15752060H_SDS.pdf
Revision date: 5/1/2015 Revision: 0
SAFETY DATA SHEET
HexForce F3 and F16 Finish
1. Identification
Product identifier
Product name HexForce F3 and F16 Finish
Product number 20871US-2
Synonyms; trade names Applicable to: E Glass or S Glass with a Chromium (CR3+) Methacrylate Finish applied
Details of the supplier of the safety data sheet
Supplier Hexcel Reinforcements
1913 N. King Street
Seguin
TX 78155
USA
Tel: ++ 830 379 1580
Fax: ++ 830 379 9544
Contact Person 11711 Dublin Blvd, Dublin, California, USA. ++925 551 4900
Emergency telephone number
Emergency telephone To be used only for advice on chemical emergencies, spillages, fires or First Aid:
For emergencies in US/Canada: CHEMTREC 800 424 9300
For emergencies in rest of the world: CARECHEM24 – +44 (0) 1235 239 670
2. Hazard(s) identification
Classification of the substance or mixture
OSHA Regulatory Status This Product is Not Hazardous under the OSHA Hazard Communication Standard.
Physical hazards Combustible Dust – USH01
Health hazards Not Classified
Environmental hazards Not Classified
Label elements
Signal word Warning
Hazard statements USH01 May form combustible dust concentrations in air
Other hazards
Warning! May cause temporary mechanical irritation of the eyes, skin or upper respiratory tract. The American Conference of
Governmental Industrial Hygienists (ACGIH) lists under synthetic vitreous fiber; continous filament glass fibers: 1 f/cc
(respirable) and 5 mg/m3 (inhalable). Warning! Dust generated from machining, grinding or sanding the product may be
combustible and could result in fire and/or explosion should the necessary dust concentration in air and ignition source be
present.
Hazards not otherwise
classified (HNOC)
Fine dust clouds may form explosive mixtures with air.
1/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
3. Composition/information on ingredients
Mixtures
Composition comments Continuous filament glass fiber (type E, R, D, S2) of silicon, aluminum, calcium, boron and
magnesium oxides in a vitreous amorphous state. Filament diameter r>3um CAS 65997-17-
3: >99% w/w
4. First-aid measures
Description of first aid measures
Inhalation With any sign of respiratory distress, affected persons should be taken into fresh air and made
to rest while medical attention is sought.
Ingestion If fiber from the product is ingested, immediately rinse mouth repeatedly with water. If
swallowing has occurred, do not induce vomiting. If requested, give affected person sips of
water. Seek medical attention.
Skin Contact In case of contact with the product or the cured product dust or particulates, immediately wash
skin with mild soap and water. Use a washcloth to help remove fibers. To avoid further
irritation, do not scratch irritated areas. Rubbing or scratching may force the fibers into the
skin. Get medical attention immediately if the irritation persists.
Eye contact contamination by fiber should be removed by flushing with water for at least 15 minutes. Seek
medical attention if irritation persists.
Most important symptoms and effects, both acute and delayed
General information Filaments are mechanical irritants and may induce temporary mouth, nose and throat
irritation. Skin or eye contact may cause itching and temporary irritation. Ingestion may cause
temporary mechanical irritation of the digestive tract. Pre-existing conditions such as
respiratory or skin disorders may be aggravated by exposure to the product or dust/particulate
generated from machining/grinding of the cured product.
Indication of immediate medical attention and special treatment needed
Notes for the doctor No specific recommendations. If in doubt, get medical attention promptly.
5.Fire-fighting measures
Extinguishing media
Suitable extinguishing mediaExtinguish with foam, carbon dioxide, dry powder or water fog.
Unsuitable extinguishing
media
Do not use water jet as an extinguisher, as this will spread the fire.
Special hazards arising from the substance or mixture
Specific hazards No unusual fire or explosion hazards noted.
Hazardous combustion
products
In an emergency situation leading to elevated temperature, there may be release of toxic
gases and vapours. The products of combustion and decomposition will depend on other
materials present in the fire and the actual conditions of the fire.
Advice for firefighters
Special protective equipment
for firefighters
Wear positive-pressure self-contained breathing apparatus (SCBA) and appropriate protective
clothing.
6. Accidental release measures
Personal precautions, protective equipment and emergency procedures
Personal precautions Avoid contact with skin, eyes or clothing.
2/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
Environmental precautions
Environmental precautionsDue to the physical nature of this product, environmental release to drains and water courses
is not possible.
3/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
Methods and material for containment and cleaning up
Methods for cleaning up Clean up material and put into a suitable container and dispose of properly (See Section 13).
Reference to other sectionsFor personal protection, see Section 8. Collect and dispose of spillage as indicated in Section
13.
7. Handling and storage
Precautions for safe handling
Usage precautions Storage: Keep container tightly closed and dry.
Conditions for safe storage, including any incompatibilities
Storage precautions Store in tightly-closed, original container. Keep container dry.
Specific end uses(s)
Specific end use(s) As this product is an article, this section is not applicable.
8. Exposure Controls/personal protection
Control parameters
Occupational exposure limits
Long-term exposure limit (8-hour TWA): 1 f/cc 5 mg/m3 continuous filament glass fibers
Exposure controls
Protective equipment
Appropriate engineering
controls
Provide adequate ventilation.
Eye/face protection Eyewear complying with an approved standard should be worn if a risk assessment indicates
eye contact is possible.
Hand protection It is recommended that gloves are made of the following material: Polyvinyl chloride (PVC).
Rubber (natural, latex).
Other skin and body
protection
Wear appropriate clothing to prevent any possibility of skin contact.
Hygiene measures Wash hands at the end of each work shift and before eating, smoking and using the toilet.
Respiratory protection Wear a suitable dust mask.
4/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
9. Physical and Chemical Properties
Information on basic physical and chemical properties
Appearance White fibers woven into fabrics of varying weight, width and thickness, depending on the style,
with a finish applied.
Color White.
Odor No characteristic odor.
Odor threshold Not relevant due to the physical form of this product.
pH Not relevant due to the physical form of this product.
Melting point 700C / 1292F C
Initial boiling point and rangeNot relevant due to the physical form of this product.
Flash point Not relevant due to the physical form of this product.
Evaporation rate Not relevant due to the physical form of this product.
Evaporation factor Not relevant due to the physical form of this product.
Upper/lower flammability or
explosive limits
Not relevant due to the physical form of this product.
Vapour pressure Not relevant due to the physical form of this product.
Vapour density Not relevant due to the physical form of this product.
Relative density Not relevant due to the physical form of this product.
Solubility(ies) Not relevant due to the physical form of this product.
Auto-ignition temperatureNot relevant due to the physical form of this product.
Viscosity Not relevant due to the physical form of this product.
Explosive properties The mixture does not meet the criteria for explosive in accordance with GHS.
Explosive under the influence
of a flame
The mixture does not meet the criteria for explosive in accordance with GHS.
Oxidising properties Does not meet the criteria for classification as oxidizing.
Comments The indicated values do not necessarily correspond to the product specification. Please refer
to the technical data sheet for specification data.
5/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
10. Stability and reactivity
Stability Stable at normal ambient temperatures and when used as recommended.
Possibility of hazardous
reactions
Not relevant.
Conditions to avoid Avoid heat, flames and other sources of ignition.
Materials to avoid No specific material or group of materials is likely to react with the product to produce a
hazardous situation.
Hazardous decomposition
products
Does not decompose when used and stored as recommended. In an emergency situation
leading to elevated temperature, there may be release of toxic gases and vapors. The
products of combustion and decompostion will depend on other materials present in the fire
and the actual conditions of the fire.
11. Toxicological information
Information on toxicological effects
Toxicological effects Continuous filament fiber is listed by the International Agency for Research on Cancer (IARC)
as a group 3 (not classifiable as a human carcinogen).
Carcinogenicity
IARC carcinogenicity IARC Group 3 Not classifiable as to its carcinogenicity to humans.
Inhalation May cause respiratory system irritation.
Ingestion None expected under normal conditions of use. Ingestion is not an expected route of industrial
exposure.
Skin Contact Contact may cause mechanical irritation, skin redness, itching and drying of the skin.
Prolonged or repeated contact may cause allergic skin reaction, dermatitis and possible
sensitization.
Eye contact May cause mechanical irritation.
Medical considerations Preexisting eye, skin or respiratory disorders may be aggravated by exposure to this product.
12. Ecological Information
Ecotoxicity No ecological data has been determined on the total product.
Toxicity
Toxicity Not regarded as dangerous for the environment.
Persistance and degradability
Persistence and degradabilityNot relevant due to the physical form of this product.
Bioaccumulative potential
Bio-Accumulative PotentialNot relevant due to the physical form of this product.
Mobility in soil
Mobility Not relevant due to the physical form of this product.
6/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
13. Disposal considerations
Waste treatment methods
General information Materials for disposal should be placed in appropriate sealed containers to avoid potential
human and environmental exposure. It is the responsibility of the generator to comply with all
federal, state, provincial and local laws and regulations. We recommend that you contact an
appropriate waste disposal contractor and environmental agency for relevant laws and
regulations. Under the U.S., Resource Conservation and Recovery Act (RCRA), it is the
responsibility of the user of the product to determine at the time of disposal, whether the
product meets relevant waste classification and to assure proper disposal.
Disposal methods Dispose of waste to licensed waste disposal site in accordance with the requirements of the
local Waste Disposal Authority.
14. Transport information
General Not regulated.
UN Number
This product is not dangerous to transport.
UN proper shipping name
This product is not dangerous to transport.
Transport hazard class(es)
This product is not dangerous to transport.
Packing group
This product is not dangerous to transport.
Environmental hazards
Environmentally Hazardous Substance
No.
Special precautions for user
This product is not dangerous to transport.
15. Regulatory information
US Federal Regulations
SARA Section 302 Extremely Hazardous Substances Tier II Threshold Planning Quantities
Not listed.
CERCLA/Superfund, Hazardous Substances/Reportable Quantities (EPA)
Not listed.
SARA Extremely Hazardous Substances EPCRA Reportable Quantities
Not listed.
SARA 313 Emission Reporting
Not listed
7/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
RCRA RCRA Information: Currently, the product is not listed in the federal hazardous waste
regulation 40 CFR, Part 261.33, paragraphs (E) or (F), ie. chemical products that are
considered hazardous if they become waste. State or local hazardous waste regulations may
also apply if they are different from the federal regulation. It is the responsibility of the user of
the product to determine at the time of disposal, whether the product meets relevant waste
classification and to assure proper disposal.
SARA (311/312) Hazard Categories
None.
US State Regulations
California Proposition 65 Carcinogens and Reproductive Toxins
This product contains no listed substances known to the State of California to cause cancer, birth
defects or other reproductive harm, at levels which would require a warning under the statute.
Inventories
US – TSCA
This product is an article as defined by TSCA and is not required to be listed in the TSCA inventory.
US – TSCA 12(b) Export Notification
Not listed.
16. Other information
Abbreviations and acronyms
used in the safety data sheet
ACGIH American Conference of Industrial Hygienists ATE Acute Toxicity Estimate CAS#
Chemical Abstracts Service Number CERCLA Comprehensive Environmental Response,
Compensation, and Liability Act DOT Department of Transportation EmS Emergency
Response Procedures for Ships Carrying Dangerous Goods EPA Environmental Protection
Agency GHS Global Harmonized System HMIS Hazardous Materials Identification System,
IATA International Air Transport Association ICAO International Civil Aviation Organization
IMDG International Maritime Dangerous Goods Kow Octanol-water partition coefficient LC50
Lethal concentration to 50% of a test population LD50 Lethal dose to 50% of a test population
n.o.s. Not otherwise specified OSHA Occupational Safety and Health Administration PBT
Persistent, Bioaccumulative and Toxic substance PNEC Predicted No Effect Concentration
PPE Personal Protection Equipment RCRA Resource Conservation and Recovery Act SADT
Self-accelerating decomposition temperature SARA Superfund Admendments and
Reauthorization Act STOT Specific Target Organ Toxicity (STOT) RE Repeated Exposure
(STOT) SE Single Exposure TSCA Toxic Substance Control Act UN United Nations VOC
Volatile Organic Compound WHMIS Workplace Hazardous Materials Information System
Issued by U.S.A. Product Stewardship department
Revision date 5/1/2015
Revision 0
Hazard statements in fullUSH01 May form combustible dust concentrations in air
ACA HMIS Health rating. Slight hazard. (1)
ACA HMIS Physical hazard
rating.
Normally stable. (0)
ACA HMIS Personal
protection rating.
F
ACA HMIS Flammability
rating.
Will not burn. (0)
8/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
Wherever such words or phrases as “hazardous,” “toxic,” “carcinogen,” etc. appear herein, they are used as a defined or
described under state employee right-to-know laws, Federal OSHA laws or the direct sources for these lawssuch as the
International Agency for Research on Cancer (IARC), the National Toxicology Program (NTP), etc. The use of such words or
phrases should not be taken to mean that we deem or imply any substance or exposure to be toxic, hazardous or otherwise
harmful. Any exposure can only be understood within the entire context of its occurrence, which includes such factors as the
substance’s characteristics as defined in the SDS, amount and duration of exposures, other chemicals present and
preexistingindividual differences in response to the exposure. The data provided in this SDS is based on the information
received from our raw material suppliers and other sources believed to be reliable. We are supplying you this data solely in
compliance with the Federal OSHA Hazard Communication Standard, 29 CFR 1910.1200 and the Federal and State laws as
described in Section 15: Regulatory Information. The information contained in this SDS is proprietary and confidential to
HexcelCorporation. This SDS and the information in it are not to be used for purposes other than compliance with the
Federal OSHA Hazard Communication Standard. If you have received this SDS from any other source than Hexcel
Corporation or its authorized agent, the information contained in it may have been modified from the original document and it
may not be the most current revision. Liability, if any, for use of this product is limited to the terms contained in our sale terms
and conditions. We do not in any way warrant (expressed or implied, including any implied warranty for merchantability or
fitness for a particular purpose) the data contained or the product described in this SDS. Additionally, we do not warrant that
the product will not infringe any patent or other proprietary or property rights of others.
9/9
15753053_SDS.pdf
15752050_SDS.pdf
Revision date: 5/1/2015 Revision: 0
SAFETY DATA SHEET
HexForce F3 and F16 Finish
1. Identification
Product identifier
Product name HexForce F3 and F16 Finish
Product number 20871US-2
Synonyms; trade names Applicable to: E Glass or S Glass with a Chromium (CR3+) Methacrylate Finish applied
Details of the supplier of the safety data sheet
Supplier Hexcel Reinforcements
1913 N. King Street
Seguin
TX 78155
USA
Tel: ++ 830 379 1580
Fax: ++ 830 379 9544
Contact Person 11711 Dublin Blvd, Dublin, California, USA. ++925 551 4900
Emergency telephone number
Emergency telephone To be used only for advice on chemical emergencies, spillages, fires or First Aid:
For emergencies in US/Canada: CHEMTREC 800 424 9300
For emergencies in rest of the world: CARECHEM24 – +44 (0) 1235 239 670
2. Hazard(s) identification
Classification of the substance or mixture
OSHA Regulatory Status This Product is Not Hazardous under the OSHA Hazard Communication Standard.
Physical hazards Combustible Dust – USH01
Health hazards Not Classified
Environmental hazards Not Classified
Label elements
Signal word Warning
Hazard statements USH01 May form combustible dust concentrations in air
Other hazards
Warning! May cause temporary mechanical irritation of the eyes, skin or upper respiratory tract. The American Conference of
Governmental Industrial Hygienists (ACGIH) lists under synthetic vitreous fiber; continous filament glass fibers: 1 f/cc
(respirable) and 5 mg/m3 (inhalable). Warning! Dust generated from machining, grinding or sanding the product may be
combustible and could result in fire and/or explosion should the necessary dust concentration in air and ignition source be
present.
Hazards not otherwise
classified (HNOC)
Fine dust clouds may form explosive mixtures with air.
1/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
3. Composition/information on ingredients
Mixtures
Composition comments Continuous filament glass fiber (type E, R, D, S2) of silicon, aluminum, calcium, boron and
magnesium oxides in a vitreous amorphous state. Filament diameter r>3um CAS 65997-17-
3: >99% w/w
4. First-aid measures
Description of first aid measures
Inhalation With any sign of respiratory distress, affected persons should be taken into fresh air and made
to rest while medical attention is sought.
Ingestion If fiber from the product is ingested, immediately rinse mouth repeatedly with water. If
swallowing has occurred, do not induce vomiting. If requested, give affected person sips of
water. Seek medical attention.
Skin Contact In case of contact with the product or the cured product dust or particulates, immediately wash
skin with mild soap and water. Use a washcloth to help remove fibers. To avoid further
irritation, do not scratch irritated areas. Rubbing or scratching may force the fibers into the
skin. Get medical attention immediately if the irritation persists.
Eye contact contamination by fiber should be removed by flushing with water for at least 15 minutes. Seek
medical attention if irritation persists.
Most important symptoms and effects, both acute and delayed
General information Filaments are mechanical irritants and may induce temporary mouth, nose and throat
irritation. Skin or eye contact may cause itching and temporary irritation. Ingestion may cause
temporary mechanical irritation of the digestive tract. Pre-existing conditions such as
respiratory or skin disorders may be aggravated by exposure to the product or dust/particulate
generated from machining/grinding of the cured product.
Indication of immediate medical attention and special treatment needed
Notes for the doctor No specific recommendations. If in doubt, get medical attention promptly.
5.Fire-fighting measures
Extinguishing media
Suitable extinguishing mediaExtinguish with foam, carbon dioxide, dry powder or water fog.
Unsuitable extinguishing
media
Do not use water jet as an extinguisher, as this will spread the fire.
Special hazards arising from the substance or mixture
Specific hazards No unusual fire or explosion hazards noted.
Hazardous combustion
products
In an emergency situation leading to elevated temperature, there may be release of toxic
gases and vapours. The products of combustion and decomposition will depend on other
materials present in the fire and the actual conditions of the fire.
Advice for firefighters
Special protective equipment
for firefighters
Wear positive-pressure self-contained breathing apparatus (SCBA) and appropriate protective
clothing.
6. Accidental release measures
Personal precautions, protective equipment and emergency procedures
Personal precautions Avoid contact with skin, eyes or clothing.
2/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
Environmental precautions
Environmental precautionsDue to the physical nature of this product, environmental release to drains and water courses
is not possible.
3/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
Methods and material for containment and cleaning up
Methods for cleaning up Clean up material and put into a suitable container and dispose of properly (See Section 13).
Reference to other sectionsFor personal protection, see Section 8. Collect and dispose of spillage as indicated in Section
13.
7. Handling and storage
Precautions for safe handling
Usage precautions Storage: Keep container tightly closed and dry.
Conditions for safe storage, including any incompatibilities
Storage precautions Store in tightly-closed, original container. Keep container dry.
Specific end uses(s)
Specific end use(s) As this product is an article, this section is not applicable.
8. Exposure Controls/personal protection
Control parameters
Occupational exposure limits
Long-term exposure limit (8-hour TWA): 1 f/cc 5 mg/m3 continuous filament glass fibers
Exposure controls
Protective equipment
Appropriate engineering
controls
Provide adequate ventilation.
Eye/face protection Eyewear complying with an approved standard should be worn if a risk assessment indicates
eye contact is possible.
Hand protection It is recommended that gloves are made of the following material: Polyvinyl chloride (PVC).
Rubber (natural, latex).
Other skin and body
protection
Wear appropriate clothing to prevent any possibility of skin contact.
Hygiene measures Wash hands at the end of each work shift and before eating, smoking and using the toilet.
Respiratory protection Wear a suitable dust mask.
4/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
9. Physical and Chemical Properties
Information on basic physical and chemical properties
Appearance White fibers woven into fabrics of varying weight, width and thickness, depending on the style,
with a finish applied.
Color White.
Odor No characteristic odor.
Odor threshold Not relevant due to the physical form of this product.
pH Not relevant due to the physical form of this product.
Melting point 700C / 1292F C
Initial boiling point and rangeNot relevant due to the physical form of this product.
Flash point Not relevant due to the physical form of this product.
Evaporation rate Not relevant due to the physical form of this product.
Evaporation factor Not relevant due to the physical form of this product.
Upper/lower flammability or
explosive limits
Not relevant due to the physical form of this product.
Vapour pressure Not relevant due to the physical form of this product.
Vapour density Not relevant due to the physical form of this product.
Relative density Not relevant due to the physical form of this product.
Solubility(ies) Not relevant due to the physical form of this product.
Auto-ignition temperatureNot relevant due to the physical form of this product.
Viscosity Not relevant due to the physical form of this product.
Explosive properties The mixture does not meet the criteria for explosive in accordance with GHS.
Explosive under the influence
of a flame
The mixture does not meet the criteria for explosive in accordance with GHS.
Oxidising properties Does not meet the criteria for classification as oxidizing.
Comments The indicated values do not necessarily correspond to the product specification. Please refer
to the technical data sheet for specification data.
5/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
10. Stability and reactivity
Stability Stable at normal ambient temperatures and when used as recommended.
Possibility of hazardous
reactions
Not relevant.
Conditions to avoid Avoid heat, flames and other sources of ignition.
Materials to avoid No specific material or group of materials is likely to react with the product to produce a
hazardous situation.
Hazardous decomposition
products
Does not decompose when used and stored as recommended. In an emergency situation
leading to elevated temperature, there may be release of toxic gases and vapors. The
products of combustion and decompostion will depend on other materials present in the fire
and the actual conditions of the fire.
11. Toxicological information
Information on toxicological effects
Toxicological effects Continuous filament fiber is listed by the International Agency for Research on Cancer (IARC)
as a group 3 (not classifiable as a human carcinogen).
Carcinogenicity
IARC carcinogenicity IARC Group 3 Not classifiable as to its carcinogenicity to humans.
Inhalation May cause respiratory system irritation.
Ingestion None expected under normal conditions of use. Ingestion is not an expected route of industrial
exposure.
Skin Contact Contact may cause mechanical irritation, skin redness, itching and drying of the skin.
Prolonged or repeated contact may cause allergic skin reaction, dermatitis and possible
sensitization.
Eye contact May cause mechanical irritation.
Medical considerations Preexisting eye, skin or respiratory disorders may be aggravated by exposure to this product.
12. Ecological Information
Ecotoxicity No ecological data has been determined on the total product.
Toxicity
Toxicity Not regarded as dangerous for the environment.
Persistance and degradability
Persistence and degradabilityNot relevant due to the physical form of this product.
Bioaccumulative potential
Bio-Accumulative PotentialNot relevant due to the physical form of this product.
Mobility in soil
Mobility Not relevant due to the physical form of this product.
6/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
13. Disposal considerations
Waste treatment methods
General information Materials for disposal should be placed in appropriate sealed containers to avoid potential
human and environmental exposure. It is the responsibility of the generator to comply with all
federal, state, provincial and local laws and regulations. We recommend that you contact an
appropriate waste disposal contractor and environmental agency for relevant laws and
regulations. Under the U.S., Resource Conservation and Recovery Act (RCRA), it is the
responsibility of the user of the product to determine at the time of disposal, whether the
product meets relevant waste classification and to assure proper disposal.
Disposal methods Dispose of waste to licensed waste disposal site in accordance with the requirements of the
local Waste Disposal Authority.
14. Transport information
General Not regulated.
UN Number
This product is not dangerous to transport.
UN proper shipping name
This product is not dangerous to transport.
Transport hazard class(es)
This product is not dangerous to transport.
Packing group
This product is not dangerous to transport.
Environmental hazards
Environmentally Hazardous Substance
No.
Special precautions for user
This product is not dangerous to transport.
15. Regulatory information
US Federal Regulations
SARA Section 302 Extremely Hazardous Substances Tier II Threshold Planning Quantities
Not listed.
CERCLA/Superfund, Hazardous Substances/Reportable Quantities (EPA)
Not listed.
SARA Extremely Hazardous Substances EPCRA Reportable Quantities
Not listed.
SARA 313 Emission Reporting
Not listed
7/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
RCRA RCRA Information: Currently, the product is not listed in the federal hazardous waste
regulation 40 CFR, Part 261.33, paragraphs (E) or (F), ie. chemical products that are
considered hazardous if they become waste. State or local hazardous waste regulations may
also apply if they are different from the federal regulation. It is the responsibility of the user of
the product to determine at the time of disposal, whether the product meets relevant waste
classification and to assure proper disposal.
SARA (311/312) Hazard Categories
None.
US State Regulations
California Proposition 65 Carcinogens and Reproductive Toxins
This product contains no listed substances known to the State of California to cause cancer, birth
defects or other reproductive harm, at levels which would require a warning under the statute.
Inventories
US – TSCA
This product is an article as defined by TSCA and is not required to be listed in the TSCA inventory.
US – TSCA 12(b) Export Notification
Not listed.
16. Other information
Abbreviations and acronyms
used in the safety data sheet
ACGIH American Conference of Industrial Hygienists ATE Acute Toxicity Estimate CAS#
Chemical Abstracts Service Number CERCLA Comprehensive Environmental Response,
Compensation, and Liability Act DOT Department of Transportation EmS Emergency
Response Procedures for Ships Carrying Dangerous Goods EPA Environmental Protection
Agency GHS Global Harmonized System HMIS Hazardous Materials Identification System,
IATA International Air Transport Association ICAO International Civil Aviation Organization
IMDG International Maritime Dangerous Goods Kow Octanol-water partition coefficient LC50
Lethal concentration to 50% of a test population LD50 Lethal dose to 50% of a test population
n.o.s. Not otherwise specified OSHA Occupational Safety and Health Administration PBT
Persistent, Bioaccumulative and Toxic substance PNEC Predicted No Effect Concentration
PPE Personal Protection Equipment RCRA Resource Conservation and Recovery Act SADT
Self-accelerating decomposition temperature SARA Superfund Admendments and
Reauthorization Act STOT Specific Target Organ Toxicity (STOT) RE Repeated Exposure
(STOT) SE Single Exposure TSCA Toxic Substance Control Act UN United Nations VOC
Volatile Organic Compound WHMIS Workplace Hazardous Materials Information System
Issued by U.S.A. Product Stewardship department
Revision date 5/1/2015
Revision 0
Hazard statements in fullUSH01 May form combustible dust concentrations in air
ACA HMIS Health rating. Slight hazard. (1)
ACA HMIS Physical hazard
rating.
Normally stable. (0)
ACA HMIS Personal
protection rating.
F
ACA HMIS Flammability
rating.
Will not burn. (0)
8/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
Wherever such words or phrases as “hazardous,” “toxic,” “carcinogen,” etc. appear herein, they are used as a defined or
described under state employee right-to-know laws, Federal OSHA laws or the direct sources for these lawssuch as the
International Agency for Research on Cancer (IARC), the National Toxicology Program (NTP), etc. The use of such words or
phrases should not be taken to mean that we deem or imply any substance or exposure to be toxic, hazardous or otherwise
harmful. Any exposure can only be understood within the entire context of its occurrence, which includes such factors as the
substance’s characteristics as defined in the SDS, amount and duration of exposures, other chemicals present and
preexistingindividual differences in response to the exposure. The data provided in this SDS is based on the information
received from our raw material suppliers and other sources believed to be reliable. We are supplying you this data solely in
compliance with the Federal OSHA Hazard Communication Standard, 29 CFR 1910.1200 and the Federal and State laws as
described in Section 15: Regulatory Information. The information contained in this SDS is proprietary and confidential to
HexcelCorporation. This SDS and the information in it are not to be used for purposes other than compliance with the
Federal OSHA Hazard Communication Standard. If you have received this SDS from any other source than Hexcel
Corporation or its authorized agent, the information contained in it may have been modified from the original document and it
may not be the most current revision. Liability, if any, for use of this product is limited to the terms contained in our sale terms
and conditions. We do not in any way warrant (expressed or implied, including any implied warranty for merchantability or
fitness for a particular purpose) the data contained or the product described in this SDS. Additionally, we do not warrant that
the product will not infringe any patent or other proprietary or property rights of others.
9/9
15752038_SDS.pdf
Revision date: 5/1/2015 Revision: 0
SAFETY DATA SHEET
HexForce F3 and F16 Finish
1. Identification
Product identifier
Product name HexForce F3 and F16 Finish
Product number 20871US-2
Synonyms; trade names Applicable to: E Glass or S Glass with a Chromium (CR3+) Methacrylate Finish applied
Details of the supplier of the safety data sheet
Supplier Hexcel Reinforcements
1913 N. King Street
Seguin
TX 78155
USA
Tel: ++ 830 379 1580
Fax: ++ 830 379 9544
Contact Person 11711 Dublin Blvd, Dublin, California, USA. ++925 551 4900
Emergency telephone number
Emergency telephone To be used only for advice on chemical emergencies, spillages, fires or First Aid:
For emergencies in US/Canada: CHEMTREC 800 424 9300
For emergencies in rest of the world: CARECHEM24 – +44 (0) 1235 239 670
2. Hazard(s) identification
Classification of the substance or mixture
OSHA Regulatory Status This Product is Not Hazardous under the OSHA Hazard Communication Standard.
Physical hazards Combustible Dust – USH01
Health hazards Not Classified
Environmental hazards Not Classified
Label elements
Signal word Warning
Hazard statements USH01 May form combustible dust concentrations in air
Other hazards
Warning! May cause temporary mechanical irritation of the eyes, skin or upper respiratory tract. The American Conference of
Governmental Industrial Hygienists (ACGIH) lists under synthetic vitreous fiber; continous filament glass fibers: 1 f/cc
(respirable) and 5 mg/m3 (inhalable). Warning! Dust generated from machining, grinding or sanding the product may be
combustible and could result in fire and/or explosion should the necessary dust concentration in air and ignition source be
present.
Hazards not otherwise
classified (HNOC)
Fine dust clouds may form explosive mixtures with air.
1/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
3. Composition/information on ingredients
Mixtures
Composition comments Continuous filament glass fiber (type E, R, D, S2) of silicon, aluminum, calcium, boron and
magnesium oxides in a vitreous amorphous state. Filament diameter r>3um CAS 65997-17-
3: >99% w/w
4. First-aid measures
Description of first aid measures
Inhalation With any sign of respiratory distress, affected persons should be taken into fresh air and made
to rest while medical attention is sought.
Ingestion If fiber from the product is ingested, immediately rinse mouth repeatedly with water. If
swallowing has occurred, do not induce vomiting. If requested, give affected person sips of
water. Seek medical attention.
Skin Contact In case of contact with the product or the cured product dust or particulates, immediately wash
skin with mild soap and water. Use a washcloth to help remove fibers. To avoid further
irritation, do not scratch irritated areas. Rubbing or scratching may force the fibers into the
skin. Get medical attention immediately if the irritation persists.
Eye contact contamination by fiber should be removed by flushing with water for at least 15 minutes. Seek
medical attention if irritation persists.
Most important symptoms and effects, both acute and delayed
General information Filaments are mechanical irritants and may induce temporary mouth, nose and throat
irritation. Skin or eye contact may cause itching and temporary irritation. Ingestion may cause
temporary mechanical irritation of the digestive tract. Pre-existing conditions such as
respiratory or skin disorders may be aggravated by exposure to the product or dust/particulate
generated from machining/grinding of the cured product.
Indication of immediate medical attention and special treatment needed
Notes for the doctor No specific recommendations. If in doubt, get medical attention promptly.
5.Fire-fighting measures
Extinguishing media
Suitable extinguishing mediaExtinguish with foam, carbon dioxide, dry powder or water fog.
Unsuitable extinguishing
media
Do not use water jet as an extinguisher, as this will spread the fire.
Special hazards arising from the substance or mixture
Specific hazards No unusual fire or explosion hazards noted.
Hazardous combustion
products
In an emergency situation leading to elevated temperature, there may be release of toxic
gases and vapours. The products of combustion and decomposition will depend on other
materials present in the fire and the actual conditions of the fire.
Advice for firefighters
Special protective equipment
for firefighters
Wear positive-pressure self-contained breathing apparatus (SCBA) and appropriate protective
clothing.
6. Accidental release measures
Personal precautions, protective equipment and emergency procedures
Personal precautions Avoid contact with skin, eyes or clothing.
2/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
Environmental precautions
Environmental precautionsDue to the physical nature of this product, environmental release to drains and water courses
is not possible.
3/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
Methods and material for containment and cleaning up
Methods for cleaning up Clean up material and put into a suitable container and dispose of properly (See Section 13).
Reference to other sectionsFor personal protection, see Section 8. Collect and dispose of spillage as indicated in Section
13.
7. Handling and storage
Precautions for safe handling
Usage precautions Storage: Keep container tightly closed and dry.
Conditions for safe storage, including any incompatibilities
Storage precautions Store in tightly-closed, original container. Keep container dry.
Specific end uses(s)
Specific end use(s) As this product is an article, this section is not applicable.
8. Exposure Controls/personal protection
Control parameters
Occupational exposure limits
Long-term exposure limit (8-hour TWA): 1 f/cc 5 mg/m3 continuous filament glass fibers
Exposure controls
Protective equipment
Appropriate engineering
controls
Provide adequate ventilation.
Eye/face protection Eyewear complying with an approved standard should be worn if a risk assessment indicates
eye contact is possible.
Hand protection It is recommended that gloves are made of the following material: Polyvinyl chloride (PVC).
Rubber (natural, latex).
Other skin and body
protection
Wear appropriate clothing to prevent any possibility of skin contact.
Hygiene measures Wash hands at the end of each work shift and before eating, smoking and using the toilet.
Respiratory protection Wear a suitable dust mask.
4/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
9. Physical and Chemical Properties
Information on basic physical and chemical properties
Appearance White fibers woven into fabrics of varying weight, width and thickness, depending on the style,
with a finish applied.
Color White.
Odor No characteristic odor.
Odor threshold Not relevant due to the physical form of this product.
pH Not relevant due to the physical form of this product.
Melting point 700C / 1292F C
Initial boiling point and rangeNot relevant due to the physical form of this product.
Flash point Not relevant due to the physical form of this product.
Evaporation rate Not relevant due to the physical form of this product.
Evaporation factor Not relevant due to the physical form of this product.
Upper/lower flammability or
explosive limits
Not relevant due to the physical form of this product.
Vapour pressure Not relevant due to the physical form of this product.
Vapour density Not relevant due to the physical form of this product.
Relative density Not relevant due to the physical form of this product.
Solubility(ies) Not relevant due to the physical form of this product.
Auto-ignition temperatureNot relevant due to the physical form of this product.
Viscosity Not relevant due to the physical form of this product.
Explosive properties The mixture does not meet the criteria for explosive in accordance with GHS.
Explosive under the influence
of a flame
The mixture does not meet the criteria for explosive in accordance with GHS.
Oxidising properties Does not meet the criteria for classification as oxidizing.
Comments The indicated values do not necessarily correspond to the product specification. Please refer
to the technical data sheet for specification data.
5/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
10. Stability and reactivity
Stability Stable at normal ambient temperatures and when used as recommended.
Possibility of hazardous
reactions
Not relevant.
Conditions to avoid Avoid heat, flames and other sources of ignition.
Materials to avoid No specific material or group of materials is likely to react with the product to produce a
hazardous situation.
Hazardous decomposition
products
Does not decompose when used and stored as recommended. In an emergency situation
leading to elevated temperature, there may be release of toxic gases and vapors. The
products of combustion and decompostion will depend on other materials present in the fire
and the actual conditions of the fire.
11. Toxicological information
Information on toxicological effects
Toxicological effects Continuous filament fiber is listed by the International Agency for Research on Cancer (IARC)
as a group 3 (not classifiable as a human carcinogen).
Carcinogenicity
IARC carcinogenicity IARC Group 3 Not classifiable as to its carcinogenicity to humans.
Inhalation May cause respiratory system irritation.
Ingestion None expected under normal conditions of use. Ingestion is not an expected route of industrial
exposure.
Skin Contact Contact may cause mechanical irritation, skin redness, itching and drying of the skin.
Prolonged or repeated contact may cause allergic skin reaction, dermatitis and possible
sensitization.
Eye contact May cause mechanical irritation.
Medical considerations Preexisting eye, skin or respiratory disorders may be aggravated by exposure to this product.
12. Ecological Information
Ecotoxicity No ecological data has been determined on the total product.
Toxicity
Toxicity Not regarded as dangerous for the environment.
Persistance and degradability
Persistence and degradabilityNot relevant due to the physical form of this product.
Bioaccumulative potential
Bio-Accumulative PotentialNot relevant due to the physical form of this product.
Mobility in soil
Mobility Not relevant due to the physical form of this product.
6/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
13. Disposal considerations
Waste treatment methods
General information Materials for disposal should be placed in appropriate sealed containers to avoid potential
human and environmental exposure. It is the responsibility of the generator to comply with all
federal, state, provincial and local laws and regulations. We recommend that you contact an
appropriate waste disposal contractor and environmental agency for relevant laws and
regulations. Under the U.S., Resource Conservation and Recovery Act (RCRA), it is the
responsibility of the user of the product to determine at the time of disposal, whether the
product meets relevant waste classification and to assure proper disposal.
Disposal methods Dispose of waste to licensed waste disposal site in accordance with the requirements of the
local Waste Disposal Authority.
14. Transport information
General Not regulated.
UN Number
This product is not dangerous to transport.
UN proper shipping name
This product is not dangerous to transport.
Transport hazard class(es)
This product is not dangerous to transport.
Packing group
This product is not dangerous to transport.
Environmental hazards
Environmentally Hazardous Substance
No.
Special precautions for user
This product is not dangerous to transport.
15. Regulatory information
US Federal Regulations
SARA Section 302 Extremely Hazardous Substances Tier II Threshold Planning Quantities
Not listed.
CERCLA/Superfund, Hazardous Substances/Reportable Quantities (EPA)
Not listed.
SARA Extremely Hazardous Substances EPCRA Reportable Quantities
Not listed.
SARA 313 Emission Reporting
Not listed
7/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
RCRA RCRA Information: Currently, the product is not listed in the federal hazardous waste
regulation 40 CFR, Part 261.33, paragraphs (E) or (F), ie. chemical products that are
considered hazardous if they become waste. State or local hazardous waste regulations may
also apply if they are different from the federal regulation. It is the responsibility of the user of
the product to determine at the time of disposal, whether the product meets relevant waste
classification and to assure proper disposal.
SARA (311/312) Hazard Categories
None.
US State Regulations
California Proposition 65 Carcinogens and Reproductive Toxins
This product contains no listed substances known to the State of California to cause cancer, birth
defects or other reproductive harm, at levels which would require a warning under the statute.
Inventories
US – TSCA
This product is an article as defined by TSCA and is not required to be listed in the TSCA inventory.
US – TSCA 12(b) Export Notification
Not listed.
16. Other information
Abbreviations and acronyms
used in the safety data sheet
ACGIH American Conference of Industrial Hygienists ATE Acute Toxicity Estimate CAS#
Chemical Abstracts Service Number CERCLA Comprehensive Environmental Response,
Compensation, and Liability Act DOT Department of Transportation EmS Emergency
Response Procedures for Ships Carrying Dangerous Goods EPA Environmental Protection
Agency GHS Global Harmonized System HMIS Hazardous Materials Identification System,
IATA International Air Transport Association ICAO International Civil Aviation Organization
IMDG International Maritime Dangerous Goods Kow Octanol-water partition coefficient LC50
Lethal concentration to 50% of a test population LD50 Lethal dose to 50% of a test population
n.o.s. Not otherwise specified OSHA Occupational Safety and Health Administration PBT
Persistent, Bioaccumulative and Toxic substance PNEC Predicted No Effect Concentration
PPE Personal Protection Equipment RCRA Resource Conservation and Recovery Act SADT
Self-accelerating decomposition temperature SARA Superfund Admendments and
Reauthorization Act STOT Specific Target Organ Toxicity (STOT) RE Repeated Exposure
(STOT) SE Single Exposure TSCA Toxic Substance Control Act UN United Nations VOC
Volatile Organic Compound WHMIS Workplace Hazardous Materials Information System
Issued by U.S.A. Product Stewardship department
Revision date 5/1/2015
Revision 0
Hazard statements in fullUSH01 May form combustible dust concentrations in air
ACA HMIS Health rating. Slight hazard. (1)
ACA HMIS Physical hazard
rating.
Normally stable. (0)
ACA HMIS Personal
protection rating.
F
ACA HMIS Flammability
rating.
Will not burn. (0)
8/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
Wherever such words or phrases as “hazardous,” “toxic,” “carcinogen,” etc. appear herein, they are used as a defined or
described under state employee right-to-know laws, Federal OSHA laws or the direct sources for these lawssuch as the
International Agency for Research on Cancer (IARC), the National Toxicology Program (NTP), etc. The use of such words or
phrases should not be taken to mean that we deem or imply any substance or exposure to be toxic, hazardous or otherwise
harmful. Any exposure can only be understood within the entire context of its occurrence, which includes such factors as the
substance’s characteristics as defined in the SDS, amount and duration of exposures, other chemicals present and
preexistingindividual differences in response to the exposure. The data provided in this SDS is based on the information
received from our raw material suppliers and other sources believed to be reliable. We are supplying you this data solely in
compliance with the Federal OSHA Hazard Communication Standard, 29 CFR 1910.1200 and the Federal and State laws as
described in Section 15: Regulatory Information. The information contained in this SDS is proprietary and confidential to
HexcelCorporation. This SDS and the information in it are not to be used for purposes other than compliance with the
Federal OSHA Hazard Communication Standard. If you have received this SDS from any other source than Hexcel
Corporation or its authorized agent, the information contained in it may have been modified from the original document and it
may not be the most current revision. Liability, if any, for use of this product is limited to the terms contained in our sale terms
and conditions. We do not in any way warrant (expressed or implied, including any implied warranty for merchantability or
fitness for a particular purpose) the data contained or the product described in this SDS. Additionally, we do not warrant that
the product will not infringe any patent or other proprietary or property rights of others.
9/9
15750060_SDS.pdf
Revision date: 5/1/2015 Revision: 0
SAFETY DATA SHEET
HexForce F3 and F16 Finish
1. Identification
Product identifier
Product name HexForce F3 and F16 Finish
Product number 20871US-2
Synonyms; trade names Applicable to: E Glass or S Glass with a Chromium (CR3+) Methacrylate Finish applied
Details of the supplier of the safety data sheet
Supplier Hexcel Reinforcements
1913 N. King Street
Seguin
TX 78155
USA
Tel: ++ 830 379 1580
Fax: ++ 830 379 9544
Contact Person 11711 Dublin Blvd, Dublin, California, USA. ++925 551 4900
Emergency telephone number
Emergency telephone To be used only for advice on chemical emergencies, spillages, fires or First Aid:
For emergencies in US/Canada: CHEMTREC 800 424 9300
For emergencies in rest of the world: CARECHEM24 – +44 (0) 1235 239 670
2. Hazard(s) identification
Classification of the substance or mixture
OSHA Regulatory Status This Product is Not Hazardous under the OSHA Hazard Communication Standard.
Physical hazards Combustible Dust – USH01
Health hazards Not Classified
Environmental hazards Not Classified
Label elements
Signal word Warning
Hazard statements USH01 May form combustible dust concentrations in air
Other hazards
Warning! May cause temporary mechanical irritation of the eyes, skin or upper respiratory tract. The American Conference of
Governmental Industrial Hygienists (ACGIH) lists under synthetic vitreous fiber; continous filament glass fibers: 1 f/cc
(respirable) and 5 mg/m3 (inhalable). Warning! Dust generated from machining, grinding or sanding the product may be
combustible and could result in fire and/or explosion should the necessary dust concentration in air and ignition source be
present.
Hazards not otherwise
classified (HNOC)
Fine dust clouds may form explosive mixtures with air.
1/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
3. Composition/information on ingredients
Mixtures
Composition comments Continuous filament glass fiber (type E, R, D, S2) of silicon, aluminum, calcium, boron and
magnesium oxides in a vitreous amorphous state. Filament diameter r>3um CAS 65997-17-
3: >99% w/w
4. First-aid measures
Description of first aid measures
Inhalation With any sign of respiratory distress, affected persons should be taken into fresh air and made
to rest while medical attention is sought.
Ingestion If fiber from the product is ingested, immediately rinse mouth repeatedly with water. If
swallowing has occurred, do not induce vomiting. If requested, give affected person sips of
water. Seek medical attention.
Skin Contact In case of contact with the product or the cured product dust or particulates, immediately wash
skin with mild soap and water. Use a washcloth to help remove fibers. To avoid further
irritation, do not scratch irritated areas. Rubbing or scratching may force the fibers into the
skin. Get medical attention immediately if the irritation persists.
Eye contact contamination by fiber should be removed by flushing with water for at least 15 minutes. Seek
medical attention if irritation persists.
Most important symptoms and effects, both acute and delayed
General information Filaments are mechanical irritants and may induce temporary mouth, nose and throat
irritation. Skin or eye contact may cause itching and temporary irritation. Ingestion may cause
temporary mechanical irritation of the digestive tract. Pre-existing conditions such as
respiratory or skin disorders may be aggravated by exposure to the product or dust/particulate
generated from machining/grinding of the cured product.
Indication of immediate medical attention and special treatment needed
Notes for the doctor No specific recommendations. If in doubt, get medical attention promptly.
5.Fire-fighting measures
Extinguishing media
Suitable extinguishing mediaExtinguish with foam, carbon dioxide, dry powder or water fog.
Unsuitable extinguishing
media
Do not use water jet as an extinguisher, as this will spread the fire.
Special hazards arising from the substance or mixture
Specific hazards No unusual fire or explosion hazards noted.
Hazardous combustion
products
In an emergency situation leading to elevated temperature, there may be release of toxic
gases and vapours. The products of combustion and decomposition will depend on other
materials present in the fire and the actual conditions of the fire.
Advice for firefighters
Special protective equipment
for firefighters
Wear positive-pressure self-contained breathing apparatus (SCBA) and appropriate protective
clothing.
6. Accidental release measures
Personal precautions, protective equipment and emergency procedures
Personal precautions Avoid contact with skin, eyes or clothing.
2/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
Environmental precautions
Environmental precautionsDue to the physical nature of this product, environmental release to drains and water courses
is not possible.
3/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
Methods and material for containment and cleaning up
Methods for cleaning up Clean up material and put into a suitable container and dispose of properly (See Section 13).
Reference to other sectionsFor personal protection, see Section 8. Collect and dispose of spillage as indicated in Section
13.
7. Handling and storage
Precautions for safe handling
Usage precautions Storage: Keep container tightly closed and dry.
Conditions for safe storage, including any incompatibilities
Storage precautions Store in tightly-closed, original container. Keep container dry.
Specific end uses(s)
Specific end use(s) As this product is an article, this section is not applicable.
8. Exposure Controls/personal protection
Control parameters
Occupational exposure limits
Long-term exposure limit (8-hour TWA): 1 f/cc 5 mg/m3 continuous filament glass fibers
Exposure controls
Protective equipment
Appropriate engineering
controls
Provide adequate ventilation.
Eye/face protection Eyewear complying with an approved standard should be worn if a risk assessment indicates
eye contact is possible.
Hand protection It is recommended that gloves are made of the following material: Polyvinyl chloride (PVC).
Rubber (natural, latex).
Other skin and body
protection
Wear appropriate clothing to prevent any possibility of skin contact.
Hygiene measures Wash hands at the end of each work shift and before eating, smoking and using the toilet.
Respiratory protection Wear a suitable dust mask.
4/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
9. Physical and Chemical Properties
Information on basic physical and chemical properties
Appearance White fibers woven into fabrics of varying weight, width and thickness, depending on the style,
with a finish applied.
Color White.
Odor No characteristic odor.
Odor threshold Not relevant due to the physical form of this product.
pH Not relevant due to the physical form of this product.
Melting point 700C / 1292F C
Initial boiling point and rangeNot relevant due to the physical form of this product.
Flash point Not relevant due to the physical form of this product.
Evaporation rate Not relevant due to the physical form of this product.
Evaporation factor Not relevant due to the physical form of this product.
Upper/lower flammability or
explosive limits
Not relevant due to the physical form of this product.
Vapour pressure Not relevant due to the physical form of this product.
Vapour density Not relevant due to the physical form of this product.
Relative density Not relevant due to the physical form of this product.
Solubility(ies) Not relevant due to the physical form of this product.
Auto-ignition temperatureNot relevant due to the physical form of this product.
Viscosity Not relevant due to the physical form of this product.
Explosive properties The mixture does not meet the criteria for explosive in accordance with GHS.
Explosive under the influence
of a flame
The mixture does not meet the criteria for explosive in accordance with GHS.
Oxidising properties Does not meet the criteria for classification as oxidizing.
Comments The indicated values do not necessarily correspond to the product specification. Please refer
to the technical data sheet for specification data.
5/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
10. Stability and reactivity
Stability Stable at normal ambient temperatures and when used as recommended.
Possibility of hazardous
reactions
Not relevant.
Conditions to avoid Avoid heat, flames and other sources of ignition.
Materials to avoid No specific material or group of materials is likely to react with the product to produce a
hazardous situation.
Hazardous decomposition
products
Does not decompose when used and stored as recommended. In an emergency situation
leading to elevated temperature, there may be release of toxic gases and vapors. The
products of combustion and decompostion will depend on other materials present in the fire
and the actual conditions of the fire.
11. Toxicological information
Information on toxicological effects
Toxicological effects Continuous filament fiber is listed by the International Agency for Research on Cancer (IARC)
as a group 3 (not classifiable as a human carcinogen).
Carcinogenicity
IARC carcinogenicity IARC Group 3 Not classifiable as to its carcinogenicity to humans.
Inhalation May cause respiratory system irritation.
Ingestion None expected under normal conditions of use. Ingestion is not an expected route of industrial
exposure.
Skin Contact Contact may cause mechanical irritation, skin redness, itching and drying of the skin.
Prolonged or repeated contact may cause allergic skin reaction, dermatitis and possible
sensitization.
Eye contact May cause mechanical irritation.
Medical considerations Preexisting eye, skin or respiratory disorders may be aggravated by exposure to this product.
12. Ecological Information
Ecotoxicity No ecological data has been determined on the total product.
Toxicity
Toxicity Not regarded as dangerous for the environment.
Persistance and degradability
Persistence and degradabilityNot relevant due to the physical form of this product.
Bioaccumulative potential
Bio-Accumulative PotentialNot relevant due to the physical form of this product.
Mobility in soil
Mobility Not relevant due to the physical form of this product.
6/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
13. Disposal considerations
Waste treatment methods
General information Materials for disposal should be placed in appropriate sealed containers to avoid potential
human and environmental exposure. It is the responsibility of the generator to comply with all
federal, state, provincial and local laws and regulations. We recommend that you contact an
appropriate waste disposal contractor and environmental agency for relevant laws and
regulations. Under the U.S., Resource Conservation and Recovery Act (RCRA), it is the
responsibility of the user of the product to determine at the time of disposal, whether the
product meets relevant waste classification and to assure proper disposal.
Disposal methods Dispose of waste to licensed waste disposal site in accordance with the requirements of the
local Waste Disposal Authority.
14. Transport information
General Not regulated.
UN Number
This product is not dangerous to transport.
UN proper shipping name
This product is not dangerous to transport.
Transport hazard class(es)
This product is not dangerous to transport.
Packing group
This product is not dangerous to transport.
Environmental hazards
Environmentally Hazardous Substance
No.
Special precautions for user
This product is not dangerous to transport.
15. Regulatory information
US Federal Regulations
SARA Section 302 Extremely Hazardous Substances Tier II Threshold Planning Quantities
Not listed.
CERCLA/Superfund, Hazardous Substances/Reportable Quantities (EPA)
Not listed.
SARA Extremely Hazardous Substances EPCRA Reportable Quantities
Not listed.
SARA 313 Emission Reporting
Not listed
7/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
RCRA RCRA Information: Currently, the product is not listed in the federal hazardous waste
regulation 40 CFR, Part 261.33, paragraphs (E) or (F), ie. chemical products that are
considered hazardous if they become waste. State or local hazardous waste regulations may
also apply if they are different from the federal regulation. It is the responsibility of the user of
the product to determine at the time of disposal, whether the product meets relevant waste
classification and to assure proper disposal.
SARA (311/312) Hazard Categories
None.
US State Regulations
California Proposition 65 Carcinogens and Reproductive Toxins
This product contains no listed substances known to the State of California to cause cancer, birth
defects or other reproductive harm, at levels which would require a warning under the statute.
Inventories
US – TSCA
This product is an article as defined by TSCA and is not required to be listed in the TSCA inventory.
US – TSCA 12(b) Export Notification
Not listed.
16. Other information
Abbreviations and acronyms
used in the safety data sheet
ACGIH American Conference of Industrial Hygienists ATE Acute Toxicity Estimate CAS#
Chemical Abstracts Service Number CERCLA Comprehensive Environmental Response,
Compensation, and Liability Act DOT Department of Transportation EmS Emergency
Response Procedures for Ships Carrying Dangerous Goods EPA Environmental Protection
Agency GHS Global Harmonized System HMIS Hazardous Materials Identification System,
IATA International Air Transport Association ICAO International Civil Aviation Organization
IMDG International Maritime Dangerous Goods Kow Octanol-water partition coefficient LC50
Lethal concentration to 50% of a test population LD50 Lethal dose to 50% of a test population
n.o.s. Not otherwise specified OSHA Occupational Safety and Health Administration PBT
Persistent, Bioaccumulative and Toxic substance PNEC Predicted No Effect Concentration
PPE Personal Protection Equipment RCRA Resource Conservation and Recovery Act SADT
Self-accelerating decomposition temperature SARA Superfund Admendments and
Reauthorization Act STOT Specific Target Organ Toxicity (STOT) RE Repeated Exposure
(STOT) SE Single Exposure TSCA Toxic Substance Control Act UN United Nations VOC
Volatile Organic Compound WHMIS Workplace Hazardous Materials Information System
Issued by U.S.A. Product Stewardship department
Revision date 5/1/2015
Revision 0
Hazard statements in fullUSH01 May form combustible dust concentrations in air
ACA HMIS Health rating. Slight hazard. (1)
ACA HMIS Physical hazard
rating.
Normally stable. (0)
ACA HMIS Personal
protection rating.
F
ACA HMIS Flammability
rating.
Will not burn. (0)
8/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
Wherever such words or phrases as “hazardous,” “toxic,” “carcinogen,” etc. appear herein, they are used as a defined or
described under state employee right-to-know laws, Federal OSHA laws or the direct sources for these lawssuch as the
International Agency for Research on Cancer (IARC), the National Toxicology Program (NTP), etc. The use of such words or
phrases should not be taken to mean that we deem or imply any substance or exposure to be toxic, hazardous or otherwise
harmful. Any exposure can only be understood within the entire context of its occurrence, which includes such factors as the
substance’s characteristics as defined in the SDS, amount and duration of exposures, other chemicals present and
preexistingindividual differences in response to the exposure. The data provided in this SDS is based on the information
received from our raw material suppliers and other sources believed to be reliable. We are supplying you this data solely in
compliance with the Federal OSHA Hazard Communication Standard, 29 CFR 1910.1200 and the Federal and State laws as
described in Section 15: Regulatory Information. The information contained in this SDS is proprietary and confidential to
HexcelCorporation. This SDS and the information in it are not to be used for purposes other than compliance with the
Federal OSHA Hazard Communication Standard. If you have received this SDS from any other source than Hexcel
Corporation or its authorized agent, the information contained in it may have been modified from the original document and it
may not be the most current revision. Liability, if any, for use of this product is limited to the terms contained in our sale terms
and conditions. We do not in any way warrant (expressed or implied, including any implied warranty for merchantability or
fitness for a particular purpose) the data contained or the product described in this SDS. Additionally, we do not warrant that
the product will not infringe any patent or other proprietary or property rights of others.
9/9
15750060V_SDS.pdf
SAFETY DATA SHEET
SDS Ref # BGF-015
Prepared: 8/4/2019
Revised: 6/23/2022
Page 1 of 7
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
Section 1: Identification
Chemical Product Name/Identifier: All styles of fiberglass fabric
Finish: 504 – All Versions, 550 – All Versions, PT05, A420
CAS Number: 65997-17-3
Synonyms: Fibrous glass
Recommended Use and Restrictions on Use: Woven textile product used for reinforcement in various
resin systems
Company Information: BGF Industries
230 Slayton, Ave. Suite A-1
Danville, VA 24540
Telephone: 800-476-4845, 434-857-4400
Email: info@bgf.com
Website: http://www.bgf.com
Section 2: Hazards Identification
OSHA HCS Status: This product is a hazardous chemical, as defined by OSHA at 29 CFR 1910.1200.
Hazards identified are based on hazards of the ingredients. The finished product has not been tested.
Relevant Route of Exposure/Target Organs: Dermal, Inhalation
OSHA/GHS Signal Word and Hazard Statements:
WARNING: Causes mild skin irritation. May cause respiratory irritation.
OSHA/GHS Classification and Pictograms:
Skin irritation (Hazard Category 3)
Specific target organ toxicity, single exposure: Respiratory tract irritation (Hazard Category 3)
OSHA/GHS Precautionary Statements:
Prevention
Avoid breathing fibers or dust. Use only outdoors or in a well-ventilated area. Keep containers tightly
closed.
Response
If inhaled: Remove victim to fresh air and keep comfortable for breathing. Call a poison
center/doctor/physician if you feel unwell.
If skin irritation occurs: Get medical advice/attention.
SAFETY DATA SHEET
SDS Ref # BGF-015
Prepared: 8/4/2019
Revised: 6/23/2022
Page 2 of 7
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
Storage
Store in a well-ventilated place. Store locked up. Keep container tightly closed.
Disposal
Dispose of contents/container in accordance with local/regional/national/international regulations.
GHS Hazard and Precautionary Statement Codes: See Section 16.
Section 3: Composition/Information on Ingredients
Chemical Product Name: Fiberglass fabric
Synonyms: Fibrous glass
Component CAS # Max % by weight
Glass, oxide, chemicals 65997-17-3 99.7
Fibrous glass dust * Not assigned Not assigned
Werner chrome complex
A
(Cr
+3
) Not assigned 0.3
Silane Coupling Agents
A
Not assigned 0.3
* Amount will be dependent upon method of handling
A Chemically bound to the fiberglass
Section 4: First-Aid Measures
Skin Contact: Flush with ample cool water followed by washing with mild soap to remove accumulated
fibers.
Eye Contact: Flush with flowing water for 15 minutes seek medical attention.
Inhalation: Move to fresh air.
Ingestion: Not likely to occur through normal use. Should ingestion occur, seek medical attention.
Most Important Symptoms/Effects: Direct skin contact with fibrous glass or its dust may cause
mechanical irritation and transitory dermatitis. Breathing of fibers or dust may cause
mechanical irritation of the mouth, nose, and throat.
Indication of Immediate Medical Attention and Special Treatment Needed: Get medical attention if
product comes into contact with skin or eyes, or if it is inhaled or ingested.
Section 5: Fire-Fighting Measures
Extinguishing Media: Water, dry powder, or foam (needed for packaging only).
Hazardous Combustion Products: Not applicable.
Protective Equipment: Firefighters should be equipped with self-contained breathing apparatus and turn
out gear.
Fire Fighting Procedures/Precautions: Fiberglass itself will not support combustion, but in a sustained
fire, proper protection against products of combustion from the fuel must be worn.
SAFETY DATA SHEET
SDS Ref # BGF-015
Prepared: 8/4/2019
Revised: 6/23/2022
Page 3 of 7
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
Section 6: Accidental Release Measures
Personal Precautions: A release of this product is not expected to pose risks to workers under normal
circumstances. If the material is involved in a fire, or if dusts are produced, no action shall
be taken involving any personal risk or without suitable training. Keep unnecessary and
unprotected personnel from entering. Put on appropriate personal protective equipment.
Protective Equipment: Wear protective gloves/eye protection/skin protection.
Methods/Materials for Containment and Cleaning Up: Dust or loose fibers can be vacuumed or swept
with the aid of a dust suppressant. Dispose of in accordance with all government regulations.
Do not discharge into waterways or sewer systems without proper authority.
Section 7: Handling and Storage
Precautions: This product should be handled under conditions of good industrial hygiene and in
conformity with any local regulations to avoid unnecessary exposure. Use in a well-ventilated
area. Do not breathe dust. Avoid contact with skin.
Storage: Store in a well-ventilated, dry location.
Section 8: Exposure Controls/Personal Protection
Exposure Limits:
Component OSHA/PEL ACGIH/TLV
Fibrous dust 5 mg/m
3
5 mg/m
3
* Dust may be produced during handling
Engineering Controls: Normal area ventilation is sufficient in most cases to keep dust and fiber levels
below the TLV or PEL.
Personal Protection Measures/Equipment:
Skin Protection Barrier creams, gloves, and long sleeve loose fitting clothing may be required
for certain workers who have sensitive skin or contact dermatitis. Work clothing should be
laundered separately from other clothing before reuse.
Eye Protection Not normally required, but as a good safety work practice, eye protection such
as safety glasses/side shields or equivalent whenever use of the product releases airborne
fibrous glass.
Respiratory Protection If airborne fibrous glass exceeds the regulatory limits, or if upper
respiratory irritation occurs, use a N95 particulate filtering respirator.
Other Protection Observe good personal hygiene.
Section 9: Physical and Chemical Properties
Appearance (physical state, color, etc.): Solid, white
Odor: Odorless
SAFETY DATA SHEET
SDS Ref # BGF-015
Prepared: 8/4/2019
Revised: 6/23/2022
Page 4 of 7
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
Odor Threshold: None
pH: None
Melting Point/Freezing Point: >800 C (>1472 F)
Initial Boiling Point: Not applicable
Flash Point: Not applicable
Evaporation Rate: Not applicable
Flammability: Not applicable
Upper/Lower Flammability or Explosive Limits: Not applicable
Vapor Pressure: Not applicable
Vapor Density: Not applicable
Relative Density/Specific Gravity: 2.4 to 2.7
Solubility: Insoluble
Partition Coefficient: Not known
Auto-ignition Temperature: Not known
Decomposition Temperature: Not known
Volatility: Not known
Viscosity: Not applicable
Section 10: Stability and Reactivity
Reactivity: Not self-reactive, water-reactive, or spontaneously combustible
Chemical Stability: This product is stable.
Hazardous Reactions: Under normal conditions of storage and use, hazardous reactions will not occur.
Conditions to Avoid: When exposed to high temperatures may produce hazardous decomposition
products.
Incompatible Materials: Not known
Hazardous Decomposition Products: Fiberglass products may release small amounts of acetic acid
and other organic materials at elevated temperatures.
Hazardous Polymerization: Will not occur
Section 11: Toxicological Information
Relevant Route of Exposure/Target Organs: Dermal, Inhalation
Symptoms: Causes mild skin irritation. May cause irritation of the mouth, nose, and throat after inhalation
exposure.
Delayed and Immediate Effects: Not known
Chronic Effects (Short and Long Term Exposure): Not known
Numerical Measures of Toxicity: None
SAFETY DATA SHEET
SDS Ref # BGF-015
Prepared: 8/4/2019
Revised: 6/23/2022
Page 5 of 7
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
Carcinogenicity: No ingredient is listed as a carcinogen by the NTP, IARC, or OSHA at 29 CFR 1910
Subpart Z.
Mutagenicity: No data available
Reproductive Toxicity: No data available
Section 12: Ecological Information
No data available
Section 13: Disposal Information
Do not discharge into waterways or sewer systems without proper authority. Dispose of in accordance
with all government regulations.
Section 14: Transport Information
Not regulated as a hazardous material/dangerous good for transportation in all modes of transportation (US
DOT, ICAO/IATA, IMO).
Section 15: Regulatory Information
TSCA Inventory Status: Exempt per section 8(a), 710.2(f), and 704.5(a)
SARA Title III Section 302: None
SARA Title III Section 304: None
SARA Title III Section 311/312 Hazard Categories: Immediate (acute)
SARA TITLE III Section 313: This product does not contain components that are subject to the reporting
requirements of Section 313 of the Emergency Planning and Community Right to Know Act of 1986
(EPCRA or SARA Title III) and 40 CFR 372.
CERCLA RQ: Not listed
California Proposition 65: None known
Massachusetts Right-To-Know: Less than reportable quantity
New Jersey Right-To-Know: Less than reportable quantity
Pennsylvania Right-To-Know: Less than reportable quantity
Canada: All components of this product are included on the Domestic Substances List (DSL) or are not
required to be listed on the Canadian DSL.
Europe: All components of this product are included on the European Inventory of Existing Commercial
Chemical Substances (EINECS) or are not required to be listed on the EINECS.
China: All components of this product are included on the Chinese Inventory (IECSC) or are not required
to be listed on the Chinese IECSC.
Japan: All components of this product are included on the Japanese (ENCS) inventory or are not required
to be listed on the Japanese inventory.
Korea: All components of this product are included on the Korean (ECL) inventory or are not required to
be listed on the Korean ECL.
SAFETY DATA SHEET
SDS Ref # BGF-015
Prepared: 8/4/2019
Revised: 6/23/2022
Page 6 of 7
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
Philippines: All components of this product are included on the Philippine (PICCS) or are not required to
be listed on the Philippine PICCS.
Australia: All components of this product are included on the Australian (AICS) or are not required to be
listed on the Australian AICS.
Section 16: Other Information
This product is classified as a Skin Irritant Category 3, however OSHA does not include Category 3
substances in its hazard classification system.
GHS Label Hazard Statement Codes
Signal Word: WARNING
H316: Causes mild skin irritation
H335: May cause respiratory tract irritation.
GHS Label Precautionary Statement Codes
P261: Avoid breathing dusts or fibers.
P271: Use only outdoors or in well-ventilated area.
P304+P340: IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for
breathing.
P312: Call a POISON CENTER or doctor/physician if you feel unwell.
P332+P313: If skin irritation occurs: Get medical advice/attention.
P501: Dispose of contents/container in accordance with local/regional/national/international regulations.
Abbreviations
ACGIH/TLV American Conference of Industrial Hygienists Threshold Limit Value
CAS Chemical Abstracts Service
CERCLA Comprehensive Environmental Response Compensation and Liability Act
CFR US Code of Federal Regulations
DOT US Department of Transportation
EPCRA Emergency Planning and Community Right to Know Act
GHS UN Globally Harmonized System of Classification and Labeling of Chemicals
HCS Hazard Communication Standard
IARC International Agency for Research on Cancer
ICAO/IATA International Civil Aviation Organization/International Air Transport Association
IMO/IMDG International Maritime Organization/International Maritime Dangerous Goods Code
LD50 Lethal dose to half of test animals
SAFETY DATA SHEET
SDS Ref # BGF-015
Prepared: 8/4/2019
Revised: 6/23/2022
Page 7 of 7
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
NTP National Toxicology Program
OSHA US Occupational Safety Health Administration
PEL Permissible exposure limit
RQ Reportable quantity
SARA Superfund Amendments and Reauthorization Act
SDS Safety data sheet
TSCA Toxic Substances Control Act
UN United Nations
US/USA United States
While this company believes that the data contained herein are factual and the opinions expressed are
based on tests and data believed to be reliable, it is the user’s responsibility to determine the safety,
toxicity, and suitability for his or her own use of the product described herein. Since the actual use by
others is beyond our control, no guarantee, expressed or implied, is made by this company as to the
effects of such use, the results to be obtained, or the safety and toxicity of the product, nor does this
company assume any liability arising out of use, by others, of the product referred to herein. Nor is the
information herein to be construed as absolutely complete since additional information may be necessary
or desirable when particular or exceptional conditions or circumstances exist or because of applicable
laws or governmental regulations.
15750050_SDS.pdf
Revision date: 5/1/2015 Revision: 0
SAFETY DATA SHEET
HexForce F3 and F16 Finish
1. Identification
Product identifier
Product name HexForce F3 and F16 Finish
Product number 20871US-2
Synonyms; trade names Applicable to: E Glass or S Glass with a Chromium (CR3+) Methacrylate Finish applied
Details of the supplier of the safety data sheet
Supplier Hexcel Reinforcements
1913 N. King Street
Seguin
TX 78155
USA
Tel: ++ 830 379 1580
Fax: ++ 830 379 9544
Contact Person 11711 Dublin Blvd, Dublin, California, USA. ++925 551 4900
Emergency telephone number
Emergency telephone To be used only for advice on chemical emergencies, spillages, fires or First Aid:
For emergencies in US/Canada: CHEMTREC 800 424 9300
For emergencies in rest of the world: CARECHEM24 – +44 (0) 1235 239 670
2. Hazard(s) identification
Classification of the substance or mixture
OSHA Regulatory Status This Product is Not Hazardous under the OSHA Hazard Communication Standard.
Physical hazards Combustible Dust – USH01
Health hazards Not Classified
Environmental hazards Not Classified
Label elements
Signal word Warning
Hazard statements USH01 May form combustible dust concentrations in air
Other hazards
Warning! May cause temporary mechanical irritation of the eyes, skin or upper respiratory tract. The American Conference of
Governmental Industrial Hygienists (ACGIH) lists under synthetic vitreous fiber; continous filament glass fibers: 1 f/cc
(respirable) and 5 mg/m3 (inhalable). Warning! Dust generated from machining, grinding or sanding the product may be
combustible and could result in fire and/or explosion should the necessary dust concentration in air and ignition source be
present.
Hazards not otherwise
classified (HNOC)
Fine dust clouds may form explosive mixtures with air.
1/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
3. Composition/information on ingredients
Mixtures
Composition comments Continuous filament glass fiber (type E, R, D, S2) of silicon, aluminum, calcium, boron and
magnesium oxides in a vitreous amorphous state. Filament diameter r>3um CAS 65997-17-
3: >99% w/w
4. First-aid measures
Description of first aid measures
Inhalation With any sign of respiratory distress, affected persons should be taken into fresh air and made
to rest while medical attention is sought.
Ingestion If fiber from the product is ingested, immediately rinse mouth repeatedly with water. If
swallowing has occurred, do not induce vomiting. If requested, give affected person sips of
water. Seek medical attention.
Skin Contact In case of contact with the product or the cured product dust or particulates, immediately wash
skin with mild soap and water. Use a washcloth to help remove fibers. To avoid further
irritation, do not scratch irritated areas. Rubbing or scratching may force the fibers into the
skin. Get medical attention immediately if the irritation persists.
Eye contact contamination by fiber should be removed by flushing with water for at least 15 minutes. Seek
medical attention if irritation persists.
Most important symptoms and effects, both acute and delayed
General information Filaments are mechanical irritants and may induce temporary mouth, nose and throat
irritation. Skin or eye contact may cause itching and temporary irritation. Ingestion may cause
temporary mechanical irritation of the digestive tract. Pre-existing conditions such as
respiratory or skin disorders may be aggravated by exposure to the product or dust/particulate
generated from machining/grinding of the cured product.
Indication of immediate medical attention and special treatment needed
Notes for the doctor No specific recommendations. If in doubt, get medical attention promptly.
5.Fire-fighting measures
Extinguishing media
Suitable extinguishing mediaExtinguish with foam, carbon dioxide, dry powder or water fog.
Unsuitable extinguishing
media
Do not use water jet as an extinguisher, as this will spread the fire.
Special hazards arising from the substance or mixture
Specific hazards No unusual fire or explosion hazards noted.
Hazardous combustion
products
In an emergency situation leading to elevated temperature, there may be release of toxic
gases and vapours. The products of combustion and decomposition will depend on other
materials present in the fire and the actual conditions of the fire.
Advice for firefighters
Special protective equipment
for firefighters
Wear positive-pressure self-contained breathing apparatus (SCBA) and appropriate protective
clothing.
6. Accidental release measures
Personal precautions, protective equipment and emergency procedures
Personal precautions Avoid contact with skin, eyes or clothing.
2/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
Environmental precautions
Environmental precautionsDue to the physical nature of this product, environmental release to drains and water courses
is not possible.
3/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
Methods and material for containment and cleaning up
Methods for cleaning up Clean up material and put into a suitable container and dispose of properly (See Section 13).
Reference to other sectionsFor personal protection, see Section 8. Collect and dispose of spillage as indicated in Section
13.
7. Handling and storage
Precautions for safe handling
Usage precautions Storage: Keep container tightly closed and dry.
Conditions for safe storage, including any incompatibilities
Storage precautions Store in tightly-closed, original container. Keep container dry.
Specific end uses(s)
Specific end use(s) As this product is an article, this section is not applicable.
8. Exposure Controls/personal protection
Control parameters
Occupational exposure limits
Long-term exposure limit (8-hour TWA): 1 f/cc 5 mg/m3 continuous filament glass fibers
Exposure controls
Protective equipment
Appropriate engineering
controls
Provide adequate ventilation.
Eye/face protection Eyewear complying with an approved standard should be worn if a risk assessment indicates
eye contact is possible.
Hand protection It is recommended that gloves are made of the following material: Polyvinyl chloride (PVC).
Rubber (natural, latex).
Other skin and body
protection
Wear appropriate clothing to prevent any possibility of skin contact.
Hygiene measures Wash hands at the end of each work shift and before eating, smoking and using the toilet.
Respiratory protection Wear a suitable dust mask.
4/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
9. Physical and Chemical Properties
Information on basic physical and chemical properties
Appearance White fibers woven into fabrics of varying weight, width and thickness, depending on the style,
with a finish applied.
Color White.
Odor No characteristic odor.
Odor threshold Not relevant due to the physical form of this product.
pH Not relevant due to the physical form of this product.
Melting point 700C / 1292F C
Initial boiling point and rangeNot relevant due to the physical form of this product.
Flash point Not relevant due to the physical form of this product.
Evaporation rate Not relevant due to the physical form of this product.
Evaporation factor Not relevant due to the physical form of this product.
Upper/lower flammability or
explosive limits
Not relevant due to the physical form of this product.
Vapour pressure Not relevant due to the physical form of this product.
Vapour density Not relevant due to the physical form of this product.
Relative density Not relevant due to the physical form of this product.
Solubility(ies) Not relevant due to the physical form of this product.
Auto-ignition temperatureNot relevant due to the physical form of this product.
Viscosity Not relevant due to the physical form of this product.
Explosive properties The mixture does not meet the criteria for explosive in accordance with GHS.
Explosive under the influence
of a flame
The mixture does not meet the criteria for explosive in accordance with GHS.
Oxidising properties Does not meet the criteria for classification as oxidizing.
Comments The indicated values do not necessarily correspond to the product specification. Please refer
to the technical data sheet for specification data.
5/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
10. Stability and reactivity
Stability Stable at normal ambient temperatures and when used as recommended.
Possibility of hazardous
reactions
Not relevant.
Conditions to avoid Avoid heat, flames and other sources of ignition.
Materials to avoid No specific material or group of materials is likely to react with the product to produce a
hazardous situation.
Hazardous decomposition
products
Does not decompose when used and stored as recommended. In an emergency situation
leading to elevated temperature, there may be release of toxic gases and vapors. The
products of combustion and decompostion will depend on other materials present in the fire
and the actual conditions of the fire.
11. Toxicological information
Information on toxicological effects
Toxicological effects Continuous filament fiber is listed by the International Agency for Research on Cancer (IARC)
as a group 3 (not classifiable as a human carcinogen).
Carcinogenicity
IARC carcinogenicity IARC Group 3 Not classifiable as to its carcinogenicity to humans.
Inhalation May cause respiratory system irritation.
Ingestion None expected under normal conditions of use. Ingestion is not an expected route of industrial
exposure.
Skin Contact Contact may cause mechanical irritation, skin redness, itching and drying of the skin.
Prolonged or repeated contact may cause allergic skin reaction, dermatitis and possible
sensitization.
Eye contact May cause mechanical irritation.
Medical considerations Preexisting eye, skin or respiratory disorders may be aggravated by exposure to this product.
12. Ecological Information
Ecotoxicity No ecological data has been determined on the total product.
Toxicity
Toxicity Not regarded as dangerous for the environment.
Persistance and degradability
Persistence and degradabilityNot relevant due to the physical form of this product.
Bioaccumulative potential
Bio-Accumulative PotentialNot relevant due to the physical form of this product.
Mobility in soil
Mobility Not relevant due to the physical form of this product.
6/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
13. Disposal considerations
Waste treatment methods
General information Materials for disposal should be placed in appropriate sealed containers to avoid potential
human and environmental exposure. It is the responsibility of the generator to comply with all
federal, state, provincial and local laws and regulations. We recommend that you contact an
appropriate waste disposal contractor and environmental agency for relevant laws and
regulations. Under the U.S., Resource Conservation and Recovery Act (RCRA), it is the
responsibility of the user of the product to determine at the time of disposal, whether the
product meets relevant waste classification and to assure proper disposal.
Disposal methods Dispose of waste to licensed waste disposal site in accordance with the requirements of the
local Waste Disposal Authority.
14. Transport information
General Not regulated.
UN Number
This product is not dangerous to transport.
UN proper shipping name
This product is not dangerous to transport.
Transport hazard class(es)
This product is not dangerous to transport.
Packing group
This product is not dangerous to transport.
Environmental hazards
Environmentally Hazardous Substance
No.
Special precautions for user
This product is not dangerous to transport.
15. Regulatory information
US Federal Regulations
SARA Section 302 Extremely Hazardous Substances Tier II Threshold Planning Quantities
Not listed.
CERCLA/Superfund, Hazardous Substances/Reportable Quantities (EPA)
Not listed.
SARA Extremely Hazardous Substances EPCRA Reportable Quantities
Not listed.
SARA 313 Emission Reporting
Not listed
7/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
RCRA RCRA Information: Currently, the product is not listed in the federal hazardous waste
regulation 40 CFR, Part 261.33, paragraphs (E) or (F), ie. chemical products that are
considered hazardous if they become waste. State or local hazardous waste regulations may
also apply if they are different from the federal regulation. It is the responsibility of the user of
the product to determine at the time of disposal, whether the product meets relevant waste
classification and to assure proper disposal.
SARA (311/312) Hazard Categories
None.
US State Regulations
California Proposition 65 Carcinogens and Reproductive Toxins
This product contains no listed substances known to the State of California to cause cancer, birth
defects or other reproductive harm, at levels which would require a warning under the statute.
Inventories
US – TSCA
This product is an article as defined by TSCA and is not required to be listed in the TSCA inventory.
US – TSCA 12(b) Export Notification
Not listed.
16. Other information
Abbreviations and acronyms
used in the safety data sheet
ACGIH American Conference of Industrial Hygienists ATE Acute Toxicity Estimate CAS#
Chemical Abstracts Service Number CERCLA Comprehensive Environmental Response,
Compensation, and Liability Act DOT Department of Transportation EmS Emergency
Response Procedures for Ships Carrying Dangerous Goods EPA Environmental Protection
Agency GHS Global Harmonized System HMIS Hazardous Materials Identification System,
IATA International Air Transport Association ICAO International Civil Aviation Organization
IMDG International Maritime Dangerous Goods Kow Octanol-water partition coefficient LC50
Lethal concentration to 50% of a test population LD50 Lethal dose to 50% of a test population
n.o.s. Not otherwise specified OSHA Occupational Safety and Health Administration PBT
Persistent, Bioaccumulative and Toxic substance PNEC Predicted No Effect Concentration
PPE Personal Protection Equipment RCRA Resource Conservation and Recovery Act SADT
Self-accelerating decomposition temperature SARA Superfund Admendments and
Reauthorization Act STOT Specific Target Organ Toxicity (STOT) RE Repeated Exposure
(STOT) SE Single Exposure TSCA Toxic Substance Control Act UN United Nations VOC
Volatile Organic Compound WHMIS Workplace Hazardous Materials Information System
Issued by U.S.A. Product Stewardship department
Revision date 5/1/2015
Revision 0
Hazard statements in fullUSH01 May form combustible dust concentrations in air
ACA HMIS Health rating. Slight hazard. (1)
ACA HMIS Physical hazard
rating.
Normally stable. (0)
ACA HMIS Personal
protection rating.
F
ACA HMIS Flammability
rating.
Will not burn. (0)
8/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
Wherever such words or phrases as “hazardous,” “toxic,” “carcinogen,” etc. appear herein, they are used as a defined or
described under state employee right-to-know laws, Federal OSHA laws or the direct sources for these lawssuch as the
International Agency for Research on Cancer (IARC), the National Toxicology Program (NTP), etc. The use of such words or
phrases should not be taken to mean that we deem or imply any substance or exposure to be toxic, hazardous or otherwise
harmful. Any exposure can only be understood within the entire context of its occurrence, which includes such factors as the
substance’s characteristics as defined in the SDS, amount and duration of exposures, other chemicals present and
preexistingindividual differences in response to the exposure. The data provided in this SDS is based on the information
received from our raw material suppliers and other sources believed to be reliable. We are supplying you this data solely in
compliance with the Federal OSHA Hazard Communication Standard, 29 CFR 1910.1200 and the Federal and State laws as
described in Section 15: Regulatory Information. The information contained in this SDS is proprietary and confidential to
HexcelCorporation. This SDS and the information in it are not to be used for purposes other than compliance with the
Federal OSHA Hazard Communication Standard. If you have received this SDS from any other source than Hexcel
Corporation or its authorized agent, the information contained in it may have been modified from the original document and it
may not be the most current revision. Liability, if any, for use of this product is limited to the terms contained in our sale terms
and conditions. We do not in any way warrant (expressed or implied, including any implied warranty for merchantability or
fitness for a particular purpose) the data contained or the product described in this SDS. Additionally, we do not warrant that
the product will not infringe any patent or other proprietary or property rights of others.
9/9
15750050V_SDS.pdf
SAFETY DATA SHEET
SDS Ref # BGF-015
Prepared: 8/4/2019
Revised: 6/23/2022
Page 1 of 7
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
Section 1: Identification
Chemical Product Name/Identifier: All styles of fiberglass fabric
Finish: 504 – All Versions, 550 – All Versions, PT05, A420
CAS Number: 65997-17-3
Synonyms: Fibrous glass
Recommended Use and Restrictions on Use: Woven textile product used for reinforcement in various
resin systems
Company Information: BGF Industries
230 Slayton, Ave. Suite A-1
Danville, VA 24540
Telephone: 800-476-4845, 434-857-4400
Email: info@bgf.com
Website: http://www.bgf.com
Section 2: Hazards Identification
OSHA HCS Status: This product is a hazardous chemical, as defined by OSHA at 29 CFR 1910.1200.
Hazards identified are based on hazards of the ingredients. The finished product has not been tested.
Relevant Route of Exposure/Target Organs: Dermal, Inhalation
OSHA/GHS Signal Word and Hazard Statements:
WARNING: Causes mild skin irritation. May cause respiratory irritation.
OSHA/GHS Classification and Pictograms:
Skin irritation (Hazard Category 3)
Specific target organ toxicity, single exposure: Respiratory tract irritation (Hazard Category 3)
OSHA/GHS Precautionary Statements:
Prevention
Avoid breathing fibers or dust. Use only outdoors or in a well-ventilated area. Keep containers tightly
closed.
Response
If inhaled: Remove victim to fresh air and keep comfortable for breathing. Call a poison
center/doctor/physician if you feel unwell.
If skin irritation occurs: Get medical advice/attention.
SAFETY DATA SHEET
SDS Ref # BGF-015
Prepared: 8/4/2019
Revised: 6/23/2022
Page 2 of 7
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
Storage
Store in a well-ventilated place. Store locked up. Keep container tightly closed.
Disposal
Dispose of contents/container in accordance with local/regional/national/international regulations.
GHS Hazard and Precautionary Statement Codes: See Section 16.
Section 3: Composition/Information on Ingredients
Chemical Product Name: Fiberglass fabric
Synonyms: Fibrous glass
Component CAS # Max % by weight
Glass, oxide, chemicals 65997-17-3 99.7
Fibrous glass dust * Not assigned Not assigned
Werner chrome complex
A
(Cr
+3
) Not assigned 0.3
Silane Coupling Agents
A
Not assigned 0.3
* Amount will be dependent upon method of handling
A Chemically bound to the fiberglass
Section 4: First-Aid Measures
Skin Contact: Flush with ample cool water followed by washing with mild soap to remove accumulated
fibers.
Eye Contact: Flush with flowing water for 15 minutes seek medical attention.
Inhalation: Move to fresh air.
Ingestion: Not likely to occur through normal use. Should ingestion occur, seek medical attention.
Most Important Symptoms/Effects: Direct skin contact with fibrous glass or its dust may cause
mechanical irritation and transitory dermatitis. Breathing of fibers or dust may cause
mechanical irritation of the mouth, nose, and throat.
Indication of Immediate Medical Attention and Special Treatment Needed: Get medical attention if
product comes into contact with skin or eyes, or if it is inhaled or ingested.
Section 5: Fire-Fighting Measures
Extinguishing Media: Water, dry powder, or foam (needed for packaging only).
Hazardous Combustion Products: Not applicable.
Protective Equipment: Firefighters should be equipped with self-contained breathing apparatus and turn
out gear.
Fire Fighting Procedures/Precautions: Fiberglass itself will not support combustion, but in a sustained
fire, proper protection against products of combustion from the fuel must be worn.
SAFETY DATA SHEET
SDS Ref # BGF-015
Prepared: 8/4/2019
Revised: 6/23/2022
Page 3 of 7
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
Section 6: Accidental Release Measures
Personal Precautions: A release of this product is not expected to pose risks to workers under normal
circumstances. If the material is involved in a fire, or if dusts are produced, no action shall
be taken involving any personal risk or without suitable training. Keep unnecessary and
unprotected personnel from entering. Put on appropriate personal protective equipment.
Protective Equipment: Wear protective gloves/eye protection/skin protection.
Methods/Materials for Containment and Cleaning Up: Dust or loose fibers can be vacuumed or swept
with the aid of a dust suppressant. Dispose of in accordance with all government regulations.
Do not discharge into waterways or sewer systems without proper authority.
Section 7: Handling and Storage
Precautions: This product should be handled under conditions of good industrial hygiene and in
conformity with any local regulations to avoid unnecessary exposure. Use in a well-ventilated
area. Do not breathe dust. Avoid contact with skin.
Storage: Store in a well-ventilated, dry location.
Section 8: Exposure Controls/Personal Protection
Exposure Limits:
Component OSHA/PEL ACGIH/TLV
Fibrous dust 5 mg/m
3
5 mg/m
3
* Dust may be produced during handling
Engineering Controls: Normal area ventilation is sufficient in most cases to keep dust and fiber levels
below the TLV or PEL.
Personal Protection Measures/Equipment:
Skin Protection Barrier creams, gloves, and long sleeve loose fitting clothing may be required
for certain workers who have sensitive skin or contact dermatitis. Work clothing should be
laundered separately from other clothing before reuse.
Eye Protection Not normally required, but as a good safety work practice, eye protection such
as safety glasses/side shields or equivalent whenever use of the product releases airborne
fibrous glass.
Respiratory Protection If airborne fibrous glass exceeds the regulatory limits, or if upper
respiratory irritation occurs, use a N95 particulate filtering respirator.
Other Protection Observe good personal hygiene.
Section 9: Physical and Chemical Properties
Appearance (physical state, color, etc.): Solid, white
Odor: Odorless
SAFETY DATA SHEET
SDS Ref # BGF-015
Prepared: 8/4/2019
Revised: 6/23/2022
Page 4 of 7
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
Odor Threshold: None
pH: None
Melting Point/Freezing Point: >800 C (>1472 F)
Initial Boiling Point: Not applicable
Flash Point: Not applicable
Evaporation Rate: Not applicable
Flammability: Not applicable
Upper/Lower Flammability or Explosive Limits: Not applicable
Vapor Pressure: Not applicable
Vapor Density: Not applicable
Relative Density/Specific Gravity: 2.4 to 2.7
Solubility: Insoluble
Partition Coefficient: Not known
Auto-ignition Temperature: Not known
Decomposition Temperature: Not known
Volatility: Not known
Viscosity: Not applicable
Section 10: Stability and Reactivity
Reactivity: Not self-reactive, water-reactive, or spontaneously combustible
Chemical Stability: This product is stable.
Hazardous Reactions: Under normal conditions of storage and use, hazardous reactions will not occur.
Conditions to Avoid: When exposed to high temperatures may produce hazardous decomposition
products.
Incompatible Materials: Not known
Hazardous Decomposition Products: Fiberglass products may release small amounts of acetic acid
and other organic materials at elevated temperatures.
Hazardous Polymerization: Will not occur
Section 11: Toxicological Information
Relevant Route of Exposure/Target Organs: Dermal, Inhalation
Symptoms: Causes mild skin irritation. May cause irritation of the mouth, nose, and throat after inhalation
exposure.
Delayed and Immediate Effects: Not known
Chronic Effects (Short and Long Term Exposure): Not known
Numerical Measures of Toxicity: None
SAFETY DATA SHEET
SDS Ref # BGF-015
Prepared: 8/4/2019
Revised: 6/23/2022
Page 5 of 7
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
Carcinogenicity: No ingredient is listed as a carcinogen by the NTP, IARC, or OSHA at 29 CFR 1910
Subpart Z.
Mutagenicity: No data available
Reproductive Toxicity: No data available
Section 12: Ecological Information
No data available
Section 13: Disposal Information
Do not discharge into waterways or sewer systems without proper authority. Dispose of in accordance
with all government regulations.
Section 14: Transport Information
Not regulated as a hazardous material/dangerous good for transportation in all modes of transportation (US
DOT, ICAO/IATA, IMO).
Section 15: Regulatory Information
TSCA Inventory Status: Exempt per section 8(a), 710.2(f), and 704.5(a)
SARA Title III Section 302: None
SARA Title III Section 304: None
SARA Title III Section 311/312 Hazard Categories: Immediate (acute)
SARA TITLE III Section 313: This product does not contain components that are subject to the reporting
requirements of Section 313 of the Emergency Planning and Community Right to Know Act of 1986
(EPCRA or SARA Title III) and 40 CFR 372.
CERCLA RQ: Not listed
California Proposition 65: None known
Massachusetts Right-To-Know: Less than reportable quantity
New Jersey Right-To-Know: Less than reportable quantity
Pennsylvania Right-To-Know: Less than reportable quantity
Canada: All components of this product are included on the Domestic Substances List (DSL) or are not
required to be listed on the Canadian DSL.
Europe: All components of this product are included on the European Inventory of Existing Commercial
Chemical Substances (EINECS) or are not required to be listed on the EINECS.
China: All components of this product are included on the Chinese Inventory (IECSC) or are not required
to be listed on the Chinese IECSC.
Japan: All components of this product are included on the Japanese (ENCS) inventory or are not required
to be listed on the Japanese inventory.
Korea: All components of this product are included on the Korean (ECL) inventory or are not required to
be listed on the Korean ECL.
SAFETY DATA SHEET
SDS Ref # BGF-015
Prepared: 8/4/2019
Revised: 6/23/2022
Page 6 of 7
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
Philippines: All components of this product are included on the Philippine (PICCS) or are not required to
be listed on the Philippine PICCS.
Australia: All components of this product are included on the Australian (AICS) or are not required to be
listed on the Australian AICS.
Section 16: Other Information
This product is classified as a Skin Irritant Category 3, however OSHA does not include Category 3
substances in its hazard classification system.
GHS Label Hazard Statement Codes
Signal Word: WARNING
H316: Causes mild skin irritation
H335: May cause respiratory tract irritation.
GHS Label Precautionary Statement Codes
P261: Avoid breathing dusts or fibers.
P271: Use only outdoors or in well-ventilated area.
P304+P340: IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for
breathing.
P312: Call a POISON CENTER or doctor/physician if you feel unwell.
P332+P313: If skin irritation occurs: Get medical advice/attention.
P501: Dispose of contents/container in accordance with local/regional/national/international regulations.
Abbreviations
ACGIH/TLV American Conference of Industrial Hygienists Threshold Limit Value
CAS Chemical Abstracts Service
CERCLA Comprehensive Environmental Response Compensation and Liability Act
CFR US Code of Federal Regulations
DOT US Department of Transportation
EPCRA Emergency Planning and Community Right to Know Act
GHS UN Globally Harmonized System of Classification and Labeling of Chemicals
HCS Hazard Communication Standard
IARC International Agency for Research on Cancer
ICAO/IATA International Civil Aviation Organization/International Air Transport Association
IMO/IMDG International Maritime Organization/International Maritime Dangerous Goods Code
LD50 Lethal dose to half of test animals
SAFETY DATA SHEET
SDS Ref # BGF-015
Prepared: 8/4/2019
Revised: 6/23/2022
Page 7 of 7
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
NTP National Toxicology Program
OSHA US Occupational Safety Health Administration
PEL Permissible exposure limit
RQ Reportable quantity
SARA Superfund Amendments and Reauthorization Act
SDS Safety data sheet
TSCA Toxic Substances Control Act
UN United Nations
US/USA United States
While this company believes that the data contained herein are factual and the opinions expressed are
based on tests and data believed to be reliable, it is the user’s responsibility to determine the safety,
toxicity, and suitability for his or her own use of the product described herein. Since the actual use by
others is beyond our control, no guarantee, expressed or implied, is made by this company as to the
effects of such use, the results to be obtained, or the safety and toxicity of the product, nor does this
company assume any liability arising out of use, by others, of the product referred to herein. Nor is the
information herein to be construed as absolutely complete since additional information may be necessary
or desirable when particular or exceptional conditions or circumstances exist or because of applicable
laws or governmental regulations.
15750038_SDS.pdf
Revision date: 5/1/2015 Revision: 0
SAFETY DATA SHEET
HexForce F3 and F16 Finish
1. Identification
Product identifier
Product name HexForce F3 and F16 Finish
Product number 20871US-2
Synonyms; trade names Applicable to: E Glass or S Glass with a Chromium (CR3+) Methacrylate Finish applied
Details of the supplier of the safety data sheet
Supplier Hexcel Reinforcements
1913 N. King Street
Seguin
TX 78155
USA
Tel: ++ 830 379 1580
Fax: ++ 830 379 9544
Contact Person 11711 Dublin Blvd, Dublin, California, USA. ++925 551 4900
Emergency telephone number
Emergency telephone To be used only for advice on chemical emergencies, spillages, fires or First Aid:
For emergencies in US/Canada: CHEMTREC 800 424 9300
For emergencies in rest of the world: CARECHEM24 – +44 (0) 1235 239 670
2. Hazard(s) identification
Classification of the substance or mixture
OSHA Regulatory Status This Product is Not Hazardous under the OSHA Hazard Communication Standard.
Physical hazards Combustible Dust – USH01
Health hazards Not Classified
Environmental hazards Not Classified
Label elements
Signal word Warning
Hazard statements USH01 May form combustible dust concentrations in air
Other hazards
Warning! May cause temporary mechanical irritation of the eyes, skin or upper respiratory tract. The American Conference of
Governmental Industrial Hygienists (ACGIH) lists under synthetic vitreous fiber; continous filament glass fibers: 1 f/cc
(respirable) and 5 mg/m3 (inhalable). Warning! Dust generated from machining, grinding or sanding the product may be
combustible and could result in fire and/or explosion should the necessary dust concentration in air and ignition source be
present.
Hazards not otherwise
classified (HNOC)
Fine dust clouds may form explosive mixtures with air.
1/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
3. Composition/information on ingredients
Mixtures
Composition comments Continuous filament glass fiber (type E, R, D, S2) of silicon, aluminum, calcium, boron and
magnesium oxides in a vitreous amorphous state. Filament diameter r>3um CAS 65997-17-
3: >99% w/w
4. First-aid measures
Description of first aid measures
Inhalation With any sign of respiratory distress, affected persons should be taken into fresh air and made
to rest while medical attention is sought.
Ingestion If fiber from the product is ingested, immediately rinse mouth repeatedly with water. If
swallowing has occurred, do not induce vomiting. If requested, give affected person sips of
water. Seek medical attention.
Skin Contact In case of contact with the product or the cured product dust or particulates, immediately wash
skin with mild soap and water. Use a washcloth to help remove fibers. To avoid further
irritation, do not scratch irritated areas. Rubbing or scratching may force the fibers into the
skin. Get medical attention immediately if the irritation persists.
Eye contact contamination by fiber should be removed by flushing with water for at least 15 minutes. Seek
medical attention if irritation persists.
Most important symptoms and effects, both acute and delayed
General information Filaments are mechanical irritants and may induce temporary mouth, nose and throat
irritation. Skin or eye contact may cause itching and temporary irritation. Ingestion may cause
temporary mechanical irritation of the digestive tract. Pre-existing conditions such as
respiratory or skin disorders may be aggravated by exposure to the product or dust/particulate
generated from machining/grinding of the cured product.
Indication of immediate medical attention and special treatment needed
Notes for the doctor No specific recommendations. If in doubt, get medical attention promptly.
5.Fire-fighting measures
Extinguishing media
Suitable extinguishing mediaExtinguish with foam, carbon dioxide, dry powder or water fog.
Unsuitable extinguishing
media
Do not use water jet as an extinguisher, as this will spread the fire.
Special hazards arising from the substance or mixture
Specific hazards No unusual fire or explosion hazards noted.
Hazardous combustion
products
In an emergency situation leading to elevated temperature, there may be release of toxic
gases and vapours. The products of combustion and decomposition will depend on other
materials present in the fire and the actual conditions of the fire.
Advice for firefighters
Special protective equipment
for firefighters
Wear positive-pressure self-contained breathing apparatus (SCBA) and appropriate protective
clothing.
6. Accidental release measures
Personal precautions, protective equipment and emergency procedures
Personal precautions Avoid contact with skin, eyes or clothing.
2/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
Environmental precautions
Environmental precautionsDue to the physical nature of this product, environmental release to drains and water courses
is not possible.
3/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
Methods and material for containment and cleaning up
Methods for cleaning up Clean up material and put into a suitable container and dispose of properly (See Section 13).
Reference to other sectionsFor personal protection, see Section 8. Collect and dispose of spillage as indicated in Section
13.
7. Handling and storage
Precautions for safe handling
Usage precautions Storage: Keep container tightly closed and dry.
Conditions for safe storage, including any incompatibilities
Storage precautions Store in tightly-closed, original container. Keep container dry.
Specific end uses(s)
Specific end use(s) As this product is an article, this section is not applicable.
8. Exposure Controls/personal protection
Control parameters
Occupational exposure limits
Long-term exposure limit (8-hour TWA): 1 f/cc 5 mg/m3 continuous filament glass fibers
Exposure controls
Protective equipment
Appropriate engineering
controls
Provide adequate ventilation.
Eye/face protection Eyewear complying with an approved standard should be worn if a risk assessment indicates
eye contact is possible.
Hand protection It is recommended that gloves are made of the following material: Polyvinyl chloride (PVC).
Rubber (natural, latex).
Other skin and body
protection
Wear appropriate clothing to prevent any possibility of skin contact.
Hygiene measures Wash hands at the end of each work shift and before eating, smoking and using the toilet.
Respiratory protection Wear a suitable dust mask.
4/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
9. Physical and Chemical Properties
Information on basic physical and chemical properties
Appearance White fibers woven into fabrics of varying weight, width and thickness, depending on the style,
with a finish applied.
Color White.
Odor No characteristic odor.
Odor threshold Not relevant due to the physical form of this product.
pH Not relevant due to the physical form of this product.
Melting point 700C / 1292F C
Initial boiling point and rangeNot relevant due to the physical form of this product.
Flash point Not relevant due to the physical form of this product.
Evaporation rate Not relevant due to the physical form of this product.
Evaporation factor Not relevant due to the physical form of this product.
Upper/lower flammability or
explosive limits
Not relevant due to the physical form of this product.
Vapour pressure Not relevant due to the physical form of this product.
Vapour density Not relevant due to the physical form of this product.
Relative density Not relevant due to the physical form of this product.
Solubility(ies) Not relevant due to the physical form of this product.
Auto-ignition temperatureNot relevant due to the physical form of this product.
Viscosity Not relevant due to the physical form of this product.
Explosive properties The mixture does not meet the criteria for explosive in accordance with GHS.
Explosive under the influence
of a flame
The mixture does not meet the criteria for explosive in accordance with GHS.
Oxidising properties Does not meet the criteria for classification as oxidizing.
Comments The indicated values do not necessarily correspond to the product specification. Please refer
to the technical data sheet for specification data.
5/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
10. Stability and reactivity
Stability Stable at normal ambient temperatures and when used as recommended.
Possibility of hazardous
reactions
Not relevant.
Conditions to avoid Avoid heat, flames and other sources of ignition.
Materials to avoid No specific material or group of materials is likely to react with the product to produce a
hazardous situation.
Hazardous decomposition
products
Does not decompose when used and stored as recommended. In an emergency situation
leading to elevated temperature, there may be release of toxic gases and vapors. The
products of combustion and decompostion will depend on other materials present in the fire
and the actual conditions of the fire.
11. Toxicological information
Information on toxicological effects
Toxicological effects Continuous filament fiber is listed by the International Agency for Research on Cancer (IARC)
as a group 3 (not classifiable as a human carcinogen).
Carcinogenicity
IARC carcinogenicity IARC Group 3 Not classifiable as to its carcinogenicity to humans.
Inhalation May cause respiratory system irritation.
Ingestion None expected under normal conditions of use. Ingestion is not an expected route of industrial
exposure.
Skin Contact Contact may cause mechanical irritation, skin redness, itching and drying of the skin.
Prolonged or repeated contact may cause allergic skin reaction, dermatitis and possible
sensitization.
Eye contact May cause mechanical irritation.
Medical considerations Preexisting eye, skin or respiratory disorders may be aggravated by exposure to this product.
12. Ecological Information
Ecotoxicity No ecological data has been determined on the total product.
Toxicity
Toxicity Not regarded as dangerous for the environment.
Persistance and degradability
Persistence and degradabilityNot relevant due to the physical form of this product.
Bioaccumulative potential
Bio-Accumulative PotentialNot relevant due to the physical form of this product.
Mobility in soil
Mobility Not relevant due to the physical form of this product.
6/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
13. Disposal considerations
Waste treatment methods
General information Materials for disposal should be placed in appropriate sealed containers to avoid potential
human and environmental exposure. It is the responsibility of the generator to comply with all
federal, state, provincial and local laws and regulations. We recommend that you contact an
appropriate waste disposal contractor and environmental agency for relevant laws and
regulations. Under the U.S., Resource Conservation and Recovery Act (RCRA), it is the
responsibility of the user of the product to determine at the time of disposal, whether the
product meets relevant waste classification and to assure proper disposal.
Disposal methods Dispose of waste to licensed waste disposal site in accordance with the requirements of the
local Waste Disposal Authority.
14. Transport information
General Not regulated.
UN Number
This product is not dangerous to transport.
UN proper shipping name
This product is not dangerous to transport.
Transport hazard class(es)
This product is not dangerous to transport.
Packing group
This product is not dangerous to transport.
Environmental hazards
Environmentally Hazardous Substance
No.
Special precautions for user
This product is not dangerous to transport.
15. Regulatory information
US Federal Regulations
SARA Section 302 Extremely Hazardous Substances Tier II Threshold Planning Quantities
Not listed.
CERCLA/Superfund, Hazardous Substances/Reportable Quantities (EPA)
Not listed.
SARA Extremely Hazardous Substances EPCRA Reportable Quantities
Not listed.
SARA 313 Emission Reporting
Not listed
7/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
RCRA RCRA Information: Currently, the product is not listed in the federal hazardous waste
regulation 40 CFR, Part 261.33, paragraphs (E) or (F), ie. chemical products that are
considered hazardous if they become waste. State or local hazardous waste regulations may
also apply if they are different from the federal regulation. It is the responsibility of the user of
the product to determine at the time of disposal, whether the product meets relevant waste
classification and to assure proper disposal.
SARA (311/312) Hazard Categories
None.
US State Regulations
California Proposition 65 Carcinogens and Reproductive Toxins
This product contains no listed substances known to the State of California to cause cancer, birth
defects or other reproductive harm, at levels which would require a warning under the statute.
Inventories
US – TSCA
This product is an article as defined by TSCA and is not required to be listed in the TSCA inventory.
US – TSCA 12(b) Export Notification
Not listed.
16. Other information
Abbreviations and acronyms
used in the safety data sheet
ACGIH American Conference of Industrial Hygienists ATE Acute Toxicity Estimate CAS#
Chemical Abstracts Service Number CERCLA Comprehensive Environmental Response,
Compensation, and Liability Act DOT Department of Transportation EmS Emergency
Response Procedures for Ships Carrying Dangerous Goods EPA Environmental Protection
Agency GHS Global Harmonized System HMIS Hazardous Materials Identification System,
IATA International Air Transport Association ICAO International Civil Aviation Organization
IMDG International Maritime Dangerous Goods Kow Octanol-water partition coefficient LC50
Lethal concentration to 50% of a test population LD50 Lethal dose to 50% of a test population
n.o.s. Not otherwise specified OSHA Occupational Safety and Health Administration PBT
Persistent, Bioaccumulative and Toxic substance PNEC Predicted No Effect Concentration
PPE Personal Protection Equipment RCRA Resource Conservation and Recovery Act SADT
Self-accelerating decomposition temperature SARA Superfund Admendments and
Reauthorization Act STOT Specific Target Organ Toxicity (STOT) RE Repeated Exposure
(STOT) SE Single Exposure TSCA Toxic Substance Control Act UN United Nations VOC
Volatile Organic Compound WHMIS Workplace Hazardous Materials Information System
Issued by U.S.A. Product Stewardship department
Revision date 5/1/2015
Revision 0
Hazard statements in fullUSH01 May form combustible dust concentrations in air
ACA HMIS Health rating. Slight hazard. (1)
ACA HMIS Physical hazard
rating.
Normally stable. (0)
ACA HMIS Personal
protection rating.
F
ACA HMIS Flammability
rating.
Will not burn. (0)
8/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
Wherever such words or phrases as “hazardous,” “toxic,” “carcinogen,” etc. appear herein, they are used as a defined or
described under state employee right-to-know laws, Federal OSHA laws or the direct sources for these lawssuch as the
International Agency for Research on Cancer (IARC), the National Toxicology Program (NTP), etc. The use of such words or
phrases should not be taken to mean that we deem or imply any substance or exposure to be toxic, hazardous or otherwise
harmful. Any exposure can only be understood within the entire context of its occurrence, which includes such factors as the
substance’s characteristics as defined in the SDS, amount and duration of exposures, other chemicals present and
preexistingindividual differences in response to the exposure. The data provided in this SDS is based on the information
received from our raw material suppliers and other sources believed to be reliable. We are supplying you this data solely in
compliance with the Federal OSHA Hazard Communication Standard, 29 CFR 1910.1200 and the Federal and State laws as
described in Section 15: Regulatory Information. The information contained in this SDS is proprietary and confidential to
HexcelCorporation. This SDS and the information in it are not to be used for purposes other than compliance with the
Federal OSHA Hazard Communication Standard. If you have received this SDS from any other source than Hexcel
Corporation or its authorized agent, the information contained in it may have been modified from the original document and it
may not be the most current revision. Liability, if any, for use of this product is limited to the terms contained in our sale terms
and conditions. We do not in any way warrant (expressed or implied, including any implied warranty for merchantability or
fitness for a particular purpose) the data contained or the product described in this SDS. Additionally, we do not warrant that
the product will not infringe any patent or other proprietary or property rights of others.
9/9