Polyester Resin Solution
Product name
Product type
Section 1. Identification
Chemical family Aromatic.
Relevant identified uses of the substance or mixture and uses advised against
SDS No. NA-1504:747 (Version: 4.1)
Uses advised against
Identified uses Used in the manufacture of thermoset plastic parts.
No additional information.
A563-FSA-07
SAFETY DATA SHEET
Date of issue: 03/01/2020
Date of previous issue: 05/15/2019
Emergency telephone number
Supplier’s details
CHEMTREC Within USA and Canada
CHEMTREC Outside USA and Canada
CANUTEC Within Canada
+1 (800) 424-9300
+1 (703) 527-3887
+1 (613) 996-6666
CCN1023
AOC
955 Highway 57 East
Collierville, TN 38017
Phone Number: (901) 854-2800
Hours: 8AM-5pm (Central Time) Mon-Fri
AOC
38 Royal Road
Guelph, Ontario Canada N1H 1G3
Phone Number: (519) 821-5180
Hours: 8am-5pm (Eastern) Mon-Fri
E-Mail: aoc.sds@aocresins.com
Website: www.aocresins.com
United States: Canada:
Section 2. Hazards identification
OSHA/HCS status
FLAMMABLE LIQUIDS Category 3 H226
ACUTE TOXICITY (Inhalation) Category 4 H332
SKIN IRRITATION Category 2 H315
EYE IRRITATION Category 2A H319
CARCINOGENICITY Category 2 H351
REPRODUCTIVE TOXICITY Category 2 H361d
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) Category 3 H335
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) Category 1 H372
ASPIRATION HAZARD Category 1 H304
Classification of the substance or mixture
Signal word
Danger
Hazard statements
H226: Flammable liquid and vapor.
H332: Harmful if inhaled.
H319: Causes serious eye irritation.
H315: Causes skin irritation.
H361d: Suspected of damaging the unborn child.
H351: Suspected of causing cancer.
H304: May be fatal if swallowed and enters airways.
H335: May cause respiratory irritation.
H372: Causes damage to organs through prolonged or repeated exposure if inhaled. (hearing organs, kidneys)
Hazard pictograms
Precautionary statements
GHS label elements
General
This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).
Page: 1 of 9Date of issue: 03/01/2020
Date of previous issue: 05/15/2019NA-1504:747 (Version: 4.1)
A563-FSA-07
Section 2. Hazards identification
Prevention
P201: Obtain special instructions before use.
P202: Do not handle until all safety precautions have been read and understood.
P280: Wear protective gloves/protective clothing/eye protection/face protection.
P210: Keep away from heat, sparks, open flames and hot surfaces. – No smoking.
P240: Ground/bond container and receiving equipment.
P241: Use explosion-proof electrical/ventilating/lighting/material-handling equipment.
P242: Use only non-sparking tools.
P243: Take precautionary measures against static discharge.
P233: Keep container tightly closed.
P271: Use only outdoors or in a well-ventilated area.
P260: Do not breathe vapor or mist.
P270: Do not eat, drink or smoke when using this product.
P264: Wash hands thoroughly after handling.
Response
P314: Get medical attention if you feel unwell.
P308+P313: IF exposed or concerned: Get medical attention.
P304+P340: IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
P312: Call a POISON CENTER or physician if you feel unwell.
P370+P378: In case of fire: Use dry chemical, CO , water spray (fog) or foam.
P301+P310: IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.
P331: Do NOT induce vomiting.
P308+P313: IF exposed or concerned: Get medical advice/attention.
P303+P361+P353: IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower.
P362+P364: Take off contaminated clothing and wash it before reuse.
P332+P313: If skin irritation occurs: Get medical attention.
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue
rinsing.
P337+P313: If eye irritation persists: Get medical attention.
P391: Collect spillage.
Storage
P405: Store locked up.
P403+P235: Store in a well-ventilated place. Keep cool.
P233: Keep container tightly closed.
Disposal
P501: Dispose of contents and container in accordance with all local, regional, national and international regulations.
P101: If medical advice is needed, have product container or label at hand.
P102: Keep out of reach of children.
Hazards not otherwise classified
None known.
Section 3. Composition/information on ingredients
Ingredient name CAS number %
There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are
classified as hazardous to health or the environment and hence require reporting in this section.
Substance/mixture
Occupational exposure limits, if available, are listed in Section 8.
Mixture.
styrene 100-42-5 30.0
cobalt bis(2-ethylhexanoate) 136-52-7 0.3
Section 4. First aid measures
Immediately flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Use of buffered baby
shampoo will aid in removal. If irritation persists, get medical attention.
In case of contact, immediately flush skin with plenty of water. Remove contaminated clothing and shoes. If irritation persists, seek
medical attention. Wash contaminated clothing before reuse. Clean shoes thoroughly before reuse.
Move the victim to a safe area as soon as possible. Allow the victim to rest in a well-ventilated area. If breathing is difficult, give oxygen.
If the victim is not breathing, perform mouth-to-mouth resuscitation. Seek immediate medical attention.
Eye contact
Skin contact
Inhalation
Description of necessary first aid measures
Page: 2 of 9Date of issue: 03/01/2020
Date of previous issue: 05/15/2019NA-1504:747 (Version: 4.1)
A563-FSA-07
Section 4. First aid measures
Wash out mouth with water. Remove dentures if any. Stop if the exposed person feels sick as vomiting may be dangerous. Do not
induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit does not
enter the lungs. Seek immediate medical attention.
Ingestion
Notes to physician
Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled.
Most important symptoms/effects, acute and delayed
See toxicological information (Section 11)
Indication of immediate medical attention and special treatment needed, if necessary
Irritating to mouth, throat and stomach.
Causes serious eye irritation.
Causes skin irritation.
Harmful if inhaled. May cause respiratory irritation. May cause drowsiness or dizziness.
Eye contact
Skin contact
Inhalation
Ingestion
Over-exposure signs/symptoms
Eye contact
Inhalation
Skin contact
Ingestion
Adverse symptoms may include the following: pain or irritation, watering, redness.
Adverse symptoms may include the following: respiratory tract irritation, coughing.
Adverse symptoms may include the following: irritation, redness.
Adverse symptoms may include the following: Irritating to mouth, throat and stomach.
Section 5. Fire-fighting measures
Fire water contaminated with this material must be contained and prevented from being discharged to any waterway, sewer or drain.
Hazardous thermal decomposition products
Specific hazards arising from the chemical
Decomposition products may include the following materials: carbon dioxide, carbon monoxide nitrogen oxides
Flammable liquid and vapor. In a fire or if heated, a pressure increase will occur and the container may burst, with the risk of a
subsequent explosion. The vapor/gas is heavier than air and will spread along the ground. Vapors may accumulate in low or confined
areas or travel a considerable distance to a source of ignition and flash back. Runoff to sewer may create fire or explosion hazard. This
material is harmful to aquatic life with long lasting effects. Fire water contaminated with this material must be contained and prevented
from being discharged to any waterway, sewer or drain.
Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated
in positive pressure mode.
Special protective equipment for fire-fighters
Use dry chemical, CO , water spray (fog) or foam.
Extinguishing media
Do not use water jet.
Suitable extinguishing media
Unsuitable extinguishing media
Special protective actions for fire-fighters
Section 6. Accidental release measures
Personal precautions, protective equipment and emergency procedures
For non-emergency personnel
For emergency responders
No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Do not touch or walk
through spilled material. Shut off all ignition sources. No flares, smoking or flames in hazard area. Avoid breathing vapor or mist.
Provide adequate ventilation.
If specialised clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials.
Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment. See also the information in
“For non-emergency personnel”.
Page: 3 of 9Date of issue: 03/01/2020
Date of previous issue: 05/15/2019NA-1504:747 (Version: 4.1)
A563-FSA-07
Section 6. Accidental release measures
Environmental precautions
Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water courses,
basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and collect spillage with non-
combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local
regulations (see Section 13). Use spark-proof tools and explosion-proof equipment. Dispose of via a licensed waste disposal contractor.
Contaminated absorbent material may pose the same hazard as the spilled product. Note: see Section 1 for emergency contact
information and Section 13 for waste disposal.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the
product has caused environmental pollution (sewers, waterways, soil or air). Water polluting material. May be harmful to the environment
if released in large quantities.
Stop leak if without risk. Move containers from spill area. Dilute with water and mop up if water-soluble. Alternatively, or if water-insoluble,
absorb with an inert dry material and place in an appropriate waste disposal container. Use spark-proof tools and explosion-proof
equipment. Dispose of via a licensed waste disposal contractor.
Methods and materials for containment and cleaning up
Small spill
Large spill
Section 7. Handling and storage
Advice on general occupational hygiene
Conditions for safe storage, including any incompatibilities
Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash
hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating
areas. See also Section 8 for additional information on hygiene measures.
Store in accordance with local regulations. Store in a segregated and approved area. Store in original container protected from direct
sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Eliminate all
ignition sources. Segregate from oxidizing materials. Keep container tightly closed and sealed until ready for use. Containers that have
been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate
containment to avoid environmental contamination. Refer to the product label and/or technical data sheet for further information.
Protective measures
Put on appropriate personal protective equipment (see Section 8). Eating, drinking and smoking should be prohibited in areas where this
material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove
contaminated clothing and protective equipment before entering eating areas. Do not breathe vapor or mist. Do not ingest. Avoid contact
with eyes, skin and clothing. Avoid release to the environment. Use only with adequate ventilation. Wear appropriate respirator when
ventilation is inadequate. Do not enter storage areas and confined spaces unless adequately ventilated. Keep in the original container or
an approved alternative made from a compatible material, kept tightly closed when not in use. Store and use away from heat, sparks,
open flame or any other ignition source. Use only non-sparking tools. Take precautionary measures against electrostatic discharges.
Empty containers retain product residue and can be hazardous. Do not reuse container.
Precautions for safe handling
styrene ACGIH TLV (United States, 3/2019). Absorbed through skin.
TWA: 20 ppm 8 hours.
STEL: 40 ppm 15 minutes.
OSHA PEL Z2 (United States, 2/2013).
TWA: 100 ppm 8 hours.
CEIL: 200 ppm
AMP: 600 ppm 5 minutes.
NIOSH REL (United States, 10/2016).
TWA: 50 ppm 10 hours.
TWA: 215 mg/m 10 hours.
STEL: 100 ppm 15 minutes.
STEL: 425 mg/m 15 minutes.
cobalt bis(2-ethylhexanoate) OSHA PEL (United States).
TWA: 0.1 mg/m
ACGIH TLV (United States, 3/2019). Skin sensitizer. Inhalation
sensitizer.
TWA: 0.02 mg/m , (as Co) 8 hours.
Section 8. Exposure controls/personal protection
Ingredient name Exposure limits
Appropriate engineering controls
Control parameters
Occupational exposure limits
Page: 4 of 9Date of issue: 03/01/2020
Date of previous issue: 05/15/2019NA-1504:747 (Version: 4.1)
A563-FSA-07
Section 8. Exposure controls/personal protection
Hand protection
Use a properly fitted, air-purifying or air-fed respirator complying with an approved standard if a risk assessment indicates this is
necessary. Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the safe working
limits of the selected respirator.
Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products
if a risk assessment indicates this is necessary.
Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid
exposure to liquid splashes, mists or dusts.
Eye/face protection
Respiratory protection
Body protection
Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be
approved by a specialist before handling this product.
Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or other engineering controls to keep worker
exposure to airborne contaminants below any recommended or statutory limits. The engineering controls also need to keep gas, vapor or
dust concentrations below any lower explosive limits. Use explosion-proof ventilation equipment.
Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end
of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Ensure that eyewash stations
and safety showers are close to the workstation location.
Hygiene measures
Individual protection measures
Other skin protection
Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks
involved and should be approved by a specialist before handling this product.
Section 9. Physical and chemical properties
Physical state
Melting point
Vapor pressure
Relative density
Vapor density
Solubility
Liquid.
23.8 F / 30.6 C (Styrene)
1.1 (Water = 1)
3.6 (Air = 1) (Styrene )
<2.58 mm Hg@ 70 F / 21.1 C per ASTM D 323
Slight.
Aromatic.Odor
pH
Purple.Color
Evaporation rate < 1 (Butyl acetate = 1)
Auto-ignition temperature
Flash point
914 F / 490 C (Styrene)
88 F / 31 C (Styrene)
Not available.
Not applicable.
Viscosity Not available.
0.01 - 0.1 ppm (Styrene)Odor threshold
Partition coefficient: n-octanol/water
Appearance
Boiling point 293 F / 145 C (Styrene)
Flammability (solid, gas) Not applicable.
Lower and upper explosive (flammable)
limits
Lower: 1.1% Upper: 6.1% (Styrene)
Molecular weight 1,000 to 15,000
Decomposition temperature Not available.
Section 10. Stability and reactivity
Conditions to avoid
The product is stable. Stable under recommended storage and handling conditions (see Section 7).
Chemical stability
Possibility of hazardous reactions
Under normal conditions of storage and use, hazardous reactions will not occur.
Reactivity
No specific test data related to reactivity available for this product or its ingredients.
Page: 5 of 9Date of issue: 03/01/2020
Date of previous issue: 05/15/2019NA-1504:747 (Version: 4.1)
A563-FSA-07
Section 10. Stability and reactivity
Hazardous decomposition products
Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld, braze, solder, drill, grind or expose containers to heat
or sources of ignition.
Under normal conditions of storage and use, hazardous decomposition products should not be produced.
Reactive or incompatible with the following materials: oxidizing materials
Incompatible materials
Section 11. Toxicological information
Acute toxicity
styrene LC50 Inhalation Gas. Rat 2770 ppm 4 hours
LC50 Inhalation Vapor Rat 11800 mg/m 4 hours
LC50 Inhalation Vapor Rat 5634.2 ppm 4 hours
LD50 Oral Rat 2650 mg/kg -
cobalt bis(2-ethylhexanoate) LD50 Dermal Rabbit >5 g/kg –
LD50 Oral Rat 1.22 g/kg –
Ingredient name Result Species Dose Exposure
Carcinogenicity
Mutagenicity
Teratogenicity
Reproductive toxicity
Irritation/Corrosion
styrene Eyes – Mild irritant Human – 50 ppm –
Eyes – Moderate irritant Rabbit – 24 hours 100 mg-
Eyes – Severe irritant Rabbit – 100 mg –
Skin – Mild irritant Rabbit – 500 mg –
Skin – Moderate irritant Rabbit – 100 % –
Ingredient name Result Score Exposure Observation
Sensitization
Species
Inhalation
Harmful if inhaled. May cause respiratory irritation. May cause drowsiness or dizziness.
Skin contact
Causes skin irritation.
Causes serious eye irritation.
Eye contact
Specific target organ toxicity (single exposure)
Specific target organ toxicity (repeated exposure)
Aspiration hazard
Information on toxicological effects
Potential acute health effects
Classification
styrene – 2A Reasonably anticipated to be a human carcinogen.
cobalt bis(2-ethylhexanoate) – 2B Reasonably anticipated to be a human carcinogen.
Ingredient name NTPIARCACGIH
May cause sensitization by skin contact.
No known significant effects or critical hazards.
1) Negative Study A published study concluded that the mechanism for producing cancer in mice exposed to styrene
is not applicable in human metabolism. (June 2013 Pharmacology & Toxicology 66 (2013))
2) Negative Study A recent update to an extensive study of reinforced plastic workers from 1948-1977 concluded that
there was no coherent evidence that styrene exposure increased risk of cancer (March 2013 Epidemiology Vol. 24
Issue 2)
3) Positive Study Styrene induced pulmonary toxicity and carcinogenicity in mice was shown to be caused by a
metabolite of styrene, probably styrene oxide. (Dec.2001 Toxicology Vol.169 Issue 2)
Suspected of damaging the unborn child.
No known significant effects or critical hazards.
May cause respiratory irritation.
A study of long term effects of workers exposed to styrene levels in the range of 25-35 ppm, 8 hour TWA, indicated a possible mild
hearing loss.
May be fatal if swallowed and enters airways.
Page: 6 of 9Date of issue: 03/01/2020
Date of previous issue: 05/15/2019NA-1504:747 (Version: 4.1)
A563-FSA-07
Section 11. Toxicological information
Irritating to mouth, throat and stomach.
Ingestion
Symptoms related to the physical, chemical and toxicological characteristics
Skin contact
Ingestion
Adverse symptoms may include the following: respiratory tract irritation, coughing.
Adverse symptoms may include the following: Irritating to mouth, throat and stomach.
Adverse symptoms may include the following: irritation, redness.
Eye contact
Adverse symptoms may include the following: pain or irritation, watering, redness.
Inhalation
Section 12. Ecological information
LogPow BCF Potential
Bioaccumulative potential
Other adverse effects
No known effect according to our database.
styrene 0.35 13.49 low
cobalt bis(2-ethylhexanoate) – 15600 high
Toxicity
styrene Acute EC50 1400 g/l Fresh water Algae – Pseudokirchneriella
subcapitata
72 hours
Acute EC50 720 g/l Fresh water Algae – Pseudokirchneriella
subcapitata
96 hours
Acute EC50 4700 g/l Fresh water Daphnia – Daphnia magna 48 hours
Acute LC50 52 mg/l Marine water Crustaceans – Artemia salina 48 hours
Acute LC50 4020 g/l Fresh water Fish – Pimephales promelas 96 hours
Chronic NOEC 63 g/l Fresh water Algae – Pseudokirchneriella
subcapitata
96 hours
Ingredient name SpeciesResult Exposure
Persistence and degradability
Soil/water partition coefficient (KOC)
Not available.
Mobility in soil
Not available.
Ingredient name
Section 13. Disposal considerations
The generation of waste should be avoided or minimized wherever possible. Empty containers or liners may retain some product residues.
Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Disposal of this product, solutions and any by-
products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local
authority requirements. Avoid disposal. Attempt to use product completely in accordance with intended use. Waste packaging should be
recycled. Incineration or landfill should only be considered when recycling is not feasible.
Disposal methods
The information in this section contains generic advice and guidance. The list of Identified Uses in Section 1 should be consulted for any
available use-specific information provided in the Exposure Scenario(s).
Special precautions
This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers that have not been
cleaned or rinsed out. Empty containers or liners may retain some product residues. Do not cut, weld or grind used containers unless they
have been cleaned thoroughly internally. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers.
Section 14. Transport information
Resin Solution
3
UN1866UN number
Proper shipping name
Transport hazard class(es)
DOT /TDG / IMDG/IMO / ICAO/IATA and National regulations.
Page: 7 of 9Date of issue: 03/01/2020
Date of previous issue: 05/15/2019NA-1504:747 (Version: 4.1)
A563-FSA-07
Section 14. Transport information
IIIPacking group
Additional information US regulations require the reporting of spills when the amount exceeds the Reportable
Quantity (RQ) for specific components of this material. See CERCLA in Section 15,
Regulatory Information, for the Reportable Quantities.
Environmental hazards Marine pollutant: No.
Special precautions for user Transport within user s premises: always transport in closed containers that are upright and
secure. Ensure that persons transporting the product know what to do in the event of an
accident or spillage.
IMDGEmergency schedules (EmS): F-E, S-E
Remarks: FP- 31 C
IATANo additional information.
Section 15. Regulatory information
International regulations lists
All components are listed or exempted.
SARA 313
Ingredient name
styrene 100-42-5
cobalt bis(2-ethylhexanoate) 136-52-7
Form R – Reporting
requirements
SARA 311/312
United States inventory (TSCA 8b)
Australia (AICS) All components are listed or exempted.
Canada (DSL) All components are listed or exempted.
China (IECSC) All components are listed or exempted.
Europe (EINECS) Not determined.
Japan Japan inventory (ENCS): Not determined.
Japan inventory (ISHL): Not determined.
Republic of Korea (KECI) All components are listed or exempted.
Malaysia (EHS Register) Not determined.
New Zealand (NZIoC) All components are listed or exempted.
Philippines (PICCS) Not determined.
Taiwan (CSNN) All components are listed or exempted.
CAS number
California Prop. 65
State regulations
styrene – 1000 lbs. (453.6 kg)CERCLA RQ –
WARNING: This product can expose you to Styrene, which is known to the State of California to cause cancer. For more information go
to www.P65Warnings.ca.gov.
Per the June 13, 2016 Federal Register notice, EPA harmonized the EPCRA 311/312 hazard categories with the 2012 OSHA hazard
communication standard for classifying and labeling of chemicals (i.e. GHS). Please refer to Section 2 of the SDS to identify the appropriate
hazard categories for reporting purposes.
U.S. Federal regulations
Section 16. Other information
National Fire Protection Association (U.S.A.)
Reprinted with permission from NFPA 704-2001, Identification of the Hazards of Materials for Emergency Response Copyright 1997, National Fire Protection Association, Quincy, MA 02269. This
reprinted material is not the complete and official position of the National Fire Protection Association, on the referenced subject which is represented only by the standard in its entirety.
1
3
2
Health
Special
Instability
Flammability
Page: 8 of 9Date of issue: 03/01/2020
Date of previous issue: 05/15/2019NA-1504:747 (Version: 4.1)
A563-FSA-07
Section 16. Other information
History
Version
Prepared by
AOC is a registered trademark of the AOC group of companies.
The information contained in this data sheet is based on laboratory data and field experience. We believe this information to be reliable, but do not
guarantee its applicability to the user s process or assume any liability for occurrences arising out of its use. The user, by accepting the products
as described herein, agrees to be responsible for thoroughly testing each such product before committing it to production.
Altek , Atryl , Atryl TCA , Chroma-Tek , EcoTek , FirePel , Hydropel , Moldtru , PulTru , Vibrin , Vicast , Vipel , the AOC name, the
AOC logo, and the Trusted Solutions logo are registered trademarks of the AOC group of companies.
Our recommendations should not be construed as inducements to infringe any patent or violate any law, safety code or insurance regulation.
The information and recommendations contained herein are to the best of our knowledge accurate and reliable, but no rights whatsoever may be
derived by any party other than those expressly agreed to with a selling entity of the AOC group of companies in a legally binding agreement. AOC
hereby makes no warranty of any kind, express or implied, including those of merchantability and fitness for purpose. Unless explicitly agreed to in
writing by AOC otherwise, all offers, quotations, sales and deliveries of AOC products are subject to the general conditions of sale of AOC.
Notice to reader
Date of previous issue
Indicates information that has changed from previously issued version.
Key to abbreviations ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by
the Protocol of 1978. (“Marpol” = marine pollution)
UN = United Nations
03/01/2020
05/15/2019
4.1
Copyright 2001, National Fire Protection Association, Quincy, MA 02269. This warning system is intended to be interpreted and applied only by properly trained individuals to identify fire, health and
reactivity hazards of chemicals. The user is referred to certain limited number of chemicals with recommended classifications in NFPA 49 and NFPA 325, which would be used as a guideline only. Whether
the chemicals are classified by NFPA or not, anyone using the 704 systems to classify chemicals does so at their own risk.
AOC Corporate Regulatory Affairs
This Safety Data Sheet (SDS) and its content are the confidential and proprietary information of AOC and it may not be modified, altered,
deconstructed, or presented in any other manner, without the explicit authorization of AOC and/or its legal counsel.
Date of issue
Page: 9 of 9Date of issue: 03/01/2020
Date of previous issue: 05/15/2019NA-1504:747 (Version: 4.1)
A563-FSA-07