08A8888_TDS.pdf

by | Sep 27, 2025

TECHNICAL DATA SHEE T
A8888
RELEASE FABRIC

Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA

TDS A8888_02 .21_Issue1

A8888
Release fabric
Ideally suited to medium temperature applications
Features and Benefits
Silicone coated nylon fabric.
Coated with heat cured silicone release solution, to
aid removal from the cured laminate.
Some phenolic resins are known to adhere to nylon
release fabrics, and it is therefore recommended that
the customer conduct their own internal compatibility
tests.
When using release fabrics on composite laminates
that will be subject to secondary bonding or painting
operations, there is a potential for minor transfer onto
the component, despite the release solution being fully
polymerised. It is therefore recommended that prior to
bonding or painting the laminate should be suitable
prepared (industry standard method is preparation by
slight abrading or sanding of the surface followed by
cleaning with an approved solvent).
PROPERTIES
Maximum cure temperature 204 C 400 F
Color
White with red pinstripes
(Green is also available on request)
Fabric type Nylon
Fabric weight 75g/m 2.2oz/yd
Release coating Silicone
AVAILABILITY
Standard width 1.52m 60in
Standard length 100m 109yd
Slit widths available
STORAGE
No special storage conditions required.
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.

DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.

08AB80_TDS.pdf

by | Sep 27, 2025

TECHNICAL DATA SHEE T
AB80
BREATHER FABRIC

Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA

TDS AB80_02.21_Issue1

AB80
Breather fabric
Ideally suited to aerospace applications

Features and Benefits
Non-woven polyester breather fabric.
This product is mechanically bonded by needling.
Lightweight highly conformable breather.

PROPERTIES

Maximum use temperature 204 C 400 F
Color White
Fiber Polyester
Weight 80g/m 2.6oz/yd
AVAILABILITY

Standard width Up to 1.52m Up to 6in
Standard length Up to 100m Up to 109yd
Cut shapes/slit widths Available to order
STORAGE
No special storage conditions required.
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.

DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.

08A6200_TDS.pdf

by | Sep 27, 2025

TECHNICAL DATA SHEE T
VAC-PAK

A6200/A6200M & A6000
RELEASE FILM

Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA

TDS VPK A6200/A6200M & A6000_0 2.21_Issue1

VAC-PAK

A6200/A6200M & A6000
Release film
Ideally suited to aerospace applications
Features and Benefits
High temperature, tough fluropolymer release
films with excellent release characteristics
combined with high elongation.
Suitable for use with all commonly used resin
systems.
Available perforated or non- perforated
Most commonly used in aerospace applications
and has numerous OEM approvals.
Clear blue or red for ease of identification on the
cured laminate.
Vac-Pak

A6200M has a one-sided textured finish
to meet matte surface finish requirements
PROPERTIES
Melting point 262 C 503 F
Color Clear blue and red
Film ETFE
Standard perforation patterns Contact us for full details
Tensile strength (at break) 40/70MPa 6000/10000psi
Elongation (at break) 350%
Yield 10.2m /kg 110 ft /lb/mil
The user shall determine the suitability of the products for their intended use prior to purchase and shall assume all
risk and liability in connection therewith.

AVAILABILITY Thicknesses 12, 15, 20 and 25 m 0.0005, 0.0006, 0.001 and 0.002in
Standard length Available on request
STORAGE
Store in original packaging
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.

DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.

08A6200PR_TDS.pdf

by | Sep 27, 2025

TECHNICAL DATA SHEE T
VAC-PAK

A6200/A6200M & A6000
RELEASE FILM

Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA

TDS VPK A6200/A6200M & A6000_0 2.21_Issue1

VAC-PAK

A6200/A6200M & A6000
Release film
Ideally suited to aerospace applications
Features and Benefits
High temperature, tough fluropolymer release
films with excellent release characteristics
combined with high elongation.
Suitable for use with all commonly used resin
systems.
Available perforated or non- perforated
Most commonly used in aerospace applications
and has numerous OEM approvals.
Clear blue or red for ease of identification on the
cured laminate.
Vac-Pak

A6200M has a one-sided textured finish
to meet matte surface finish requirements
PROPERTIES
Melting point 262 C 503 F
Color Clear blue and red
Film ETFE
Standard perforation patterns Contact us for full details
Tensile strength (at break) 40/70MPa 6000/10000psi
Elongation (at break) 350%
Yield 10.2m /kg 110 ft /lb/mil
The user shall determine the suitability of the products for their intended use prior to purchase and shall assume all
risk and liability in connection therewith.

AVAILABILITY Thicknesses 12, 15, 20 and 25 m 0.0005, 0.0006, 0.001 and 0.002in
Standard length Available on request
STORAGE
Store in original packaging
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.

DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.

08A6200P8R_TDS.pdf

by | Sep 27, 2025

TECHNICAL DATA SHEE T
VAC-PAK

A6200/A6200M & A6000
RELEASE FILM

Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA

TDS VPK A6200/A6200M & A6000_0 2.21_Issue1

VAC-PAK

A6200/A6200M & A6000
Release film
Ideally suited to aerospace applications
Features and Benefits
High temperature, tough fluropolymer release
films with excellent release characteristics
combined with high elongation.
Suitable for use with all commonly used resin
systems.
Available perforated or non- perforated
Most commonly used in aerospace applications
and has numerous OEM approvals.
Clear blue or red for ease of identification on the
cured laminate.
Vac-Pak

A6200M has a one-sided textured finish
to meet matte surface finish requirements
PROPERTIES
Melting point 262 C 503 F
Color Clear blue and red
Film ETFE
Standard perforation patterns Contact us for full details
Tensile strength (at break) 40/70MPa 6000/10000psi
Elongation (at break) 350%
Yield 10.2m /kg 110 ft /lb/mil
The user shall determine the suitability of the products for their intended use prior to purchase and shall assume all
risk and liability in connection therewith.

AVAILABILITY Thicknesses 12, 15, 20 and 25 m 0.0005, 0.0006, 0.001 and 0.002in
Standard length Available on request
STORAGE
Store in original packaging
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.

DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.

08A6200P8B_TDS.pdf

by | Sep 27, 2025

TECHNICAL DATA SHEE T
VAC-PAK

A6200/A6200M & A6000
RELEASE FILM

Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA

TDS VPK A6200/A6200M & A6000_0 2.21_Issue1

VAC-PAK

A6200/A6200M & A6000
Release film
Ideally suited to aerospace applications
Features and Benefits
High temperature, tough fluropolymer release
films with excellent release characteristics
combined with high elongation.
Suitable for use with all commonly used resin
systems.
Available perforated or non- perforated
Most commonly used in aerospace applications
and has numerous OEM approvals.
Clear blue or red for ease of identification on the
cured laminate.
Vac-Pak

A6200M has a one-sided textured finish
to meet matte surface finish requirements
PROPERTIES
Melting point 262 C 503 F
Color Clear blue and red
Film ETFE
Standard perforation patterns Contact us for full details
Tensile strength (at break) 40/70MPa 6000/10000psi
Elongation (at break) 350%
Yield 10.2m /kg 110 ft /lb/mil
The user shall determine the suitability of the products for their intended use prior to purchase and shall assume all
risk and liability in connection therewith.

AVAILABILITY Thicknesses 12, 15, 20 and 25 m 0.0005, 0.0006, 0.001 and 0.002in
Standard length Available on request
STORAGE
Store in original packaging
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.

DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.