CR3040CCG_SDS.pdf

INDEX

CR3040CC
CR3040CCCG
CR3040CCCQ
CR3040CCG
CR3040CCQ

Composite Resource Clear Casting Resin
Safety Data SheetCR3040CC
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
Date of issue:12/17/2014 Revision date: Supersedes: Version:1.0
12/17/2014 EN(English) SDS ID:CR3040CC Page 1
SECTION 1:Identification of the substance/mixture and of the company/undertaking
1.1. Product identifier
Product form :Mixture
Trade name :Composite Resource Clear Casting Resin
CAS No :Mixture
Product code :CR3040CCCP,CR3040CCCQ,CR3040CCG , CR3040CCF
Other means of identification :DISTRIBUTED BY REVCHEM COMPOSITES, INC.
1.2. Relevant identified uses of the substance or mixture and uses advised against
Use of the substance/mixture :Clear Casting Resin
1.3. Details of the supplier of the safety data sheet
Composite Resources is supplied by Revchem Composites. 2720 South Willow Ave., Bloomington, CA 92316 1-800-281-4975
1.4. Emergency telephone number
Emergency number :800.424.9300
CHEMTREC: 1-800-424-9300
SECTION 2:Hazards identification
2.1. Classification of the substance or mixture
GHS-US classification
Flam. Liq. 3H226
Skin Irrit. 2H315
Eye Irrit. 2AH319
Carc. 2 H351
2.2. Label elements
GHS-US labelling
Hazard pictograms (GHS-US) :
GHS02 GHS07 GHS08
Signal word (GHS-US) :Warning
Hazard statements (GHS-US) :H226-Flammable liquid and vapour
H315-Causes skin irritation
H319-Causes serious eye irritation
H351-Suspected of causing cancer
Precautionary statements (GHS-US) :P201-Obtain special instructions before use
P202-Do not handle until all safety precautions have been read and understood
P210-Keep away from sparks.-No smoking
P233-Keep container tightly closed
P240-Ground/bond container and receiving equipment
P241-Use explosion-proof electrical equipment
P242-Use only non-sparking tools
P243-Take precautionary measures against static discharge
P264-Wash … thoroughly after handling
P280-Wear protective clothing
P302+P352-IF ON SKIN: Wash with plenty of soap and water
P303+P361+P353-IF ON SKIN (or hair): Remove/Take off immediately all contaminated
clothing. Rinse skin with water/shower
P305+P351+P338-If in eyes: Rinse cautiously with water for several minutes. Remove contact
lenses, if present and easy to do. Continue rinsing
P308+P313-IF exposed or concerned: Get medical advice/attention
P321-Specific treatment (see … on this label)
P332+P313-If skin irritation occurs: Get medical advice/attention
P337+P313-If eye irritation persists: Get medical advice/attention
P362-Take off contaminated clothing and wash before reuse
P370+P378-In case of fire: Use carbon dioxide (CO2), dry chemical powder, foam for
extinction

Composite Resource Clear Casting Resin
Safety Data SheetCR3040CC
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
12/17/2014 EN(English) SDS ID:CR3040CC 2/8
P403+P235-Store in a well-ventilated place. Keep cool
P405-Store locked up
P501-Dispose of contents/container to …
2.3. Other hazards
No additional information available
2.4. Unknown acute toxicity (GHS-US)
No data available
SECTION 3:Composition/information on ingredients
3.1. Substance
Not applicable
Full text of H-phrases: see section 16
3.2. Mixture
Name Product identifier % GHS-US classification
Unsaturated Polyester Resin (CAS No)TRADE SECRET 62-64 Not classified
Styrene, inhibited (CAS No)100-42-5 37 Flam. Liq. 3, H226
Acute Tox. 4 (Inhalation:vapour),
H332
Skin Irrit. 2, H315
Eye Irrit. 2A, H319
Carc. 2, H351
SECTION 4:First aid measures
4.1. Description of first aid measures
First-aid measures general :Never give anything by mouth to an unconscious person. If you feel unwell, seek medical advice
(show the label where possible). Suspected of causing cancer.
First-aid measures after inhalation :Assure fresh air breathing. Allow the victim to rest.
First-aid measures after skin contact :Rinse skin with water/shower. Remove/Take off immediately all contaminated clothing.Wash
with plenty of soap and water. Wash contaminated clothing before reuse. If skin irritation occurs:
Get medical advice/attention. Specific treatment (see … on this label).
First-aid measures after eye contact :Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to
do. Continue rinsing. If eye irritation persists: Get medical advice/attention.
First-aid measures after ingestion :Rinse mouth. Do NOT induce vomiting. Obtain emergency medical attention.
4.2. Most important symptoms and effects, both acute and delayed
Symptoms/injuries after skin contact :Causes skin irritation.
Symptoms/injuries after eye contact :Causes serious eye irritation.
4.3. Indication of any immediate medical attention and special treatment needed
No additional information available
SECTION 5:Firefighting measures
5.1. Extinguishing media
Suitable extinguishing media :Foam. Dry powder. Carbon dioxide. Water spray. Sand.
Unsuitable extinguishing media :Do not use a heavy waterstream.
5.2. Special hazards arising from the substance or mixture
Fire hazard :Extremely flammable liquid and vapour.
Explosion hazard :May form flammable/explosive vapour-air mixture.
5.3. Advice for firefighters
Firefighting instructions :Use water spray or fog for cooling exposed containers. Exercise caution when fighting any
chemical fire. Avoid (reject) fire-fighting water to enter environment.
Protection during firefighting :Do not enter fire area without proper protective equipment, including respiratory protection.
SECTION 6:Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
General measures :Remove ignition sources. Use special care to avoid static electric charges. No naked lights. No
smoking.

Composite Resource Clear Casting Resin
Safety Data SheetCR3040CC
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
12/17/2014 EN(English) SDS ID:CR3040CC 3/8
6.1.1.For non-emergency personnel
Emergency procedures :Evacuate unnecessary personnel.
6.1.2.For emergency responders
Protective equipment :Equip cleanup crew with proper protection.
Emergency procedures :Ventilate area.
6.2. Environmental precautions
Prevent entry to sewers and public waters. Notify authorities if liquid enters sewers or public waters.
6.3. Methods and material for containment and cleaning up
Methods for cleaning up :Soak up spills with inert solids, such as clay ordiatomaceous earth as soon as possible. Collect
spillage. Store away from other materials.
6.4. Reference to other sections
See Heading 8. Exposure controls and personal protection.
SECTION 7:Handling and storage
7.1. Precautions for safe handling
Additional hazards when processed :Handle empty containers with care because residual vapours are flammable.
Precautions for safe handling :Wash hands and other exposed areas with mild soap and water before eat, drink or smoke and
when leaving work. Provide good ventilation in process area to prevent formation of vapour. No
naked lights. No smoking. Take precautionary measures against static discharge. Use only non-
sparking tools. Obtain special instructions before use. Do not handle until all safety precautions
have been read and understood.
Hygiene measures :Wash … thoroughly after handling.
7.2. Conditions for safe storage, including any incompatibilities
Technical measures :Ground/bond container and receiving equipment. Use explosion-proof
electrical/ventilating/lighting/ equipment.
Storage conditions :Keep only in the original container in a cool, well ventilated place away from : Heat sources.
Keep in fireproof place. Keep container tightly closed.
Incompatible products :Strong bases. strongacids.
Incompatible materials :Sources of ignition. Direct sunlight. Heat sources.
7.3. Specific end use(s)
No additional information available
SECTION 8:Exposure controls/personal protection
8.1. Control parameters
styrene, inhibited (100-42-5)
USA ACGIH ACGIH TWA (ppm) 20 ppm
USA ACGIH ACGIH STEL (ppm) 40 ppm
8.2. Exposure controls
Personal protective equipment :Avoid all unnecessary exposure.
Hand protection :Wear protective gloves.
Eye protection :Chemical goggles or safety glasses.
Skin and body protection :Wear suitable protective clothing.
Respiratory protection :Wear approved mask.
Other information :When using, do not eat, drink or smoke.
SECTION 9:Physical and chemical properties
9.1. Information on basic physical and chemical properties
Physical state :Liquid
Appearance :Clear, colorless liquid
Colour :Clear
Odour :characteristic.
Odour threshold :No data available
pH :No data available
Relative evaporation rate (butylacetate=1):No data available

Composite Resource Clear Casting Resin
Safety Data SheetCR3040CC
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
12/17/2014 EN(English) SDS ID:CR3040CC 4/8
Relative evaporation rate (ether=1) :Slower than ether
Melting point :No data available
Freezing point :No data available
Boiling point :145.22 C Initial Boiling Point for Styrene @ 760.00 mm Hg(293.40 F)
Flash point :31.1 C for Volatile Component (88 F)
Auto-ignition temperature :No data available
Decomposition temperature :No data available
Flammability (solid, gas) :No data available
Vapour pressure :4.3 mm Hg Vapor pressure for Styrene at 20 C (68 F)
Relativevapour density at 20 C :3.6 (Air = 1)
Relative density :1-1.2 Relative Density @ 25 C (77 F)
Solubility :No data available
Log Pow :No data available
Log Kow :No data available
Viscosity, kinematic :No data available
Viscosity,dynamic :No data available
Explosive properties :No data available
Oxidising properties :No data available
Explosive limits :No data available
9.2. Other information
No additional information available
SECTION 10:Stability and reactivity
10.1.Reactivity
No additional information available
10.2.Chemical stability
Stable under normal conditions. Not established. Extremely flammable liquid and vapour. May form flammable/explosive vapour-air mixture.
10.3.Possibility of hazardous reactions
Not established.
10.4.Conditions to avoid
Direct sunlight. Extremely high or low temperatures. . Heat. Overheating. Open flame.
10.5.Incompatible materials
strong acids. Strong bases.
10.6.Hazardous decomposition products
fume. Carbon monoxide. Carbon dioxide. May release flammable gases.
SECTION 11:Toxicological information
11.1.Information on toxicological effects
Acute toxicity :Not classified
styrene, inhibited (100-42-5)
LD50 oral rat 5000 mg/kg (>6000 mg/kg bodyweight; Rat; Rat)
LD50 dermal rat 2820 mg/kg (>2000 mg/kg bodyweight; Rat; Rat; Experimental value)
LD50 dermal rabbit 5010 mg/kg (Rabbit)
LC50 inhalation rat (mg/l) 12 mg/l/4h (Rat)
LC50 inhalation rat (ppm) 2770 ppm/4h (Rat)
ATE CLP (oral) 5000.000 mg/kg bodyweight
ATE CLP (dermal) 2820.000 mg/kg bodyweight
ATE CLP (gases) 2770.000 ppmv/4h
ATE CLP (vapours) 12.000 mg/l/4h
ATE CLP (dust,mist) 12.000 mg/l/4h
Skin corrosion/irritation :Causes skin irritation.

Composite Resource Clear Casting Resin
Safety Data SheetCR3040CC
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
12/17/2014 EN(English) SDS ID:CR3040CC 5/8
Serious eye damage/irritation :Causes serious eye irritation.
Respiratory or skin sensitisation :Not classified
Germ cell mutagenicity :Not classified
Based on available data, the classification criteria are not met
Carcinogenicity :Suspected of causing cancer.
styrene, inhibited (100-42-5)
IARC group 2B-Possibly Carcinogenic to Humans
Reproductive toxicity :Not classified
Based on available data, the classification criteria are not met
Specific target organ toxicity (single exposure):Not classified
Specific target organ toxicity (repeated
exposure)
:Not classified
Based on available data, the classification criteria are not met
Aspiration hazard :Not classified
Based on available data, the classification criteria are not met
Potential Adverse human health effects and
symptoms
:Based on available data, the classification criteria are not met.
Symptoms/injuries after skin contact :Causes skin irritation.
Symptoms/injuries after eye contact :Causes serious eye irritation.
Likely routes of exposure :Inhalation
SECTION 12:Ecological information
12.1.Toxicity
styrene, inhibited (100-42-5)
LC50 fishes 1 25 mg/l (96 h; Lepomis macrochirus)
LC50 other aquatic organisms 1 10-100 mg/l (96 h)
EC50 Daphnia 1 23 mg/l (48 h; Daphnia magna; LOCOMOTOR EFFECT)
LC50 fish 2 32 mg/l(96 h; Pimephales promelas)
EC50 Daphnia 2 27 mg/l (24 h; Daphnia magna)
TLM fish 1 25.1 mg/l (96 h; Lepomis macrochirus; SOFT WATER)
TLM fish 2 46.4 mg/l (96 h; Pimephales promelas; SOFT WATER)
TLM other aquatic organisms 1 10-100,96 h
Threshold limit other aquatic organisms 1 10-100,96 h; Pseudomonas putida
Threshold limit other aquatic organisms 272 mg/l
Threshold limit algae 1 > 200 mg/l (192 h; Scenedesmus quadricauda; INHIBITORY)
Threshold limit algae 2 67 mg/l (Microcystis aeruginosa; INHIBITORY)
12.2.Persistence and degradability
Composite Resource Clear Casting Resin(Mixture)
Persistence and degradability Not established.
styrene, inhibited (100-42-5)
Persistence and degradability Readily biodegradable in water. Not readily biodegradable in water. Forming sediments in
water. Non degradable in the soil. Adsorbs into the soil. Photodegradation in the air. Not
established.
Chemical oxygen demand (COD) 2.80 g O /g substance
ThOD 3.07 g O /g substance
BOD (% of ThOD) 0.42 % ThOD
Unsaturated Polyester Resin (TRADE SECRET)
Persistence and degradability Not established.
12.3.Bioaccumulative potential
Composite Resource Clear Casting Resin(Mixture)
Bioaccumulative potential Not established.

Composite Resource Clear Casting Resin
Safety Data SheetCR3040CC
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
12/17/2014 EN(English) SDS ID:CR3040CC 6/8
styrene, inhibited (100-42-5)
BCF fish 1 12-77 (QSAR)
BCF fish 2 35.5 (Carassius auratus)
Log Pow 2.95-3.16 (Experimental value)
Bioaccumulative potential Low potential for bioaccumulation (BCF < 500). Not established. Unsaturated Polyester Resin (TRADE SECRET) Bioaccumulative potential Not established. 12.4.Mobility in soil styrene, inhibited (100-42-5) Surface tension 0.032 N/m (19 C) 12.5.Other adverse effects Other information :Avoid release to the environment. SECTION 13:Disposal considerations 13.1.Waste treatment methods Waste disposal recommendations :Dispose in a safe manner in accordance with local/national regulations. Dispose of contents/container to ... Additional information :Handle empty containers with care because residual vapours are flammable. Ecology-waste materials :Avoid release to the environment. SECTION 14:Transport information In accordance with DOT UN-No.(DOT) :UN1866 DOT Proper Shipping Name :RESIN SOLUTION Department of Transportation (DOT) Hazard Classes :3-Class3-Flammable and combustible liquid 49 CFR 173.120 Hazard labels (DOT) :3-Flammable liquid Packing group (DOT) :III-Minor Danger Additional information Other information :No supplementary information available. ADR Transport document description :UN UN1866 RESIN SOLUTION, III Packing group (ADR) :III Transport by sea No additional information available Air transport No additional information available SECTION 15:Regulatory information 15.1. US Federal regulations Composite ResourceClear Casting Resin (Mixture) RQ (Reportable quantity, section 304 of EPA's List of Lists) : 1000 lb styrene, inhibited (100-42-5) RQ (Reportable quantity, section 304 of EPA's List of Lists) : 1000 lb Composite Resource Clear Casting Resin Safety Data SheetCR3040CC according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 12/17/2014 EN(English) SDS ID:CR3040CC 7/8 styrene, inhibited (100-42-5) SARA Section 311/312 Hazard Classes Immediate (acute) health hazard Reactive hazard Fire hazard Delayed (chronic) health hazard 15.2. International regulations CANADA No additional information available EU-Regulations No additional information available Classification according to Regulation (EC) No. 1272/2008 [CLP] Not classified Classification according to Directive 67/548/EEC or 1999/45/EC Not classified 15.2.2.National regulations styrene, inhibited (100-42-5) Listed on EPA's Hazardous Air Pollutants (HAPS) 15.3. US State regulations styrene, inhibited (100-42-5) U.S.-California- Proposition 65- Carcinogens List U.S.-California- Proposition 65- Developmental Toxicity U.S.-California- Proposition 65- Reproductive Toxicity- Female U.S.-California- Proposition 65- Reproductive Toxicity-Male No significance risk level (NSRL) styrene, inhibited (100-42-5) U.S.-Massachusetts-Right To Know List U.S.-New Jersey-Right to Know Hazardous Substance List U.S.-Pennsylvania-RTK (Right to Know)-Environmental Hazard List SECTION 16:Other information Other information :None. Full text of H-phrases: see section 16: ------Acute Tox. 4 (Inhalation:vapour) Acute toxicity (inhalation:vapour) Category 4 ------Carc. 2 Carcinogenicity, Category 2 ------Eye Irrit. 2A Serious eye damage/eye irritation, Category 2A ------Flam. Liq. 3 Flammable liquids, Category 3 ------Skin Irrit. 2 Skin corrosion/irritation, Category 2 ------H226 Flammable liquid and vapour ------H315 Causes skin irritation ------H319 Causes serious eye irritation ------H332 Harmful if inhaled ------H351 Suspected of causing cancer SDS US (GHS HazCom 2012) Composite Resource Clear Casting Resin Safety Data SheetCR3040CC according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 12/17/2014 EN(English) SDS ID:CR3040CC 8/8 To the best of our knowledge this SDS is accurate. The the extent allowed by law, this statement is made inlieu of an other warranties, expressed or implied including but not limited to any implied warranty of merchantability or fitness for a particular purpose and is in lieu of any other obligations or liability on the part of Dura Technoligies, Inc.