Method State
Weight Cured
Volume Resin
COMBINED FEATURES Hardener
Property
Hardness
Compression Yield 12,200
Tensile Strength 6,320
Tensile Modulus 4.59E+05
Tensile Elongation
Flexural Strength 13,700
Flexural Modulus 4.57E+05
Lap Shear on 1018 Steel 1,920
Lap Shear on 2024T Aluminum 2,440
Tensile Adhesion to 1018 Steel 2,700
Tensile Adhesion to 2024T Aluminum 2,220
128(53)
2015 Gougeon Brothers, Inc.
ASTM D4541psi (MPa) (15)
Rev 4 / Dec 2015
1
Store PRO-SET Epoxy resins and hardeners at room temperature in sealed containers until shortly before use. As with
many high-performance epoxy resins, repeated exposure to low temperatures during storage may cause the resin to
crystallize. If this occurs, warm the resin to 125 F and stir to dissolve crystals. Hardeners may form carbamation when
exposed to CO
2 and moisture in the atmosphere for extended periods of time. Prevent carbamation by protecting hardeners
from exposure until immediately prior to processing.
Test specimens were neat epoxy (without fiber reinforcement).
Typical values, not to be construed as specification.
THERMAL PROPERTIES
Property Standard Units 77 F (25 C) x 2 wk
Heat Deflection TemperatureASTM D648 F ( C)
ASTM D1002psi (MPa) (17)
ASTM D4541psi (MPa) (19)
ASTM D790 psi (GPa) (3.15)
ASTM D1002psi (MPa) (13)
ASTM D638 % 6.2
ASTM D790psi (MPa) (94)
ASTM D638psi (MPa) (44)
ASTM D638 psi (GPa) (3.16)
ASTM D2240 Type D 85
ASTM D695psi (MPa) (84)
MECHANICAL PROPERTIES
lb/gal (g/cc)8.68 (1.04)
Standard Units 77 F (25 C) x 2 wk
Resin:HardenerResin:Hardener Units72 F (22 C)
TOUGHENED ADHESIVE EPOXY
2.24:1 100:44.6 lb/gal (g/cc)9.68 (1.16)
2.00:1 100:50.0 lb/gal (g/cc)9.68 (1.16)
Minimum Cure Temp ASTM D2196 F ( C)60 (16)
MIX RATIO DENSITY
100g Pot Life ASTM D2471minutes 31-39
Working Time (1/2″ bead)ASTM D2471minutes 45-55
72 F (22 C)
HANDLING PROPERTIES
Technical Data
Property Standard Units
Shear thinning resins and hardeners are
thixotropic gels. The mixture fills gaps and will not
sag on vertical surfaces. The material wets out the
substrate, making priming or pre-wetting
unnecessary on most surfaces, while ensuring a
good bond.
Medium cure speed hardener provides
approximately 50 minutes of working time at 72 F
(22 C).
Room temperature cure properties suitable for
many composite components and structures.
High performance pre-thickened, two-part epoxy
adhesive delivers toughness and superior peel
strength for heavily loaded applications and
difficult to bond substrates including pre-preg,
SMC, metals and most plastics. Also for
secondary bonding of laminated composites, steel,
aluminum, cast iron, concrete, stone, and most
wood species. PRO-SET Adhesives bonds these
material in any combination.
Coverage one cartridge set dispenses
approximately 47′ of 1/4″ bead, or 17′ of 1/2″ bead
and will cover approximately 7 sq ft when spread
with a 1/8″ x 1/8″ notched spreader, or 12 sq ft
with a 1/16″ x 1/16″ notched spreader.
Shelf life is 18 months for resin and 18 months for
hardener when properly stored
1
.
ADV-175
ADV-276
0
20
40
60
80
100
32
72
112
152
192
77 F (22 C)
x 2 wk
100 F (38 C)
x 24 hours
140 F (60 C)
x 8 hours
180 F (82 C)
x 8 hours
250 F (121 C)
x 4 hours
250 F (121 C)
x 8 hours
Degrees Celsius (
C)
Degrees Farenheit (
F)
Post Cure Schedule
T
g DSC Onset 1
st
Heat
133 F
(56 C)
138 F
(59 C)
158 F
(70 C)
162 F
(72 C)
169 F
(76 C)
171 F
(77 C)
T
g Ultimate