personal protection

8.1. Control parameters

benzyl alcohol (100-51-6)
Not applicable

1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2)
Not applicable

Epoxy General Purpose Laminating Resin
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

05/25/2023 EN (English US) SDS ID: 80LS-25A 4/8

Propane , 2,2 – bis[p(2,3-epoxypropoxy)phenyl]-, polymers (25085-99-8)
Not applicable

8.2. Appropriate engineering controls
Appropriate engineering controls : Ensure good ventilation of the work station.
Environmental exposure controls : Avoid release to the environment.

8.3. Individual protection measures/Personal protective equipment
Personal protective equipment:
Avoid all unnecessary exposure.

Materials for protective clothing:
GIVE GOOD RESISTANCE: rubber

Hand protection:
Wear protective gloves.

Eye protection:
Chemical goggles or safety glasses. Safety glasses

Skin and body protection:
Wear suitable protective clothing

Respiratory protection:
Wear appropriate mask

Other information:
Do not eat, drink or smoke during use.

SECTION 9: Physical and chemical properties

9.1. Information on basic physical and chemical properties
Physical state : Liquid

Appearance : Liquid.
Color : amber

Odor : slight characteristic

Odor threshold : No data available

pH : No data available

Melting point : N/A

Freezing point : No data available

Boiling point : > 392 F

Flash point : 212 F

Relative evaporation rate (butyl acetate=1) : No data available

Relative evaporation rate (ether=1) : < 1 slower than ether Flammability (solid, gas) : Non flammable. Vapor pressure : <= 3 mm Hg Relative vapor density at 20 C : No data available Relative density : No data available Relative density of saturated gas/air mixture : 1.14 Density : 1.14 kg/l Solubility : Insoluble in water. Log Pow : No data available Auto-ignition temperature : No data available Decomposition temperature : No data available Viscosity, kinematic : No data available Viscosity, dynamic : No data available Epoxy General Purpose Laminating Resin Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 05/25/2023 EN (English US) SDS ID: 80LS-25A 5/8 Explosion limits : No data available Explosive properties : No data available Oxidizing properties : No data available 9.2. Other information No additional information available SECTION 10: Stability and reactivity 10.1. Reactivity The product is non-reactive under normal conditions of use, storage and transport. 10.2. Chemical stability Combustible liquid. Not established. 10.3. Possibility of hazardous reactions Not established. 10.4. Conditions to avoid Open flame. Direct sunlight. Extremely high or low temperatures. 10.5. Incompatible materials Strong acids. Strong bases. 10.6. Hazardous decomposition products fume. Carbon monoxide. Carbon dioxide. SECTION 11: Toxicological information 11.1. Information on toxicological effects Acute toxicity (oral) : Not classified (Lack of data) Acute toxicity (dermal) : Not classified Acute toxicity (inhalation) : Harmful if inhaled. ATE US (gases) 4500 ppmV/4h ATE US (vapors) 11 mg/l/4h ATE US (dust, mist) 1.5 mg/l/4h benzyl alcohol (100-51-6) LD50 oral rat 1620 mg/kg bw/day (Rat, Male, Experimental value, Oral) LD50 dermal rabbit > 2000 mg/kg (Rabbit, Inconclusive, insufficient data, Dermal)
LC50 Inhalation – Rat > 4.178 mg/l air (OECD 403: Acute Inhalation Toxicity, 4 h, Rat, Male / female, Experimental
value, Inhalation (aerosol))
ATE US (oral) 1620 mg/kg body weight
ATE US (gases) 4500 ppmV/4h
ATE US (vapors) 11 mg/l/4h
ATE US (dust, mist) 1.5 mg/l/4h

1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2)
LD50 oral rat 4500 mg/kg (Rat, Literature study, Oral)
LD50 dermal rat > 2100 mg/kg body weight (Rat, Literature study, Dermal)
ATE US (oral) 4500 mg/kg body weight

Skin corrosion/irritation : Causes skin irritation.
Serious eye damage/irritation : Causes serious eye irritation. Causes eye irritation.
Respiratory or skin sensitization : May cause an allergic skin reaction.
Germ cell mutagenicity : Not classified
Carcinogenicity : Not classified

Reproductive toxicity : Not classified
STOT-single exposure : Not classified

STOT-repeated exposure : Not classified

Aspiration hazard : Not classified

Epoxy General Purpose Laminating Resin
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

05/25/2023 EN (English US) SDS ID: 80LS-25A 6/8

Viscosity, kinematic : No data available

Likely routes of exposure : Inhalation.
Potential Adverse human health effects and
symptoms
: Based on available data, the classification criteria are not met.
Symptoms/effects : Causes damage to organs through prolonged or repeated exposure.
Symptoms/effects after inhalation : May cause an allergic skin reaction. May cause respiratory irritation.
Symptoms/effects after skin contact : Causes skin irritation.
Symptoms/effects after eye contact : Causes eye irritation. Causes serious eye irritation.

SECTION 12: Ecological information

12.1. Toxicity
Ecology – general : Dangerous for the environment. Harmful to aquatic life.
Ecology – water : Toxic to aquatic life with long lasting effects.

benzyl alcohol (100-51-6)
LC50 fish 1 460 mg/l (EPA OPP 72-1, 96 h, Pimephales promelas, Static system, Fresh water,
Experimental value, Nominal concentration)
EC50 Daphnia 1 230 mg/l (OECD 202: Daphnia sp. Acute Immobilisation Test, 48 h, Daphnia magna, Fresh
water, Experimental value, GLP)
ErC50 (algae) 770 mg/l (OECD 201: Alga, Growth Inhibition Test, 72 h, Pseudokirchneriella subcapitata,
Static system, Fresh water, Experimental value, GLP)

1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2)
LC50 fish 1 > 100 mg/l (96 h, Pisces, QSAR)
EC50 Daphnia 1 39 – 57 mg/l (OECD 202: Daphnia sp. Acute Immobilisation Test, 48 h, Daphnia magna, Static
system, Fresh water, Experimental value)

12.2. Persistence and degradability
Epoxy General Purpose Laminating Resin (Mixture)
Persistence and degradability May cause long-term adverse effects in the environment.

benzyl alcohol (100-51-6)
Persistence and degradability Biodegradable in the soil. Readily biodegradable in water.
Biochemical oxygen demand (BOD)
1.6 g O /g substance
Chemical oxygen demand (COD)
2.4 g O /g substance
ThOD
2.5 g O /g substance

1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2)
Persistence and degradability Readily biodegradable in water.

12.3. Bioaccumulative potential
Epoxy General Purpose Laminating Resin (Mixture)
Bioaccumulative potential Not established.

benzyl alcohol (100-51-6)
Log Pow 1 – 1.1 (Experimental value, 20 C)
Bioaccumulative potential Low potential for bioaccumulation (Log Kow < 4). 1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2) Log Pow 0.47 (QSAR, KOWWIN, 20 C) Bioaccumulative potential Low potential for bioaccumulation (Log Kow < 4). 12.4. Mobility in soil benzyl alcohol (100-51-6) Surface tension 39 mN/m (20 C) Ecology - soil No (test)data on mobility of the substance available. 1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2) Log Koc 1.22 (log Koc, QSAR) Ecology - soil Highly mobile in soil. Epoxy General Purpose Laminating Resin Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 05/25/2023 EN (English US) SDS ID: 80LS-25A 7/8 12.5. Other adverse effects Other information : Avoid release to the environment. SECTION 13: Disposal considerations 13.1. Disposal methods Regional legislation (waste) : Disposal must be done according to official regulations. Waste treatment methods : Dispose of contents/container in accordance with licensed collector s sorting instructions. Sewage disposal recommendations : Do not discharge into drains. Product/Packaging disposal recommendations : Dispose in a safe manner in accordance with local/national regulations. Dispose of contents/container to hazardous or special waste collection point, in accordance with local, regional, national and/or international regulation. Ecology - waste materials : Avoid release to the environment. SECTION 14: Transport information Department of Transportation (DOT) In accordance with DOT Not regulated Transportation of Dangerous Goods Not regulated Transport by sea Transport document description (IMDG) : UN 3082 ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N. O.S. ( Epoxy Resin ), 9, III, MARINE POLLUTANT UN-No. (IMDG) : 3082 Proper Shipping Name (IMDG) : ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O. S. Class (IMDG) : 9 - Miscellaneous dangerous substances and articles Packing group (IMDG) : III - substances presenting low danger Limited quantities (IMDG) : 5 L Air transport Transport document description (IATA) : UN 3082 Environmentally hazardous substance, liquid, n.o.s. ( Epoxy Resin ), 9, III UN-No. (IATA) : 3082 Proper Shipping Name (IATA) : Environmentally hazardous substance, liquid, n.o.s. Class (IATA) : 9 - Miscellaneous Dangerous Substances and Articles Packing group (IATA) : III - Minor Danger SECTION 15: Regulatory information 15.1. US Federal regulations benzyl alcohol (100-51-6) Listed on the United States TSCA (Toxic Substances Control Act) inventory 1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2) Listed on the United States TSCA (Toxic Substances Control Act) inventory EPA TSCA Regulatory Flag T - T - indicates a substance that is the subject of a final TSCA section 4 test rule. 15.2. International regulations CANADA benzyl alcohol (100-51-6) Listed on the Canadian DSL (Domestic Substances List) Epoxy General Purpose Laminating Resin Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 05/25/2023 EN (English US) SDS ID: 80LS-25A 8/8 1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (17557-23-2) Listed on the Canadian DSL (Domestic Substances List) EU-Regulations No additional information available National regulations No additional information available 15.3. US State regulations SECTION 16: Other information according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations Revision date : 05/16/2023 Data sources : REGULATION (EC) No 1272/2008 OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 16 December 2008 on classification, labeling and packaging of substances and mixtures, amending and repealing Directives 67/548/EEC and 1999/45/EC, and amending Regulation (EC) No 1907/2006. Other information : None. Full text of H-phrases: H302 Harmful if swallowed H315 Causes skin irritation H317 May cause an allergic skin reaction H319 Causes serious eye irritation H320 Causes eye irritation H332 Harmful if inhaled H402 Harmful to aquatic life NFPA health hazard : 2 - Materials that, under emergency conditions, can cause temporary incapacitation or residual injury. NFPA fire hazard : 1 - Materials that must be preheated before ignition can occur. NFPA reactivity : 0 - Material that in themselves are normally stable, even under fire conditions. Hazard Rating Health : 2 Moderate Hazard - Temporary or minor injury may occur Flammability : 1 Slight Hazard - Materials that must be preheated before ignition will occur. Includes liquids, solids and semi solids having a flash point above 200 F. (Class IIIB) Physical : 0 Minimal Hazard - Materials that are normally stable, even under fire conditions, and will NOT react with water, polymerize, decompose, condense, or self-react. Non-Explosives. Personal protection : H H - Splash goggles, Gloves, Synthetic apron, Vapor respirator SDS US (GHS HazCom 2012) To the best of our knowledge this SDS is accurate. The the extent allowed by law, this statement is made in lieu of an other warranties, expressed or implied including but not limited to any implied warranty of merchantability or fitness for a particular purpose and is in lieu of any other obligations or liability on the part of Dura Technoligies, Inc.

05/25/2023 EN (English US) SDS ID: 80LS-22B Page 1

SECTION 1: Identification

1.1. Identification
Product form : Mixture
Trade name : Epoxy General Purpose Laminating Hardener
CAS-No. : Mixture
Product code : 80LS-22B
Other means of identification : Epoxy Part B

1.2. Recommended use and restrictions on use
Use of the substance/mixture : Hardener

1.3. Supplier
Dura Technologies, Inc.
2720 South Willow Avenue #A
Bloomington, CA 92316

909-546-1162
ChemTrec US: 800.424.9300
ChemTrec Int: +1 70 3527 3887

1.4. Emergency telephone number
Emergency number : ChemTrec US: 800.424.9300 Int: +1 70 3527 3887

SECTION 2: Hazard(s) identification

2.1. Classification of the substance or mixture
GHS US classification
Acute toxicity (oral) Category 4 H302 Harmful if swallowed
Acute toxicity (dermal) Category 4 H312 Harmful in contact with skin
Skin corrosion/irritation Category 1B H314 Causes severe skin burns and eye damage
Serious eye damage/eye irritation Category 1 H318 Causes serious eye damage
Skin sensitization, category 1A H317 May cause an allergic skin reaction
Hazardous to the aquatic environment – Acute Hazard Category 3 H402 Harmful to aquatic life
Hazardous to the aquatic environment – Chronic Hazard Category 2 H411 Toxic to aquatic life with long lasting effects

Full text of H statements : see section 16

2.2. GHS Label elements, including precautionary statements
GHS US labeling
Hazard pictograms (GHS US) :

Signal word (GHS US) : Danger
Hazard statements (GHS US) : H302+H312 – Harmful if swallowed or in contact with skin
H314 – Causes severe skin burns and eye damage
H317 – May cause an allergic skin reaction
H318 – Causes serious eye damage
H402 – Harmful to aquatic life
H411 – Toxic to aquatic life with long lasting effects
Precautionary statements (GHS US) : P260 – Do not breathe dust/fume/gas/mist/vapors/spray.
P261 – Avoid breathing dust/fume/gas/mist/vapors/spray.
P264 – Wash hands, forearms and face thoroughly after handling.
P270 – Do not eat, drink or smoke when using this product.
P272 – Contaminated work clothing must not be allowed out of the workplace.
P273 – Avoid release to the environment.
P280 – Wear protective clothing.
P301+P312 – If swallowed: Call a poison center or doctor if you feel unwell.
P301+P330+P331 – If swallowed: rinse mouth. Do NOT induce vomiting.
P302+P352 – If on skin: Wash with plenty of water.

Epoxy General Purpose Laminating Hardener
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

05/25/2023 EN (English US) SDS ID: 80LS-22B 2/12

P303+P361+P353 – If on skin (or hair): Take off immediately all contaminated clothing. Rinse
skin with water/shower.
P304+P340 – If inhaled: Remove person to fresh air and keep comfortable for breathing.
P305+P351+P338 – IF IN EYES: Rinse cautiously with water for several minutes. Remove
contact lenses, if present and easy to do. Continue rinsing.
P310 – Immediately call a poison center or doctor.
P312 – Call a poison center or doctor if you feel unwell.
P321 – Specific treatment (see supplemental first aid instruction on this label).
P322 – Specific treatment (see supplemental first aid instruction on this label)
P330 – Rinse mouth.
P333+P313 – If skin irritation or rash occurs: Get medical advice/attention.
P362+P364 – Take off contaminated clothing and wash it before reuse.
P363 – Wash contaminated clothing before reuse.
P391 – Collect spillage.
P405 – Store locked up.
P501 – Dispose of contents/container to hazardous or special waste collection point, in
accordance with local, regional, national and/or international regulation.

2.3. Other hazards which do not result in classification
No additional information available
2.4. Unknown acute toxicity (GHS US)
Not applicable
SECTION 3: Composition/Information on ingredients

3.1. Substances
Not applicable
3.2. Mixtures

Name Product identifier % GHS US classification
alpha-hydro-omega(2-aminomethylethoxy)poly(oxy(methyl-
1,2-ethanediyl)ether with 2-ethyl-2-(hydroxymethyl)-1,3-
propanediol (3:1)

(CAS-No.) 39423-51-3 <= 43 Acute Tox. 3 (Oral), H301 Acute Tox. 3 (Dermal), H311 Skin Corr. 1, H314 triethylenetetramine (CAS-No.) 112-24-3 <= 23 Acute Tox. 3 (Dermal), H311 Skin Corr. 1B, H314 Skin Sens. 1, H317 Aquatic Acute 3, H402 Aquatic Chronic 3, H412 4-nonylphenol, branched (CAS-No.) 84852-15-3 <= 13 Acute Tox. 4 (Oral), H302 Skin Corr. 1B, H314 Aquatic Acute 1, H400 Aquatic Chronic 1, H410 Polyamide Curing Agent (CAS-No.) MIXTURE <= 8 Skin Irrit. 2, H315 Eye Irrit. 2, H319 Skin Sens. 1, H317 benzyl alcohol (CAS-No.) 100-51-6 <= 7 Acute Tox. 4 (Oral), H302 Acute Tox. 4 (Inhalation), H332 2-piperazin-1-ylethylamine (CAS-No.) 140-31-8 <= 2 Acute Tox. 3 (Dermal), H311 Skin Corr. 1, H314 Skin Sens. 1, H317 Aquatic Acute 3, H402 Aquatic Chronic 3, H412 2-(2-aminoethylamino)ethanol, (AEEA) (CAS-No.) 111-41-1 <= 2 Skin Corr. 1B, H314 Eye Dam. 1, H318 Skin Sens. 1, H317 Repr. 1B, H360 STOT SE 3, H335 3,6,9-triazaundecamethylenediamine, tetraethylenepentamine (CAS-No.) 112-57-2 <= 1 Acute Tox. 4 (Oral), H302 Acute Tox. 4 (Dermal), H312 Skin Corr. 1B, H314 Skin Sens. 1, H317 Aquatic Chronic 2, H411 2,2'-iminodiethylamine, diethylenetriamine (CAS-No.) 111-40-0 <= 1 Acute Tox. 4 (Oral), H302 Acute Tox. 4 (Dermal), H312 Skin Corr. 1B, H314 Skin Sens. 1, H317 Epoxy General Purpose Laminating Hardener Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 05/25/2023 EN (English US) SDS ID: 80LS-22B 3/12 Full text of hazard classes and H-statements : see section 16 SECTION 4: First-aid measures 4.1. Description of first aid measures First-aid measures general : Never give anything by mouth to an unconscious person. If you feel unwell, seek medical advice (show the label where possible). First-aid measures after inhalation : Remove person to fresh air and keep comfortable for breathing. Remove victim to fresh air and keep at rest in a position comfortable for breathing. Immediately call a poison center or doctor/physician. First-aid measures after skin contact : Immediately call a poison center or doctor/physician. Specific measures (see supplemental first aid instruction on this label). Wash with plenty of soap and water. Wash contaminated clothing before reuse. Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower. If skin irritation or rash occurs: Get medical advice/attention. Specific treatment (see supplemental first aid instruction on this label). First-aid measures after eye contact : Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a poison center or doctor/physician. First-aid measures after ingestion : Rinse mouth. Do NOT induce vomiting. Call a POISON CENTER or doctor/physician if you feel unwell. Immediately call a poison center or doctor/physician. Call a poison center/doctor/physician if you feel unwell. 4.2. Most important symptoms and effects (acute and delayed) Potential Adverse human health effects and symptoms : Harmful if swallowed. Harmful in contact with skin. Symptoms/effects : Causes severe skin burns and eye damage. Symptoms/effects after inhalation : Harmful if inhaled. May cause an allergic skin reaction. Symptoms/effects after skin contact : Caustic burns/corrosion of the skin. Repeated exposure to this material can result in absorption through skin causing significant health hazard. Harmful in contact with skin. Symptoms/effects after eye contact : Causes eye irritation. Causes serious eye damage. May cause severe irritation. Symptoms/effects after ingestion : Swallowing a small quantity of this material will result in serious health hazard. 4.3. Immediate medical attention and special treatment, if necessary Until victim can be cared for by specialized staff: SECTION 5: Fire-fighting measures 5.1. Suitable (and unsuitable) extinguishing media Suitable extinguishing media : Sand. Water spray. Dry powder. Foam. Carbon dioxide. Unsuitable extinguishing media : Do not use a heavy water stream. 5.2. Specific hazards arising from the chemical Fire hazard : Heating increases the fire hazard. Heating may cause a fire. Heating may cause a fire or explosion. Insufficient data available on direct fire hazard (flashpoint > 100 C). Self-heating in
large quantities; may catch fire. Temperature above flashpoint: higher fire/explosion hazard.

5.3. Special protective equipment and precautions for fire-fighters
Firefighting instructions : Use water spray or fog for cooling exposed containers. Exercise caution when fighting any
chemical fire. Prevent fire-fighting water from entering environment.
Protection during firefighting : Do not enter fire area without proper protective equipment, including respiratory protection. Do
not attempt to take action without suitable protective equipment. Self-contained breathing
apparatus. Complete protective clothing.
SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures
6.1.1. For non-emergency personnel
Emergency procedures : Ventilate spillage area. Evacuate unnecessary personnel.
6.1.2. For emergency responders
Protective equipment : Do not attempt to take action without suitable protective equipment. Equip cleanup crew with
proper protection. For further information refer to section 8: “Exposure controls/personal
protection”.
Emergency procedures : Ventilate area.

6.2. Environmental precautions
Avoid release to the environment. Prevent entry to sewers and public waters. Notify authorities if liquid enters sewers or public waters.

Epoxy General Purpose Laminating Hardener
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

05/25/2023 EN (English US) SDS ID: 80LS-22B 4/12

6.3. Methods and material for containment and cleaning up
Methods for cleaning up : Take up liquid spill into absorbent material. Soak up spills with inert solids, such as clay or
diatomaceous earth as soon as possible. Collect spillage. Store away from other materials.
Other information : Dispose of materials or solid residues at an authorized site.

6.4. Reference to other sections
See Heading 8. Exposure controls and personal protection. For further information refer to section 13.
SECTION 7: Handling and storage

7.1. Precautions for safe handling
Precautions for safe handling : Ensure good ventilation of the work station. Wear personal protective equipment. Wash hands
and other exposed areas with mild soap and water before eating, drinking or smoking and
when leaving work. Provide good ventilation in process area to prevent formation of vapor. Do
not breathe dust/fume/gas/mist/vapors/spray. Avoid breathing dust/fume/gas/mist/vapors/spray.
Hygiene measures : Wash hands, forearms and face thoroughly after handling. Wash contaminated clothing before
reuse. Contaminated work clothing should not be allowed out of the workplace. Do not eat,
drink or smoke when using this product. Always wash hands after handling the product.

7.2. Conditions for safe storage, including any incompatibilities
Technical measures : Comply with applicable regulations.
Storage conditions : Keep only in the original container in a cool, well ventilated place away from : Keep container
closed when not in use. Store in a well-ventilated place. Keep cool.
Incompatible products : Strong bases. Strong acids.
Incompatible materials : Sources of ignition. Direct sunlight.

SECTION 8: Exposure controls/personal protection

8.1. Control parameters

triethylenetetramine (112-24-3)
Not applicable

alpha-hydro-omega(2-aminomethylethoxy)poly(oxy(methyl-1,2-ethanediyl)ether with 2-ethyl-2-(hydroxymethyl)-1,3-propanediol (3:1)
(39423-51-3)
Not applicable

Polyamide Curing Agent (MIXTURE)
Not applicable

benzyl alcohol (100-51-6)
Not applicable

2-piperazin-1-ylethylamine (140-31-8)
Not applicable

2-(2-aminoethylamino)ethanol, (AEEA) (111-41-1)
Not applicable

3,6,9-triazaundecamethylenediamine, tetraethylenepentamine (112-57-2)
Not applicable

2,2′-iminodiethylamine, diethylenetriamine (111-40-0)
Not applicable

4-nonylphenol, branched (84852-15-3)
Not applicable

8.2. Appropriate engineering controls
Appropriate engineering controls : Ensure good ventilation of the work station.
Environmental exposure controls : Avoid release to the environment.

8.3. Individual protection measures/Personal protective equipment
Personal protective equipment:
Avoid all unnecessary exposure.

Hand protection:

Epoxy General Purpose Laminating Hardener
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

05/25/2023 EN (English US) SDS ID: 80LS-22B 5/12

Wear protective gloves.

Eye protection:
Chemical goggles or face shield. Safety glasses

Skin and body protection:
Wear suitable protective clothing

Respiratory protection:
Wear appropriate mask

Other information:
Do not eat, drink or smoke during use.

SECTION 9: Physical and chemical properties

9.1. Information on basic physical and chemical properties
Physical state : Liquid

Appearance : clear.
Color : clear

Odor : characteristic

Odor threshold : No data available

pH : No data available

Melting point : Not applicable

Freezing point : No data available

Boiling point : > 392 F

Flash point : > 212 F

Relative evaporation rate (butyl acetate=1) : No data available

Relative evaporation rate (ether=1) : < 1 slower than ether Flammability (solid, gas) : Non flammable. Vapor pressure : <= 4.3 mm Hg Relative vapor density at 20 C : No data available Relative density : No data available Density : 0.98 kg/l Solubility : No data available Log Pow : No data available Auto-ignition temperature : No data available Decomposition temperature : No data available Viscosity, kinematic : No data available Viscosity, dynamic : No data available Explosion limits : No data available Explosive properties : No data available Oxidizing properties : No data available 9.2. Other information No additional information available SECTION 10: Stability and reactivity 10.1. Reactivity Thermal decomposition generates : Corrosive vapors. 10.2. Chemical stability Stable under normal conditions. Not established. 10.3. Possibility of hazardous reactions Not established. 10.4. Conditions to avoid Direct sunlight. Extremely high or low temperatures. Epoxy General Purpose Laminating Hardener Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 05/25/2023 EN (English US) SDS ID: 80LS-22B 6/12 10.5. Incompatible materials Strong acids. Strong bases. 10.6. Hazardous decomposition products fume. Carbon monoxide. Carbon dioxide. Thermal decomposition generates : Corrosive vapors. SECTION 11: Toxicological information 11.1. Information on toxicological effects Acute toxicity (oral) : Harmful if swallowed. Acute toxicity (dermal) : Harmful in contact with skin. Acute toxicity (inhalation) : Not classified ATE US (oral) 425.206 mg/kg body weight ATE US (dermal) 1100 mg/kg body weight triethylenetetramine (112-24-3) LD50 oral rat 2500 mg/kg (Rat, Literature, Oral) LD50 dermal rabbit 805 mg/kg (Rabbit, Literature, Dermal) ATE US (oral) 2500 mg/kg body weight ATE US (dermal) 805 mg/kg body weight alpha-hydro-omega(2-aminomethylethoxy)poly(oxy(methyl-1,2-ethanediyl)ether with 2-ethyl-2-(hydroxymethyl)-1,3-propanediol (3:1) (39423-51-3) LD50 oral rat 220 mg/kg (Rat) LD50 dermal rabbit 401 mg/kg (Rabbit) ATE US (oral) 220 mg/kg body weight ATE US (dermal) 401 mg/kg body weight benzyl alcohol (100-51-6) LD50 oral rat 1620 mg/kg bw/day (Rat, Male, Experimental value, Oral) LD50 dermal rabbit > 2000 mg/kg (Rabbit, Inconclusive, insufficient data, Dermal)
LC50 Inhalation – Rat > 4.178 mg/l air (OECD 403: Acute Inhalation Toxicity, 4 h, Rat, Male / female, Experimental
value, Inhalation (aerosol))
ATE US (oral) 1620 mg/kg body weight
ATE US (gases) 4500 ppmV/4h
ATE US (vapors) 11 mg/l/4h
ATE US (dust, mist) 1.5 mg/l/4h

2-piperazin-1-ylethylamine (140-31-8)
LD50 oral rat 2097 mg/kg body weight (Rat, Male, Experimental value, Oral, 14 day(s))
LD50 dermal rabbit 866 mg/kg bw/day (24 h, Rabbit, Male, Experimental value, Dermal, 14 day(s))
ATE US (oral) 2097 mg/kg body weight
ATE US (dermal) 866 mg/kg body weight

3,6,9-triazaundecamethylenediamine, tetraethylenepentamine (112-57-2)
ATE US (oral) 500 mg/kg body weight
ATE US (dermal) 1100 mg/kg body weight

2,2′-iminodiethylamine, diethylenetriamine (111-40-0)
ATE US (oral) 500 mg/kg body weight
ATE US (dermal) 1100 mg/kg body weight

4-nonylphenol, branched (84852-15-3)
ATE US (oral) 500 mg/kg body weight

Skin corrosion/irritation : Causes severe skin burns and eye damage.
Serious eye damage/irritation : Causes serious eye damage.
Respiratory or skin sensitization : May cause an allergic skin reaction.
Germ cell mutagenicity : Not classified
Carcinogenicity : Not classified

Reproductive toxicity : Not classified

Epoxy General Purpose Laminating Hardener
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

05/25/2023 EN (English US) SDS ID: 80LS-22B 7/12

STOT-single exposure : Not classified

2-(2-aminoethylamino)ethanol, (AEEA) (111-41-1)
STOT-single exposure May cause respiratory irritation.

STOT-repeated exposure : Not classified

Aspiration hazard : Not classified
Viscosity, kinematic : No data available

Likely routes of exposure : Inhalation.
Potential Adverse human health effects and
symptoms
: Harmful if swallowed. Harmful in contact with skin.
Symptoms/effects : Causes severe skin burns and eye damage.
Symptoms/effects after inhalation : Harmful if inhaled. May cause an allergic skin reaction.
Symptoms/effects after skin contact : Caustic burns/corrosion of the skin. Repeated exposure to this material can result in absorption
through skin causing significant health hazard. Harmful in contact with skin.
Symptoms/effects after eye contact : Causes eye irritation. Causes serious eye damage. May cause severe irritation.
Symptoms/effects after ingestion : Swallowing a small quantity of this material will result in serious health hazard.

SECTION 12: Ecological information

12.1. Toxicity
Ecology – general : Harmful to aquatic life. Dangerous for the environment.
Ecology – water : Harmful to aquatic life. Toxic to aquatic life with long lasting effects. Harmful to aquatic life with
long lasting effects.

triethylenetetramine (112-24-3)
LC50 fish 1 495 mg/l (96 h, Pimephales promelas, Fresh water, Literature study)
EC50 Daphnia 1 31.1 mg/l (Equivalent or similar to OECD 202, 48 h, Daphnia magna, Literature study)
ErC50 (algae) >= 100 mg/l (DIN 38412-9, 72 h, Scenedesmus subspicatus, Literature study, Growth)

benzyl alcohol (100-51-6)
LC50 fish 1 460 mg/l (EPA OPP 72-1, 96 h, Pimephales promelas, Static system, Fresh water,
Experimental value, Nominal concentration)
EC50 Daphnia 1 230 mg/l (OECD 202: Daphnia sp. Acute Immobilisation Test, 48 h, Daphnia magna, Fresh
water, Experimental value, GLP)
ErC50 (algae) 770 mg/l (OECD 201: Alga, Growth Inhibition Test, 72 h, Pseudokirchneriella subcapitata,
Static system, Fresh water, Experimental value, GLP)

2-piperazin-1-ylethylamine (140-31-8)
LC50 fish 1 2190 mg/l (96 h, Pimephales promelas, Static system, Fresh water, Experimental value)
EC50 Daphnia 1 58 mg/l (OECD 202: Daphnia sp. Acute Immobilisation Test, 48 h, Daphnia magna, Static
system, Experimental value, GLP)
ErC50 (algae) > 1000 mg/l (OECD 201: Alga, Growth Inhibition Test, 72 h, Pseudokirchneriella subcapitata,
Fresh water, Experimental value, GLP)

12.2. Persistence and degradability
Epoxy General Purpose Laminating Hardener (Mixture)
Persistence and degradability May cause long-term adverse effects in the environment.

triethylenetetramine (112-24-3)
Persistence and degradability Not readily biodegradable in water. No (test)data on mobility of the substance available.
Photodegradation in the air. Not established.

alpha-hydro-omega(2-aminomethylethoxy)poly(oxy(methyl-1,2-ethanediyl)ether with 2-ethyl-2-(hydroxymethyl)-1,3-propanediol (3:1)
(39423-51-3)
Persistence and degradability Biodegradability in water: no data available.

Polyamide Curing Agent (MIXTURE)
Persistence and degradability Not established.

Epoxy General Purpose Laminating Hardener
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

05/25/2023 EN (English US) SDS ID: 80LS-22B 8/12

benzyl alcohol (100-51-6)
Persistence and degradability Biodegradable in the soil. Readily biodegradable in water.
Biochemical oxygen demand (BOD)
1.6 g O /g substance
Chemical oxygen demand (COD)
2.4 g O /g substance
ThOD
2.5 g O /g substance

2-piperazin-1-ylethylamine (140-31-8)
Persistence and degradability Not readily biodegradable in water.
Chemical oxygen demand (COD)
0.56 g O /g substance

12.3. Bioaccumulative potential
Epoxy General Purpose Laminating Hardener (Mixture)
Bioaccumulative potential Not established.

triethylenetetramine (112-24-3)
BCF other aquatic organisms 1 3.162 (BCFBAF v3.01, Calculated value)
Log Pow -2.65 (Estimated value, KOWWIN)
Bioaccumulative potential Bioaccumulation: not applicable. Not established.

alpha-hydro-omega(2-aminomethylethoxy)poly(oxy(methyl-1,2-ethanediyl)ether with 2-ethyl-2-(hydroxymethyl)-1,3-propanediol (3:1)
(39423-51-3)
Bioaccumulative potential No bioaccumulation data available.

Polyamide Curing Agent (MIXTURE)
Bioaccumulative potential Not established.

benzyl alcohol (100-51-6)
Log Pow 1 – 1.1 (Experimental value, 20 C)
Bioaccumulative potential Low potential for bioaccumulation (Log Kow < 4). 2-piperazin-1-ylethylamine (140-31-8) BCF fish 1 0.3 - 6.3 (OECD 305: Bioconcentration: Flow-Through Fish Test, 6 week(s), Cyprinus carpio, Flow-through system, Fresh water, Read-across) Log Pow -1.48 (Experimental value, OECD 107: Partition Coefficient (n-octanol/water): Shake Flask Method, 20 C) Bioaccumulative potential Not bioaccumulative. 12.4. Mobility in soil triethylenetetramine (112-24-3) Log Koc 1.885 (log Koc, SRC PCKOCWIN v2.0, Calculated value) Ecology - soil Highly mobile in soil. benzyl alcohol (100-51-6) Surface tension 39 mN/m (20 C) Ecology - soil No (test)data on mobility of the substance available. 2-piperazin-1-ylethylamine (140-31-8) Log Koc 4.57 (log Koc, Read-across, GLP) Ecology - soil Low potential for mobility in soil. 12.5. Other adverse effects Other information : Avoid release to the environment. SECTION 13: Disposal considerations 13.1. Disposal methods Regional legislation (waste) : Disposal must be done according to official regulations. Epoxy General Purpose Laminating Hardener Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 05/25/2023 EN (English US) SDS ID: 80LS-22B 9/12 Waste treatment methods : Dispose of contents/container in accordance with licensed collector s sorting instructions. Sewage disposal recommendations : Do not discharge into drains. Product/Packaging disposal recommendations : Dispose in a safe manner in accordance with local/national regulations. Dispose of contents/container to hazardous or special waste collection point, in accordance with local, regional, national and/or international regulation. Ecology - waste materials : Avoid release to the environment. SECTION 14: Transport information Department of Transportation (DOT) In accordance with DOT Transport document description : UN2735 Polyamines, liquid, corrosive, n.o.s. (trimethylolpropane polyoxy propylene triamine ; triethylenetetramine), 8, II UN-No.(DOT) : UN2735 Proper Shipping Name (DOT) : Polyamines, liquid, corrosive, n.o.s. Class (DOT) : 8 - Class 8 - Corrosive material 49 CFR 173.136 Packing group (DOT) : II - Medium Danger Hazard labels (DOT) : 8 - Corrosive Dangerous for the environment : Yes Marine pollutant : Yes DOT Packaging Non Bulk (49 CFR 173.xxx) : 202 DOT Packaging Bulk (49 CFR 173.xxx) : 242 DOT Special Provisions (49 CFR 172.102) : B2 - MC 300, MC 301, MC 302, MC 303, MC 305, and MC 306 and DOT 406 cargo tanks are not authorized. IB2 - Authorized IBCs: Metal (31A, 31B and 31N); Rigid plastics (31H1 and 31H2); Composite (31HZ1). Additional Requirement: Only liquids with a vapor pressure less than or equal to 110 kPa at 50 C (1.1 bar at 122 F), or 130 kPa at 55 C (1.3 bar at 131 F) are authorized. T11 - 6 178.274(d)(2) Normal............. 178.275(d)(3) TP1 - The maximum degree of filling must not exceed the degree of filling determined by the following: Degree of filling = 97 / 1 + a (tr - tf) Where: tr is the maximum mean bulk temperature during transport, and tf is the temperature in degrees celsius of the liquid during filling. TP27 - A portable tank having a minimum test pressure of 4 bar (400 kPa) may be used provided the calculated test pressure is 4 bar or less based on the MAWP of the hazardous material, as defined in 178.275 of this subchapter, where the test pressure is 1.5 times the MAWP. DOT Packaging Exceptions (49 CFR 173.xxx) : 154 DOT Quantity Limitations Passenger aircraft/rail (49 CFR 173.27) : 1 L DOT Quantity Limitations Cargo aircraft only (49 CFR 175.75) : 30 L DOT Vessel Stowage Location : A - The material may be stowed on deck or under deck on a cargo vessel and on a passenger vessel. DOT Vessel Stowage Other : 52 - Stow separated from acids Emergency Response Guide (ERG) Number : 153 Other information : No supplementary information available. Transportation of Dangerous Goods Not applicable Epoxy General Purpose Laminating Hardener Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 05/25/2023 EN (English US) SDS ID: 80LS-22B 10/12 Transport by sea Transport document description (IMDG) : UN 2735 POLYAMINES, LIQUID, CORROSIVE, N.O .S. (trimethylolpropane polyoxy propylene triamine ; triethylenetetramine), 8, II UN-No. (IMDG) : 2735 Proper Shipping Name (IMDG) : POLYAMINES, LIQUID, CORROSIVE, N.O.S . Class (IMDG) : 8 - Corrosive substances Packing group (IMDG) : II - substances presenting medium danger Marine pollutant : Yes Air transport Transport document description (IATA) : UN 2735 Polyamines, liquid, corrosive, n.o.s. (trimethylolpropane polyoxy propylene triamine , triethylenetetra amine), 8, II UN-No. (IATA) : 2735 Proper Shipping Name (IATA) : Polyamines, liquid, corrosive, n.o.s. Class (IATA) : 8 - Corrosives Packing group (IATA) : II - Medium Danger SECTION 15: Regulatory information 15.1. US Federal regulations Epoxy General Purpose Laminating Hardener (Mixture) SARA Section 311/312 Hazard Classes Delayed (chronic) health hazard triethylenetetramine (112-24-3) Listed on the United States TSCA (Toxic Substances Control Act) inventory alpha-hydro-omega(2-aminomethylethoxy)poly(oxy(methyl-1,2-ethanediyl)ether with 2-ethyl-2-(hydroxymethyl)-1,3-propanediol (3:1) (39423-51-3) Listed on the United States TSCA (Toxic Substances Control Act) inventory EPA TSCA Regulatory Flag XU - XU - indicates a substance exempt from reporting under the Chemical Data Reporting Rule, (40 CFR 711). Polyamide Curing Agent (MIXTURE) Not listed on the United States TSCA (Toxic Substances Control Act) inventory benzyl alcohol (100-51-6) Listed on the United States TSCA (Toxic Substances Control Act) inventory 2-piperazin-1-ylethylamine (140-31-8) Listed on the United States TSCA (Toxic Substances Control Act) inventory 15.2. International regulations CANADA triethylenetetramine (112-24-3) Listed on the Canadian DSL (Domestic Substances List) alpha-hydro-omega(2-aminomethylethoxy)poly(oxy(methyl-1,2-ethanediyl)ether with 2-ethyl-2-(hydroxymethyl)-1,3-propanediol (3:1) (39423-51-3) Listed on the Canadian DSL (Domestic Substances List) Polyamide Curing Agent (MIXTURE) Not listed on the Canadian DSL (Domestic Substances List)/NDSL (Non-Domestic Substances List) benzyl alcohol (100-51-6) Listed on the Canadian DSL (Domestic Substances List) Epoxy General Purpose Laminating Hardener Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 05/25/2023 EN (English US) SDS ID: 80LS-22B 11/12 2-piperazin-1-ylethylamine (140-31-8) Listed on the Canadian DSL (Domestic Substances List) EU-Regulations No additional information available National regulations No additional information available 15.3. US State regulations Component State or local regulations triethylenetetramine(112-24-3) U.S. - New Jersey - Right to Know Hazardous Substance List 2-piperazin-1-ylethylamine(140-31-8) U.S. - New Jersey - Right to Know Hazardous Substance List SECTION 16: Other information according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations Revision date : 05/15/2023 Data sources : REGULATION (EC) No 1272/2008 OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 16 December 2008 on classification, labeling and packaging of substances and mixtures, amending and repealing Directives 67/548/EEC and 1999/45/EC, and amending Regulation (EC) No 1907/2006. Other information : None. Full text of H-phrases: H301 Toxic if swallowed H302 Harmful if swallowed H311 Toxic in contact with skin H312 Harmful in contact with skin H314 Causes severe skin burns and eye damage H315 Causes skin irritation H317 May cause an allergic skin reaction H318 Causes serious eye damage H319 Causes serious eye irritation H332 Harmful if inhaled H335 May cause respiratory irritation H360 May damage fertility or the unborn child H400 Very toxic to aquatic life H402 Harmful to aquatic life H410 Very toxic to aquatic life with long lasting effects H411 Toxic to aquatic life with long lasting effects H412 Harmful to aquatic life with long lasting effects Epoxy General Purpose Laminating Hardener Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 05/25/2023 EN (English US) SDS ID: 80LS-22B 12/12 NFPA health hazard : 2 - Materials that, under emergency conditions, can cause temporary incapacitation or residual injury. NFPA fire hazard : 1 - Materials that must be preheated before ignition can occur. NFPA reactivity : 0 - Material that in themselves are normally stable, even under fire conditions. Hazard Rating Health : 2 Moderate Hazard - Temporary or minor injury may occur Flammability : 1 Slight Hazard - Materials that must be preheated before ignition will occur. Includes liquids, solids and semi solids having a flash point above 200 F. (Class IIIB) Physical : 0 Minimal Hazard - Materials that are normally stable, even under fire conditions, and will NOT react with water, polymerize, decompose, condense, or self-react. Non-Explosives. SDS US (GHS HazCom 2012) To the best of our knowledge this SDS is accurate. The the extent allowed by law, this statement is made in lieu of an other warranties, expressed or implied including but not limited to any implied warranty of merchantability or fitness for a particular purpose and is in lieu of any other obligations or liability on the part of Dura Technoligies, Inc.