Features and Benefits
Excellent Adhesion Properties
Excellent Bonding to Metals, Ceramics and Most Plastics
Excellent Chemical Resistance
Suitable for Cartridge and MMD Dispensing Equipment
Excellent Thermal Performance
100% Reactive
Room Temperature Cure
1:1 volume mix product for easy meter or static mix of application
MP5430
Technology / Base Epoxy
Type of Product Structural Adhesive
Components Two Component
Technical Data
Rheology Value Condition/Method
Curing Room Temperature (secondary thermal cure)
Appearance / Color Clear
Consistency Liquid
ASTM D257
Full Cure @ 66 C
Specific Gravity – Mix 1.16
Weight Mix Ratio 1 to 1
Uncured Material Characteristics
48.3 MPa (7000 psi) ASTM D638
Overlap Shear Strength
12,000 cPs at 25 C
80 Shore D
Elongation at Break 3 to 5 % ASTM D638
Aluminum, Acid Etched at 25 C15.9 MPa (2300 psi) ASTM D1002, 25 C 50% RH
Operating Temperature -40 C to 130 C (-40 F to 265 F)
Cured Electrical Properties
Dielectric Constant 4.5 at 25 C, 100Hz
Dielectric Strength 16.1 kV/mm ASTM D149
Volume Resistivity 8 E 14 ohm cm
Hardness
20 gram
20 gram
Handling Time
Specific Gravity – Part B 1.15
MP5430 is a two part unfilled epoxy adhesive designed for ceramics and most plastics. It cures to a tough semi-rigid materials, and is free
flowing in viscosity. It gives good resistance to water, salt spray, inorganic acids and bases, and most organic solvents. It was especially
formulated to a 1:1 volume mix ratio for use in either MMD equipment or side-by-side dual cartridges for easy dispensing. A handling cure
is normally achieved at room temperature within 20-30 minutes, with full cure in 24 hours. An elevated temperature cure schedule can be
used to reach final properties quickly.
Tensile Strength
Shelf Life 12 months unopened
ASTM D150
Volume Mix Ratio 1 to 1
Full Cure @ 23 C 24 hours
Pot Life
Gel Time
20 – 30 min at 25 C
13,000 cPs
ASTM D2240
Cured Mechanical Properties
12,500 cPs
Viscosity – Part B
Viscosity – Mixed
at 25 C
at 25 C
Viscosity – Part A
Specific Gravity – Part A 1.16
Technical Data Sheet
Safety and Disposal
See SDS for
Product should be stored in a cool dry place out of
direct sunlight. The shelf life is from date of
manufacture. Shelf life is based on the products being
stored properly at temperatures between 12 C and
25 C. Exposure to temperatures above 25 C will
reduce the shelf life. This product should not be
frozen.
See SDS for handling and clean-up information.
Surfaces to be bonded must be clean, dry and free of other
contaminants. Bring both components to room temperature
prior to mixing. Measure out specified amounts of parts A
and B and stir (without introducing bubbles) until
homogenous or use a static mixing nozzle. Apply the
uniform mixture to both surfaces. Allow to cure while being
held in place with light clamping.
Use Note
Storage
Handling and Clean-Up
General Instructions Specifications and Approvals
Connecting what matters.
www.hbfullerengineering.com
www.hbfuller.com
14 September 2018Date Modified:
H.B. Fuller Company, ASI
9411 Corsair Road
Frankfort, IL 60423
+1.815.464.5606 tel
Technical Data Sheet
NOTE TO USER: by ordering/receiving product you accept the H.B. Fuller General Terms and Conditions of Saleapplicable in the region.Please request a copy if you have not received
these.These Terms and Conditions contain disclaimers of implied warranties (including but not limited to disclaiming warranties of fitness for a particular purpose) and limits of liability. All other
terms are rejected. In any event, the total aggregate liability of H.B. Fuller for any claim or series of related claimshowever arising, in contract, tort (including negligence), breach of statutory
duty, misrepresentation, strict liability or otherwise,is limited to replacement of affected products or refund of the purchase price for affected products. H.B. Fuller shall not be liablefor loss of
profit, loss of margin, loss of contract, loss of business, loss of goodwill or any indirect or consequential lossesarising out of or in connection with product supply.
H.B. Fuller
www.hbfuller.com
H.B. Fuller Company, 2020
IMPORTANT:Information,specifications,proceduresandrecommendationsprovided( information )arebasedonourexperience,andwebelievethisinformationtobeaccurate.
Norepresentation,guaranteeorwarrantyismadeastotheaccuracyorcompletenessoftheinformationorthatuseoftheproductwillavoidlossesordamagesorgivedesired
results.Itispurchaser ssoleresponsibilitytotestanddeterminethesuitabilityofanyproductfortheintendeduse.Testsshouldberepeatedifmaterialsorconditionschangein
anyway.Noemployee,distributororagenthasanyrighttochangethesefactsandofferaguaranteeofperformance.
and aretrademarksofH.B.FullerCompanyoroneofitsaffiliatedentities.