Property Standard Units 77 F (25 C)85 F (29 C)
150g Pot Life ASTM D2471minutes 263-323 192-236
500g Pot Life ASTM D2471minutes 211-259 138-170
Viscosity MixedASTM D2196 cP 1508 1046
Viscosity (resin)ASTM D2196 cP
Viscosity (hardener)ASTM D2196 cP
COMBINED FEATURES Method Resin:Hardener
Weight 3.5:1
Weight Range 3.75:1 3.30:1
Volume 3.00:1
Volume Range 3.14:1 2.75:1
State Units 72 F (22 C)
Cured lb/gal (g/cc)9.45 (1.13)
Resin lb/gal (g/cc)9.69 (1.16)
Hardener lb/gal (g/cc)7.86 (0.94)
2018 Gougeon Brothers, Inc.
HANDLING PROPERTIES
Technical Data
72 F (22 C)
358-438
276-338
1885
6300
121
LAMINATING EPOXY MIX RATIO
Resin:Hardener
100:28.6
100:26.6 100:30.3
100:31.9 100:36.3
100:33.3
DENSITY
Rev 3 / Dec 2015
Test specimens were neat epoxy (without fiber reinforcement).
Typical values, not to be construed as specification.
VISCOSITY VS TEMPERATURE
High temperature, high performance epoxy
formulation for synthetic composite mold and
tooling manufacture.
T
g as high as 350 F (176 C) with proper post
cure providing excellent temperature stability
and great part cosmetics.
Medium viscosity for wet out of synthetic
composite fabrics; especially effective with
carbon fiber.
Extra slow cure speed hardener provides 8
to 10 hours of working time at 77 F (25 C). A
typical laminate will be gelled in 14 to 20
hours at room temperature.
Optimized for hand wet out and machine
impregnation in contact molding, wet vacuum
bagging and Light RTM applications.
Elevated temperature cure is required;
thermal and mechanical properties suitable
for composite components and high
temperature tooling and molds.
Quality-control tinting is available at no extra
charge; simply add “QC” after the product
code on your order.
Shelf life is 3 years for resin and 18 months
for hardener when properly stored
3
.
0
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
50 60 70 80 90 100 110 120 130
Viscosity (cP)
Temperature ( F)
LAM-151-HT
LAM-251-HT
Hardness ASTM D2240Type D
Compression Yield ASTM D695psi (MPa)
Tensile Strength ASTM D638psi (MPa)
Tensile Modulus ASTM D638psi (GPa)
Tensile Elongation ASTM D638 %
Flexural Strength ASTM D790psi (MPa)
Flexural Modulus ASTM D790psi (GPa)
Tg DMA Peak Tan Delta ASTM E1640
1
F ( C)
Tg DMA Onset Storage ModulusASTM E1640
1
F ( C)
Tg DSC Onset 1st Heat ASTM E1356 F ( C)
Heat Deflection TemperatureASTM D648 F ( C)
Tg DSC Ultimate ASTM E1356 F ( C)
Rev 3 / Dec 2015
2018 Gougeon Brothers, Inc.
LAM-151-HT~LAM-251-HT
LAMINATING EPOXY
MECHANICAL PROPERTIES
89 90 87 86
Property Standard Units
200 F (93 C)
x 12 hrs
250 F (121 C)
x 8 hrs
140 F (60 C) x 2 hrs
+ 302 F (150 C)
x 4 hrs
87
16,600(114) 16,700(115) 16,300(112) 13,500(93) 13,500(93)
12,500(86) 10,800(74) 9,240(64) 9,690(67) 9,690(67)
4.75E+05(3.28)4.56E+05(3.14)4.14E+05(2.85)4.68E+05(3.23)4.28E+05(2.95)
5.5 3.9 3.8 4.2 5.6
(3.45)4.82E+05(3.32)
(105) 17,600(121) 18,100(125)
4.43E+05(3.05)4.10E+05(2.83)
21,400(148) 18,800(130) 15,200
THERMAL PROPERTIES
Property Standard Units
200 F (93 C)
x 12 hrs
3.84E+05(2.65)5.01E+05
250 F (121 C)
x 8 hrs
140 F (60 C) x 2 hrs
+ 302 F (150 C)
x 4 hrs
281 (138) 303 (151) 357 (181) 193 (90) 195 (91)
346 (175)
1
1 Hz, 3 C per minute.
2
Additional post cure may be required; contact Technical Department for details.
3
Store PRO-SET Epoxy resins and hardeners at room temperature in sealed containers until shortly before
use. As with many high-performance epoxy resins, repeated exposure to low temperatures during storage
may cause the resin to crystallize. If this occurs, warm the resin to 125 F and stir to dissolve crystals.
Hardeners may form carbamation when exposed to CO
2 and moisture in the atmosphere for extended periods
of time. Prevent carbamation by protecting hardeners from exposure until immediately prior to processing.
172 (78)
251 (122) 282 (139) 324 (162) 153 (67) 173 (78)
250 (121) 286 (141) 328 (164) 170 (77) 190 (88)
252 (122) 277 (136) 339 (171) 157 (69)