PRO-SET SBE-160 Resin
Safety Data Sheet
According to the Hazard Communication Standard (CFR29 1910.1200) HazCom 2012 and the Hazardous Products
Regulations (HPR) WHMIS 2015
Date of issue: 09/10/2015 Revision date: 01/25/2019 Version: SBE-160-2019a
01/25/2019 EN (English) Page 1
SECTION 1: Identification
Identification
Product form : Mixtures
Product name : PRO-SET SBE-160 Resin
Product code : SBE-160, SBE-160-1, SBE-160-2, SBE-160-4
Relevant identified uses of the substance or mixture and uses advised against
Recommended use : Resin for composites
Details of the supplier of the safety data sheet
Manufacturer
Gougeon Brothers, Inc
100 Patterson Ave.
Bay City, MI 48706 – U.S.A.
T 866-937-8797 or 989-684-7286
www.westsystem.com
Emergency telephone number
Emergency number : CHEMTREC 1 (800) 424-9300
CHEMTREC International +1 (703) 527-3887 24 hr
SECTION 2: Hazard(s) identification
Classification of the substance or mixture
Skin Irrit. 2
Eye Irrit. 2A
Skin Sens. 1
Aquatic Chronic 2
Label elements
Hazard pictograms (GHS) :
GHS07
GHS09
Signal word (GHS)
:
Warning
Hazard statements (GHS)
:
Causes skin irritation. May cause an allergic skin reaction. Causes serious eye irritation. Toxic to aquatic life with long lasting effects
Precautionary statements (GHS)
:
Avoid breathing dust/fume/gas/mist/vapours/spray. Wash hands thoroughly after handling. Contaminated work clothing must not be allowed out of
the workplace. Avoid release to the environment. Wear protective gloves/protective clothing/eye protection/face protection. If on skin: Wash with
plenty of water. If skin irritation or rash occurs: Get medical advice/attention. If in eyes: Rinse cautiously with water for several minutes. Remove
contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention. Take off contaminated clothing
and wash it before reuse. Collect spillage. Dispose of contents/container to hazardous or special waste collection point, in accordance with local,
regional, national and/or international regulation
Other hazards
No additional information available.
Unknown acute toxicity
No additional information available.
SECTION 3: Composition/information on ingredients
Substance
Not applicable
PRO-SET SBE-160 Resin
Safety Data Sheet
According to the Hazard Communication Standard (CFR29 1910.1200) HazCom 2012 and the Hazardous Products Regulations (HPR) WHMIS 2015
01/25/2019 EN (English) 2/7
Mixtures
Name Product identifier HPR %
Oxirane, 2,2′-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bis-, homopolymer
(CAS No) 25085-99-8 60 – 80
Phenol, polymer with formaldehyde, glycidyl ether
(CAS No) 28064-14-4 10 – 30
Benzyl alcohol
(CAS No) 100-51-6 1 – 5
Benzoic acid, 4[{(methylphenylamino) methylene} amino]-, ethyl ester
(CAS No) 57834-33-0 1 – 5
The exact chemical identity and/or exact percentage (concentration) of each ingredient may be held as confidential business information (CBI). Any
ingredient not disclosed in this section may have been determined not to be hazardous to health or the environment, or it may be present at a level
below its disclosure threshold.
SECTION 4: First aid measures
Description of first aid measures
First-aid measures after inhalation : If breathing is difficult, remove victim to fresh air and keep at rest in a position comfortable for
breathing. Get medical advice/attention if you feel unwell.
First-aid measures after skin contact : In case of contact, immediately flush skin with plenty of water. Remove contaminated clothing
and shoes. Wash contaminated clothing before reuse. If skin irritation or rash occurs: Get
medical advice/attention.
First-aid measures after eye contact : In case of contact, immediately flush eyes with plenty of water for at least 15 minutes. If easy to
do, remove contact lenses, if worn. If irritation persists, get medical attention.
First-aid measures after ingestion : If swallowed, do NOT induce vomiting unless directed to do so by medical personnel. Never give
anything by mouth to an unconscious person. Get medical advice/attention if you feel unwell.
Most important symptoms and effects, both acute and delayed
Symptoms/injuries after inhalation : May cause respiratory tract irritation.
Symptoms/injuries after skin contact : Causes skin irritation. Symptoms may include redness, edema, drying, defatting and cracking
of the skin. May cause an allergic skin reaction.
Symptoms/injuries after eye contact : Causes serious eye irritation. Symptoms may include discomfort or pain, excess blinking and
tear production, with marked redness and swelling of the conjunctiva.
Symptoms/injuries after ingestion : May be harmful if swallowed. May cause stomach distress, nausea or vomiting.
Indication of any immediate medical attention and special treatment needed
Symptoms may not appear immediately. In case of accident or if you feel unwell, seek medical advice immediately (show the label or SDS where
possible).
SECTION 5: Firefighting measures
Extinguishing media
Suitable extinguishing media : Foam. Carbon dioxide. Dry chemical.
Unsuitable extinguishing media : Do not use a heavy water stream.
Special hazards arising from the substance or mixture
Fire hazard : Products of combustion may include, and are not limited to: oxides of carbon, phenolics.
Reactivity : No dangerous reaction known under conditions of normal use.
Advice for firefighters
Protection during firefighting : Keep upwind of fire. Wear full fire fighting turn-out gear (full Bunker gear) and respiratory
protection (SCBA).
SECTION 6: Accidental release measures
Personal precautions, protective equipment and emergency procedures
General measures : Use personal protection recommended in Section 8. Isolate the hazard area and deny entry to
unnecessary and unprotected personnel.
For non-emergency personnel
No additional information available
For emergency responders
No additional information available
Environmental precautions
Prevent from entering into soil, ditches, sewers, waterways and/or groundwater. See Section 12, Ecological Information.
PRO-SET SBE-160 Resin
Safety Data Sheet
According to the Hazard Communication Standard (CFR29 1910.1200) HazCom 2012 and the Hazardous Products Regulations (HPR) WHMIS 2015
01/25/2019 EN (English) 3/7
Methods and material for containment and cleaning up
For containment : Stop leak if safe to do so. Contain and/or absorb spill with inert material (e.g. sand, vermiculite),
then place in a suitable container. Do not flush to sewer or allow to enter waterways. Use
appropriate Personal Protective Equipment (PPE).
Methods for cleaning up : Scoop up material and place in a disposal container. Provide ventilation.
Reference to other sections
See section 8 for further information on protective clothing and equipment and section 13 for advice on waste disposal.
SECTION 7: Handling and storage
Precautions for safe handling
Precautions for safe handling : Avoid contact with skin and eyes. Avoid breathing dust/fume/gas/mist/vapours/spray. Do not
swallow. Handle and open container with care. When using do not eat, drink or smoke. When
mixed with epoxy curing agents this product causes an exothermic reaction, which in large
masses, can produce enough heat to damage or ignite surrounding materials and emit fumes
and vapors that vary widely in composition and toxicity.
Hygiene measures : Launder contaminated clothing before reuse. Wash hands before eating, drinking, or smoking.
Contaminated work clothing should not be allowed out of the workplace.
Conditions for safe storage, including any incompatibilities
Storage conditions : Keep out of the reach of children. Keep container tightly closed. Store in dry, cool, well-
ventilated area. Protect from moisture. Storage temperature : 40 F (4 C) – 120 F (49 C).
SECTION 8: Exposure controls/personal protection
Control parameters
Oxirane, 2,2′-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bis-, homopolymer (25085-99-8)
Not applicable
Phenol, polymer with formaldehyde, glycidyl ether (28064-14-4)
Not applicable
Benzyl alcohol (100-51-6)
AIHA WEEL TWA (ppm) 10 ppm
Benzoic acid, 4[{(methylphenylamino) methylene} amino]-, ethyl ester (57834-33-0)
Not applicable
Exposure controls
Appropriate engineering controls : Use ventilation adequate to keep exposures (airborne levels of dust, fume, vapor, etc.) below
recommended exposure limits.
Hand protection : Wear chemically resistant protective gloves.
Eye protection : Wear eye/face protection.
Skin and body protection : Wear suitable protective clothing.
Respiratory protection : In case of insufficient ventilation, wear suitable respiratory equipment. Respirator selection
must be based on known or anticipated exposure levels, the hazards of the product and the
safe working limits of the selected respirator.
Environmental exposure controls : Maintain levels below Community environmental protection thresholds.
Other information : Do not eat, smoke or drink where material is handled, processed or stored. Wash hands
carefully before eating or smoking. Handle according to established industrial hygiene and
safety practices.
SECTION 9: Physical and chemical properties
Information on basic physical and chemical properties
Physical state : Liquid
Appearance : No data available
Colour : Colourless
Odour : Mild
Odour threshold : No data available
pH : No data available
Melting point : No data available
PRO-SET SBE-160 Resin
Safety Data Sheet
According to the Hazard Communication Standard (CFR29 1910.1200) HazCom 2012 and the Hazardous Products Regulations (HPR) WHMIS 2015
01/25/2019 EN (English) 4/7
Freezing point : No data available
Boiling point : > 400 F (204 C) Estimated based on ingredient data.
Flash point : > 200 F (93 C) Estimated based on ingredient data.
Relative evaporation rate (butylacetate=1) : No data available
Flammability (solid, gas) : Non flammable.
Vapour pressure : No data available
Relative vapour density at 20 C : Heavier than air. (Estimated based on ingredient data.)
Relative density : 1.17
Solubility : No data available
Partition coefficient n-octanol/water : No data available
Auto-ignition temperature : No data available
Decomposition temperature : No data available
Viscosity, kinematic : No data available
Viscosity, dynamic : No data available
Explosive limits : No data available
Explosive properties : No data available
Oxidising properties : No data available
Other information
Bulk density : 9.7 lb/gal (1.17 kg/L)
SECTION 10: Stability and reactivity
Reactivity : No dangerous reaction known under conditions of normal use.
Chemical stability : Stable under normal storage conditions.
Possibility of hazardous reactions : No dangerous reaction known under conditions of normal use. A mass of more than one pound
of product plus an aliphatic amine will cause irreversible polymerization with significant heat
buildup. Strong acids, bases, amines and mercaptans can cause polymerization.
Conditions to avoid : Heat. Incompatible materials.
Incompatible materials : Strong acids. Bases. Amines. Mercaptans.
Hazardous decomposition products : May include, and are not limited to: oxides of carbon, phenolics.
SECTION 11: Toxicological information
Information on toxicological effects
Oxirane, 2,2′-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bis-, homopolymer (25085-99-8)
LD50 oral rat > 15000 mg/kg
LD50 dermal rabbit > 23000 mg/kg
Phenol, polymer with formaldehyde, glycidyl ether (28064-14-4)
LD50 oral rat > 2000 mg/kg
LD50 dermal rat 2000 mg/kg
Benzyl alcohol (100-51-6)
LD50 oral rat 1620 mg/kg
LC50 inhalation rat > 4.18 mg/l/4h
Benzoic acid, 4[{(methylphenylamino) methylene} amino]-, ethyl ester (57834-33-0)
LD50 oral rat 1000 – 2000 mg/kg
Acute toxicity (oral) : Not classified.
Acute toxicity (dermal) : Not classified.
Acute toxicity (inhalation) : Not classified.
Skin corrosion/irritation : Causes skin irritation.
Serious eye damage/irritation : Causes serious eye irritation.
Respiratory or skin sensitization : May cause an allergic skin reaction.
Germ cell mutagenicity : Not classified.
Carcinogenicity : Not classified.
Reproductive toxicity : Not classified.
PRO-SET SBE-160 Resin
Safety Data Sheet
According to the Hazard Communication Standard (CFR29 1910.1200) HazCom 2012 and the Hazardous Products Regulations (HPR) WHMIS 2015
01/25/2019 EN (English) 5/7
Specific target organ toxicity (single
exposure)
: Not classified.
Specific target organ toxicity (repeated
exposure)
: Not classified.
Aspiration hazard : Not classified.
Symptoms/injuries after inhalation : May cause respiratory tract irritation.
Symptoms/injuries after skin contact : Causes skin irritation. Symptoms may include redness, edema, drying, defatting and cracking
of the skin. May cause an allergic skin reaction.
Symptoms/injuries after eye contact : Causes serious eye irritation. Symptoms may include discomfort or pain, excess blinking and
tear production, with marked redness and swelling of the conjunctiva.
Symptoms/injuries after ingestion : May be harmful if swallowed. May cause stomach distress, nausea or vomiting.
Other information : Likely routes of exposure: ingestion, inhalation, skin and eye.
SECTION 12: Ecological information
Toxicity
Ecology – general : Toxic to aquatic life with long lasting effects.
Benzyl alcohol (100-51-6)
LC50 fish 1 460 mg/l (Exposure time: 96 h – Species: Pimephales promelas [static])
EC50 Daphnia 1 23 mg/l (Exposure time: 48 h – Species: water flea)
LC50 fish 2 10 mg/l (Exposure time: 96 h – Species: Lepomis macrochirus [static])
Persistence and degradability
PRO-SET SBE-160 Resin
Persistence and degradability Not established.
Bioaccumulative potential
PRO-SET SBE-160 Resin
Bioaccumulative potential Not established.
Benzyl alcohol (100-51-6)
Partition coefficient n-octanol/water 1.1
Mobility in soil
PRO-SET SBE-160 Resin
Ecology – soil No additional information available.
Other adverse effects
Effect on the global warming : No known effects from this product.
Name CAS# Ecotoxicity Classification Information
Oxirane, 2,2′-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bis-, homopolymer
25085-99-8 Aquatic Chronic Cat. 2
Phenol, polymer with formaldehyde, glycidyl ether
28064-14-4 Aquatic Chronic Cat. 2
Benzyl alcohol
100-51-6 Not Classified
Benzoic acid, 4[{(methylphenylamino) methylene} amino]-, ethyl ester 57834-33-0 Not Classified
Other information : Avoid release to the environment.
SECTION 13: Disposal considerations
Waste treatment methods
Product/Packaging disposal
recommendations
: Avoid release to the environment. This material must be disposed of in accordance with all
local, state, provincial, and federal regulations. The generation of waste should be avoided or
minimized wherever possible.
PRO-SET SBE-160 Resin
Safety Data Sheet
According to the Hazard Communication Standard (CFR29 1910.1200) HazCom 2012 and the Hazardous Products Regulations (HPR) WHMIS 2015
01/25/2019 EN (English) 6/7
SECTION 14: Transport information
Department of Transportation (DOT) and Transportation of Dangerous Goods (TDG)
In accordance with DOT/TDG
Not regulated
Transport by sea
In accordance with IMDG
UN-No. (IMDG) : 3082
Proper Shipping Name (IMDG) : ENVIRONMENTALLY HAZA RDOUS SUBSTANCE, LIQUID, N.O.S. (Epoxy resin)
Class (IMDG) : 9
Packing group (IMDG) : III
EmS Number : F-A, S-F
Marine pollutant : Yes
Transport by air
In accordance with IATA
UN-No. (IATA) : 3082
Proper Shipping Name (IATA) : Environmentally hazardous substance, liquid, n.o.s. (Epoxy resin)
Class (IATA) : 9
Packing group (IATA) : III
Marine pollutant : Yes
SECTION 15: Regulatory information
Federal regulations
All components of this product are listed, or excluded from listing, on the United States Environmental Protection Agency Toxic Substances
Control Act (TSCA) inventory.
All components of this product are listed, or excluded from listing, on the Canadian DSL (Domestic Substances List) and NDSL (Non-Domestic
Substances List) inventories.
Oxirane, 2,2′-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bis-, homopolymer (25085-99-8)
EPA TSCA Regulatory Flag XU – XU – indicates a substance exempt from reporting under the Inventory Update Reporting
Rule, i.e, Partial Updating of the TSCA Inventory Data Base Production and Site Reports (40
CFR 710(C)).
Phenol, polymer with formaldehyde, glycidyl ether (28064-14-4)
EPA TSCA Regulatory Flag XU – XU – indicates a substance exempt from reporting under the Inventory Update Reporting
Rule, i.e, Partial Updating of the TSCA Inventory Data Base Production and Site Reports (40
CFR 710(C)).
Epichlorohydrin (106-89-8)
Listed on the United States SARA Section 302
Subject to reporting requirements of United States SARA Section 313
CERCLA RQ 100 lb
SARA Section 302 Threshold Planning
Quantity (TPQ)
1000 lb
SARA Section 313 – Emission Reporting 0.1 %
International regulations
No additional information available
US State regulations
California Proposition 65 – This product contains, or may contain, trace quantities of a substance(s) known to the state of California to cause
cancer, developmental and/or reproductive harm
Epichlorohydrin (106-89-8)
U.S. – California –
Proposition 65 –
Carcinogens List
U.S. – California –
Proposition 65 –
Developmental Toxicity
U.S. – California –
Proposition 65 –
Reproductive Toxicity –
Female
U.S. – California –
Proposition 65 –
Reproductive Toxicity –
Male
No significant risk
level (NSRL)
Yes No No Yes 9 g/day
PRO-SET SBE-160 Resin
Safety Data Sheet
According to the Hazard Communication Standard (CFR29 1910.1200) HazCom 2012 and the Hazardous Products Regulations (HPR) WHMIS 2015
01/25/2019 EN (English) 7/7
Benzyl alcohol (100-51-6)
U.S. – Pennsylvania – RTK (Right to Know) List
Epichlorohydrin (106-89-8)
U.S. – New Jersey – Right to Know Hazardous Substance List
U.S. – Pennsylvania – RTK (Right to Know) – Environmental Hazard List
U.S. – Pennsylvania – RTK (Right to Know) – Special Hazardous Substances
U.S. – Pennsylvania – RTK (Right to Know) List
SECTION 16: Other information
Date of issue : 09/10/2015
Revision date : 01/25/2019
Other information : None.
NFPA health hazard : 2
NFPA fire hazard : 1
NFPA reactivity : 1
HMIS III Rating
Health : 2 Moderate Hazard
Flammability : 1 Slight Hazard
Physical : 1 Slight Hazard
Disclaimer: We believe the statements, technical information and recommendations contained herein are reliable, but they are given without warranty or guarantee of any kind. The information contained
in this document applies to this specific material as supplied. It may not be valid for this material if it is used in combination with any other materials. It is the user s responsibility to satisfy oneself as to the
suitability and completeness of this information for the user s own particular use.