37BO104B_SDS.pdf

FEATHER-RITE QUALITY LIGHTWEIGHT AUTOBODY FILLER
Not available.
Liquid.
(888) 345-5732
SAFETY DATA SHEET
Product name
Other means of
identification
Product type
Emergency telephone
number of the company
Section 1. Identification
:
:
:
:
Manufacturer :U.S. CHEMICAL & PLASTICS
600 Nova Dr. S.E.
Massillon, OH 44646
USA
Relevant identified uses of the substance or mixture and uses advised against
Paint or paint related material.
21330
21330Product code :
Product Information
Telephone Number
:(330) 830-6000
Regulatory Information
Telephone Number
:(216) 566-2902
Transportation Emergency
Telephone Number
:(800) 424-9300
Section 2. Hazards identification
FLAMMABLE LIQUIDS – Category 3
ACUTE TOXICITY (inhalation) – Category 4
SKIN CORROSION/IRRITATION – Category 2
SERIOUS EYE DAMAGE/ EYE IRRITATION – Category 2A
CARCINOGENICITY – Category 1B
TOXIC TO REPRODUCTION – Category 2
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) – Category 1
ASPIRATION HAZARD – Category 1
Classification of the
substance or mixture
:
Signal word :Danger
Hazard pictograms :
GHS label elements
Percentage of the mixture consisting of ingredient(s) of unknown acute dermal toxicity:
17%
OSHA/HCS status :This material is considered hazardous by the OSHA Hazard Communication Standard
(29 CFR 1910.1200).
Date of issue/Date of revision :11/29/2022Date of previous issue :6/20/2022 Version:8 1/15
21330 FEATHER-RITE QUALITY LIGHTWEIGHT AUTOBODY
FILLER
SHW-85-NA-GHS-US

Section 2. Hazards identification
Precautionary statements
Prevention :Obtain special instructions before use. Do not handle until all safety precautions have
been read and understood. Wear protective gloves, protective clothing and eye or face
protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition
sources. No smoking. Use explosion-proof electrical, ventilating or lighting equipment.
Use non-sparking tools. Take action to prevent static discharges. Keep container
tightly closed. Use only outdoors or in a well-ventilated area. Do not breathe vapor. Do
not eat, drink or smoke when using this product. Wash thoroughly after handling.
Response :IF exposed or concerned: Get medical advice or attention. IF INHALED: Remove
person to fresh air and keep comfortable for breathing. Call a POISON CENTER or
doctor if you feel unwell. IF SWALLOWED: Immediately call a POISON CENTER or
doctor. Do NOT induce vomiting. IF ON SKIN (or hair): Take off immediately all
contaminated clothing. Rinse skin with water. IF ON SKIN: Wash with plenty of water.
If skin irritation occurs: Get medical advice or attention. IF IN EYES: Rinse cautiously
with water for several minutes. Remove contact lenses, if present and easy to do.
Continue rinsing. If eye irritation persists: Get medical advice or attention.
Storage :Store locked up. Store in a well-ventilated place. Keep cool.
Disposal Dispose of contents and container in accordance with all local, regional, national and
international regulations.
Hazards not otherwise
classified
:None known.
Flammable liquid and vapor.
May be fatal if swallowed and enters airways.
Causes skin irritation.
Causes serious eye irritation.
Harmful if inhaled.
May cause cancer.
Suspected of damaging fertility or the unborn child.
Causes damage to organs through prolonged or repeated exposure. (hearing organs,
lungs)
:Hazard statements
Please refer to the SDS for additional information. Keep out of reach of children. Do not
transfer contents to other containers for storage.
Supplemental label
elements
DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. Contains solvents which
can cause permanent brain and nervous system damage. Intentional misuse by
deliberately concentrating and inhaling the contents can be harmful or fatal. WARNING:
This product contains chemicals known to the State of California to cause cancer and
birth defects or other reproductive harm. FOR PROFESSIONAL USE ONLY. This
product must be mixed with other components before use. Before opening the
packages, READ AND FOLLOW WARNING LABELS ON ALL COMPONENTS.
:
Section 3. Composition/information on ingredients
Calcium Carbonate 25 – 50 471-34-1
Styrene 10 – <20 100-42-5 Talc 10 14807-96-6 Silica gel, pptd., cryst.-free 3 112926-00-8 Titanium Dioxide 0.3 13463-67-7 Ingredient name CAS number% by weight Other means of identification :Not available. Substance/mixture CAS number/other identifiers :Mixture Any concentration shown as a range is to protect confidentiality or is due to batch variation. Date of issue/Date of revision :11/29/2022Date of previous issue :6/20/2022 Version:8 2/15 21330 FEATHER-RITE QUALITY LIGHTWEIGHT AUTOBODY FILLER SHW-85-NA-GHS-US Section 3. Composition/information on ingredients Occupational exposure limits, if available, are listed in Section 8. There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified and hence require reporting in this section. Get medical attention immediately. Call a poison center or physician. Wash out mouth with water. Remove dentures if any. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Stop if the exposed person feels sick as vomiting may be dangerous. Aspiration hazard if swallowed. Can enter lungs and cause damage. Do not induce vomiting. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Never give anything by mouth to an unconscious person. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband. Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10 minutes. Get medical attention. Flush contaminated skin with plenty of water. Remove contaminated clothing and shoes. Wash contaminated clothing thoroughly with water before removing it, or wear gloves. Continue to rinse for at least 10 minutes. Get medical attention. Wash clothing before reuse. Clean shoes thoroughly before reuse. Remove victim to fresh air and keep at rest in a position comfortable for breathing. If it is suspected that fumes are still present, the rescuer should wear an appropriate mask or self-contained breathing apparatus. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Get medical attention. If necessary, call a poison center or physician. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband. Section 4. First aid measures Eye contact Skin contact Inhalation Ingestion : : : : Description of necessary first aid measures Most important symptoms/effects, acute and delayed Inhalation :Harmful if inhaled. May be fatal if swallowed and enters airways.:Ingestion Skin contact :Causes skin irritation. Causes serious eye irritation.:Eye contact Over-exposure signs/symptoms Skin contact Inhalation Adverse symptoms may include the following: reduced fetal weight increase in fetal deaths skeletal malformations Adverse symptoms may include the following: irritation redness reduced fetal weight increase in fetal deaths skeletal malformations : : Eye contact :Adverse symptoms may include the following: pain or irritation watering redness Potential acute health effects Date of issue/Date of revision :11/29/2022Date of previous issue :6/20/2022 Version:8 3/15 21330 FEATHER-RITE QUALITY LIGHTWEIGHT AUTOBODY FILLER SHW-85-NA-GHS-US Section 4. First aid measures Protection of first-aiders:No action shall be taken involving any personal risk or without suitable training. If it is suspected that fumes are still present, the rescuer should wear an appropriate mask or self-contained breathing apparatus. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Wash contaminated clothing thoroughly with water before removing it, or wear gloves. Notes to physician :Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled. Specific treatments :No specific treatment. Ingestion Adverse symptoms may include the following: nausea or vomiting reduced fetal weight increase in fetal deaths skeletal malformations : See toxicological information (Section 11) Indication of immediate medical attention and special treatment needed, if necessary Section 5. Fire-fighting measures Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training. Move containers from fire area if this can be done without risk. Use water spray to keep fire-exposed containers cool. Hazardous thermal decomposition products Specific hazards arising from the chemical Decomposition products may include the following materials: carbon dioxide carbon monoxide metal oxide/oxides Flammable liquid and vapor. Runoff to sewer may create fire or explosion hazard. In a fire or if heated, a pressure increase will occur and the container may burst, with the risk of a subsequent explosion. The vapor/gas is heavier than air and will spread along the ground. Vapors may accumulate in low or confined areas or travel a considerable distance to a source of ignition and flash back. Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode. Special protective equipment for fire-fighters Use dry chemical, CO , water spray (fog) or foam. Extinguishing media : : : Flammable liquid.Remark : Do not use water jet. Suitable extinguishing media : Unsuitable extinguishing media : Special protective actions for fire-fighters : Section 6. Accidental release measures Personal precautions, protective equipment and emergency procedures :No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Shut off all ignition sources. No flares, smoking or flames in hazard area. Avoid breathing vapor or mist. Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment. For non-emergency personnel Date of issue/Date of revision :11/29/2022Date of previous issue :6/20/2022 Version:8 4/15 21330 FEATHER-RITE QUALITY LIGHTWEIGHT AUTOBODY FILLER SHW-85-NA-GHS-US Section 6. Accidental release measures Environmental precautions Stop leak if without risk. Move containers from spill area. Use spark-proof tools and explosion-proof equipment. Approach release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local regulations (see Section 13). Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled product. Note: see Section 1 for emergency contact information and Section 13 for waste disposal. :Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air). Large spill : Stop leak if without risk. Move containers from spill area. Use spark-proof tools and explosion-proof equipment. Dilute with water and mop up if water-soluble. Alternatively, or if water-insoluble, absorb with an inert dry material and place in an appropriate waste disposal container. Dispose of via a licensed waste disposal contractor. Small spill : Methods and materials for containment and cleaning up For emergency responders:If specialized clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials. See also the information in "For non- emergency personnel". Section 7. Handling and storage Advice on general occupational hygiene Conditions for safe storage, including any incompatibilities Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. See also Section 8 for additional information on hygiene measures. Store in accordance with local regulations. Store in a segregated and approved area. Store in original container protected from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Store locked up. Eliminate all ignition sources. Separate from oxidizing materials. Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate containment to avoid environmental contamination. See Section 10 for incompatible materials before handling or use. : : Protective measures Put on appropriate personal protective equipment (see Section 8). Avoid exposure - obtain special instructions before use. Avoid exposure during pregnancy. Do not handle until all safety precautions have been read and understood. Do not get in eyes or on skin or clothing. Do not breathe vapor or mist. Do not swallow. Use only with adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Do not enter storage areas and confined spaces unless adequately ventilated. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when not in use. Store and use away from heat, sparks, open flame or any other ignition source. Use explosion-proof electrical (ventilating, lighting and material handling) equipment. Use only non-sparking tools. Take precautionary measures against electrostatic discharges. Empty containers retain product residue and can be hazardous. Do not reuse container. : Precautions for safe handling Date of issue/Date of revision :11/29/2022Date of previous issue :6/20/2022 Version:8 5/15 21330 FEATHER-RITE QUALITY LIGHTWEIGHT AUTOBODY FILLER SHW-85-NA-GHS-US Calcium Carbonate 471-34-1 NIOSH REL (United States, 10/2020). [calcium carbonate] TWA: 5 mg/m 10 hours. Form: Respirable fraction TWA: 10 mg/m 10 hours. Form: Total Styrene 100-42-5 ACGIH TLV (United States, 1/2022). Ototoxicant. TWA: 10 ppm 8 hours. STEL: 20 ppm 15 minutes. OSHA PEL Z2 (United States, 2/2013). TWA: 100 ppm 8 hours. CEIL: 200 ppm AMP: 600 ppm 5 minutes. NIOSH REL (United States, 10/2020). TWA: 50 ppm 10 hours. TWA: 215 mg/m 10 hours. STEL: 100 ppm 15 minutes. STEL: 425 mg/m 15 minutes. Talc 14807-96-6 NIOSH REL (United States, 10/2020). TWA: 2 mg/m 10 hours. Form: Respirable fraction ACGIH TLV (United States, 1/2022). TWA: 2 mg/m 8 hours. Form: Respirable fraction Silica gel, pptd., cryst.-free 112926-00-8 NIOSH REL (United States, 10/2020). [SILICA, AMORPHOUS] TWA: 6 mg/m 10 hours. Titanium Dioxide 13463-67-7 OSHA PEL (United States, 5/2018). TWA: 15 mg/m 8 hours. Form: Total dust ACGIH TLV (United States, 1/2022). TWA: 2.5 mg/m 8 hours. Form: respirable fraction, finescale particles Section 8. Exposure controls/personal protection Ingredient name Exposure limits Control parameters Occupational exposure limits (OSHA United States) Vinyl benzene 100-42-5 CA Alberta Provincial (Canada, 6/2018). 15 min OEL: 40 ppm 15 minutes. 15 min OEL: 170 mg/m 15 minutes. 8 hrs OEL: 85 mg/m 8 hours. 8 hrs OEL: 20 ppm 8 hours. CA British Columbia Provincial (Canada, 3/2022). TWA: 20 ppm 8 hours. STEL: 40 ppm 15 minutes. CA Ontario Provincial (Canada, 6/2019). TWA: 35 ppm 8 hours. STEL: 100 ppm 15 minutes. CA Quebec Provincial (Canada, 6/2021). Absorbed through skin. TWAEV: 50 ppm 8 hours. TWAEV: 213 mg/m 8 hours. STEV: 100 ppm 15 minutes. Ingredient name Exposure limits Occupational exposure limits (Canada) CAS # CAS # Date of issue/Date of revision :11/29/2022Date of previous issue :6/20/2022 Version:8 6/15 21330 FEATHER-RITE QUALITY LIGHTWEIGHT AUTOBODY FILLER SHW-85-NA-GHS-US Section 8. Exposure controls/personal protection Appropriate engineering controls :Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or other engineering controls to keep worker exposure to airborne contaminants below any recommended or statutory limits. The engineering controls also need to keep gas, vapor or dust concentrations below any lower explosive limits. Use explosion-proof ventilation equipment. STEV: 426 mg/m 15 minutes. CA Saskatchewan Provincial (Canada, 7/2013). STEL: 40 ppm 15 minutes. TWA: 20 ppm 8 hours. talc (none asbestiform) 14807-96-6 CA British Columbia Provincial (Canada, 3/2022). TWA: 2 mg/m 8 hours. Form: Respirable CA Quebec Provincial (Canada, 6/2021). TWAEV: 2 mg/m 8 hours. Form: Respirable dust. CA Alberta Provincial (Canada, 6/2018). 8 hrs OEL: 2 mg/m 8 hours. Form: Respirable particulate CA Ontario Provincial (Canada, 6/2019). TWA: 2 mg/m 8 hours. Form: Respirable particulate matter. TWA: 2 f/cc 8 hours. CA Saskatchewan Provincial (Canada, 7/2013). TWA: 2 mg/m 8 hours. Form: respirable fraction Titanium dioxide 13463-67-7 CA British Columbia Provincial (Canada, 3/2022). TWA: 10 mg/m 8 hours. Form: Total dust TWA: 3 mg/m 8 hours. Form: respirable fraction CA Quebec Provincial (Canada, 6/2021). TWAEV: 10 mg/m 8 hours. Form: Total dust. CA Alberta Provincial (Canada, 6/2018). 8 hrs OEL: 10 mg/m 8 hours. CA Ontario Provincial (Canada, 6/2019). TWA: 10 mg/m 8 hours. CA Saskatchewan Provincial (Canada, 7/2013). STEL: 20 mg/m 15 minutes. TWA: 10 mg/m 8 hours. Styrene 100-42-5 NOM-010-STPS-2014 (Mexico, 4/2016). TWA: 20 ppm 8 hours. STEL: 40 ppm 15 minutes. N,N-dimethylaniline 121-69-7 NOM-010-STPS-2014 (Mexico, 4/2016). Absorbed through skin. TWA: 5 ppm 8 hours. STEL: 10 ppm 15 minutes. Exposure limits Occupational exposure limits (Mexico) CAS # Date of issue/Date of revision :11/29/2022Date of previous issue :6/20/2022 Version:8 7/15 21330 FEATHER-RITE QUALITY LIGHTWEIGHT AUTOBODY FILLER SHW-85-NA-GHS-US Section 8. Exposure controls/personal protection Hand protection Based on the hazard and potential for exposure, select a respirator that meets the appropriate standard or certification. Respirators must be used according to a respiratory protection program to ensure proper fitting, training, and other important aspects of use. Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. Considering the parameters specified by the glove manufacturer, check during use that the gloves are still retaining their protective properties. It should be noted that the time to breakthrough for any glove material may be different for different glove manufacturers. In the case of mixtures, consisting of several substances, the protection time of the gloves cannot be accurately estimated. Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists, gases or dusts. If contact is possible, the following protection should be worn, unless the assessment indicates a higher degree of protection: chemical splash goggles. Eye/face protection Respiratory protection : : : Body protection Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. When there is a risk of ignition from static electricity, wear anti- static protective clothing. For the greatest protection from static discharges, clothing should include anti-static overalls, boots and gloves. : Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation. In some cases, fume scrubbers, filters or engineering modifications to the process equipment will be necessary to reduce emissions to acceptable levels. Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Wash contaminated clothing before reusing. Ensure that eyewash stations and safety showers are close to the workstation location. Hygiene measures : Individual protection measures Skin protection Other skin protection :Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. Environmental exposure controls : Section 9. Physical and chemical properties Physical state Melting point/freezing point Liquid. Not available. Not available.Odor pH Not available.Color Evaporation rate 0.49 (butyl acetate = 1) Flash point Closed cup: 41 C (105.8 F) [Pensky-Martens Closed Cup] Not applicable. Not available.Odor threshold : : : : : : : : Appearance :145 C (293 F) :Flammable liquid. :Lower: 1.1% Upper: 6.1% Boiling point, initial boiling point, and boiling range Flammability Lower and upper explosion limit/flammability limit The conditions of measurement of all properties are at standard temperature and pressure unless otherwise indicated. Date of issue/Date of revision :11/29/2022Date of previous issue :6/20/2022 Version:8 8/15 21330 FEATHER-RITE QUALITY LIGHTWEIGHT AUTOBODY FILLER SHW-85-NA-GHS-US Section 9. Physical and chemical properties Vapor pressure Relative density 1 3.6 [Air = 1] Auto-ignition temperature Not available. Not applicable. Viscosity Kinematic (40 C (104 F)): <20.5 mm 2 /s (<20.5 cSt) Partition coefficient: n- octanol/water : : : : : : Decomposition temperature:Not available. Heat of combustion :7.756 kJ/g Aerosol product Molecular weight :Not applicable. Relative vapor density 0.57 kPa (4.3 mm Hg) Solubility(ies) : Media Result cold water Not soluble Section 10. Stability and reactivity Hazardous decomposition products Conditions to avoid Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld, braze, solder, drill, grind or expose containers to heat or sources of ignition. Do not allow vapor to accumulate in low or confined areas. Under normal conditions of storage and use, hazardous decomposition products should not be produced. The product is stable.Chemical stability Reactive or incompatible with the following materials: oxidizing materials : : : Incompatible materials : Possibility of hazardous reactions :Under normal conditions of storage and use, hazardous reactions will not occur. Reactivity :No specific test data related to reactivity available for this product or its ingredients. Section 11. Toxicological information Acute toxicity Calcium Carbonate LD50 Oral Rat 6450 mg/kg - Styrene LC50 Inhalation Gas. Rat 2770 ppm 4 hours LC50 Inhalation Vapor Rat 11800 mg/m 4 hours LD50 Oral Rat 2650 mg/kg - Product/ingredient name Result Species Dose Exposure Irritation/Corrosion Information on toxicological effects Date of issue/Date of revision :11/29/2022Date of previous issue :6/20/2022 Version:8 9/15 21330 FEATHER-RITE QUALITY LIGHTWEIGHT AUTOBODY FILLER SHW-85-NA-GHS-US Section 11. Toxicological information Carcinogenicity Not available. Mutagenicity Not available. Teratogenicity Not available. Reproductive toxicity Not available. Calcium Carbonate Eyes - Severe irritantRabbit - 24 hours 750 ug - Skin - Moderate irritantRabbit - 24 hours 500 mg - Styrene Eyes - Mild irritant Human - 50 ppm - Eyes - Moderate irritantRabbit - 24 hours 100 mg - Eyes - Severe irritantRabbit - 100 mg - Skin - Mild irritant Rabbit - 500 mg - Skin - Moderate irritantRabbit - 100 % - Talc Skin - Mild irritant Human - 72 hours 300 ug I - Titanium Dioxide Skin - Mild irritant Human - 72 hours 300 ug I - Product/ingredient name Result Score Exposure Observation Sensitization Not available. Species Specific target organ toxicity (single exposure) Specific target organ toxicity (repeated exposure) Styrene Category 3 - Respiratory tract irritation Category 3 Narcotic effects Name Category Name Category Styrene Category 1 - hearing organs Talc Category 1 inhalation lungs Aspiration hazard Name Result Styrene ASPIRATION HAZARD - Category 1 Route of exposure Target organs Route of exposure Target organs Classification Styrene - 2A Reasonably anticipated to be a human carcinogen. Talc - 3 - Silica gel, pptd., cryst.-free- 3 - Titanium Dioxide - 2B - Product/ingredient name NTPIARCOSHA Date of issue/Date of revision :11/29/2022Date of previous issue :6/20/2022 Version:8 10/15 21330 FEATHER-RITE QUALITY LIGHTWEIGHT AUTOBODY FILLER SHW-85-NA-GHS-US Section 11. Toxicological information Not available. Information on the likely routes of exposure Inhalation :Harmful if inhaled. May be fatal if swallowed and enters airways.:Ingestion Skin contact :Causes skin irritation. Causes serious eye irritation.:Eye contact Causes damage to organs through prolonged or repeated exposure.General : May cause cancer. Risk of cancer depends on duration and level of exposure.Carcinogenicity : No known significant effects or critical hazards.Mutagenicity : Suspected of damaging the unborn child.Teratogenicity : Developmental effects :No known significant effects or critical hazards. Fertility effects :No known significant effects or critical hazards. Symptoms related to the physical, chemical and toxicological characteristics Skin contact Ingestion Inhalation Adverse symptoms may include the following: reduced fetal weight increase in fetal deaths skeletal malformations Adverse symptoms may include the following: nausea or vomiting reduced fetal weight increase in fetal deaths skeletal malformations Adverse symptoms may include the following: irritation redness reduced fetal weight increase in fetal deaths skeletal malformations : : : Eye contact :Adverse symptoms may include the following: pain or irritation watering redness Potential chronic health effects Delayed and immediate effects and also chronic effects from short and long term exposure Numerical measures of toxicity Acute toxicity estimates :Not available. Potential acute health effects Potential immediate effects :Not available. Short term exposure Potential delayed effects:Not available. Potential immediate effects :Not available. Long term exposure Potential delayed effects:Not available. Date of issue/Date of revision :11/29/2022Date of previous issue :6/20/2022 Version:8 11/15 21330 FEATHER-RITE QUALITY LIGHTWEIGHT AUTOBODY FILLER SHW-85-NA-GHS-US Section 11. Toxicological information Oral 15544.54 mg/kg Inhalation (gases) 16248.44 ppm Inhalation (vapors) 69.22 mg/l Route ATE value Section 12. Ecological information LogPow BCF Potential Bioaccumulative potential Other adverse effects :No known significant effects or critical hazards. Product/ingredient name Styrene - 13.49 low Toxicity Calcium Carbonate Acute LC50 >56000 ppm Fresh water Fish – Gambusia affinis – Adult96 hours
Chronic NOEC 16.5 mg/l Fresh waterFish – Rhamdia quelen 30 days
Styrene Acute EC50 78000 g/l Marine waterAlgae – Skeletonema costatum96 hours
Acute EC50 4700 g/l Fresh water Daphnia – Daphnia magna 48 hours
Acute LC50 52 mg/l Marine water Crustaceans – Artemia salina48 hours
Acute LC50 4020 g/l Fresh water Fish – Pimephales promelas 96 hours
Titanium Dioxide Acute LC50 >1000000 g/l Marine waterFish – Fundulus heteroclitus96 hours
Product/ingredient name SpeciesResult Exposure
Persistence and degradability
Soil/water partition
coefficient (KOC)
:Not available.
Mobility in soil
Not available.
Section 13. Disposal considerations
The generation of waste should be avoided or minimized wherever possible. Disposal
of this product, solutions and any by-products should at all times comply with the
requirements of environmental protection and waste disposal legislation and any
regional local authority requirements. Dispose of surplus and non-recyclable products
via a licensed waste disposal contractor. Waste should not be disposed of untreated to
the sewer unless fully compliant with the requirements of all authorities with jurisdiction.
Waste packaging should be recycled. Incineration or landfill should only be considered
when recycling is not feasible. This material and its container must be disposed of in a
safe way. Care should be taken when handling emptied containers that have not been
cleaned or rinsed out. Empty containers or liners may retain some product residues.
Vapor from product residues may create a highly flammable or explosive atmosphere
inside the container. Do not cut, weld or grind used containers unless they have been
cleaned thoroughly internally. Avoid dispersal of spilled material and runoff and contact
with soil, waterways, drains and sewers.
:Disposal methods
Date of issue/Date of revision :11/29/2022Date of previous issue :6/20/2022 Version:8 12/15
21330 FEATHER-RITE QUALITY LIGHTWEIGHT AUTOBODY
FILLER
SHW-85-NA-GHS-US

Section 14. Transport information
RESIN SOLUTION
3
III
RESIN SOLUTION
3
III
UN1866 UN1866
This product may
be re-classified as
“Combustible
Liquid,” unless
transported by
vessel or aircraft.
Non-bulk
packages (less
than or equal to
119 gal) of
combustible
liquids are not
regulated as
hazardous
materials in
package sizes
less than the
product reportable
quantity.
Emergency
schedules F-E, S-
E
DOT
Classification
IMDG
UN number
UN proper
shipping name
Transport
hazard class(es)
Packing group
Additional
information
Environmental
hazards
Special precautions for user
Transport in bulk according
to IMO instruments
No. No.
Not available.
:
Proper shipping name :
Not available.
:
TDG
Classification
UN1866
RESIN SOLUTION
3
III
No.
Product classified
as per the
following sections
of the
Transportation of
Dangerous Goods
Regulations:
2.18-2.19 (Class
3).
Mexico
Classification
UN1866
RESIN SOLUTION
3
III
No.
–
Multi-modal shipping descriptions are provided for informational purposes and do not
consider container sizes. The presence of a shipping description for a particular
mode of transport (sea, air, etc.), does not indicate that the product is packaged
suitably for that mode of transport. All packaging must be reviewed for suitability prior
to shipment, and compliance with the applicable regulations is the sole responsibility
of the person offering the product for transport. People loading and unloading
dangerous goods must be trained on all of the risks deriving from the substances
and on all actions in case of emergency situations.
IATA
UN1866
RESIN
SOLUTION
3
III
No.
–
127
ERG No.
127 127
ERG No. ERG No.
Date of issue/Date of revision :11/29/2022Date of previous issue :6/20/2022 Version:8 13/15
21330 FEATHER-RITE QUALITY LIGHTWEIGHT AUTOBODY
FILLER
SHW-85-NA-GHS-US

Section 15. Regulatory information
SARA 313
SARA 313 (40 CFR 372.45) supplier notification can be found on the Environmental Data Sheet.
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other
reproductive harm.
California Prop. 65
Australia inventory (AIIC): Not determined.
China inventory (IECSC): Not determined.
Japan inventory (CSCL): Not determined.
Japan inventory (ISHL): Not determined.
Korea inventory (KECI): Not determined.
New Zealand Inventory of Chemicals (NZIoC): Not determined.
Philippines inventory (PICCS): Not determined.
Taiwan Chemical Substances Inventory (TCSI): Not determined.
Thailand inventory: Not determined.
Turkey inventory: Not determined.
Vietnam inventory: Not determined.
International regulations
International lists :
Section 16. Other information
11/29/2022
History
Date of printing
Date of issue/Date of
revision
Version
Date of previous issue
:
:
:
:
11/29/2022
6/20/2022
8
Hazardous Material Information System (U.S.A.)
3
2
0
*
Health
Flammability
Physical hazards
Caution: HMIS ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4
representing significant hazards or risks. Although HMIS ratings and the associated label are not required on
SDSs or products leaving a facility under 29 CFR 1910.1200, the preparer may choose to provide them. HMIS
ratings are to be used with a fully implemented HMIS program. HMIS is a registered trademark and service
mark of the American Coatings Association, Inc.
The customer is responsible for determining the PPE code for this material. For more information on HMIS
Personal Protective Equipment (PPE) codes, consult the HMIS Implementation Manual.
FLAMMABLE LIQUIDS – Category 3 On basis of test data
ACUTE TOXICITY (inhalation) – Category 4 Calculation method
SKIN CORROSION/IRRITATION – Category 2 Calculation method
SERIOUS EYE DAMAGE/ EYE IRRITATION – Category 2A Calculation method
CARCINOGENICITY – Category 1B Calculation method
TOXIC TO REPRODUCTION – Category 2 Calculation method
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) – Category 1 Calculation method
ASPIRATION HAZARD – Category 1 Calculation method
Procedure used to derive the classification
Classification Justification
Date of issue/Date of revision :11/29/2022Date of previous issue :6/20/2022 Version:8 14/15
21330 FEATHER-RITE QUALITY LIGHTWEIGHT AUTOBODY
FILLER
SHW-85-NA-GHS-US

Section 16. Other information
It is recommended that each customer or recipient of this Safety Data Sheet (SDS) study it carefully and consult
resources, as necessary or appropriate, to become aware of and understand the data contained in this SDS and
any hazards associated with the product. This information is provided in good faith and believed to be accurate
as of the effective date herein. However, no warranty, express or implied, is given. The information presented
here applies only to the product as shipped. The addition of any material can change the composition, hazards
and risks of the product. Products shall not be repackaged, modified, or tinted except as specifically instructed
by the manufacturer, including but not limited to the incorporation of products not specified by the manufacturer,
or the use or addition of products in proportions not specified by the manufacturer. Regulatory requirements
are subject to change and may differ between various locations and jurisdictions. The customer/buyer/user is
responsible to ensure that his activities comply with all country, federal, state, provincial or local laws. The
conditions for use of the product are not under the control of the manufacturer; the customer/buyer/user is
responsible to determine the conditions necessary for the safe use of this product. The customer/buyer/user
should not use the product for any purpose other than the purpose shown in the applicable section of this SDS
without first referring to the supplier and obtaining written handling instructions. Due to the proliferation of
sources for information such as manufacturer-specific SDS, the manufacturer cannot be responsible for SDSs
obtained from any other source.
Indicates information that has changed from previously issued version.
Key to abbreviations :
Notice to reader
ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships, 1973
as modified by the Protocol of 1978. (“Marpol” = marine pollution)
N/A = Not available
SGG = Segregation Group
UN = United Nations
Date of issue/Date of revision :11/29/2022Date of previous issue :6/20/2022 Version:8 15/15
21330 FEATHER-RITE QUALITY LIGHTWEIGHT AUTOBODY
FILLER
SHW-85-NA-GHS-US