by | Sep 27, 2025
INDEX
CR4062
CR4062CG
CR4062CP
CR4062CQ
CR4062G
CR4062P
CR4062Q
CLEARMARINEGEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
Date of issue:10/13/2014 Revision date: Supersedes:
10/13/2014 EN(English US) Page 1
SECTION 1:Identification of the substance/mixture and of the company/undertaking
1.1. Product identifier
Product form :Mixture liquidresin
Trade name :ClearMarineGelCoat
CAS No :Mixture
Product code :CR4062CP, CR4062CQ, CR4062CG
Formula :NA
1.2. Relevant identified uses of the substance or mixture and uses advised against
Use of the substance/mixture :PRODUCTION GEL COAT
1.3. Details of the supplier of the safety data sheet
Composite Resources is supplied by Revchem Composites. 2720 South Willow Ave., Bloomington, CA 923161-800-281-4975
1.4. Emergency telephone number
Emergency number :800.424.9300
CHEMTREC: 1-800-424-9300
SECTION 2:Hazards identification
2.1. Classification of the substance or mixture
Classification (GHS-US)
Flam. Liq. 3 H226
Skin Irrit. 2 H315
Eye Irrit. 2A H319
Carc. Not classified
2.2. Label elements
GHS-US labeling
Hazard pictograms (GHS-US) :
GHS02 GHS07
Signal word (GHS-US) :Warning
Hazard statements (GHS-US) :H226-Flammable liquid and vapor
H315-Causes skin irritation
H319-Causes serious eye irritation
Precautionary statements (GHS-US) :P210-Keep away from heat, hot surfaces, open flames, sparks.-No smoking
P233-Keep container tightly closed
P240-Ground/bond container and receiving equipment
P241-Useexplosion-proof electrical, lighting, ventilating equipment
P242-Use only non-sparking tools
P243-Take precautionary measures against static discharge
P264-Wash EXPOSED AREA. thoroughly after handling
P280-Wear eye protection, protective clothing,protective gloves
P302+P352-IF ON SKIN: Wash with plenty of soap and water
P303+P361+P353-IF ON SKIN (or hair): Remove/Take off immediately all contaminated
clothing. Rinse skin with water/shower
P305+P351+P338-If in eyes: Rinse cautiously with waterfor several minutes. Remove contact
lenses, if present and easy to do. Continue rinsing
P321-Specific treatment (see SEEK MEDICAL AID. on this label)
P332+P313-If skin irritation occurs: Get medical advice/attention
P337+P313-If eye irritation persists: Get medical advice/attention
P362-Take off contaminated clothing and wash before reuse
P370+P378-In case of fire: Use carbon dioxide (CO2), dry chemical powder, foam to
extinguish
P403+P235-Store in a well-ventilated place. Keep cool
P501-Dispose of contents/container to LOCAL, STATE, AND NATIONAL REGULATIONS.
CLEARMARINEGEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 2/9
2.3. Other hazards
No additional information available
2.4. Unknown acute toxicity (GHS-US)
No data available
SECTION 3:Composition/information on ingredients
3.1. Substance
Not applicable
Full text of H-phrases: see section 16
3.2. Mixture
Name Product identifier % Classification (GHS-US)
Unsaturated Polyester Resin (CAS No)TRADE SECRET <= 55 Not classified
styrene, inhibited (CAS No)100-42-5 <= 43 Flam. Liq. 3, H226
Acute Tox. 4 (Inhalation:vapour),
H332
Skin Irrit. 2, H315
Eye Irrit. 2A, H319
Carc. 2, H351
cobalt(II) 2-ethylhexanoate (CAS No)136-52-7 <= 0.5 Carc. 2, H351
SECTION 4:First aid measures
4.1. Description of first aid measures
First-aid measures general :Never give anything by mouth to an unconscious person. If you feel unwell, seek medical advice
(show the label where possible).
First-aid measures after inhalation :Assure fresh air breathing. Allow the victim to rest. Remove to fresh air and keep at rest in a
position comfortable for breathing. Call a POISON CENTER/doctor/physician if you feel unwell.
First-aid measures after skin contact :Rinse skin with water/shower. Remove/Take off immediately all contaminated clothing. Wash
with plenty of soap and water. Wash contaminated clothing before reuse. If skin irritation occurs:
wash throughly for five minutes. seek medical attention. Get medical advice/attention. Specific
treatment (see seek medical attention. on this label).
First-aid measures after eye contact :Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to
do. Continue rinsing. If eye irritation persists: SEEK IMMEDIATE MEDICAL ATTENTION. Get
medical advice/attention.
First-aid measures after ingestion :Rinse mouth. Do NOT induce vomiting. Obtain emergency medical attention.
4.2. Most important symptoms and effects, both acute and delayed
Symptoms/injuries :May cause genetic defects (avoid skin contact and inhalation.). May cause cancer (avoid skin
contact and inhalation.).
Symptoms/injuries after inhalation :Danger of serious damage to health by prolonged exposure through inhalation. Harmful if
inhaled.
Symptoms/injuries after skin contact :Causes skin irritation.
Symptoms/injuries after eye contact :Causes serious eye irritation.
4.3. Indication of any immediate medical attention and special treatment needed
No additional information available
SECTION 5:Firefighting measures
5.1. Extinguishing media
suitable extinguishing media :Foam. Dry powder. Carbon dioxide. Water spray. Sand.
Unsuitable extinguishing media :Do not use a heavy water stream.
5.2. Special hazards arising from the substance or mixture
Fire hazard :Highly flammable liquid and vapor.
Explosion hazard :May form flammable/explosive vapor-air mixture.
Reactivity :No reactivity hazard other than the effects described in sub-sections below.
5.3. Advice for firefighters
Firefighting instructions :Use water spray or fog for cooling exposed containers. Exercise caution whenfighting any
chemical fire. Avoid (reject) fire-fighting water to enter environment.
Protection during firefighting :Do not enter fire area without proper protective equipment, including respiratory protection.
CLEARMARINEGEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 3/9
SECTION 6:Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
General measures :Remove ignition sources. Use special care to avoid static electric charges. No naked lights. No
smoking.
6.1.1.For non-emergency personnel
Protective equipment :Gloves. Protective goggles. Protective clothing.
Emergency procedures :Evacuate unnecessary personnel.
6.1.2.For emergency responders
Protective equipment :Equip cleanup crew with proper protection.
Emergency procedures :Ventilate area.
6.2. Environmental precautions
Prevent entry to sewers and public waters. Notify authorities if liquid enters sewers or public waters.
6.3. Methods and material for containment and cleaning up
For containment :Dam up the liquid spill. Contain released substance, pump into suitable containers.
Methods for cleaning up :Soak up spills with inert solids, such as clay or diatomaceous earth as soon as possible. Collect
spillage. Store away from other materials.
6.4. Reference to other sections
See Heading 8. Exposure controls and personal protection.
SECTION 7:Handling and storage
7.1. Precautions for safe handling
Additional hazards when processed :Handle empty containers with care because residual vapors are flammable.
Precautions for safe handling :Wash hands and other exposed areas with mild soap and water before eat, drink or smoke and
when leaving work. Provide good ventilation in process area to prevent formation of vapor. No
naked lights. No smoking. Use only non-sparking tools. Use only outdoors or in a well-ventilated
area. Avoid breathing DUST, FUMES, MIST, OR VAPORS. Obtain special instructions before
use. Do not handle until all safety precautions have been read and understood. Eliminate all
ignition sources if safe to do so.
Hygiene measures :Wash HANDS thoroughly after handling.
7.2. Conditions for safe storage, including any incompatibilities
Technical measures :Proper grounding procedures to avoid static electricity should be followed. Ground/bond
container and receiving equipment. Use explosion-proof electrical, ventilating and lighting
equipment. equipment.
Storage conditions :Keep only in the original container in a cool, well ventilated place away from : HEAT SPARKS
OR OPEN FLAMES. Keep in fireproof place. Keep container tightly closed.
Incompatible products :Strong bases. strong acids.
Incompatible materials :Sources of ignition. Direct sunlight. Heat sources.
7.3. Specific end use(s)
No additional information available
SECTION 8:Exposure controls/personal protection
8.1. Control parameters
styrene, inhibited (100-42-5)
USA ACGIH ACGIH TWA (ppm) 20 ppm
USA ACGIH ACGIH STEL (ppm) 40 ppm
8.2. Exposure controls
Appropriate engineering controls :Ensure exposure is below occupational exposure limits (where available).
Personal protective equipment :Avoid all unnecessary exposure.
Hand protection :Wear protective gloves.
Eye protection :Chemical goggles or safety glasses.
Skin and body protection :Wear suitable protective clothing.
Respiratory protection :Wear approved mask.
Other information :When using, do not eat, drink or smoke.
CLEARMARINEGEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 4/9
SECTION 9:Physical and chemical properties
9.1. Information on basic physical and chemical properties
Physical state :Liquid
Color :Clear
Odor :Characteristic
Odor threshold :No data available
pH :No data available
Relative evaporation rate (butyl acetate=1):No data available
Melting point :No data available
Freezing point :No data available
Boiling point : 64 C
Flash point :30-34 C
Auto-ignition temperature :No data available
Decomposition temperature :No data available
Flammability (solid, gas) :No data available
Vapor pressure :No data available
Relative vapor density at 20 C :No data available
Relative density : 1.1
Solubility :No data available
Log Pow :No data available
Log Kow :No data available
Viscosity, kinematic :No data available
Viscosity, dynamic :No data available
Explosive properties :No data available
Oxidizing properties :No data available
Explosive limits :No data available
9.2. Other information
No additional information available
SECTION 10:Stability and reactivity
10.1.Reactivity
No reactivity hazard other than theeffects described in sub-sections below.
10.2.Chemical stability
Polymerization can result in formation of solid deposits, even in vapour space. Not established. Highly flammable liquid andvapor. May form
flammable/explosive vapor-air mixture.
10.3.Possibility of hazardous reactions
Not established.
10.4.Conditions to avoid
Direct sunlight. Extremely high or low temperatures. Open flame.
10.5.Incompatible materials
strong acids. Strong bases.
10.6.Hazardous decomposition products
fume. Carbon monoxide. Carbon dioxide. May release flammable gases.
SECTION 11:Toxicological information
11.1.Information on toxicological effects
Acute toxicity :Not classified
ULTRA CLEAR GEL COAT (f )mixture
ATE CLP (dust, mist) 1.500 mg/l/4h
styrene, inhibited (100-42-5)
LD50 oral rat 5000 mg/kg (>6000 mg/kg bodyweight; Rat; Rat)
CLEARMARINEGEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 5/9
styrene, inhibited (100-42-5)
LD50 dermal rat 2820 mg/kg (>2000 mg/kg bodyweight; Rat; Rat; Experimental value)
LD50 dermal rabbit 5010 mg/kg (Rabbit)
LC50 inhalation rat (mg/l) 12 mg/l/4h (Rat)
LC50 inhalation rat (ppm) 2770 ppm/4h (Rat)
ATE CLP (oral) 5000.000 mg/kg
ATE CLP (dermal) 5010.000 mg/kg
Skin corrosion/irritation :Causes skin irritation.
Serious eye damage/irritation :Causes serious eye irritation.
Respiratory or skin sensitization :Not classified
Germ cell mutagenicity :Not classified
Carcinogenicity :Not classified.
styrene, inhibited (100-42-5)
IARC group 2B-Possibly Carcinogenic to Humans
cobalt(II) 2-ethylhexanoate (136-52-7)
IARC group 2B-Possibly Carcinogenic toHumans
Reproductive toxicity :Not classified
Based on available data, the classification criteria are not met
Specific target organ toxicity (single exposure):Not classified
Specific target organ toxicity (repeated
exposure)
:Not classified
Based on available data, the classification criteria are not met
Aspiration hazard :Not classified
Based on available data, the classification criteria are not met
Potential Adverse human health effects and
symptoms
:Harmful if inhaled.
Symptoms/injuries after inhalation :Danger of serious damage to health by prolonged exposure through inhalation. Harmful if
inhaled.
Symptoms/injuries after skin contact :Causes skin irritation.
Symptoms/injuries after eye contact :Causes serious eye irritation.
SECTION 12:Ecological information
12.1.Toxicity
styrene, inhibited (100-42-5)
LC50 fish 1 25 mg/l (96 h; Lepomis macrochirus)
LC50 other aquatic organisms 1 10-100 mg/l (96 h)
EC50 Daphnia 1 23 mg/l (48 h; Daphnia magna; LOCOMOTOR EFFECT)
LC50 fish 2 32 mg/l (96 h; Pimephales promelas)
EC50 Daphnia 2 27 mg/l (24 h; Daphnia magna)
TLM fish 1 25.1 mg/l (96 h; Lepomis macrochirus; SOFT WATER)
TLM fish 2 46.4 mg/l (96 h; Pimephales promelas; SOFT WATER)
TLM other aquatic organisms 1 10-100,96 h
Threshold limit other aquatic organisms 110-100,96 h; Pseudomonas putida
Threshold limit other aquatic organisms 272 mg/l
Threshold limit algae 1 > 200 mg/l (192 h; Scenedesmus quadricauda; INHIBITORY)
Threshold limit algae 2 67 mg/l (Microcystis aeruginosa; INHIBITORY)
12.2.Persistence and degradability
ULTRA CLEAR GEL COAT (mixture)
Persistence and degradability Not established.
styrene, inhibited (100-42-5)
Persistence and degradability Readily biodegradable in water. Not readily biodegradable in water. Forming sediments in
water. Non degradable in the soil. Adsorbs into the soil. Photodegradation in the air. Not
established.
CLEARMARINEGEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 6/9
styrene, inhibited (100-42-5)
Chemical oxygen demand (COD) 2.80 g O /g substance
ThOD 3.07 g O /g substance
BOD (% of ThOD) 0.42 % ThOD
cobalt(II) 2-ethylhexanoate (136-52-7)
Persistence and degradability Biodegradability in water: no data available.
Unsaturated Polyester Resin (TRADE SECRET)
Persistence and degradability Not established.
12.3.Bioaccumulative potential
ULTRA CLEAR GEL COAT(mixture)
Bioaccumulative potential Not established.
styrene, inhibited (100-42-5)
BCF fish 1 12-77 (QSAR)
BCF fish 2 35.5 (Carassius auratus)
Log Pow 2.95-3.16 (Experimental value)
Bioaccumulative potential Low potential for bioaccumulation (BCF < 500). Not established.
cobalt(II) 2-ethylhexanoate (136-52-7)
Bioaccumulative potential No bioaccumulation data available.
Unsaturated Polyester Resin (TRADE SECRET)
Bioaccumulative potential Not established.
12.4.Mobility in soil
styrene, inhibited (100-42-5)
Surface tension 0.032 N/m (19 C)
12.5.Other adverse effects
Other information :Avoid release to the environment.
SECTION 13:Disposal considerations
13.1.Waste treatment methods
Waste disposal recommendations :Dispose in a safe manner in accordance with local/national regulations. Dispose of
contents/container to approved disposal site.
Additional information :Handle empty containers with care because residual vapors are flammable.
Ecology-waste materials :Avoid release to the environment.
SECTION 14:Transport information
In accordance with DOT
UN-No.(DOT) :UN1866
DOT Proper Shipping Name :RESIN SOLUTION
Department of Transportation (DOT) Hazard
Classes
:3-Class 3-Flammable and combustible liquid49 CFR 173.120
Hazard labels (DOT) :3-Flammable liquid
Packing group (DOT) :III-Minor Danger
Additional information
Other information :No supplementary information available.
ADR
Transport document description :UN 1866, 3, III, (D/E)
CLEARMARINEGEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 7/9
Packing group (ADR) :III
Class (ADR) :3-Flammable liquid
Hazard identification number (Kemler No.):33
Classification code (ADR) :F1
Danger labels (ADR) :3-Flammable liquids
Orange plates :
Tunnel restriction code :D/E
LQ :5L
Exceptedquantities (ADR) :E2
Transport by sea
UN-No. (IMDG) :1866
Proper Shipping Name (IMDG) :RESIN SOLUTION
Class (IMDG) :3-Flammable liquids
Packing group (IMDG) :III-substances presenting low danger
Air transport
UN-No.(IATA) :1866
Proper Shipping Name (IATA) :RESIN SOLUTION
Class (IATA) :3-Flammable Liquids
Packing group (IATA) :III-Minor Danger
SECTION 15:Regulatory information
15.1. US Federal regulations
styrene, inhibited (100-42-5)
RQ (Reportable quantity, section 304 of EPA's
List of Lists) :
1000 lb
SARA Section 311/312 Hazard Classes Immediate (acute) health hazard
Reactive hazard
Fire hazard
Delayed (chronic) health hazard
15.2. International regulations
CANADA
No additional information available
EU-Regulations
No additional information available
Classification according to Regulation (EC) No. 1272/2008 [CLP]
Flam. Liq. 2 H225
Acute Tox. 4 (Inhalation:dust,mist)H332
Skin Irrit. 2 H315
Eye Irrit. 2 H319
Muta. 1B H340
Carc. 1B H350
Full textof H-phrases: see section 16
CLEARMARINEGEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 8/9
Classification according to Directive 67/548/EEC or 1999/45/EC
Carc.Cat.2; R45
Muta.Cat.2; R46
F; R11
Xn; R20
Xi; R36/38
Full text of R-phrases: see section 16
15.2.2.National regulations
styrene, inhibited (100-42-5)
Listed on EPA's Hazardous Air Pollutants (HAPS)
15.3. US State regulations
styrene, inhibited (100-42-5)
U.S.-California-
Proposition 65-
Carcinogens List
U.S.-California-
Proposition 65-
Developmental Toxicity
U.S.-California-
Proposition65-
Reproductive Toxicity-
Female
U.S.-California-
Proposition 65-
Reproductive Toxicity-Male
No significance risk level
(NSRL)
styrene, inhibited (100-42-5)
U.S.-Massachusetts-Right To Know List
U.S.-New Jersey-Right to Know Hazardous Substance List
U.S.-Pennsylvania-RTK (Right to Know)-Environmental Hazard List
SECTION 16:Other information
Data sources :REGULATION (EC) No 1272/2008 OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 16 December 2008 on classification,labeling and packaging of substances and
mixtures, amending and repealing Directives 67/548/EEC and 1999/45/EC, and amending
Regulation (EC) No 1907/2006.
Other information :None.
Full text of H-phrases: see section 16:
------Acute Tox. 4 (Inhalation:vapour) Acute toxicity (inhalation:vapour) Category 4
------Carc. 2 Carcinogenicity Category 2
------Carc. Not classified Carcinogenicity Not classified
------Eye Irrit. 2A Serious eye damage/eye irritation Category 2A
------Flam. Liq. 3 Flammableliquids Category 3
------Skin Irrit. 2 Skin corrosion/irritation Category 2
------H226 Flammable liquid and vapor
------H315 Causes skin irritation
------H319 Causes serious eye irritation
------H332 Harmful if inhaled
------H351 Suspected ofcausing cancer
NFPA health hazard :2-Intense or continued exposure could cause temporary
incapacitation or possible residual injury unless prompt
medical attention is given.
NFPA fire hazard :3-Liquids and solids that can be ignited under almost all
ambient conditions.
NFPA reactivity :2-Normally unstable and readily undergo violent
decomposition but do not detonate. Also: may react
violently with water or may form potentially explosive
mixtures with water.
CLEARMARINEGEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 9/9
HMIS III Rating
Health :2Moderate Hazard-Temporary or minor injury may occur
Flammability :3 Serious Hazard
Physical :1 Slight Hazard
Personal Protection :H
SDS US (GHS HazCom 2012)
To the best of our knowledge this SDS is accurate. The the extent allowed by law, thisstatement is made in lieu of an other warranties, expressed or implied including but not limited to any implied
warranty of merchantability or fitness for a particular purpose and is in lieu of any other obligations or liability on the part of Dura Technoligies, Inc.
by | Sep 27, 2025
INDEX
CR4062
CR4062CG
CR4062CP
CR4062CQ
CR4062G
CR4062P
CR4062Q
CLEARMARINEGEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
Date of issue:10/13/2014 Revision date: Supersedes:
10/13/2014 EN(English US) Page 1
SECTION 1:Identification of the substance/mixture and of the company/undertaking
1.1. Product identifier
Product form :Mixture liquidresin
Trade name :ClearMarineGelCoat
CAS No :Mixture
Product code :CR4062CP, CR4062CQ, CR4062CG
Formula :NA
1.2. Relevant identified uses of the substance or mixture and uses advised against
Use of the substance/mixture :PRODUCTION GEL COAT
1.3. Details of the supplier of the safety data sheet
Composite Resources is supplied by Revchem Composites. 2720 South Willow Ave., Bloomington, CA 923161-800-281-4975
1.4. Emergency telephone number
Emergency number :800.424.9300
CHEMTREC: 1-800-424-9300
SECTION 2:Hazards identification
2.1. Classification of the substance or mixture
Classification (GHS-US)
Flam. Liq. 3 H226
Skin Irrit. 2 H315
Eye Irrit. 2A H319
Carc. Not classified
2.2. Label elements
GHS-US labeling
Hazard pictograms (GHS-US) :
GHS02 GHS07
Signal word (GHS-US) :Warning
Hazard statements (GHS-US) :H226-Flammable liquid and vapor
H315-Causes skin irritation
H319-Causes serious eye irritation
Precautionary statements (GHS-US) :P210-Keep away from heat, hot surfaces, open flames, sparks.-No smoking
P233-Keep container tightly closed
P240-Ground/bond container and receiving equipment
P241-Useexplosion-proof electrical, lighting, ventilating equipment
P242-Use only non-sparking tools
P243-Take precautionary measures against static discharge
P264-Wash EXPOSED AREA. thoroughly after handling
P280-Wear eye protection, protective clothing,protective gloves
P302+P352-IF ON SKIN: Wash with plenty of soap and water
P303+P361+P353-IF ON SKIN (or hair): Remove/Take off immediately all contaminated
clothing. Rinse skin with water/shower
P305+P351+P338-If in eyes: Rinse cautiously with waterfor several minutes. Remove contact
lenses, if present and easy to do. Continue rinsing
P321-Specific treatment (see SEEK MEDICAL AID. on this label)
P332+P313-If skin irritation occurs: Get medical advice/attention
P337+P313-If eye irritation persists: Get medical advice/attention
P362-Take off contaminated clothing and wash before reuse
P370+P378-In case of fire: Use carbon dioxide (CO2), dry chemical powder, foam to
extinguish
P403+P235-Store in a well-ventilated place. Keep cool
P501-Dispose of contents/container to LOCAL, STATE, AND NATIONAL REGULATIONS.
CLEARMARINEGEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 2/9
2.3. Other hazards
No additional information available
2.4. Unknown acute toxicity (GHS-US)
No data available
SECTION 3:Composition/information on ingredients
3.1. Substance
Not applicable
Full text of H-phrases: see section 16
3.2. Mixture
Name Product identifier % Classification (GHS-US)
Unsaturated Polyester Resin (CAS No)TRADE SECRET <= 55 Not classified
styrene, inhibited (CAS No)100-42-5 <= 43 Flam. Liq. 3, H226
Acute Tox. 4 (Inhalation:vapour),
H332
Skin Irrit. 2, H315
Eye Irrit. 2A, H319
Carc. 2, H351
cobalt(II) 2-ethylhexanoate (CAS No)136-52-7 <= 0.5 Carc. 2, H351
SECTION 4:First aid measures
4.1. Description of first aid measures
First-aid measures general :Never give anything by mouth to an unconscious person. If you feel unwell, seek medical advice
(show the label where possible).
First-aid measures after inhalation :Assure fresh air breathing. Allow the victim to rest. Remove to fresh air and keep at rest in a
position comfortable for breathing. Call a POISON CENTER/doctor/physician if you feel unwell.
First-aid measures after skin contact :Rinse skin with water/shower. Remove/Take off immediately all contaminated clothing. Wash
with plenty of soap and water. Wash contaminated clothing before reuse. If skin irritation occurs:
wash throughly for five minutes. seek medical attention. Get medical advice/attention. Specific
treatment (see seek medical attention. on this label).
First-aid measures after eye contact :Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to
do. Continue rinsing. If eye irritation persists: SEEK IMMEDIATE MEDICAL ATTENTION. Get
medical advice/attention.
First-aid measures after ingestion :Rinse mouth. Do NOT induce vomiting. Obtain emergency medical attention.
4.2. Most important symptoms and effects, both acute and delayed
Symptoms/injuries :May cause genetic defects (avoid skin contact and inhalation.). May cause cancer (avoid skin
contact and inhalation.).
Symptoms/injuries after inhalation :Danger of serious damage to health by prolonged exposure through inhalation. Harmful if
inhaled.
Symptoms/injuries after skin contact :Causes skin irritation.
Symptoms/injuries after eye contact :Causes serious eye irritation.
4.3. Indication of any immediate medical attention and special treatment needed
No additional information available
SECTION 5:Firefighting measures
5.1. Extinguishing media
suitable extinguishing media :Foam. Dry powder. Carbon dioxide. Water spray. Sand.
Unsuitable extinguishing media :Do not use a heavy water stream.
5.2. Special hazards arising from the substance or mixture
Fire hazard :Highly flammable liquid and vapor.
Explosion hazard :May form flammable/explosive vapor-air mixture.
Reactivity :No reactivity hazard other than the effects described in sub-sections below.
5.3. Advice for firefighters
Firefighting instructions :Use water spray or fog for cooling exposed containers. Exercise caution whenfighting any
chemical fire. Avoid (reject) fire-fighting water to enter environment.
Protection during firefighting :Do not enter fire area without proper protective equipment, including respiratory protection.
CLEARMARINEGEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 3/9
SECTION 6:Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
General measures :Remove ignition sources. Use special care to avoid static electric charges. No naked lights. No
smoking.
6.1.1.For non-emergency personnel
Protective equipment :Gloves. Protective goggles. Protective clothing.
Emergency procedures :Evacuate unnecessary personnel.
6.1.2.For emergency responders
Protective equipment :Equip cleanup crew with proper protection.
Emergency procedures :Ventilate area.
6.2. Environmental precautions
Prevent entry to sewers and public waters. Notify authorities if liquid enters sewers or public waters.
6.3. Methods and material for containment and cleaning up
For containment :Dam up the liquid spill. Contain released substance, pump into suitable containers.
Methods for cleaning up :Soak up spills with inert solids, such as clay or diatomaceous earth as soon as possible. Collect
spillage. Store away from other materials.
6.4. Reference to other sections
See Heading 8. Exposure controls and personal protection.
SECTION 7:Handling and storage
7.1. Precautions for safe handling
Additional hazards when processed :Handle empty containers with care because residual vapors are flammable.
Precautions for safe handling :Wash hands and other exposed areas with mild soap and water before eat, drink or smoke and
when leaving work. Provide good ventilation in process area to prevent formation of vapor. No
naked lights. No smoking. Use only non-sparking tools. Use only outdoors or in a well-ventilated
area. Avoid breathing DUST, FUMES, MIST, OR VAPORS. Obtain special instructions before
use. Do not handle until all safety precautions have been read and understood. Eliminate all
ignition sources if safe to do so.
Hygiene measures :Wash HANDS thoroughly after handling.
7.2. Conditions for safe storage, including any incompatibilities
Technical measures :Proper grounding procedures to avoid static electricity should be followed. Ground/bond
container and receiving equipment. Use explosion-proof electrical, ventilating and lighting
equipment. equipment.
Storage conditions :Keep only in the original container in a cool, well ventilated place away from : HEAT SPARKS
OR OPEN FLAMES. Keep in fireproof place. Keep container tightly closed.
Incompatible products :Strong bases. strong acids.
Incompatible materials :Sources of ignition. Direct sunlight. Heat sources.
7.3. Specific end use(s)
No additional information available
SECTION 8:Exposure controls/personal protection
8.1. Control parameters
styrene, inhibited (100-42-5)
USA ACGIH ACGIH TWA (ppm) 20 ppm
USA ACGIH ACGIH STEL (ppm) 40 ppm
8.2. Exposure controls
Appropriate engineering controls :Ensure exposure is below occupational exposure limits (where available).
Personal protective equipment :Avoid all unnecessary exposure.
Hand protection :Wear protective gloves.
Eye protection :Chemical goggles or safety glasses.
Skin and body protection :Wear suitable protective clothing.
Respiratory protection :Wear approved mask.
Other information :When using, do not eat, drink or smoke.
CLEARMARINEGEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 4/9
SECTION 9:Physical and chemical properties
9.1. Information on basic physical and chemical properties
Physical state :Liquid
Color :Clear
Odor :Characteristic
Odor threshold :No data available
pH :No data available
Relative evaporation rate (butyl acetate=1):No data available
Melting point :No data available
Freezing point :No data available
Boiling point : 64 C
Flash point :30-34 C
Auto-ignition temperature :No data available
Decomposition temperature :No data available
Flammability (solid, gas) :No data available
Vapor pressure :No data available
Relative vapor density at 20 C :No data available
Relative density : 1.1
Solubility :No data available
Log Pow :No data available
Log Kow :No data available
Viscosity, kinematic :No data available
Viscosity, dynamic :No data available
Explosive properties :No data available
Oxidizing properties :No data available
Explosive limits :No data available
9.2. Other information
No additional information available
SECTION 10:Stability and reactivity
10.1.Reactivity
No reactivity hazard other than theeffects described in sub-sections below.
10.2.Chemical stability
Polymerization can result in formation of solid deposits, even in vapour space. Not established. Highly flammable liquid andvapor. May form
flammable/explosive vapor-air mixture.
10.3.Possibility of hazardous reactions
Not established.
10.4.Conditions to avoid
Direct sunlight. Extremely high or low temperatures. Open flame.
10.5.Incompatible materials
strong acids. Strong bases.
10.6.Hazardous decomposition products
fume. Carbon monoxide. Carbon dioxide. May release flammable gases.
SECTION 11:Toxicological information
11.1.Information on toxicological effects
Acute toxicity :Not classified
ULTRA CLEAR GEL COAT (f )mixture
ATE CLP (dust, mist) 1.500 mg/l/4h
styrene, inhibited (100-42-5)
LD50 oral rat 5000 mg/kg (>6000 mg/kg bodyweight; Rat; Rat)
CLEARMARINEGEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 5/9
styrene, inhibited (100-42-5)
LD50 dermal rat 2820 mg/kg (>2000 mg/kg bodyweight; Rat; Rat; Experimental value)
LD50 dermal rabbit 5010 mg/kg (Rabbit)
LC50 inhalation rat (mg/l) 12 mg/l/4h (Rat)
LC50 inhalation rat (ppm) 2770 ppm/4h (Rat)
ATE CLP (oral) 5000.000 mg/kg
ATE CLP (dermal) 5010.000 mg/kg
Skin corrosion/irritation :Causes skin irritation.
Serious eye damage/irritation :Causes serious eye irritation.
Respiratory or skin sensitization :Not classified
Germ cell mutagenicity :Not classified
Carcinogenicity :Not classified.
styrene, inhibited (100-42-5)
IARC group 2B-Possibly Carcinogenic to Humans
cobalt(II) 2-ethylhexanoate (136-52-7)
IARC group 2B-Possibly Carcinogenic toHumans
Reproductive toxicity :Not classified
Based on available data, the classification criteria are not met
Specific target organ toxicity (single exposure):Not classified
Specific target organ toxicity (repeated
exposure)
:Not classified
Based on available data, the classification criteria are not met
Aspiration hazard :Not classified
Based on available data, the classification criteria are not met
Potential Adverse human health effects and
symptoms
:Harmful if inhaled.
Symptoms/injuries after inhalation :Danger of serious damage to health by prolonged exposure through inhalation. Harmful if
inhaled.
Symptoms/injuries after skin contact :Causes skin irritation.
Symptoms/injuries after eye contact :Causes serious eye irritation.
SECTION 12:Ecological information
12.1.Toxicity
styrene, inhibited (100-42-5)
LC50 fish 1 25 mg/l (96 h; Lepomis macrochirus)
LC50 other aquatic organisms 1 10-100 mg/l (96 h)
EC50 Daphnia 1 23 mg/l (48 h; Daphnia magna; LOCOMOTOR EFFECT)
LC50 fish 2 32 mg/l (96 h; Pimephales promelas)
EC50 Daphnia 2 27 mg/l (24 h; Daphnia magna)
TLM fish 1 25.1 mg/l (96 h; Lepomis macrochirus; SOFT WATER)
TLM fish 2 46.4 mg/l (96 h; Pimephales promelas; SOFT WATER)
TLM other aquatic organisms 1 10-100,96 h
Threshold limit other aquatic organisms 110-100,96 h; Pseudomonas putida
Threshold limit other aquatic organisms 272 mg/l
Threshold limit algae 1 > 200 mg/l (192 h; Scenedesmus quadricauda; INHIBITORY)
Threshold limit algae 2 67 mg/l (Microcystis aeruginosa; INHIBITORY)
12.2.Persistence and degradability
ULTRA CLEAR GEL COAT (mixture)
Persistence and degradability Not established.
styrene, inhibited (100-42-5)
Persistence and degradability Readily biodegradable in water. Not readily biodegradable in water. Forming sediments in
water. Non degradable in the soil. Adsorbs into the soil. Photodegradation in the air. Not
established.
CLEARMARINEGEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 6/9
styrene, inhibited (100-42-5)
Chemical oxygen demand (COD) 2.80 g O /g substance
ThOD 3.07 g O /g substance
BOD (% of ThOD) 0.42 % ThOD
cobalt(II) 2-ethylhexanoate (136-52-7)
Persistence and degradability Biodegradability in water: no data available.
Unsaturated Polyester Resin (TRADE SECRET)
Persistence and degradability Not established.
12.3.Bioaccumulative potential
ULTRA CLEAR GEL COAT(mixture)
Bioaccumulative potential Not established.
styrene, inhibited (100-42-5)
BCF fish 1 12-77 (QSAR)
BCF fish 2 35.5 (Carassius auratus)
Log Pow 2.95-3.16 (Experimental value)
Bioaccumulative potential Low potential for bioaccumulation (BCF < 500). Not established.
cobalt(II) 2-ethylhexanoate (136-52-7)
Bioaccumulative potential No bioaccumulation data available.
Unsaturated Polyester Resin (TRADE SECRET)
Bioaccumulative potential Not established.
12.4.Mobility in soil
styrene, inhibited (100-42-5)
Surface tension 0.032 N/m (19 C)
12.5.Other adverse effects
Other information :Avoid release to the environment.
SECTION 13:Disposal considerations
13.1.Waste treatment methods
Waste disposal recommendations :Dispose in a safe manner in accordance with local/national regulations. Dispose of
contents/container to approved disposal site.
Additional information :Handle empty containers with care because residual vapors are flammable.
Ecology-waste materials :Avoid release to the environment.
SECTION 14:Transport information
In accordance with DOT
UN-No.(DOT) :UN1866
DOT Proper Shipping Name :RESIN SOLUTION
Department of Transportation (DOT) Hazard
Classes
:3-Class 3-Flammable and combustible liquid49 CFR 173.120
Hazard labels (DOT) :3-Flammable liquid
Packing group (DOT) :III-Minor Danger
Additional information
Other information :No supplementary information available.
ADR
Transport document description :UN 1866, 3, III, (D/E)
CLEARMARINEGEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 7/9
Packing group (ADR) :III
Class (ADR) :3-Flammable liquid
Hazard identification number (Kemler No.):33
Classification code (ADR) :F1
Danger labels (ADR) :3-Flammable liquids
Orange plates :
Tunnel restriction code :D/E
LQ :5L
Exceptedquantities (ADR) :E2
Transport by sea
UN-No. (IMDG) :1866
Proper Shipping Name (IMDG) :RESIN SOLUTION
Class (IMDG) :3-Flammable liquids
Packing group (IMDG) :III-substances presenting low danger
Air transport
UN-No.(IATA) :1866
Proper Shipping Name (IATA) :RESIN SOLUTION
Class (IATA) :3-Flammable Liquids
Packing group (IATA) :III-Minor Danger
SECTION 15:Regulatory information
15.1. US Federal regulations
styrene, inhibited (100-42-5)
RQ (Reportable quantity, section 304 of EPA's
List of Lists) :
1000 lb
SARA Section 311/312 Hazard Classes Immediate (acute) health hazard
Reactive hazard
Fire hazard
Delayed (chronic) health hazard
15.2. International regulations
CANADA
No additional information available
EU-Regulations
No additional information available
Classification according to Regulation (EC) No. 1272/2008 [CLP]
Flam. Liq. 2 H225
Acute Tox. 4 (Inhalation:dust,mist)H332
Skin Irrit. 2 H315
Eye Irrit. 2 H319
Muta. 1B H340
Carc. 1B H350
Full textof H-phrases: see section 16
CLEARMARINEGEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 8/9
Classification according to Directive 67/548/EEC or 1999/45/EC
Carc.Cat.2; R45
Muta.Cat.2; R46
F; R11
Xn; R20
Xi; R36/38
Full text of R-phrases: see section 16
15.2.2.National regulations
styrene, inhibited (100-42-5)
Listed on EPA's Hazardous Air Pollutants (HAPS)
15.3. US State regulations
styrene, inhibited (100-42-5)
U.S.-California-
Proposition 65-
Carcinogens List
U.S.-California-
Proposition 65-
Developmental Toxicity
U.S.-California-
Proposition65-
Reproductive Toxicity-
Female
U.S.-California-
Proposition 65-
Reproductive Toxicity-Male
No significance risk level
(NSRL)
styrene, inhibited (100-42-5)
U.S.-Massachusetts-Right To Know List
U.S.-New Jersey-Right to Know Hazardous Substance List
U.S.-Pennsylvania-RTK (Right to Know)-Environmental Hazard List
SECTION 16:Other information
Data sources :REGULATION (EC) No 1272/2008 OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 16 December 2008 on classification,labeling and packaging of substances and
mixtures, amending and repealing Directives 67/548/EEC and 1999/45/EC, and amending
Regulation (EC) No 1907/2006.
Other information :None.
Full text of H-phrases: see section 16:
------Acute Tox. 4 (Inhalation:vapour) Acute toxicity (inhalation:vapour) Category 4
------Carc. 2 Carcinogenicity Category 2
------Carc. Not classified Carcinogenicity Not classified
------Eye Irrit. 2A Serious eye damage/eye irritation Category 2A
------Flam. Liq. 3 Flammableliquids Category 3
------Skin Irrit. 2 Skin corrosion/irritation Category 2
------H226 Flammable liquid and vapor
------H315 Causes skin irritation
------H319 Causes serious eye irritation
------H332 Harmful if inhaled
------H351 Suspected ofcausing cancer
NFPA health hazard :2-Intense or continued exposure could cause temporary
incapacitation or possible residual injury unless prompt
medical attention is given.
NFPA fire hazard :3-Liquids and solids that can be ignited under almost all
ambient conditions.
NFPA reactivity :2-Normally unstable and readily undergo violent
decomposition but do not detonate. Also: may react
violently with water or may form potentially explosive
mixtures with water.
CLEARMARINEGEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 9/9
HMIS III Rating
Health :2Moderate Hazard-Temporary or minor injury may occur
Flammability :3 Serious Hazard
Physical :1 Slight Hazard
Personal Protection :H
SDS US (GHS HazCom 2012)
To the best of our knowledge this SDS is accurate. The the extent allowed by law, thisstatement is made in lieu of an other warranties, expressed or implied including but not limited to any implied
warranty of merchantability or fitness for a particular purpose and is in lieu of any other obligations or liability on the part of Dura Technoligies, Inc.
by | Sep 27, 2025
INDEX
CR4002T
CR4002TCG
CR4002TCP
CR4002TCQ
CR4002TG
CR4002TP
CR4002TQ
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
Date of issue:10/13/2014 Revision date: Supersedes:
10/13/2014 EN(English US) Page 1
SECTION 1:Identification of the substance/mixture and of the company/undertaking
1.1. Product identifier
Product form :Mixture liquidresin
Trade name :Black Tooling GelCoat
CAS No :Mixture
Product code :CR4002TCP, CR4002TCQ, CR4002TCG
Formula :NA
1.2. Relevant identified uses of the substance or mixture and uses advised against
Use of the substance/mixture :TOOLING GEL COAT
1.3. Details of the supplier of the safety data sheet
Composite Resources is supplied by Revchem Composites. 2720 South Willow Ave., Bloomington, CA 923161-800-281-4975
1.4. Emergency telephone number
Emergency number :800.424.9300
CHEMTREC: 1-800-424-9300
SECTION 2:Hazards identification
2.1. Classification of the substance or mixture
Classification (GHS-US)
Flam. Liq. 3 H226
Skin Irrit. 2 H315
Eye Irrit. 2A H319
Carc. Not classified
2.2. Label elements
GHS-US labeling
Hazard pictograms (GHS-US) :
GHS02 GHS07
Signal word (GHS-US) :Warning
Hazard statements (GHS-US) :H226-Flammable liquid and vapor
H315-Causes skin irritation
H319-Causes serious eye irritation
Precautionary statements (GHS-US) :P210-Keep away from heat, hot surfaces, open flames, sparks.-No smoking
P233-Keep container tightly closed
P240-Ground/bond container and receiving equipment
P241-Useexplosion-proof electrical, lighting, ventilating equipment
P242-Use only non-sparking tools
P243-Take precautionary measures against static discharge
P264-Wash EXPOSED AREA. thoroughly after handling
P280-Wear eye protection, protective clothing,protective gloves
P302+P352-IF ON SKIN: Wash with plenty of soap and water
P303+P361+P353-IF ON SKIN (or hair): Remove/Take off immediately all contaminated
clothing. Rinse skin with water/shower
P305+P351+P338-If in eyes: Rinse cautiously with waterfor several minutes. Remove contact
lenses, if present and easy to do. Continue rinsing
P321-Specific treatment (see SEEK MEDICAL AID. on this label)
P332+P313-If skin irritation occurs: Get medical advice/attention
P337+P313-If eye irritation persists: Get medical advice/attention
P362-Take off contaminated clothing and wash before reuse
P370+P378-In case of fire: Use carbon dioxide (CO2), dry chemical powder, foam to
extinguish
P403+P235-Store in a well-ventilated place. Keep cool
P501-Dispose of contents/container to LOCAL, STATE, AND NATIONAL REGULATIONS.
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 2/9
2.3. Other hazards
No additional information available
2.4. Unknown acute toxicity (GHS-US)
No data available
SECTION 3:Composition/information on ingredients
3.1. Substance
Not applicable
Full text of H-phrases: see section 16
3.2. Mixture
Name Product identifier % Classification (GHS-US)
Unsaturated Polyester Resin (CAS No)TRADE SECRET <= 50 Not classified
styrene, inhibited (CAS No)100-42-5 <= 41 Flam. Liq. 3, H226
Acute Tox. 4 (Inhalation:vapour),
H332
Skin Irrit. 2, H315
Eye Irrit. 2A, H319
Carc. 2, H351
methyl ethyl ketone (CAS No)78-93-3 <= 5 Flam. Liq. 2, H225
cobalt(II) 2-ethylhexanoate (CAS No)136-52-7 <= 0.5 Carc. 2, H351
SECTION 4:First aid measures
4.1. Description of first aid measures
First-aid measures general :Never give anything by mouth to an unconscious person. If you feel unwell, seek medical advice
(show the label where possible).
First-aid measures after inhalation :Assure fresh air breathing. Allow the victim to rest. Remove to fresh air and keep at rest in a
position comfortable for breathing. Call a POISON CENTER/doctor/physician if you feel unwell.
First-aid measures after skin contact :Rinse skin with water/shower. Remove/Take off immediately all contaminated clothing. Wash
with plenty of soap and water. Wash contaminated clothing before reuse. If skin irritation occurs:
wash throughly for five minutes. seek medical attention. Get medical advice/attention. Specific
treatment (see seek medical attention. on this label).
First-aid measures after eye contact :Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to
do. Continue rinsing. If eye irritation persists: SEEK IMMEDIATE MEDICAL ATTENTION. Get
medical advice/attention.
First-aid measures after ingestion :Rinse mouth. Do NOT induce vomiting. Obtain emergency medical attention.
4.2. Most important symptoms and effects, both acute and delayed
Symptoms/injuries :May cause genetic defects (avoid skin contact and inhalation.). May cause cancer (avoid skin
contact and inhalation.).
Symptoms/injuries after inhalation :Danger of serious damage to health by prolonged exposure through inhalation. Harmful if
inhaled.
Symptoms/injuries after skin contact :Causes skin irritation.
Symptoms/injuries after eye contact :Causes serious eye irritation.
4.3. Indication of any immediate medical attention and special treatment needed
No additional information available
SECTION 5:Firefighting measures
5.1. Extinguishing media
suitable extinguishing media :Foam. Dry powder. Carbon dioxide. Water spray. Sand.
Unsuitable extinguishing media :Do not use a heavy water stream.
5.2. Special hazards arising from the substance or mixture
Fire hazard :Highly flammable liquid and vapor.
Explosion hazard :May form flammable/explosive vapor-air mixture.
Reactivity :No reactivity hazard other than the effects described in sub-sections below.
5.3. Advice for firefighters
Firefighting instructions :Use water sprayor fog for cooling exposed containers. Exercise caution when fighting any
chemical fire. Avoid (reject) fire-fighting water to enter environment.
Protection during firefighting :Do not enter fire area without proper protective equipment, including respiratory protection.
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 3/9
SECTION 6:Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
General measures :Remove ignition sources. Use special care to avoid static electric charges. No naked lights. No
smoking.
6.1.1.For non-emergency personnel
Protective equipment :Gloves. Protective goggles. Protective clothing.
Emergency procedures :Evacuate unnecessary personnel.
6.1.2.For emergency responders
Protective equipment :Equip cleanup crew with proper protection.
Emergency procedures :Ventilate area.
6.2. Environmental precautions
Prevent entry to sewers and public waters. Notify authorities if liquid enters sewers or public waters.
6.3. Methods and material for containment and cleaning up
For containment :Dam up the liquid spill. Contain released substance, pump into suitable containers.
Methods for cleaning up :Soak up spills with inert solids, such as clay or diatomaceous earth as soon as possible. Collect
spillage. Store away from other materials.
6.4. Reference to other sections
See Heading 8. Exposure controls and personal protection.
SECTION 7:Handling and storage
7.1. Precautions for safe handling
Additional hazards when processed :Handle empty containers with care because residual vaporsare flammable.
Precautions for safe handling :Wash hands and other exposed areas with mild soap and water before eat, drink or smoke and
when leaving work. Provide good ventilation in process area to prevent formation of vapor. No
naked lights. No smoking. Use only non-sparking tools. Use only outdoors or in a well-ventilated
area. Avoid breathing DUST, FUMES, MIST, OR VAPORS. Obtain special instructions before
use. Do not handle until all safety precautions have been read and understood. Eliminate all
ignition sources if safe to do so.
Hygiene measures :Wash HANDS thoroughly after handling.
7.2. Conditions for safe storage, including any incompatibilities
Technical measures :Proper grounding procedures to avoid static electricity should be followed.Ground/bond
container and receiving equipment. Use explosion-proof electrical, ventilating and lighting
equipment. equipment.
Storage conditions :Keep only in the original container in a cool, well ventilated place away from : HEAT SPARKS
OR OPEN FLAMES. Keep in fireproof place. Keep container tightly closed.
Incompatible products :Strong bases. strong acids.
Incompatible materials :Sources of ignition. Direct sunlight. Heat sources.
7.3. Specific end use(s)
No additional information available
SECTION 8:Exposure controls/personal protection
8.1. Control parameters
styrene, inhibited (100-42-5)
USA ACGIH ACGIH TWA (ppm) 20 ppm
USA ACGIH ACGIH STEL (ppm) 40 ppm
methyl ethyl ketone (78-93-3)
USA ACGIH ACGIH TWA (ppm) 200 ppm
USA ACGIH ACGIHSTEL (ppm) 300 ppm
8.2. Exposure controls
Appropriate engineering controls :Ensure exposure is below occupational exposure limits (where available).
Personal protective equipment :Avoid all unnecessary exposure.
Hand protection :Wear protective gloves.
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 4/9
Eye protection :Chemical goggles or safety glasses.
Skin and body protection :Wear suitable protective clothing.
Respiratory protection :Wear approved mask.
Other information :When using, do not eat, drink or smoke.
SECTION 9:Physical and chemical properties
9.1. Information on basic physical and chemical properties
Physical state :Liquid
Color :Black
Odor :Characteristic
Odor threshold :No data available
pH :No data available
Relative evaporation rate (butyl acetate=1):No data available
Melting point :No data available
Freezing point :No data available
Boiling point : 64 C
Flash point :30-34 C
Auto-ignition temperature :No data available
Decomposition temperature :No data available
Flammability (solid, gas) :No data available
Vapor pressure :No data available
Relative vapor density at 20 C :No data available
Relative density : 1.1
Solubility :No data available
Log Pow :No data available
Log Kow :No data available
Viscosity, kinematic :No data available
Viscosity, dynamic :No data available
Explosive properties :No data available
Oxidizing properties :No data available
Explosive limits :No data available
9.2. Other information
No additionalinformation available
SECTION 10:Stability and reactivity
10.1.Reactivity
No reactivity hazard other than the effects described in sub-sections below.
10.2.Chemical stability
Polymerization can result in formation of solid deposits, even in vapour space. Not established. Highly flammable liquid and vapor. May form
flammable/explosive vapor-air mixture.
10.3.Possibility of hazardous reactions
Not established.
10.4.Conditions to avoid
Direct sunlight. Extremely high or low temperatures. Open flame.
10.5.Incompatible materials
strong acids. Strong bases.
10.6.Hazardous decomposition products
fume. Carbon monoxide. Carbon dioxide. May release flammable gases.
SECTION 11:Toxicological information
11.1.Information on toxicological effects
Acute toxicity :Not classified
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 5/9
BLACK TOOLING GEL COAT (f )mixture
ATE CLP (dust, mist) 1.500 mg/l/4h
styrene, inhibited (100-42-5)
LD50 oral rat 5000 mg/kg (>6000 mg/kg bodyweight; Rat; Rat)
LD50 dermal rat 2820 mg/kg (>2000 mg/kg bodyweight; Rat; Rat;Experimental value)
LD50 dermal rabbit 5010 mg/kg (Rabbit)
LC50 inhalation rat (mg/l) 12 mg/l/4h (Rat)
LC50 inhalation rat (ppm) 2770 ppm/4h (Rat)
ATE CLP (oral) 5000.000 mg/kg
ATE CLP (dermal) 5010.000 mg/kg
methyl ethyl ketone (78-93-3)
LD50 oral rat 2737 mg/kg (2054 mg/kg; 2328 mg/kg; Rat; Rat; Rat)
LD50 dermal rabbit 6480 mg/kg (>10; Rabbit; Rabbit; Experimental value,>10; Rabbit; Rabbit; Experimental value)
LC50 inhalation rat (mg/l) 34 mg/l/4h (Rat)
LC50 inhalation rat (ppm) 11300 ppm/4h(Rat)
ATE CLP (oral) 2737.000 mg/kg
ATE CLP (dermal) 6480.000 mg/kg
Skin corrosion/irritation :Causes skin irritation.
Serious eye damage/irritation :Causes serious eye irritation.
Respiratory or skin sensitization :Not classified
Germ cell mutagenicity :Not classified
Carcinogenicity :Not classified.
styrene, inhibited (100-42-5)
IARC group 2B-Possibly Carcinogenic to Humans
cobalt(II) 2-ethylhexanoate (136-52-7)
IARC group 2B-Possibly Carcinogenic to Humans
Reproductive toxicity :Not classified
Based on available data, the classification criteria are not met
Specific target organ toxicity (single exposure):Not classified
Specific target organ toxicity (repeated
exposure)
:Not classified
Based on available data, the classification criteria are not met
Aspiration hazard :Not classified
Based on available data, the classification criteria are not met
Potential Adverse human health effects and
symptoms
:Harmful if inhaled.
Symptoms/injuries after inhalation :Dangerof serious damage to health by prolonged exposure through inhalation. Harmful if
inhaled.
Symptoms/injuries after skin contact :Causes skin irritation.
Symptoms/injuries after eye contact :Causes serious eye irritation.
SECTION 12:Ecological information
12.1.Toxicity
styrene, inhibited (100-42-5)
LC50 fish 1 25 mg/l (96 h; Lepomis macrochirus)
LC50 other aquatic organisms 1 10-100 mg/l (96 h)
EC50 Daphnia 1 23 mg/l (48 h; Daphnia magna; LOCOMOTOR EFFECT)
LC50 fish 2 32 mg/l (96 h; Pimephales promelas)
EC50 Daphnia 2 27 mg/l (24 h; Daphnia magna)
TLM fish 1 25.1 mg/l (96 h; Lepomis macrochirus; SOFT WATER)
TLM fish 2 46.4 mg/l (96 h; Pimephales promelas; SOFT WATER)
TLM other aquatic organisms 1 10-100,96 h
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 6/9
styrene, inhibited (100-42-5)
Threshold limit other aquatic organisms 1 10-100,96 h; Pseudomonas putida
Threshold limit other aquatic organisms 272 mg/l
Threshold limit algae 1 > 200 mg/l (192 h; Scenedesmus quadricauda; INHIBITORY)
Threshold limit algae 2 67 mg/l (Microcystis aeruginosa; INHIBITORY)
methyl ethyl ketone (78-93-3)
LC50 fish 1 1690 mg/l (96 h; Lepomis macrochirus; LETHAL)
EC50 Daphnia 1 308 mg/l (48 h; Daphnia magna; LOCOMOTOR EFFECT)
LC50 fish 2 2990 mg/l (96 h; Pimephales promelas)
TLM fish 1 5600 mg/l (96 h; Gambusia affinis)
TLM fish 2 1690 mg/l (96 h; Lepomis macrochirus)
TLM other aquatic organisms 1 > 1000 ppm (96 h)
Threshold limit algae 1 110 mg/l (168 h; Microcystis aeruginosa)
Threshold limit algae 2 4300 mg/l (192 h; Scenedesmus quadricauda)
12.2.Persistence and degradability
BLACK TOOLING GEL COAT (mixture)
Persistence and degradability Not established.
styrene, inhibited (100-42-5)
Persistence and degradability Readily biodegradable in water. Not readily biodegradable in water. Forming sediments in
water. Non degradable in the soil. Adsorbs into the soil. Photodegradation in the air. Not
established.
Chemical oxygen demand (COD) 2.80 g O /g substance
ThOD 3.07 g O /g substance
BOD (% of ThOD) 0.42 % ThOD
methyl ethyl ketone (78-93-3)
Persistence and degradability Readily biodegradable in water. Biodegradable in the soil. Biodegradable in the soil under
anaerobic conditions. Not established.
Biochemical oxygen demand (BOD) 1.92 g O /g substance
Chemical oxygen demand (COD) 2.31 g O /g substance
ThOD 2.44g O /g substance
BOD (% of ThOD) 0.79 % ThOD
cobalt(II) 2-ethylhexanoate (136-52-7)
Persistence and degradability Biodegradability in water: no data available.
Unsaturated Polyester Resin (TRADE SECRET)
Persistence and degradability Not established.
12.3.Bioaccumulative potential
BLACK TOOLING GEL COAT (mixture)
Bioaccumulative potential Not established.
styrene, inhibited (100-42-5)
BCF fish 1 12-77 (QSAR)
BCF fish 2 35.5 (Carassius auratus)
Log Pow 2.95-3.16 (Experimental value)
Bioaccumulative potential Low potential for bioaccumulation (BCF < 500). Not established.
methyl ethyl ketone (78-93-3)
Log Pow 0.3 (Experimental value; 40 C,Experimental value; 40 C)
Bioaccumulative potential Low potential for bioaccumulation (Log Kow < 4). Not established.
cobalt(II) 2-ethylhexanoate (136-52-7)
Bioaccumulative potential No bioaccumulation data available.
Unsaturated Polyester Resin (TRADE SECRET)
Bioaccumulative potential Not established.
12.4.Mobility in soil
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 7/9
styrene,inhibited (100-42-5)
Surface tension 0.032 N/m (19 C)
methyl ethyl ketone (78-93-3)
Surface tension 0.024 N/m (20 C)
Ecology-soil Slightly harmful to plants.
12.5.Other adverse effects
Other information :Avoid release to the environment.
SECTION 13:Disposal considerations
13.1.Waste treatment methods
Waste disposal recommendations :Dispose in a safe manner in accordance with local/national regulations. Dispose of
contents/container to approved disposal site.
Additional information :Handle empty containers with care because residual vapors are flammable.
Ecology-waste materials :Avoid release to the environment.
SECTION 14:Transport information
In accordance with DOT
UN-No.(DOT) :UN1866
DOT Proper Shipping Name :RESIN SOLUTION
Department of Transportation (DOT) Hazard
Classes
:3-Class 3-Flammable and combustible liquid 49 CFR 173.120
Hazard labels (DOT) :3-Flammable liquid
Packing group (DOT) :III-Minor Danger
Additional information
Other information :No supplementary information available.
ADR
Transport document description :UN 1866, 3, III, (D/E)
Packing group (ADR) :III
Class (ADR) :3-Flammable liquid
Hazard identification number (Kemler No.):33
Classification code (ADR) :F1
Danger labels(ADR) :3-Flammable liquids
Orange plates :
Tunnel restriction code :D/E
LQ :5L
Excepted quantities (ADR) :E2
Transport by sea
UN-No. (IMDG) :1866
Proper Shipping Name (IMDG) :RESIN SOLUTION
Class (IMDG) :3-Flammable liquids
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 8/9
Packinggroup (IMDG) :III-substances presenting low danger
Air transport
UN-No.(IATA) :1866
Proper Shipping Name (IATA) :RESIN SOLUTION
Class (IATA) :3-Flammable Liquids
Packing group (IATA) :III-Minor Danger
SECTION 15:Regulatory information
15.1. US Federal regulations
styrene, inhibited (100-42-5)
RQ (Reportable quantity, section 304 of EPA's
List of Lists) :
1000 lb
SARA Section 311/312 Hazard Classes Immediate (acute) health hazard
Reactive hazard
Fire hazard
Delayed (chronic) health hazard
methyl ethyl ketone (78-93-3)
RQ (Reportable quantity, section 304 of EPA's
List of Lists) :
5000 lb
15.2. International regulations
CANADA
No additional information available
EU-Regulations
No additional information available
Classification according to Regulation (EC) No. 1272/2008 [CLP]
Flam. Liq. 2 H225
Acute Tox. 4 (Inhalation:dust,mist)H332
Skin Irrit. 2 H315
Eye Irrit. 2 H319
Muta. 1B H340
Carc. 1B H350
Full text of H-phrases: see section 16
Classification according to Directive 67/548/EEC or 1999/45/EC
Carc.Cat.2; R45
Muta.Cat.2; R46
F; R11
Xn; R20
Xi; R36/38
Full text of R-phrases: see section 16
15.2.2.National regulations
styrene, inhibited (100-42-5)
Listed on EPA's Hazardous Air Pollutants (HAPS)
15.3. US State regulations
styrene, inhibited (100-42-5)
U.S.-California-
Proposition 65-
Carcinogens List
U.S.-California-
Proposition 65-
Developmental Toxicity
U.S.-California-
Proposition 65-
Reproductive Toxicity-
U.S.-California-
Proposition 65-
Reproductive Toxicity-Male
No significance risk level
(NSRL)
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 9/9
styrene, inhibited (100-42-5)
Female
styrene, inhibited (100-42-5)
U.S.-Massachusetts-Right To Know List
U.S.-New Jersey-Right to Know Hazardous Substance List
U.S.-Pennsylvania-RTK (Right to Know)-Environmental Hazard List
SECTION 16:Other information
Data sources :REGULATION (EC) No 1272/2008 OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 16 December 2008 on classification, labeling and packaging of substances and
mixtures, amending and repealing Directives 67/548/EEC and 1999/45/EC, and amending
Regulation (EC) No 1907/2006.
Other information :None.
Full text of H-phrases: see section 16:
------Acute Tox. 4 (Inhalation:vapour) Acute toxicity (inhalation:vapour) Category 4
------Carc. 2 Carcinogenicity Category 2
------Carc. Not classified Carcinogenicity Not classified
------Eye Irrit. 2A Serious eye damage/eye irritation Category 2A
------Flam. Liq. 2 Flammable liquids Category 2
------Flam. Liq. 3 Flammable liquids Category 3
------Skin Irrit. 2 Skin corrosion/irritation Category 2
------H225 Highly flammable liquid and vapor
------H226 Flammable liquid and vapor
------H315 Causes skin irritation
------H319 Causes serious eye irritation
------H332 Harmful if inhaled
------H351 Suspected of causing cancer
NFPA health hazard :2-Intense or continued exposure could cause temporary
incapacitation or possible residual injury unless prompt
medical attention is given.
NFPA fire hazard :3-Liquids and solids that can be ignited under almost all
ambient conditions.
NFPA reactivity :2-Normally unstable and readily undergo violent
decomposition but do not detonate. Also: may react
violently with water or may form potentially explosive
mixtures with water.
HMIS III Rating
Health :2 Moderate Hazard-Temporary or minor injury may occur
Flammability :3 Serious Hazard
Physical :1 Slight Hazard
Personal Protection :H
SDS US (GHS HazCom 2012)
To the best of our knowledge this SDS is accurate. The the extent allowed by law, this statement is made in lieu of an other warranties, expressed or implied including but not limited to any implied
warranty of merchantability or fitness for a particular purpose and is in lieu of any otherobligations or liability on the part of Dura Technoligies, Inc.
by | Sep 27, 2025
INDEX
CR4002T
CR4002TCG
CR4002TCP
CR4002TCQ
CR4002TG
CR4002TP
CR4002TQ
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
Date of issue:10/13/2014 Revision date: Supersedes:
10/13/2014 EN(English US) Page 1
SECTION 1:Identification of the substance/mixture and of the company/undertaking
1.1. Product identifier
Product form :Mixture liquidresin
Trade name :Black Tooling GelCoat
CAS No :Mixture
Product code :CR4002TCP, CR4002TCQ, CR4002TCG
Formula :NA
1.2. Relevant identified uses of the substance or mixture and uses advised against
Use of the substance/mixture :TOOLING GEL COAT
1.3. Details of the supplier of the safety data sheet
Composite Resources is supplied by Revchem Composites. 2720 South Willow Ave., Bloomington, CA 923161-800-281-4975
1.4. Emergency telephone number
Emergency number :800.424.9300
CHEMTREC: 1-800-424-9300
SECTION 2:Hazards identification
2.1. Classification of the substance or mixture
Classification (GHS-US)
Flam. Liq. 3 H226
Skin Irrit. 2 H315
Eye Irrit. 2A H319
Carc. Not classified
2.2. Label elements
GHS-US labeling
Hazard pictograms (GHS-US) :
GHS02 GHS07
Signal word (GHS-US) :Warning
Hazard statements (GHS-US) :H226-Flammable liquid and vapor
H315-Causes skin irritation
H319-Causes serious eye irritation
Precautionary statements (GHS-US) :P210-Keep away from heat, hot surfaces, open flames, sparks.-No smoking
P233-Keep container tightly closed
P240-Ground/bond container and receiving equipment
P241-Useexplosion-proof electrical, lighting, ventilating equipment
P242-Use only non-sparking tools
P243-Take precautionary measures against static discharge
P264-Wash EXPOSED AREA. thoroughly after handling
P280-Wear eye protection, protective clothing,protective gloves
P302+P352-IF ON SKIN: Wash with plenty of soap and water
P303+P361+P353-IF ON SKIN (or hair): Remove/Take off immediately all contaminated
clothing. Rinse skin with water/shower
P305+P351+P338-If in eyes: Rinse cautiously with waterfor several minutes. Remove contact
lenses, if present and easy to do. Continue rinsing
P321-Specific treatment (see SEEK MEDICAL AID. on this label)
P332+P313-If skin irritation occurs: Get medical advice/attention
P337+P313-If eye irritation persists: Get medical advice/attention
P362-Take off contaminated clothing and wash before reuse
P370+P378-In case of fire: Use carbon dioxide (CO2), dry chemical powder, foam to
extinguish
P403+P235-Store in a well-ventilated place. Keep cool
P501-Dispose of contents/container to LOCAL, STATE, AND NATIONAL REGULATIONS.
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 2/9
2.3. Other hazards
No additional information available
2.4. Unknown acute toxicity (GHS-US)
No data available
SECTION 3:Composition/information on ingredients
3.1. Substance
Not applicable
Full text of H-phrases: see section 16
3.2. Mixture
Name Product identifier % Classification (GHS-US)
Unsaturated Polyester Resin (CAS No)TRADE SECRET <= 50 Not classified
styrene, inhibited (CAS No)100-42-5 <= 41 Flam. Liq. 3, H226
Acute Tox. 4 (Inhalation:vapour),
H332
Skin Irrit. 2, H315
Eye Irrit. 2A, H319
Carc. 2, H351
methyl ethyl ketone (CAS No)78-93-3 <= 5 Flam. Liq. 2, H225
cobalt(II) 2-ethylhexanoate (CAS No)136-52-7 <= 0.5 Carc. 2, H351
SECTION 4:First aid measures
4.1. Description of first aid measures
First-aid measures general :Never give anything by mouth to an unconscious person. If you feel unwell, seek medical advice
(show the label where possible).
First-aid measures after inhalation :Assure fresh air breathing. Allow the victim to rest. Remove to fresh air and keep at rest in a
position comfortable for breathing. Call a POISON CENTER/doctor/physician if you feel unwell.
First-aid measures after skin contact :Rinse skin with water/shower. Remove/Take off immediately all contaminated clothing. Wash
with plenty of soap and water. Wash contaminated clothing before reuse. If skin irritation occurs:
wash throughly for five minutes. seek medical attention. Get medical advice/attention. Specific
treatment (see seek medical attention. on this label).
First-aid measures after eye contact :Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to
do. Continue rinsing. If eye irritation persists: SEEK IMMEDIATE MEDICAL ATTENTION. Get
medical advice/attention.
First-aid measures after ingestion :Rinse mouth. Do NOT induce vomiting. Obtain emergency medical attention.
4.2. Most important symptoms and effects, both acute and delayed
Symptoms/injuries :May cause genetic defects (avoid skin contact and inhalation.). May cause cancer (avoid skin
contact and inhalation.).
Symptoms/injuries after inhalation :Danger of serious damage to health by prolonged exposure through inhalation. Harmful if
inhaled.
Symptoms/injuries after skin contact :Causes skin irritation.
Symptoms/injuries after eye contact :Causes serious eye irritation.
4.3. Indication of any immediate medical attention and special treatment needed
No additional information available
SECTION 5:Firefighting measures
5.1. Extinguishing media
suitable extinguishing media :Foam. Dry powder. Carbon dioxide. Water spray. Sand.
Unsuitable extinguishing media :Do not use a heavy water stream.
5.2. Special hazards arising from the substance or mixture
Fire hazard :Highly flammable liquid and vapor.
Explosion hazard :May form flammable/explosive vapor-air mixture.
Reactivity :No reactivity hazard other than the effects described in sub-sections below.
5.3. Advice for firefighters
Firefighting instructions :Use water sprayor fog for cooling exposed containers. Exercise caution when fighting any
chemical fire. Avoid (reject) fire-fighting water to enter environment.
Protection during firefighting :Do not enter fire area without proper protective equipment, including respiratory protection.
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 3/9
SECTION 6:Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
General measures :Remove ignition sources. Use special care to avoid static electric charges. No naked lights. No
smoking.
6.1.1.For non-emergency personnel
Protective equipment :Gloves. Protective goggles. Protective clothing.
Emergency procedures :Evacuate unnecessary personnel.
6.1.2.For emergency responders
Protective equipment :Equip cleanup crew with proper protection.
Emergency procedures :Ventilate area.
6.2. Environmental precautions
Prevent entry to sewers and public waters. Notify authorities if liquid enters sewers or public waters.
6.3. Methods and material for containment and cleaning up
For containment :Dam up the liquid spill. Contain released substance, pump into suitable containers.
Methods for cleaning up :Soak up spills with inert solids, such as clay or diatomaceous earth as soon as possible. Collect
spillage. Store away from other materials.
6.4. Reference to other sections
See Heading 8. Exposure controls and personal protection.
SECTION 7:Handling and storage
7.1. Precautions for safe handling
Additional hazards when processed :Handle empty containers with care because residual vaporsare flammable.
Precautions for safe handling :Wash hands and other exposed areas with mild soap and water before eat, drink or smoke and
when leaving work. Provide good ventilation in process area to prevent formation of vapor. No
naked lights. No smoking. Use only non-sparking tools. Use only outdoors or in a well-ventilated
area. Avoid breathing DUST, FUMES, MIST, OR VAPORS. Obtain special instructions before
use. Do not handle until all safety precautions have been read and understood. Eliminate all
ignition sources if safe to do so.
Hygiene measures :Wash HANDS thoroughly after handling.
7.2. Conditions for safe storage, including any incompatibilities
Technical measures :Proper grounding procedures to avoid static electricity should be followed.Ground/bond
container and receiving equipment. Use explosion-proof electrical, ventilating and lighting
equipment. equipment.
Storage conditions :Keep only in the original container in a cool, well ventilated place away from : HEAT SPARKS
OR OPEN FLAMES. Keep in fireproof place. Keep container tightly closed.
Incompatible products :Strong bases. strong acids.
Incompatible materials :Sources of ignition. Direct sunlight. Heat sources.
7.3. Specific end use(s)
No additional information available
SECTION 8:Exposure controls/personal protection
8.1. Control parameters
styrene, inhibited (100-42-5)
USA ACGIH ACGIH TWA (ppm) 20 ppm
USA ACGIH ACGIH STEL (ppm) 40 ppm
methyl ethyl ketone (78-93-3)
USA ACGIH ACGIH TWA (ppm) 200 ppm
USA ACGIH ACGIHSTEL (ppm) 300 ppm
8.2. Exposure controls
Appropriate engineering controls :Ensure exposure is below occupational exposure limits (where available).
Personal protective equipment :Avoid all unnecessary exposure.
Hand protection :Wear protective gloves.
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 4/9
Eye protection :Chemical goggles or safety glasses.
Skin and body protection :Wear suitable protective clothing.
Respiratory protection :Wear approved mask.
Other information :When using, do not eat, drink or smoke.
SECTION 9:Physical and chemical properties
9.1. Information on basic physical and chemical properties
Physical state :Liquid
Color :Black
Odor :Characteristic
Odor threshold :No data available
pH :No data available
Relative evaporation rate (butyl acetate=1):No data available
Melting point :No data available
Freezing point :No data available
Boiling point : 64 C
Flash point :30-34 C
Auto-ignition temperature :No data available
Decomposition temperature :No data available
Flammability (solid, gas) :No data available
Vapor pressure :No data available
Relative vapor density at 20 C :No data available
Relative density : 1.1
Solubility :No data available
Log Pow :No data available
Log Kow :No data available
Viscosity, kinematic :No data available
Viscosity, dynamic :No data available
Explosive properties :No data available
Oxidizing properties :No data available
Explosive limits :No data available
9.2. Other information
No additionalinformation available
SECTION 10:Stability and reactivity
10.1.Reactivity
No reactivity hazard other than the effects described in sub-sections below.
10.2.Chemical stability
Polymerization can result in formation of solid deposits, even in vapour space. Not established. Highly flammable liquid and vapor. May form
flammable/explosive vapor-air mixture.
10.3.Possibility of hazardous reactions
Not established.
10.4.Conditions to avoid
Direct sunlight. Extremely high or low temperatures. Open flame.
10.5.Incompatible materials
strong acids. Strong bases.
10.6.Hazardous decomposition products
fume. Carbon monoxide. Carbon dioxide. May release flammable gases.
SECTION 11:Toxicological information
11.1.Information on toxicological effects
Acute toxicity :Not classified
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 5/9
BLACK TOOLING GEL COAT (f )mixture
ATE CLP (dust, mist) 1.500 mg/l/4h
styrene, inhibited (100-42-5)
LD50 oral rat 5000 mg/kg (>6000 mg/kg bodyweight; Rat; Rat)
LD50 dermal rat 2820 mg/kg (>2000 mg/kg bodyweight; Rat; Rat;Experimental value)
LD50 dermal rabbit 5010 mg/kg (Rabbit)
LC50 inhalation rat (mg/l) 12 mg/l/4h (Rat)
LC50 inhalation rat (ppm) 2770 ppm/4h (Rat)
ATE CLP (oral) 5000.000 mg/kg
ATE CLP (dermal) 5010.000 mg/kg
methyl ethyl ketone (78-93-3)
LD50 oral rat 2737 mg/kg (2054 mg/kg; 2328 mg/kg; Rat; Rat; Rat)
LD50 dermal rabbit 6480 mg/kg (>10; Rabbit; Rabbit; Experimental value,>10; Rabbit; Rabbit; Experimental value)
LC50 inhalation rat (mg/l) 34 mg/l/4h (Rat)
LC50 inhalation rat (ppm) 11300 ppm/4h(Rat)
ATE CLP (oral) 2737.000 mg/kg
ATE CLP (dermal) 6480.000 mg/kg
Skin corrosion/irritation :Causes skin irritation.
Serious eye damage/irritation :Causes serious eye irritation.
Respiratory or skin sensitization :Not classified
Germ cell mutagenicity :Not classified
Carcinogenicity :Not classified.
styrene, inhibited (100-42-5)
IARC group 2B-Possibly Carcinogenic to Humans
cobalt(II) 2-ethylhexanoate (136-52-7)
IARC group 2B-Possibly Carcinogenic to Humans
Reproductive toxicity :Not classified
Based on available data, the classification criteria are not met
Specific target organ toxicity (single exposure):Not classified
Specific target organ toxicity (repeated
exposure)
:Not classified
Based on available data, the classification criteria are not met
Aspiration hazard :Not classified
Based on available data, the classification criteria are not met
Potential Adverse human health effects and
symptoms
:Harmful if inhaled.
Symptoms/injuries after inhalation :Dangerof serious damage to health by prolonged exposure through inhalation. Harmful if
inhaled.
Symptoms/injuries after skin contact :Causes skin irritation.
Symptoms/injuries after eye contact :Causes serious eye irritation.
SECTION 12:Ecological information
12.1.Toxicity
styrene, inhibited (100-42-5)
LC50 fish 1 25 mg/l (96 h; Lepomis macrochirus)
LC50 other aquatic organisms 1 10-100 mg/l (96 h)
EC50 Daphnia 1 23 mg/l (48 h; Daphnia magna; LOCOMOTOR EFFECT)
LC50 fish 2 32 mg/l (96 h; Pimephales promelas)
EC50 Daphnia 2 27 mg/l (24 h; Daphnia magna)
TLM fish 1 25.1 mg/l (96 h; Lepomis macrochirus; SOFT WATER)
TLM fish 2 46.4 mg/l (96 h; Pimephales promelas; SOFT WATER)
TLM other aquatic organisms 1 10-100,96 h
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 6/9
styrene, inhibited (100-42-5)
Threshold limit other aquatic organisms 1 10-100,96 h; Pseudomonas putida
Threshold limit other aquatic organisms 272 mg/l
Threshold limit algae 1 > 200 mg/l (192 h; Scenedesmus quadricauda; INHIBITORY)
Threshold limit algae 2 67 mg/l (Microcystis aeruginosa; INHIBITORY)
methyl ethyl ketone (78-93-3)
LC50 fish 1 1690 mg/l (96 h; Lepomis macrochirus; LETHAL)
EC50 Daphnia 1 308 mg/l (48 h; Daphnia magna; LOCOMOTOR EFFECT)
LC50 fish 2 2990 mg/l (96 h; Pimephales promelas)
TLM fish 1 5600 mg/l (96 h; Gambusia affinis)
TLM fish 2 1690 mg/l (96 h; Lepomis macrochirus)
TLM other aquatic organisms 1 > 1000 ppm (96 h)
Threshold limit algae 1 110 mg/l (168 h; Microcystis aeruginosa)
Threshold limit algae 2 4300 mg/l (192 h; Scenedesmus quadricauda)
12.2.Persistence and degradability
BLACK TOOLING GEL COAT (mixture)
Persistence and degradability Not established.
styrene, inhibited (100-42-5)
Persistence and degradability Readily biodegradable in water. Not readily biodegradable in water. Forming sediments in
water. Non degradable in the soil. Adsorbs into the soil. Photodegradation in the air. Not
established.
Chemical oxygen demand (COD) 2.80 g O /g substance
ThOD 3.07 g O /g substance
BOD (% of ThOD) 0.42 % ThOD
methyl ethyl ketone (78-93-3)
Persistence and degradability Readily biodegradable in water. Biodegradable in the soil. Biodegradable in the soil under
anaerobic conditions. Not established.
Biochemical oxygen demand (BOD) 1.92 g O /g substance
Chemical oxygen demand (COD) 2.31 g O /g substance
ThOD 2.44g O /g substance
BOD (% of ThOD) 0.79 % ThOD
cobalt(II) 2-ethylhexanoate (136-52-7)
Persistence and degradability Biodegradability in water: no data available.
Unsaturated Polyester Resin (TRADE SECRET)
Persistence and degradability Not established.
12.3.Bioaccumulative potential
BLACK TOOLING GEL COAT (mixture)
Bioaccumulative potential Not established.
styrene, inhibited (100-42-5)
BCF fish 1 12-77 (QSAR)
BCF fish 2 35.5 (Carassius auratus)
Log Pow 2.95-3.16 (Experimental value)
Bioaccumulative potential Low potential for bioaccumulation (BCF < 500). Not established.
methyl ethyl ketone (78-93-3)
Log Pow 0.3 (Experimental value; 40 C,Experimental value; 40 C)
Bioaccumulative potential Low potential for bioaccumulation (Log Kow < 4). Not established.
cobalt(II) 2-ethylhexanoate (136-52-7)
Bioaccumulative potential No bioaccumulation data available.
Unsaturated Polyester Resin (TRADE SECRET)
Bioaccumulative potential Not established.
12.4.Mobility in soil
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 7/9
styrene,inhibited (100-42-5)
Surface tension 0.032 N/m (19 C)
methyl ethyl ketone (78-93-3)
Surface tension 0.024 N/m (20 C)
Ecology-soil Slightly harmful to plants.
12.5.Other adverse effects
Other information :Avoid release to the environment.
SECTION 13:Disposal considerations
13.1.Waste treatment methods
Waste disposal recommendations :Dispose in a safe manner in accordance with local/national regulations. Dispose of
contents/container to approved disposal site.
Additional information :Handle empty containers with care because residual vapors are flammable.
Ecology-waste materials :Avoid release to the environment.
SECTION 14:Transport information
In accordance with DOT
UN-No.(DOT) :UN1866
DOT Proper Shipping Name :RESIN SOLUTION
Department of Transportation (DOT) Hazard
Classes
:3-Class 3-Flammable and combustible liquid 49 CFR 173.120
Hazard labels (DOT) :3-Flammable liquid
Packing group (DOT) :III-Minor Danger
Additional information
Other information :No supplementary information available.
ADR
Transport document description :UN 1866, 3, III, (D/E)
Packing group (ADR) :III
Class (ADR) :3-Flammable liquid
Hazard identification number (Kemler No.):33
Classification code (ADR) :F1
Danger labels(ADR) :3-Flammable liquids
Orange plates :
Tunnel restriction code :D/E
LQ :5L
Excepted quantities (ADR) :E2
Transport by sea
UN-No. (IMDG) :1866
Proper Shipping Name (IMDG) :RESIN SOLUTION
Class (IMDG) :3-Flammable liquids
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 8/9
Packinggroup (IMDG) :III-substances presenting low danger
Air transport
UN-No.(IATA) :1866
Proper Shipping Name (IATA) :RESIN SOLUTION
Class (IATA) :3-Flammable Liquids
Packing group (IATA) :III-Minor Danger
SECTION 15:Regulatory information
15.1. US Federal regulations
styrene, inhibited (100-42-5)
RQ (Reportable quantity, section 304 of EPA's
List of Lists) :
1000 lb
SARA Section 311/312 Hazard Classes Immediate (acute) health hazard
Reactive hazard
Fire hazard
Delayed (chronic) health hazard
methyl ethyl ketone (78-93-3)
RQ (Reportable quantity, section 304 of EPA's
List of Lists) :
5000 lb
15.2. International regulations
CANADA
No additional information available
EU-Regulations
No additional information available
Classification according to Regulation (EC) No. 1272/2008 [CLP]
Flam. Liq. 2 H225
Acute Tox. 4 (Inhalation:dust,mist)H332
Skin Irrit. 2 H315
Eye Irrit. 2 H319
Muta. 1B H340
Carc. 1B H350
Full text of H-phrases: see section 16
Classification according to Directive 67/548/EEC or 1999/45/EC
Carc.Cat.2; R45
Muta.Cat.2; R46
F; R11
Xn; R20
Xi; R36/38
Full text of R-phrases: see section 16
15.2.2.National regulations
styrene, inhibited (100-42-5)
Listed on EPA's Hazardous Air Pollutants (HAPS)
15.3. US State regulations
styrene, inhibited (100-42-5)
U.S.-California-
Proposition 65-
Carcinogens List
U.S.-California-
Proposition 65-
Developmental Toxicity
U.S.-California-
Proposition 65-
Reproductive Toxicity-
U.S.-California-
Proposition 65-
Reproductive Toxicity-Male
No significance risk level
(NSRL)
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 9/9
styrene, inhibited (100-42-5)
Female
styrene, inhibited (100-42-5)
U.S.-Massachusetts-Right To Know List
U.S.-New Jersey-Right to Know Hazardous Substance List
U.S.-Pennsylvania-RTK (Right to Know)-Environmental Hazard List
SECTION 16:Other information
Data sources :REGULATION (EC) No 1272/2008 OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 16 December 2008 on classification, labeling and packaging of substances and
mixtures, amending and repealing Directives 67/548/EEC and 1999/45/EC, and amending
Regulation (EC) No 1907/2006.
Other information :None.
Full text of H-phrases: see section 16:
------Acute Tox. 4 (Inhalation:vapour) Acute toxicity (inhalation:vapour) Category 4
------Carc. 2 Carcinogenicity Category 2
------Carc. Not classified Carcinogenicity Not classified
------Eye Irrit. 2A Serious eye damage/eye irritation Category 2A
------Flam. Liq. 2 Flammable liquids Category 2
------Flam. Liq. 3 Flammable liquids Category 3
------Skin Irrit. 2 Skin corrosion/irritation Category 2
------H225 Highly flammable liquid and vapor
------H226 Flammable liquid and vapor
------H315 Causes skin irritation
------H319 Causes serious eye irritation
------H332 Harmful if inhaled
------H351 Suspected of causing cancer
NFPA health hazard :2-Intense or continued exposure could cause temporary
incapacitation or possible residual injury unless prompt
medical attention is given.
NFPA fire hazard :3-Liquids and solids that can be ignited under almost all
ambient conditions.
NFPA reactivity :2-Normally unstable and readily undergo violent
decomposition but do not detonate. Also: may react
violently with water or may form potentially explosive
mixtures with water.
HMIS III Rating
Health :2 Moderate Hazard-Temporary or minor injury may occur
Flammability :3 Serious Hazard
Physical :1 Slight Hazard
Personal Protection :H
SDS US (GHS HazCom 2012)
To the best of our knowledge this SDS is accurate. The the extent allowed by law, this statement is made in lieu of an other warranties, expressed or implied including but not limited to any implied
warranty of merchantability or fitness for a particular purpose and is in lieu of any otherobligations or liability on the part of Dura Technoligies, Inc.
by | Sep 27, 2025
INDEX
CR4002T
CR4002TCG
CR4002TCP
CR4002TCQ
CR4002TG
CR4002TP
CR4002TQ
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
Date of issue:10/13/2014 Revision date: Supersedes:
10/13/2014 EN(English US) Page 1
SECTION 1:Identification of the substance/mixture and of the company/undertaking
1.1. Product identifier
Product form :Mixture liquidresin
Trade name :Black Tooling GelCoat
CAS No :Mixture
Product code :CR4002TCP, CR4002TCQ, CR4002TCG
Formula :NA
1.2. Relevant identified uses of the substance or mixture and uses advised against
Use of the substance/mixture :TOOLING GEL COAT
1.3. Details of the supplier of the safety data sheet
Composite Resources is supplied by Revchem Composites. 2720 South Willow Ave., Bloomington, CA 923161-800-281-4975
1.4. Emergency telephone number
Emergency number :800.424.9300
CHEMTREC: 1-800-424-9300
SECTION 2:Hazards identification
2.1. Classification of the substance or mixture
Classification (GHS-US)
Flam. Liq. 3 H226
Skin Irrit. 2 H315
Eye Irrit. 2A H319
Carc. Not classified
2.2. Label elements
GHS-US labeling
Hazard pictograms (GHS-US) :
GHS02 GHS07
Signal word (GHS-US) :Warning
Hazard statements (GHS-US) :H226-Flammable liquid and vapor
H315-Causes skin irritation
H319-Causes serious eye irritation
Precautionary statements (GHS-US) :P210-Keep away from heat, hot surfaces, open flames, sparks.-No smoking
P233-Keep container tightly closed
P240-Ground/bond container and receiving equipment
P241-Useexplosion-proof electrical, lighting, ventilating equipment
P242-Use only non-sparking tools
P243-Take precautionary measures against static discharge
P264-Wash EXPOSED AREA. thoroughly after handling
P280-Wear eye protection, protective clothing,protective gloves
P302+P352-IF ON SKIN: Wash with plenty of soap and water
P303+P361+P353-IF ON SKIN (or hair): Remove/Take off immediately all contaminated
clothing. Rinse skin with water/shower
P305+P351+P338-If in eyes: Rinse cautiously with waterfor several minutes. Remove contact
lenses, if present and easy to do. Continue rinsing
P321-Specific treatment (see SEEK MEDICAL AID. on this label)
P332+P313-If skin irritation occurs: Get medical advice/attention
P337+P313-If eye irritation persists: Get medical advice/attention
P362-Take off contaminated clothing and wash before reuse
P370+P378-In case of fire: Use carbon dioxide (CO2), dry chemical powder, foam to
extinguish
P403+P235-Store in a well-ventilated place. Keep cool
P501-Dispose of contents/container to LOCAL, STATE, AND NATIONAL REGULATIONS.
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 2/9
2.3. Other hazards
No additional information available
2.4. Unknown acute toxicity (GHS-US)
No data available
SECTION 3:Composition/information on ingredients
3.1. Substance
Not applicable
Full text of H-phrases: see section 16
3.2. Mixture
Name Product identifier % Classification (GHS-US)
Unsaturated Polyester Resin (CAS No)TRADE SECRET <= 50 Not classified
styrene, inhibited (CAS No)100-42-5 <= 41 Flam. Liq. 3, H226
Acute Tox. 4 (Inhalation:vapour),
H332
Skin Irrit. 2, H315
Eye Irrit. 2A, H319
Carc. 2, H351
methyl ethyl ketone (CAS No)78-93-3 <= 5 Flam. Liq. 2, H225
cobalt(II) 2-ethylhexanoate (CAS No)136-52-7 <= 0.5 Carc. 2, H351
SECTION 4:First aid measures
4.1. Description of first aid measures
First-aid measures general :Never give anything by mouth to an unconscious person. If you feel unwell, seek medical advice
(show the label where possible).
First-aid measures after inhalation :Assure fresh air breathing. Allow the victim to rest. Remove to fresh air and keep at rest in a
position comfortable for breathing. Call a POISON CENTER/doctor/physician if you feel unwell.
First-aid measures after skin contact :Rinse skin with water/shower. Remove/Take off immediately all contaminated clothing. Wash
with plenty of soap and water. Wash contaminated clothing before reuse. If skin irritation occurs:
wash throughly for five minutes. seek medical attention. Get medical advice/attention. Specific
treatment (see seek medical attention. on this label).
First-aid measures after eye contact :Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to
do. Continue rinsing. If eye irritation persists: SEEK IMMEDIATE MEDICAL ATTENTION. Get
medical advice/attention.
First-aid measures after ingestion :Rinse mouth. Do NOT induce vomiting. Obtain emergency medical attention.
4.2. Most important symptoms and effects, both acute and delayed
Symptoms/injuries :May cause genetic defects (avoid skin contact and inhalation.). May cause cancer (avoid skin
contact and inhalation.).
Symptoms/injuries after inhalation :Danger of serious damage to health by prolonged exposure through inhalation. Harmful if
inhaled.
Symptoms/injuries after skin contact :Causes skin irritation.
Symptoms/injuries after eye contact :Causes serious eye irritation.
4.3. Indication of any immediate medical attention and special treatment needed
No additional information available
SECTION 5:Firefighting measures
5.1. Extinguishing media
suitable extinguishing media :Foam. Dry powder. Carbon dioxide. Water spray. Sand.
Unsuitable extinguishing media :Do not use a heavy water stream.
5.2. Special hazards arising from the substance or mixture
Fire hazard :Highly flammable liquid and vapor.
Explosion hazard :May form flammable/explosive vapor-air mixture.
Reactivity :No reactivity hazard other than the effects described in sub-sections below.
5.3. Advice for firefighters
Firefighting instructions :Use water sprayor fog for cooling exposed containers. Exercise caution when fighting any
chemical fire. Avoid (reject) fire-fighting water to enter environment.
Protection during firefighting :Do not enter fire area without proper protective equipment, including respiratory protection.
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 3/9
SECTION 6:Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
General measures :Remove ignition sources. Use special care to avoid static electric charges. No naked lights. No
smoking.
6.1.1.For non-emergency personnel
Protective equipment :Gloves. Protective goggles. Protective clothing.
Emergency procedures :Evacuate unnecessary personnel.
6.1.2.For emergency responders
Protective equipment :Equip cleanup crew with proper protection.
Emergency procedures :Ventilate area.
6.2. Environmental precautions
Prevent entry to sewers and public waters. Notify authorities if liquid enters sewers or public waters.
6.3. Methods and material for containment and cleaning up
For containment :Dam up the liquid spill. Contain released substance, pump into suitable containers.
Methods for cleaning up :Soak up spills with inert solids, such as clay or diatomaceous earth as soon as possible. Collect
spillage. Store away from other materials.
6.4. Reference to other sections
See Heading 8. Exposure controls and personal protection.
SECTION 7:Handling and storage
7.1. Precautions for safe handling
Additional hazards when processed :Handle empty containers with care because residual vaporsare flammable.
Precautions for safe handling :Wash hands and other exposed areas with mild soap and water before eat, drink or smoke and
when leaving work. Provide good ventilation in process area to prevent formation of vapor. No
naked lights. No smoking. Use only non-sparking tools. Use only outdoors or in a well-ventilated
area. Avoid breathing DUST, FUMES, MIST, OR VAPORS. Obtain special instructions before
use. Do not handle until all safety precautions have been read and understood. Eliminate all
ignition sources if safe to do so.
Hygiene measures :Wash HANDS thoroughly after handling.
7.2. Conditions for safe storage, including any incompatibilities
Technical measures :Proper grounding procedures to avoid static electricity should be followed.Ground/bond
container and receiving equipment. Use explosion-proof electrical, ventilating and lighting
equipment. equipment.
Storage conditions :Keep only in the original container in a cool, well ventilated place away from : HEAT SPARKS
OR OPEN FLAMES. Keep in fireproof place. Keep container tightly closed.
Incompatible products :Strong bases. strong acids.
Incompatible materials :Sources of ignition. Direct sunlight. Heat sources.
7.3. Specific end use(s)
No additional information available
SECTION 8:Exposure controls/personal protection
8.1. Control parameters
styrene, inhibited (100-42-5)
USA ACGIH ACGIH TWA (ppm) 20 ppm
USA ACGIH ACGIH STEL (ppm) 40 ppm
methyl ethyl ketone (78-93-3)
USA ACGIH ACGIH TWA (ppm) 200 ppm
USA ACGIH ACGIHSTEL (ppm) 300 ppm
8.2. Exposure controls
Appropriate engineering controls :Ensure exposure is below occupational exposure limits (where available).
Personal protective equipment :Avoid all unnecessary exposure.
Hand protection :Wear protective gloves.
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 4/9
Eye protection :Chemical goggles or safety glasses.
Skin and body protection :Wear suitable protective clothing.
Respiratory protection :Wear approved mask.
Other information :When using, do not eat, drink or smoke.
SECTION 9:Physical and chemical properties
9.1. Information on basic physical and chemical properties
Physical state :Liquid
Color :Black
Odor :Characteristic
Odor threshold :No data available
pH :No data available
Relative evaporation rate (butyl acetate=1):No data available
Melting point :No data available
Freezing point :No data available
Boiling point : 64 C
Flash point :30-34 C
Auto-ignition temperature :No data available
Decomposition temperature :No data available
Flammability (solid, gas) :No data available
Vapor pressure :No data available
Relative vapor density at 20 C :No data available
Relative density : 1.1
Solubility :No data available
Log Pow :No data available
Log Kow :No data available
Viscosity, kinematic :No data available
Viscosity, dynamic :No data available
Explosive properties :No data available
Oxidizing properties :No data available
Explosive limits :No data available
9.2. Other information
No additionalinformation available
SECTION 10:Stability and reactivity
10.1.Reactivity
No reactivity hazard other than the effects described in sub-sections below.
10.2.Chemical stability
Polymerization can result in formation of solid deposits, even in vapour space. Not established. Highly flammable liquid and vapor. May form
flammable/explosive vapor-air mixture.
10.3.Possibility of hazardous reactions
Not established.
10.4.Conditions to avoid
Direct sunlight. Extremely high or low temperatures. Open flame.
10.5.Incompatible materials
strong acids. Strong bases.
10.6.Hazardous decomposition products
fume. Carbon monoxide. Carbon dioxide. May release flammable gases.
SECTION 11:Toxicological information
11.1.Information on toxicological effects
Acute toxicity :Not classified
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 5/9
BLACK TOOLING GEL COAT (f )mixture
ATE CLP (dust, mist) 1.500 mg/l/4h
styrene, inhibited (100-42-5)
LD50 oral rat 5000 mg/kg (>6000 mg/kg bodyweight; Rat; Rat)
LD50 dermal rat 2820 mg/kg (>2000 mg/kg bodyweight; Rat; Rat;Experimental value)
LD50 dermal rabbit 5010 mg/kg (Rabbit)
LC50 inhalation rat (mg/l) 12 mg/l/4h (Rat)
LC50 inhalation rat (ppm) 2770 ppm/4h (Rat)
ATE CLP (oral) 5000.000 mg/kg
ATE CLP (dermal) 5010.000 mg/kg
methyl ethyl ketone (78-93-3)
LD50 oral rat 2737 mg/kg (2054 mg/kg; 2328 mg/kg; Rat; Rat; Rat)
LD50 dermal rabbit 6480 mg/kg (>10; Rabbit; Rabbit; Experimental value,>10; Rabbit; Rabbit; Experimental value)
LC50 inhalation rat (mg/l) 34 mg/l/4h (Rat)
LC50 inhalation rat (ppm) 11300 ppm/4h(Rat)
ATE CLP (oral) 2737.000 mg/kg
ATE CLP (dermal) 6480.000 mg/kg
Skin corrosion/irritation :Causes skin irritation.
Serious eye damage/irritation :Causes serious eye irritation.
Respiratory or skin sensitization :Not classified
Germ cell mutagenicity :Not classified
Carcinogenicity :Not classified.
styrene, inhibited (100-42-5)
IARC group 2B-Possibly Carcinogenic to Humans
cobalt(II) 2-ethylhexanoate (136-52-7)
IARC group 2B-Possibly Carcinogenic to Humans
Reproductive toxicity :Not classified
Based on available data, the classification criteria are not met
Specific target organ toxicity (single exposure):Not classified
Specific target organ toxicity (repeated
exposure)
:Not classified
Based on available data, the classification criteria are not met
Aspiration hazard :Not classified
Based on available data, the classification criteria are not met
Potential Adverse human health effects and
symptoms
:Harmful if inhaled.
Symptoms/injuries after inhalation :Dangerof serious damage to health by prolonged exposure through inhalation. Harmful if
inhaled.
Symptoms/injuries after skin contact :Causes skin irritation.
Symptoms/injuries after eye contact :Causes serious eye irritation.
SECTION 12:Ecological information
12.1.Toxicity
styrene, inhibited (100-42-5)
LC50 fish 1 25 mg/l (96 h; Lepomis macrochirus)
LC50 other aquatic organisms 1 10-100 mg/l (96 h)
EC50 Daphnia 1 23 mg/l (48 h; Daphnia magna; LOCOMOTOR EFFECT)
LC50 fish 2 32 mg/l (96 h; Pimephales promelas)
EC50 Daphnia 2 27 mg/l (24 h; Daphnia magna)
TLM fish 1 25.1 mg/l (96 h; Lepomis macrochirus; SOFT WATER)
TLM fish 2 46.4 mg/l (96 h; Pimephales promelas; SOFT WATER)
TLM other aquatic organisms 1 10-100,96 h
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 6/9
styrene, inhibited (100-42-5)
Threshold limit other aquatic organisms 1 10-100,96 h; Pseudomonas putida
Threshold limit other aquatic organisms 272 mg/l
Threshold limit algae 1 > 200 mg/l (192 h; Scenedesmus quadricauda; INHIBITORY)
Threshold limit algae 2 67 mg/l (Microcystis aeruginosa; INHIBITORY)
methyl ethyl ketone (78-93-3)
LC50 fish 1 1690 mg/l (96 h; Lepomis macrochirus; LETHAL)
EC50 Daphnia 1 308 mg/l (48 h; Daphnia magna; LOCOMOTOR EFFECT)
LC50 fish 2 2990 mg/l (96 h; Pimephales promelas)
TLM fish 1 5600 mg/l (96 h; Gambusia affinis)
TLM fish 2 1690 mg/l (96 h; Lepomis macrochirus)
TLM other aquatic organisms 1 > 1000 ppm (96 h)
Threshold limit algae 1 110 mg/l (168 h; Microcystis aeruginosa)
Threshold limit algae 2 4300 mg/l (192 h; Scenedesmus quadricauda)
12.2.Persistence and degradability
BLACK TOOLING GEL COAT (mixture)
Persistence and degradability Not established.
styrene, inhibited (100-42-5)
Persistence and degradability Readily biodegradable in water. Not readily biodegradable in water. Forming sediments in
water. Non degradable in the soil. Adsorbs into the soil. Photodegradation in the air. Not
established.
Chemical oxygen demand (COD) 2.80 g O /g substance
ThOD 3.07 g O /g substance
BOD (% of ThOD) 0.42 % ThOD
methyl ethyl ketone (78-93-3)
Persistence and degradability Readily biodegradable in water. Biodegradable in the soil. Biodegradable in the soil under
anaerobic conditions. Not established.
Biochemical oxygen demand (BOD) 1.92 g O /g substance
Chemical oxygen demand (COD) 2.31 g O /g substance
ThOD 2.44g O /g substance
BOD (% of ThOD) 0.79 % ThOD
cobalt(II) 2-ethylhexanoate (136-52-7)
Persistence and degradability Biodegradability in water: no data available.
Unsaturated Polyester Resin (TRADE SECRET)
Persistence and degradability Not established.
12.3.Bioaccumulative potential
BLACK TOOLING GEL COAT (mixture)
Bioaccumulative potential Not established.
styrene, inhibited (100-42-5)
BCF fish 1 12-77 (QSAR)
BCF fish 2 35.5 (Carassius auratus)
Log Pow 2.95-3.16 (Experimental value)
Bioaccumulative potential Low potential for bioaccumulation (BCF < 500). Not established.
methyl ethyl ketone (78-93-3)
Log Pow 0.3 (Experimental value; 40 C,Experimental value; 40 C)
Bioaccumulative potential Low potential for bioaccumulation (Log Kow < 4). Not established.
cobalt(II) 2-ethylhexanoate (136-52-7)
Bioaccumulative potential No bioaccumulation data available.
Unsaturated Polyester Resin (TRADE SECRET)
Bioaccumulative potential Not established.
12.4.Mobility in soil
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 7/9
styrene,inhibited (100-42-5)
Surface tension 0.032 N/m (19 C)
methyl ethyl ketone (78-93-3)
Surface tension 0.024 N/m (20 C)
Ecology-soil Slightly harmful to plants.
12.5.Other adverse effects
Other information :Avoid release to the environment.
SECTION 13:Disposal considerations
13.1.Waste treatment methods
Waste disposal recommendations :Dispose in a safe manner in accordance with local/national regulations. Dispose of
contents/container to approved disposal site.
Additional information :Handle empty containers with care because residual vapors are flammable.
Ecology-waste materials :Avoid release to the environment.
SECTION 14:Transport information
In accordance with DOT
UN-No.(DOT) :UN1866
DOT Proper Shipping Name :RESIN SOLUTION
Department of Transportation (DOT) Hazard
Classes
:3-Class 3-Flammable and combustible liquid 49 CFR 173.120
Hazard labels (DOT) :3-Flammable liquid
Packing group (DOT) :III-Minor Danger
Additional information
Other information :No supplementary information available.
ADR
Transport document description :UN 1866, 3, III, (D/E)
Packing group (ADR) :III
Class (ADR) :3-Flammable liquid
Hazard identification number (Kemler No.):33
Classification code (ADR) :F1
Danger labels(ADR) :3-Flammable liquids
Orange plates :
Tunnel restriction code :D/E
LQ :5L
Excepted quantities (ADR) :E2
Transport by sea
UN-No. (IMDG) :1866
Proper Shipping Name (IMDG) :RESIN SOLUTION
Class (IMDG) :3-Flammable liquids
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 8/9
Packinggroup (IMDG) :III-substances presenting low danger
Air transport
UN-No.(IATA) :1866
Proper Shipping Name (IATA) :RESIN SOLUTION
Class (IATA) :3-Flammable Liquids
Packing group (IATA) :III-Minor Danger
SECTION 15:Regulatory information
15.1. US Federal regulations
styrene, inhibited (100-42-5)
RQ (Reportable quantity, section 304 of EPA's
List of Lists) :
1000 lb
SARA Section 311/312 Hazard Classes Immediate (acute) health hazard
Reactive hazard
Fire hazard
Delayed (chronic) health hazard
methyl ethyl ketone (78-93-3)
RQ (Reportable quantity, section 304 of EPA's
List of Lists) :
5000 lb
15.2. International regulations
CANADA
No additional information available
EU-Regulations
No additional information available
Classification according to Regulation (EC) No. 1272/2008 [CLP]
Flam. Liq. 2 H225
Acute Tox. 4 (Inhalation:dust,mist)H332
Skin Irrit. 2 H315
Eye Irrit. 2 H319
Muta. 1B H340
Carc. 1B H350
Full text of H-phrases: see section 16
Classification according to Directive 67/548/EEC or 1999/45/EC
Carc.Cat.2; R45
Muta.Cat.2; R46
F; R11
Xn; R20
Xi; R36/38
Full text of R-phrases: see section 16
15.2.2.National regulations
styrene, inhibited (100-42-5)
Listed on EPA's Hazardous Air Pollutants (HAPS)
15.3. US State regulations
styrene, inhibited (100-42-5)
U.S.-California-
Proposition 65-
Carcinogens List
U.S.-California-
Proposition 65-
Developmental Toxicity
U.S.-California-
Proposition 65-
Reproductive Toxicity-
U.S.-California-
Proposition 65-
Reproductive Toxicity-Male
No significance risk level
(NSRL)
BLACK TOOLING GEL COAT
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
10/13/2014 EN(English US) 9/9
styrene, inhibited (100-42-5)
Female
styrene, inhibited (100-42-5)
U.S.-Massachusetts-Right To Know List
U.S.-New Jersey-Right to Know Hazardous Substance List
U.S.-Pennsylvania-RTK (Right to Know)-Environmental Hazard List
SECTION 16:Other information
Data sources :REGULATION (EC) No 1272/2008 OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 16 December 2008 on classification, labeling and packaging of substances and
mixtures, amending and repealing Directives 67/548/EEC and 1999/45/EC, and amending
Regulation (EC) No 1907/2006.
Other information :None.
Full text of H-phrases: see section 16:
------Acute Tox. 4 (Inhalation:vapour) Acute toxicity (inhalation:vapour) Category 4
------Carc. 2 Carcinogenicity Category 2
------Carc. Not classified Carcinogenicity Not classified
------Eye Irrit. 2A Serious eye damage/eye irritation Category 2A
------Flam. Liq. 2 Flammable liquids Category 2
------Flam. Liq. 3 Flammable liquids Category 3
------Skin Irrit. 2 Skin corrosion/irritation Category 2
------H225 Highly flammable liquid and vapor
------H226 Flammable liquid and vapor
------H315 Causes skin irritation
------H319 Causes serious eye irritation
------H332 Harmful if inhaled
------H351 Suspected of causing cancer
NFPA health hazard :2-Intense or continued exposure could cause temporary
incapacitation or possible residual injury unless prompt
medical attention is given.
NFPA fire hazard :3-Liquids and solids that can be ignited under almost all
ambient conditions.
NFPA reactivity :2-Normally unstable and readily undergo violent
decomposition but do not detonate. Also: may react
violently with water or may form potentially explosive
mixtures with water.
HMIS III Rating
Health :2 Moderate Hazard-Temporary or minor injury may occur
Flammability :3 Serious Hazard
Physical :1 Slight Hazard
Personal Protection :H
SDS US (GHS HazCom 2012)
To the best of our knowledge this SDS is accurate. The the extent allowed by law, this statement is made in lieu of an other warranties, expressed or implied including but not limited to any implied
warranty of merchantability or fitness for a particular purpose and is in lieu of any otherobligations or liability on the part of Dura Technoligies, Inc.
by | Sep 27, 2025
INDEX
CR30MI
CR30MICG
CR30MICQ
CR30MIF
CR30MIG
CR30MIQ
Composite Resource Marine ISO Laminating Resin
Safety Data SheetCR30MIMarine ISO
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
Date of issue:11/11/2014 Revision date: Supersedes: Version:1.0
11/11/2014 EN(English) SDS ID:CR30MI Page 1
SECTION 1:Identification of the substance/mixture and of the company/undertaking
1.1. Product identifier
Product form :Mixture liquidresin
Trade name :Composite Resource Marine ISO Laminating Resin
CAS No :Mixture
Product code :CR30MICP,CR30MICQ,CR30MIG, CR30MIF
Other means of identification :DISTRIBUTED BY REVCHEM COMPOSITES, INC.
1.2. Relevant identified uses of the substance or mixture and uses advised against
Use of the substance/mixture :Marine ISO Laminating Resin
1.3. Details of the supplier of the safetydata sheet
Composite Resources is supplied by Revchem Composites. 2720 South Willow Ave., Bloomington, CA 92316 1-800-281-4975
1.4. Emergency telephone number
Emergency number :800.424.9300
CHEMTREC: 1-800-424-9300
SECTION 2:Hazards identification
2.1. Classification of the substance or mixture
GHS-US classification
Flam. Liq. 1H224
2.2. Label elements
GHS-US labelling
Hazard pictograms (GHS-US) :
GHS02
Signal word (GHS-US) :Danger
Hazard statements (GHS-US) :H224-Extremely flammable liquid and vapour
Precautionary statements (GHS-US) :P210-Keep away from sparks.-No smoking
P233-Keep container tightly closed
P240-Ground/bond container and receiving equipment
P241-Use explosion-proof electrical equipment
P242-Use onlynon-sparking tools
P243-Take precautionary measures against static discharge
P280-Wear protective clothing
P303+P361+P353-IF ON SKIN (or hair): Remove/Take off immediately all contaminated
clothing. Rinse skin with water/shower
P370+P378-In case of fire: Use carbon dioxide (CO2), dry chemical powder, foam for
extinction
P403+P235-Store in a well-ventilated place. Keep cool
P501-Dispose of contents/container to …
2.3. Other hazards
No additional information available
2.4. Unknown acute toxicity (GHS-US)
No data available
SECTION 3:Composition/information on ingredients
3.1. Substance
Not applicable
Full text of H-phrases: see section 16
3.2. Mixture
Composite Resource Marine ISO Laminating Resin
Safety Data SheetCR30MIMarine ISO
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
11/11/2014 EN(English) SDS ID:CR30MI 2/7
Name Product identifier % GHS-US classification
Unsaturated Polyester Resin (CAS No)TRADE SECRET 53.5-53.5 Not classified
Styrene, inhibited (CAS No)100-42-5 <= 46.9 Flam. Liq. 3, H226
Acute Tox. 4 (Inhalation:vapour),
H332
Skin Irrit. 2, H315
Eye Irrit. 2A, H319
Carc. 2, H351
SECTION 4:First aid measures
4.1. Description of first aid measures
First-aid measures general :Never give anything by mouth to an unconscious person. If you feel unwell, seek medical advice
(show the label where possible).
First-aid measures after inhalation :Assure fresh air breathing. Allow the victim torest.
First-aid measures after skin contact :Remove affected clothing and wash all exposed skin area with mild soap and water, followed by
warm water rinse.
First-aid measures after eye contact :Rinse immediately with plenty of water. Obtain medical attention if pain, blinking or redness
persist.
First-aid measures after ingestion :Rinse mouth. Do NOT induce vomiting. Obtain emergency medical attention.
4.2. Most important symptoms and effects, both acute and delayed
Symptoms/injuries :Not expectedto present a significant hazard under anticipated conditions of normal use.
4.3. Indication of any immediate medical attention and special treatment needed
No additional information available
SECTION 5:Firefighting measures
5.1. Extinguishing media
Suitable extinguishing media :Foam. Dry powder. Carbon dioxide. Water spray. Sand.
Unsuitable extinguishing media :Do not use a heavy water stream.
5.2. Special hazards arising from the substance or mixture
No additional information available
5.3. Advice for firefighters
Firefighting instructions :Use water spray or fog for cooling exposed containers. Exercise caution when fighting any
chemical fire. Avoid (reject) fire-fighting water to enter environment.
Protection during firefighting :Do not enterfire area without proper protective equipment, including respiratory protection.
SECTION 6:Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
6.1.1.For non-emergency personnel
Emergency procedures :Evacuate unnecessary personnel.
6.1.2.For emergency responders
Protective equipment :Equip cleanup crew with proper protection.
Emergency procedures :Ventilate area.
6.2. Environmental precautions
Prevent entry to sewers and public waters. Notify authorities if liquid enters sewers or public waters.
6.3. Methods and material for containment and cleaning up
Methods for cleaning up :Soak up spills with inert solids, such as clay or diatomaceous earth as soon as possible. Collect
spillage. Store away from other materials.
6.4. Reference to other sections
See Heading 8. Exposure controls and personal protection.
SECTION 7:Handling and storage
7.1. Precautions for safe handling
Precautions for safe handling :Wash hands and other exposed areas with mild soap and water before eat, drink or smoke and
when leaving work. Provide good ventilation in process area to prevent formation of vapour.
Composite Resource Marine ISO Laminating Resin
Safety Data SheetCR30MIMarine ISO
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
11/11/2014 EN(English) SDS ID:CR30MI 3/7
7.2. Conditions for safe storage, including any incompatibilities
Storage conditions :Keep only in the original container in a cool, well ventilated place away from : Heat sources.
Keep container closed when not in use.
Incompatible products :Strong bases. strong acids.
Incompatible materials :Sources of ignition. Direct sunlight.
7.3. Specific end use(s)
No additional information available
SECTION 8:Exposure controls/personal protection
8.1. Control parameters
styrene, inhibited (100-42-5)
USA ACGIH ACGIH TWA (ppm) 20 ppm
USA ACGIH ACGIH STEL (ppm) 40 ppm
8.2. Exposure controls
Personal protective equipment :Avoid all unnecessary exposure.
Hand protection :Wear protective gloves.
Eye protection :Chemical goggles or safety glasses.
Respiratory protection :Wear approved mask.
Other information :When using, do not eat, drink or smoke.
SECTION 9:Physical and chemical properties
9.1. Information on basic physical and chemical properties
Physical state :Liquid
Appearance :Clear, colorless liquid
Colour :Clear
Odour :Characteristic
Odour threshold :No data available
pH :No dataavailable
Relative evaporation rate (butylacetate=1):No data available
Relative evaporation rate (ether=1) :< 1 slower than ether
Melting point :No data available
Freezing point :No data available
Boiling point :145.22 CInitial BoilingPoint for Styrene @ 760.00 mm HG(293.4 F)
Flash point :31.1 CFor Volatile Component (88 F)
Auto-ignition temperature :No data available
Decomposition temperature :No data available
Flammability (solid, gas) :No data available
Vapour pressure :4.3 mm HgVapor pressurefor Styrene20 C(68 F)
Relative vapour density at 20 C :3.6 (Air = 1)
Relative density :1.01-1.30Relative Density @25 C(77 F)
Solubility :No data available
Log Pow :No data available
Log Kow :No data available
Viscosity, kinematic :No data available
Viscosity, dynamic :No data available
Explosive properties :No data available
Oxidising properties :No data available
Explosive limits :No data available
9.2. Other information
No additional information available
Composite Resource Marine ISO Laminating Resin
Safety Data SheetCR30MIMarine ISO
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
11/11/2014 EN(English) SDS ID:CR30MI 4/7
SECTION 10:Stability and reactivity
10.1.Reactivity
No additional information available
10.2.Chemical stability
Stable under normal conditions. Not established.
10.3.Possibility of hazardous reactions
Not established.
10.4.Conditions to avoid
Direct sunlight. Extremely high or low temperatures.
10.5.Incompatible materials
strong acids. Strong bases.
10.6.Hazardous decomposition products
fume. Carbon monoxide. Carbon dioxide.
SECTION 11:Toxicological information
11.1.Information on toxicological effects
Acute toxicity :Not classified
styrene, inhibited (100-42-5)
LD50 oral rat 5000 mg/kg (>6000 mg/kg bodyweight; Rat; Rat)
LD50 dermal rat 2820 mg/kg (>2000 mg/kg bodyweight; Rat; Rat; Experimental value)
LD50 dermal rabbit 5010 mg/kg (Rabbit)
LC50 inhalation rat (mg/l) 12 mg/l/4h (Rat)
LC50 inhalation rat (ppm) 2770 ppm/4h (Rat)
ATE CLP (oral) 5000.000 mg/kg bodyweight
ATE CLP (dermal) 2820.000 mg/kg bodyweight
ATE CLP (gases) 2770.000 ppmv/4h
ATE CLP (vapours) 12.000 mg/l/4h
ATE CLP (dust,mist) 12.000 mg/l/4h
Skin corrosion/irritation :Not classified
Serious eye damage/irritation :Not classified
Respiratory or skin sensitisation :Not classified
Germ cell mutagenicity :Notclassified
Based on available data, the classification criteria are not met
Carcinogenicity :Not classified
styrene, inhibited (100-42-5)
IARC group 2B-Possibly Carcinogenic to Humans
Reproductive toxicity :Not classified
Based on available data, the classification criteria are not met
Specific target organ toxicity (single exposure):Not classified
Specific target organ toxicity (repeated
exposure)
:Not classified
Based on available data, the classification criteria are not met
Aspiration hazard :Not classified
Based on available data, the classification criteria are not met
Potential Adverse human health effects and
symptoms
:Based on available data, the classification criteria are not met.
Likely routes of exposure :Inhalation
SECTION 12:Ecological information
12.1.Toxicity
Composite Resource Marine ISO Laminating Resin
Safety Data SheetCR30MIMarine ISO
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
11/11/2014 EN(English) SDS ID:CR30MI 5/7
styrene, inhibited (100-42-5)
LC50 fishes 1 25 mg/l (96 h; Lepomis macrochirus)
LC50 other aquatic organisms 1 10-100 mg/l (96 h)
EC50 Daphnia 1 23 mg/l (48 h; Daphnia magna; LOCOMOTOR EFFECT)
LC50 fish 2 32 mg/l (96 h; Pimephales promelas)
EC50 Daphnia 2 27 mg/l (24 h; Daphnia magna)
TLM fish 1 25.1 mg/l (96 h; Lepomis macrochirus; SOFT WATER)
TLM fish 2 46.4 mg/l (96 h; Pimephales promelas; SOFT WATER)
TLM other aquatic organisms 1 10-100,96 h
Threshold limit other aquatic organisms 110-100,96 h; Pseudomonas putida
Threshold limit other aquatic organisms 272 mg/l
Threshold limit algae 1 > 200 mg/l (192 h; Scenedesmus quadricauda; INHIBITORY)
Threshold limit algae 2 67 mg/l (Microcystis aeruginosa; INHIBITORY)
12.2.Persistence and degradability
Composite Resource Marine ISO Laminating Resin(Mixture)
Persistence and degradability Not established.
styrene, inhibited (100-42-5)
Persistence and degradability Readily biodegradable in water. Not readily biodegradable in water. Forming sediments in
water. Non degradable in the soil. Adsorbs into the soil. Photodegradation in the air. Not
established.
Chemical oxygen demand (COD) 2.80 g O /g substance
ThOD 3.07 g O /g substance
BOD (% of ThOD) 0.42 % ThOD
Unsaturated Polyester Resin (TRADE SECRET)
Persistence and degradability Not established.
12.3.Bioaccumulative potential
Composite Resource Marine ISO Laminating Resin(Mixture)
Bioaccumulative potential Not established.
styrene, inhibited (100-42-5)
BCF fish 1 12-77 (QSAR)
BCF fish 2 35.5 (Carassius auratus)
Log Pow 2.95-3.16 (Experimental value)
Bioaccumulative potential Low potential for bioaccumulation (BCF < 500). Not established.
Unsaturated PolyesterResin (TRADE SECRET)
Bioaccumulative potential Not established.
12.4.Mobility in soil
styrene, inhibited (100-42-5)
Surface tension 0.032 N/m (19 C)
12.5.Other adverse effects
Other information :Avoid release to the environment.
SECTION 13:Disposal considerations
13.1.Waste treatment methods
Waste disposal recommendations :Dispose in a safe manner in accordance with local/national regulations.
Ecology-waste materials :Avoid release to the environment.
SECTION 14:Transport information
In accordance with DOT
UN-No.(DOT) :UN1866
DOT Proper Shipping Name :RESIN SOLUTION
Department of Transportation (DOT) Hazard
Classes
:3-Class 3-Flammable and combustible liquid 49 CFR 173.120
Composite Resource Marine ISO Laminating Resin
Safety Data SheetCR30MIMarine ISO
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
11/11/2014 EN(English) SDS ID:CR30MI 6/7
Hazard labels (DOT) :3-Flammable liquid
Packing group (DOT) :III-Minor Danger
Additional information
Other information :No supplementary information available.
ADR
Transport document description :UN UN1866 RESIN SOLUTION, III
Packing group (ADR) :III
Transport by sea
No additional information available
Air transport
No additional information available
SECTION 15:Regulatory information
15.1. US Federal regulations
Composite Resource Marine ISO Laminating Resin (Mixture)
RQ (Reportable quantity, section 304 of EPA's
List of Lists) :
1000 lb
styrene, inhibited (100-42-5)
RQ (Reportable quantity, section 304 of EPA's
List of Lists) :
1000 lb
SARA Section 311/312 Hazard Classes Immediate (acute) health hazard
Reactive hazard
Fire hazard
Delayed (chronic) health hazard
15.2. International regulations
CANADA
No additional information available
EU-Regulations
No additional information available
Classification according to Regulation (EC) No. 1272/2008 [CLP]
Not classified
Classification according to Directive 67/548/EEC or 1999/45/EC
Not classified
15.2.2.National regulations
styrene, inhibited (100-42-5)
Listed on EPA's Hazardous Air Pollutants (HAPS)
15.3. US State regulations
styrene, inhibited (100-42-5)
U.S.-California-
Proposition 65-
Carcinogens List
U.S.-California-
Proposition 65-
Developmental Toxicity
U.S.-California-
Proposition 65-
Reproductive Toxicity-
U.S.-California-
Proposition 65-
Reproductive Toxicity-Male
No significance risk level
(NSRL)
Composite Resource Marine ISO Laminating Resin
Safety Data SheetCR30MIMarine ISO
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
11/11/2014 EN(English) SDS ID:CR30MI 7/7
styrene, inhibited (100-42-5)
Female
styrene, inhibited (100-42-5)
U.S.-Massachusetts-Right To Know List
U.S.-New Jersey-Right to Know Hazardous Substance List
U.S.-Pennsylvania-RTK (Right to Know)-Environmental Hazard List
SECTION 16:Other information
Data sources :REGULATION (EC) No 1272/2008 OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 16 December 2008 on classification, labelling and packaging of substances and
mixtures, amending and repealing Directives 67/548/EEC and 1999/45/EC, and amending
Regulation (EC) No 1907/2006.
Other information :None.
Full text of H-phrases: see section 16:
------Acute Tox. 4 (Inhalation:vapour) Acute toxicity (inhalation:vapour) Category 4
------Carc. 2 Carcinogenicity, Category 2
------Eye Irrit. 2A Serious eye damage/eye irritation, Category 2A
------Flam. Liq. 1 Flammable liquids, Category 1
------Flam. Liq. 3 Flammable liquids, Category 3
------Skin Irrit. 2 Skin corrosion/irritation, Category 2
------H224 Extremely flammable liquid and vapour
------H226 Flammable liquid and vapour
------H315 Causes skin irritation
------H319 Causes serious eye irritation
------H332 Harmful if inhaled
------H351 Suspected of causing cancer
SDS US (GHS HazCom 2012)
To the best of our knowledge this SDS is accurate. The the extent allowed by law, this statement is made in lieu of an other warranties, expressed or implied including but not limited to any implied
warranty of merchantability or fitness for a particular purpose and is in lieu of any other obligations or liability on the part of Dura Technoligies, Inc.
by | Sep 27, 2025
INDEX
CR30MI
CR30MICG
CR30MICQ
CR30MIF
CR30MIG
CR30MIQ
Composite Resource Marine ISO Laminating Resin
Safety Data SheetCR30MIMarine ISO
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
Date of issue:11/11/2014 Revision date: Supersedes: Version:1.0
11/11/2014 EN(English) SDS ID:CR30MI Page 1
SECTION 1:Identification of the substance/mixture and of the company/undertaking
1.1. Product identifier
Product form :Mixture liquidresin
Trade name :Composite Resource Marine ISO Laminating Resin
CAS No :Mixture
Product code :CR30MICP,CR30MICQ,CR30MIG, CR30MIF
Other means of identification :DISTRIBUTED BY REVCHEM COMPOSITES, INC.
1.2. Relevant identified uses of the substance or mixture and uses advised against
Use of the substance/mixture :Marine ISO Laminating Resin
1.3. Details of the supplier of the safetydata sheet
Composite Resources is supplied by Revchem Composites. 2720 South Willow Ave., Bloomington, CA 92316 1-800-281-4975
1.4. Emergency telephone number
Emergency number :800.424.9300
CHEMTREC: 1-800-424-9300
SECTION 2:Hazards identification
2.1. Classification of the substance or mixture
GHS-US classification
Flam. Liq. 1H224
2.2. Label elements
GHS-US labelling
Hazard pictograms (GHS-US) :
GHS02
Signal word (GHS-US) :Danger
Hazard statements (GHS-US) :H224-Extremely flammable liquid and vapour
Precautionary statements (GHS-US) :P210-Keep away from sparks.-No smoking
P233-Keep container tightly closed
P240-Ground/bond container and receiving equipment
P241-Use explosion-proof electrical equipment
P242-Use onlynon-sparking tools
P243-Take precautionary measures against static discharge
P280-Wear protective clothing
P303+P361+P353-IF ON SKIN (or hair): Remove/Take off immediately all contaminated
clothing. Rinse skin with water/shower
P370+P378-In case of fire: Use carbon dioxide (CO2), dry chemical powder, foam for
extinction
P403+P235-Store in a well-ventilated place. Keep cool
P501-Dispose of contents/container to …
2.3. Other hazards
No additional information available
2.4. Unknown acute toxicity (GHS-US)
No data available
SECTION 3:Composition/information on ingredients
3.1. Substance
Not applicable
Full text of H-phrases: see section 16
3.2. Mixture
Composite Resource Marine ISO Laminating Resin
Safety Data SheetCR30MIMarine ISO
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
11/11/2014 EN(English) SDS ID:CR30MI 2/7
Name Product identifier % GHS-US classification
Unsaturated Polyester Resin (CAS No)TRADE SECRET 53.5-53.5 Not classified
Styrene, inhibited (CAS No)100-42-5 <= 46.9 Flam. Liq. 3, H226
Acute Tox. 4 (Inhalation:vapour),
H332
Skin Irrit. 2, H315
Eye Irrit. 2A, H319
Carc. 2, H351
SECTION 4:First aid measures
4.1. Description of first aid measures
First-aid measures general :Never give anything by mouth to an unconscious person. If you feel unwell, seek medical advice
(show the label where possible).
First-aid measures after inhalation :Assure fresh air breathing. Allow the victim torest.
First-aid measures after skin contact :Remove affected clothing and wash all exposed skin area with mild soap and water, followed by
warm water rinse.
First-aid measures after eye contact :Rinse immediately with plenty of water. Obtain medical attention if pain, blinking or redness
persist.
First-aid measures after ingestion :Rinse mouth. Do NOT induce vomiting. Obtain emergency medical attention.
4.2. Most important symptoms and effects, both acute and delayed
Symptoms/injuries :Not expectedto present a significant hazard under anticipated conditions of normal use.
4.3. Indication of any immediate medical attention and special treatment needed
No additional information available
SECTION 5:Firefighting measures
5.1. Extinguishing media
Suitable extinguishing media :Foam. Dry powder. Carbon dioxide. Water spray. Sand.
Unsuitable extinguishing media :Do not use a heavy water stream.
5.2. Special hazards arising from the substance or mixture
No additional information available
5.3. Advice for firefighters
Firefighting instructions :Use water spray or fog for cooling exposed containers. Exercise caution when fighting any
chemical fire. Avoid (reject) fire-fighting water to enter environment.
Protection during firefighting :Do not enterfire area without proper protective equipment, including respiratory protection.
SECTION 6:Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
6.1.1.For non-emergency personnel
Emergency procedures :Evacuate unnecessary personnel.
6.1.2.For emergency responders
Protective equipment :Equip cleanup crew with proper protection.
Emergency procedures :Ventilate area.
6.2. Environmental precautions
Prevent entry to sewers and public waters. Notify authorities if liquid enters sewers or public waters.
6.3. Methods and material for containment and cleaning up
Methods for cleaning up :Soak up spills with inert solids, such as clay or diatomaceous earth as soon as possible. Collect
spillage. Store away from other materials.
6.4. Reference to other sections
See Heading 8. Exposure controls and personal protection.
SECTION 7:Handling and storage
7.1. Precautions for safe handling
Precautions for safe handling :Wash hands and other exposed areas with mild soap and water before eat, drink or smoke and
when leaving work. Provide good ventilation in process area to prevent formation of vapour.
Composite Resource Marine ISO Laminating Resin
Safety Data SheetCR30MIMarine ISO
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
11/11/2014 EN(English) SDS ID:CR30MI 3/7
7.2. Conditions for safe storage, including any incompatibilities
Storage conditions :Keep only in the original container in a cool, well ventilated place away from : Heat sources.
Keep container closed when not in use.
Incompatible products :Strong bases. strong acids.
Incompatible materials :Sources of ignition. Direct sunlight.
7.3. Specific end use(s)
No additional information available
SECTION 8:Exposure controls/personal protection
8.1. Control parameters
styrene, inhibited (100-42-5)
USA ACGIH ACGIH TWA (ppm) 20 ppm
USA ACGIH ACGIH STEL (ppm) 40 ppm
8.2. Exposure controls
Personal protective equipment :Avoid all unnecessary exposure.
Hand protection :Wear protective gloves.
Eye protection :Chemical goggles or safety glasses.
Respiratory protection :Wear approved mask.
Other information :When using, do not eat, drink or smoke.
SECTION 9:Physical and chemical properties
9.1. Information on basic physical and chemical properties
Physical state :Liquid
Appearance :Clear, colorless liquid
Colour :Clear
Odour :Characteristic
Odour threshold :No data available
pH :No dataavailable
Relative evaporation rate (butylacetate=1):No data available
Relative evaporation rate (ether=1) :< 1 slower than ether
Melting point :No data available
Freezing point :No data available
Boiling point :145.22 CInitial BoilingPoint for Styrene @ 760.00 mm HG(293.4 F)
Flash point :31.1 CFor Volatile Component (88 F)
Auto-ignition temperature :No data available
Decomposition temperature :No data available
Flammability (solid, gas) :No data available
Vapour pressure :4.3 mm HgVapor pressurefor Styrene20 C(68 F)
Relative vapour density at 20 C :3.6 (Air = 1)
Relative density :1.01-1.30Relative Density @25 C(77 F)
Solubility :No data available
Log Pow :No data available
Log Kow :No data available
Viscosity, kinematic :No data available
Viscosity, dynamic :No data available
Explosive properties :No data available
Oxidising properties :No data available
Explosive limits :No data available
9.2. Other information
No additional information available
Composite Resource Marine ISO Laminating Resin
Safety Data SheetCR30MIMarine ISO
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
11/11/2014 EN(English) SDS ID:CR30MI 4/7
SECTION 10:Stability and reactivity
10.1.Reactivity
No additional information available
10.2.Chemical stability
Stable under normal conditions. Not established.
10.3.Possibility of hazardous reactions
Not established.
10.4.Conditions to avoid
Direct sunlight. Extremely high or low temperatures.
10.5.Incompatible materials
strong acids. Strong bases.
10.6.Hazardous decomposition products
fume. Carbon monoxide. Carbon dioxide.
SECTION 11:Toxicological information
11.1.Information on toxicological effects
Acute toxicity :Not classified
styrene, inhibited (100-42-5)
LD50 oral rat 5000 mg/kg (>6000 mg/kg bodyweight; Rat; Rat)
LD50 dermal rat 2820 mg/kg (>2000 mg/kg bodyweight; Rat; Rat; Experimental value)
LD50 dermal rabbit 5010 mg/kg (Rabbit)
LC50 inhalation rat (mg/l) 12 mg/l/4h (Rat)
LC50 inhalation rat (ppm) 2770 ppm/4h (Rat)
ATE CLP (oral) 5000.000 mg/kg bodyweight
ATE CLP (dermal) 2820.000 mg/kg bodyweight
ATE CLP (gases) 2770.000 ppmv/4h
ATE CLP (vapours) 12.000 mg/l/4h
ATE CLP (dust,mist) 12.000 mg/l/4h
Skin corrosion/irritation :Not classified
Serious eye damage/irritation :Not classified
Respiratory or skin sensitisation :Not classified
Germ cell mutagenicity :Notclassified
Based on available data, the classification criteria are not met
Carcinogenicity :Not classified
styrene, inhibited (100-42-5)
IARC group 2B-Possibly Carcinogenic to Humans
Reproductive toxicity :Not classified
Based on available data, the classification criteria are not met
Specific target organ toxicity (single exposure):Not classified
Specific target organ toxicity (repeated
exposure)
:Not classified
Based on available data, the classification criteria are not met
Aspiration hazard :Not classified
Based on available data, the classification criteria are not met
Potential Adverse human health effects and
symptoms
:Based on available data, the classification criteria are not met.
Likely routes of exposure :Inhalation
SECTION 12:Ecological information
12.1.Toxicity
Composite Resource Marine ISO Laminating Resin
Safety Data SheetCR30MIMarine ISO
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
11/11/2014 EN(English) SDS ID:CR30MI 5/7
styrene, inhibited (100-42-5)
LC50 fishes 1 25 mg/l (96 h; Lepomis macrochirus)
LC50 other aquatic organisms 1 10-100 mg/l (96 h)
EC50 Daphnia 1 23 mg/l (48 h; Daphnia magna; LOCOMOTOR EFFECT)
LC50 fish 2 32 mg/l (96 h; Pimephales promelas)
EC50 Daphnia 2 27 mg/l (24 h; Daphnia magna)
TLM fish 1 25.1 mg/l (96 h; Lepomis macrochirus; SOFT WATER)
TLM fish 2 46.4 mg/l (96 h; Pimephales promelas; SOFT WATER)
TLM other aquatic organisms 1 10-100,96 h
Threshold limit other aquatic organisms 110-100,96 h; Pseudomonas putida
Threshold limit other aquatic organisms 272 mg/l
Threshold limit algae 1 > 200 mg/l (192 h; Scenedesmus quadricauda; INHIBITORY)
Threshold limit algae 2 67 mg/l (Microcystis aeruginosa; INHIBITORY)
12.2.Persistence and degradability
Composite Resource Marine ISO Laminating Resin(Mixture)
Persistence and degradability Not established.
styrene, inhibited (100-42-5)
Persistence and degradability Readily biodegradable in water. Not readily biodegradable in water. Forming sediments in
water. Non degradable in the soil. Adsorbs into the soil. Photodegradation in the air. Not
established.
Chemical oxygen demand (COD) 2.80 g O /g substance
ThOD 3.07 g O /g substance
BOD (% of ThOD) 0.42 % ThOD
Unsaturated Polyester Resin (TRADE SECRET)
Persistence and degradability Not established.
12.3.Bioaccumulative potential
Composite Resource Marine ISO Laminating Resin(Mixture)
Bioaccumulative potential Not established.
styrene, inhibited (100-42-5)
BCF fish 1 12-77 (QSAR)
BCF fish 2 35.5 (Carassius auratus)
Log Pow 2.95-3.16 (Experimental value)
Bioaccumulative potential Low potential for bioaccumulation (BCF < 500). Not established.
Unsaturated PolyesterResin (TRADE SECRET)
Bioaccumulative potential Not established.
12.4.Mobility in soil
styrene, inhibited (100-42-5)
Surface tension 0.032 N/m (19 C)
12.5.Other adverse effects
Other information :Avoid release to the environment.
SECTION 13:Disposal considerations
13.1.Waste treatment methods
Waste disposal recommendations :Dispose in a safe manner in accordance with local/national regulations.
Ecology-waste materials :Avoid release to the environment.
SECTION 14:Transport information
In accordance with DOT
UN-No.(DOT) :UN1866
DOT Proper Shipping Name :RESIN SOLUTION
Department of Transportation (DOT) Hazard
Classes
:3-Class 3-Flammable and combustible liquid 49 CFR 173.120
Composite Resource Marine ISO Laminating Resin
Safety Data SheetCR30MIMarine ISO
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
11/11/2014 EN(English) SDS ID:CR30MI 6/7
Hazard labels (DOT) :3-Flammable liquid
Packing group (DOT) :III-Minor Danger
Additional information
Other information :No supplementary information available.
ADR
Transport document description :UN UN1866 RESIN SOLUTION, III
Packing group (ADR) :III
Transport by sea
No additional information available
Air transport
No additional information available
SECTION 15:Regulatory information
15.1. US Federal regulations
Composite Resource Marine ISO Laminating Resin (Mixture)
RQ (Reportable quantity, section 304 of EPA's
List of Lists) :
1000 lb
styrene, inhibited (100-42-5)
RQ (Reportable quantity, section 304 of EPA's
List of Lists) :
1000 lb
SARA Section 311/312 Hazard Classes Immediate (acute) health hazard
Reactive hazard
Fire hazard
Delayed (chronic) health hazard
15.2. International regulations
CANADA
No additional information available
EU-Regulations
No additional information available
Classification according to Regulation (EC) No. 1272/2008 [CLP]
Not classified
Classification according to Directive 67/548/EEC or 1999/45/EC
Not classified
15.2.2.National regulations
styrene, inhibited (100-42-5)
Listed on EPA's Hazardous Air Pollutants (HAPS)
15.3. US State regulations
styrene, inhibited (100-42-5)
U.S.-California-
Proposition 65-
Carcinogens List
U.S.-California-
Proposition 65-
Developmental Toxicity
U.S.-California-
Proposition 65-
Reproductive Toxicity-
U.S.-California-
Proposition 65-
Reproductive Toxicity-Male
No significance risk level
(NSRL)
Composite Resource Marine ISO Laminating Resin
Safety Data SheetCR30MIMarine ISO
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
11/11/2014 EN(English) SDS ID:CR30MI 7/7
styrene, inhibited (100-42-5)
Female
styrene, inhibited (100-42-5)
U.S.-Massachusetts-Right To Know List
U.S.-New Jersey-Right to Know Hazardous Substance List
U.S.-Pennsylvania-RTK (Right to Know)-Environmental Hazard List
SECTION 16:Other information
Data sources :REGULATION (EC) No 1272/2008 OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 16 December 2008 on classification, labelling and packaging of substances and
mixtures, amending and repealing Directives 67/548/EEC and 1999/45/EC, and amending
Regulation (EC) No 1907/2006.
Other information :None.
Full text of H-phrases: see section 16:
------Acute Tox. 4 (Inhalation:vapour) Acute toxicity (inhalation:vapour) Category 4
------Carc. 2 Carcinogenicity, Category 2
------Eye Irrit. 2A Serious eye damage/eye irritation, Category 2A
------Flam. Liq. 1 Flammable liquids, Category 1
------Flam. Liq. 3 Flammable liquids, Category 3
------Skin Irrit. 2 Skin corrosion/irritation, Category 2
------H224 Extremely flammable liquid and vapour
------H226 Flammable liquid and vapour
------H315 Causes skin irritation
------H319 Causes serious eye irritation
------H332 Harmful if inhaled
------H351 Suspected of causing cancer
SDS US (GHS HazCom 2012)
To the best of our knowledge this SDS is accurate. The the extent allowed by law, this statement is made in lieu of an other warranties, expressed or implied including but not limited to any implied
warranty of merchantability or fitness for a particular purpose and is in lieu of any other obligations or liability on the part of Dura Technoligies, Inc.
by | Sep 27, 2025
INDEX
CR30MI
CR30MICG
CR30MICQ
CR30MIF
CR30MIG
CR30MIQ
Composite Resource Marine ISO Laminating Resin
Safety Data SheetCR30MIMarine ISO
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
Date of issue:11/11/2014 Revision date: Supersedes: Version:1.0
11/11/2014 EN(English) SDS ID:CR30MI Page 1
SECTION 1:Identification of the substance/mixture and of the company/undertaking
1.1. Product identifier
Product form :Mixture liquidresin
Trade name :Composite Resource Marine ISO Laminating Resin
CAS No :Mixture
Product code :CR30MICP,CR30MICQ,CR30MIG, CR30MIF
Other means of identification :DISTRIBUTED BY REVCHEM COMPOSITES, INC.
1.2. Relevant identified uses of the substance or mixture and uses advised against
Use of the substance/mixture :Marine ISO Laminating Resin
1.3. Details of the supplier of the safetydata sheet
Composite Resources is supplied by Revchem Composites. 2720 South Willow Ave., Bloomington, CA 92316 1-800-281-4975
1.4. Emergency telephone number
Emergency number :800.424.9300
CHEMTREC: 1-800-424-9300
SECTION 2:Hazards identification
2.1. Classification of the substance or mixture
GHS-US classification
Flam. Liq. 1H224
2.2. Label elements
GHS-US labelling
Hazard pictograms (GHS-US) :
GHS02
Signal word (GHS-US) :Danger
Hazard statements (GHS-US) :H224-Extremely flammable liquid and vapour
Precautionary statements (GHS-US) :P210-Keep away from sparks.-No smoking
P233-Keep container tightly closed
P240-Ground/bond container and receiving equipment
P241-Use explosion-proof electrical equipment
P242-Use onlynon-sparking tools
P243-Take precautionary measures against static discharge
P280-Wear protective clothing
P303+P361+P353-IF ON SKIN (or hair): Remove/Take off immediately all contaminated
clothing. Rinse skin with water/shower
P370+P378-In case of fire: Use carbon dioxide (CO2), dry chemical powder, foam for
extinction
P403+P235-Store in a well-ventilated place. Keep cool
P501-Dispose of contents/container to …
2.3. Other hazards
No additional information available
2.4. Unknown acute toxicity (GHS-US)
No data available
SECTION 3:Composition/information on ingredients
3.1. Substance
Not applicable
Full text of H-phrases: see section 16
3.2. Mixture
Composite Resource Marine ISO Laminating Resin
Safety Data SheetCR30MIMarine ISO
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
11/11/2014 EN(English) SDS ID:CR30MI 2/7
Name Product identifier % GHS-US classification
Unsaturated Polyester Resin (CAS No)TRADE SECRET 53.5-53.5 Not classified
Styrene, inhibited (CAS No)100-42-5 <= 46.9 Flam. Liq. 3, H226
Acute Tox. 4 (Inhalation:vapour),
H332
Skin Irrit. 2, H315
Eye Irrit. 2A, H319
Carc. 2, H351
SECTION 4:First aid measures
4.1. Description of first aid measures
First-aid measures general :Never give anything by mouth to an unconscious person. If you feel unwell, seek medical advice
(show the label where possible).
First-aid measures after inhalation :Assure fresh air breathing. Allow the victim torest.
First-aid measures after skin contact :Remove affected clothing and wash all exposed skin area with mild soap and water, followed by
warm water rinse.
First-aid measures after eye contact :Rinse immediately with plenty of water. Obtain medical attention if pain, blinking or redness
persist.
First-aid measures after ingestion :Rinse mouth. Do NOT induce vomiting. Obtain emergency medical attention.
4.2. Most important symptoms and effects, both acute and delayed
Symptoms/injuries :Not expectedto present a significant hazard under anticipated conditions of normal use.
4.3. Indication of any immediate medical attention and special treatment needed
No additional information available
SECTION 5:Firefighting measures
5.1. Extinguishing media
Suitable extinguishing media :Foam. Dry powder. Carbon dioxide. Water spray. Sand.
Unsuitable extinguishing media :Do not use a heavy water stream.
5.2. Special hazards arising from the substance or mixture
No additional information available
5.3. Advice for firefighters
Firefighting instructions :Use water spray or fog for cooling exposed containers. Exercise caution when fighting any
chemical fire. Avoid (reject) fire-fighting water to enter environment.
Protection during firefighting :Do not enterfire area without proper protective equipment, including respiratory protection.
SECTION 6:Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
6.1.1.For non-emergency personnel
Emergency procedures :Evacuate unnecessary personnel.
6.1.2.For emergency responders
Protective equipment :Equip cleanup crew with proper protection.
Emergency procedures :Ventilate area.
6.2. Environmental precautions
Prevent entry to sewers and public waters. Notify authorities if liquid enters sewers or public waters.
6.3. Methods and material for containment and cleaning up
Methods for cleaning up :Soak up spills with inert solids, such as clay or diatomaceous earth as soon as possible. Collect
spillage. Store away from other materials.
6.4. Reference to other sections
See Heading 8. Exposure controls and personal protection.
SECTION 7:Handling and storage
7.1. Precautions for safe handling
Precautions for safe handling :Wash hands and other exposed areas with mild soap and water before eat, drink or smoke and
when leaving work. Provide good ventilation in process area to prevent formation of vapour.
Composite Resource Marine ISO Laminating Resin
Safety Data SheetCR30MIMarine ISO
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
11/11/2014 EN(English) SDS ID:CR30MI 3/7
7.2. Conditions for safe storage, including any incompatibilities
Storage conditions :Keep only in the original container in a cool, well ventilated place away from : Heat sources.
Keep container closed when not in use.
Incompatible products :Strong bases. strong acids.
Incompatible materials :Sources of ignition. Direct sunlight.
7.3. Specific end use(s)
No additional information available
SECTION 8:Exposure controls/personal protection
8.1. Control parameters
styrene, inhibited (100-42-5)
USA ACGIH ACGIH TWA (ppm) 20 ppm
USA ACGIH ACGIH STEL (ppm) 40 ppm
8.2. Exposure controls
Personal protective equipment :Avoid all unnecessary exposure.
Hand protection :Wear protective gloves.
Eye protection :Chemical goggles or safety glasses.
Respiratory protection :Wear approved mask.
Other information :When using, do not eat, drink or smoke.
SECTION 9:Physical and chemical properties
9.1. Information on basic physical and chemical properties
Physical state :Liquid
Appearance :Clear, colorless liquid
Colour :Clear
Odour :Characteristic
Odour threshold :No data available
pH :No dataavailable
Relative evaporation rate (butylacetate=1):No data available
Relative evaporation rate (ether=1) :< 1 slower than ether
Melting point :No data available
Freezing point :No data available
Boiling point :145.22 CInitial BoilingPoint for Styrene @ 760.00 mm HG(293.4 F)
Flash point :31.1 CFor Volatile Component (88 F)
Auto-ignition temperature :No data available
Decomposition temperature :No data available
Flammability (solid, gas) :No data available
Vapour pressure :4.3 mm HgVapor pressurefor Styrene20 C(68 F)
Relative vapour density at 20 C :3.6 (Air = 1)
Relative density :1.01-1.30Relative Density @25 C(77 F)
Solubility :No data available
Log Pow :No data available
Log Kow :No data available
Viscosity, kinematic :No data available
Viscosity, dynamic :No data available
Explosive properties :No data available
Oxidising properties :No data available
Explosive limits :No data available
9.2. Other information
No additional information available
Composite Resource Marine ISO Laminating Resin
Safety Data SheetCR30MIMarine ISO
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
11/11/2014 EN(English) SDS ID:CR30MI 4/7
SECTION 10:Stability and reactivity
10.1.Reactivity
No additional information available
10.2.Chemical stability
Stable under normal conditions. Not established.
10.3.Possibility of hazardous reactions
Not established.
10.4.Conditions to avoid
Direct sunlight. Extremely high or low temperatures.
10.5.Incompatible materials
strong acids. Strong bases.
10.6.Hazardous decomposition products
fume. Carbon monoxide. Carbon dioxide.
SECTION 11:Toxicological information
11.1.Information on toxicological effects
Acute toxicity :Not classified
styrene, inhibited (100-42-5)
LD50 oral rat 5000 mg/kg (>6000 mg/kg bodyweight; Rat; Rat)
LD50 dermal rat 2820 mg/kg (>2000 mg/kg bodyweight; Rat; Rat; Experimental value)
LD50 dermal rabbit 5010 mg/kg (Rabbit)
LC50 inhalation rat (mg/l) 12 mg/l/4h (Rat)
LC50 inhalation rat (ppm) 2770 ppm/4h (Rat)
ATE CLP (oral) 5000.000 mg/kg bodyweight
ATE CLP (dermal) 2820.000 mg/kg bodyweight
ATE CLP (gases) 2770.000 ppmv/4h
ATE CLP (vapours) 12.000 mg/l/4h
ATE CLP (dust,mist) 12.000 mg/l/4h
Skin corrosion/irritation :Not classified
Serious eye damage/irritation :Not classified
Respiratory or skin sensitisation :Not classified
Germ cell mutagenicity :Notclassified
Based on available data, the classification criteria are not met
Carcinogenicity :Not classified
styrene, inhibited (100-42-5)
IARC group 2B-Possibly Carcinogenic to Humans
Reproductive toxicity :Not classified
Based on available data, the classification criteria are not met
Specific target organ toxicity (single exposure):Not classified
Specific target organ toxicity (repeated
exposure)
:Not classified
Based on available data, the classification criteria are not met
Aspiration hazard :Not classified
Based on available data, the classification criteria are not met
Potential Adverse human health effects and
symptoms
:Based on available data, the classification criteria are not met.
Likely routes of exposure :Inhalation
SECTION 12:Ecological information
12.1.Toxicity
Composite Resource Marine ISO Laminating Resin
Safety Data SheetCR30MIMarine ISO
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
11/11/2014 EN(English) SDS ID:CR30MI 5/7
styrene, inhibited (100-42-5)
LC50 fishes 1 25 mg/l (96 h; Lepomis macrochirus)
LC50 other aquatic organisms 1 10-100 mg/l (96 h)
EC50 Daphnia 1 23 mg/l (48 h; Daphnia magna; LOCOMOTOR EFFECT)
LC50 fish 2 32 mg/l (96 h; Pimephales promelas)
EC50 Daphnia 2 27 mg/l (24 h; Daphnia magna)
TLM fish 1 25.1 mg/l (96 h; Lepomis macrochirus; SOFT WATER)
TLM fish 2 46.4 mg/l (96 h; Pimephales promelas; SOFT WATER)
TLM other aquatic organisms 1 10-100,96 h
Threshold limit other aquatic organisms 110-100,96 h; Pseudomonas putida
Threshold limit other aquatic organisms 272 mg/l
Threshold limit algae 1 > 200 mg/l (192 h; Scenedesmus quadricauda; INHIBITORY)
Threshold limit algae 2 67 mg/l (Microcystis aeruginosa; INHIBITORY)
12.2.Persistence and degradability
Composite Resource Marine ISO Laminating Resin(Mixture)
Persistence and degradability Not established.
styrene, inhibited (100-42-5)
Persistence and degradability Readily biodegradable in water. Not readily biodegradable in water. Forming sediments in
water. Non degradable in the soil. Adsorbs into the soil. Photodegradation in the air. Not
established.
Chemical oxygen demand (COD) 2.80 g O /g substance
ThOD 3.07 g O /g substance
BOD (% of ThOD) 0.42 % ThOD
Unsaturated Polyester Resin (TRADE SECRET)
Persistence and degradability Not established.
12.3.Bioaccumulative potential
Composite Resource Marine ISO Laminating Resin(Mixture)
Bioaccumulative potential Not established.
styrene, inhibited (100-42-5)
BCF fish 1 12-77 (QSAR)
BCF fish 2 35.5 (Carassius auratus)
Log Pow 2.95-3.16 (Experimental value)
Bioaccumulative potential Low potential for bioaccumulation (BCF < 500). Not established.
Unsaturated PolyesterResin (TRADE SECRET)
Bioaccumulative potential Not established.
12.4.Mobility in soil
styrene, inhibited (100-42-5)
Surface tension 0.032 N/m (19 C)
12.5.Other adverse effects
Other information :Avoid release to the environment.
SECTION 13:Disposal considerations
13.1.Waste treatment methods
Waste disposal recommendations :Dispose in a safe manner in accordance with local/national regulations.
Ecology-waste materials :Avoid release to the environment.
SECTION 14:Transport information
In accordance with DOT
UN-No.(DOT) :UN1866
DOT Proper Shipping Name :RESIN SOLUTION
Department of Transportation (DOT) Hazard
Classes
:3-Class 3-Flammable and combustible liquid 49 CFR 173.120
Composite Resource Marine ISO Laminating Resin
Safety Data SheetCR30MIMarine ISO
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
11/11/2014 EN(English) SDS ID:CR30MI 6/7
Hazard labels (DOT) :3-Flammable liquid
Packing group (DOT) :III-Minor Danger
Additional information
Other information :No supplementary information available.
ADR
Transport document description :UN UN1866 RESIN SOLUTION, III
Packing group (ADR) :III
Transport by sea
No additional information available
Air transport
No additional information available
SECTION 15:Regulatory information
15.1. US Federal regulations
Composite Resource Marine ISO Laminating Resin (Mixture)
RQ (Reportable quantity, section 304 of EPA's
List of Lists) :
1000 lb
styrene, inhibited (100-42-5)
RQ (Reportable quantity, section 304 of EPA's
List of Lists) :
1000 lb
SARA Section 311/312 Hazard Classes Immediate (acute) health hazard
Reactive hazard
Fire hazard
Delayed (chronic) health hazard
15.2. International regulations
CANADA
No additional information available
EU-Regulations
No additional information available
Classification according to Regulation (EC) No. 1272/2008 [CLP]
Not classified
Classification according to Directive 67/548/EEC or 1999/45/EC
Not classified
15.2.2.National regulations
styrene, inhibited (100-42-5)
Listed on EPA's Hazardous Air Pollutants (HAPS)
15.3. US State regulations
styrene, inhibited (100-42-5)
U.S.-California-
Proposition 65-
Carcinogens List
U.S.-California-
Proposition 65-
Developmental Toxicity
U.S.-California-
Proposition 65-
Reproductive Toxicity-
U.S.-California-
Proposition 65-
Reproductive Toxicity-Male
No significance risk level
(NSRL)
Composite Resource Marine ISO Laminating Resin
Safety Data SheetCR30MIMarine ISO
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
11/11/2014 EN(English) SDS ID:CR30MI 7/7
styrene, inhibited (100-42-5)
Female
styrene, inhibited (100-42-5)
U.S.-Massachusetts-Right To Know List
U.S.-New Jersey-Right to Know Hazardous Substance List
U.S.-Pennsylvania-RTK (Right to Know)-Environmental Hazard List
SECTION 16:Other information
Data sources :REGULATION (EC) No 1272/2008 OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 16 December 2008 on classification, labelling and packaging of substances and
mixtures, amending and repealing Directives 67/548/EEC and 1999/45/EC, and amending
Regulation (EC) No 1907/2006.
Other information :None.
Full text of H-phrases: see section 16:
------Acute Tox. 4 (Inhalation:vapour) Acute toxicity (inhalation:vapour) Category 4
------Carc. 2 Carcinogenicity, Category 2
------Eye Irrit. 2A Serious eye damage/eye irritation, Category 2A
------Flam. Liq. 1 Flammable liquids, Category 1
------Flam. Liq. 3 Flammable liquids, Category 3
------Skin Irrit. 2 Skin corrosion/irritation, Category 2
------H224 Extremely flammable liquid and vapour
------H226 Flammable liquid and vapour
------H315 Causes skin irritation
------H319 Causes serious eye irritation
------H332 Harmful if inhaled
------H351 Suspected of causing cancer
SDS US (GHS HazCom 2012)
To the best of our knowledge this SDS is accurate. The the extent allowed by law, this statement is made in lieu of an other warranties, expressed or implied including but not limited to any implied
warranty of merchantability or fitness for a particular purpose and is in lieu of any other obligations or liability on the part of Dura Technoligies, Inc.
by | Sep 27, 2025
INDEX
CR3040CC
CR3040CCCG
CR3040CCCQ
CR3040CCG
CR3040CCQ
Composite Resource Clear Casting Resin
Safety Data SheetCR3040CC
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
Date of issue:12/17/2014 Revision date: Supersedes: Version:1.0
12/17/2014 EN(English) SDS ID:CR3040CC Page 1
SECTION 1:Identification of the substance/mixture and of the company/undertaking
1.1. Product identifier
Product form :Mixture
Trade name :Composite Resource Clear Casting Resin
CAS No :Mixture
Product code :CR3040CCCP,CR3040CCCQ,CR3040CCG , CR3040CCF
Other means of identification :DISTRIBUTED BY REVCHEM COMPOSITES, INC.
1.2. Relevant identified uses of the substance or mixture and uses advised against
Use of the substance/mixture :Clear Casting Resin
1.3. Details of the supplier of the safety data sheet
Composite Resources is supplied by Revchem Composites. 2720 South Willow Ave., Bloomington, CA 92316 1-800-281-4975
1.4. Emergency telephone number
Emergency number :800.424.9300
CHEMTREC: 1-800-424-9300
SECTION 2:Hazards identification
2.1. Classification of the substance or mixture
GHS-US classification
Flam. Liq. 3H226
Skin Irrit. 2H315
Eye Irrit. 2AH319
Carc. 2 H351
2.2. Label elements
GHS-US labelling
Hazard pictograms (GHS-US) :
GHS02 GHS07 GHS08
Signal word (GHS-US) :Warning
Hazard statements (GHS-US) :H226-Flammable liquid and vapour
H315-Causes skin irritation
H319-Causes serious eye irritation
H351-Suspected of causing cancer
Precautionary statements (GHS-US) :P201-Obtain special instructions before use
P202-Do not handle until all safety precautions have been read and understood
P210-Keep away from sparks.-No smoking
P233-Keep container tightly closed
P240-Ground/bond container and receiving equipment
P241-Use explosion-proof electrical equipment
P242-Use only non-sparking tools
P243-Take precautionary measures against static discharge
P264-Wash … thoroughly after handling
P280-Wear protective clothing
P302+P352-IF ON SKIN: Wash with plenty of soap and water
P303+P361+P353-IF ON SKIN (or hair): Remove/Take off immediately all contaminated
clothing. Rinse skin with water/shower
P305+P351+P338-If in eyes: Rinse cautiously with water for several minutes. Remove contact
lenses, if present and easy to do. Continue rinsing
P308+P313-IF exposed or concerned: Get medical advice/attention
P321-Specific treatment (see … on this label)
P332+P313-If skin irritation occurs: Get medical advice/attention
P337+P313-If eye irritation persists: Get medical advice/attention
P362-Take off contaminated clothing and wash before reuse
P370+P378-In case of fire: Use carbon dioxide (CO2), dry chemical powder, foam for
extinction
Composite Resource Clear Casting Resin
Safety Data SheetCR3040CC
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
12/17/2014 EN(English) SDS ID:CR3040CC 2/8
P403+P235-Store in a well-ventilated place. Keep cool
P405-Store locked up
P501-Dispose of contents/container to …
2.3. Other hazards
No additional information available
2.4. Unknown acute toxicity (GHS-US)
No data available
SECTION 3:Composition/information on ingredients
3.1. Substance
Not applicable
Full text of H-phrases: see section 16
3.2. Mixture
Name Product identifier % GHS-US classification
Unsaturated Polyester Resin (CAS No)TRADE SECRET 62-64 Not classified
Styrene, inhibited (CAS No)100-42-5 37 Flam. Liq. 3, H226
Acute Tox. 4 (Inhalation:vapour),
H332
Skin Irrit. 2, H315
Eye Irrit. 2A, H319
Carc. 2, H351
SECTION 4:First aid measures
4.1. Description of first aid measures
First-aid measures general :Never give anything by mouth to an unconscious person. If you feel unwell, seek medical advice
(show the label where possible). Suspected of causing cancer.
First-aid measures after inhalation :Assure fresh air breathing. Allow the victim to rest.
First-aid measures after skin contact :Rinse skin with water/shower. Remove/Take off immediately all contaminated clothing.Wash
with plenty of soap and water. Wash contaminated clothing before reuse. If skin irritation occurs:
Get medical advice/attention. Specific treatment (see … on this label).
First-aid measures after eye contact :Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to
do. Continue rinsing. If eye irritation persists: Get medical advice/attention.
First-aid measures after ingestion :Rinse mouth. Do NOT induce vomiting. Obtain emergency medical attention.
4.2. Most important symptoms and effects, both acute and delayed
Symptoms/injuries after skin contact :Causes skin irritation.
Symptoms/injuries after eye contact :Causes serious eye irritation.
4.3. Indication of any immediate medical attention and special treatment needed
No additional information available
SECTION 5:Firefighting measures
5.1. Extinguishing media
Suitable extinguishing media :Foam. Dry powder. Carbon dioxide. Water spray. Sand.
Unsuitable extinguishing media :Do not use a heavy waterstream.
5.2. Special hazards arising from the substance or mixture
Fire hazard :Extremely flammable liquid and vapour.
Explosion hazard :May form flammable/explosive vapour-air mixture.
5.3. Advice for firefighters
Firefighting instructions :Use water spray or fog for cooling exposed containers. Exercise caution when fighting any
chemical fire. Avoid (reject) fire-fighting water to enter environment.
Protection during firefighting :Do not enter fire area without proper protective equipment, including respiratory protection.
SECTION 6:Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
General measures :Remove ignition sources. Use special care to avoid static electric charges. No naked lights. No
smoking.
Composite Resource Clear Casting Resin
Safety Data SheetCR3040CC
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
12/17/2014 EN(English) SDS ID:CR3040CC 3/8
6.1.1.For non-emergency personnel
Emergency procedures :Evacuate unnecessary personnel.
6.1.2.For emergency responders
Protective equipment :Equip cleanup crew with proper protection.
Emergency procedures :Ventilate area.
6.2. Environmental precautions
Prevent entry to sewers and public waters. Notify authorities if liquid enters sewers or public waters.
6.3. Methods and material for containment and cleaning up
Methods for cleaning up :Soak up spills with inert solids, such as clay ordiatomaceous earth as soon as possible. Collect
spillage. Store away from other materials.
6.4. Reference to other sections
See Heading 8. Exposure controls and personal protection.
SECTION 7:Handling and storage
7.1. Precautions for safe handling
Additional hazards when processed :Handle empty containers with care because residual vapours are flammable.
Precautions for safe handling :Wash hands and other exposed areas with mild soap and water before eat, drink or smoke and
when leaving work. Provide good ventilation in process area to prevent formation of vapour. No
naked lights. No smoking. Take precautionary measures against static discharge. Use only non-
sparking tools. Obtain special instructions before use. Do not handle until all safety precautions
have been read and understood.
Hygiene measures :Wash … thoroughly after handling.
7.2. Conditions for safe storage, including any incompatibilities
Technical measures :Ground/bond container and receiving equipment. Use explosion-proof
electrical/ventilating/lighting/ equipment.
Storage conditions :Keep only in the original container in a cool, well ventilated place away from : Heat sources.
Keep in fireproof place. Keep container tightly closed.
Incompatible products :Strong bases. strongacids.
Incompatible materials :Sources of ignition. Direct sunlight. Heat sources.
7.3. Specific end use(s)
No additional information available
SECTION 8:Exposure controls/personal protection
8.1. Control parameters
styrene, inhibited (100-42-5)
USA ACGIH ACGIH TWA (ppm) 20 ppm
USA ACGIH ACGIH STEL (ppm) 40 ppm
8.2. Exposure controls
Personal protective equipment :Avoid all unnecessary exposure.
Hand protection :Wear protective gloves.
Eye protection :Chemical goggles or safety glasses.
Skin and body protection :Wear suitable protective clothing.
Respiratory protection :Wear approved mask.
Other information :When using, do not eat, drink or smoke.
SECTION 9:Physical and chemical properties
9.1. Information on basic physical and chemical properties
Physical state :Liquid
Appearance :Clear, colorless liquid
Colour :Clear
Odour :characteristic.
Odour threshold :No data available
pH :No data available
Relative evaporation rate (butylacetate=1):No data available
Composite Resource Clear Casting Resin
Safety Data SheetCR3040CC
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
12/17/2014 EN(English) SDS ID:CR3040CC 4/8
Relative evaporation rate (ether=1) :Slower than ether
Melting point :No data available
Freezing point :No data available
Boiling point :145.22 C Initial Boiling Point for Styrene @ 760.00 mm Hg(293.40 F)
Flash point :31.1 C for Volatile Component (88 F)
Auto-ignition temperature :No data available
Decomposition temperature :No data available
Flammability (solid, gas) :No data available
Vapour pressure :4.3 mm Hg Vapor pressure for Styrene at 20 C (68 F)
Relativevapour density at 20 C :3.6 (Air = 1)
Relative density :1-1.2 Relative Density @ 25 C (77 F)
Solubility :No data available
Log Pow :No data available
Log Kow :No data available
Viscosity, kinematic :No data available
Viscosity,dynamic :No data available
Explosive properties :No data available
Oxidising properties :No data available
Explosive limits :No data available
9.2. Other information
No additional information available
SECTION 10:Stability and reactivity
10.1.Reactivity
No additional information available
10.2.Chemical stability
Stable under normal conditions. Not established. Extremely flammable liquid and vapour. May form flammable/explosive vapour-air mixture.
10.3.Possibility of hazardous reactions
Not established.
10.4.Conditions to avoid
Direct sunlight. Extremely high or low temperatures. . Heat. Overheating. Open flame.
10.5.Incompatible materials
strong acids. Strong bases.
10.6.Hazardous decomposition products
fume. Carbon monoxide. Carbon dioxide. May release flammable gases.
SECTION 11:Toxicological information
11.1.Information on toxicological effects
Acute toxicity :Not classified
styrene, inhibited (100-42-5)
LD50 oral rat 5000 mg/kg (>6000 mg/kg bodyweight; Rat; Rat)
LD50 dermal rat 2820 mg/kg (>2000 mg/kg bodyweight; Rat; Rat; Experimental value)
LD50 dermal rabbit 5010 mg/kg (Rabbit)
LC50 inhalation rat (mg/l) 12 mg/l/4h (Rat)
LC50 inhalation rat (ppm) 2770 ppm/4h (Rat)
ATE CLP (oral) 5000.000 mg/kg bodyweight
ATE CLP (dermal) 2820.000 mg/kg bodyweight
ATE CLP (gases) 2770.000 ppmv/4h
ATE CLP (vapours) 12.000 mg/l/4h
ATE CLP (dust,mist) 12.000 mg/l/4h
Skin corrosion/irritation :Causes skin irritation.
Composite Resource Clear Casting Resin
Safety Data SheetCR3040CC
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
12/17/2014 EN(English) SDS ID:CR3040CC 5/8
Serious eye damage/irritation :Causes serious eye irritation.
Respiratory or skin sensitisation :Not classified
Germ cell mutagenicity :Not classified
Based on available data, the classification criteria are not met
Carcinogenicity :Suspected of causing cancer.
styrene, inhibited (100-42-5)
IARC group 2B-Possibly Carcinogenic to Humans
Reproductive toxicity :Not classified
Based on available data, the classification criteria are not met
Specific target organ toxicity (single exposure):Not classified
Specific target organ toxicity (repeated
exposure)
:Not classified
Based on available data, the classification criteria are not met
Aspiration hazard :Not classified
Based on available data, the classification criteria are not met
Potential Adverse human health effects and
symptoms
:Based on available data, the classification criteria are not met.
Symptoms/injuries after skin contact :Causes skin irritation.
Symptoms/injuries after eye contact :Causes serious eye irritation.
Likely routes of exposure :Inhalation
SECTION 12:Ecological information
12.1.Toxicity
styrene, inhibited (100-42-5)
LC50 fishes 1 25 mg/l (96 h; Lepomis macrochirus)
LC50 other aquatic organisms 1 10-100 mg/l (96 h)
EC50 Daphnia 1 23 mg/l (48 h; Daphnia magna; LOCOMOTOR EFFECT)
LC50 fish 2 32 mg/l(96 h; Pimephales promelas)
EC50 Daphnia 2 27 mg/l (24 h; Daphnia magna)
TLM fish 1 25.1 mg/l (96 h; Lepomis macrochirus; SOFT WATER)
TLM fish 2 46.4 mg/l (96 h; Pimephales promelas; SOFT WATER)
TLM other aquatic organisms 1 10-100,96 h
Threshold limit other aquatic organisms 1 10-100,96 h; Pseudomonas putida
Threshold limit other aquatic organisms 272 mg/l
Threshold limit algae 1 > 200 mg/l (192 h; Scenedesmus quadricauda; INHIBITORY)
Threshold limit algae 2 67 mg/l (Microcystis aeruginosa; INHIBITORY)
12.2.Persistence and degradability
Composite Resource Clear Casting Resin(Mixture)
Persistence and degradability Not established.
styrene, inhibited (100-42-5)
Persistence and degradability Readily biodegradable in water. Not readily biodegradable in water. Forming sediments in
water. Non degradable in the soil. Adsorbs into the soil. Photodegradation in the air. Not
established.
Chemical oxygen demand (COD) 2.80 g O /g substance
ThOD 3.07 g O /g substance
BOD (% of ThOD) 0.42 % ThOD
Unsaturated Polyester Resin (TRADE SECRET)
Persistence and degradability Not established.
12.3.Bioaccumulative potential
Composite Resource Clear Casting Resin(Mixture)
Bioaccumulative potential Not established.
Composite Resource Clear Casting Resin
Safety Data SheetCR3040CC
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
12/17/2014 EN(English) SDS ID:CR3040CC 6/8
styrene, inhibited (100-42-5)
BCF fish 1 12-77 (QSAR)
BCF fish 2 35.5 (Carassius auratus)
Log Pow 2.95-3.16 (Experimental value)
Bioaccumulative potential Low potential for bioaccumulation (BCF < 500). Not established.
Unsaturated Polyester Resin (TRADE SECRET)
Bioaccumulative potential Not established.
12.4.Mobility in soil
styrene, inhibited (100-42-5)
Surface tension 0.032 N/m (19 C)
12.5.Other adverse effects
Other information :Avoid release to the environment.
SECTION 13:Disposal considerations
13.1.Waste treatment methods
Waste disposal recommendations :Dispose in a safe manner in accordance with local/national regulations. Dispose of
contents/container to ...
Additional information :Handle empty containers with care because residual vapours are flammable.
Ecology-waste materials :Avoid release to the environment.
SECTION 14:Transport information
In accordance with DOT
UN-No.(DOT) :UN1866
DOT Proper Shipping Name :RESIN SOLUTION
Department of Transportation (DOT) Hazard
Classes
:3-Class3-Flammable and combustible liquid 49 CFR 173.120
Hazard labels (DOT) :3-Flammable liquid
Packing group (DOT) :III-Minor Danger
Additional information
Other information :No supplementary information available.
ADR
Transport document description :UN UN1866 RESIN SOLUTION, III
Packing group (ADR) :III
Transport by sea
No additional information available
Air transport
No additional information available
SECTION 15:Regulatory information
15.1. US Federal regulations
Composite ResourceClear Casting Resin (Mixture)
RQ (Reportable quantity, section 304 of EPA's
List of Lists) :
1000 lb
styrene, inhibited (100-42-5)
RQ (Reportable quantity, section 304 of EPA's
List of Lists) :
1000 lb
Composite Resource Clear Casting Resin
Safety Data SheetCR3040CC
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
12/17/2014 EN(English) SDS ID:CR3040CC 7/8
styrene, inhibited (100-42-5)
SARA Section 311/312 Hazard Classes Immediate (acute) health hazard
Reactive hazard
Fire hazard
Delayed (chronic) health hazard
15.2. International regulations
CANADA
No additional information available
EU-Regulations
No additional information available
Classification according to Regulation (EC) No. 1272/2008 [CLP]
Not classified
Classification according to Directive 67/548/EEC or 1999/45/EC
Not classified
15.2.2.National regulations
styrene, inhibited (100-42-5)
Listed on EPA's Hazardous Air Pollutants (HAPS)
15.3. US State regulations
styrene, inhibited (100-42-5)
U.S.-California-
Proposition 65-
Carcinogens List
U.S.-California-
Proposition 65-
Developmental Toxicity
U.S.-California-
Proposition 65-
Reproductive Toxicity-
Female
U.S.-California-
Proposition 65-
Reproductive Toxicity-Male
No significance risk level
(NSRL)
styrene, inhibited (100-42-5)
U.S.-Massachusetts-Right To Know List
U.S.-New Jersey-Right to Know Hazardous Substance List
U.S.-Pennsylvania-RTK (Right to Know)-Environmental Hazard List
SECTION 16:Other information
Other information :None.
Full text of H-phrases: see section 16:
------Acute Tox. 4 (Inhalation:vapour) Acute toxicity (inhalation:vapour) Category 4
------Carc. 2 Carcinogenicity, Category 2
------Eye Irrit. 2A Serious eye damage/eye irritation, Category 2A
------Flam. Liq. 3 Flammable liquids, Category 3
------Skin Irrit. 2 Skin corrosion/irritation, Category 2
------H226 Flammable liquid and vapour
------H315 Causes skin irritation
------H319 Causes serious eye irritation
------H332 Harmful if inhaled
------H351 Suspected of causing cancer
SDS US (GHS HazCom 2012)
Composite Resource Clear Casting Resin
Safety Data SheetCR3040CC
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
12/17/2014 EN(English) SDS ID:CR3040CC 8/8
To the best of our knowledge this SDS is accurate. The the extent allowed by law, this statement is made inlieu of an other warranties, expressed or implied including but not limited to any implied
warranty of merchantability or fitness for a particular purpose and is in lieu of any other obligations or liability on the part of Dura Technoligies, Inc.
by | Sep 27, 2025
INDEX
CR3040CC
CR3040CCCG
CR3040CCCQ
CR3040CCG
CR3040CCQ
Composite Resource Clear Casting Resin
Safety Data SheetCR3040CC
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
Date of issue:12/17/2014 Revision date: Supersedes: Version:1.0
12/17/2014 EN(English) SDS ID:CR3040CC Page 1
SECTION 1:Identification of the substance/mixture and of the company/undertaking
1.1. Product identifier
Product form :Mixture
Trade name :Composite Resource Clear Casting Resin
CAS No :Mixture
Product code :CR3040CCCP,CR3040CCCQ,CR3040CCG , CR3040CCF
Other means of identification :DISTRIBUTED BY REVCHEM COMPOSITES, INC.
1.2. Relevant identified uses of the substance or mixture and uses advised against
Use of the substance/mixture :Clear Casting Resin
1.3. Details of the supplier of the safety data sheet
Composite Resources is supplied by Revchem Composites. 2720 South Willow Ave., Bloomington, CA 92316 1-800-281-4975
1.4. Emergency telephone number
Emergency number :800.424.9300
CHEMTREC: 1-800-424-9300
SECTION 2:Hazards identification
2.1. Classification of the substance or mixture
GHS-US classification
Flam. Liq. 3H226
Skin Irrit. 2H315
Eye Irrit. 2AH319
Carc. 2 H351
2.2. Label elements
GHS-US labelling
Hazard pictograms (GHS-US) :
GHS02 GHS07 GHS08
Signal word (GHS-US) :Warning
Hazard statements (GHS-US) :H226-Flammable liquid and vapour
H315-Causes skin irritation
H319-Causes serious eye irritation
H351-Suspected of causing cancer
Precautionary statements (GHS-US) :P201-Obtain special instructions before use
P202-Do not handle until all safety precautions have been read and understood
P210-Keep away from sparks.-No smoking
P233-Keep container tightly closed
P240-Ground/bond container and receiving equipment
P241-Use explosion-proof electrical equipment
P242-Use only non-sparking tools
P243-Take precautionary measures against static discharge
P264-Wash … thoroughly after handling
P280-Wear protective clothing
P302+P352-IF ON SKIN: Wash with plenty of soap and water
P303+P361+P353-IF ON SKIN (or hair): Remove/Take off immediately all contaminated
clothing. Rinse skin with water/shower
P305+P351+P338-If in eyes: Rinse cautiously with water for several minutes. Remove contact
lenses, if present and easy to do. Continue rinsing
P308+P313-IF exposed or concerned: Get medical advice/attention
P321-Specific treatment (see … on this label)
P332+P313-If skin irritation occurs: Get medical advice/attention
P337+P313-If eye irritation persists: Get medical advice/attention
P362-Take off contaminated clothing and wash before reuse
P370+P378-In case of fire: Use carbon dioxide (CO2), dry chemical powder, foam for
extinction
Composite Resource Clear Casting Resin
Safety Data SheetCR3040CC
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
12/17/2014 EN(English) SDS ID:CR3040CC 2/8
P403+P235-Store in a well-ventilated place. Keep cool
P405-Store locked up
P501-Dispose of contents/container to …
2.3. Other hazards
No additional information available
2.4. Unknown acute toxicity (GHS-US)
No data available
SECTION 3:Composition/information on ingredients
3.1. Substance
Not applicable
Full text of H-phrases: see section 16
3.2. Mixture
Name Product identifier % GHS-US classification
Unsaturated Polyester Resin (CAS No)TRADE SECRET 62-64 Not classified
Styrene, inhibited (CAS No)100-42-5 37 Flam. Liq. 3, H226
Acute Tox. 4 (Inhalation:vapour),
H332
Skin Irrit. 2, H315
Eye Irrit. 2A, H319
Carc. 2, H351
SECTION 4:First aid measures
4.1. Description of first aid measures
First-aid measures general :Never give anything by mouth to an unconscious person. If you feel unwell, seek medical advice
(show the label where possible). Suspected of causing cancer.
First-aid measures after inhalation :Assure fresh air breathing. Allow the victim to rest.
First-aid measures after skin contact :Rinse skin with water/shower. Remove/Take off immediately all contaminated clothing.Wash
with plenty of soap and water. Wash contaminated clothing before reuse. If skin irritation occurs:
Get medical advice/attention. Specific treatment (see … on this label).
First-aid measures after eye contact :Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to
do. Continue rinsing. If eye irritation persists: Get medical advice/attention.
First-aid measures after ingestion :Rinse mouth. Do NOT induce vomiting. Obtain emergency medical attention.
4.2. Most important symptoms and effects, both acute and delayed
Symptoms/injuries after skin contact :Causes skin irritation.
Symptoms/injuries after eye contact :Causes serious eye irritation.
4.3. Indication of any immediate medical attention and special treatment needed
No additional information available
SECTION 5:Firefighting measures
5.1. Extinguishing media
Suitable extinguishing media :Foam. Dry powder. Carbon dioxide. Water spray. Sand.
Unsuitable extinguishing media :Do not use a heavy waterstream.
5.2. Special hazards arising from the substance or mixture
Fire hazard :Extremely flammable liquid and vapour.
Explosion hazard :May form flammable/explosive vapour-air mixture.
5.3. Advice for firefighters
Firefighting instructions :Use water spray or fog for cooling exposed containers. Exercise caution when fighting any
chemical fire. Avoid (reject) fire-fighting water to enter environment.
Protection during firefighting :Do not enter fire area without proper protective equipment, including respiratory protection.
SECTION 6:Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
General measures :Remove ignition sources. Use special care to avoid static electric charges. No naked lights. No
smoking.
Composite Resource Clear Casting Resin
Safety Data SheetCR3040CC
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
12/17/2014 EN(English) SDS ID:CR3040CC 3/8
6.1.1.For non-emergency personnel
Emergency procedures :Evacuate unnecessary personnel.
6.1.2.For emergency responders
Protective equipment :Equip cleanup crew with proper protection.
Emergency procedures :Ventilate area.
6.2. Environmental precautions
Prevent entry to sewers and public waters. Notify authorities if liquid enters sewers or public waters.
6.3. Methods and material for containment and cleaning up
Methods for cleaning up :Soak up spills with inert solids, such as clay ordiatomaceous earth as soon as possible. Collect
spillage. Store away from other materials.
6.4. Reference to other sections
See Heading 8. Exposure controls and personal protection.
SECTION 7:Handling and storage
7.1. Precautions for safe handling
Additional hazards when processed :Handle empty containers with care because residual vapours are flammable.
Precautions for safe handling :Wash hands and other exposed areas with mild soap and water before eat, drink or smoke and
when leaving work. Provide good ventilation in process area to prevent formation of vapour. No
naked lights. No smoking. Take precautionary measures against static discharge. Use only non-
sparking tools. Obtain special instructions before use. Do not handle until all safety precautions
have been read and understood.
Hygiene measures :Wash … thoroughly after handling.
7.2. Conditions for safe storage, including any incompatibilities
Technical measures :Ground/bond container and receiving equipment. Use explosion-proof
electrical/ventilating/lighting/ equipment.
Storage conditions :Keep only in the original container in a cool, well ventilated place away from : Heat sources.
Keep in fireproof place. Keep container tightly closed.
Incompatible products :Strong bases. strongacids.
Incompatible materials :Sources of ignition. Direct sunlight. Heat sources.
7.3. Specific end use(s)
No additional information available
SECTION 8:Exposure controls/personal protection
8.1. Control parameters
styrene, inhibited (100-42-5)
USA ACGIH ACGIH TWA (ppm) 20 ppm
USA ACGIH ACGIH STEL (ppm) 40 ppm
8.2. Exposure controls
Personal protective equipment :Avoid all unnecessary exposure.
Hand protection :Wear protective gloves.
Eye protection :Chemical goggles or safety glasses.
Skin and body protection :Wear suitable protective clothing.
Respiratory protection :Wear approved mask.
Other information :When using, do not eat, drink or smoke.
SECTION 9:Physical and chemical properties
9.1. Information on basic physical and chemical properties
Physical state :Liquid
Appearance :Clear, colorless liquid
Colour :Clear
Odour :characteristic.
Odour threshold :No data available
pH :No data available
Relative evaporation rate (butylacetate=1):No data available
Composite Resource Clear Casting Resin
Safety Data SheetCR3040CC
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
12/17/2014 EN(English) SDS ID:CR3040CC 4/8
Relative evaporation rate (ether=1) :Slower than ether
Melting point :No data available
Freezing point :No data available
Boiling point :145.22 C Initial Boiling Point for Styrene @ 760.00 mm Hg(293.40 F)
Flash point :31.1 C for Volatile Component (88 F)
Auto-ignition temperature :No data available
Decomposition temperature :No data available
Flammability (solid, gas) :No data available
Vapour pressure :4.3 mm Hg Vapor pressure for Styrene at 20 C (68 F)
Relativevapour density at 20 C :3.6 (Air = 1)
Relative density :1-1.2 Relative Density @ 25 C (77 F)
Solubility :No data available
Log Pow :No data available
Log Kow :No data available
Viscosity, kinematic :No data available
Viscosity,dynamic :No data available
Explosive properties :No data available
Oxidising properties :No data available
Explosive limits :No data available
9.2. Other information
No additional information available
SECTION 10:Stability and reactivity
10.1.Reactivity
No additional information available
10.2.Chemical stability
Stable under normal conditions. Not established. Extremely flammable liquid and vapour. May form flammable/explosive vapour-air mixture.
10.3.Possibility of hazardous reactions
Not established.
10.4.Conditions to avoid
Direct sunlight. Extremely high or low temperatures. . Heat. Overheating. Open flame.
10.5.Incompatible materials
strong acids. Strong bases.
10.6.Hazardous decomposition products
fume. Carbon monoxide. Carbon dioxide. May release flammable gases.
SECTION 11:Toxicological information
11.1.Information on toxicological effects
Acute toxicity :Not classified
styrene, inhibited (100-42-5)
LD50 oral rat 5000 mg/kg (>6000 mg/kg bodyweight; Rat; Rat)
LD50 dermal rat 2820 mg/kg (>2000 mg/kg bodyweight; Rat; Rat; Experimental value)
LD50 dermal rabbit 5010 mg/kg (Rabbit)
LC50 inhalation rat (mg/l) 12 mg/l/4h (Rat)
LC50 inhalation rat (ppm) 2770 ppm/4h (Rat)
ATE CLP (oral) 5000.000 mg/kg bodyweight
ATE CLP (dermal) 2820.000 mg/kg bodyweight
ATE CLP (gases) 2770.000 ppmv/4h
ATE CLP (vapours) 12.000 mg/l/4h
ATE CLP (dust,mist) 12.000 mg/l/4h
Skin corrosion/irritation :Causes skin irritation.
Composite Resource Clear Casting Resin
Safety Data SheetCR3040CC
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
12/17/2014 EN(English) SDS ID:CR3040CC 5/8
Serious eye damage/irritation :Causes serious eye irritation.
Respiratory or skin sensitisation :Not classified
Germ cell mutagenicity :Not classified
Based on available data, the classification criteria are not met
Carcinogenicity :Suspected of causing cancer.
styrene, inhibited (100-42-5)
IARC group 2B-Possibly Carcinogenic to Humans
Reproductive toxicity :Not classified
Based on available data, the classification criteria are not met
Specific target organ toxicity (single exposure):Not classified
Specific target organ toxicity (repeated
exposure)
:Not classified
Based on available data, the classification criteria are not met
Aspiration hazard :Not classified
Based on available data, the classification criteria are not met
Potential Adverse human health effects and
symptoms
:Based on available data, the classification criteria are not met.
Symptoms/injuries after skin contact :Causes skin irritation.
Symptoms/injuries after eye contact :Causes serious eye irritation.
Likely routes of exposure :Inhalation
SECTION 12:Ecological information
12.1.Toxicity
styrene, inhibited (100-42-5)
LC50 fishes 1 25 mg/l (96 h; Lepomis macrochirus)
LC50 other aquatic organisms 1 10-100 mg/l (96 h)
EC50 Daphnia 1 23 mg/l (48 h; Daphnia magna; LOCOMOTOR EFFECT)
LC50 fish 2 32 mg/l(96 h; Pimephales promelas)
EC50 Daphnia 2 27 mg/l (24 h; Daphnia magna)
TLM fish 1 25.1 mg/l (96 h; Lepomis macrochirus; SOFT WATER)
TLM fish 2 46.4 mg/l (96 h; Pimephales promelas; SOFT WATER)
TLM other aquatic organisms 1 10-100,96 h
Threshold limit other aquatic organisms 1 10-100,96 h; Pseudomonas putida
Threshold limit other aquatic organisms 272 mg/l
Threshold limit algae 1 > 200 mg/l (192 h; Scenedesmus quadricauda; INHIBITORY)
Threshold limit algae 2 67 mg/l (Microcystis aeruginosa; INHIBITORY)
12.2.Persistence and degradability
Composite Resource Clear Casting Resin(Mixture)
Persistence and degradability Not established.
styrene, inhibited (100-42-5)
Persistence and degradability Readily biodegradable in water. Not readily biodegradable in water. Forming sediments in
water. Non degradable in the soil. Adsorbs into the soil. Photodegradation in the air. Not
established.
Chemical oxygen demand (COD) 2.80 g O /g substance
ThOD 3.07 g O /g substance
BOD (% of ThOD) 0.42 % ThOD
Unsaturated Polyester Resin (TRADE SECRET)
Persistence and degradability Not established.
12.3.Bioaccumulative potential
Composite Resource Clear Casting Resin(Mixture)
Bioaccumulative potential Not established.
Composite Resource Clear Casting Resin
Safety Data SheetCR3040CC
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
12/17/2014 EN(English) SDS ID:CR3040CC 6/8
styrene, inhibited (100-42-5)
BCF fish 1 12-77 (QSAR)
BCF fish 2 35.5 (Carassius auratus)
Log Pow 2.95-3.16 (Experimental value)
Bioaccumulative potential Low potential for bioaccumulation (BCF < 500). Not established.
Unsaturated Polyester Resin (TRADE SECRET)
Bioaccumulative potential Not established.
12.4.Mobility in soil
styrene, inhibited (100-42-5)
Surface tension 0.032 N/m (19 C)
12.5.Other adverse effects
Other information :Avoid release to the environment.
SECTION 13:Disposal considerations
13.1.Waste treatment methods
Waste disposal recommendations :Dispose in a safe manner in accordance with local/national regulations. Dispose of
contents/container to ...
Additional information :Handle empty containers with care because residual vapours are flammable.
Ecology-waste materials :Avoid release to the environment.
SECTION 14:Transport information
In accordance with DOT
UN-No.(DOT) :UN1866
DOT Proper Shipping Name :RESIN SOLUTION
Department of Transportation (DOT) Hazard
Classes
:3-Class3-Flammable and combustible liquid 49 CFR 173.120
Hazard labels (DOT) :3-Flammable liquid
Packing group (DOT) :III-Minor Danger
Additional information
Other information :No supplementary information available.
ADR
Transport document description :UN UN1866 RESIN SOLUTION, III
Packing group (ADR) :III
Transport by sea
No additional information available
Air transport
No additional information available
SECTION 15:Regulatory information
15.1. US Federal regulations
Composite ResourceClear Casting Resin (Mixture)
RQ (Reportable quantity, section 304 of EPA's
List of Lists) :
1000 lb
styrene, inhibited (100-42-5)
RQ (Reportable quantity, section 304 of EPA's
List of Lists) :
1000 lb
Composite Resource Clear Casting Resin
Safety Data SheetCR3040CC
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
12/17/2014 EN(English) SDS ID:CR3040CC 7/8
styrene, inhibited (100-42-5)
SARA Section 311/312 Hazard Classes Immediate (acute) health hazard
Reactive hazard
Fire hazard
Delayed (chronic) health hazard
15.2. International regulations
CANADA
No additional information available
EU-Regulations
No additional information available
Classification according to Regulation (EC) No. 1272/2008 [CLP]
Not classified
Classification according to Directive 67/548/EEC or 1999/45/EC
Not classified
15.2.2.National regulations
styrene, inhibited (100-42-5)
Listed on EPA's Hazardous Air Pollutants (HAPS)
15.3. US State regulations
styrene, inhibited (100-42-5)
U.S.-California-
Proposition 65-
Carcinogens List
U.S.-California-
Proposition 65-
Developmental Toxicity
U.S.-California-
Proposition 65-
Reproductive Toxicity-
Female
U.S.-California-
Proposition 65-
Reproductive Toxicity-Male
No significance risk level
(NSRL)
styrene, inhibited (100-42-5)
U.S.-Massachusetts-Right To Know List
U.S.-New Jersey-Right to Know Hazardous Substance List
U.S.-Pennsylvania-RTK (Right to Know)-Environmental Hazard List
SECTION 16:Other information
Other information :None.
Full text of H-phrases: see section 16:
------Acute Tox. 4 (Inhalation:vapour) Acute toxicity (inhalation:vapour) Category 4
------Carc. 2 Carcinogenicity, Category 2
------Eye Irrit. 2A Serious eye damage/eye irritation, Category 2A
------Flam. Liq. 3 Flammable liquids, Category 3
------Skin Irrit. 2 Skin corrosion/irritation, Category 2
------H226 Flammable liquid and vapour
------H315 Causes skin irritation
------H319 Causes serious eye irritation
------H332 Harmful if inhaled
------H351 Suspected of causing cancer
SDS US (GHS HazCom 2012)
Composite Resource Clear Casting Resin
Safety Data SheetCR3040CC
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
12/17/2014 EN(English) SDS ID:CR3040CC 8/8
To the best of our knowledge this SDS is accurate. The the extent allowed by law, this statement is made inlieu of an other warranties, expressed or implied including but not limited to any implied
warranty of merchantability or fitness for a particular purpose and is in lieu of any other obligations or liability on the part of Dura Technoligies, Inc.
