Royal Adhesives & Sealants, LLC 2001 W. Washington Street, South Bend, IN 46628 Phone: 800-999-GLUE Fax: 574-246-5425
This product is warranted to the original purchaser to meet published specifications, it any, and, in the absence of published specifications, to be merchantable quality. Such warranty may not be
assigned or otherwise transferred by purchaser. No other warranty, expressed or implied, of fitness for a particular purpose or any other thing is made. Purchaser’s exclusive remedy for breach of this
warranty shall be a refund of the price paid for the products by the purchaser. Except as stated above, Royal Adhesives & Sealants, LLC, shall not be liable for any defect in, or breach of obligation
relating to the defects in these products, regardless of the theory that may be asserted, including, without limitation, negligence, contract, absolute liability in tort or misrepresentation. If the purchaser
does not accept goods on these terms, they are to be returned at once, unopened.
TECHNICAL SALES BULLETIN___________________________ ___________________________
SOLIDSEAL
POLYURETHANE
ADHESIVE/SEALANT
SOLIDSEAL is a one component, fast cure, flexible, silicone free, rubber
based, dual purpose adhesive/sealant. It is a moisture cured, non sag system.
SOLIDSEAL provides a permanently elastic bond to most substrates.
DESIGNED TO BOND:
1. Various metals, including galvanized steel, stainless steel, cold rolled
steel, and aluminum
2. Wood, particle board and plywood
3. Glass, concrete, masonry and rubbers
4. Fiberglass and fiber reinforced plastics
5. Thermoset plastics such as polyurethane, polyester, epoxies
6. Thermoplastics, such as ABS, nylon, PVC
7. Skylights
8. Heating & air conditioning (HVAC) materials
FEATURES:
1. One component, ready to use, fast cure
2. Odorless and particularly low volume shrinkage
3. Silicone free; paintable with most paints
4. UV stable, heat and moisture resistant
5. Broad adhesion spectrum to most substrates
TYPICAL PROPERTIES:
(Specification ranges available upon request.)
Base: Polyurethane
Colors: White, gray & black
(custom colors available)
Viscosity: Paste extrusion grade
Weight/gallon: 10 pounds/gallon
Specific Gravity: 1.2
Temperature Range: -40 F to 190 F
Shelf Life: 12 months (in original container)
TYPICAL PHYSICAL CHARACTERISTICS:
(Specification ranges available upon request.)
Tensile Strength after 30 days at room temperature: 290 psi
Ultimate Elongation after 30 days at room temperature: 450%
Shore A Hardness after 30 days at room temperature: 50
UV Resistance: Very Good
Ozone Resistance: Excellent
Creep Resistance: Excellent
Sag Resistance: Excellent
PREPARATION OF SUBSTRATES:
Surfaces to be bonded should be cleaned of all dust, oils or other
contaminates. A solvent wipe is often adequate. Bonds to rigid surfaces are
usually improved by a solvent wipe followed with light abrasion (180 grit),
and solvent wiping to remove abrasive residue.
Dry surfaces thoroughly before applying adhesive
.
METHOD OF APPLICATION:
SOLIDSEAL can be applied by ordinary caulking guns or pressure
pumping equipment. Pumping equipment should be of the follower-plate type
and have a pump ratio of at least 65:1. Aro, Binks, DeVilbiss, Graco and
Lincoln all produce suitable equipment for handling this material. Consult
Royal representative or equipment supplier to ensure installation of proper
equipment (including moisture lock hoses and accessories) are in place before
start-up. Apply a bead of SOLIDSEAL to one surface at temperatures
above 40 F. Surface skin formation will occur in 40-60 minutes, depending
on ambient conditions. Initial set time is 4 hours, after which parts may be
handled.
Clamping, taping or use of mechanical fasteners to hold parts in place until
SOLIDSEAL develops strength is recommended. After 24 hours at room
temperature, the product is considered self-holding.
Strength build up is very fast in the early stages to give high holding power,
with continued strength build up over time.
SOLIDSEAL
POLYURETHANE
ADHESIVE/SEALANT (cont.)
TYPICAL LAP SHEAR STRENGTHS (PSI):
(Samples aged 30 days at room temperature; pulled at 2 inches per minute)
Aluminum to aluminum 208
Steel to steel 271
Galvanized steel to galvanized steel 126
Stainless Steel to Stainless Steel 211
CLEANER AND THINNER:
Toluene, Methyl Ethyl Ketone
PRECAUTIONARY DATA:
Store in dark and cool place. Avoid excessive heat. During storage, moisture
and water should be avoided. Reaction with moisture or water will cause
quality deterioration, but will not be hazardous. For industrial use only.
DISPOSAL INFORMATION:
Disposal should be made by incineration or in accordance with applicable
governmental regulations.
12/2/14 ISO 9001:2008 For reference only