08SM5142BY_SDS.pdf

by | Sep 27, 2025

SAFETY DATA SHEET
Date Prepared : 09/13/2017
MSDS No : SM5142
Date Revised : 09/13/2017
Revision No : 8
TACKY TAPE SM5142BY
1. PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: TACKY TAPE SM5142BY
MANUFACTURER 24 HR. EMERGENCY TELEPHONE NUMBERS
ITW Polymers Sealants North America
111 South Nursery Road
Irving, TX 75060
Product Stewardship: (972) 438-9111
CHEMTREC (US Transportation): (800) 424-9300
COMMENTS: TACKY TAPE is a registered trademark of Illinois Tool Works, Inc.
2. HAZARDS IDENTIFICATION
GHS CLASSIFICATIONS
Not classified
GHS LABEL
No labeling applicable
EMERGENCY OVERVIEW
PHYSICAL APPEARANCE: Bright Yellow
IMMEDIATE CONCERNS: Solid tape packages in rolls with release paper.
POTENTIAL HEALTH EFFECTS
EYES: Contact may cause moderate eye irritation.
SKIN: Repeated or prolonged skin contact may result in allergic dermatitis. If product is hot, contact with the
skin will result in thermal burns.
INGESTION: Not likely route of entry.
INHALATION: Not likely route of entry.
CARCINOGENICITY: This product is not known to contain any components at concentrations above 0.1% which
are considered carcinogenic by OSHA, IARC or NTP.
3. COMPOSITION / INFORMATION ON INGREDIENTS
Chemical Name Wt.% CAS
Talc 5 – 1514807-96-6
4. FIRST AID MEASURES
EYES: Flush eye with tempered water for 15 minutes lifting upper and lower eye lids occasionally. If irritation
persists, contact a physician.
SKIN: Remove contaminated clothing. Immediately wash exp osed area with large amounts of water. If hot
material adheres to the skin, do not attempt to peal off material. Cool the hot material with water and cover with
a dry sterile dressing. Seek medical attention.
INGESTION: Do not induce vomiting. Get medical attention immediately. Never give anything by mouth to an
unconscious person.
Page 1 of 5

SAFETY DATA SHEET
Date Prepared : 09/13/2017
MSDS No : SM5142
Date Revised : 09/13/2017
Revision No : 8
TACKY TAPE SM5142BY
INHALATION: Under normal conditions of use, inhalation of product is unlikely. If fumes are inhaled and become
irritant, remove person from the area to fresh air. Seek immediate medical attention if exposure has occurred.
NOTES TO PHYSICIAN: Treat symptomatically.
5. FIRE FIGHTING MEASURES
FLAMMABLE CLASS: None
GENERAL HAZARD: Non Hazardous
EXTINGUISHING MEDIA: Use methods appropriate for the surrounding fire. Water spray, dry chemical, carbon
dioxide, AFFF or alcohol resistant foams are all appropriate.
EXPLOSION HAZARDS: Low hazard
FIRE FIGHTING PROCEDURES: As in any fire, wear self-contained breathing apparatus with pressure-demand,
full face piece SCBA (MSHA/NIOSH approved or equiva lent) and full protective gear.
6. ACCIDENTAL RELEASE MEASURES
SMALL SPILL: This material is a solid tape product and release to the environment is highly unlikely. Containment
is not necessary, this product will not flow. Use appropriate personal protective equipment (PPE) when handling
product. Only employees properly trained should be part of any containment or spill response.
LARGE SPILL: Refer to release measures under small spill, large spills are to be handled in the same manner.
7. HANDLING AND STORAGE
HANDLING: Use good chemcial handling procedures and practices. No special handling precautions are required.
STORAGE: Store at or under 80 degrees F. Do not stack cartons on end. Rotate stock.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
EXPOSURE GUIDELINES
OSHA HAZARDOUS COMPONENTS (29 CFR1910.1200)
EXPOSURE LIMITS
Chemical Name Type ppm mg/m
3
Talc
OSHA PEL
TWA 20 mpp 3.3 mg/m3
STEL NL
[1]
NL
[1]
ACGIH TLV
TWA NL
[1]
2 mg/m3
[1]
STEL NL
[1]
NL
[1]
Footnotes:
1. NL = Not Listed
ENGINEERING CONTROLS: Natural ventilation should be adequate under normal conditions.
PERSONAL PROTECTIVE EQUIPMENT
EYES AND FACE: Wear safety glasses with side shields.
SKIN: Wear chemical resistant, impervious gloves.
Page 2 of 5

SAFETY DATA SHEET
Date Prepared : 09/13/2017
MSDS No : SM5142
Date Revised : 09/13/2017
Revision No : 8
TACKY TAPE SM5142BY
RESPIRATORY: No respiratory protection required under normal conditions.
WORK HYGIENIC PRACTICES: Use good hygiene practices when handling this material. Wash hands thoroughly
after use.
9. PHYSICAL AND CHEMICAL PROPERTIES
PHYSICAL STATE: Solid
ODOR: None
ODOR THRESHOLD: Not Determined
COLOR: Bright Yellow
PHYSICAL STATE COMMENTS: Tape material
pH: 7.02
PERCENT VOLATILE: > 99% by weight solid
FLASHPOINT AND METHOD: Not Applicable
FLAMMABLE LIMITS: No data
AUTOIGNITION TEMPERATURE: Not Applicable
VAPOR PRESSURE: Not Determined
VAPOR DENSITY: Not Determined
BOILING POINT: Not Determined
FREEZING POINT: Not Determined
MELTING POINT: Not Determined
POUR POINT: Not Determined
SOLUBILITY IN WATER: Nonsoluble
PARTITION COEFFICIENT: N-OCTANOL/WATER: Not Determined
EVAPORATION RATE: Not Determined
DENSITY: 10.25 lbs/gal
PARTICLE SIZE: Not Determined
SPECIFIC GRAVITY: 1.23
VISCOSITY: Not Determined
MOLECULAR WEIGHT: Not Determined
(VOC): < 1 % OXIDIZING PROPERTIES: Not Determined 10. STABILITY AND REACTIVITY REACTIVITY: Yes HAZARDOUS POLYMERIZATION: Product will not undergo polymerization. STABILITY: Stable. CONDITIONS TO AVOID: No conditions known POSSIBILITY OF HAZARDOUS REACTIONS: None HAZARDOUS DECOMPOSITION PRODUCTS: Carbon dioxide, carbon monoxide, hydrogen chloride and sulfides. Page 3 of 5 SAFETY DATA SHEET Date Prepared : 09/13/2017 MSDS No : SM5142 Date Revised : 09/13/2017 Revision No : 8 TACKY TAPE SM5142BY INCOMPATIBLE MATERIALS: Liquid chlorine, potassium permanganate, fuming nitric acid, fluorine and other strong oxidizing and base agents. 11. TOXICOLOGICAL INFORMATION ACUTE TOXICITY Chemical Name ORAL LD50 (rat) DERMAL LD 50 (rabbit) INHALATION LC 50 (rat) Talc No data No data No data NOTES: No known acute effects. 12. ECOLOGICAL INFORMATION ENVIRONMENTAL DATA: No environmental information was found for this product. ECOTOXICOLOGICAL INFORMATION: No ecotoxicity data was found for this product. BIOACCUMULATION/ACCUMULATION: Contains components with the potential to bio-accumulate. 13. DISPOSAL CONSIDERATIONS DISPOSAL METHOD: Consult with the US EPA Guidelines listed in 40 CFR Part 261.3 for the classifications of hazardous waste prior to disposal. Consult with your state and local hazardous waste requirements or guidelines to ensure compliance. Arrange disposal in accordance with EPA, state and local requirements. 14. TRANSPORT INFORMATION DOT (DEPARTMENT OF TRANSPORTATION) PROPER SHIPPING NAME: Not Regulated for Transport PRIMARY HAZARD CLASS/DIVISION: Not Regulated UN/NA NUMBER: NA PACKING GROUP: NA 15. REGULATORY INFORMATION UNITED STATES SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZ ATION ACT) FIRE: No PRESSURE GENERATING: No REACTIVITY: No ACUTE: No CHRONIC: No TSCA (TOXIC SUBSTANCE CONTROL ACT) Chemical Name CAS Talc 14807-96-6 16. OTHER INFORMATION Date Revised: 09/13/2017 INFORMATION CONTACT: (972) 438-9111 REVISION SUMMARY: This MSDS replaces the 10/19/2016 MSDS. Revised: Section 1: Date Issued. Page 4 of 5 SAFETY DATA SHEET Date Prepared : 09/13/2017 MSDS No : SM5142 Date Revised : 09/13/2017 Revision No : 8 TACKY TAPE SM5142BY HMIS RATING HEALTH * 0 FLAMMABILITY 1 PHYSICAL HAZARD 0 PERSONAL PROTECTION B NFPA CODES 1 0 0 GENERAL STATEMENTS: Keep out of reach of children For professional or industrial use only MANUFACTURER DISCLAIMER: This document may be used to comply with OSHA's Ha zardous Communication Standard, 29 CFR 1910.1200. To the best of our knowledge, the information contained in this SDS is accurate. It is intended to assist the user in his/her evaluation of the product's hazards and safety precautions to be taken in its use. The data in this SDS relate only to the specific material designated herein. We do not assume liability for the use of, or reliance on this information, nor do we guarantee its accuracy or completeness. This information is furnished without warranty, expressed or implied, except that it is accurate to the best knowledge of ITW Polymers Sealants North America. The data on this sheet relates only to the specific material designated herein. ITW Polymers Sealants North America assumes no legal responsibility for use or reliance upon these data. Page 5 of 5

08SM512710_SDS.pdf

by | Sep 27, 2025

SAFETY DATA SHEET
Date Prepared : 05/07/2019
MSDS No : SM5127
Date Revised : 05/07/2019
Revision No : 8
TACKY TAPE SM5127
1. PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: TACKY TAPE SM5127
ALTERNATE TRADE NAME(S): Vacuum Bag Tape Sealant
MANUFACTURER 24 HR. EMERGENCY TELEPHONE NUMBERS
ITW Polymers Sealants North America
111 South Nursery Road
Irving, TX 75060
Product Stewardship: (972) 438-9111
CHEMTREC (US Transportation): (800) 424-9300
COMMENTS: TACKY TAPE is a registered trademark of Illinois Tool Works, Inc.
2. HAZARDS IDENTIFICATION
GHS CLASSIFICATIONS
Not classified
GHS LABEL
No labeling applicable
EMERGENCY OVERVIEW
PHYSICAL APPEARANCE: Dark Gray
IMMEDIATE CONCERNS: Solid tape packages in rolls with release paper.
POTENTIAL HEALTH EFFECTS
EYES: Contact may cause moderate eye irritation.
SKIN: Repeated or prolonged skin contact may result in allergic dermatitis. If product is hot, contact with the
skin will result in thermal burns.
INGESTION: Not likely route of entry.
INHALATION: Not likely route of entry.
CARCINOGENICITY: This product is not known to contain any components at concentrations above 0.1% which
are considered carcinogenic by OSHA, IARC or NTP.
3. COMPOSITION / INFORMATION ON INGREDIENTS
Chemical Name Wt.% CAS
Talc 5 – 1514807-96-6
4. FIRST AID MEASURES
EYES: Flush eye with tempered water for 15 minutes lifting upper and lower eye lids occasionally. If irritation
persists, contact a physician.
SKIN: Remove contaminated clothing. Immediately wash exp osed area with large amounts of water. If hot
material adheres to the skin, do not attempt to peal off material. Cool the hot material with water and cover with
a dry sterile dressing. Seek medical attention.
INGESTION: Do not induce vomiting. Get medical attention immediately. Never give anything by mouth to an
unconscious person.
Page 1 of 5

SAFETY DATA SHEET
Date Prepared : 05/07/2019
MSDS No : SM5127
Date Revised : 05/07/2019
Revision No : 8
TACKY TAPE SM5127
INHALATION: Under normal conditions of use, inhalation of product is unlikely. If fumes are inhaled and become
irritant, remove person from the area to fresh air. Seek immediate medical attention if exposure has occurred.
NOTES TO PHYSICIAN: Treat symptomatically.
5. FIRE FIGHTING MEASURES
FLAMMABLE CLASS: None
GENERAL HAZARD: Non Hazardous
EXTINGUISHING MEDIA: Use methods appropriate for the surrounding fire. Water spray, dry chemical, carbon
dioxide, AFFF or alcohol resistant foams are all appropriate.
EXPLOSION HAZARDS: Low hazard
FIRE FIGHTING PROCEDURES: As in any fire, wear self-contained breathing apparatus with pressure-demand,
full face piece SCBA (MSHA/NIOSH approved or equiva lent) and full protective gear.
6. ACCIDENTAL RELEASE MEASURES
SMALL SPILL: This material is a solid tape product and release to the environment is highly unlikely. Containment
is not necessary, this product will not flow. Use appropriate personal protective equipment (PPE) when handling
product. Only employees properly trained should be part of any containment or spill response.
LARGE SPILL: Refer to release measures under small spill, large spills are to be handled in the same manner.
7. HANDLING AND STORAGE
HANDLING: Use good chemcial handling procedures and practices. No special handling precautions are required.
STORAGE: Store at or under 80 degrees F. Do not stack cartons on end. Rotate stock.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
EXPOSURE GUIDELINES
OSHA HAZARDOUS COMPONENTS (29 CFR1910.1200)
EXPOSURE LIMITS
Chemical Name Type ppm mg/m
3
Talc
OSHA PEL
TWA 20 mpp 3.3 mg/m3
STEL NL
[1]
NL
[1]
ACGIH TLV
TWA NL
[1]
2 mg/m3
[1]
STEL NL
[1]
NL
[1]
Footnotes:
1. NL = Not Listed
ENGINEERING CONTROLS: Natural ventilation should be adequate under normal conditions.
PERSONAL PROTECTIVE EQUIPMENT
EYES AND FACE: Wear safety glasses with side shields.
SKIN: Wear chemical resistant, impervious gloves.
Page 2 of 5

SAFETY DATA SHEET
Date Prepared : 05/07/2019
MSDS No : SM5127
Date Revised : 05/07/2019
Revision No : 8
TACKY TAPE SM5127
RESPIRATORY: No respiratory protection required under normal conditions.
WORK HYGIENIC PRACTICES: Use good hygiene practices when handling this material. Wash hands thoroughly
after use.
9. PHYSICAL AND CHEMICAL PROPERTIES
PHYSICAL STATE: Solid
ODOR: None
ODOR THRESHOLD: Not Determined
COLOR: Dark Gray
PHYSICAL STATE COMMENTS: Tape material
pH: 7.02
PERCENT VOLATILE: > 99% by weight solid
FLASHPOINT AND METHOD: Not Applicable
FLAMMABLE LIMITS: No data
AUTOIGNITION TEMPERATURE: Not Applicable
VAPOR PRESSURE: Not Determined
VAPOR DENSITY: Not Determined
BOILING POINT: Not Determined
FREEZING POINT: Not Determined
MELTING POINT: Not Determined
POUR POINT: Not Determined
SOLUBILITY IN WATER: Nonsoluble
PARTITION COEFFICIENT: N-OCTANOL/WATER: Not Determined
EVAPORATION RATE: Not Determined
DENSITY: 10.25 lbs/gal
PARTICLE SIZE: Not Determined
SPECIFIC GRAVITY: 1.23
VISCOSITY: Not Determined
MOLECULAR WEIGHT: Not Determined
(VOC): < 1 % OXIDIZING PROPERTIES: Not Determined 10. STABILITY AND REACTIVITY REACTIVITY: Yes HAZARDOUS POLYMERIZATION: Product will not undergo polymerization. STABILITY: Stable. CONDITIONS TO AVOID: No conditions known POSSIBILITY OF HAZARDOUS REACTIONS: None HAZARDOUS DECOMPOSITION PRODUCTS: Carbon dioxide, carbon monoxide, hydrogen bromide and sulfides. Page 3 of 5 SAFETY DATA SHEET Date Prepared : 05/07/2019 MSDS No : SM5127 Date Revised : 05/07/2019 Revision No : 8 TACKY TAPE SM5127 INCOMPATIBLE MATERIALS: Liquid chlorine, potassium permanganate, fuming nitric acid, fluorine and other strong oxidizing and base agents. 11. TOXICOLOGICAL INFORMATION ACUTE TOXICITY Chemical Name ORAL LD50 (rat) DERMAL LD 50 (rabbit) INHALATION LC 50 (rat) Talc No data No data No data NOTES: No known acute effects. 12. ECOLOGICAL INFORMATION ENVIRONMENTAL DATA: No environmental information was found for this product. ECOTOXICOLOGICAL INFORMATION: No ecotoxicity data was found for this product. BIOACCUMULATION/ACCUMULATION: Contains components with the potential to bio-accumulate. 13. DISPOSAL CONSIDERATIONS DISPOSAL METHOD: Consult with the US EPA Guidelines listed in 40 CFR Part 261.3 for the classifications of hazardous waste prior to disposal. Consult with your state and local hazardous waste requirements or guidelines to ensure compliance. Arrange disposal in accordance with EPA, state and local requirements. 14. TRANSPORT INFORMATION DOT (DEPARTMENT OF TRANSPORTATION) PROPER SHIPPING NAME: Not Regulated for Transport PRIMARY HAZARD CLASS/DIVISION: Not Regulated UN/NA NUMBER: NA PACKING GROUP: NA 15. REGULATORY INFORMATION UNITED STATES SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZ ATION ACT) FIRE: No PRESSURE GENERATING: No REACTIVITY: No ACUTE: No CHRONIC: No TSCA (TOXIC SUBSTANCE CONTROL ACT) Chemical Name CAS Talc 14807-96-6 16. OTHER INFORMATION Date Revised: 05/07/2019 INFORMATION CONTACT: (972) 438-9111 REVISION SUMMARY: This MSDS replaces the 09/13/2017 MSDS. Revised: Section 1: Date Issued. Section Page 4 of 5 SAFETY DATA SHEET Date Prepared : 05/07/2019 MSDS No : SM5127 Date Revised : 05/07/2019 Revision No : 8 TACKY TAPE SM5127 10: HAZARDOUS DECOMPOSITION PRODUCTS. HMIS RATING HEALTH * 0 FLAMMABILITY 1 PHYSICAL HAZARD 0 PERSONAL PROTECTION B NFPA CODES 1 0 0 GENERAL STATEMENTS: Keep out of reach of children For professional or industrial use only MANUFACTURER DISCLAIMER: This document may be used to comply with OSHA's Ha zardous Communication Standard, 29 CFR 1910.1200. To the best of our knowledge, the information contained in this SDS is accurate. It is intended to assist the user in his/her evaluation of the product's hazards and safety precautions to be taken in its use. The data in this SDS relate only to the specific material designated herein. We do not assume liability for the use of, or reliance on this information, nor do we guarantee its accuracy or completeness. This information is furnished without warranty, expressed or implied, except that it is accurate to the best knowledge of ITW Polymers Sealants North America. The data on this sheet relates only to the specific material designated herein. ITW Polymers Sealants North America assumes no legal responsibility for use or reliance upon these data. Page 5 of 5

08RS200_SDS.pdf

by | Sep 27, 2025

SAFETY DATA SHEET
Date Prepared : 09/13/2017
MSDS No : SM7191
Date Revised : 09/13/2017
Revision No : 1
TACKY TAPE SM7191 Vacuum Bag Sealant Tape
1. PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: TACKY TAPE SM7191 Vacuum Bag Sealant Tape
MANUFACTURER 24 HR. EMERGENCY TELEPHONE NUMBERS
ITW Polymers Sealants North America
111 South Nursery Road
Irving, TX 75060
Product Stewardship: (972) 438-9111
CHEMTREC (US Transportation): (800) 424-9300
COMMENTS: TACKY TAPE is a registered trademark of Illinois Tool Works, Inc.
2. HAZARDS IDENTIFICATION
GHS CLASSIFICATIONS
Not classified
GHS LABEL
No labeling applicable
EMERGENCY OVERVIEW
PHYSICAL APPEARANCE: Gray
IMMEDIATE CONCERNS: Solid tape packages in rolls with release paper.
POTENTIAL HEALTH EFFECTS
EYES: Contact may cause moderate eye irritation.
SKIN: Repeated or prolonged skin contact may result in allergic dermatitis. If product is hot, contact with the
skin will result in thermal burns.
INGESTION: Not likely route of entry.
INHALATION: Not likely route of entry.
CARCINOGENICITY: This product is not known to contain any components at concentrations above 0.1% which
are considered carcinogenic by OSHA, IARC or NTP.
3. COMPOSITION / INFORMATION ON INGREDIENTS
Chemical Name Wt.% CAS
Talc < 1514807-96-6 4. FIRST AID MEASURES EYES: Flush eye with tempered water for 15 minutes lifting upper and lower eye lids occasionally. If irritation persists, contact a physician. SKIN: Remove contaminated clothing. Immediately wash exp osed area with large amounts of water. If hot material adheres to the skin, do not attempt to peal off material. Cool the hot material with water and cover with a dry sterile dressing. Seek medical attention. INGESTION: Do not induce vomiting. Get medical attention immediately. Never give anything by mouth to an unconscious person. Page 1 of 5 SAFETY DATA SHEET Date Prepared : 09/13/2017 MSDS No : SM7191 Date Revised : 09/13/2017 Revision No : 1 TACKY TAPE SM7191 Vacuum Bag Sealant Tape INHALATION: Under normal conditions of use, inhalation of product is unlikely. If fumes are inhaled and become irritant, remove person from the area to fresh air. Seek immediate medical attention if exposure has occurred. NOTES TO PHYSICIAN: Treat symptomatically. 5. FIRE FIGHTING MEASURES FLAMMABLE CLASS: None GENERAL HAZARD: Non Hazardous EXTINGUISHING MEDIA: Use methods appropriate for the surrounding fire. Water spray, dry chemical, carbon dioxide, AFFF or alcohol resistant foams are all appropriate. EXPLOSION HAZARDS: Low hazard FIRE FIGHTING PROCEDURES: As in any fire, wear self-contained breathing apparatus with pressure-demand, full face piece SCBA (MSHA/NIOSH approved or equiva lent) and full protective gear. 6. ACCIDENTAL RELEASE MEASURES SMALL SPILL: This material is a solid tape product and release to the environment is highly unlikely. Containment is not necessary, this product will not flow. Use appropriate personal protective equipment (PPE) when handling product. Only employees properly trained should be part of any containment or spill response. LARGE SPILL: Refer to release measures under small spill, large spills are to be handled in the same manner. 7. HANDLING AND STORAGE HANDLING: Use good chemcial handling procedures and practices. No special handling precautions are required. STORAGE: Store at or under 80 degrees F. Do not stack cartons on end. Rotate stock. 8. EXPOSURE CONTROLS / PERSONAL PROTECTION EXPOSURE GUIDELINES OSHA HAZARDOUS COMPONENTS (29 CFR1910.1200) EXPOSURE LIMITS Chemical Name Type ppm mg/m 3 Talc OSHA PEL TWA 20 mpp 3.3 mg/m3 STEL NL [1] NL [1] ACGIH TLV TWA NL [1] 2 mg/m3 [1] STEL NL [1] NL [1] Footnotes: 1. NL = Not Listed ENGINEERING CONTROLS: Natural ventilation should be adequate under normal conditions. PERSONAL PROTECTIVE EQUIPMENT EYES AND FACE: Wear safety glasses with side shields. SKIN: Wear chemical resistant, impervious gloves. Page 2 of 5 SAFETY DATA SHEET Date Prepared : 09/13/2017 MSDS No : SM7191 Date Revised : 09/13/2017 Revision No : 1 TACKY TAPE SM7191 Vacuum Bag Sealant Tape RESPIRATORY: No respiratory protection required under normal conditions. WORK HYGIENIC PRACTICES: Use good hygiene practices when handling this material. Wash hands thoroughly after use. 9. PHYSICAL AND CHEMICAL PROPERTIES PHYSICAL STATE: Solid ODOR: None ODOR THRESHOLD: Not Determined COLOR: Gray PHYSICAL STATE COMMENTS: Tape material pH: 7.02 PERCENT VOLATILE: > 99.99% by weight
FLASHPOINT AND METHOD: Not Applicable
FLAMMABLE LIMITS: No data
AUTOIGNITION TEMPERATURE: Not Applicable
VAPOR PRESSURE: Not Determined
VAPOR DENSITY: Not Determined
BOILING POINT: Not Determined
FREEZING POINT: Not Determined
MELTING POINT: Not Determined
POUR POINT: Not Determined
SOLUBILITY IN WATER: Nonsoluble
PARTITION COEFFICIENT: N-OCTANOL/WATER: Not Determined
EVAPORATION RATE: Not Determined
DENSITY: 10.2 lbs/gal
PARTICLE SIZE: Not Determined
SPECIFIC GRAVITY: 1.22
VISCOSITY: Not Determined
MOLECULAR WEIGHT: Not Determined
(VOC): 2.4 gr/L EPA Method 24 VOC
OXIDIZING PROPERTIES: Not Determined
10. STABILITY AND REACTIVITY
REACTIVITY: Yes
HAZARDOUS POLYMERIZATION: Product will not undergo polymerization.
STABILITY: Stable.
CONDITIONS TO AVOID: No conditions known
POSSIBILITY OF HAZARDOUS REACTIONS: None
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon dioxide, carbon monoxide, hydrogen chloride and sulfides.
Page 3 of 5

SAFETY DATA SHEET
Date Prepared : 09/13/2017
MSDS No : SM7191
Date Revised : 09/13/2017
Revision No : 1
TACKY TAPE SM7191 Vacuum Bag Sealant Tape
INCOMPATIBLE MATERIALS: Liquid chlorine, potassium permanganate, fuming nitric acid, fluorine and other
strong oxidizing and base agents.
11. TOXICOLOGICAL INFORMATION
ACUTE TOXICITY
Chemical Name ORAL LD50 (rat) DERMAL LD 50 (rabbit) INHALATION LC 50 (rat)
Talc No data No data No data
NOTES: No known acute effects.
12. ECOLOGICAL INFORMATION
ENVIRONMENTAL DATA: No environmental information was found for this product.
ECOTOXICOLOGICAL INFORMATION: No ecotoxicity data was found for this product.
BIOACCUMULATION/ACCUMULATION: Contains components with the potential to bio-accumulate.
13. DISPOSAL CONSIDERATIONS
DISPOSAL METHOD: Consult with the US EPA Guidelines listed in 40 CFR Part 261.3 for the classifications of
hazardous waste prior to disposal. Consult with your state and local hazardous waste requirements or guidelines
to ensure compliance. Arrange disposal in accordance with EPA, state and local requirements.
14. TRANSPORT INFORMATION
DOT (DEPARTMENT OF TRANSPORTATION)
PROPER SHIPPING NAME: Not Regulated for Transport
PRIMARY HAZARD CLASS/DIVISION: Not Regulated
UN/NA NUMBER: NA
PACKING GROUP: NA
15. REGULATORY INFORMATION
UNITED STATES
SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZ ATION ACT)
FIRE: No PRESSURE GENERATING: No REACTIVITY: No ACUTE: No CHRONIC: No
TSCA (TOXIC SUBSTANCE CONTROL ACT)
Chemical Name CAS
Talc 14807-96-6
16. OTHER INFORMATION
Date Revised: 09/13/2017
INFORMATION CONTACT: (972) 438-9111
REVISION SUMMARY: This MSDS replaces the 11/12/2014 MSDS. Revised: Section 1: Date Issued.
Page 4 of 5

SAFETY DATA SHEET
Date Prepared : 09/13/2017
MSDS No : SM7191
Date Revised : 09/13/2017
Revision No : 1
TACKY TAPE SM7191 Vacuum Bag Sealant Tape
HMIS RATING
HEALTH * 0
FLAMMABILITY 1
PHYSICAL HAZARD 0
PERSONAL PROTECTION B
NFPA CODES

1
0 0

GENERAL STATEMENTS: Keep out of reach of children
For professional or industrial use only
MANUFACTURER DISCLAIMER: This document may be used to comply with OSHA’s Ha zardous Communication
Standard, 29 CFR 1910.1200.
To the best of our knowledge, the information contained in this SDS is accurate. It is intended to assist the user
in his/her evaluation of the product’s hazards and safety precautions to be taken in its use. The data in this SDS
relate only to the specific material designated herein. We do not assume liability for the use of, or reliance on this
information, nor do we guarantee its accuracy or completeness.
This information is furnished without warranty, expressed or implied, except that it is accurate to the best
knowledge of ITW Polymers Sealants North America. The data on this sheet relates only to the specific material
designated herein. ITW Polymers Sealants North America assumes no legal responsibility for use or reliance upon
these data.
Page 5 of 5

08RBG50002A_SDS.pdf

by | Sep 27, 2025

SAFETY INFORMATION SHEET
Voluntary product information following the Safety Data Sheet format
Bagging Films
Material number 1025
Revision date: 1/9/2019
Version: 5
Language: en-US
Date of first version:10/21/2014
Page: 1 of 7
1. Product and company identification
Product identifier
Trade name: Bagging Films
NBF125C, Big Blue L-100, Securlon V-45, Securlon L-500Y, Securlon L-1000,
Securlon L-2000, Stretchlon 200, Stretchlon 700, Stretchlon 800, Stretchlon
850, Stretchlon HT-350, Ipplon KM1300, Ipplon DP1000, Ipplon DPT1000,
Ipplon WN1500, Wrightlon 600V, Wrightlon 5400, Wrightlon 6400, Wrightlon
7400, Wrightlon 8400, Dahlar Release Bag 125, Dahlar Release Bag 375R,
Dahlar Release Bag 460, Dahlar Release Bag 500, Econolon, Airdraw 2, Thermalimide
Relevant identified uses of the substance or mixture and uses advised against
General use: Article: Vacuum bagging film
Details of the supplier of the safety data sheet
Company name:
Airtech International, Inc.
5700 Skylab Road
Huntington Beach, CA 92647
E-mail: airtech@airtechintl.com
Website: www.airtechonline.com
Telephone: +1 714.899.8100
Dept. responsible for information:
Telephone: +1 714.899.8100
E-mail: airtech@airtechintl.com
Airtech Europe Sarl
Zone industrielle Haneboesch
L 4562 Differdange
Luxembourg
Website: www.airtech.lu
Telephone: +352 582.282
Dept. responsible for information:
Telephone: +352 582.282
E-mail: sales@airtech.lu
Tygavac Advanced Materials Ltd.
The Causeway
Broadway Business Park
Chadderton, Oldham
OL9 9XD United Kingdom
Website: www.tygavac.co.uk
Telephone: +44 161.947.1610
Dept. responsible for information:
Telephone: +44 161.947.1610
E-mail: sales@tygavac.co.uk
Airtech Asia Ltd.
No. 161 of Anyuan Rd
Chagugang County
Wuqing District
301721, Tianjin, P.R. China
Website: www.airtech.asia
Telephone: +86 22 8862 9800
Telefax:: +86 22 8862 9900
Dept. responsible for information:
Telephone: +86 22 8862 9800
E-mail: airtech.asia@airtechasia.com.cn
Emergency phone number
CHEMTREC EMERGENCY PHONE:
Within USA/Canada: 1-(800)424-9300
International: +1 703-741-5970
2. Hazards identification
Emergency overview
Appearance: Form: solid
Color: varying
Odor: odorless
Classification: Article not subject to hazard labelling or classification.
Regulatory status
This material is not considered hazardous by the U.S. OSHA Hazard Communication
Standard (29 CFR 1910.1200) and SIMDUT in Canada.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT

SAFETY INFORMATION SHEET
Voluntary product information following the Safety Data Sheet format
Bagging Films
Material number 1025
Revision date: 1/9/2019
Version: 5
Language: en-US
Date of first version:10/21/2014
Page: 2 of 7
Hazards not otherwise classified
Toxic fumes may be emitted at elevated temperatures. Do not breathe vapor. Processing,
e.g. by cutting, sawing or grinding, can produce particles and dust. Avoid inhalation of
dusts, as even inert dusts may functionally affect respiratory organs.
see section 11: Toxicological information
3. Composition / Information on ingredients
Chemical characterization:
Thermoplastic films
4. First aid measures
In case of inhalation:In case of inhalation of decomposition products, affected person should be moved into
fresh air and kept still. If the casualty has difficulty breathing, call a doctor immediately.
Following skin contact:After contact with molten product, cool skin area rapidly with cold water. Do not peel
solidified product off the skin. Seek medical attention.
After eye contact: In the event of irritation from processing vapors: Immediately flush eyes with plenty of
flowing water for 10 to 15 minutes holding eyelids apart. In case of troubles or persistent
symptoms, consult an opthalmologist.
After swallowing: Not a probable route of exposure.
In the case of the formation of dust: Rinse mouth. Seek medical treatment in case of
troubles.
Most important symptoms/effects, acute and delayed
In case of inhalation:
Inhalation of dust may cause irritation of the respiratory system. Overheating released
mist or vapors can irritate the respiratory tracts.
Other symptoms: Cough, respiratory complaints, dizziness, nausea, vomiting.
After contact with skin: The melted product can cause severe burns.
After eye contact:
Process vapors can irritate the eyes. Dust contact with the eyes can lead to mechanical
irritation.
Information to physician
Treat symptomatically.
5. Fire fighting measures
Flash point/flash point range:
No data available
Auto-ignition temperature:
No data available
Suitable extinguishing media:
Water spray jet, dry chemical powder, foam, carbon dioxide
Extinguishing media which must not be used for safety reasons:
Full water jet.
Specific hazards arising from the chemical
This material is combustible, but will not ignite readily. Toxic fumes may be emitted at
elevated temperatures.
In case of fire may be liberated: Caprolactam, nitrogen oxides (NOx), amines, carbon
monoxide and carbon dioxide, hydrogen cyanide, isocyanates, isocyanic acid.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT

SAFETY INFORMATION SHEET
Voluntary product information following the Safety Data Sheet format
Bagging Films
Material number 1025
Revision date: 1/9/2019
Version: 5
Language: en-US
Date of first version:10/21/2014
Page: 3 of 7
Protective equipment and precautions for firefighters:
Wear a self-contained breathing apparatus and chemical protective clothing.
Additional information:Seal off endangered area. Cool endangered containers with water spray and, if possible,
remove from danger zone. Use a water fog to control vapors. Do not breathe fumes. Do
not allow fire water to penetrate into surface or ground water.
6. Accidental release measures
Personal precautions:Handle in accordance with good industrial hygiene and safety practice.
At processing: Avoid the formation of aerosol/vapors. Avoid generation of dust. Avoid
inhalation and contact with skin and eyes. Wear appropriate protective equipment. Keep
unprotected people away. Ensure adequate ventilation, especially in confined areas.
Environmental precautions:
Do not allow to penetrate into soil, waterbodies or drains.
Methods for clean-up:Take up mechanically, placing in appropriate containers for disposal. Dispose of waste
according to applicable legislation.
7. Handling and storage
Handling
Advices on safe handling:Handle in accordance with good industrial hygiene and safety practice.
At processing: Provide adequate ventilation, and local exhaust as needed. Avoid the
formation of aerosol/vapors. Avoid generation of dust. Avoid inhalation and contact with
skin and eyes. Wear appropriate protective equipment. Keep unprotected people away.
When using do not eat, drink or smoke.
Precautions against fire and explosion:
Take standard precautions to prevent fire.
Storage
Requirements for storerooms and containers:
Keep in a cool place. Keep container dry. Protect from direct sunlight. Keep away from
incompatible materials. Store at room temperature.
Hints on joint storage:Incompatible materials: Strong bases, strong acids, strong oxidizing agents.
Keep away from food and drinks.
8. Exposure controls / personal protection
Exposure guidelines
Occupational exposure limit values:
Type Limit value
USA: ACGIH: TWA 10 mg/m (Dust limit value, inhalable fraction)
USA: ACGIH: TWA 3 mg/m (Dust limit value, respirable fraction)
USA: OSHA: TWA 15 mg/m (Dust limit value, inhalable fraction)
USA: OSHA: TWA 5 mg/m (Dust limit value, respirable fraction)
Engineering controls
Provide good ventilation and/or an exhaust system in the work area.
In case of development of vapors or dust (at processing): Use local exhaust.
See also information in chapter 7, section storage.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT

SAFETY INFORMATION SHEET
Voluntary product information following the Safety Data Sheet format
Bagging Films
Material number 1025
Revision date: 1/9/2019
Version: 5
Language: en-US
Date of first version:10/21/2014
Page: 4 of 7
Personal protection equipment (PPE)
Eye/face protectionAt processing (recommended): Safety glasses in accordance with OSHA 29 CFR:
1910.133 or ANSI Z87.1-2010.
Skin protection At processing (recommended): Wear suitable protective clothing.
Recommendation:
Protective gloves according to OSHA Standard – 29 CFR: 1910.138.
Glove material: nitrile rubber (0.11 mm)
Breakthrough time: 480 min.
Observe glove manufacturer’s instructions concerning penetrability and breakthrough time.
Respiratory protection:Respiratory protection is not necessary if room is well ventilated.
At processing:
When vapors form, use respiratory protection. The filter class must be suitable for the
maximum contaminant concentration (gas/vapour/aerosol/particulates) that may arise
when handling the product. If the concentration is exceeded, self-contained breathing
apparatus must be used.
General hygiene considerations:
Handle in accordance with good industrial hygiene and safety practice. Wash hands
before breaks and after work. When using do not eat, drink or smoke.
At processing:
Avoid contact with skin, eyes, and clothing. Do not breathe vapors. Do not breathe dust.
9. Physical and chemical properties
Information on basic physical and chemical properties
Appearance: Form: solid
Color: varying
Odor: odorless
Odor threshold: No data available
pH value: No data available
Melting point/freezing point: No data available
Initial boiling point and boiling range:No data available
Flash point/flash point range: No data available
Evaporation rate: No data available
Flammability: This material is combustible, but will not ignite readily.
Explosion limits: No data available
Vapor pressure: No data available
Vapor density: No data available
Density: No data available
Water solubility: at 68 F: insoluble
Partition coefficient: n-octanol/water:No data available
Auto-ignition temperature: No data available
Thermal decomposition: No data available
Additional information: No data available
10. Stability and reactivity
Reactivity: Refer to section: Possibility of hazardous reactions.
Chemical stability:Stable under recommended storage conditions.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT

SAFETY INFORMATION SHEET
Voluntary product information following the Safety Data Sheet format
Bagging Films
Material number 1025
Revision date: 1/9/2019
Version: 5
Language: en-US
Date of first version:10/21/2014
Page: 5 of 7
Possibility of hazardous reactions
No dangerous reactions with proper and specified storage and handling
Conditions to avoid:Keep away from heat. Protect from direct sunlight. Avoid generation of dust. Avoid the
formation of aerosol/vapors.
Incompatible materials:Strong bases, strong acids, strong oxidizing agents.
Hazardous decomposition products:
Caprolactam, nitrogen oxides (NOx), amines, carbon monoxide and carbon dioxide,
hydrogen cyanide, isocyanates, isocyanic acid.
Thermal decomposition:No data available
11. Toxicological information
Toxicological tests
Toxicological effects:The statements are derived from the properties of the single components. No toxicological
data is available for the product as such.
Acute toxicity (oral): Lack of data.
Acute toxicity (dermal): Lack of data.
Acute toxicity (inhalative): Lack of data.
Skin corrosion/irritation: Lack of data.
Serious eye damage/irritation: Lack of data.
Sensitisation to the respiratory tract: Lack of data.
Skin sensitisation: Lack of data.
Germ cell mutagenicity/Genotoxicity: Lack of data.
Carcinogenicity: Lack of data.
Reproductive toxicity: Lack of data.
Effects on or via lactation: Lack of data.
Specific target organ toxicity (single exposure): Lack of data.
Specific target organ toxicity (repeated exposure): Lack of data.
Aspiration hazard: Lack of data.
Other information: Toxic fumes may be emitted at elevated temperatures. Processing, e.g. by cutting,
sawing or grinding, can produce particles and dust. Dust may irritate airways and cause
bronchitis symptoms.
Information about Caprolactam: Harmful if swallowed. Harmful if inhaled. Causes skin
irritation. Causes serious eye irritation. May cause respiratory irritation.
Symptoms
In case of inhalation:
Inhalation of dust may cause irritation of the respiratory system. Overheating released
mist or vapors can irritate the respiratory tracts.
Other symptoms: Cough, respiratory complaints, dizziness, nausea, vomiting.
After contact with skin: The melted product can cause severe burns.
After eye contact:
Process vapors can irritate the eyes. Dust contact with the eyes can lead to mechanical
irritation.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT

SAFETY INFORMATION SHEET
Voluntary product information following the Safety Data Sheet format
Bagging Films
Material number 1025
Revision date: 1/9/2019
Version: 5
Language: en-US
Date of first version:10/21/2014
Page: 6 of 7
12. Ecological information
Ecotoxicity
Effects in sewage plants:The insoluble part can be precipitated mechanically in suitable sewage treatment plants.
Further details: No data available
Mobility in soil
No data available
Persistence and degradability
Further details: Product is not biodegradable.
Additional ecological information
General information:Do not allow to penetrate into soil, waterbodies or drains.
13. Disposal considerations
Product
Recommendation: Dispose of waste according to applicable legislation. Recycling or special waste
incineration.
Contaminated packaging
Recommendation: Dispose of waste according to applicable legislation. Non-contaminated packages may be
recycled.
14. Transport information
USA: Department of Transportation (DOT)
Proper shipping name: Not restricted
Sea transport (IMDG)
Proper shipping name: Not restricted
Marine pollutant: no
Air transport (IATA)
Proper shipping name: Not restricted
Further information
No dangerous good in sense of these transport regulations.
15. Regulatory information
National regulations – U.S. Federal Regulations
This product is an article as defined by TSCA regulations, and is exempt from TSCA
inventory listing requirements.
National regulations – Great Britain
Hazchem-Code: –
printed by Airtech Advanced Materials Group with Qualisys SUMDAT

SAFETY INFORMATION SHEET
Voluntary product information following the Safety Data Sheet format
Bagging Films
Material number 1025
Revision date: 1/9/2019
Version: 5
Language: en-US
Date of first version:10/21/2014
Page: 7 of 7
16. Other information
Hazard rating systems:
1
10
NFPA Hazard Rating:
Health: 1 (Slight)
Fire: 1 (Slight)
Reactivity: 0 (Minimal)
HEALTH 1
FLAMMABILITY 1
PHYSICAL HAZARD 0
X
HMIS Version III Rating:
Health: 1 (Slight)
Flammability: 1 (Slight)
Physical Hazard: 0 (Minimal)
Personal Protection: X = Consult your supervisor
Reason of change: Changes in section 1: product identifier
Department issuing data sheet
Contact person: see section 1: Dept. responsible for information
This data sheet cannot cover all possible situations which the user may experience during processing. Each
aspect of your operation should be examined to determine if, and which additional precautions may be
necessary. All health and safety information contained in this data sheet should be provided to your
employees and customers. It is your responsibility to develop appropriate workplace instructions and training
programs for employees.
As the conditions and methods of use are beyond our control, we do not assume any responsibility and
expressly disclaim any liability for any use of this product. The information supplied on this safety data sheet
complies with our current level of knowledge as well as with national and EU regulations. All statements or
suggestions are made without warranty, expressed or implied, regarding accuracy of information, the
hazards connected with the use of the product or the results to be obtained from the use thereof.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT