CLEAR CASTING RESIN
Unsaturated Polyester Resin
Liquid.
SAFETY DATA SHEET
Product identifier
Other means of identification
Product type
Emergency telephone
number (with hours of
operation)
SECTION 1: Identification of the substance/mixture and of the
company/undertaking
:
:
:
:
Supplier’s details :INTERPLASTIC CORPORATION
1225 Willow Lake Boulevard
St. Paul, MN 55110-5145
651.481.6860
CLEAR CASTING RESIN
Relevant identified uses of the substance or mixture and uses advised against
Product code :SIL95BA-41
Industrial applications.
CHEMTREC 24-Hour Emergency Telephone
US and Canada 800.424.9300
Outside US and Canada +1 703.741.5970
SECTION 2: Hazards identification
FLAMMABLE LIQUIDS – Category 3
ACUTE TOXICITY (inhalation) – Category 4
SKIN IRRITATION – Category 2
EYE IRRITATION – Category 2A
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Respiratory tract
irritation) – Category 3
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) (hearing
organs) – Category 1
Classification of the
substance or mixture
:
Signal word :Danger
Hazard statements :H226 – Flammable liquid and vapor.
H332 – Harmful if inhaled.
H319 – Causes serious eye irritation.
H315 – Causes skin irritation.
H335 – May cause respiratory irritation.
H372 – Causes damage to organs through prolonged or repeated exposure.
(hearing organs)
Hazard pictograms :
Precautionary statements
Prevention :P280 – Wear protective gloves. Wear protective clothing. Wear eye or face
protection. P210 – Keep away from heat, hot surfaces, sparks, open flames and
other ignition sources. No smoking. P271 – Use only outdoors or in a well-ventilated
area. P260 – Do not breathe vapor. P270 – Do not eat, drink or smoke when using
this product. P264 – Wash hands thoroughly after handling.
GHS label elements
Percentage of the mixture consisting of ingredient(s) of unknown dermal toxicity:
37%
Date of issue/Date of revision :9/30/2018Date of previous issue :No previous validationVersion:0.01 1/12
CLEAR CASTING RESIN Mexico SIL95BA-41
SECTION 2: Hazards identification
Response :P314 – Get medical attention if you feel unwell. P304 + P340 + P312 – IF INHALED:
Remove person to fresh air and keep comfortable for breathing. Call a POISON
CENTER or physician if you feel unwell. P303 + P361 + P353 – IF ON SKIN (or
hair): Take off immediately all contaminated clothing. Rinse skin with water. P302 +
P352 + P362+P364 – IF ON SKIN: Wash with plenty of soap and water. Take off
contaminated clothing and wash it before reuse. P332 + P313 – If skin irritation
occurs: Get medical attention. P305 + P351 + P338 – IF IN EYES: Rinse cautiously
with water for several minutes. Remove contact lenses, if present and easy to do.
Continue rinsing. P337 + P313 – If eye irritation persists: Get medical attention.
Storage :P405 – Store locked up.
Disposal :P501 – Dispose of contents and container in accordance with all local, regional,
national and international regulations. No Code(s) – Do not pressurize, cut, weld,
braze, solder, drill, grind or expose containers to heat or sources of ignition.
Other hazards which do not
result in classification
:None known.
SECTION 3: Composition/information on ingredients
styrene 25 – 50 100-42-5
Ingredient name CAS number%
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health or the environment and hence require
reporting in this section.
Other means of
identification
:Unsaturated Polyester Resin
Substance/mixture :
Occupational exposure limits, if available, are listed in Section 8.
Mixture
Wash out mouth with water. Remove dentures if any. Remove victim to fresh air
and keep at rest in a position comfortable for breathing. If material has been
swallowed and the exposed person is conscious, give small quantities of water to
drink. Stop if the exposed person feels sick as vomiting may be dangerous. Do not
induce vomiting unless directed to do so by medical personnel. If vomiting occurs,
the head should be kept low so that vomit does not enter the lungs. Get medical
attention following exposure or if feeling unwell. Never give anything by mouth to an
unconscious person. If unconscious, place in recovery position and get medical
attention immediately. Maintain an open airway. Loosen tight clothing such as a
collar, tie, belt or waistband.
Flush contaminated skin with plenty of water. Remove contaminated clothing and
shoes. Continue to rinse for at least 10 minutes. Get medical attention. Wash
clothing before reuse. Clean shoes thoroughly before reuse.
Remove victim to fresh air and keep at rest in a position comfortable for breathing.
If it is suspected that fumes are still present, the rescuer should wear an appropriate
mask or self-contained breathing apparatus. If not breathing, if breathing is irregular
or if respiratory arrest occurs, provide artificial respiration or oxygen by trained
personnel. It may be dangerous to the person providing aid to give mouth-to-mouth
resuscitation. Get medical attention. If necessary, call a poison center or physician.
If unconscious, place in recovery position and get medical attention immediately.
Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or
waistband.
SECTION 4: First aid measures
Eye contact
Skin contact
Inhalation
Ingestion :
:
:
:
Description of necessary first aid measures
Immediately flush eyes with plenty of water, occasionally lifting the upper and lower
eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10
minutes. Get medical attention. Buffered baby shampoo will aid in removal of resin.
Date of issue/Date of revision :9/30/2018Date of previous issue :No previous validationVersion:0.01 2/12
CLEAR CASTING RESIN Mexico SIL95BA-41
SECTION 4: First aid measures
Protection of first-aiders:No action shall be taken involving any personal risk or without suitable training. If it
is suspected that fumes are still present, the rescuer should wear an appropriate
mask or self-contained breathing apparatus. It may be dangerous to the person
providing aid to give mouth-to-mouth resuscitation.
Notes to physician :Treat symptomatically. Contact poison treatment specialist immediately if large
quantities have been ingested or inhaled.
Specific treatments :No specific treatment.
Most important symptoms/effects, acute and delayed
Inhalation :Harmful if inhaled. May cause respiratory irritation.
No known significant effects or critical hazards.:Ingestion
Skin contact :Causes skin irritation.
Causes serious eye irritation.:Eye contact
Over-exposure signs/symptoms
Skin contact
Ingestion
Inhalation Adverse symptoms may include the following:
respiratory tract irritation
coughing
No specific data.
Adverse symptoms may include the following:
irritation
redness
:
:
:
Eye contact :Adverse symptoms may include the following:
pain or irritation
watering
redness
Potential acute health effects
See toxicological information (Section 11)
Indication of immediate medical attention and special treatment needed, if necessary
SECTION 5: Firefighting measures
Promptly isolate the scene by removing all persons from the vicinity of the incident if
there is a fire. No action shall be taken involving any personal risk or without
suitable training. Move containers from fire area if this can be done without risk.
Use water spray to keep fire-exposed containers cool.
Hazardous thermal
decomposition products
Specific hazards arising
from the chemical
Decomposition products may include the following materials:
carbon dioxide
carbon monoxide
Flammable liquid and vapor. Runoff to sewer may create fire or explosion hazard.
In a fire or if heated, a pressure increase will occur and the container may burst, with
the risk of a subsequent explosion. The vapor/gas is heavier than air and will
spread along the ground. Vapors may accumulate in low or confined areas or travel
a considerable distance to a source of ignition and flash back.
Fire-fighters should wear appropriate protective equipment and self-contained
breathing apparatus (SCBA) with a full face-piece operated in positive pressure
mode.
Special protective
equipment for fire-fighters
Use dry chemical, CO , water spray (fog) or foam.
Extinguishing media
:
:
:
Do not use water jet.
Suitable extinguishing
media
:
Unsuitable extinguishing
media
:
Special protective actions
for fire-fighters
:
Date of issue/Date of revision :9/30/2018Date of previous issue :No previous validationVersion:0.01 3/12
CLEAR CASTING RESIN Mexico SIL95BA-41
SECTION 6: Accidental release measures
Environmental precautions
Personal precautions, protective equipment and emergency procedures
:
:No action shall be taken involving any personal risk or without suitable training.
Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilled material. Shut off all ignition sources.
No flares, smoking or flames in hazard area. Avoid breathing vapor or mist.
Provide adequate ventilation. Wear appropriate respirator when ventilation is
inadequate. Put on appropriate personal protective equipment.
Avoid dispersal of spilled material and runoff and contact with soil, waterways,
drains and sewers. Inform the relevant authorities if the product has caused
environmental pollution (sewers, waterways, soil or air).
Large spill :
Small spill :
Methods and materials for containment and cleaning up
For non-emergency
personnel
For emergency responders:If specialized clothing is required to deal with the spillage, take note of any
information in Section 8 on suitable and unsuitable materials. See also the
information in “For non-emergency personnel”.
Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Dispose of via a licensed waste disposal contractor.
Absorb with an inert material and transfer the spilled material and absorbent to an
appropriate waste disposal container. Wear appropriate respirator when ventilation
is inadequate. Wear eye/face protection.
Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Approach release from upwind. Prevent entry into
sewers, water courses, basements or confined areas. Contain and collect spillage
with non-combustible, absorbent material e.g. sand, earth, vermiculite or
diatomaceous earth and place in container for disposal according to local
regulations (see Section 13). Dispose of via a licensed waste disposal contractor.
Contaminated absorbent material may pose the same hazard as the spilled product.
Note: see Section 1 for emergency contact information and Section 13 for waste
disposal. Wear appropriate respiratory protection. Wear protective clothing and
eye or face protection:
SECTION 7: Handling and storage
Advice on general
occupational hygiene
Conditions for safe storage,
including any
incompatibilities
Eating, drinking and smoking should be prohibited in areas where this material is
handled, stored and processed. Workers should wash hands and face before
eating, drinking and smoking. Remove contaminated clothing and protective
equipment before entering eating areas. See also Section 8 for additional
information on hygiene measures.
Do not store above the following temperature: 38 C (100.4 F). Store in accordance
with local regulations. Store in a segregated and approved area. Store in original
container protected from direct sunlight in a dry, cool and well-ventilated area, away
from incompatible materials (see Section 10) and food and drink. Eliminate all
ignition sources. Separate from oxidizing materials. Keep container tightly closed
and sealed until ready for use. Containers that have been opened must be carefully
resealed and kept upright to prevent leakage. Do not store in unlabeled containers.
Use appropriate containment to avoid environmental contamination. See Section 10
for incompatible materials before handling or use. Store containers in a safe place.
:
:
Protective measures Put on appropriate personal protective equipment (see Section 8). Do not breathe
vapor or mist. Do not ingest. Avoid contact with eyes, skin and clothing. Use only
with adequate ventilation. Wear appropriate respirator when ventilation is
inadequate. Do not enter storage areas and confined spaces unless adequately
ventilated. Keep in the original container or an approved alternative made from a
compatible material, kept tightly closed when not in use. Store and use away from
heat, sparks, open flame or any other ignition source. Use explosion-proof electrical
(ventilating, lighting and material handling) equipment. Use only non-sparking tools.
Take precautionary measures against electrostatic discharges. Empty containers
retain product residue and can be hazardous. Do not reuse container.
:
Precautions for safe handling
Date of issue/Date of revision :9/30/2018Date of previous issue :No previous validationVersion:0.01 4/12
CLEAR CASTING RESIN Mexico SIL95BA-41
styrene NOM-010-STPS-2014 (Mexico, 4/2016).
TWA: 20 ppm 8 hours.
STEL: 40 ppm 15 minutes.
SECTION 8: Exposure controls/personal protection
Ingredient name Exposure limits
Hand protection
Based on the hazard and potential for exposure, select a respirator that meets the
appropriate standard or certification. Respirators must be used according to a
respiratory protection program to ensure proper fitting, training, and other important
aspects of use.
Chemical-resistant, impervious gloves complying with an approved standard should
be worn at all times when handling chemical products if a risk assessment indicates
this is necessary. Considering the parameters specified by the glove manufacturer,
check during use that the gloves are still retaining their protective properties. It
should be noted that the time to breakthrough for any glove material may be
different for different glove manufacturers. In the case of mixtures, consisting of
several substances, the protection time of the gloves cannot be accurately
estimated.
Safety eyewear complying with an approved standard should be used when a risk
assessment indicates this is necessary to avoid exposure to liquid splashes, mists,
gases or dusts. If contact is possible, the following protection should be worn,
unless the assessment indicates a higher degree of protection: chemical splash
goggles.
Eye/face protection
Respiratory protection :
:
:
Body protection Personal protective equipment for the body should be selected based on the task
being performed and the risks involved and should be approved by a specialist
before handling this product. When there is a risk of ignition from static electricity,
wear anti-static protective clothing. For the greatest protection from static
discharges, clothing should include anti-static overalls, boots and gloves.
:
Environmental exposure
controls
:Emissions from ventilation or work process equipment should be checked to ensure
they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process
equipment will be necessary to reduce emissions to acceptable levels.
Appropriate engineering
controls
:Use only with adequate ventilation. Use process enclosures, local exhaust
ventilation or other engineering controls to keep worker exposure to airborne
contaminants below any recommended or statutory limits. The engineering controls
also need to keep gas, vapor or dust concentrations below any lower explosive
limits. Use explosion-proof ventilation equipment.
Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Wash contaminated clothing before reusing. Ensure that eyewash stations and
safety showers are close to the workstation location.
Hygiene measures :
Control parameters
Individual protection measures
Occupational exposure limits
Skin protection
Other skin protection :Appropriate footwear and any additional skin protection measures should be
selected based on the task being performed and the risks involved and should be
approved by a specialist before handling this product.
Date of issue/Date of revision :9/30/2018Date of previous issue :No previous validationVersion:0.01 5/12
CLEAR CASTING RESIN Mexico SIL95BA-41
SECTION 9: Physical and chemical properties
Physical state
Melting point
Vapor pressure
Relative density
Vapor density
Solubility
Liquid.
Not available.
0.9 to 1.3
3.6 [Air = 1]
0.67 kPa (5 mm Hg) [room temperature]
Not available.
Sweetish.Odor
pH
Colorless.Color
Evaporation rate <1 (butyl acetate = 1)
Auto-ignition temperature
Flash point
Not available.
Closed cup: 31 C (87.8 F)
Not available.
Not applicable.
Viscosity Not available.
0.1 ppmOdor threshold
Partition coefficient: n-
octanol/water
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Appearance
Boiling point :145 C (293 F)
Flammability (solid, gas):Not available.
Lower and upper explosive
(flammable) limits
:Lower: 0.9%
Upper: 6.8%
Decomposition temperature:Not available.
Solubility in water :Not applicable.
Molecular weight :Not applicable.
Flow time (ISO 2431) :Not available.
VOC content :37 % (w/w) As shipped, including monomers and additives.
SECTION 10: Stability and reactivity
Hazardous decomposition
products
Conditions to avoid Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld,
braze, solder, drill, grind or expose containers to heat or sources of ignition. Do not
allow vapor to accumulate in low or confined areas.
Under normal conditions of storage and use, hazardous decomposition products
should not be produced.
The product is stable.Chemical stability
Reactive or incompatible with the following materials:
oxidizing materials
:
:
:
Incompatible materials :
Possibility of hazardous
reactions
:Hazardous reactions or instability may occur under certain conditions of storage or
use.
Reactivity :No specific test data related to reactivity available for this product or its ingredients.
Reactive or incompatible with the following materials: metals, acids and alkalis.
Incompatible with alkali metals. Incompatible with some alkalis. Incompatible with
some strong acids. Incompatible with copper alloys, brass.
Hazardous polymerization may occur under certain conditions of storage or use.
Keep away from heat and direct sunlight. Keep away from heat and flame. Keep
away from oxidizing agents.
Date of issue/Date of revision :9/30/2018Date of previous issue :No previous validationVersion:0.01 6/12
CLEAR CASTING RESIN Mexico SIL95BA-41
SECTION 11: Toxicological information
Acute toxicity
styrene LC50 Inhalation Gas. Rat 2770 ppm 4 hours
LC50 Inhalation Vapor Rat 11800 mg/m 4 hours
LD50 Oral Rat 2650 mg/kg -
Product/ingredient nameResult Species Dose Exposure
Carcinogenicity
Not available.
Mutagenicity
Not available.
Teratogenicity
Not available.
Reproductive toxicity
Not available.
Irritation/Corrosion
styrene Eyes - Mild irritant Human - 50 parts per
million
-
Eyes - Moderate irritantRabbit - 24 hours 100
milligrams
-
Eyes - Severe irritantRabbit - 100
milligrams
-
Skin - Mild irritant Rabbit - 500
milligrams
-
Skin - Moderate irritantRabbit - 100 Percent-
Product/ingredient nameResult Score Exposure Observation
Sensitization
Not available.
Species
Information on the likely
routes of exposure
Inhalation :Harmful if inhaled. May cause respiratory irritation.
No known significant effects or critical hazards.:Ingestion
Skin contact :Causes skin irritation.
Causes serious eye irritation.:Eye contact
Specific target organ toxicity (single exposure)
Specific target organ toxicity (repeated exposure)
styrene Category 3 Not applicable.Respiratory tract
irritation
Name Category
Name Category
styrene Category 1 Inhalation hearing organs
Aspiration hazard
Name Result
styrene ASPIRATION HAZARD - Category 1
Route of
exposure
Target organs
Route of
exposure
Target organs
Information on toxicological effects
:Not available.
Potential acute health effects
Date of issue/Date of revision :9/30/2018Date of previous issue :No previous validationVersion:0.01 7/12
CLEAR CASTING RESIN Mexico SIL95BA-41
SECTION 11: Toxicological information
Not available.
Causes damage to organs through prolonged or repeated exposure.General :
No known significant effects or critical hazards.Carcinogenicity :
No known significant effects or critical hazards.Mutagenicity :
No known significant effects or critical hazards.Teratogenicity :
Developmental effects :No known significant effects or critical hazards.
Fertility effects :No known significant effects or critical hazards.
Symptoms related to the physical, chemical and toxicological characteristics
Skin contact
Ingestion
Inhalation Adverse symptoms may include the following:
respiratory tract irritation
coughing
No specific data.
Adverse symptoms may include the following:
irritation
redness
:
:
:
Eye contact :Adverse symptoms may include the following:
pain or irritation
watering
redness
Potential chronic health effects
Delayed and immediate effects and also chronic effects from short and long term exposure
Numerical measures of toxicity
Oral 7163 mg/kg
Inhalation (gases) 7487.4 ppm
Inhalation (vapors) 31.9 mg/l
Route ATE value
Acute toxicity estimates
Potential immediate
effects
:Not available.
Short term exposure
Potential delayed effects:Not available.
Potential immediate
effects
:Not available.
Long term exposure
Potential delayed effects:Not available.
SECTION 12: Ecological information
Toxicity
styrene Acute EC50 1400 g/l Fresh water Algae - Pseudokirchneriella
subcapitata
72 hours
Acute EC50 720 g/l Fresh water Algae - Pseudokirchneriella
subcapitata
96 hours
Acute EC50 4700 g/l Fresh water Daphnia - Daphnia magna 48 hours
Acute LC50 52 mg/l Marine water Crustaceans - Artemia salina48 hours
Acute LC50 4020 g/l Fresh water Fish - Pimephales promelas 96 hours
Chronic NOEC 63 g/l Fresh water Algae - Pseudokirchneriella 96 hours
Product/ingredient name SpeciesResult Exposure
Date of issue/Date of revision :9/30/2018Date of previous issue :No previous validationVersion:0.01 8/12
CLEAR CASTING RESIN Mexico SIL95BA-41
SECTION 12: Ecological information
LogPow BCF Potential
Bioaccumulative potential
Other adverse effects :No known significant effects or critical hazards.
Product/ingredient name
styrene 0.35 13.49 low
Product/ingredient name Aquatic half-life Photolysis Biodegradability
styrene - - Readily
subcapitata
Persistence and degradability
styrene OECD 70 % - Readily - 28 days - -
Product/ingredient name Test DoseResult Inoculum
Soil/water partition
coefficient (KOC)
:Not available.
Mobility in soil
SECTION 13: Disposal considerations
The generation of waste should be avoided or minimized wherever possible.
Disposal of this product, solutions and any by-products should at all times comply
with the requirements of environmental protection and waste disposal legislation
and any regional local authority requirements. Dispose of surplus and non-
recyclable products via a licensed waste disposal contractor. Waste should not be
disposed of untreated to the sewer unless fully compliant with the requirements of
all authorities with jurisdiction. Waste packaging should be recycled. Incineration or
landfill should only be considered when recycling is not feasible. This material and
its container must be disposed of in a safe way. Care should be taken when
handling emptied containers that have not been cleaned or rinsed out. Empty
containers or liners may retain some product residues. Vapor from product residues
may create a highly flammable or explosive atmosphere inside the container. Do
not cut, weld or grind used containers unless they have been cleaned thoroughly
internally. Avoid dispersal of spilled material and runoff and contact with soil,
waterways, drains and sewers.
:Disposal methods
SECTION 14: Transport information
RESIN
SOLUTION
3
III
RESIN
SOLUTION
3
III
RESIN
SOLUTION
UN1866
3
III
UN1866 UN1866
DOT
Classification
IMDG IATA
UN number
UN proper
shipping name
Transport
hazard class(es)
Packing group
Additional information
Environmental
hazards
No. No. No.
TDG
Classification
UN1866
RESIN
SOLUTION
3
III
No.
ADR/RID
UN1866
RESIN
SOLUTION
3
III
No.
Mexico
Classification
UN1866
RESIN
SOLUTION
3
III
No.
Date of issue/Date of revision :9/30/2018Date of previous issue :No previous validationVersion:0.01 9/12
CLEAR CASTING RESIN Mexico SIL95BA-41
SECTION 14: Transport information
Special precautions for user
Transport in bulk according
to Annex II of MARPOL and
the IBC Code
Transport within user s premises: always transport in closed containers that are
upright and secure. Ensure that persons transporting the product know what to do in
the event of an accident or spillage.
:Not available.
:
Reportable quantity 2703 lbs / 1227.1 kg [294.71 gal / 1115.6 L]. Package sizes
shipped in quantities less than the product reportable quantity are not subject to the
RQ (reportable quantity) transportation requirements.
Product classified as per the following sections of the Transportation of Dangerous
Goods Regulations: 2.18-2.19 (Class 3).
Tunnel code (D/E)
DOT Classification
TDG Classification
ADR/RID
:
:
:
SECTION 15: Regulatory information
International regulations
Montreal Protocol (Annexes A, B, C, E)
Not listed.
Stockholm Convention on Persistent Organic Pollutants
Not listed.
Rotterdam Convention on Prior Informed Consent (PIC)
Not listed.
Chemical Weapon Convention List Schedules I, II & III Chemicals
Not listed.
UNECE Aarhus Protocol on POPs and Heavy Metals
Not listed.
Inventory list
Australia :Not determined.
Canada :At least one component is not listed in DSL but all such components are listed in
NDSL.
China :Not determined.
Europe :Not determined.
Japan :Japan inventory (ENCS): Not determined.
Japan inventory (ISHL): Not determined.
Malaysia :Not determined.
National Fire Protection Association (U.S.A.)
1
3
2
Health
Special
Instability/Reactivity
Flammability
Reprinted with permission from NFPA 704-2001, Identification of the Hazards of Materials for Emergency
Response Copyright 1997, National Fire Protection Association, Quincy, MA 02269. This reprinted material
is not the complete and official position of the National Fire Protection Association, on the referenced
subject which is represented only by the standard in its entirety.
Copyright 2001, National Fire Protection Association, Quincy, MA 02269. This warning system is intended
to be interpreted and applied only by properly trained individuals to identify fire, health and reactivity
hazards of chemicals. The user is referred to certain limited number of chemicals with recommended
classifications in NFPA 49 and NFPA 325, which would be used as a guideline only. Whether the chemicals
are classified by NFPA or not, anyone using the 704 systems to classify chemicals does so at their own risk.
Date of issue/Date of revision :9/30/2018Date of previous issue :No previous validationVersion:0.0110/12
CLEAR CASTING RESIN Mexico SIL95BA-41
SECTION 15: Regulatory information
Republic of Korea :Not determined.
New Zealand :Not determined.
Philippines :Not determined.
Taiwan :Not determined.
United States :All components are listed or exempted.
Turkey :Not determined.
Thailand :Not determined.
Viet Nam :Not determined.
SECTION 16: Other information
9/30/2018
History
Date of printing
Date of issue/Date of
revision
Version
Prepared by
Notice to reader
Date of previous issue
:
:
:
:
:
Indicates information that has changed from previously issued version.
References :
Key to abbreviations :ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships,
1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution)
UN = United Nations
9/30/2018
No previous validation
0.01
Procedure used to derive the classification
Classification Justification
FLAMMABLE LIQUIDS - Category 3 On basis of test data
ACUTE TOXICITY (inhalation) - Category 4 Calculation method
SKIN IRRITATION - Category 2 Calculation method
EYE IRRITATION - Category 2A Calculation method
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Respiratory tract
irritation) - Category 3
Calculation method
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) (hearing organs)
- Category 1
Calculation method
Hazardous Material Information System (U.S.A.)
2
3
1
*
Health
Flammability
Physical hazards
Caution: HMIS ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4
representing significant hazards or risks. HMIS ratings are to be used with a fully implemented HMIS
program. HMIS is a registered trademark and service mark of the American Coatings Association, Inc.
The customer is responsible for determining the PPE code for this material. For more information on HMIS
Personal Protective Equipment (PPE) codes, consult the HMIS Implementation Manual.
iasafety@ip-corporation.com
NOM-018-STPS-2015
Date of issue/Date of revision :9/30/2018Date of previous issue :No previous validationVersion:0.0111/12
CLEAR CASTING RESIN Mexico SIL95BA-41
SECTION 16: Other information
The information, which is based on the current knowledge of the chemical substance or mixture and applies
to appropriate safety precautions for the product, is deemed correct but is not exhaustive and will be used
only as a guide.
Date of issue/Date of revision :9/30/2018Date of previous issue :No previous validationVersion:0.0112/12