80605769_SDS.pdf

by | Sep 27, 2025

Safety Data Sheet
according to OSHA 1910.1200 Hazard Communication Standard
SikaBiresin AP007 (formerly APF 7) Part A

Revision Date 10/25/2023 Print Date 10/25/2023
1 / 13
SECTION 1. IDENTIFICATION
Product name : SikaBiresin AP007 (formerly APF 7) Part A
Company name : Sika Corporation
201 Polito Avenue
Lyndhurst, NJ 07071
USA
www.sikausa.com
Telephone :
(201) 933-8800
Telefax : (201) 804-1076
E-mail address : ehs@sika-corp.com
Emergency telephone : CHEMTREC: 800-424-9300
INTERNATIONAL: +1-703-527-3887
Recommended use of the chemical and restrictions on
use
: For further information, refer to product data sheet.
SECTION 2. HAZARDS IDENTIFICATION
GHS classification in accordance with the OSHA Hazard Communication Standard (29 CFR
1910.1200)
Flammable liquids : Category 3
Skin irritation : Category 2
Eye irritation : Category 2A
Carcinogenicity (Inhalation) : Category 1A
GHS label elements
Hazard pictograms :
Signal Word : Da nger
Hazard Statements : H226 Flammable liquid and vapor.
H315 Causes skin irritation.
H319 Causes serious eye irritation.
H350 May cause cancer by inhalation.

Safety Data Sheet
according to OSHA 1910.1200 Hazard Communication Standard
SikaBiresin AP007 (formerly APF 7) Part A

Revision Date 10/25/2023 Print Date 10/25/2023
2 / 13
Precautionary Statements :
Prevention:
P201 Obtain special instructions before use.
P202 Do not handle until all safety precautions have been read
and understood.
P210 Keep away from heat/ sparks/ open flames/ hot surfaces.
No smoking.
P233 Keep container tightly closed.
P240 Ground/bond container and receiving equipment.
P241 Use explosion-proof electrical/ ventilating/ lighting/ equip-
ment.
P242 Use only non-sparking tools.
P243 Take precautionary measures against static discharge.
P264 Wash skin thoroughly after handling.
P280 Wear protective gloves/ protective clothing/ eye protection/
face protection.
Response:
P303 + P361 + P353 IF ON SKIN (or hair): Take off immediately
all contaminated clothing. Rinse skin with water/ shower.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water
for several minutes. Remove contact lenses, if present and easy
to do. Continue rinsing.
P308 + P313 IF exposed or concerned: Get medical advice/
attention.
P332 + P313 If skin irritation occurs: Get medical advice/ atten-
tion.
P337 + P313 If eye irritation persists: Get medical advice/ atten-
tion.
P362 + P364 Take off contaminated clothing and wash it before
reuse.
P370 + P378 In case of fire: Use dry sand, dry chemical or alco-
hol-resistant foam to extinguish.
Storage:
P403 + P235 Store in a well-ventilated place. Keep cool.
P405 Store locked up.
Disposal:
P501 Dispose of contents/ container to an approved waste dis-
posal plant.
Additional Labeling
There are no ingredients with unknown acute toxicity used in a mixture at a concentration >= 1%.
Other hazards
None known.

Safety Data Sheet
according to OSHA 1910.1200 Hazard Communication Standard
SikaBiresin AP007 (formerly APF 7) Part A

Revision Date 10/25/2023 Print Date 10/25/2023
3 / 13
SECTI ON 3. COMPOSITION/INFORMATION ON INGREDIENTS
Mixtures
Components
Chemical name CAS-No. Classification Concentra-
tion (% w/w)
Talc 14807-96-6 >= 50 – < 70 vinyltoluene 25013-15-4 Flam. Liq. 3; H226 Acute Tox. 4; H332 Skin Irrit. 2; H315 Eye Irrit. 2A; H319 Asp. Tox. 1; H304 >= 10 – < 20 barium sulfate 7727-43-7 >= 1 – < 5 Quartz (SiO2) >5 m 14808-60-7 Carc. 1A; H350
STOT RE 1; H372
STOT SE 3; H335
>= 0.1 – < 1 Actual concentration is withheld as a trade secret SECTION 4. FIRST AID MEASURES General advice : Move out of dangerous area. Consult a physician. Show this material safety data sheet to the doctor in attend- ance. If inhaled : Move to fresh air. Consult a physician after significant exposure. In case of skin contact : Take off contaminated clothing and shoes immediately. Wash off with soap and plenty of water. If symptoms persist, call a physician. In case of eye contact : Immediately flush eye(s) with plenty of water. Remove contact lenses. Keep eye wide open while rinsing. If eye irritation persists, consult a specialist. If swallowed : Clean mouth with water and drink afterwards plenty of water. Do not induce vomiting without medical advice. Do not give milk or alcoholic beverages. Never give anything by mouth to an unconscious person. Obtain medical attention. Most important symptoms and effects, both acute and delayed : irritant effects Excessive lachrymation Erythema Dermatitis Causes skin irritation. Causes serious e ye irritation. Safety Data Sheet according to OSHA 1910.1200 Hazard Communication Standard SikaBiresin AP007 (formerly APF 7) Part A Revision Date 10/25/2023 Print Date 10/25/2023 4 / 13 May caus e cancer by inhalation. Notes to physician : Treat symptomatically. SECTION 5. FIRE-FIGHTING MEASURES Suitable extinguishing media : Alcohol-resistant foam Carbon dioxide (CO2) Dry chemical Unsuitable extinguishing media : Water Further information : Use water spray to cool unopened containers. Collect contaminated fire extinguishing water separately. This must not be discharged into drains. Fire residues and contaminated fire extinguishing water must be disposed of in accordance with local regulations. Special protective equipment for fire-fighters : In the event of fire, wear self-contained breathing apparatus. SECTION 6. ACCIDENTAL RELEASE MEASURES Personal precautions, protec- tive equipment and emer- gency procedures : Use personal protective equipment. Remove all sources of ignition. Deny access to unprotected persons. Beware of vapors accumulating to form explosive concentra- tions. Vapors can accumulate in low areas. Environmental precautions : Prevent product from entering drains. If the product contaminates rivers and lakes or drains inform respective authorities. Local authorities should be advised if significant spillages cannot be contained. Methods and materials for containment and cleaning up : Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust). SECTION 7. HANDLING AND STORAGE Advice on protection against fire and explosion : Use explosion-proof equipment. Keep away from heat/ sparks/ open flames/ hot surfaces. No smoking. Take precautionary measures against electrostatic discharg- es. Advice on safe handling : Do not breathe vapors or spray mist. Avoid exceeding the given occupational exposure limits (see section 8 ). Safety Data Sheet according to OSHA 1910.1200 Hazard Communication Standard SikaBiresin AP007 (formerly APF 7) Part A Revision Date 10/25/2023 Print Date 10/25/2023 5 / 13 Do not get in eye s, on skin, or on clothing. For personal protection see section 8. Smoking, eating and drinking should be prohibited in the ap- plication area. Take precautionary measures against static discharge. Open drum carefully as content may be under pressure. Take necessary action to avoid static electricity discharge (which might cause ignition of organic vapors). Follow standard hygiene measures when handling chemical products. Conditions for safe storage : Store in original container. Keep in a well-ventilated place. Observe label precautions. Store in accordance with local regulations. Materials to avoid : Explosives Oxidizing agents Poisonous gases Poisonous liquids SECTION 8. EXPOSURE CONTRO LS/PERSONAL PROTECTION Ingredients with workplace control parameters Components CAS-No. Value type (Form of exposure) Control parame- ters / Permissible concentration Basis Talc 14807-96-6 TWA (Dust) 20 Million parti- cles per cubic foot OSHA Z-3 TWA (respir- able dust frac tion ) 2 mg/m3 OSHA P0 TWA (Res - pirable par- ticulate mat- ter ) 2 mg/m3 ACGIH PEL (resp ir- able) 0.05 mg/m3 OSHA CARC vinyltoluene 25013-15-4 TW A 50 ppm ACGIH STEL 100 ppm ACGIH TWA 100 pp m 480 mg/m3 OSHA Z-1 TWA 100 pp m 480 mg/m3 OSHA P0 barium sulfate 7727-43-7 TWA (Inhal- able particu- late matter ) 5 mg/m3 ACGIH TWA (total dus t) 15 mg/m3 OSHA Z-1 Safety Data Sheet according to OSHA 1910.1200 Hazard Communication Standard SikaBiresin AP007 (formerly APF 7) Part A Revision Date 10/25/2023 Print Date 10/25/2023 6 / 13 TWA (respir- able fraction) 5 mg/m3 OSHA Z-1 TWA (Total dus t) 10 mg/m3 OSHA P0 TWA (respir- able dust fraction ) 5 mg/m3 OSHA P0 Quartz (SiO2) >5 m 14808-60-7 TWA (Res-
pirable par-
ticulate mat-
ter)
0.025 mg/m3 ACGIH
TWA (Res-
pira
ble dust
)
0.05 mg/m3 OSHA Z-1
TWA (respir- able
)
10 mg/m3 / %SiO2+2
OSHA Z-3
TWA (respir-
able)
250 mppcf / %SiO2+5
OSHA Z-3
TWA (respir- able dust
fraction
)
0.1 mg/m3 OSHA P0
TWA (Res-
pira
ble par-
ticulate mat- ter )
0.025 mg/m3 (Silica)
ACGIH
PEL (respir-
able)
0.05 mg/m3 OSHA CARC
TWA (respir- able dust
fraction
)
0.1 mg/m3 OSHA P0
TWA (Res-
pira
ble par-
ticulate mat-
ter
)
0.025 mg/m3 ACGIH
TWA (Res-
pira
ble par-
ticulate mat- ter )
0.025 mg/m3
(Silica)
ACGIH
The above constituent s are the only constituents of the product which have a PEL, TLV or other rec-
ommended exposure limit. At this time, the other constituents have no known exposure limits.
Engineering measures : Use of adequate ventilation should be sufficient to control
worker exposure to airborne contaminants. If the use of this
product generates dust, fumes, gas, vapor or mist, use pro-
cess enclosures, local exhaust ventilation or other engineer-
ing controls to keep worker exposure below any recommend-
ed or statutory limits.
The engineering controls also need to keep gas, vapor or
dust concentrations below an
y lower explosive limits.

Safety Data Sheet
according to OSHA 1910.1200 Hazard Communication Standard
SikaBiresin AP007 (formerly APF 7) Part A

Revision Date 10/25/2023 Print Date 10/25/2023
7 / 13
Personal protec tive equipment
Respiratory protection : Use a properly fitted NIOSH approved air-purifying or air-fed
respirator complying with an approved standard if a risk as-
sessment indicates this is necessary.
The filter class for the respirator must be suitable for the max-
imum expected contaminant concentration
(gas/vapor/aerosol/particulates) that may arise when han-
dling the product. If this concentration is exceeded, self-
contained breathing apparatus must be used.
Hand protection : Chemical-resistant, impervious gloves complying with an
approved standard should be worn at all times when handling
chemical products if a risk assessment indicates this is nec-
essary.
Eye protection : Safety eyewear complying with an approved standard should
be used when a risk assessment indicates this is necessary.
Skin and body protection : Choose body protection in relation to its type, to the concen-
tration and amount of dangerous substances, and to the spe-
cific work-place.
Hygiene measures : Avoid contact with skin, eyes and clothing.
Wash hands before breaks and immediately after handling
the product.
Remove respiratory and skin/eye protection only after vapors
have been cleared from the area.
Remove contaminated clothing and protective equipment
before entering eating areas.
Wash thoroughly after handling.
SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance : paste
Color : various
Odor : pungent
Odor Threshold : No data available
pH : Not applicable
Melting point/range / Freezing
poin
t
: No data available
Boiling point/boiling range : 338 F / 170 C
Flash point : 127 F / 53 C
(Method: closed cup)

Safety Data Sheet
according to OSHA 1910.1200 Hazard Communication Standard
SikaBiresin AP007 (formerly APF 7) Part A

Revision Date 10/25/2023 Print Date 10/25/2023
8 / 13
Evaporation rate : No data available
Flammability (solid, gas) : No data available
Upper explosion limit / Upper
flammability limit
: No data available
Lower explosion limit / Lower
flammability limit
: No data available
Vapor pressure : 2 hpa
Relative vapor density : No data available
Density : 1.59 – 2.13 g/cm3 (68 F / 20 C)
Solubility(ies)
Water solubility : soluble
Solubility in other solvents : No data available
Partition coefficient: n-
octanol/water
: No data available
Autoignition temperature : No data available
Decomposition temperature : No data available
Viscosity
Viscosity, dynamic : No data available
Viscosity, kinematic : > 20.55 mm2/s (104 F / 40 C)
Explosive properties : No data available
Oxidizing properties : No data available
Volatile organic compounds
(VOC) content
: 352 g/l
Part A + Valspar Cream Hardener BPO Part B
SECTION 10. STABILITY AND REACTIVITY
Reactivity : No dangerous reaction known under conditions of normal use.
Chemical stability : The product is chemically stable.
Possibility of hazardous reac-
tions
: Stable under recommended storage conditions.
Vapors may form explosive mixture with air.
Conditions to avoid : Heat, flames and sparks.
Incompatible materials : No data available

Safety Data Sheet
according to OSHA 1910.1200 Hazard Communication Standard
SikaBiresin AP007 (formerly APF 7) Part A

Revision Date 10/25/2023 Print Date 10/25/2023
9 / 13
Hazardous decomposition
products
: No decomposition if stored and applied as directed.
SECTION 11. TOXICOLOGICAL INFORMATION
Not classified due to lack of data.
Skin corrosion/irritation
Causes skin irritation.
Serious eye damage/eye irritation
Causes serious eye irritation.
Respiratory or skin sensitization
Skin sensitization
Not classified due to lack of data.
Respiratory sensitization
Not classified due to lack of data.
Germ cell mutagenicity
Not classified due to lack of data.
Carcinogenicity
May cause cancer by inhalation.
IARC Group 1: Carcinogenic to humans
Quartz (SiO2) 14808-60-7
(Silica dust, crystalline)
Group 2B: Possibly carcinogenic to humans
Titanium dioxide (> 10 m) 13463-67-7
OSHA OSHA specifically regulated carcinogen
Talc (Mg3H2(SiO3)4) 14807-96-6
(crystalline silica)
OSHA specifically regulated carcinogen
Quartz (SiO2) 14808-60-7
(crystalline silica)
NTP Known to be human carcinogen
Quartz (SiO2) 14808-60-7
(Silica, Crystalline (Respirable Size))
Reproductive toxicity
Not classified due to lack of data.
STOT-single exposure
Not classified due to lack of data.

Safety Data Sheet
according to OSHA 1910.1200 Hazard Communication Standard
SikaBiresin AP007 (formerly APF 7) Part A

Revision Date 10/25/2023 Print Date 10/25/2023
10 / 13
STOT-repea ted exposure
Not classified due to lack of data.
Aspiration toxicity
Not classified due to lack of data.
Further information
Product:
Remarks : Titanium dioxide (13463-67-7)
In lifetime inhalation studies of rats, airborne respirable-size
titanium dioxide particles have shown to cause an increase in
lung tumors at concentrations associated with substantial
particle lung burdens and consequential pulmonary overload
and inflammation. The potential for these adverse health ef-
fects appears to be closely related to the particle size and the
amount of the exposed surface area that comes into contact
with the lung. However, tests with other laboratory animals
such as mice and hamsters, indicate that rats are significantly
more susceptible to the pulmonary overload and inflammation
that causes lung cancer. Epidemiological studies do not sug-
gest an increased risk of cancer in humans from occupational
exposure to titanium dioxide. Titanium dioxide has been char-
acterized by IARC as possibly carcinogenic to humans (Group
2B) through inhalation (not ingestion). It has not been charac-
terized as a potential carcino
gen by either NTP or OSHA.
Quartz (14808-60-7): This classification is relevant when ex- posed to Quartz (silicon dioxide) in dust or powder form only,
including cured product that is subject to sanding, grinding,
cutting, or other surface preparation activities.
SECTION 12. ECOLOGICAL INFORMATION
Ecotoxicity
No data available
Persistence and degradability
No data available
Bioaccumulative potential
No data available
Mobility in soil
No data available
Other adverse effects
Product:
Additional ecological infor-
mation
: Do not empty into drains; dispose of this material and its con-
tainer in a safe way.
Avoid dispersal of spilled material and runoff and contact with

Safety Data Sheet
according to OSHA 1910.1200 Hazard Communication Standard
SikaBiresin AP007 (formerly APF 7) Part A

Revision Date 10/25/2023 Print Date 10/25/2023
11 / 13
soil, wate rways, drains and sewers.
SECTION 13. DISPOSAL CONSIDERATIONS
Disposal methods
Waste from residues : Disposal of this product, solutions and any by-products should
at all times comply with the requirements of environmental
protection and waste disposal legislation and any regional
local authority requirements.
Contaminated packaging : Empty containers should be taken to an approved waste han-
dling site for recycling or disposal.
SECTION 14. TRANSPORT INFORMATION
International Regulations
IATA-DGR
UN/ID No. : UN 1866
Proper shipping name : Resin solution
Class : 3
Packing group : III
Labels : Flammable Liquids
Packing instruction (cargo
aircraft)
: 366
Packing instruction (passen-
ger aircraft)
: 355
IMDG-Code
UN number : UN 1866
Proper shipping name : RESIN SOLUTION
Class : 3
Packing group : III
Labels : 3
EmS Code : F-E, S-E
Marine pollutant : no
Domestic regulation
49 CFR
UN/ID/NA number : UN 1866
Proper shipping name : Resin solution
Class : 3
Packing group : III
Labels : FLAMMABLE LIQUID
ERG Code : 127
Marine pollutant : no
DOT: As per 49CFR 173.150 (f) Combustible Liquid Exception, Material is Not Regulated.
DOT: For Limited Quantity exceptions reference 49 CFR 173.150 (b)

Safety Data Sheet
according to OSHA 1910.1200 Hazard Communication Standard
SikaBiresin AP007 (formerly APF 7) Part A

Revision Date 10/25/2023 Print Date 10/25/2023
12 / 13
IMDG: For Limited Quan tity special provisions reference IMDG Code Chapter 3.4
Special precautions for user
The transport classification(s) provided herein are for informational purposes only, and solely based
upon the properties of the unpackaged material as it is described within this Safety Data Sheet.
Transportation classifications may vary by mode of transportation, package sizes, and variations in
regional or country regulations.
SECTION 15. REGULATORY INFORMATION
TSCA list : All chemical substances in this product are either listed as ac-
tive on the TSCA Inventory or are in compliance with a TSCA
Inventory exemption.
No substances are subject to a Significant New Use Rule.
The following substance(s) is/are subject to TSCA 12(b) export notification requirements:
vinyltoluene 25013-15-4
CERCLA Reportable Quantity
Listed substances in the product are at low enough levels to not be expected to exceed the RQ
SARA 304 Extremely Hazardous Substances Reportable Quantity
Listed substances in the product are at low enough levels to not be expected to exceed the RQ
SARA 302 Extremely Hazardous Substances Threshold Planning Quantity
This material does not contain any components with a section 302 EHS TPQ.
SARA 311/312 Hazards : Flammable (gases, aerosols, liquids, or solids)
Carcinogenicity
Skin corrosion or irritation
Serious eye damage or eye irritation
SARA 313 : This material does not contain any chemical components with
known CAS numbers that exceed the threshold (De Minimis)
reporting levels established by SARA Title III, Section 313.
Clean Air Act
This product does not contain any hazardous air pollutants (HAP), as defined by the U.S. Clean Air
Act Section 112 (40 CFR 61).
California Prop. 65
WARNING: This product can expose you to chemicals including Talc, which is known to the State of
California to cause cancer, and methanol, which is known to the State of California to cause birth
defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
SECTION 16. OTHER INFORMATION
Full text of other abbreviations

Safety Data Sheet
according to OSHA 1910.1200 Hazard Communication Standard
SikaBiresin AP007 (formerly APF 7) Part A

Revision Date 10/25/2023 Print Date 10/25/2023
13 / 13
ACGIH : USA. ACGIH Threshold Limit Values (TLV)
OSHA CARC : OSHA Specifically Regulated Chemicals/Carcinogens
OSHA P0 : USA. Table Z-1-A Limits for Air Contaminants (1989 vacated
values)
OSHA Z-1 : USA. Occupational Exposure Limits (OSHA) – Table Z-1 Lim-
its for Air Contaminants
OSHA Z-3 : USA. Occupational Exposure Limits (OSHA) – Table Z-3 Min-
eral Dusts
ACGIH / TWA : 8-hour, time-weighted average
ACGIH / STEL : Short-term exposure limit
OSHA CARC / PEL : Permissible exposure limit (PEL)
OSHA P0 / TWA : 8-hour time weighted average
OSHA Z-1 / TWA : 8-hour time weighted average
OSHA Z-3 / TWA : 8-hour time weighted average
Notes to Reader
The information contained in this Safety Data Sheet applies only to the actual Sika Corporation
(“Sika”) product identified and described herein. This information is not intended to address, nor
does it address the use or application of the identified Sika product in combination with any other
material, product or process. All of the information set forth herein is based on technical data re-
garding the identified product that Sika believes to be reliable as of the date hereof. Prior to each
use of any Sika product, the user must always read and follow the warnings and instructions on
the product’s current Product Data Sheet, product label and Safety Data Sheet for each Sika
product, which are available at web site and/or telephone number listed in Section 1 of this SDS.
SIKA MAKES NO WARRANTIES EXPRESS OR IMPLIED AND ASSUMES NO LIABILITY
ARISING FROM THIS INFORMATION OR ITS USE. SIKA SHALL NOT BE LIABLE UNDER
ANY LEGAL THEORY FOR SPECIAL OR CONS EQUENTIAL DAMAGES AND SHALL NOT BE
RESPONSIBLE FOR THE USE OF THIS PRO DUCT IN A MANNER TO INFRINGE ON ANY
PATENT OR ANY OTHER INTELLECTUAL PROPERTY RIGHTS HELD BY OTHERS.
All sales of Sika products are subject to its current terms and conditions of sale available at
www.sikausa.com or 201-933-8800.
Revision Date 10/25/2023
100000035109
US / Z8

80502002F_SDS.pdf

by | Sep 27, 2025

Page 1 of 7

SAFETY DATA SHEET
EPOXY AF JET BLACK

1. PRODUCT AND COMPANY IDENTIFICATION

MANUFACTURER
CONSOLIDATED COLOR CORPORATION
12316 E CARSON STREET
HAWAIIAN GARDENS, CA, 90716
562-420-7714

24 HR. EMERGENCY TELEPHONE NUMBER
CHEMTREC (US Transportation): (800)424 -9300
CHEMTREC (Int l. Transportation): 1(202)483-7616

2. HAZARDS IDENTIFICATION

EMERGENCY OVERVIEW

PHYSICAL APPEARANCE: Fluid, colored paste with slight odor.

GHS CLASSIFICATION:
Eye Irritation, 2B
Skin Irritation, 2
Skin Sensitization, 1B
Aquatic Toxicity, 4
Carcinogenicity, 2

SIGNAL WORD : Warning

HAZARD STATEMENT(S):
H315: Causes skin irritation
H317: May cause an allergic skin reaction
H319: Causes serious eye irritation
H411: Toxic to aquatic life with long lasting effects
H351: Suspected of causing cancer.
DATE ISSUED : 5/16/2019
MSDS REF. No : CED 7122
PRODUCT NAME: EPOXY AF JET BLACK

PRODUCT CODE: CED 7122

Page 2 of 7

PRECAUTIONARY STATEMENT(S ):
P261: Avoid breathing dust/fume/gas/mist/vapor/spray.
P264: Wash hands thoroughly after handling.
P272: Contaminated work clothing should not be allowed out of workplace.
P273: Avoid release into the environment.
P280: Wear protective gloves/ protective clothing/ eye protection/ face protection.
P302+P352: IF ON SKIN: Was with plenty of soap and water.
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact
lenses, if present and easy to do. Continue rinsing.
P332+P333+P313: If skin irritation occurs: If eye irritation persists: Get medical attention/advice.
P362: Take off contaminated clothing and wash before reuse.
P391: Collect spillage.
P501: Dispose of contents and container in accordance with all local, regional, national, and
international regulations.

OTHER HAZARDS:
Hazards not otherwise classified (HNOC).

3. COMPOSITION/INFORMATION ON INGREDIENTS

Chemical Name Weight % CAS Number
Bisphenol A Epoxy Resin 60% to 70% 25068-38-6
Glycidyl Neodecanoate 10% to 20% 26761-45-5
Carbon Black 10% to 20% 1333-86-4

There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations
applicable, are classified as hazardous to health or the environment and thus require reporting in this section.
Occupational exposure limits, if available, are listed in Section 8.

The exact % composition has been withheld as a trade secret.

4. FIRST AID MEASURES

EYES: Flush with water for 15 minutes. See a physician if irritation persists.

SKIN: Rinse skin with soap and water. See a physician if irritation persists.

INGESTION: Do not induce vomiting without medical advice. Keep respiratory tract clean. Never
give anything by mouth to an unconscious person. Get medical assistance (call 911) immediately.

INHALATION: Remove the victim to fresh air. If breathing is difficult, administer oxygen. If
breathing has stopped give artificial respiration. Keep person warm and seek medical attention
immediately.

NOTES TO PHYSICIAN: Consult a physician if necessary.

5. FIRE FIGHTING MEASURES

AUTOIGNITION TEMPERATURE: No data

FLAMMABLE CLASS: Not flammable.

Page 3 of 7

EXTINGUISHING MEDIA: Alcohol-resistant foam, carbon dioxide, dry chemical

FIRE FIGHTING PROCEDURES: For fire-fighters, use self-contained breathing apparatus.
Water spray may be used to cool fully closed containers. Do not allow run-off from fire-fighting to
enter drains or water courses.

FIRE FIGHTING EQUIPMENT: As in any fire, wear self-contained breathing apparatus pressure-
demand (MSHA/NIOSH) approved or equivalent) and full protective gear.

6. ACCIDENTAL RELEASE MEASURES

METHODS AND MATERIALS FOR CONTAINMENT AND CLEAN UP

SMALL SPILL: Dike and contain spillage. Scoop us material and place into suitable
container(s) for disposal according to local and federal regulations.

LARGE SPILL: Prevent product from entering storm drains. If the product contaminates
rivers and lakes or drains inform respective authorities.

ENVIRONMENTAL PRECAUTIONS

WATER SPILL: OBEY ALL LOCAL, STATE AND FEDERAL REGULATIONS.

LAND SPILL: OBEY ALL LOCAL, STATE AND FEDERAL REGULATIONS.

7. HANDLING AND STORAGE

PRECAUTIONS FOR SAFE HANDLING

Do not breathe vapors/dust.
Keep containers closed when not in use.
For industrial use only.
Keep out of reach from children.
No smoking in the work area.

CONDITIONS FOR STORAGE INCLUDING ANY INCOMPATIBILITIES

Keep containers tightly closed in a dry well-ventilated place. Containers which are opened must
be carefully resealed and kept upright to prevent leakage. Store away from incompatible
materials.

8. EXPOSURE CONTROLS/ PERSONAL PROTECTION

EXPOSURE LIMITS

Components CAS No. Limits
Carbon Black 1333-86-4 3.5 mg/m3 OSHA -PEL; 3.0 mg/m3
ACGIH-TLV

ENGINEERING CONTROLS: Provide adequate ventilation. Use an appropriate exhaust system in
the work area.

Page 4 of 7

PERSONAL PROTECTIVE EQUIPMENT

EYES AND FACE: Wear tight-fitting safety goggles. Do not wear contact lenses.
SKIN: Use impermeable rubber gloves. Remove contaminated clothing.
RESPIRATORY: Use NIOSH approved respirators when permissible exposure limits are
exceeded.

WORK HYGIENIC PRACTICES:
Keep containers closed when not in use. Wash hands before breaks and at the end of work day.

OTHER PROTECTIVE EQUIPMENT :
Ensure that working areas contain safety showers and eye wash stations. Handle material in
accordance with good safety and hygiene practices.

9. PHYSICAL AND CHEMICAL PROPERTIES

PHYSICAL STATE: Liquid
COLOR: colored paste
ODOR: Low odor
ODOR THRESHOLD: No data available
pH: Not applicable
MELTING POINT ( F): Not available.
BOILING POINT ( F): 498.0 – 532.0
FLASH POINT ( F): 259.00, PMCC
LOWER EXPLOSION LIMIT (%): Not applicable
UPPER EXPLOSION LIMIT (%): Not applicable
VAPOR DENSITY: Heavier than air.
VAPOR PRESSURE , ESTIMATED(68 F): Not available
DENSITY (lbs/gal.): 10.0952
SOLIDS IN WT.%: 98.9250
EVAPORATION RATE: Greater than butyl acetate (Butyl acetate = 1)
SOLUBILITY IN WATER: Negligible
MATERIAL VOC (grams/liter): 3.00
COATING VOC (grams/liter): 3.00

10. STABILITY AND REACTIVITY

STABILITY: MATERIAL IS STABLE.

HAZARDOUS POLYMERIZATION: Product will not undergo polymerization.
Hazardous reactions or instability may occur under certain conditions of storage or use.

CONDITIONS TO AVOID: High temperatures, open flames or sparks.

HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition may yield carbon dioxide
and/or carbon monoxide.

INCOMPATIBLE MATERIALS: Avoid mixing with strong oxidizers or reducing agents.

Page 5 of 7

11. TOXICOLOGICAL INFORMATION

TOXICOLOGICAL EFFECTS

ACUTE TOXICITY:
LD50/oral/rat: >10,000 mg/kg
LD50/dermal/rat: >20,000 mg/kg
LC50/inhalation: no data available

POTENTIAL HEALTH EFFECTS:
EYES: Causes eye irritation.
SKIN: May cause skin irritation and possible allergic reaction.
SKIN ABSORPTION: No hazard during normal industrial use.
INGESTION: No hazard during normal industrial use. For industrial use only.
INHALATION: Maybe harmful if inhaled. Avoid breathing vapors of liquid.

CARCINOGENICITY: IARC (International Agency for Research on Cancer) has classified carbon
black as Group 2B; possibly carcinogenic to humans. Assessment on toxicity for carbon black;
non-toxic after a single ingestion and/or skin contact, no deaths at the highest dose tested after
short-term inhalation.

NTP: No
IARC: Yes
OSHA: No

MUTAGENICITY: No evidence of adverse effects.

12. ECOLOGICAL INFORMATION

ECOTOXICITY EFFECTS :

Harmful to aquatic life. This product is known as a water pollutant. It may be harmful to the
environment if released in large quantities. Inform the relevant authorities if the product has
caused environmental pollution. Collect spillage.

PERSISTENCE AND DEGRADABILITY:

Biodegradability: No data available
Mobility in soil : No data available
Bioaccumulation: No data available

13. DISPOSAL CONSIDERATIONS

DISPOSAL METHOD: Dispose of in accordance to all local, state and federal regulations.

EMPTY CONTAINER: Empty remaining contents. Dispose of as unused product as hazardous
waste. Do not re-use empty containers. Do not burn nor use cutting tools on the empty
containers.

RCRA/EPA WASTE INFORMATION: Obey all local, state and federal regulations.

Page 6 of 7

14. TRANSPORT INFORMATION

DOT (DEPARTMENT OF TRANSPORTATION)
SHIPPING NAME : Not regulated
SHIPPING DECSRIPTION : Not regulated

IMDG: Not regulated

IATA: Not regulated

15. REGULATORY INFORMATION

UNITED STATES

SARA TITLE III (SUPERFUND AMENDMENT S AND REAUTHORIZATION ACT)

Section 302/304 : No chemicals subject to the reporting requirements of SARA Title III,
Section 302.

Section 311/312 : Acute health hazard.

Section 313 : The product does not contain any chemical components with known
CAS numbers that exceed the threshold (de minimis) reporting levels established by SARA
Title III, Section 313.

CA PROPOSITION 65 :
WARNING: This product can expose you to chemicals includi ng [Carbon Black] which is known to
the State of California to cause cancer.

For more information go to http://www.p65warnings.ca.gov.

STATE RTK:
MA, NJ, PA
Carbon Black CAS# 1333-86-4

TSCA INVENTORY: All components are listed or exempted.

The components of this product are reported in the following inventories:

REACH (EU): All components are listed or exempted.
Australia (AICS): At least one component is not listed.
Canada (DSL): All components are listed or exempted.
China (IECSC): All components are listed or exempted.
Japan (ENCS/ISHL): All components are listed or exempted.
Korea (ECL/KECI): All components are listed or exempted.
New Zealand (NZIoC): All components are listed or exempted.
Philippines (PICCS): All components are listed or exempted.
Taiwan (TCSI/CSNN): At least one component is not listed.

16. OTHER INFORMATION

HMIS RATING
Health : 2
Flammability : 1
Reactivity : 0
Personal Protection : B

DISCLAIMER : THE INFORMATION OR RECOMMENDATIONS CONTAINED HEREIN ARE BASED ON
INFORMATION OBTAINED FROM SOURCES WHICH WE BELIEVE ARE RELIABLE AND ARE
PROPRIETARY AND ARE FURNISHED SOLELY FOR THE USE OF OUR CUSTOMERS. SINCE IT IS
IMPOSSIBLE FOR US TO DETERMINE THE PRECISE CONDITIONS UNDER WHICH OUR PRODUCTS
WILL BE USED, NEITHER CONS OLIDATED COLOR CORPORATION NOR ITS AFFILIATES CAN ACCEPT
RESPONSIBILITY FOR LOSS, INJURY OR OTHER DAMAGES RESULTING FROM THE USE OF THE
PRODUCT OR THIS OR ANY OTHER INFORMATION PROVIDED BY US. USERS ARE ADVISED TO
MAKE THEIR OWN TESTS TO DETERMINE THE SAFE TY, SUITABILITY, AND RELEVANCE OF FEDERAL
AND LOCAL LAW TO THE PRODUCT AS IT IS TO BE USED BY THEM. THEREFORE NO GUARANTEE
OF ANY KIND EXPRESSED OR IMPLIED, INCLUDING THOSE OF FITNESS OR MERCHANTABILITY,
ARE MADE BY CONSOLIDATED COLOR CORPORATION OR ITS AF FILIATES WITH REGARD TO ANY
OF THEIR PRODUCTS.

NFPA CODES
1
0
2

804-038-UN-1866mixture_SDS.pdf

by | Sep 27, 2025

NPG Fast Putty
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
03/24/2021EN (English)Page 1
SECTION 1: Identification
1.1. Identification
Product form :MixtureTrade name :NPG Fast PuttyCAS-No. :mixtureProduct code :804-038Formula :na
1.2. Recommended use and restrictions on use
Use of the substance/mixture :BONDING PUTTY
1.3. Supplier
Dura Technologies, Inc.
2720 South Willow Avenue #A
Bloomington, CA 92316
909-546-1162
ChemTrec US: 800.424.9300
ChemTrec Int: +1 70 3527 3887
1.4. Emergency telephone number
Emergency number :ChemTrec US: 800.424.9300 Int: +1 70 3527 3887
CHEMTREC: 1-800-424-9300
SECTION 2: Hazard(s) identification
2.1. Classification of the substance or mixture
GHS-US classification
Flammable liquids,
Category 3
H226 Flammable liquid and vapour.Skin corrosion/irritation,
Category 2
H315 Causes skin irritation.Serious eye damage/eye
irritation, Category 2
H319 Causes serious eye irritation.Skin sensitisation,
Category 1
H317 May cause an allergic skin reaction.Reproductive toxicity,
Category 2
H361 Suspected of damaging fertility or the unborn child.Specific target organ
toxicity Single exposure,
Category 3, Respiratory
tract irritation
H335 May cause respiratory irritation.Specific target organ
toxicity Repeated
exposure, Category 1
H372 Causes damage to organs through prolonged or repeated exposure.Hazardous to the aquatic
environment Acute
Hazard, Category 2
H401 Toxic to aquatic life
Full text of H statements : see section 16
2.2. GHS Label elements, including precautionary statements
GHS US labelling
Hazard pictograms (GHS US) :Signal word (GHS US) :DangerHazard statements (GHS US) :H226 – Flammable liquid and vapour.
H315 – Causes skin irritation.

NPG Fast Putty
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
03/24/2021EN (English)2/11 H317 – May cause an allergic skin reaction.
H319 – Causes serious eye irritation.
H335 – May cause respiratory irritation.
H361 – Suspected of damaging fertility or the unborn child.
H372 – Causes damage to organs through prolonged or repeated exposure.
H401 – Toxic to aquatic life
Precautionary statements (GHS US) :P201 – Obtain special instructions before use.
P202 – Do not handle until all safety precautions have been read and understood.
P210 – Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No
smoking.
P233 – Keep container tightly closed.
P240 – Ground/Bond container and receiving equipment.
P241 – Use explosion-proof electrical, lighting, ventilating equipment.
P242 – Use only non-sparking tools.
P243 – Take precautionary measures against static discharge.
P260 – Do not breathe dust, fume, mist, spray, vapours.
P261 – Avoid breathing dust/fume/gas/mist/vapours/spray.
P264 – Wash EXPOSED AREA. thoroughly after handling.
P270 – Do not eat, drink or smoke when using this product.
P271 – Use only outdoors or in a well-ventilated area.
P272 – Contaminated work clothing must not be allowed out of the workplace.
P273 – Avoid release to the environment.
P280 – Wear eye protection, protective clothing, protective gloves.
P302+P352 – If on skin: Wash with plenty of water.
P303+P361+P353 – If on skin (or hair): Take off immediately all contaminated clothing. Rinse
skin with water/shower.
P304+P340 – If inhaled: Remove person to fresh air and keep comfortable for breathing.
P305+P351+P338 – IF IN EYES: Rinse cautiously with water for several minutes. Remove
contact lenses, if present and easy to do. Continue rinsing.
P308+P313 – If exposed or concerned: Get medical advice/attention.
P312 – Call a poison center or doctor if you feel unwell.
P314 – Get medical advice/attention if you feel unwell.
P321 – Specific treatment (see SEEK MEDICAL AID. on this label).
P332+P313 – If skin irritation occurs: Get medical advice/attention.
P333+P313 – If skin irritation or rash occurs: Get medical advice/attention.
P337+P313 – If eye irritation persists: Get medical advice/attention.
P362+P364 – Take off contaminated clothing and wash it before reuse.
P363 – Wash contaminated clothing before reuse.
P370+P378 – In case of fire: Use carbon dioxide (CO2), dry chemical powder, foam to
extinguish.
P403+P233 – Store in a well-ventilated place. Keep container tightly closed.
P403+P235 – Store in a well-ventilated place. Keep cool.
P405 – Store locked up.
P501 – Dispose of contents/container to LOCAL, STATE, AND NATIONAL REGULATIONS..
2.3. Other hazards which do not result in classification
No additional information available
2.4. Unknown acute toxicity (GHS US)
Not applicable
SECTION 3: Composition/information on ingredients
3.1. Substances
Not applicable
3.2. Mixtures
NameProduct identifier%GHS-US classificationUnsaturated Polyester Resin(CAS-No.) TRADE SECRET<= 60Not classifiedstyrene, inhibited(CAS-No.) 100-42-5<= 32Flam. Liq. 3, H226 Acute Tox. 4 (Inhalation), H332 Acute Tox. 4 (Inhalation:vapour), H332 Skin Irrit. 2, H315 Eye Irrit. 2A, H319 Carc. 2, H351 Repr. 2, H361 STOT SE 3, H335 STOT RE 1, H372 Aquatic Acute 2, H401 silicon dioxide, amorphous(CAS-No.) 7631-86-9<= 10Not classified NPG Fast Putty Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 03/24/2021EN (English)3/11 Name Product identifier % GHS-US classificationcobalt(II) 2-ethylhexanoate(CAS-No.) 136-52-7<= 0.5Eye Irrit. 2, H319 Skin Sens. 1, H317 Carc. 2, H351 Aquatic Acute 1, H400 Aquatic Chronic 2, H411 Full text of hazard classes and H-statements : see section 16 SECTION 4: First-aid measures 4.1. Description of first aid measures First-aid measures general :Never give anything by mouth to an unconscious person. IF exposed or concerned: Get medical advice/attention. First-aid measures after inhalation :Remove person to fresh air and keep comfortable for breathing. Remove person to fresh air and keep comfortable for breathing. Call a POISON CENTER/doctor if you feel unwell. First-aid measures after skin contact :Take off immediately all contaminated clothing. Rinse skin with water/shower. Wash with plenty of water/ . Wash contaminated clothing before reuse. If skin irritation occurs: Get medical advice/attention. Specific treatment (see supplemental first aid instruction on this label). First-aid measures after eye contact :Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention. First-aid measures after ingestion :Rinse mouth. Do NOT induce vomiting. Obtain emergency medical attention. Call a poison center or a doctor if you feel unwell. 4.2. Most important symptoms and effects (acute and delayed) Potential adverse human health effects and symptoms :Harmful if inhaled. Based on available data, the classification criteria are not met.Symptoms/effects :May cause genetic defects (avoid skin contact and inhalation.). May cause cancer (avoid skin contact and inhalation.). Suspected of damaging fertility or the unborn child. Causes damage to organs through prolonged or repeated exposure. Symptoms/effects after inhalation :Danger of serious damage to health by prolonged exposure through inhalation. Harmful if inhaled. May cause respiratory irritation. Symptoms/effects after skin contact :Causes skin irritation.Symptoms/effects after eye contact :Causes serious eye irritation. 4.3. Immediate medical attention and special treatment, if necessary Treat symptomatically. SECTION 5: Fire-fighting measures 5.1. Suitable (and unsuitable) extinguishing media Suitable extinguishing media :Sand. Water spray. Dry powder. Foam. Carbon dioxide.Unsuitable extinguishing media :Do not use a heavy water stream. 5.2. Specific hazards arising from the chemical Fire hazard :Highly flammable liquid and vapour. Flammable liquid and vapour.Explosion hazard :May form flammable/explosive vapour-air mixture.Reactivity in case of fire :No reactivity hazard other than the effects described in sub-sections below. 5.3. Special protective equipment and precautions for fire-fighters Firefighting instructions :Use water spray or fog for cooling exposed containers. Exercise caution when fighting any chemical fire. Prevent fire fighting water from entering the environment. Protection during firefighting :Do not enter fire area without proper protective equipment, including respiratory protection. Do not attempt to take action without suitable protective equipment. Self-contained breathing apparatus. Complete protective clothing. SECTION 6: Accidental release measures 6.1. Personal precautions, protective equipment and emergency procedures General measures :Remove ignition sources. Use special care to avoid static electric charges. No open flames. No smoking. 6.1.1.For non-emergency personnel Protective equipment :Gloves. Protective goggles. Protective clothing.Emergency procedures :Ventilate spillage area. Evacuate unnecessary personnel. NPG Fast Putty Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 03/24/2021EN (English)4/11 6.1.2.For emergency responders Protective equipment :Do not attempt to take action without suitable protective equipment. Equip cleanup crew with proper protection. For further information refer to section 8: "Exposure controls/personal protection". Emergency procedures :Ventilate area. 6.2. Environmental precautions Avoid release to the environment. Prevent entry to sewers and public waters. Notify authorities if liquid enters sewers or public waters. 6.3. Methods and material for containment and cleaning up For containment :Dam up the liquid spill. Contain released product, pump into suitable containers.Methods for cleaning up :Take up liquid spill into absorbent material. Soak up spills with inert solids, such as clay or diatomaceous earth as soon as possible. Collect spillage. Store away from other materials. Other information :Dispose of materials or solid residues at an authorized site. 6.4. Reference to other sections See Heading 8. Exposure controls and personal protection. For further information refer to section 13. SECTION 7: Handling and storage 7.1. Precautions for safe handling Additional hazards when processed :Handle empty containers with care because residual vapours are flammable.Precautions for safe handling :Wear personal protective equipment. Use only outdoors or in a well-ventilated area. Avoid breathing DUST, FUMES, MIST, OR VAPORS. Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Eliminate all ignition sources if safe to do so. Wash hands and other exposed areas with mild soap and water before eating, drinking or smoking and when leaving work. Provide good ventilation in process area to prevent formation of vapour. No open flames. No smoking. Take precautionary measures against static discharge. Use only non-sparking tools. Do not breathe dust/fume/gas/mist/vapours/spray. Hygiene measures :Wash hands, forearms and face thoroughly after handling. Do not eat, drink or smoke when using this product. Always wash hands after handling the product. 7.2. Conditions for safe storage, including any incompatibilities Technical measures :Proper grounding procedures to avoid static electricity should be followed. Ground/bond container and receiving equipment. Use explosion-proof electrical/ventilating/lighting equipment. Storage conditions :Keep in fireproof place. Keep only in the original container in a cool, well ventilated place away from : Keep container tightly closed. Store in a well-ventilated place. Keep cool. Incompatible products :Strong bases. Strong acids.Incompatible materials :Sources of ignition. Direct sunlight. Heat sources. SECTION 8: Exposure controls/personal protection 8.1. Control parameters styrene, inhibited (100-42-5)ACGIHACGIH TWA (ppm)20 ppmACGIHACGIH STEL (ppm)40 ppmcobalt(II) 2-ethylhexanoate (136-52-7)Not applicable Unsaturated Polyester Resin (TRADE SECRET)Not applicable silicon dioxide, amorphous (7631-86-9)Not applicable 8.2. Appropriate engineering controls Appropriate engineering controls :Ensure exposure is below occupational exposure limits (where available). Ensure good ventilation of the work station. Environmental exposure controls :Avoid release to the environment. NPG Fast Putty Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 03/24/2021EN (English)5/11 8.3. Individual protection measures/Personal protective equipment Personal protective equipment:Avoid all unnecessary exposure. Hand protection:Wear protective gloves.Eye protection:Chemical goggles or safety glasses. Safety glassesSkin and body protection:Wear suitable protective clothing Respiratory protection:Wear appropriate mask Other information:Do not eat, drink or smoke during use. SECTION 9: Physical and chemical properties 9.1. Information on basic physical and chemical properties Physical state :Liquid Colour :Colourless to yellow Odour :characteristic Odour threshold :No data available pH :No data available Melting point :Not applicable Freezing point :No data available Boiling point : 146.1 C Flash point :32.2 - 34 C Relative evaporation rate (butylacetate=1) :No data available Flammability (solid, gas) :Highly flammable liquid and vapour. Flammable liquid and vapour. Vapour pressure :No data available Relative vapour density at 20 C :No data available Relative density : 1.43 Solubility :No data available Log Pow :No data available Auto-ignition temperature :No data available Decomposition temperature :No data available Viscosity, kinematic :No data availableViscosity, dynamic :No data available Explosive limits :No data available Explosive properties :No data available Oxidising properties :No data available 9.2. Other information VOC content :<= 317 g/l SECTION 10: Stability and reactivity 10.1.Reactivity No reactivity hazard other than the effects described in sub-sections below. 10.2.Chemical stability Polymerization can result in formation of solid deposits, even in vapour space. Highly flammable liquid and vapour. Not established. Flammable liquid and vapour. May form flammable/explosive vapour-air mixture. NPG Fast Putty Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 03/24/2021EN (English)6/11 10.3.Possibility of hazardous reactions Not established. 10.4.Conditions to avoid Direct sunlight. Extremely high or low temperatures. Open flame. Overheating. Heat. Sparks. 10.5.Incompatible materials Strong acids. Strong bases. 10.6.Hazardous decomposition products fume. Carbon monoxide. Carbon dioxide. May release flammable gases. SECTION 11: Toxicological information 11.1.Information on toxicological effects Acute toxicity (oral) :Not classifiedAcute toxicity (dermal) :Not classifiedAcute toxicity (inhalation) :Not classifiedstyrene, inhibited (100-42-5)LD50 oral rat5000 mg/kg (Rat; Literature study; >6000 mg/kg bodyweight; Rat; Weight of evidence)LD50 dermal rat> 2000 mg/kg bodyweight (OECD 402: Acute Dermal Toxicity, 24 h, Rat, Male / female,
Experimental value, Dermal)
LD50 dermal rabbit5010 mg/kg (Rabbit; Literature study)LC50 Inhalation – Rat11.8 mg/l air (4 h, Rat, Inconclusive, insufficient data, Inhalation (vapours))LC50 Inhalation – Rat [ppm]2770 ppm/4h (Rat; Literature study)ATE US (oral)5000 mg/kg bodyweightATE US (dermal)5010 mg/kg bodyweightATE US (gases)2770 ppmv/4hATE US (vapours)11 mg/l/4hATE US (dust,mist)1.5 mg/l/4hcobalt(II) 2-ethylhexanoate (136-52-7)LD50 oral rat3129 mg/kg bodyweight (Rat; OECD 425: Acute Oral Toxicity: Up-and-Down Procedure;
Experimental value)
LD50 dermal rat> 2000 mg/kg bodyweight (Rat; Weight of evidence; OECD 402: Acute Dermal Toxicity)ATE US (oral)3129 mg/kg bodyweightsilicon dioxide, amorphous (7631-86-9)LD50 oral rat> 10000 mg/kg (Rat, Oral)LD50 dermal rabbit> 5000 mg/kg (Rabbit, Dermal)Skin corrosion/irritation :Causes skin irritation.Serious eye damage/irritation :Causes serious eye irritation.Respiratory or skin sensitisation :May cause an allergic skin reaction.Germ cell mutagenicity :Not classifiedCarcinogenicity :Not classified.styrene, inhibited (100-42-5)IARC group2B – Possibly carcinogenic to humansNational Toxicology Program (NTP) StatusReasonably anticipated to be Human Carcinogencobalt(II) 2-ethylhexanoate (136-52-7)IARC group2B – Possibly carcinogenic to humansReproductive toxicity :Suspected of damaging fertility or the unborn child.STOT-single exposure :May cause respiratory irritation.styrene, inhibited (100-42-5)STOT-single exposureMay cause respiratory irritation.STOT-repeated exposure :Causes damage to organs through prolonged or repeated exposure.

NPG Fast Putty
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
03/24/2021EN (English)7/11styrene, inhibited (100-42-5)STOT-repeated exposureCauses damage to organs through prolonged or repeated exposure.Aspiration hazard :Not classifiedViscosity, kinematic :No data availablePotential adverse human health effects and
symptoms
:Harmful if inhaled. Based on available data, the classification criteria are not met.Symptoms/effects :May cause genetic defects (avoid skin contact and inhalation.). May cause cancer (avoid skin
contact and inhalation.). Suspected of damaging fertility or the unborn child. Causes damage to
organs through prolonged or repeated exposure.
Symptoms/effects after inhalation :Danger of serious damage to health by prolonged exposure through inhalation. Harmful if
inhaled. May cause respiratory irritation.
Symptoms/effects after skin contact :Causes skin irritation.Symptoms/effects after eye contact :Causes serious eye irritation.
SECTION 12: Ecological information
12.1.Toxicity
Ecology – general :The product is not considered harmful to aquatic organisms nor to cause long-term adverse
effects in the environment.
styrene, inhibited (100-42-5)LC50 fish 110 mg/l (OECD 203: Fish, Acute Toxicity Test, 96 h, Pimephales promelas, Flow-through
system, Fresh water, Experimental value, GLP)
EC50 Daphnia 14.7 mg/l (OECD 202: Daphnia sp. Acute Immobilisation Test, 48 h, Daphnia magna, Flow-
through system, Fresh water, Experimental value, GLP)
ErC50 (algae)4.9 mg/l (EPA OTS 797.1050, 72 h, Pseudokirchneriella subcapitata, Static system, Fresh
water, Experimental value, GLP)
cobalt(II) 2-ethylhexanoate (136-52-7)LC50 fish 146.51 mg/l (LOEC; ASTM; 96 h; Pimephales promelas; Flow-through system; Fresh water;
Read-across)
EC50 Daphnia 10.212 mg/l (NOEC; ASTM; 48 h; Ceriodaphnia dubia; Static system; Salt water; Read-across)LC50 fish 254.1 mg/l (LC50; ASTM; 96 h; Pimephales promelas; Flow-through system; Fresh water;
Read-across)
EC50 Daphnia 20.605 mg/l (LC50; ASTM; 48 h; Ceriodaphnia dubia; Static system; Salt water; Read-across)Threshold limit algae 1144 g/l (ErC50; OECD 201: Alga, Growth Inhibition Test; 72 h; Pseudokirchneriella
subcapitata; Static system; Fresh water; Read-across)
Threshold limit algae 232.2 g/l (NOEC; OECD 201: Alga, Growth Inhibition Test; 72 h; Pseudokirchneriella
subcapitata; Static system; Fresh water; Read-across)
silicon dioxide, amorphous (7631-86-9)LC50 fish 1> 10000 mg/l (96 h, Brachydanio rerio, Literature)EC50 Daphnia 1> 10000 mg/l (24 h, Daphnia magna, Literature)
12.2.Persistence and degradability
NPG Fast Putty (mixture)Persistence and degradabilityNot established.styrene, inhibited (100-42-5)Persistence and degradabilityBiodegradable in the soil. Readily biodegradable in water.Chemical oxygen demand (COD)
2.8 g O /g substance
ThOD
3.07 g O /g substance
BOD (% of ThOD)0.42 (Literature study)cobalt(II) 2-ethylhexanoate (136-52-7)Persistence and degradabilityReadily biodegradable in water. No (test)data on mobility of the substance available.Unsaturated Polyester Resin (TRADE SECRET)Persistence and degradabilityNot established.silicon dioxide, amorphous (7631-86-9)Persistence and degradabilityBiodegradability in soil: not applicable. Biodegradability: not applicable.

NPG Fast Putty
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
03/24/2021EN (English)8/11
silicon dioxide, amorphous (7631-86-9)
Chemical oxygen demand (COD)
Not applicable (inorganic)
ThOD
Not applicable (inorganic)
12.3.Bioaccumulative potential
NPG Fast Putty (mixture)Bioaccumulative potentialNot established.styrene, inhibited (100-42-5)BCF fish 135.5 (Carassius auratus, Literature study)Log Pow2.96 (Experimental value, OECD 107: Partition Coefficient (n-octanol/water): Shake Flask
Method, 25 C)
Bioaccumulative potentialLow potential for bioaccumulation (Log Kow < 4).cobalt(II) 2-ethylhexanoate (136-52-7)BCF fish 11.2 (BCF; 131 days; Seriola quinqueradiata; Static system; Salt water; Read-across)Bioaccumulative potentialLow potential for bioaccumulation (BCF < 500).Unsaturated Polyester Resin (TRADE SECRET)Bioaccumulative potentialNot established.silicon dioxide, amorphous (7631-86-9)Bioaccumulative potentialNot bioaccumulative. 12.4.Mobility in soil styrene, inhibited (100-42-5)Surface tension0.032 N/m (20 C)Log Koc2.55 (log Koc, Estimated value)Ecology - soilLow potential for adsorption in soil.cobalt(II) 2-ethylhexanoate (136-52-7)Surface tension0.064 N/m (20 C; 1 g/l)silicon dioxide, amorphous (7631-86-9)Ecology - soilNo (test)data on mobility of the substance available. 12.5.Other adverse effects Other information :Avoid release to the environment. SECTION 13: Disposal considerations 13.1.Disposal methods Waste treatment methods :Dispose of contents/container in accordance with licensed collector s sorting instructions.Product/Packaging disposal recommendations :Dispose in a safe manner in accordance with local/national regulations. Dispose of contents/container to hazardous or special waste collection point, in accordance with local, regional, national and/or international regulation. Additional information :Handle empty containers with care because residual vapours are flammable.Ecology - waste materials :Avoid release to the environment. SECTION 14: Transport information Department of Transportation (DOT) In accordance with DOTProper Shipping Name (DOT) :RESIN SOLUTION Class (DOT) :3 - Class 3 - Flammable and combustible liquid 49 CFR 173.120 Packing group (DOT) :II - Medium Danger NPG Fast Putty Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 03/24/2021EN (English)9/11Hazard labels (DOT) :3 - Flammable liquid Other information :No supplementary information available. Transportation of Dangerous GoodsTransport by sea Transport document description (IMDG) :UN 1866 RESIN SOLUTION, 3, IIIUN-No. (IMDG) :1866Proper Shipping Name (IMDG) :RESIN SOLUTIONClass (IMDG) :3 - Flammable liquidsPacking group (IMDG) :III - substances presenting low danger Air transport Transport document description (IATA) :UN 1866 RESIN SOLUTION, 3, IIIUN-No. (IATA) :1866Proper Shipping Name (IATA) :RESIN SOLUTIONClass (IATA) :3 - Flammable LiquidsPacking group (IATA) :III - Minor Danger SECTION 15: Regulatory information 15.1. US Federal regulations styrene, inhibited (100-42-5)Listed on the United States TSCA (Toxic Substances Control Act) inventory Subject to reporting requirements of United States SARA Section 313 Listed on EPA Hazardous Air Pollutant (HAPS) CERCLA RQ1000 lbSARA Section 311/312 Hazard ClassesImmediate (acute) health hazard Reactive hazard - No Fire hazard Delayed (chronic) health hazard cobalt(II) 2-ethylhexanoate (136-52-7)Listed on the United States TSCA (Toxic Substances Control Act) inventory 15.2. International regulations CANADA styrene, inhibited (100-42-5)Listed on the Canadian DSL (Domestic Substances List)cobalt(II) 2-ethylhexanoate (136-52-7)Listed on the Canadian DSL (Domestic Substances List)Unsaturated Polyester Resin (TRADE SECRET)Not listed on the Canadian DSL (Domestic Substances List)/NDSL (Non-Domestic Substances List) EU-Regulations No additional information available National regulations styrene, inhibited (100-42-5)Listed on IARC (International Agency for Research on Cancer) Listed as carcinogen on NTP (National Toxicology Program) NPG Fast Putty Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 03/24/2021EN (English)10/11 15.3. US State regulations styrene, inhibited (100-42-5)U.S. - California - Proposition 65 - Carcinogens List U.S. - California - Proposition 65 - Developmental Toxicity U.S. - California - Proposition 65 - Reproductive Toxicity - Female U.S. - California - Proposition 65 - Reproductive Toxicity - Male No significant risk level (NSRL) Maximum allowable dose level (MADL) YesNoNoNo27 g/dayComponentState or local regulationsstyrene, inhibited(100-42-5)U.S. - Massachusetts - Right To Know List; U.S. - New Jersey - Right to Know Hazardous Substance List; U.S. - Pennsylvania - RTK (Right to Know) List SECTION 16: Other information according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations Other information :None. Full text of H-statements:H226Flammable liquid and vapour.H315Causes skin irritation.H317May cause an allergic skin reaction.H319Causes serious eye irritation.H332Harmful if inhaled.H335May cause respiratory irritation.H351Suspected of causing cancer.H361Suspected of damaging fertility or the unborn child.H372Causes damage to organs through prolonged or repeated exposure.H400Very toxic to aquatic life.H401Toxic to aquatic lifeH411Toxic to aquatic life with long lasting effects. NFPA health hazard :2 - Materials that, under emergency conditions, can cause temporary incapacitation or residual injury. NFPA fire hazard :3 - Liquids and solids (including finely divided suspended solids) that can be ignited under almost all ambient temperature conditions. NFPA reactivity :2 - Materials that readily undergo violent chemical change at elevated temperatures and pressures. Hazard RatingHealth :2 Moderate Hazard - Temporary or minor injury may occurFlammability :3 Serious Hazard - Materials capable of ignition under almost all normal temperature conditions. Includes flammable liquids with flash points below 73 F and boiling points above 100 F. as well as liquids with flash points between 73 F and 100 F. (Classes IB & IC) Physical :1 Slight Hazard - Materials that are normally stable but can become unstable (self-react) at high temperatures and pressures. Materials may react non-violently with water or undergo hazardous polymerization in the absence of inhibitors. :HPersonal protection H - Splash goggles, Gloves, Synthetic apron, Vapor respirator SDS US (GHS HazCom 2012) NPG Fast Putty Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 03/24/2021EN (English)11/11 To the best of our knowledge this SDS is accurate. The the extent allowed by law, this statement is made in lieu of an other warranties, expressed or implied including but not limited to any implied warranty of merchantability or fitness for a particular purpose and is in lieu of any other obligations or liability on the part of Dura Technoligies, Inc.