by | Sep 27, 2025
SAFETY DATA SHEET
SDS Ref # BGF-046
Prepared: 1/27/2020
Revised: 6/23/2022
Page 1 of 6
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
Section 1: Identification
Chemical Product Name/Identifier: All styles of aramid fabric
Finish: 337, 618, 656, 861, scoured
CAS Number: 26125-61-1
Synonyms: p-Aramid
Recommended Use and Restrictions on Use: Woven textile product used for reinforcement in various
resin systems
Company Information: BGF Industries
230 Slayton Ave. Suite A-1
Danville, VA 24540
Telephone: 800-476-4845, 434-857-4400
Email: info@bgf.com
Website: http://www.bgf.com
Section 2: Hazards Identification
OSHA HCS Status: This product is not hazardous chemical, as defined by OSHA at 29 CFR 1910.1200.
The finished product has not been tested.
Relevant Route of Exposure/Target Organs: Dermal, Inhalation
OSHA/GHS Signal Word and Hazard Statements:
OSHA/GHS Classification and Pictograms:
OSHA/GHS Precautionary Statements:
Prevention
Avoid breathing fibers or dust. Use only outdoors or in a well-ventilated area. Keep containers tightly
closed.
Response
If inhaled: Remove victim to fresh air and keep comfortable for breathing. Call a poison
center/doctor/physician if you feel unwell.
If skin irritation occurs: Get medical advice/attention.
Storage
Store in a well-ventilated place. Store locked up. Keep container tightly closed.
Disposal
Dispose of contents/container in accordance with local/regional/national/international regulations.
GHS Hazard and Precautionary Statement Codes: See Section 16.
SAFETY DATA SHEET
SDS Ref # BGF-046
Prepared: 1/27/2020
Revised: 6/23/2022
Page 2 of 6
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
Section 3: Composition/Information on Ingredients
Chemical Product Name: Aramid fabric
Synonyms:
Component CAS # Max % by weight
Poly (terephthaloychloride/p-
phenylenediamine
26125-61-1 99.8
Textile sizing and lubricants Not assigned 0.5
Absorbed water Not assigned 1.5
Section 4: First-Aid Measures
Skin Contact: Flush with ample cool water followed by washing with mild soap to remove accumulated
fibers.
Eye Contact: Flush with flowing water for 15 minutes seek medical attention if necessary.
Inhalation: Move to fresh air.
Ingestion: Not likely to occur through normal use. Should ingestion occur, seek medical attention.
Most Important Symptoms/Effects: Direct skin contact with fibrous glass or its dust may cause
mechanical irritation and transitory dermatitis. Breathing of fibers or dust may cause
mechanical irritation of the mouth, nose, and throat.
Indication of Immediate Medical Attention and Special Treatment Needed: Get medical attention if
product comes into contact with skin or eyes, or if it is inhaled or ingested.
Section 5: Fire-Fighting Measures
Extinguishing Media: Water, dry powder, or foam (needed for packaging only).
Hazardous Combustion Products: Not applicable.
Protective Equipment: Firefighters should be equipped with self-contained breathing apparatus and turn
out gear.
Fire Fighting Procedures/Precautions: Aramid itself will not support combustion, but in a sustained fire,
proper protection against products of combustion from the fuel must be worn.
Section 6: Accidental Release Measures
Personal Precautions: A release of this product is not expected to pose risks to workers under normal
circumstances. If the material is involved in a fire, or if dusts are produced, no action shall be
taken involving any personal risk or without suitable training. Keep unnecessary and
unprotected personnel from entering. Put on appropriate personal protective equipment.
Protective Equipment: Wear protective gloves/eye protection/skin protection.
Methods/Materials for Containment and Cleaning Up: Dust or loose fibers can be vacuumed or swept
with the aid of a dust suppressant. Dispose of in accordance with all government regulations.
Do not discharge into waterways or sewer systems without proper authority.
SAFETY DATA SHEET
SDS Ref # BGF-046
Prepared: 1/27/2020
Revised: 6/23/2022
Page 3 of 6
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
Section 7: Handling and Storage
Precautions: This product should be handled under conditions of good industrial hygiene and in conformity
with any local regulations to avoid unnecessary exposure. Use in a well-ventilated area. Do
not breathe dust. Avoid contact with skin.
Storage: Store in a well-ventilated, dry location.
Section 8: Exposure Controls/Personal Protection
Exposure Limits: p-Aramid fibers as such are not subject to any exposure regulation.
Component OSHA/PEL ACGIH/TLV
Fibrous dust 5 mg/m
3
5 mg/m
3
* Dust may be produced during handling
a. DuPont s Acceptable Exposure Limit.
Engineering Controls: Normal area ventilation is sufficient in most cases to keep dust and fiber levels
below the AEL.
Personal Protection Measures/Equipment:
Skin Protection Barrier creams, gloves, and long sleeve loose fitting clothing may be required for
certain workers who have sensitive skin or contact dermatitis. Work clothing should be laundered
separately from other clothing before reuse.
Eye Protection Not normally required, but as a good safety work practice, eye protection such as
safety glasses/side shields or equivalent whenever use of the product releases airborne fibrous
aramid.
Respiratory Protection MSHA/NIOSH approved respiratory protection can be used.
Other Protection Observe good personal hygiene.
Section 9: Physical and Chemical Properties
Appearance (physical state, color, etc.): Solid, yellow
Odor: Odorless
Odor Threshold: None
pH: None
Melting Point/Freezing Point: Does not melt
Initial Boiling Point: Not applicable
Flash Point: Not applicable
Evaporation Rate: Not applicable
Flammability: Not applicable
Upper/Lower Flammability or Explosive Limits: Not applicable
Vapor Pressure: Not applicable
Vapor Density: Not applicable
SAFETY DATA SHEET
SDS Ref # BGF-046
Prepared: 1/27/2020
Revised: 6/23/2022
Page 4 of 6
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
Relative Density/Specific Gravity: 1.44 to 1.45 at 20 C (68 F)
Solubility: Insoluble
Partition Coefficient: Not known
Auto-ignition Temperature: Not known
Decomposition Temperature: >932 F (500 C)
Volatility: Not known
Viscosity: Not applicable
Section 10: Stability and Reactivity
Stability: Stable at ambient temperatures. Not self-reactive, water-reactive, or spontaneously combustible
Hazardous Reactions: Under normal conditions of storage and use, hazardous reactions will not occur.
Conditions to Avoid: Strong bases and acids will cause chemical decomposition. Temperatures over
932 F (500 C) will cause decomposition.
Incompatible Materials: Aromatic polyamides react with strong oxidizing agents. Over time, UV light will
cause a darkening of the fabric and adversely affect the strength.
Hazardous Decomposition Products: May produce carbon oxides, organic compounds of low molecular
weight and hydrogen cyanide in low concentration.
Hazardous Polymerization: Will not occur
Section 11: Toxicological Information
Relevant Route of Exposure/Target Organs: Dermal, Inhalation
Symptoms: Dust may cause irritation.
Delayed and Immediate Effects: Not known
Chronic Effects (Short and Long Term Exposure): Not known
Numerical Measures of Toxicity:
p-Aramid : Oral LD50 (rat): >7,500 mg/kg
Carcinogenicity: None of the ingredients present in this material at concentrations equal to or greater than
0.1% are listed by IARC, NTP, or OSHA, as a carcinogen.
Mutagenicity: No data available
Reproductive Toxicity: No data available
Section 12: Ecological Information
No data available
Section 13: Disposal Information
Do not discharge into waterways or sewer systems without proper authority. Dispose of in accordance with
all government regulations.
SAFETY DATA SHEET
SDS Ref # BGF-046
Prepared: 1/27/2020
Revised: 6/23/2022
Page 5 of 6
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
Section 14: Transport Information
Not regulated as a hazardous material/dangerous good for transportation in all modes of transportation (US
DOT, ICAO/IATA, IMO).
Section 15: Regulatory Information
TSCA Inventory Status: Exempt per section 8(a), 710.2(f), and 704.5(a)
SARA Title III Section 302: None
SARA Title III Section 304: None
SARA Title III Section 311/312 Hazard Categories: Immediate (acute)
SARA TITLE III Section 313: This product does not contain components that are subject to the reporting
requirements of Section 313 of the Emergency Planning and Community Right to Know Act of 1986
(EPCRA or SARA Title III) and 40 CFR 372.
CERCLA RQ: Not listed
California Proposition 65: None known
Massachusetts Right-To-Know: Less than reportable quantity
New Jersey Right-To-Know: Less than reportable quantity
Pennsylvania Right-To-Know: Less than reportable quantity
Canada: All components of this product are included on the Domestic Substances List (DSL) or are not
required to be listed on the Canadian DSL.
Europe: All components of this product are included on the European Inventory of Existing Commercial
Chemical Substances (EINECS) or are not required to be listed on the EINECS.
China: All components of this product are included on the Chinese Inventory (IECSC) or are not required
to be listed on the Chinese IECSC.
Japan: All components of this product are included on the Japanese (ENCS) inventory or are not required
to be listed on the Japanese inventory.
Korea: All components of this product are included on the Korean (ECL) inventory or are not required to be
listed on the Korean ECL.
Philippines: All components of this product are included on the Philippine (PICCS) or are not required to
be listed on the Philippine PICCS.
Australia: All components of this product are included on the Australian (AICS) or are not required to be
listed on the Australian AICS.
Section 16: Other Information
This product is classified as a Skin Irritant Category 3, however OSHA does not include Category 3
substances in its hazard classification system.
GHS Label Hazard Statement Codes
H316: Causes mild skin irritation
H335: May cause respiratory tract irritation.
GHS Label Precautionary Statement Codes
P261: Avoid breathing dusts or fibers.
P271: Use only outdoors or in well-ventilated area.
P304+P340: IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for
breathing.
P312: Call a POISON CENTER or doctor/physician if you feel unwell.
P332+P313: If skin irritation occurs: Get medical advice/attention.
P403+P233: Store in a well-ventilated place. Keep container tightly closed.
P501: Dispose of contents/container in accordance with local/regional/national/international regulations.
Abbreviations
ACGIH/TLV American Conference of Industrial Hygienists Threshold Limit Value
SAFETY DATA SHEET
SDS Ref # BGF-046
Prepared: 1/27/2020
Revised: 6/23/2022
Page 6 of 6
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
CAS Chemical Abstracts Service
CERCLA Comprehensive Environmental Response Compensation and Liability Act
CFR US Code of Federal Regulations
DOT US Department of Transportation
EPCRA Emergency Planning and Community Right to Know Act
GHS UN Globally Harmonized System of Classification and Labeling of Chemicals
HCS Hazard Communication Standard
IARC International Agency for Research on Cancer
ICAO/IATA International Civil Aviation Organization/International Air Transport Association
IMO/IMDG International Maritime Organization/International Maritime Dangerous Goods Code
LD50 Lethal dose to half of test animals
NTP National Toxicology Program
OSHA US Occupational Safety Health Administration
PEL Permissible exposure limit
RQ Reportable quantity
SARA Superfund Amendments and Reauthorization Act
SDS Safety data sheet
TSCA Toxic Substances Control Act
UN United Nations
US/USA United States
While this company believes that the data contained herein are factual and the opinions expressed are
based on tests and data believed to be reliable, it is the user’s responsibility to determine the safety,
toxicity, and suitability for his or her own use of the product described herein. Since the actual use by
others is beyond our control, no guarantee, expressed or implied, is made by this company as to the effects
of such use, the results to be obtained, or the safety and toxicity of the product, nor does this company
assume any liability arising out of use, by others, of the product referred to herein. Nor is the information
herein to be construed as absolutely complete since additional information may be necessary or desirable
when particular or exceptional conditions or circumstances exist or because of applicable laws or
governmental regulations.
by | Sep 27, 2025
SAFETY DATA SHEET
SDS Ref # BGF-046
Prepared: 1/27/2020
Revised: 6/23/2022
Page 1 of 6
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
Section 1: Identification
Chemical Product Name/Identifier: All styles of aramid fabric
Finish: 337, 618, 656, 861, scoured
CAS Number: 26125-61-1
Synonyms: p-Aramid
Recommended Use and Restrictions on Use: Woven textile product used for reinforcement in various
resin systems
Company Information: BGF Industries
230 Slayton Ave. Suite A-1
Danville, VA 24540
Telephone: 800-476-4845, 434-857-4400
Email: info@bgf.com
Website: http://www.bgf.com
Section 2: Hazards Identification
OSHA HCS Status: This product is not hazardous chemical, as defined by OSHA at 29 CFR 1910.1200.
The finished product has not been tested.
Relevant Route of Exposure/Target Organs: Dermal, Inhalation
OSHA/GHS Signal Word and Hazard Statements:
OSHA/GHS Classification and Pictograms:
OSHA/GHS Precautionary Statements:
Prevention
Avoid breathing fibers or dust. Use only outdoors or in a well-ventilated area. Keep containers tightly
closed.
Response
If inhaled: Remove victim to fresh air and keep comfortable for breathing. Call a poison
center/doctor/physician if you feel unwell.
If skin irritation occurs: Get medical advice/attention.
Storage
Store in a well-ventilated place. Store locked up. Keep container tightly closed.
Disposal
Dispose of contents/container in accordance with local/regional/national/international regulations.
GHS Hazard and Precautionary Statement Codes: See Section 16.
SAFETY DATA SHEET
SDS Ref # BGF-046
Prepared: 1/27/2020
Revised: 6/23/2022
Page 2 of 6
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
Section 3: Composition/Information on Ingredients
Chemical Product Name: Aramid fabric
Synonyms:
Component CAS # Max % by weight
Poly (terephthaloychloride/p-
phenylenediamine
26125-61-1 99.8
Textile sizing and lubricants Not assigned 0.5
Absorbed water Not assigned 1.5
Section 4: First-Aid Measures
Skin Contact: Flush with ample cool water followed by washing with mild soap to remove accumulated
fibers.
Eye Contact: Flush with flowing water for 15 minutes seek medical attention if necessary.
Inhalation: Move to fresh air.
Ingestion: Not likely to occur through normal use. Should ingestion occur, seek medical attention.
Most Important Symptoms/Effects: Direct skin contact with fibrous glass or its dust may cause
mechanical irritation and transitory dermatitis. Breathing of fibers or dust may cause
mechanical irritation of the mouth, nose, and throat.
Indication of Immediate Medical Attention and Special Treatment Needed: Get medical attention if
product comes into contact with skin or eyes, or if it is inhaled or ingested.
Section 5: Fire-Fighting Measures
Extinguishing Media: Water, dry powder, or foam (needed for packaging only).
Hazardous Combustion Products: Not applicable.
Protective Equipment: Firefighters should be equipped with self-contained breathing apparatus and turn
out gear.
Fire Fighting Procedures/Precautions: Aramid itself will not support combustion, but in a sustained fire,
proper protection against products of combustion from the fuel must be worn.
Section 6: Accidental Release Measures
Personal Precautions: A release of this product is not expected to pose risks to workers under normal
circumstances. If the material is involved in a fire, or if dusts are produced, no action shall be
taken involving any personal risk or without suitable training. Keep unnecessary and
unprotected personnel from entering. Put on appropriate personal protective equipment.
Protective Equipment: Wear protective gloves/eye protection/skin protection.
Methods/Materials for Containment and Cleaning Up: Dust or loose fibers can be vacuumed or swept
with the aid of a dust suppressant. Dispose of in accordance with all government regulations.
Do not discharge into waterways or sewer systems without proper authority.
SAFETY DATA SHEET
SDS Ref # BGF-046
Prepared: 1/27/2020
Revised: 6/23/2022
Page 3 of 6
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
Section 7: Handling and Storage
Precautions: This product should be handled under conditions of good industrial hygiene and in conformity
with any local regulations to avoid unnecessary exposure. Use in a well-ventilated area. Do
not breathe dust. Avoid contact with skin.
Storage: Store in a well-ventilated, dry location.
Section 8: Exposure Controls/Personal Protection
Exposure Limits: p-Aramid fibers as such are not subject to any exposure regulation.
Component OSHA/PEL ACGIH/TLV
Fibrous dust 5 mg/m
3
5 mg/m
3
* Dust may be produced during handling
a. DuPont s Acceptable Exposure Limit.
Engineering Controls: Normal area ventilation is sufficient in most cases to keep dust and fiber levels
below the AEL.
Personal Protection Measures/Equipment:
Skin Protection Barrier creams, gloves, and long sleeve loose fitting clothing may be required for
certain workers who have sensitive skin or contact dermatitis. Work clothing should be laundered
separately from other clothing before reuse.
Eye Protection Not normally required, but as a good safety work practice, eye protection such as
safety glasses/side shields or equivalent whenever use of the product releases airborne fibrous
aramid.
Respiratory Protection MSHA/NIOSH approved respiratory protection can be used.
Other Protection Observe good personal hygiene.
Section 9: Physical and Chemical Properties
Appearance (physical state, color, etc.): Solid, yellow
Odor: Odorless
Odor Threshold: None
pH: None
Melting Point/Freezing Point: Does not melt
Initial Boiling Point: Not applicable
Flash Point: Not applicable
Evaporation Rate: Not applicable
Flammability: Not applicable
Upper/Lower Flammability or Explosive Limits: Not applicable
Vapor Pressure: Not applicable
Vapor Density: Not applicable
SAFETY DATA SHEET
SDS Ref # BGF-046
Prepared: 1/27/2020
Revised: 6/23/2022
Page 4 of 6
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
Relative Density/Specific Gravity: 1.44 to 1.45 at 20 C (68 F)
Solubility: Insoluble
Partition Coefficient: Not known
Auto-ignition Temperature: Not known
Decomposition Temperature: >932 F (500 C)
Volatility: Not known
Viscosity: Not applicable
Section 10: Stability and Reactivity
Stability: Stable at ambient temperatures. Not self-reactive, water-reactive, or spontaneously combustible
Hazardous Reactions: Under normal conditions of storage and use, hazardous reactions will not occur.
Conditions to Avoid: Strong bases and acids will cause chemical decomposition. Temperatures over
932 F (500 C) will cause decomposition.
Incompatible Materials: Aromatic polyamides react with strong oxidizing agents. Over time, UV light will
cause a darkening of the fabric and adversely affect the strength.
Hazardous Decomposition Products: May produce carbon oxides, organic compounds of low molecular
weight and hydrogen cyanide in low concentration.
Hazardous Polymerization: Will not occur
Section 11: Toxicological Information
Relevant Route of Exposure/Target Organs: Dermal, Inhalation
Symptoms: Dust may cause irritation.
Delayed and Immediate Effects: Not known
Chronic Effects (Short and Long Term Exposure): Not known
Numerical Measures of Toxicity:
p-Aramid : Oral LD50 (rat): >7,500 mg/kg
Carcinogenicity: None of the ingredients present in this material at concentrations equal to or greater than
0.1% are listed by IARC, NTP, or OSHA, as a carcinogen.
Mutagenicity: No data available
Reproductive Toxicity: No data available
Section 12: Ecological Information
No data available
Section 13: Disposal Information
Do not discharge into waterways or sewer systems without proper authority. Dispose of in accordance with
all government regulations.
SAFETY DATA SHEET
SDS Ref # BGF-046
Prepared: 1/27/2020
Revised: 6/23/2022
Page 5 of 6
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
Section 14: Transport Information
Not regulated as a hazardous material/dangerous good for transportation in all modes of transportation (US
DOT, ICAO/IATA, IMO).
Section 15: Regulatory Information
TSCA Inventory Status: Exempt per section 8(a), 710.2(f), and 704.5(a)
SARA Title III Section 302: None
SARA Title III Section 304: None
SARA Title III Section 311/312 Hazard Categories: Immediate (acute)
SARA TITLE III Section 313: This product does not contain components that are subject to the reporting
requirements of Section 313 of the Emergency Planning and Community Right to Know Act of 1986
(EPCRA or SARA Title III) and 40 CFR 372.
CERCLA RQ: Not listed
California Proposition 65: None known
Massachusetts Right-To-Know: Less than reportable quantity
New Jersey Right-To-Know: Less than reportable quantity
Pennsylvania Right-To-Know: Less than reportable quantity
Canada: All components of this product are included on the Domestic Substances List (DSL) or are not
required to be listed on the Canadian DSL.
Europe: All components of this product are included on the European Inventory of Existing Commercial
Chemical Substances (EINECS) or are not required to be listed on the EINECS.
China: All components of this product are included on the Chinese Inventory (IECSC) or are not required
to be listed on the Chinese IECSC.
Japan: All components of this product are included on the Japanese (ENCS) inventory or are not required
to be listed on the Japanese inventory.
Korea: All components of this product are included on the Korean (ECL) inventory or are not required to be
listed on the Korean ECL.
Philippines: All components of this product are included on the Philippine (PICCS) or are not required to
be listed on the Philippine PICCS.
Australia: All components of this product are included on the Australian (AICS) or are not required to be
listed on the Australian AICS.
Section 16: Other Information
This product is classified as a Skin Irritant Category 3, however OSHA does not include Category 3
substances in its hazard classification system.
GHS Label Hazard Statement Codes
H316: Causes mild skin irritation
H335: May cause respiratory tract irritation.
GHS Label Precautionary Statement Codes
P261: Avoid breathing dusts or fibers.
P271: Use only outdoors or in well-ventilated area.
P304+P340: IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for
breathing.
P312: Call a POISON CENTER or doctor/physician if you feel unwell.
P332+P313: If skin irritation occurs: Get medical advice/attention.
P403+P233: Store in a well-ventilated place. Keep container tightly closed.
P501: Dispose of contents/container in accordance with local/regional/national/international regulations.
Abbreviations
ACGIH/TLV American Conference of Industrial Hygienists Threshold Limit Value
SAFETY DATA SHEET
SDS Ref # BGF-046
Prepared: 1/27/2020
Revised: 6/23/2022
Page 6 of 6
Inspired by Innovation :: Driven by Excellence
BGF INDUSTRIES, INC. 230 Slayton Ave Suite A-1 Danville, Virginia 24540 USA
434-857-4400 toll free: 800-476-4845
www. bgf.com info@bgf.com
CAS Chemical Abstracts Service
CERCLA Comprehensive Environmental Response Compensation and Liability Act
CFR US Code of Federal Regulations
DOT US Department of Transportation
EPCRA Emergency Planning and Community Right to Know Act
GHS UN Globally Harmonized System of Classification and Labeling of Chemicals
HCS Hazard Communication Standard
IARC International Agency for Research on Cancer
ICAO/IATA International Civil Aviation Organization/International Air Transport Association
IMO/IMDG International Maritime Organization/International Maritime Dangerous Goods Code
LD50 Lethal dose to half of test animals
NTP National Toxicology Program
OSHA US Occupational Safety Health Administration
PEL Permissible exposure limit
RQ Reportable quantity
SARA Superfund Amendments and Reauthorization Act
SDS Safety data sheet
TSCA Toxic Substances Control Act
UN United Nations
US/USA United States
While this company believes that the data contained herein are factual and the opinions expressed are
based on tests and data believed to be reliable, it is the user’s responsibility to determine the safety,
toxicity, and suitability for his or her own use of the product described herein. Since the actual use by
others is beyond our control, no guarantee, expressed or implied, is made by this company as to the effects
of such use, the results to be obtained, or the safety and toxicity of the product, nor does this company
assume any liability arising out of use, by others, of the product referred to herein. Nor is the information
herein to be construed as absolutely complete since additional information may be necessary or desirable
when particular or exceptional conditions or circumstances exist or because of applicable laws or
governmental regulations.
by | Sep 27, 2025
BGF-005BBbbbb
Page – 1 – of 7
SAFETY DATA SHEET
BGF-047
Date prepared: 5/31/2015
Section 1: Identification
Chemical Product Name/Identifier: All styles of aramid fabric
Finish: Greige. Loom-state, Unfinished
CAS Number: 26125-61-1
Synonyms: p-Aramid
Recommended Use and Restrictions on Use: Woven textile product used for reinforcement in various
resin systems
Company Information: BGF Industries
3802 Robert Porcher Way
Greensboro, NC 27410
Telephone: 800-476-4845, 336-545-0011
Email: info@bgf.com
Website: http://www.bgf.com
Section 2: Hazards Identification
OSHA HCS Status: This product is not hazardous chemical, as defined by OSHA at 29 CFR 1910.1200.
The finished product has not been tested.
Relevant Route of Exposure/Target Organs: Dermal, Inhalation
OSHA/GHS Signal Word and Hazard Statements:
OSHA/GHS Classification and Pictograms:
OSHA/GHS Precautionary Statements:
Prevention
Avoid breathing fibers or dust. Use only outdoors or in a well-ventilated area. Keep containers tightly
closed.
Response
If inhaled: Remove victim to fresh air and keep comfortable for breathing. Call a poison
center/doctor/physician if you feel unwell.
If skin irritation occurs: Get medical advice/attention.
Storage
Store in a well-ventilated place. Store locked up. Keep container tightly closed.
Disposal
Dispose of contents/container in accordance with local/regional/national/international regulations.
GHS Hazard and Precautionary Statement Codes: See Section 16.
BGF-005BBbbbb
Page – 2 – of 7
SAFETY DATA SHEET
BGF-047
Date prepared: 5/31/2015
Section 3: Composition/Information on Ingredients
Chemical Product Name: Aramid fabric
Synonyms: p-Aramid
Component CAS # Max % by weight
Poly (terephthaloychloride/p-
phenylenediamine
26125-61-1 98.5
Textile sizing and lubricants Not assigned 3.5
Absorbed water Not assigned 7
Section 4: First-Aid Measures
Skin Contact: Flush with ample cool water followed by washing with mild soap to remove accumulated
fibers.
Eye Contact: Flush with flowing water for 15 minutes seek medical attention if necessary.
Inhalation: Move to fresh air.
Ingestion: Not likely to occur through normal use. Should ingestion occur, seek medical attention.
Most Important Symptoms/Effects: Direct skin contact with fibers or its fibrous dust may cause
mechanical irritation and transitory dermatitis. Breathing of fibers or dust may cause
mechanical irritation of the mouth, nose, and throat.
Indication of Immediate Medical Attention and Special Treatment Needed: Get medical attention if
product comes into contact with skin or eyes, or if it is inhaled or ingested.
Section 5: Fire-Fighting Measures
Extinguishing Media: Water, dry powder, or foam (needed for packaging only).
Hazardous Combustion Products: Not applicable.
Protective Equipment: Firefighters should be equipped with self-contained breathing apparatus and turn
out gear.
Fire Fighting Procedures/Precautions: Aramid itself will not support combustion, but in a sustained fire,
proper protection against products of combustion from the fuel must be worn.
Section 6: Accidental Release Measures
Personal Precautions: A release of this product is not expected to pose risks to workers under normal
circumstances. If the material is involved in a fire, or if dusts are produced, no action shall be
taken involving any personal risk or without suitable training. Keep unnecessary and
unprotected personnel from entering. Put on appropriate personal protective equipment.
Protective Equipment: Wear protective gloves/eye protection/skin protection.
Methods/Materials for Containment and Cleaning Up: Dust or loose fibers can be vacuumed or swept
with the aid of a dust suppressant. Dispose of in accordance with all government regulations.
Do not discharge into waterways or sewer systems without proper authority.
BGF-005BBbbbb
Page – 3 – of 7
SAFETY DATA SHEET
BGF-047
Date prepared: 5/31/2015
Section 7: Handling and Storage
Precautions: This product should be handled under conditions of good industrial hygiene and in
conformity with any local regulations to avoid unnecessary exposure. Use in a well-ventilated
area. Do not breathe dust. Avoid contact with skin.
Storage: Store in a well-ventilated, dry location.
Section 8: Exposure Controls/Personal Protection
Exposure Limits: p-Aramid fibers as such are not subject to any exposure regulation.
Component AEL
a
AEL
a
Aramid dust/fibers* 2 RFP/cc (Respirable
Fibers)
5 mg/m
3
(Non-fibrous particulate
and/or non-respirable fibers)
* Dust may be produced during handling
a. DuPont s Acceptable Exposure Limit.
Engineering Controls: Normal area ventilation is sufficient in most cases to keep dust and fiber levels
below the AEL.
Personal Protection Measures/Equipment:
Skin Protection Barrier creams, gloves, and long sleeve loose fitting clothing may be required
for certain workers who have sensitive skin or contact dermatitis. Work clothing should be
laundered separately from other clothing before reuse.
Eye Protection Not normally required, but as a good safety work practice, eye protection such
as safety glasses/side shields or equivalent whenever use of the product releases airborne fibrous
aramid.
Respiratory Protection MSHA/NIOSH approved respiratory protection can be used.
Other Protection Observe good personal hygiene.
Section 9: Physical and Chemical Properties
Appearance (physical state, color, etc.): Solid, yellow
Odor: Odorless
Odor Threshold: None
pH: None
Melting Point/Freezing Point: Does not melt
Initial Boiling Point: Not applicable
Flash Point: Not applicable
Evaporation Rate: Not applicable
Flammability: Not applicable
Upper/Lower Flammability or Explosive Limits: Not applicable
BGF-005BBbbbb
Page – 4 – of 7
SAFETY DATA SHEET
BGF-047
Date prepared: 5/31/2015
Vapor Pressure: Not applicable
Vapor Density: Not applicable
Relative Density/Specific Gravity: 1.44 to 1.45 at 20 C (68 F)
Solubility: Insoluble
Partition Coefficient: Not known
Auto-ignition Temperature: Not known
Decomposition Temperature: >932 F (500 C)
Volatility: Not known
Viscosity: Not applicable
Section 10: Stability and Reactivity
Stability: Stable at ambient temperatures. Not self-reactive, water-reactive, or spontaneously
combustible
Hazardous Reactions: Under normal conditions of storage and use, hazardous reactions will not occur.
Conditions to Avoid: Strong bases and acids will cause chemical decomposition. Temperatures over
932 F (500 C) will cause decomposition.
Incompatible Materials: Aromatic polyamides react with strong oxidizing agents. Over time, UV light will
cause a darkening of the fabric and adversely affect the strength.
Hazardous Decomposition Products: May produce carbon oxides, organic compounds of low molecular
weight and hydrogen cyanide in low concentration.
Hazardous Polymerization: Will not occur under normal temperatures.
Section 11: Toxicological Information
Relevant Route of Exposure/Target Organs: Dermal, Inhalation
Symptoms: Dust may cause irritation.
Delayed and Immediate Effects: Not known
Chronic Effects (Short and Long Term Exposure): Not known
Numerical Measures of Toxicity:
p-Aramid : Oral LD50 (rat): >7,500 mg/kg
Carcinogenicity: None of the ingredients present in this material at concentrations equal to or greater
than 0.1% are listed by IARC, NTP, or OSHA, as a carcinogen.
Mutagenicity: No data available
Reproductive Toxicity: No data available
BGF-005BBbbbb
Page – 5 – of 7
SAFETY DATA SHEET
BGF-047
Date prepared: 5/31/2015
Section 12: Ecological Information
No data available
Section 13: Disposal Information
Do not discharge into waterways or sewer systems without proper authority. Dispose of in accordance
with all government regulations.
Section 14: Transport Information
Not regulated as a hazardous material/dangerous good for transportation in all modes of transportation
(US DOT, ICAO/IATA, IMO).
Section 15: Regulatory Information
TSCA Inventory Status: Exempt per section 8(a), 710.2(f), and 704.5(a)
SARA Title III Section 302: None
SARA Title III Section 304: None
SARA Title III Section 311/312 Hazard Categories: Immediate (acute)
SARA TITLE III Section 313: This product does not contain components that are subject to the reporting
requirements of Section 313 of the Emergency Planning and Community Right to Know Act of 1986
(EPCRA or SARA Title III) and 40 CFR 372.
CERCLA RQ: Not listed
California Proposition 65: None known
Massachusetts Right-To-Know: Less than reportable quantity
New Jersey Right-To-Know: Less than reportable quantity
Pennsylvania Right-To-Know: Less than reportable quantity
Canada: All components of this product are included on the Domestic Substances List (DSL) or are not
required to be listed on the Canadian DSL.
Europe: All components of this product are included on the European Inventory of Existing Commercial
Chemical Substances (EINECS) or are not required to be listed on the EINECS.
China: All components of this product are included on the Chinese Inventory (IECSC) or are not required
to be listed on the Chinese IECSC.
Japan: All components of this product are included on the Japanese (ENCS) inventory or are not
required to be listed on the Japanese inventory.
Korea: All components of this product are included on the Korean (ECL) inventory or are not required to
be listed on the Korean ECL.
Philippines: All components of this product are included on the Philippine (PICCS) or are not required to
be listed on the Philippine PICCS.
BGF-005BBbbbb
Page – 6 – of 7
SAFETY DATA SHEET
BGF-047
Date prepared: 5/31/2015
Australia: All components of this product are included on the Australian (AICS) or are not required to be
listed on the Australian AICS.
Section 16: Other Information
Date of Preparation or Revision: 5/31/2015
This product is classified as a Skin Irritant Category 3, however OSHA does not include Category 3
substances in its hazard classification system.
GHS Label Hazard Statement Codes
Signal Word: WARNING
H316: Causes mild skin irritation
H335: May cause respiratory tract irritation.
GHS Label Precautionary Statement Codes
P261: Avoid breathing dusts or fibers.
P271: Use only outdoors or in well-ventilated area.
P304+P340: IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for
breathing.
P312: Call a POISON CENTER or doctor/physician if you feel unwell.
P332+P313: If skin irritation occurs: Get medical advice/attention.
P403+P233: Store in a well-ventilated place. Keep container tightly closed.
P501: Dispose of contents/container in accordance with local/regional/national/international regulations.
Abbreviations
ACGIH/TLV American Conference of Industrial Hygienists Threshold Limit Value
CAS Chemical Abstracts Service
CERCLA Comprehensive Environmental Response Compensation and Liability Act
CFR US Code of Federal Regulations
DOT US Department of Transportation
EPCRA Emergency Planning and Community Right to Know Act
GHS UN Globally Harmonized System of Classification and Labeling of Chemicals
HCS Hazard Communication Standard
IARC International Agency for Research on Cancer
ICAO/IATA International Civil Aviation Organization/International Air Transport Association
IMO/IMDG International Maritime Organization/International Maritime Dangerous Goods Code
LD50 Lethal dose to half of test animals
BGF-005BBbbbb
Page – 7 – of 7
SAFETY DATA SHEET
BGF-047
Date prepared: 5/31/2015
NTP National Toxicology Program
OSHA US Occupational Safety Health Administration
PEL Permissible exposure limit
RQ Reportable quantity
SARA Superfund Amendments and Reauthorization Act
SDS Safety data sheet
TSCA Toxic Substances Control Act
UN United Nations
US/USA United States
While this company believes that the data contained herein are factual and the opinions expressed are
based on tests and data believed to be reliable, it is the user’s responsibility to determine the safety,
toxicity, and suitability for his or her own use of the product described herein. Since the actual use by
others is beyond our control, no guarantee, expressed or implied, is made by this company as to the
effects of such use, the results to be obtained, or the safety and toxicity of the product, nor does this
company assume any liability arising out of use, by others, of the product referred to herein. Nor is the
information herein to be construed as absolutely complete since additional information may be necessary
or desirable when particular or exceptional conditions or circumstances exist or because of applicable
laws or governmental regulations.
by | Sep 27, 2025
1218-04
12K Carbon
12K Carbon
506 GSM / 15 oz.
Plain
8 / in.
8 / in.
50″
Style #
Warp Yarn:
Fill Yarn:
Fabric Weight, Dry
WeaveStyle
Warp Count:
Fill Count:
Fabric Width
Fiber
Nominal Construction
Please Contact Us For Additional Information
Composite Fabrics of America
PO Box 609
105 Pierpoint Lane
Taylorsville, NC 28681
828-632-5220 Office
828-632-5464
www.cfamills.com
www.Textral.com
Made in the United States of America
by | Sep 27, 2025
Introduction:
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
Product name: Vectorply Aramid and Hybrid Fabrics
Synonyms: EC-BX, EC-BXM, EX-BXTR, EC-QX, EC-QXM, EC-LT, EC-LTM, EC-TTX, EC-TTXi EC-TTXTR, EC-TLX, EC-TLXN,
EC-TLXM, EC-TLXTR, EC-WV, K-BX, K-QX, K-WV, K-WM, KE-BX, KE-BXM, KE-TTX, KE-TTXM, KE-TTXCFM
KE-TTXA, KE-TLYM, KE-SXMM, KE-W, KE-WM, KE-WV, KE-QX, KE-LTM, KC-BX, KC-TTX, KCE-TLX, KEC-TTX
KEC-TTXi, KEC-TTXM, KEC- WX, KEC-BX, CKE-QXRR, CKES-QXRR, CEB-TLX, CE-LT, CE-LTM, CE-TXL,
CE-TLXA, CE-TTXR, EKC-QXR, EKCS-QXR, EK-TLX, EBC-QXM, ICE-QXR, KEC-QX, KE-LT
Supplier Name: Vectorply Corporation
Address: 3400 South Railroad Street
Phenix City, AL 36867 USA
www.vectorply.com
Company Phone Numbers: 1-800-577-4521 (US) Monday-Friday 8:00am – 5:00pm EST
01-334-291-7704 (Outside US) Monday-Friday 8:00am – 5:00pm EST
* Vectorply Corp. does not manufacture any of the component parts of the products covered by the Safe Use Instructions. This
document is a compilation of the safe use data furnished by these manufacturers. SDS or safe use information for component
parts can be made available upon request.
SECTION 2: HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW:
Appearance/Odor: Odorless, white, black, and/or yellow fabric with black or white polyester stitching.
WARNING!
MAY CAUSE SKIN IRRITATION
MAY CAUSE EYE IRRITATION
MAY CAUSE UPPER RESPIRATORY TRACT IRRITATION
MAY FORM COMBUSTIBLE DUST CONCENTRATIONS IN AIR
Potential Health Effects: See Section 11 for more information.
Likely Routes of Exposure:Eye contact, skin contact, Inhalation.
Inhalation: Irritation of the upper respiratory tract (scratchy throat), coughing, and congestion may occur in extreme exposures.
Ingestion: This product is not intended to be ingested (eaten). If ingested, it may cause temporary irritation to the
gastrointestinal (digestive) tract.
Skin: Temporary irritation (itching) or redness may occur.
Eyes: Temporary irritation (itching) or redness may occur.
Medical conditions aggravated
aggravated by exposure: Pre-existing chronic respiratory, skin, or eye diseases or conditions.
Regulatory Status: This material is not considered hazardous by the OSHA Hazard Communication Standard (29CFR 1910.1200)
Carcinogenicity: Not classified as a human carcinogen. As supplied, this product does not contain respirable glass fibers.
See section 11 for more information.
Environmental: Carbon fiber is electrically conductive and it can cause the short-circuiting of electrical equipment.
There is no known ecological information for this material, see Section 12 for more information.
SECTION 3: COMPOSITION / INFORMATION ON INGREDIENTS
Component: CAS # % by Wt.
Polyester Yarn 25038-59-9 0 – 5
Sizing Not Available 0 – 5
Carbon Fiber(Continuous filament, non respirable)7440-44-0 0-95
Aramid Fiber(Continuous filament, non respirable)26125-61-1 0-95
Glass Fiber(Continuous filament, non respirable)65997-17-3 0-95
Fiber Glass Veil(Continuous filament, non respirable)65997-17-3 0-15
Polyester Veil 25038-59-9 0-15
Copolyamide Veil Not Available 0-15
SECTION 4: FIRST AID MEASURES
Inhalation: Remove to fresh air. Seek medical attention if irritation persists. If not breathing, if breathing is irregular or if
respiratory arrest occurs, get medical attention, provide artificial respiration or oxygen by trained personnel.
Ingestion: Ingestion of this product is unlikely. If swallowed, rinse mouth with water (only if person is conscious).
Get medical attention immediately if irritation develops and persists.
Skin Contact: Immediately flush skin with plenty of water. Remove contaminated clothing and shoes. Get medical attention
if irritation develops and persists. Wash clothing before reuse.
Eye Contact: Immediately flush eyes with plenty of water for at least 15 minutes. If easy to do, remove contact lenses, if worn.
Get medical attention immediately if irritation persists.
Revision: 4
Date:8/18/2019
Page:1 of 4
Safe Use Instructions – Aramid and Hybrid Fabrics
This document is provided to ensure safe handling and use instructions for Vectorply aramid and hybrid glass, carbon and aramid products.
Continuous aramid, glass and carbon fibers are defined as “articles” under REACH and are not regulated by either OSHA Hazard Communication
Standard , 29 CFR 1910.1200 or Canada Hazardous Products Regulation SOR/2015-17 (WHMIS 2015). An SDS is not required for manufacturing
articles.
SECTION 5: FIRE FIGHTING MEASURES
Suitable Extinguishing Media:Dry chemical, foam, carbon dioxide (CO2), water fog.
Unsuitable Extinguishing Media:Full water jet.
Products of Combustion: Carbon monoxide, Nitrogen oxides, carbon dioxide, hydrogen, other undetermined compounds could be released
in small quantities.
Protection of Firefighters:Firefighters should wear self-contained breathing apparatus (SCBA) and full fire-fighting turnout gear.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Personal precautions: Use personal protection recommended in Section 8.
Environmental Precautions: No special precautions are needed in case of a release or spill.
Methods for Containment: This material will settle out of air. Prevent from spreading by covering, diking, or other means.
Methods for Clean-up: This material will settle out of air. Pick up large pieces, carefully sweep or vacuum remaining
material and place in suitable container. Avoid generating dust.
Other Information: Dispose of as solid waste in accordance with local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
Handling: Use appropriate personal protective equipment (See Section 8). Avoid dust generation.
Avoid contact with skin and eyes. Do not breathe dust. Do not swallow.
In the supplied form the product is not explosive at all, however the buildup of fine dust can lead to
a risk of dust explosions. Keep away from sources of ignition – refrain from smoking.
Storage: Do not store together with oxidizing agents.
Store in accordance with local, state, and federal regulations. Keep product in its packaging
to avoid dust generation. Store at or below 25
o
C (77
o
F) and relative humidity less than 65%
for optimum peroformance.
SECTION 8: EXPOSURE CONTROL / PERSONNEL PROTECTION
Exposure Limits: TLV-TWA: 10mg/m3 Total dust, 3 mg/m3 respirable (ACGIH)
Carbon Fiber: PEL-TWA: 15 mg/m3 total dust, 5 mg/m3 respirable (OSHA)
Fiber Glass: TLV-TWA: 1 f/cc, 10mg/m3 Total dust, 3 mg/m3 respirable (ACGIH)
PEL-TWA: 15 mg/m3 total dust, 5 mg/m3 respirable (OSHA)
TWAEV: 1 f/cc respirable, 5 mg/m3 inhalable (Ontario Canada)
TWA: 10 mg/m3 (Mexico)
Aramid Fiber: TLV-TWA: 10mg/m3 Total dust, 3 mg/m3 respirable (ACGIH)
PEL-TWA: 15 mg/m3 total dust, 5 mg/m3 respirable (OSHA)
Polyester / Copolyamide: Not Available
Engineering Controls: Use local/general exhaust ventilation as required to keep airborne concentrations below exposure limits.
Eye/face Protection: Safety glasses with side-shields.
Skin Protection: Long pants, long sleeved shirt, and protective gloves.
Respiratory Protection: Respiratory protection must be used If ventilation is not available or inadequate to keep dust
and fiber levels below exposure levels listed in section 8. A NIOSH approved disposable N95 type
dust repirator or better is recommended.
General Hygiene Considerations: Wash hands immediately after handlind product and before breaks. Wash contaminate clothes
thoroughly before reuse.
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Appearance: Black, white, yellow fabric with black or white polyester stitching with or without polyester or glass veil.
Odor: Odorless
Odor Threshold: N/A
Physical State: Solid
pH: Not available
Melting Point: 3500
o
C (Carbon), >800
o
C (Glass), carbonizes at ~427
o
C (Aramid), 250-300
o
C (Polyester)
Initial Boiling Point and Boiling Range:Not available
Flash Point: Not available
Evaporation Rate: Not available
Flammability: Not available
Flammability or Explosive Limits: Not Available
Vapor Pressure: Not Available
Specific Gravity: 1.7 – 1.9 (Carbon), 2.60 (Glass), 1.45 (Aramid), 1.68 (Polyester) (Ref: water = 1.00)
Solubility: Insoluble
Partition Coefficient: Not Available
Autoignition Temperature: Not Available
Decomposition Temperature: Carbon begins to oxidize at temperatures >240
o
C in a standard environment.
Electrical Conductivity: Yes
SECTION 10: STABILITY AND REACTIVITY
Stability: Stable under normal conditions.
Conditions to Avoid: Avoid contact with strong oxidizing agents. Accumulation of fine dust may entail the risk of of dust
explosion in the presence of air.
Incompatible Materials: Strong oxydizers.
Hazardous Decomposition Products: Under normal conditions of storage and use, hazardous decomposition products should not be produced.
Possibility of Hazardous Reactions: Reactions with strong oxydizers may occur.
Revision: 4
Date:8/18/2019
Page:2 of 4
Safe Use Instructions – Aramid and Hybrid Fabrics
SECTION 11: TOXICOLOGICAL INFORMATION
Summary: There are no known health effects from the long term use or contact with carbon or aramid fibers.
There are no known health effects from the long term use or contact with nonrespirable continuous
filament glass fibers. As manufactured, the glass fibers in this product are nonrespirable.
Continuous filament glass fibers that are chopped, crushed, or severely mechanically processed
during manufacturing or use may contain a very small amount of respirable particulate, some of which
may be glass shards.The measured airborne concentration of these respirable fibers in areas where
severe processing of fiberglass occurred has been shown to be extreemly low nad well below the TLV.
Based on animal study, repeated or prolonged exposure to respirable glass fibers may cause fibrosis,
lung cancer, and mesolthelioma.
SECTION 12: ECOLOGICAL INFORMATION
Environmental Effects: This material is not expected to cause harm to animals, plants or fish.
Other Adverse Effects: No known significant effects or critical hazards.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal: If this product, as supplied, becomes a waste, it does not meet the criteria of a hazardous waste
as defined under the Resource Conservation and Recovery Act (RCRA) 40 CFR 261.
Dispose of as solid waste in accordance with local, state, and federal regulations.
SECTION 14: TRANSPORT INFORMATION
Transport Regulations: This product is not classified as dangerous goods according to international transport regulations.
SECTION 15: REGULATORY INFORMATION
Global Inventories All components listed or exempted
TSCA*: United States All components listed or exempted
DSL: Canada All components listed or exempted
KECI: Korea All components listed or exempted
PICCS: Philippines All components listed or exempted
ENCS: Japan All components listed or exempted
AICS: Australia All components listed or exempted
IECSC: China All components listed or exempted
REACH: European Union All components listed or exempted
*The product covered in the safe use instructions is an article and therefore is exempt from listing on the national chemical inventories in particular
on the US EPA Toxic Substances Control Act (TSCA).
United States
SARA 302/304/311/312 extremely hazardous substances: No products were found.
SARA 302/304 emergency planning and notification: No products were found.
SARA 302/304/311/312 hazardous chemicals: No products were found.
CERCLA Hazardous substances: No products were found.
SARA 311/312 MSDS Distribution – Chemical Inventory – Hazard Identification:
Chemical Name CAS# Acute Chronic FireReactivePressure
Carbon Fiber 7440-44-0 Y N Y Y N
Fiber Glass 65997-17-3 Y Y N N N
Aramid Fiber 26125-61-1 Y N N N N
Product as-supplied Y Y N N N
Canada
WHMIS (Canada) None identified.
SECTION 16: ADDITIONAL INFORMATION
HMIS Health Hazard 1
HMIS Flammability Hazard 0
HMIS Reactivity: 0
HMIS Personal Protection: X
Revision: 4
Date:8/18/2019
Page:3 of 4
Safe Use Instructions – Aramid and Hybrid Fabrics
Disclaimer: Vectorply Corp. does not manufacture any of the component parts of the products covered by the
safe use instructions. This document is a compilation of the safe use data furnished by these
manufacturers. SDS or safe use information for component parts can be made available upon request.
The information and data contained in this document are presented in good faith and believed to be
reliable. Nothing herein shall be deemed to constitute a warranty, expressed or implied, that said
information or data are correct or that the products described are merchantable or fit for a particular
purpose, or that said information, data, or products can be used without infringing patents of third
parties.
Revision: 4
Date:8/18/2019
Page:4 of 4
Safe Use Instructions – Aramid and Hybrid Fabrics
Rev Change Date Author
0Original Release 5/25/2017T. Williams
1Removed MSDS and pictogram reference 11/30/2017J. Woodrow
2Update address 2/1/2018J. Woodrow
3Update to French and Spanish 2/1/2018J. Woodrow
4Add EBC-QXM, ICE-QXR, KEC-QX, KE-LT 8/18/2019J. Woodrow
by | Sep 27, 2025
Revision date: 5/1/2015 Revision: 0
SAFETY DATA SHEET
HexForce F3 and F16 Finish
1. Identification
Product identifier
Product name HexForce F3 and F16 Finish
Product number 20871US-2
Synonyms; trade names Applicable to: E Glass or S Glass with a Chromium (CR3+) Methacrylate Finish applied
Details of the supplier of the safety data sheet
Supplier Hexcel Reinforcements
1913 N. King Street
Seguin
TX 78155
USA
Tel: ++ 830 379 1580
Fax: ++ 830 379 9544
Contact Person 11711 Dublin Blvd, Dublin, California, USA. ++925 551 4900
Emergency telephone number
Emergency telephone To be used only for advice on chemical emergencies, spillages, fires or First Aid:
For emergencies in US/Canada: CHEMTREC 800 424 9300
For emergencies in rest of the world: CARECHEM24 – +44 (0) 1235 239 670
2. Hazard(s) identification
Classification of the substance or mixture
OSHA Regulatory Status This Product is Not Hazardous under the OSHA Hazard Communication Standard.
Physical hazards Combustible Dust – USH01
Health hazards Not Classified
Environmental hazards Not Classified
Label elements
Signal word Warning
Hazard statements USH01 May form combustible dust concentrations in air
Other hazards
Warning! May cause temporary mechanical irritation of the eyes, skin or upper respiratory tract. The American Conference of
Governmental Industrial Hygienists (ACGIH) lists under synthetic vitreous fiber; continous filament glass fibers: 1 f/cc
(respirable) and 5 mg/m3 (inhalable). Warning! Dust generated from machining, grinding or sanding the product may be
combustible and could result in fire and/or explosion should the necessary dust concentration in air and ignition source be
present.
Hazards not otherwise
classified (HNOC)
Fine dust clouds may form explosive mixtures with air.
1/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
3. Composition/information on ingredients
Mixtures
Composition comments Continuous filament glass fiber (type E, R, D, S2) of silicon, aluminum, calcium, boron and
magnesium oxides in a vitreous amorphous state. Filament diameter r>3um CAS 65997-17-
3: >99% w/w
4. First-aid measures
Description of first aid measures
Inhalation With any sign of respiratory distress, affected persons should be taken into fresh air and made
to rest while medical attention is sought.
Ingestion If fiber from the product is ingested, immediately rinse mouth repeatedly with water. If
swallowing has occurred, do not induce vomiting. If requested, give affected person sips of
water. Seek medical attention.
Skin Contact In case of contact with the product or the cured product dust or particulates, immediately wash
skin with mild soap and water. Use a washcloth to help remove fibers. To avoid further
irritation, do not scratch irritated areas. Rubbing or scratching may force the fibers into the
skin. Get medical attention immediately if the irritation persists.
Eye contact contamination by fiber should be removed by flushing with water for at least 15 minutes. Seek
medical attention if irritation persists.
Most important symptoms and effects, both acute and delayed
General information Filaments are mechanical irritants and may induce temporary mouth, nose and throat
irritation. Skin or eye contact may cause itching and temporary irritation. Ingestion may cause
temporary mechanical irritation of the digestive tract. Pre-existing conditions such as
respiratory or skin disorders may be aggravated by exposure to the product or dust/particulate
generated from machining/grinding of the cured product.
Indication of immediate medical attention and special treatment needed
Notes for the doctor No specific recommendations. If in doubt, get medical attention promptly.
5.Fire-fighting measures
Extinguishing media
Suitable extinguishing mediaExtinguish with foam, carbon dioxide, dry powder or water fog.
Unsuitable extinguishing
media
Do not use water jet as an extinguisher, as this will spread the fire.
Special hazards arising from the substance or mixture
Specific hazards No unusual fire or explosion hazards noted.
Hazardous combustion
products
In an emergency situation leading to elevated temperature, there may be release of toxic
gases and vapours. The products of combustion and decomposition will depend on other
materials present in the fire and the actual conditions of the fire.
Advice for firefighters
Special protective equipment
for firefighters
Wear positive-pressure self-contained breathing apparatus (SCBA) and appropriate protective
clothing.
6. Accidental release measures
Personal precautions, protective equipment and emergency procedures
Personal precautions Avoid contact with skin, eyes or clothing.
2/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
Environmental precautions
Environmental precautionsDue to the physical nature of this product, environmental release to drains and water courses
is not possible.
3/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
Methods and material for containment and cleaning up
Methods for cleaning up Clean up material and put into a suitable container and dispose of properly (See Section 13).
Reference to other sectionsFor personal protection, see Section 8. Collect and dispose of spillage as indicated in Section
13.
7. Handling and storage
Precautions for safe handling
Usage precautions Storage: Keep container tightly closed and dry.
Conditions for safe storage, including any incompatibilities
Storage precautions Store in tightly-closed, original container. Keep container dry.
Specific end uses(s)
Specific end use(s) As this product is an article, this section is not applicable.
8. Exposure Controls/personal protection
Control parameters
Occupational exposure limits
Long-term exposure limit (8-hour TWA): 1 f/cc 5 mg/m3 continuous filament glass fibers
Exposure controls
Protective equipment
Appropriate engineering
controls
Provide adequate ventilation.
Eye/face protection Eyewear complying with an approved standard should be worn if a risk assessment indicates
eye contact is possible.
Hand protection It is recommended that gloves are made of the following material: Polyvinyl chloride (PVC).
Rubber (natural, latex).
Other skin and body
protection
Wear appropriate clothing to prevent any possibility of skin contact.
Hygiene measures Wash hands at the end of each work shift and before eating, smoking and using the toilet.
Respiratory protection Wear a suitable dust mask.
4/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
9. Physical and Chemical Properties
Information on basic physical and chemical properties
Appearance White fibers woven into fabrics of varying weight, width and thickness, depending on the style,
with a finish applied.
Color White.
Odor No characteristic odor.
Odor threshold Not relevant due to the physical form of this product.
pH Not relevant due to the physical form of this product.
Melting point 700C / 1292F C
Initial boiling point and rangeNot relevant due to the physical form of this product.
Flash point Not relevant due to the physical form of this product.
Evaporation rate Not relevant due to the physical form of this product.
Evaporation factor Not relevant due to the physical form of this product.
Upper/lower flammability or
explosive limits
Not relevant due to the physical form of this product.
Vapour pressure Not relevant due to the physical form of this product.
Vapour density Not relevant due to the physical form of this product.
Relative density Not relevant due to the physical form of this product.
Solubility(ies) Not relevant due to the physical form of this product.
Auto-ignition temperatureNot relevant due to the physical form of this product.
Viscosity Not relevant due to the physical form of this product.
Explosive properties The mixture does not meet the criteria for explosive in accordance with GHS.
Explosive under the influence
of a flame
The mixture does not meet the criteria for explosive in accordance with GHS.
Oxidising properties Does not meet the criteria for classification as oxidizing.
Comments The indicated values do not necessarily correspond to the product specification. Please refer
to the technical data sheet for specification data.
5/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
10. Stability and reactivity
Stability Stable at normal ambient temperatures and when used as recommended.
Possibility of hazardous
reactions
Not relevant.
Conditions to avoid Avoid heat, flames and other sources of ignition.
Materials to avoid No specific material or group of materials is likely to react with the product to produce a
hazardous situation.
Hazardous decomposition
products
Does not decompose when used and stored as recommended. In an emergency situation
leading to elevated temperature, there may be release of toxic gases and vapors. The
products of combustion and decompostion will depend on other materials present in the fire
and the actual conditions of the fire.
11. Toxicological information
Information on toxicological effects
Toxicological effects Continuous filament fiber is listed by the International Agency for Research on Cancer (IARC)
as a group 3 (not classifiable as a human carcinogen).
Carcinogenicity
IARC carcinogenicity IARC Group 3 Not classifiable as to its carcinogenicity to humans.
Inhalation May cause respiratory system irritation.
Ingestion None expected under normal conditions of use. Ingestion is not an expected route of industrial
exposure.
Skin Contact Contact may cause mechanical irritation, skin redness, itching and drying of the skin.
Prolonged or repeated contact may cause allergic skin reaction, dermatitis and possible
sensitization.
Eye contact May cause mechanical irritation.
Medical considerations Preexisting eye, skin or respiratory disorders may be aggravated by exposure to this product.
12. Ecological Information
Ecotoxicity No ecological data has been determined on the total product.
Toxicity
Toxicity Not regarded as dangerous for the environment.
Persistance and degradability
Persistence and degradabilityNot relevant due to the physical form of this product.
Bioaccumulative potential
Bio-Accumulative PotentialNot relevant due to the physical form of this product.
Mobility in soil
Mobility Not relevant due to the physical form of this product.
6/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
13. Disposal considerations
Waste treatment methods
General information Materials for disposal should be placed in appropriate sealed containers to avoid potential
human and environmental exposure. It is the responsibility of the generator to comply with all
federal, state, provincial and local laws and regulations. We recommend that you contact an
appropriate waste disposal contractor and environmental agency for relevant laws and
regulations. Under the U.S., Resource Conservation and Recovery Act (RCRA), it is the
responsibility of the user of the product to determine at the time of disposal, whether the
product meets relevant waste classification and to assure proper disposal.
Disposal methods Dispose of waste to licensed waste disposal site in accordance with the requirements of the
local Waste Disposal Authority.
14. Transport information
General Not regulated.
UN Number
This product is not dangerous to transport.
UN proper shipping name
This product is not dangerous to transport.
Transport hazard class(es)
This product is not dangerous to transport.
Packing group
This product is not dangerous to transport.
Environmental hazards
Environmentally Hazardous Substance
No.
Special precautions for user
This product is not dangerous to transport.
15. Regulatory information
US Federal Regulations
SARA Section 302 Extremely Hazardous Substances Tier II Threshold Planning Quantities
Not listed.
CERCLA/Superfund, Hazardous Substances/Reportable Quantities (EPA)
Not listed.
SARA Extremely Hazardous Substances EPCRA Reportable Quantities
Not listed.
SARA 313 Emission Reporting
Not listed
7/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
RCRA RCRA Information: Currently, the product is not listed in the federal hazardous waste
regulation 40 CFR, Part 261.33, paragraphs (E) or (F), ie. chemical products that are
considered hazardous if they become waste. State or local hazardous waste regulations may
also apply if they are different from the federal regulation. It is the responsibility of the user of
the product to determine at the time of disposal, whether the product meets relevant waste
classification and to assure proper disposal.
SARA (311/312) Hazard Categories
None.
US State Regulations
California Proposition 65 Carcinogens and Reproductive Toxins
This product contains no listed substances known to the State of California to cause cancer, birth
defects or other reproductive harm, at levels which would require a warning under the statute.
Inventories
US – TSCA
This product is an article as defined by TSCA and is not required to be listed in the TSCA inventory.
US – TSCA 12(b) Export Notification
Not listed.
16. Other information
Abbreviations and acronyms
used in the safety data sheet
ACGIH American Conference of Industrial Hygienists ATE Acute Toxicity Estimate CAS#
Chemical Abstracts Service Number CERCLA Comprehensive Environmental Response,
Compensation, and Liability Act DOT Department of Transportation EmS Emergency
Response Procedures for Ships Carrying Dangerous Goods EPA Environmental Protection
Agency GHS Global Harmonized System HMIS Hazardous Materials Identification System,
IATA International Air Transport Association ICAO International Civil Aviation Organization
IMDG International Maritime Dangerous Goods Kow Octanol-water partition coefficient LC50
Lethal concentration to 50% of a test population LD50 Lethal dose to 50% of a test population
n.o.s. Not otherwise specified OSHA Occupational Safety and Health Administration PBT
Persistent, Bioaccumulative and Toxic substance PNEC Predicted No Effect Concentration
PPE Personal Protection Equipment RCRA Resource Conservation and Recovery Act SADT
Self-accelerating decomposition temperature SARA Superfund Admendments and
Reauthorization Act STOT Specific Target Organ Toxicity (STOT) RE Repeated Exposure
(STOT) SE Single Exposure TSCA Toxic Substance Control Act UN United Nations VOC
Volatile Organic Compound WHMIS Workplace Hazardous Materials Information System
Issued by U.S.A. Product Stewardship department
Revision date 5/1/2015
Revision 0
Hazard statements in fullUSH01 May form combustible dust concentrations in air
ACA HMIS Health rating. Slight hazard. (1)
ACA HMIS Physical hazard
rating.
Normally stable. (0)
ACA HMIS Personal
protection rating.
F
ACA HMIS Flammability
rating.
Will not burn. (0)
8/9
Revision date: 5/1/2015 Revision: 0
HexForce F3 and F16 Finish
Wherever such words or phrases as “hazardous,” “toxic,” “carcinogen,” etc. appear herein, they are used as a defined or
described under state employee right-to-know laws, Federal OSHA laws or the direct sources for these lawssuch as the
International Agency for Research on Cancer (IARC), the National Toxicology Program (NTP), etc. The use of such words or
phrases should not be taken to mean that we deem or imply any substance or exposure to be toxic, hazardous or otherwise
harmful. Any exposure can only be understood within the entire context of its occurrence, which includes such factors as the
substance’s characteristics as defined in the SDS, amount and duration of exposures, other chemicals present and
preexistingindividual differences in response to the exposure. The data provided in this SDS is based on the information
received from our raw material suppliers and other sources believed to be reliable. We are supplying you this data solely in
compliance with the Federal OSHA Hazard Communication Standard, 29 CFR 1910.1200 and the Federal and State laws as
described in Section 15: Regulatory Information. The information contained in this SDS is proprietary and confidential to
HexcelCorporation. This SDS and the information in it are not to be used for purposes other than compliance with the
Federal OSHA Hazard Communication Standard. If you have received this SDS from any other source than Hexcel
Corporation or its authorized agent, the information contained in it may have been modified from the original document and it
may not be the most current revision. Liability, if any, for use of this product is limited to the terms contained in our sale terms
and conditions. We do not in any way warrant (expressed or implied, including any implied warranty for merchantability or
fitness for a particular purpose) the data contained or the product described in this SDS. Additionally, we do not warrant that
the product will not infringe any patent or other proprietary or property rights of others.
9/9
by | Sep 27, 2025
by | Sep 27, 2025
by | Sep 27, 2025
by | Sep 27, 2025
MATERIAL SAFETY DATA SHEET (MSDS)
METYX
Carbon Non-Crimp Stitched Fabrics
1/4
FR-04-2/13.04.2015
1.Identification of the Substance and Company/Undertaking
1.1.Trade Name: METYX
Carbon Non-Crimp Stitched Fabrics
1.2.Chemical Name: Carbon fiber (PAN based)
1.3.Scope: Reinforcement for plastics
1.4.Supplier Details:
Telateks A.S. METYX Composites
Orhanl M. G ls m S. No:14 34956 Tuzla-Istanbul/TURKEY
Tel.: +90 216 394 32 60
Fax: +90 216 394 32 58
Web: www.metyx.com
e-Mail: metyx@metyx.com
Emergency Phone number: +90 216 394 32 60
2. Composition/Informat on on Ingredients
Continuous filament Carbon fiber including synthetic threading yarn
CAS No.
Content %
Carbon fiber 7440-44-0 > 98
Partially cured polymeric resin
Registered <2
Continuous filament Carbon fiber is a carbon product which is given a specific shape (filament) and dimension
(filament diameter). A surface treatment (sizing) is applied to the filament. The sizing is a mixture of chemicals,
i.e. film former, coupling agent and polymeric resin. The sizing content is usually less than or equal to 2%. Non
crimp fabrics made with Carbon fibers are stitched with synthetic yarns.
3. Hazards Identifications
This product including its components is not considered to be hazardous in the sense of the Directive 67/548/EEC
and Directive 1999/45/EC. Under normal industrial conditions, product is not flammable and has stability.
3.1.Skin: Directly contact with skin may cause irritation, itching, rash, swelling. Wear protective clothes.
3.2.Eye: May cause eye irritation, rash, pain. These symptoms may continue after stop working. This condition
may be temporary but may cause permanent influence as cornea. Wear safety glasses.
3.3.Respiratory: May cause respiratory problems. This may damage throat and lungs and cause cough. Wear
respiratory mask.
3.4.Hazards that do not directly lead to a classification: Carbon fiber is an electricity conducting material, it may
break up into fine particles. Finely dispersed carbon fiber may irritate skin, eyes and mucous membranes. Carbon
fiber dust may cause electrical short-circuits when contacted to electrical devices.
MATERIAL SAFETY DATA SHEET (MSDS)
METYX
Carbon Non-Crimp Stitched Fabrics
2/4
FR-04-2/13.04.2015
4. First Aid Measures
4.1. Inhalation: May cause respiratory problem. Move to fresh air. If symptoms persist, call physician.
4.2. Skin Contact: If skin irritation does occur, remove contaminated clothing and wash off plenty of water min.
15 minutes without rubbing. Use a mild soap if possible. If symptoms persist, call physician.
4.3. Eye Contact: In case of dust, thoroughly rinse eyes with clean water for at least 15 minutes. Arrange for
transport to the nearest medical facility for examination and treatment by a physician as soon as possible.
Remove contact lenses if any before continuing to rinse. Do not let the victim rub his eyes.
4.4. Ingestion: Gently wipe or rinse the inside of the mouth with water. Give water to the victim if conscious, but
do not make him vomit. In case of vomiting, do not let the victim swallow the vomit. Do not give anything to
ingest to unconscious or convulsing victim.
4.5. Additional information: Mild hydrocortisone skin cream is helpful for skin irritation.
5. Fire Fighting Measures
5.1. Suitable Extinguishing Media: Use foam, dry powder, carbon dioxide or water-mist.
5.2. Special Protective Clothing: In case of big fires self-contained breathing apparatus must be used ad full
protective clothing must be worn.
5.3. Additional information: Only the packaging film, polyester yarn and carbon sizing material are likely burn.
Combustion gases are basically carbon dioxide and water vapor. There may be small quantities of carbon
monoxide and other substances which make it necessary to use protective devices in the event of a major fire.
Emission of toxic gases: nitrogen oxide, carbon monoxide. When the product is burnt, fine carbon fiber particles
may be produced. They may cause electrical short-circuits when contacted to electrical devices.
6. Accidental Release Measures
6.1. Personal Precautions: Provide eyewash stations. Under normal industrial conditions, this product is not
flammable and has stability. (See chapter 8.) Precautions when handling dispersed substances: Because fine
particles may be dispersed, it is advised to wear a dust mark with P3 type filter.
6.2. Environmental Precautions: No special environmental precautions required.
6.3. Spill Cleanup Methods: Fiber dusts can cause to short circuit. Spreading has to eliminate.
7. Handling & Storage
7.1. Usage Precautions:
*Material to be handled with care: Do not cut the carbon fiber unnecessarily. Electricity conducting material, do
not allow contact with electric current sources.
*Avoid the dispersion of loose fibers: Handle the fiber in well ventilated premises (the ventilation devices should
have a filter to avoid discharging loose fibere into open air) where there are no electrical appliances or said
appliances are protected in sealed or pressurised cases
*Insulating varnish may be applied to electronic boards and electrical terminals.
MATERIAL SAFETY DATA SHEET (MSDS)
METYX
Carbon Non-Crimp Stitched Fabrics
3/4
FR-04-2/13.04.2015
*Advise for use and incompatibility with other materials: Avoid friction which may create loose and flying debris
7.2. Storage Precautions: Storage conditions do not have an influence on the product properties, but it is advised
to store the product in a clean and dry place, away from dust, in its original packaging. Packing material must be
prevented to damage during transporting and carrying.
7.3. Special Usage: The person contacted with carbon has to isolate or clean his hands before working with
electronic device. Vacuum clean, sweep or shovel carefully in order to prevent dust suspension.
8. Exposure Control & Personal Protection
If dust is created and ventilation is inadequate, it is advised to wear a dust mask, eye protection, gloves and clean
and dry work attire.
8.1. Engineering Measures: NA
8.2. Respiratory Equipment: Use protection mask with P3 type filter in case of dispersion of dust.
8.3. Skin Protect: always wear protective gloves conform to EN 374-1/2/3 and EN 420 when handling the
product.
8.4. Eye Protect: wear protective goggles or dustproof goggles.
8.5. Hygiene Considerations: Use vacuum cleaning for clothing and working area. Wash separately clothes.
Wash your hands before eating and using toilet.
9. Physical & Chemical Specifications
9.1.Appear./Form/Odour: Solid, black, roll, odourless
9.2.Density: aprx. 1,6-2,0 g/cm
9.3.pH : not applicable
9.4.Viscosity: not applicable
9.5.Solubility: insoluble in water and oil. Sizing agent soluble in chlorinated solvents, acetone, DMF
9.6. Vapour Pressure: not applicable
9.7. Flash Point: not applicable
9.8. Ignition Temp.: not applicable
9.9.Melting Point: not applicable
9.10. Boiling Temp.: not applicable
9.11. Explosion Limits: not applicable
9.12. Thermal Decomposition: not applicable, see chapter 10
10. Stability & Reactivity
10.1. Conditions to Avoid: Excess heat. Vigorous hardening may release toxic gases and create dangerous
decomposition products.
10.2. Materials to Avoid: Oxidizing agents, strong acids and bases
10.3. Hazardous Decomposition Products: Emission of nitrogen oxides and carbon monoxide.
MATERIAL SAFETY DATA SHEET (MSDS)
METYX
Carbon Non-Crimp Stitched Fabrics
4/4
FR-04-2/13.04.2015
11. Toxicological Information
Exposure risks:
Ingestion: Possible irritation of throat.
Inhalation: Possible irritation of respiratory apparatus.
Skin contact: May cause irritations.
Contact with eyes: May cause irritations.
12. Ecological Information
12.1 Ecotoxicity: Environmental exposure from substances of this preparation is limited due to the physical form
of the product.
12.2 Mobilite:
12.3 Stability &Decomposition:
12.4 Bioaccumulatetive:
12.5 Other: Carbon fiber is an electricity conducting material. It may cause short-circuits on contact with
electrical devices, especially when loose fibers are dispersed in the area.
13. Disposal Considerations
This product can be considered as immobile solid waste and disposed as solid waste. Carbon fiber must be
destroyed depending on local regulations. EWC (European Waste Catalogue) chapter 160306 belongs to Carbon
fiber materials.
If Carbon fiber involves any resin to form a composite structure (cured or half cured), disposing of this material
must do considering disposal consideration of the resin.
14.Transport Information: Not classified as dangerous in the meaning of transport regulations.
15.Regulatory Information
This product is not hazardous according to European Directive 99/45/EC, 67/548/EEC and their latest
amendment.
16.Other Information
DISCLAIMER
The information provided in this Safety Data Sheet is correct to the best of our knowledge, information and
belief at the date of its publication. The information given is designed only as guidance for safe handling, use,
processing, storage, transportation, disposal and release and is not to be considered a warranty or quality
specification. The information relates only to the specific material designated and may not be valid for such
material used in combination with any other materials or in any process, unless specified in the text. Users
assume full responsibility for applying the appropriate safety measures when the product used.
