MSDS
Icing Lite-26043.doc
Print Date: 10/14/2013
Page 1 of 5
SECTION 1 Chemical Product and Company Identification
QUEST AUTOMOTIVE PRODUCTS For Chemical Emergency:
600 Nova Drive SE CHEMTREC: 1-800-424-9300
Massillon, OH 44646
PH 330-830-6000 – FAX 330-830-6005
PRODUCT NAME: U.S. Chemical & Plastics Icing Lite
PRODUCT CODE: (26043), 26012
SYNONYM/CROSS REFERENCE: Purable/Brushable Polyester Finishing Putty
SCHEDULE B NUMBER: 3014.10.0090
SECTION 2 Hazard Identification
OVEREXPOSURE EFFECTS:
ACUTE EFFECTS:
EYES: Contact with eyes can cause irritation, redness, tearing, blurred vision, and/or swelling.
SKIN: Contact with skin can cause irritation, (minor itching, burning and/or redness), Dermatitis,
defatting may be readily absorbed through the skin.
INHALATION: Inhalation of vapors can cause nasal and respiratory irritation, dizziness, weakness,
fatigue, nausea, headache, possible unconsciousness and/or asphyxiation. Aspiration of material into lungs
may result in chemical pneumonitis which can be fatal.
INGESTION: Ingestion can cause gastrointestinal irritation, nausea, vomiting, diarrhea.
PRIMARY ROUTES OF EXPOSURE: skin, inhalation, eyes
SECTION 3 Composition, Information or Ingredients
INGREDIENTS WGT% CAS #
Styrene 20-30% 100-42-5
Non-fibrous Talc 10-20% 14807-96-6
Glass Beads 1-10% 65997-17-3
Titanium Dioxide 1-5% 13463-67-7
Calcium Carbonate 5-15% 1317-65-3, 471-34-1
SECTION 4 First Aid Measures
INHALATION: If inhaled, remove victim from exposure to a well-ventilated area. Make them comfortably
warm, but not hot. Use oxygen or artificial respiration as required. Consult a physician.
SKIN: For skin contact, wash promptly with soap and excess water.
EYES: For eye contact, flush promptly with excess water for at least fifteen minutes. Consult a physician.
INGESTION: If ingested, do not induce vomiting. Give victim a glass of water. Call a physician
immediately.
MSDS
Icing Lite-26043.doc
Print Date: 10/14/2013
Page 2 of 5
SECTION 5 Fire-Fighting Measures
FLASH POINT: 89 F/31.7 C Seta Flash Closed cup
LOWER FLAMMABLE LIMIT %: N/E
UPPER FLAMMABLE LIMIT %: N/E
FIRE EXTINGUISHING MEDIA: Carbon Dioxide, Dry Chemical, Foam
SPECIAL FIRE FIGHTING PROCEDURES: Fight like a fuel oil fire. Cool fire exposed containers with
water spray. Firefighter should wear OSHA/NIOSH approved self-contained breathing apparatus.
UNUSUAL FIRE AND EXPLOSION HAZARD: Closed containers exposed to high temperatures, such as
fire conditions may rupture.
SECTION 6 Accidental Release Measures
SPILLS, LEAK OR RELEASE: Ventilate area. Remove all possible sources of ignition. Avoid prolonged
breathing of vapor. Contain spill with inert absorbent.
SECTION 7 Handling and Storage
STORAGE AND HANDLING: Use with adequate ventilation. Avoid contact with eyes and skin. Avoid
breathing vapors. Do not store the product above 100 F/38 C. Do not flame, cut, braze weld or melt empty
containers. Keep the product away from heat, open flame, and other sources of ignition. Avoid contact with
strong acids, alkalis, and oxidizers.
SECTION 8 Exposure Controls and Personal Protection
INGREDIENTS CAS # TLV/PEL
Styrene 100-42-5 ACGIH: TLV 20 ppm (skin), STEL 40 ppm (skin)
OSHA: PEL 100 ppm, CPEL 200 ppm
See Health Hazard Information
Non-fibrous Talc 14807-96-6 ACGIH: TWA 2 mg/m
3
, OSHA: TLV 30 mppcf
Glass Beads 65997-17-3 ACGIH: TWA 10 mg/m
3
Titanium Dioxide 13463-67-7 ACGIH: TLV 10 mg/m
3
, OSHA: TWA 15 mg/m
3
Calcium Carbonate 1317-65-3 ACGIH: TLV 10 mg/m
3
471-34-1
RESPIRATORY PROTECTION: If component TLV limits are exceeded, use NIOSH/MSHA approved
respirator to remove vapors. Use an air-supplied respirator if necessary.
VENTILATION: Use adequate ventilation in volume and pattern to keep TLV/PEL below recommended
levels. Explosion-proof ventilation may be necessary.
PROTECTIVE GLOVES: To prevent prolonged exposure use rubber gloves; solvents may be absorbed
through the skin.
EYE PROTECTION: Safety Glasses or goggles with splash guards or side shields.
OTHER PROTECTIVE EQUIPMENT: Wear protective clothing as required to prevent skin contact.
MSDS
Icing Lite-26043.doc
Print Date: 10/14/2013
Page 3 of 5
SECTION 9 Physical and Chemical Properties
APPEARANCE: Yellow smooth paste
SPECIFIC GRAVITY: 0.96
VAPOR PRESSURE (mmHG): Heavier than air
BOILING POINT: N/Av
VAPOR DENSITY: Heavier than air
EVAPORATION RATE (Ethyl Ether = 1): Slower than Ethyl Ether
VOLATILES BY WEIGHT: 281 less exempts
SOLUBILITY IN WATER: None
VOC: Grams/liter = 245 less exempts; Grams/liter = 2.2 unconsumed VOC upon curing
SECTION 10 Stability and Reactivity
STABILITY: Stable
CONDITIONS TO AVOID: Open flames, sparks, heat, electrical and static discharge.
INCOMPATIBILITY MATERIALS TO AVOID: Strong acids, alkalis, oxidizers.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon Dioxide, Carbon Monoxide, and Carbon.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION 11 Toxicological Information
CHRONIC EFFECTS:
Overexposure to this material has apparently been known to cause the following effects in lab animals: Eye,
skin, lung, and central nervous system damage.
CARCINOGEN: YES __ NO X
TERATOGEN: YES __ NO X
MUTAGEN: YES __ NO X
STYRENE CARCINOGENICITY
Styrene is listed by IARC to be a possible carcinogen. Styrene studies have shown that Styrene causes cancer
in certain laboratory animals. However, there is insufficient evidence to conclude that Styrene is a human
carcinogen.
SECTION 12 Ecological Information
N/E
SECTION 13 Disposal Considerations
WASTE DISPOSAL: Dispose of in accordance with local, state, and federal regulations.
MSDS
Icing Lite-26043.doc
Print Date: 10/14/2013
Page 4 of 5
SECTION 14 Transport Information
For Ground Transport: In USA
Consumer Commodity ORM-D or Limited Quantity with inner containers less than 1 gallon
For containers larger than 1 gallon:
UN1866, Resin Solution, 3, PGIII and Cream Hardener shipped separately
Consumer Commodity ORM-D or Limited Quantity
For Air Transport:
Must be re-boxed to UN specified packaging in quantities of no more than 5 kg per fiberboard box
UN3269, Polyester Resin Kit, 3, PGIII
Packing Instruction 370
For Ocean Transport:
UN3269, Polyester Resin Kit, 3, PGIII, F/P 31.7 C
EMS # F-E, S-D, In limited quantity
SECTION 15 Regulatory Information
CALIFORNIA PROPOSITION 65:
Trace amounts of some chemicals known to the State of California to cause cancer, birth defects, or other
reproductive harm may be present in this product.
SECTION 313 SUPPLIER NOTIFICATION:
This product contains the following toxic chemicals subject to the reporting requirements of the Emergency
Planning and Community Right-To-Know Act of 1986 and 40 CFR 372:
CHEMICAL NAME CAS % BY WGT
Styrene 100-42-5 20-30%
This information must be included in all MSDS that are copied and distributed for this chemical.
SECTION 16 Other Information
HMIS RATING: Health 2 4 = Extreme
Fire 3 3 = High
Reactivity 1 2 = Moderate
1 = Slight
0 = Insignificant
Personal Protection – See Section VIII
MSDS
Icing Lite-26043.doc
Print Date: 10/14/2013
Page 5 of 5
ABBREVIATIONS
IARC = International Agency for Research on Cancer
ACGIH = American Conference of Governmental Industrial Hygienists
NIOSH = National Institute of Occupational Safety and Health
TLV = Threshold Limit Value
PEL = Permissible Emission Level
DOT = Department of Transportation
NTP = National Toxicology Program
N/AV = Not Available
N/AP = Not Applicable
N/E = Not Established
N/D = Not Determined
PREPARED BY: QUEST AUTOMOTIVE PRODUCTS
600 NOVA DRIVE SE
MASSILLON, OH 44646
TELEPHONE NBR: 330-830-6000
FAX NBR: 330-830-6005
DATE REVIEWED: October 14, 2013
DATE REVISED: NEW
REVISION: N/a
The information in the Material Safety Data Sheet has been compiled from our experience and from data
presented in various technical publications. It is the user s responsibility to determine the suitability of
this information for the adoption of the safety precautions as may be necessary. We reserve the right to
revise Material Safety Data Sheets from time to time as new technical information becomes available.
The user has the responsibility to contact the Company to make sure that the MSDS is the latest one
issued.