EPOXY LAMINATING RESIN
Safety Data Sheet 80LS-19A
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
Date of issue: 07/13/2015 Revision date: 07/13/2015 Version: 1.0
07/13/2015 EN (English) SDS ID: 80LS-19A Page 1
SECTION 1: Identification of the substance/mixture and of the company/undertaking
1.1. Product identifier
Product form : Mixture
Trade name : EPOXY LAMINATING RESIN
CAS No : Mixture
Product code : 80LS-19A
Formula : mixture
Other means of identification : DISTRIBUTED BY REVCHEM COMPOSITES, INC
1.2. Relevant identified uses of the substance or mixture and uses advised against
Use of the substance/mixture : EPOXY LAMINATING RESIN
1.3. Details of the supplier of the safety data sheet
Dura Technologies, Inc.
2720 South Willow Avenue #A
Bloomington, CA 92316
909.877.8477
ChemTrec US: 800.424.9300
ChemTrec Int: +1 70 3527 3887
1.4. Emergency telephone number
Emergency number : ChemTrec US: 800.424.9300 Int: +1 70 3527 3887
CHEMTREC: 1-800-424-9300
SECTION 2: Hazards identification
2.1. Classification of the substance or mixture
GHS-US classification
Skin Irrit. 2 H315
Eye Irrit. 2A H319
Eye Irrit. 2B H320
Skin Sens. 1 H317
STOT SE 3 H335
STOT RE 1 H372
Aquatic Chronic 2 H411
2.2. Label elements
GHS-US labelling
Hazard pictograms (GHS-US) :
GHS07
GHS08
GHS09
Signal word (GHS-US) : Danger
Hazard statements (GHS-US) : H315 – Causes skin irritation
H317 – May cause an allergic skin reaction
H319 – Causes serious eye irritation
H320 – Causes eye irritation
H335 – May cause respiratory irritation
H372 – Causes damage to organs through prolonged or repeated exposure
H411 – Toxic to aquatic life with long lasting effects
Precautionary statements (GHS-US) : P260 – Do not breathe dust/fume/gas/mist/vapours/spray
P261 – Avoid breathing dust/fume/gas/mist/vapours/spray
P264 – Wash … thoroughly after handling
P270 – Do not eat, drink or smoke when using this product
P271 – Use only outdoors or in a well-ventilated area
P272 – Contaminated work clothing should not be allowed out of the workplace
P273 – Avoid release to the environment
P280 – Wear protective gloves/protective clothing/eye protection/face protection
EPOXY LAMINATING RESIN
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
07/13/2015 EN (English) SDS ID: 80LS-19A 2/8
P302+P352 – IF ON SKIN: Wash with plenty of soap and water
P304+P340 – IF INHALED: remove victim to fresh air and keep at rest in a position comfortable
for breathing
P305+P351+P338 – If in eyes: Rinse cautiously with water for several minutes. Remove contact
lenses, if present and easy to do. Continue rinsing
P312 – Call a POISON CENTER or doctor/physician if you feel unwell
P314 – Get medical advice and attention if you feel unwell
P321 – Specific treatment (see … on this label)
P332+P313 – If skin irritation occurs: Get medical advice/attention
P333+P313 – If skin irritation or rash occurs: Get medical advice/attention
P337+P313 – If eye irritation persists: Get medical advice/attention
P362 – Take off contaminated clothing and wash before reuse
P362+P364 – Take off contaminated clothing and wash it before reuse
P391 – Collect spillage
P403+P233 – Store in a well-ventilated place. Keep container tightly closed
P405 – Store locked up
P501 – Dispose of contents/container to an approved waste disposal plant.
2.3. Other hazards
No additional information available
2.4. Unknown acute toxicity (GHS-US)
No data available
SECTION 3: Composition/information on ingredients
3.1. Substance
Not applicable
Full text of H-phrases: see section 16
3.2. Mixture
Name Product identifier % GHS-US classification
epoxy resins,liquids, MM<=700 (CAS No) 25068-38-6 <= 80 Not classified
butanedioldiglycidyl ether (CAS No) 2425-79-8 < 15 Acute Tox. 4 (Dermal), H312
Skin Irrit. 2, H315
Eye Irrit. 2A, H319
Skin Sens. 1, H317
trimethylolpropane triacrylate,stabilized (CAS No) 15625-89-5 <= 10 Not classified
poly(propylene glycol) diglycidyl ether, average MW=380 (CAS No) 26142-30-3 < 6 Not classified
SECTION 4: First aid measures
4.1. Description of first aid measures
First-aid measures general : Never give anything by mouth to an unconscious person. If you feel unwell, seek medical advice
(show the label where possible).
First-aid measures after inhalation : Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a
POISON CENTER or doctor/physician if you feel unwell.
First-aid measures after skin contact : Wash with plenty of soap and water. Wash contaminated clothing before reuse. If skin irritation
occurs: Get medical advice/attention. Specific treatment (see ... on this label). If skin irritation or
rash occurs:
First-aid measures after eye contact : Rinse cautiously with water for several minutes. IF IN EYES: Rinse cautiously with water for
several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Remove
contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical
advice/attention.
First-aid measures after ingestion : Rinse mouth. Do NOT induce vomiting. Obtain emergency medical attention.
4.2. Most important symptoms and effects, both acute and delayed
Symptoms/injuries : Causes damage to organs through prolonged or repeated exposure.
Symptoms/injuries after inhalation : May cause an allergic skin reaction. May cause respiratory irritation.
Symptoms/injuries after skin contact : Causes skin irritation.
Symptoms/injuries after eye contact : Causes eye irritation. Causes serious eye irritation.
4.3. Indication of any immediate medical attention and special treatment needed
Until victim can be cared for by specialized staff:
SECTION 5: Firefighting measures
5.1. Extinguishing media
Suitable extinguishing media : Foam. Dry powder. Carbon dioxide. Water spray. Sand.
EPOXY LAMINATING RESIN
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
07/13/2015 EN (English) SDS ID: 80LS-19A 3/8
Unsuitable extinguishing media : Do not use a heavy water stream.
5.2. Special hazards arising from the substance or mixture
Fire hazard : Heating increases the fire hazard. Heating may cause a fire. Heating may cause a fire or
explosion. Insufficient data available on direct fire hazard (flashpoint > 100 C). Self-heating in
large quantities; may catch fire. Temperature above flashpoint: higher fire/explosion hazard.
5.3. Advice for firefighters
Firefighting instructions : Use water spray or fog for cooling exposed containers. Exercise caution when fighting any
chemical fire. Prevent fire-fighting water from entering environment.
Protection during firefighting : Do not enter fire area without proper protective equipment, including respiratory protection.
SECTION 6: Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
6.1.1. For non-emergency personnel
Emergency procedures : Evacuate unnecessary personnel.
6.1.2. For emergency responders
Protective equipment : Equip cleanup crew with proper protection.
Emergency procedures : Ventilate area.
6.2. Environmental precautions
Prevent entry to sewers and public waters. Notify authorities if liquid enters sewers or public waters. Avoid release to the environment.
6.3. Methods and material for containment and cleaning up
For containment : Dam up the liquid spill.
Methods for cleaning up : Soak up spills with inert solids, such as clay or diatomaceous earth as soon as possible. Collect
spillage. Store away from other materials.
6.4. Reference to other sections
See Heading 8. Exposure controls and personal protection.
SECTION 7: Handling and storage
7.1. Precautions for safe handling
Precautions for safe handling : Wash hands and other exposed areas with mild soap and water before eating, drinking or
smoking and when leaving work. Provide good ventilation in process area to prevent formation of
vapour. Avoid breathing dust/fume/gas/mist/vapours/spray. Use only outdoors or in a well-
ventilated area. Do not breathe dust/fume/gas/mist/vapours/spray.
Hygiene measures : Wash hands and other exposed areas with mild soap and water before eat, drink or smoke and
when leaving work. Wash … thoroughly after handling. Contaminated work clothing should not be
allowed out of the workplace. Wash contaminated clothing before reuse. Do not eat, drink or
smoke when using this product.
7.2. Conditions for safe storage, including any incompatibilities
Storage conditions : Keep only in the original container in a cool, well ventilated place away from : Keep container
tightly closed.
Incompatible products : Strong bases. Strong acids.
Incompatible materials : Sources of ignition. Direct sunlight.
Storage temperature : 2 – 40 C
7.3. Specific end use(s)
No additional information available
SECTION 8: Exposure controls/personal protection
8.1. Control parameters
No additional information available
8.2. Exposure controls
Personal protective equipment : Avoid all unnecessary exposure.
Materials for protective clothing : GIVE GOOD RESISTANCE: rubber.
Hand protection : Wear protective gloves.
Eye protection : Chemical goggles or safety glasses.
Skin and body protection : Wear suitable protective clothing.
EPOXY LAMINATING RESIN
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
07/13/2015 EN (English) SDS ID: 80LS-19A 4/8
Respiratory protection : Wear appropriate mask.
Other information : Do not eat, drink or smoke during use.
SECTION 9: Physical and chemical properties
9.1. Information on basic physical and chemical properties
Physical state : Liquid
Appearance : Liquid.
Colour : Colourless.
Odour : slight. characteristic.
Odour threshold : No data available
pH : No data available
Relative evaporation rate (butylacetate=1) : No data available
Relative evaporation rate (ether=1) : < 1 slower than ether Melting point : N/A Freezing point : No data available Boiling point : > 200 C
Flash point : > 100 C
Auto-ignition temperature : No data available
Decomposition temperature : No data available
Flammability (solid, gas) : No data available
Vapour pressure : < 2 mm Hg
Relative vapour density at 20 C : No data available
Relative density : No data available
Density : 1.13 g/l
Solubility : Insoluble in water.
Log Pow : No data available
Log Kow : No data available
Viscosity, kinematic : No data available
Viscosity, dynamic : No data available
Explosive properties : No data available
Oxidising properties : No data available
Explosive limits : No data available
9.2. Other information
No additional information available
SECTION 10: Stability and reactivity
10.1. Reactivity
No additional information available
10.2. Chemical stability
Combustible liquid. Not established.
10.3. Possibility of hazardous reactions
Not established.
10.4. Conditions to avoid
Open flame. Direct sunlight. Extremely high or low temperatures.
10.5. Incompatible materials
Strong acids. Strong bases.
10.6. Hazardous decomposition products
fume. Carbon monoxide. Carbon dioxide.
SECTION 11: Toxicological information
11.1. Information on toxicological effects
EPOXY LAMINATING RESIN
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
07/13/2015 EN (English) SDS ID: 80LS-19A 5/8
Acute toxicity : Not classified
(Lack of data)
trimethylolpropane triacrylate,stabilized (15625-89-5)
LD50 oral rat 5190 mg/kg (Rat)
LD50 dermal rabbit 5170 mg/kg (Rabbit)
ATE CLP (oral) 5190.000 mg/kg bodyweight
ATE CLP (dermal) 5170.000 mg/kg bodyweight
epoxy resins,liquids, MM<=700 (25068-38-6)
LD50 oral rat > 2000 mg/kg (Rat)
LD50 dermal rabbit > 2000 mg/kg (Rabbit)
butanedioldiglycidyl ether (2425-79-8)
LD50 oral rat 2980 mg/kg (Rat)
LD50 dermal rabbit 1130 mg/kg (Rabbit)
ATE CLP (oral) 2980.000 mg/kg bodyweight
ATE CLP (dermal) 1130.000 mg/kg bodyweight
ATE CLP (dust,mist) 1.500 mg/l/4h
Skin corrosion/irritation : Causes skin irritation.
Serious eye damage/irritation : Causes serious eye irritation. Causes eye irritation.
Respiratory or skin sensitisation : May cause an allergic skin reaction.
Germ cell mutagenicity : Not classified
Based on available data, the classification criteria are not met
Carcinogenicity : Not classified
Reproductive toxicity : Not classified
Based on available data, the classification criteria are not met
Specific target organ toxicity (single exposure) : May cause respiratory irritation.
Specific target organ toxicity (repeated
exposure)
: Causes damage to organs through prolonged or repeated exposure.
Based on available data, the classification criteria are not met
Causes damage to organs through prolonged or repeated exposure
Aspiration hazard : Not classified
Based on available data, the classification criteria are not met
Potential adverse human health effects and
symptoms
: Based on available data, the classification criteria are not met.
Symptoms/injuries after inhalation : May cause an allergic skin reaction. May cause respiratory irritation.
Symptoms/injuries after skin contact : Causes skin irritation.
Symptoms/injuries after eye contact : Causes eye irritation. Causes serious eye irritation.
Likely routes of exposure : Inhalation
SECTION 12: Ecological information
12.1. Toxicity
Ecology – water : Toxic to aquatic life with long lasting effects.
trimethylolpropane triacrylate,stabilized (15625-89-5)
LC50 fish 1 28.6 mg/l (Salmo gairdneri (Oncorhynchus mykiss); Stabilizer)
EC50 Daphnia 1 19 mg/l (24 h; Daphnia magna; Stabilizer)
LC50 fish 2 33 mg/l (Leuciscus idus; Stabilizer)
epoxy resins,liquids, MM<=700 (25068-38-6)
LC50 fish 1 1 - 10 mg/l (Salmo gairdneri / Oncorhynchus mykiss)
EC50 Daphnia 1 1 - 10 mg/l (Invertebrata)
EC50 other aquatic organisms 1 > 100 mg/l (Activated sludge; Estimated value)
EC50 Daphnia 2 2.7 mg/l (Daphnia magna)
butanedioldiglycidyl ether (2425-79-8)
LC50 fish 1 202393 mg/l (96 h; Pisces)
EPOXY LAMINATING RESIN
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
07/13/2015 EN (English) SDS ID: 80LS-19A 6/8
butanedioldiglycidyl ether (2425-79-8)
Threshold limit algae 1 88930 mg/l (96 h; Algae)
12.2. Persistence and degradability
EPOXY LAMINATING RESIN (Mixture)
Persistence and degradability May cause long-term adverse effects in the environment.
trimethylolpropane triacrylate,stabilized (15625-89-5)
Persistence and degradability Biodegradability in water: no data available.
ThOD 1.835 g O /g substance
epoxy resins,liquids, MM<=700 (25068-38-6)
Persistence and degradability Not readily biodegradable in water.
butanedioldiglycidyl ether (2425-79-8)
Persistence and degradability Not readily biodegradable in water.
poly(propylene glycol) diglycidyl ether, average MW=380 (26142-30-3)
Persistence and degradability Biodegradability in water: no data available.
12.3. Bioaccumulative potential
EPOXY LAMINATING RESIN (Mixture)
Bioaccumulative potential Not established.
trimethylolpropane triacrylate,stabilized (15625-89-5)
Bioaccumulative potential No bioaccumulation data available.
epoxy resins,liquids, MM<=700 (25068-38-6)
Log Pow > 3
Bioaccumulative potential According to literature: bioaccumulative.
butanedioldiglycidyl ether (2425-79-8)
Log Pow -0.15
Bioaccumulative potential Bioaccumulation: not applicable.
poly(propylene glycol) diglycidyl ether, average MW=380 (26142-30-3)
Bioaccumulative potential No bioaccumulation data available.
12.4. Mobility in soil
No additional information available
12.5. Other adverse effects
Other information : Avoid release to the environment.
SECTION 13: Disposal considerations
13.1. Waste treatment methods
Waste disposal recommendations : Dispose in a safe manner in accordance with local/national regulations. Dispose of
contents/container to an approved waste disposal plant.
Ecology – waste materials : Avoid release to the environment.
SECTION 14: Transport information
In accordance with DOT
Not regulated for transport
Additional information
Other information : No supplementary information available.
ADR
Transport document description :
Transport by sea
UN-No.( IMDG) : 3082
Proper Shipping Name (IMDG) : Environmently Hazarous substance (AQUATIC ENVIRONMENT), Liquid,N.O.S.(Epoxy Resin)
EPOXY LAMINATING RESIN
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
07/13/2015 EN (English) SDS ID: 80LS-19A 7/8
Hazard Classes (IMDG) : 9
Packing group (IMDG) : III – Minor Danger
Air transport
UN-No.(IATA) : 3082
Proper Shipping Name (IATA) : Environmently Hazarous substance (AQUATIC ENVIRONMENT), Liquid,N.O.S.(Epoxy Resin)
Hazard Classes (IATA) : 9
Packing group (IATA) : III – Minor Danger
SECTION 15: Regulatory information
15.1. US Federal regulations
No additional information available
15.2. International regulations
CANADA
No additional information available
EU-Regulations
No additional information available
Classification according to Regulation (EC) No. 1272/2008 [CLP]
Skin Irrit. 2 H315
Eye Irrit. 2 H319
Skin Sens. 1 H317
Aquatic Chronic 2 H411
Full text of H-phrases: see section 16
Classification according to Directive 67/548/EEC [DSD] or 1999/45/EC [DPD]
Xi; R36/38
R43
N; R51/53
Full text of R-phrases: see section 16
15.2.2. National regulations
No additional information available
15.3. US State regulations
No additional information available
SECTION 16: Other information
Other information : None.
Full text of H-phrases: see section 16:
—— Acute Tox. 4 (Dermal) Acute toxicity (dermal), Category 4
—— Aquatic Chronic 2 Hazardous to the aquatic environment Chronic Hazard, Category
2
—— Eye Irrit. 2A Serious eye damage/eye irritation, Category 2A
—— Eye Irrit. 2B Serious eye damage/eye irritation, Category 2B
—— Skin Irrit. 2 Skin corrosion/irritation, Category 2
—— Skin Sens. 1 Sensitisation Skin, category 1
EPOXY LAMINATING RESIN
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
07/13/2015 EN (English) SDS ID: 80LS-19A 8/8
—— STOT RE 1 Specific target organ toxicity Repeated exposure, Category 1
—— STOT SE 3 Specific target organ toxicity Single exposure, Category 3,
Respiratory tract irritation
—— H312 Harmful in contact with skin
—— H315 Causes skin irritation
—— H317 May cause an allergic skin reaction
—— H319 Causes serious eye irritation
—— H320 Causes eye irritation
—— H335 May cause respiratory irritation
—— H372 Causes damage to organs through prolonged or repeated exposure
—— H411 Toxic to aquatic life with long lasting effects
NFPA health hazard : 1 – Exposure could cause irritation but only minor residual
injury even if no treatment is given.
NFPA fire hazard : 1 – Must be preheated before ignition can occur.
NFPA reactivity : 1 – Normally stable, but can become unstable at elevated
temperatures and pressures or may react with water with
some release of energy, but not violently.
HMIS III Rating
Health : 1 Slight Hazard – Irritation or minor reversible injury possible
Flammability : 1 Slight Hazard
Physical : 1 Slight Hazard
Personal Protection : H
SDS US (GHS HazCom 2012)
To the best of our knowledge this SDS is accurate. The the extent allowed by law, this statement is made in lieu of an other warranties, expressed or implied including but not limited to any implied
warranty of merchantability or fitness for a particular purpose and is in lieu of any other obligations or liability on the part of Dura Technoligies, Inc.