March 1996
ATPRIME
2
SECONDARY BONDING AGENT
DESCRIPTION
ATPRIME
2 is a two-component urethane-based primer system developed to enhance
adhesion to FRP in secondary laminating operations, including bonding to non-air-
inhibited surfaces. The material is applied with a brush or roller to prepared surfaces.
Bonding is formed chemically.
ATPRIME
2 significantly improves interlaminar bond strength when used with Atlac
and Dion resins. It will also enhance bonding of FRP to concrete, bright carbon steel,
and thermoplastics such as PVC.
FEATURES BENEFITS
Moisture-activated curing system Virtually unaffected by temperature
fluctuations or substrate heat-sink effects
No catalyst required
Degree of cure unaffected by high
humidity or moisture-containing substrates
(concrete)
Versatile bonding characteristics Effective with FRP, steel, concrete,
thermoplastics, SMC, and other
substrates
Bonds to most vinyl ester and polyester
resins
Excellent tack retention Improves bonding up to 24 hours after
application
Reactive monomer system with no
methylene chloride
Superior bond strength
Environmentally friendly
Improved storage stability
ATPRIME 2
Page 2
TYPICAL LIQUID
PROPERTIES
1
@ 25
C
ATPRIME
2A
Flash Point, C ( F) . 218.3 (425)
Specific Gravity 1.23
Viscosity, cps . 180
Vapor Pressure, mm Hg <1x10
-4
Isocyanate Equivalent Weight . 133
NCO Content, % ... 31.5
Acidity, % as HCl .. 0.02
ATPRIME
2B
Flash Point, C ( F) 25.5 (78)
Shelf Life (minimum), months ... 6
Specific Gravity .. 1.01
Viscosity, cps 250
Color Pale yellow
APPLICATION
PROCEDURE
Prepare FRP surface to be bonded by lightly sanding, then cleaning with styrene
monomer. Chemically degraded sections of FRP structures should be ground down
to structurally sound laminate for subsequent repair procedure. More information is
available in the Reichhold Fabricators Handbook.
Steel should be sandblasted to white metal and primed promptly to avoid formation of
flash rust. Non-copper blast media must be used to avoid inhibition of ATPRIME
2
curing. Smooth, troweled concrete surfaces should also be sandblasted. Concrete
should be at least 10 days old before ATPRIME
2 is applied.
ATPRIME
2 components must be mixed before using. Blend 1 part (by weight)
ATPRIME
2A with 4 parts (by weight) ATPRIME
2B. No catalyst is necessary.
Allow mixture to stand 30 minutes before applying to the substrate. The pot life of blended ATPRIME
2 is approximately 12 hours at 80 F and 50% relative humidity.
Discard older material in accordance with applicable regulations.
The ATPRIME
2 system may be thixotroped to prevent drainage on vertical surfaces
and to improve adhesion to very porous substrates. Blend 3% hydrophilic fumed silica into ATPRIME
2B, followed by 0.2% Tween 20 or Tween 80 ( ICI Americas).
Apply the ATPRIME
2 mixture using a paintbrush, or a paint roller for larger surfaces.
For health and safety reasons, the mixture should never be sprayed. Allow primer to cure for a minimum of 2 hours at ambient temperature. Complete curing is evident
when the primer surface cannot be indented by a fingernail. The cure is moisture-
initiated, so cure time will vary with temperature and humidity conditions. If primer is
left more than 24 hours, re-application will be necessary to obtain full interlaminar
bond strength.
Apply polyester resin over the cured, primed surface, and then complete fiberglass lamination according to accepted industry practice.
To ensure maximum performance of the ATPRIME
2 bonding system, conduct
small-scale tests to determine the most suitable conditions. Specific substrates should also be evaluated before large-scale operations are conducted.
1
Properties listed in this bulletin are typical of those obtained in controlled laboratory tests and are provided as guidelines.
ATPRIME 2
Page 3
COVERAGE
One pound of blended ATPRIME
2 covers approximately 50-100 ft
2
of surface area.
One gallon of blended material covers approximately 420-800 ft
2
HANDLING
To ensure maximum performance of the ATPRIME
2 bonding system, the following
precautions should be taken:
Conduct small-scale tests to determine conditions most suitable for use of
ATPRIME
2.
ATPRIME
2 can be used on a wide variety of substrates. Specific applications
should be evaluated before large scale operations are conducted.
Pot life of mixture (ATPRIME
2A + ATPRIME
2B) is approximately 12 hours at
80 F with 50% relative humidity. Discard after this time in accordance with
applicable regulations.
Protect components from exposure to moisture; reseal opened containers and keep tightly sealed after use.
SAFETY
READ AND UNDERSTAND THE MATERIAL SAFETY DATA SHEET BEFORE
WORKING WITH THIS PRODUCT
It is the user s responsibility to understand the hazards associated with the use of ATPRIME
2. Obtain a copy of the material safety data sheet on this product prior to
use. MSDSs are available from your Reichhold sales representative. Such information should be requested from suppliers and understood prior to working with any chemicals.
ATPRIME
2 components can be irritating to skin and eyes. Wear cup-type chemical
safety goggles and impervious gloves to reduce chances of injury from contact with the liquid concentrate. Use clothing to protect other exposed skin areas. Contaminated clothing, gloves and footwear should be washed free of ATPRIME
2
before reuse.
ATPRIME
2 vapors and spray mist can be irritating. Prolonged or repeated
inhalation could result in an allergic reaction to its components. Inhalation of ATPRIME-2A vapors or spray mist can irritate the eyes, nose, and respiratory passages. Severe overexposure may lead to pulmonary edema. Local exhaust ventilation should be utilized to maintain permissible exposure levels of ATPRIME
2
in the workroom air. In absence of ventilating facilities, a MESA-NIOSH approved air- supplied respirator with full face piece should be used for respirator protection.
Spills should be soaked up promptly with an absorbent such as sawdust, vermiculite, or sand. Shovel material into an open-top container and soak for at least 24 hours with an aqueous solution containing 1-5% ammonia and 10% isopropanol. Close and
discard container. To facilitate clean-up in cold weather, utilize equal parts of
isopropanol and perchloroethylene. A MESA-NIOSH approved air-supplied respirator
or self-contained breathing apparatus should be used for protection during the clean-
up of major spills.
ATPRIME
2 has been used in many laboratory tests and field trials without problems
or discomfort to personnel. With proper precautions, no problems are anticipated; however, for the sake of safety, the recommended precautions must be strictly enforced.
ATPRIME 2
Page 4
FIRST AID
EMERGENCY INFORMATION : (800) 423-3003
POISON CONTROL CENTER : (213) 664-2121
EYES Rinse eyes immediately with plenty of water. Continue rinsing for at least 15 minutes.
INGESTION DO NOT INDUCE VOMITING. Immediately call a physician and refer him to a local poison
control center or (213) 664-2121 or (617) 232-2120.
INHALATION Seek fresh air immediately and obtain medical attention. If victim is unconscious,
administer artificial respiration and/or oxygen as needed, and seek medical attention
immediately.
SKIN Wash the contacted areas with soap and water.
TECHNICAL
SUPPORT
Reichhold s technical support facilities are staffed by people who have extensive
practical experience with polyesters and manufacturing techniques. Please do not
hesitate to request our assistance through your sales representative.
Copies of test methods used to determine reported properties are available through
your Reichhold sales representative.
Atprime, Atlac and Dion is a registered trademark of Reichhold, Inc.