17D3302679_SDS.pdf

by | Sep 27, 2025

SAFETY DATA SHEET

DOWSIL TB/TL/CER Sealant Clear

Version
3.0
Revision Date:
10/16/2017
SDS Number:
1291572-00010
Date of last issue: 04/24/2017
Date of first issue: 02/10/2015

1 / 11
SECTION 1. IDENTIFICATION
Product name

: DOWSIL TB/TL/CER Sealant Clear

Product code

: 04045036

Manufacturer or supplier’s details
Company Identification

: THE DOW CHEMICAL COMPANY
2030 WILLARD H DOW CENTER
MIDLAND MI 48674-0000
UNITED STATES

Telephone

: 800-258-2436

24-Hour Emergency Contact

: Chemtrec +1 800-424-9300

Local Emergency Number

: 800-424-9300

E-mail address : SDSQuestion@dow.com
Recommended use of the chemical and restrictions on use
Recommended use

: Adhesive, binding agents

SECTION 2. HAZARDS IDENTIFICATION
GHS classification in accordance with 29 CFR 1910.1200
Not a hazardous substance or mixture.
GHS label elements
Not a hazardous substance or mixture.
Precautionary Statements

:
Prevention:
P271 Use only outdoors or in a well-ventilated area.

Other hazards
None known.
SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS
Substance / Mixture

: Mixture
Chemical nature

: Silicone elastomer

Hazardous ingredients
Chemical name CAS-No. Concentration (% w/w)
Silicon dioxide 7631-86-9 >= 8 – <= 9 SECTION 4. FIRST AID MEASURES SAFETY DATA SHEET DOWSIL TB/TL/CER Sealant Clear Version 3.0 Revision Date: 10/16/2017 SDS Number: 1291572-00010 Date of last issue: 04/24/2017 Date of first issue: 02/10/2015 2 / 11 If inhaled : If inhaled, remove to fresh air. Get medical attention if symptoms occur. In case of skin contact : Wash with water and soap as a precaution. Get medical attention if symptoms occur. In case of eye contact : Flush eyes with water as a precaution. Get medical attention if irritation develops and persists. If swallowed : If swallowed, DO NOT induce vomiting. Get medical attention if symptoms occur. Rinse mouth thoroughly with water. Most important symptoms and effects, both acute and delayed : None known. Protection of first-aiders : No special precautions are necessary for first aid responders. Notes to physician : Treat symptomatically and supportively. SECTION 5. FIRE-FIGHTING MEASURES Suitable extinguishing media : Water spray Alcohol-resistant foam Carbon dioxide (CO2) Dry chemical Unsuitable extinguishing media : None known. Specific hazards during fire fighting : Exposure to combustion products may be a hazard to health. Hazardous combustion prod- ucts : Carbon oxides Silicon oxides Formaldehyde Specific extinguishing meth- ods : Use extinguishing measures that are appropriate to local cir- cumstances and the surrounding environment. Use water spray to cool unopened containers. Remove undamaged containers from fire area if it is safe to do so. Evacuate area. Special protective equipment for fire-fighters : Wear self-contained breathing apparatus for firefighting if necessary. Use personal protective equipment. SECTION 6. ACCIDENTAL RELEASE MEASURES Personal precautions, protec- tive equipment and emer- : Follow safe handling advice and personal protective equipment recommendations. SAFETY DATA SHEET DOWSIL TB/TL/CER Sealant Clear Version 3.0 Revision Date: 10/16/2017 SDS Number: 1291572-00010 Date of last issue: 04/24/2017 Date of first issue: 02/10/2015 3 / 11 gency procedures Environmental precautions : Discharge into the environment must be avoided. Prevent further leakage or spillage if safe to do so. Retain and dispose of contaminated wash water. Local authorities should be advised if significant spillages cannot be contained. Methods and materials for containment and cleaning up : Soak up with inert absorbent material. For large spills, provide diking or other appropriate containment to keep material from spreading. If diked material can be pumped, store recovered material in appropriate container. Clean up remaining materials from spill with suitable absorbent. Local or national regulations may apply to releases and disposal of this material, as well as those materials and items employed in the cleanup of releases. You will need to determine which regulations are applicable. Sections 13 and 15 of this SDS provide information regarding certain local or national requirements. SECTION 7. HANDLING AND STORAGE Technical measures : See Engineering measures under EXPOSURE CONTROLS/PERSONAL PROTECTION section. Local/Total ventilation : Use only with adequate ventilation. Advice on safe handling : Handle in accordance with good industrial hygiene and safety practice. Take care to prevent spills, waste and minimize release to the environment. Conditions for safe storage : Keep in properly labeled containers. Store in accordance with the particular national regulations. Materials to avoid : Do not store with the following product types: Strong oxidizing agents SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION Ingredients with workplace control parameters Ingredients CAS-No. Value type (Form of exposure) Control parame- ters / Permissible concentration Basis Silicon dioxide 7631-86-9 TWA (Dust) 20 Million particles per cubic foot (Silica) OSHA Z-3 TWA (Dust) 80 mg/m3 / %SiO2 OSHA Z-3 SAFETY DATA SHEET DOWSIL TB/TL/CER Sealant Clear Version 3.0 Revision Date: 10/16/2017 SDS Number: 1291572-00010 Date of last issue: 04/24/2017 Date of first issue: 02/10/2015 4 / 11 (Silica) TWA 6 mg/m (Silica) NIOSH REL These substance(s) are inextricably bound in the product and therefore do not contribute to a dust inhalation hazard. Silicon dioxide Engineering measures : Processing may form hazardous compounds (see section 10). Ensure adequate ventilation, especially in confined areas. Minimize workplace exposure concentrations. Personal protective equipment Respiratory protection : No personal respiratory protective equipment normally required. Hand protection Remarks : Wash hands before breaks and at the end of workday. Eye protection : Wear the following personal protective equipment: Safety glasses Skin and body protection : Skin should be washed after contact. Hygiene measures : Ensure that eye flushing systems and safety showers are located close to the working place. When using do not eat, drink or smoke. Wash contaminated clothing before re-use. These precautions are for room temperature handling. Use at elevated temperature or aerosol/spray applications may require added precautions. SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance : paste Color : colorless Odor : Acetic acid Odor Threshold : No data available pH : Not applicable Melting point/freezing point : No data available Initial boiling point and boiling range : Not applicable Flash point : Not applicable SAFETY DATA SHEET DOWSIL TB/TL/CER Sealant Clear Version 3.0 Revision Date: 10/16/2017 SDS Number: 1291572-00010 Date of last issue: 04/24/2017 Date of first issue: 02/10/2015 5 / 11 Evaporation rate : Not applicable Flammability (solid, gas) : Not classified as a flammability hazard Self-ignition : The substance or mixture is not classified as pyrophoric. The substance or mixture is not classified as self heating. Upper explosion limit / Upper flammability limit : No data available Lower explosion limit / Lower flammability limit : No data available Vapor pressure : Not applicable Relative vapor density : No data available Relative density : 1.04 Solubility(ies) Water solubility : No data available Partition coefficient: n- octanol/water : No data available Autoignition temperature : No data available Decomposition temperature : No data available Viscosity Viscosity, dynamic : Not applicable Explosive properties : Not explosive Oxidizing properties : The substance or mixture is not classified as oxidizing. Molecular weight : No data available Particle size : No data available SECTION 10. STABILITY AND REACTIVITY Reactivity : Not classified as a reactivity hazard. Chemical stability : Stable under normal conditions. Possibility of hazardous reac- tions : Use at elevated temperatures may form highly hazardous compounds. Can react with strong oxidizing agents. Acetic acid is formed upon contact with water or humid air. Hazardous decomposition products will be formed at elevated temperatures. SAFETY DATA SHEET DOWSIL TB/TL/CER Sealant Clear Version 3.0 Revision Date: 10/16/2017 SDS Number: 1291572-00010 Date of last issue: 04/24/2017 Date of first issue: 02/10/2015 6 / 11 Conditions to avoid : None known. Incompatible materials : Oxidizing agents Hazardous decomposition products Thermal decomposition : Formaldehyde SECTION 11. TOXICOLOGICAL INFORMATION Information on likely routes of exposure Skin contact Ingestion Eye contact Acute toxicity Not classified based on available information. Ingredients: Silicon dioxide: Acute oral toxicity : LD50 (Rat): > 3,300 mg/kg
Assessment: The substance or mixture has no acute oral tox-
icity
Remarks: Information taken from reference works and the
literature.

Acute inhalation toxicity

: LC50 (Rat): > 2.08 mg/l
Exposure time: 4 h
Test atmosphere: dust/mist
Assessment: The substance or mixture has no acute inhala-
tion toxicity
Remarks: Information taken from reference works and the
literature.

Acute dermal toxicity

: LD50 (Rabbit): > 5,000 mg/kg
Assessment: The substance or mixture has no acute dermal
toxicity
Remarks: Information taken from reference works and the
literature.

Skin corrosion/irritation
Not classified based on available information.
Ingredients:
Silicon dioxide:
Result: No skin irritation
Remarks: Information taken from reference works and the literature.

Serious eye damage/eye irritation
Not classified based on available information.

SAFETY DATA SHEET

DOWSIL TB/TL/CER Sealant Clear

Version
3.0
Revision Date:
10/16/2017
SDS Number:
1291572-00010
Date of last issue: 04/24/2017
Date of first issue: 02/10/2015

7 / 11
Ingredients:
Silicon dioxide:
Result: No eye irritation
Remarks: Information taken from reference works and the literature.

Respiratory or skin sensitization
Skin sensitization
Not classified based on available information.
Respiratory sensitization
Not classified based on available information.
Ingredients:
Silicon dioxide:
Assessment: Does not cause skin sensitization.

Test Type: Skin: test type not specified
Species: Guinea pig
Result: negative
Remarks: Information taken from reference works and the literature.

Germ cell mutagenicity
Not classified based on available information.
Ingredients:
Silicon dioxide:
Genotoxicity in vitro

: Result: negative
Remarks: Information taken from reference works and the
literature.

Genotoxicity in vivo

: Application Route: Ingestion
Result: negative
Remarks: Information taken from reference works and the
literature.

Germ cell mutagenicity –
Assessment

: Animal testing did not show any mutagenic effects.

Carcinogenicity
Not classified based on available information.
IARC

No ingredient of this product present at levels greater than or
equal to 0.1% is identified as probable, possible or confirmed
human carcinogen by IARC.

OSHA

No component of this product present at levels greater than or
equal to 0.1% is on OSHA s list of regulated carcinogens.

NTP

No ingredient of this product present at levels greater than or
equal to 0.1% is identified as a known or anticipated carcinogen
by NTP.

SAFETY DATA SHEET

DOWSIL TB/TL/CER Sealant Clear

Version
3.0
Revision Date:
10/16/2017
SDS Number:
1291572-00010
Date of last issue: 04/24/2017
Date of first issue: 02/10/2015

8 / 11

Reproductive toxicity
Not classified based on available information.
STOT-single exposure
Not classified based on available information.
STOT-repeated exposure
Not classified based on available information.
Aspiration toxicity
Not classified based on available information.
SECTION 12. ECOLOGICAL INFORMATION
Ecotoxicity
No data available
Persistence and degradability
No data available
Bioaccumulative potential
No data available
Mobility in soil
No data available
Other adverse effects
No data available
SECTION 13. DISPOSAL CONSIDERATIONS
Disposal methods
Resource Conservation and
Recovery Act (RCRA)
: This product has been evaluated for RCRA characteristics
and does not meet the criteria of hazardous waste if discarded
in its purchased form.

Waste from residues : Dispose of in accordance with local regulations.

Contaminated packaging : Empty containers should be taken to an approved waste
handling site for recycling or disposal.
If not otherwise specified: Dispose of as unused product.

SECTION 14. TRANSPORT INFORMATION
International Regulations
UNRTDG
Not regulated as a dangerous good
IATA-DGR
Not regulated as a dangerous good
IMDG-Code

SAFETY DATA SHEET

DOWSIL TB/TL/CER Sealant Clear

Version
3.0
Revision Date:
10/16/2017
SDS Number:
1291572-00010
Date of last issue: 04/24/2017
Date of first issue: 02/10/2015

9 / 11
Not regulated as a dangerous good
Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
Not applicable for product as supplied.
Domestic regulation
49 CFR
Not regulated as a dangerous good
SECTION 15. REGULATORY INFORMATION
EPCRA – Emergency Planning and Community Right-to-Know
CERCLA Reportable Quantity
Ingredients CAS-No. Component RQ
(lbs)
Calculated product RQ
(lbs)
Acetic acid 64-19-7 5000 *
Acetic anhydride 108-24-7 5000 *
*: Calculated RQ exceeds reasonably attainable upper limit.
SARA 304 Extremely Hazardous Substances Reportable Quantity
This material does not contain any components with a section 304 EHS RQ.
SARA 302 Extremely Hazardous Substances Threshold Planning Quantity
This material does not contain any components with a section 302 EHS TPQ.
SARA 311/312 Hazards

: No SARA Hazards

SARA 313

: This material does not contain any chemical components with
known CAS numbers that exceed the threshold (De Minimis)
reporting levels established by SARA Title III, Section 313.

US State Regulations
Pennsylvania Right To Know
Dimethyl siloxane, hydroxy-terminated 70131-67-8
Silicon dioxide 7631-86-9
Acetic acid 64-19-7
Acetic anhydride 108-24-7
California Prop. 65
This product does not contain any chemicals known to the State of California to cause cancer,
birth, or any other reproductive defects.
California Permissible Exposure Limits for Chemical Contaminants
Silicon dioxide 7631-86-9
The ingredients of this product are reported in the following inventories:
NZIoC

: All ingredients listed or exempt.

AICS

: All ingredients listed or exempt.

IECSC

: All ingredients listed or exempt.

PICCS : All ingredients listed or exempt.

SAFETY DATA SHEET

DOWSIL TB/TL/CER Sealant Clear

Version
3.0
Revision Date:
10/16/2017
SDS Number:
1291572-00010
Date of last issue: 04/24/2017
Date of first issue: 02/10/2015

10 / 11

DSL

: All chemical substances in this product comply with the CEPA
1999 and NSNR and are on or exempt from listing on the
Canadian Domestic Substances List (DSL).

REACH

: For purchases from Dow Chemical EU legal entities, all
ingredients are currently pre/registered or exempt under
REACH. Please refer to section 1 for recommended uses. For
purchases from non-EU Dow Chemical legal entities with the
intention to export into EEA please contact your DC
representative/local office.

TSCA

: All chemical substances in this product are either listed on the
TSCA Inventory or are in compliance with a TSCA Inventory
exemption.

TCSI

: All ingredients listed or exempt.

SECTION 16. OTHER INFORMATION
Further information
NFPA: HMIS IV:

HMIS ratings are based on a 0-4 rating
scale, with 0 representing minimal ha-
zards or risks, and 4 representing signifi-
cant hazards or risks. The “*” represents
a chronic hazard, while the “/” represents
the absence of a chronic hazard.

Full text of other abbreviations
NIOSH REL : USA. NIOSH Recommended Exposure Limits
OSHA Z-3 : USA. Occupational Exposure Limits (OSHA) – Table Z-3 Min-
eral Dusts
NIOSH REL / TWA : Time-weighted average concentration for up to a 10-hour
workday during a 40-hour workweek
OSHA Z-3 / TWA : 8-hour time weighted average

AICS – Australian Inventory of Chemical Substances; ASTM – American Society for the Testing of
Materials; bw – Body weight; CERCLA – Comprehensive Environmental Response, Compensation,
and Liability Act; CMR – Carcinogen, Mutagen or Reproductive Toxicant; DIN – Standard of the
German Institute for Standardisation; DOT – Department of Transportation; DSL – Domestic Sub-
stances List (Canada); ECx – Concentration associated with x% response; EHS – Extremely Ha-

Flammability

Health

Instability

0
1
0

Special hazard.
FLAMMABILITY
1
PHYSICAL HAZARD
HEALTH
0

/ 0

SAFETY DATA SHEET

DOWSIL TB/TL/CER Sealant Clear

Version
3.0
Revision Date:
10/16/2017
SDS Number:
1291572-00010
Date of last issue: 04/24/2017
Date of first issue: 02/10/2015

11 / 11
zardous Substance; ELx – Loading rate associated with x% response; EmS – Emergency Sche-
dule; ENCS – Existing and New Chemical Substances (Japan); ErCx – Concentration associated
with x% growth rate response; ERG – Emergency Response Guide; GHS – Globally Harmonized
System; GLP – Good Laboratory Practice; HMIS – Hazardous Materials Identification System;
IARC – International Agency for Research on Cancer; IATA – International Air Transport Associa-
tion; IBC – International Code for the Construction and Equipment of Ships carrying Dangerous
Chemicals in Bulk; IC50 – Half maximal inhibitory concentration; ICAO – International Civil Avia-
tion Organization; IECSC – Inventory of Existing Chemical Substances in China; IMDG – Interna-
tional Maritime Dangerous Goods; IMO – International Maritime Organization; ISHL – Industrial
Safety and Health Law (Japan); ISO – International Organisation for Standardization; KECI – Ko-
rea Existing Chemicals Inventory; LC50 – Lethal Concentration to 50 % of a test population; LD50
– Lethal Dose to 50% of a test population (Median Lethal Dose); MARPOL – International Conven-
tion for the Prevention of Pollution from Ships; MSHA – Mine Safety and Health Administration;
n.o.s. – Not Otherwise Specified; NFPA – National Fire Protection Association; NO(A)EC – No Ob-
served (Adverse) Effect Concentration; NO(A)EL – No Observed (Adverse) Effect Level; NOELR –
No Observable Effect Loading Rate; NTP – National Toxicology Program; NZIoC – New Zealand
Inventory of Chemicals; OECD – Organization for Economic Co-operation and Development;
OPPTS – Office of Chemical Safety and Pollution Prevention; PBT – Persistent, Bioaccumulative
and Toxic substance; PICCS – Philippines Inventory of Chemicals and Chemical Substances;
(Q)SAR – (Quantitative) Structure Activity Relationship; RCRA – Resource Conservation and Re-
covery Act; REACH – Regulation (EC) No 1907/2006 of the European Parliament and of the
Council concerning the Registration, Evaluation, Authorisation and Restriction of Chemicals; RQ –
Reportable Quantity; SADT – Self-Accelerating Decomposition Temperature; SARA – Superfund
Amendments and Reauthorization Act; SDS – Safety Data Sheet; TCSI – Taiwan Chemical Sub-
stance Inventory; TSCA – Toxic Substances Control Act (United States); UN – United Nations;
UNRTDG – United Nations Recommendations on the Transport of Dangerous Goods; vPvB –
Very Persistent and Very Bioaccumulative

Sources of key data used to
compile the Material Safety
Data Sheet
: Internal technical data, data from raw material SDSs, OECD
eChem Portal search results and European Chemicals Agen-
cy, http://echa.europa.eu/

Revision Date : 10/16/2017

Items where changes have been made to the previous version are highlighted in the body of this
document by two vertical lines.

The information provided in this Safety Data Sheet is correct to the best of our knowledge,
information and belief at the date of its publication. The information is designed only as a
guidance for safe handling, use, processing, storage, transportation, disposal and release and
shall not be considered a warranty or quality specification of any type. The information provided
relates only to the specific material identified at the top of this SDS and may not be valid when the
SDS material is used in combination with any other materials or in any process, unless specified
in the text. Material users should review the information and recommendations in the specific
context of their intended manner of handling, use, processing and storage, including an
assessment of the appropriateness of the SDS material in the user s end product, if applicable.

US / Z8

17CHA95_SDS.pdf

by | Sep 27, 2025

INDEX

17CHA95
17CHA95-G
17CHA95-Q

SAFETY DATA SHEET
Date Issued : 11/5/2013
MSDS No : CHALLENGE 95
CHALLENGE 95
1. PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: CHALLENGE 95
GENERAL USE: Release agent
MANUFACTURER 24 HR. EMERGENCY TELEPHONE NUMBERS
BJB Enterprises, Inc.
14791 Franklin Avenue
Tustin, CA 92780
Customer Service Number: (714) 734-8450
Fax: (714) 734-8929

CHEMTREC (US Transportation): (800) 424-9300
or (703) 527-3887 CCN# 2820
2. HAZARDS IDENTIFICATION
GHS CLASSIFICATIONS
Health:
Skin Irritation, Category 2
Eye Irritation, Category 2A
Mutagenicity, Category 1
Carcinogenicity, Category 1
Reproductive Toxicity, Category 2
Target Organ Toxicity (Single exposure), Category 3
Target Organ Toxicity (Repeated exposure), Category 2
Aspiration Hazard, Category 1
Environmental:
Chronic Hazards to the Aquatic Environment, Category 3
Physical:
Flammable Liquids, Category 2
GHS LABEL
Flame Exclamation
mark
Health hazard
SIGNAL WORD: DANGER
HAZARD STATEMENTS
H225: Highly flammable liquid and vapour.
H315: Causes skin irritation.
H319: Causes serious eye irritation.
H340: May cause genetic defects .
H350: May cause cancer .
H361: Suspected of damaging fertility or the unborn child .
H336: May cause drowsiness or dizziness.
H373: May cause damage to organs through prolonged or repeated exposure .
Page 1 of 8

H304: May be fatal if swallowed and enters airways.
H412: Harmful to aquatic life with long lasting effects.
PRECAUTIONARY STATEMENT(S)
Prevention:
P210: Keep away from heat/sparks/open flames/hot surfaces. No smoking.
P233: Keep container tightly closed.
P240: Ground/bond container and receiving equipment.
P241: Use explosion-proof electrical/ventilating/lighting/ / equipment.
P242: Use only non-sparking tools.
P243: Take precautionary measures against static discharge.
P201: Obtain special instructions before use.
P202: Do not handle until all safety precautions have been read and understood.
P260: Do not breathe dust/fume/gas/mist/vapours/spray.
P271: Use only outdoors or in a well-ventilated area.
P280: Wear protective gloves/protective clothing/eye protection/face protection.
P264: Wash thoroughly after handling.
P273: Avoid release to the environment.
Response:
P303+P361+P353: IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower.
P370+P378: In case of fire: Use for extinction.
P302+P352: IF ON SKIN: Wash with plenty of soap and water.
P321: Specific treatment (see on this label).
P332+P313: If skin irritation occurs: Get medical advice/attention.
P362: Take off contaminated clothing and wash before reuse.
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.
Continue rinsing.
P337+P313: If eye irritation persists: Get medical advice/attention.
P308+P313: IF exposed or concerned: Get medical advice/attention.
P304+P340: IF INHALED: Remove to fresh air and keep at rest in a position comfortable for breathing.
P312: Call a POISON CENTER or doctor/physician if you feel unwell.
P301+P310: IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.
P331: Do NOT induce vomiting.
Storage:
P403+P233: Store in a well-ventilated place. Keep container tightly closed.
P235: Keep cool.
P405: Store locked up.
Disposal:
P501: Dispose of contents/container in accordance with local/regional/national/international regulations.
EMERGENCY OVERVIEW
PHYSICAL APPEARANCE AND ODOR: Yellow liquid with a solvent odor.
IMMEDIATE CONCERNS: Warning! Flammable liquid and vapor. Harmful if swallowed. DO NOT induce vomiting if swallowed.
Harmful if inhaled. Causes serious eye irritation. Causes skin irritation. Keep away from heat, sparks, and flames. Vapors can travel to a
source of ignition and flash back.
POTENTIAL HEALTH EFFECTS
EYES: Causes serious eye irritation.
SKIN: Causes skin irritation. Frequent or prolonged contact may defat and dry the skin, leading to discomfort and dermatitis.
INGESTION: Harmful if swallowed. Aspiration hazard. This material can enter the lungs during swallowing or vomiting and cause lung
inflammation and damage. It may also cause irritation to the mucous membranes of the mouth, throat, and digestive tract.
INHALATION: Harmful if inhaled. Irritating to respiratory system. Prolonged inhalation my be harmful.
REPRODUCTIVE TOXICITY
REPRODUCTIVE EFFECTS: This product contains ingredients that are considered to cause reproductive harm.
CARCINOGENICITY: This product contains ingredients that are considered to be probable or suspected human carcinogens.
Page 2 of 8
CHALLENGE 95

MEDICAL CONDITIONS AGGRAVATED: Pre-existing eye, skin, and respiratory conditions may be aggravated by exposure.
ROUTES OF ENTRY: Eye and skin contact, inhalation of vapors, or accidental ingestion.
TARGET ORGANS: Contains material which may cause damage to the following organs: respiratory tract, kidneys, liver, central nervous
system (CNS).
3. COMPOSITION / INFORMATION ON INGREDIENTS
Chemical Name Wt.% CAS
Toluene 40 – 80108-88-3
2-propanol 0 – 20 67-63-0
1,2,4-trimethylbenzene 5 – 10 95-63-6
Stoddard solvent 5 – 108052-41-3
4. FIRST AID MEASURES
EYES: Immediately rinse with water. Remove contact lenses. Hold eyelids apart and flush eyes with water for at least 15 minutes. Get
immediate medical attention.
SKIN: Immediately wash skin with soap and plenty of water. Remove contaminated clothing. Get medical attention if irritation or rash
develops. Wash clothing before reuse.
INGESTION: Aspiration hazard. If swallowed, DO NOT induce vomiting. If vomiting occurs spontaneously, keep head below hips to prevent
aspiration of liquid into lungs. Never give anything by mouth to an unconscious person. Get medical attention immediately.
INHALATION: Remove to fresh air. If not breathing, give artificial respiration or give oxygen by trained personnel. Seek immediate medical
attention.
CHRONIC TOXICITY
CHRONIC EFFECTS: May cause damage to the liver and kidneys. Frequent or prolonged contact my defat and dry the skin, leading to
discomfort and dermatitis.
NOTES TO PHYSICIAN: Symptomatic and supportive therapy as needed. Following severe exposure medical follow-up should be
monitored for at least 48 hours.
5. FIRE FIGHTING MEASURES
GENERAL HAZARD: Flammable liquid and vapor.
EXTINGUISHING MEDIA: Water spray, carbon dioxide, dry chemical, or foam.
HAZARDOUS COMBUSTION PRODUCTS: Carbon monoxide and carbon dioxide.
EXPLOSION HAZARDS: Temperatures at or above the flash point could generate combustible mixtures. Avoid all ignition sources. “Empty”
containers retain product residue (liquid and/or vapor) and can be dangerous. DO NOT PRESSURIZE, CUT, WELD, BRAZE, SOLDER,
DRILL, GRIND, OR EXPOSE SUCH CONTAINERS TO HEAT, FL AME, SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES O F
IGNITION; THEY MAY EXPLODE AND CAUSE INJURY OR DEAT H. Empty drums should be completely drained, properly bunged and
promptly returned to a drum reconditioner, or properly disposed of.
FIRE FIGHTING PROCEDURES: Remove containers from the fire area if possible. Do not release runoff from fire control methods to
sewers or waterways.
FIRE FIGHTING EQUIPMENT: Firefighters should wear positive pressure self-contained breathing apparatus (SCBA) and consider use of
unmanned hose holders or monitor nozzles for fighting large fires.
SENSITIVE TO STATIC DISCHARGE: This material can accumulate static charges which can cause an incendiary electrical discharge.
6. ACCIDENTAL RELEASE MEASURES
SMALL SPILL: Eliminate sources of ignition. Evacuate the area. Clean-up should only be performed by trained personnel. People dealing
with a major spill should wear full protective clothing including appropriate respiratory protection. Prevent product spill from entering sewers
or waterways. Neutralize small spills with a decontaminant.
LARGE SPILL: Contain and absorb large spills onto an inert, non-flammable adsorbent carrier (earth or sand). Do not use combustible
Page 3 of 8
CHALLENGE 95

materials such as saw dust. Use only spark resistant and explosion proof recovery devices. Shovel into open-top drums or plastic bags for
further decontamination, if necessary. Wash the spill area clean with a liquid decontaminant. Remove and properly dispose of residues.
Notify applicable government authorities if release is reportable. (See CERCLA in Section 15).
ENVIRONMENTAL PRECAUTIONS
WATER SPILL: Do not discharge into drains or rivers.
GENERAL PROCEDURES: Refer to section 8 of SDS for personal protection details.
RELEASE NOTES: Composition and extent of any spill should be evaluated against local regulations and reported to the proper agencies, if
necessary.
7. HANDLING AND STORAGE
GENERAL PROCEDURES: Flammable liquid. Avoid contact with eyes, skin and clothing. Use only with adequate ventilation. Avoid
breathing vapor over open containers. Avoid open container exposure to damp air. Avoid breathing aerosols, mists, and vapors.
HANDLING: Use in a well ventilated area. Avoid heat, sparks, and open flames. Avoid breathing vapor and contact with eyes, skin, and
clothing. Use appropriate personal protective equipment as specified in Section 8. Handle and use in a manner consistent with good
industrial/manufacturing techniques and practices.
STORAGE: Store in a cool, well-ventilated, dry place, away from excessive heat in the original or similar container. Avoid sources of ignition
and incompatible materials. Keep containers tightly sealed. Avoid unnecessary contact.
SHELF LIFE: 12 months from date of shipment under manufacturers recommended storage conditions.
ELECTROSTATIC ACCUMULATION HAZARD: This material can accumulate static charges which can cause an incendiary electrical
discharge. Use proper bonding and/or grounding procedure.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
EXPOSURE GUIDELINES
OSHA HAZARDOUS COMPONENTS (29 CFR1910.1200)
EXPOSURE LIMITS
OSHA PEL ACGIH TLV SupplierOEL
Chemical Name ppm mg/m
3
ppm mg/m
3
ppm mg/m
3
Toluene
TWA 200 NE 50 188 100
[1]
375
[1]
STEL 300 NE NE NE 150
[1]
560
[1]
2-propanol
TWA 400 980 200 490 NE NE
STEL NE NE 400 960 NE NE
1,2,4-trimethylbenzene
TWA NE NE 25 123 25
[1]
125
[1]
STEL NE NE NE NE NE NE
Stoddard solvent
TWA 500 2900 100 572 350
[1]
NE
[1]
STEL NE NE NE NE NE NE
OSHA TABLE COMMENTS:
1. NIOSH REL
ENGINEERING CONTROLS: Use process enclosures, local exhaust ventilation, or other engineering controls to control airborne levels
below recommended exposure limits.
PERSONAL PROTECTIVE EQUIPMENT
EYES AND FACE: Safety goggles or glasses are recommended. Plastic face shields should be used for complete face protection to protect
against possible splashing or spraying of material. ANSI Z87.1 or approved equivalent.
SKIN: Chemical-resistant gloves and chemical goggles, face-shield, and synthetic apron or coveralls should be used to prevent contact with
eyes, skin, or clothing. Wear nitrile or neoprene gloves. Chemical resistant gloves lined with polyethylene offer maximum protection.
RESPIRATORY: Exhaust ventilation recommended. An organic vapor cartridge or fresh air supplied respirator (NIOSH approved) may be
Page 4 of 8
CHALLENGE 95

necessary for certain applications. Consider the type of application, environmental concentrations, and other materials being used
concurrently when determining respirator use and selection. Observe OSHA regulations for respirator use (29 CFR 1910.134).
PROTECTIVE CLOTHING: Protective clothing should be selected and used in accordance with ‘Guidelines for the Selection of Chemical
Protective Clothing’ published by ACGIH.
WORK HYGIENIC PRACTICES: Contaminated clothing should be changed and washed before reuse. Eating, drinking and smoking in
immediate work area should be prohibited. Wash hands before eating.
OTHER USE PRECAUTIONS: Facilities storing or utilizing this material should be equipped with an eyewash facility and a safety shower.
Training is important. Follow all label precautions.
9. PHYSICAL AND CHEMICAL PROPERTIES
PHYSICAL STATE: Liquid
ODOR: Solvent
COLOR: Yellow
pH: Not Applicable
FLASHPOINT AND METHOD: 4 C (39.2 F) Closed Cup (Toluene)
VAPOR PRESSURE: Not Established
VAPOR DENSITY: Not Established
BOILING POINT: Not Established
SOLUBILITY IN WATER: Negligible
SPECIFIC GRAVITY: Not Established
VISCOSITY: Not Established
10. STABILITY AND REACTIVITY
STABILITY: This product is stable under the recommended storage conditions.
POLYMERIZATION: Will not occur.
CONDITIONS TO AVOID: Avoid heat, sparks, open flames and other ignition sources.
POSSIBILITY OF HAZARDOUS REACTIONS: Hazardous reactions will not occur under normal transport or storage conditions.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon monoxide and carbon dioxide.
INCOMPATIBLE MATERIALS: Strong acids, strong bases, and strong oxidizing agents.
11. TOXICOLOGICAL INFORMATION
TOXICITY TO ANIMALS
Chemical Name
ORAL LD50
(rat)
DERMAL LD50
(rabbit)
INHALATION
LC
50 (rat)
Toluene 636 mg/kg 2 to 14 g/kg 26700 ppm (1h)
2-propanol 5800 mg/kg 16.4 ml/kg 12000 ppm (8 h)
1,2,4-trimethylbenzene 12.7 g/kg Not Established 18 g/m3
Stoddard solvent > 6000 mg/kg > 3000 ml/kg 5500 mg/m3 (4 h)
CHRONIC EFFECTS: Prolonged inhalation may be harmful. Prolonged or repeated exposure may cause lung injury. Prolonged or repeated
exposure may cause liver, kidney and central nervous system damage.
CARCINOGENICITY
Page 5 of 8
CHALLENGE 95

Chemical Name
IARC
Status
Toluene 3
2-propanol 3
IARC: This product contains substances that are not classifiable as carcinogens to humans.
IRRITATION: Causes eye, skin, and respiratory irritation.
SENSITIZATION: Risk of sensitization or allergic reactions among sensitive individuals.
NEUROTOXICITY: Central and/or peripheral nervous system damage. May cause drowsiness or dizziness.
REPRODUCTIVE EFFECTS: Suspected of damaging fertility. Suspected of damaging the unborn child.
TARGET ORGANS: Contains material which may cause damage to the following organs: respiratory tract, kidneys, liver, central nervous
system (CNS).
12. ECOLOGICAL INFORMATION
ENVIRONMENTAL DATA: This product may cause risk of hazardous effects to the environment.
ECOTOXICOLOGICAL INFORMATION: Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
Avoid release to the environment.
BIOACCUMULATION/ACCUMULATION: No data available
DISTRIBUTION: No data available
CHEMICAL FATE INFORMATION: No data available
13. DISPOSAL CONSIDERATIONS
DISPOSAL METHOD: The generation of waste should be avoided or minimized wherever possible. Empty containers or liners may retain
some product residues. This material and its container must be disposed of in a safe way. Dispose of surplus and non-recyclable products via
a licensed waste disposal contractor. Disposal of this product, solutions and any by-products should at all times comply with the requirements
of environmental protections and waste disposal legislation and any regional local authority requirements. Avoid dispersal of spilled material
and runoff and contact with soil, waterways, drains and sewers.
EMPTY CONTAINER: Empty containers may contain residue and can be dangerous. Do not attempt to refill or clean containers without
proper instructions. Empty drums should be completely drained and safely stored until appropriately reconditioned or disposed. Empty
containers should be taken for recycling, recovery, or disposal through suitably qualified or licensed contractor and in accordance with
governmental regulations. DO NOT PRESSURIZE, CUT, WELD, BRAZE, SOLDER, DRILL, GRIND, OR EXPOSE SUCH CO NTAINERS
TO HEAT, FLAME, SPARKS, STATIC ELECTRICITY, OR OTHE R SOURCES OF IGNITION. THEY MAY EXPLODE AND CAUSE
INJURY OR DEATH.
14. TRANSPORT INFORMATION
DOT (DEPARTMENT OF TRANSPORTATION) LAND
PROPER SHIPPING NAME: Flammable liquids, n.o.s.
TECHNICAL NAME: (toluene, mineral spirits)
PRIMARY HAZARD CLASS/DIVISION: 3
UN/NA NUMBER: UN1993
PACKING GROUP: II
ERG CODE: 128
LABEL: Flammable liquid
AIR (ICAO/IATA)
SHIPPING NAME: Flammable liquid, n.o.s.
TECHNICAL NAME: (toluene, mineral spirits)
UN/NA NUMBER: UN1993
PRIMARY HAZARD CLASS/DIVISION: 3
Page 6 of 8
CHALLENGE 95

PACKING GROUP: II
ERG CODE: 3H
LABEL: Flammable liquid
VESSEL (IMO/IMDG)
SHIPPING NAME: Flammable liquid, n.o.s.
TECHNICAL NAME: (toluene, mineral spirits)
UN/NA NUMBER: UN1993
PRIMARY HAZARD CLASS/DIVISION: 3
PACKING GROUP: II
LABEL: Flammable liquid
SPECIAL PROVISIONS: EmS: F-E, S-E
15. REGULATORY INFORMATION
UNITED STATES
SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZ ATION ACT)
311/312 HAZARD CATEGORIES: Acute health hazard. Chronic health hazard. Fire hazard.
313 REPORTABLE INGREDIENTS: This product contains the following substances subject to the reporting requirements of Section
313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR Part 372:
EPCRA SECTION 313 SUPPLIER NOTIFICATION
Chemical Name Wt.% CAS
Toluene 40 – 80108-88-3
2-propanol 0 – 2067-63-0
1,2,4-trimethylbenzene 5 – 1095-63-6
CERCLA (COMPREHENSIVE RESPONSE, COMPENSATION, AND L IABILITY ACT)
CERCLA REGULATORY: For this/these chemicals, release of more than the Reportable Quantity to the environment in a 24-hour
period requires notification to the National Response Center (800-424-8802 or 202-426-2675):
Chemical Name Wt.%
CERCLA
RQ
Toluene 40 – 801,000 lbs.
TSCA (TOXIC SUBSTANCE CONTROL ACT)
TSCA REGULATORY: This product contains chemical(s) subject to TSCA Section 12(b) export notification:
None
TSCA STATUS: This product or its components are listed in or exempt from the TSCA inventory requirements.
OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION (OSHA )
29 CFR1910.119—PROCESS SAFETY MANAGEMENT OF HIGHL Y HAZARDOUS CHEMICALS: None of the chemicals in
this product are considered highly hazardous by OSHA.
CALIFORNIA PROPOSITION 65: This product contains chemical(s) which are known to the State of California to cause cancer, birth
defects or other reproductive harm, and may be subject to the requirements of California Proposition 65 (CA Health & Safety Code
Section 25249.5):
Chemical Name Wt.% Listed
Toluene 40 – 80
Cancer
Developmental Toxicity
OSHA HAZARD COMM. RULE: The contents of the MSDS comply with the OSHA Hazard Communication Standard 29 CFR
1910.1200.
Page 7 of 8
CHALLENGE 95

CANADA
WHMIS HAZARD SYMBOL AND CLASSIFICATION
Flammable
Liquid
Toxic
WHMIS CLASSIFICATION
Class B2: Flammable liquid
Class D-2A: Poisonous and infectious material (Very toxic).
Class D-2B: Poisonous and infectious material (Toxic).
WHMIS HEALTH EFFECTS CRITERIA
D2A – Teratogenicity and embryotoxicity
D2B – Skin irritation
D2B – Eye irritation
WHMIS (WORKPLACE HAZARDOUS MATERIALS INFORMATION SY STEM): This product has been classified according to the
hazard criteria of the CPR and the MSDS contains all the information required by the CPR.
DOMESTIC SUBSTANCE LIST (INVENTORY): All components in this product are listed in or exempted from the Domestic
Substances List (DSL) or the Non-Domestic Substances List (NDSL).
16. OTHER INFORMATION
REASON FOR ISSUE: New Issue
HMIS RATING
HEALTH * 2
FLAMMABILITY 3
PHYSICAL HAZARD 1
PERSONAL PROTECTION X
NFPA CODES

3
2 1

HMIS RATINGS NOTES: Personal Protection: See Section 8
MANUFACTURER DISCLAIMER: This information is furnished without warranty, expressed or implied, except that is accurate to the best
knowledge of BJB Enterprises, Inc. The data on this sheet relates only to the specific material designated herein. BJB Enterprises, Inc.
assumes no legal responsibility for use or reliance upon this data.
Page 8 of 8
CHALLENGE 95

17AMT660-D_SDS.pdf

by | Sep 27, 2025

Able Industrial Products Inc.
SAFETY DATA SHEET
GHS GT60P printed: 02/12/18 page 1 of 5
1.PRODUCT IDENTIFICATION
TRADE NAME: AMT 660P
OTHER MEANS OF
IDENTIFICATION:
RECOMMENDED USE OF
PRODUCT:
Mold-making Rubber
SUPPLIER S DETAILS: Able Industrial Products
2006 S Baker Ave
Ontario, Calif. 91761
909-930-1585
Fax 909-930-1587
EMERGENCY CONTACT: CHEMTREC (24 Hours):1-800-424-9300
2.HAZARDS IDENTIFICATION
GHS CLASSIFICATION
PHYSICAL HAZARDS Not Classified
HEALTH HAZARDS Not Classified
ENVIRONMENTAL HAZARDS Not Classified
GHS LABEL ELEMENTS
PICTOGRAMS None
SIGNAL WORDS None
HAZARD STATEMENTS None
PRECAUTIONARY STATEMENTS
[PREVENTION] None
[RESPONSE] None
[STORAGE] None
[DISPOSAL] None
3.COMPOSITION AND INFORMATION ON INGREDIENTS

Able Industrial Products
SAFETY DATA SHEET
GHS GT60P printed: 02/12/18 page 2 of 5
Substance or Mixture Mixture
Hazardous Ingredients CAS# Percentage (%)
Quartz 14808-60-7 30-40
*Quartz or crystalline silica is considered to be a nuisance dust. All hazards associated with the
substance are only applicable when the substance is in its respirable form. However, crystalline silica is
not expected to be hazardous when compounded into a liquid polymer like its current state in this
product because it is no longer respirable under normal conditions. Therefore, all hazards associated
with respirable quartz are not listed.
4.FIRST AID MEASURES
INGESTION: Seek medical attention; Do NOT induce vomiting.
SKIN CONTACT: Remove contaminated clothing immediately and dispose of safely.
When in contact with the skin, clean with soap and water.
INHALATION: No first aid should be needed. Remove to fresh air.
EYE CONTACT: Immediately flush with COOL water for 15 minutes; Call a
physician if irritation persists.
PROTECTION FOR FIRST-
AIDERS:
A rescuer should wear personal protective equipment, such as
rubber gloves and air-tight goggles

5.FIRE-FIGHTING MEASURES
SUITABLE EXTINGUISHING
MEDIA:
Foam, carbon dioxide, dry chemical
SPECIFIC FIRE HAZARDS: Fire will form hazardous combustion gases of carbon dioxide
(CO2), carbon monoxide (CO), SiO2, and oxides of nitrogen (NOx).
Product contains silicone, which is known to produce
formaldehyde when temperatures reach in excess of 150
o
C.
Formaldehyde is a known skin, eye, and throat irritant as well as a
potential cancer hazard
FIREFIGHTER EQUIPMENT: Wear respirator and all protective coverings.

6.ACCIDENTAL RELEASE MEASURES
PERSONAL PRECATIONS,
PROTECTIVE EQUIPMENT AND
EMERGENCY:
Safety glasses and gloves are suggested to prevent eye and skin
contact. Provide sufficient ventilation.
ENVIRONMENTAL
PRECAUTIONS:
Prevent product from entering drains.
CLEAN UP: Scrape up and disposed of in accordance with appropriate laws
and regulations.
7.HANDLING AND STORAGE

Able Industrial Products
SAFETY DATA SHEET
GHS GT60P printed: 02/12/18 page 3 of 5
HANDLING: Wear protective equipment; Avoid contact with skin and eyes.
STORAGE: Keep container tightly closed. Store in a cool, dry place. Keep
away from oxidizing material.
8.EXPOSURE CONTROLS AND PERSONAL PROTECTION
EXPOSURE LIMITS:
Hazardous Ingredient CAS# Limit/Set by
Quartz 14808-60-7 For Respirable Dust – TWA: 0.025mg/m3(ACGIH),
0.3mg/m3(OSHA)
ENGINEERING CONTROLS: None Available
PERSONAL PROTECTIVE
EQUIPMENT:
RESPIRATORY PROTECTION: Not required under normal use
HAND PROTECTION Protective gloves
EYE PROTECTION Wear safety glasses or goggles. Face shield if situation requires
SKIN AND BODY PROTECTION Protective clothing if situation requires

9.PHYSICAL AND CHEMICAL PROPERTIES
PHYSICAL STATE: Flowable Paste
ODOR: No Odor
ODOR THRESHOLD: Not Available
pH: Not Available
MELTING POINT: Not Available
BOILING POINT RANGE: Not Applicable, will decompose before it will boil
FLASH POINT: >205
o
F (Setaflash)
EVAPORATION RATE: Not Available
FLAMMABILITY(solid/gas): Not Available
EXPLOSION LIMITS:
UPPER Not Available
LOWER Not Available
VAPOR PRESSURE: <0.1mbar @ 68 o F VAPOR DENSITY: All vapors are denser than air RELATIVE DENSITY: 1.36 g/mL SOLUBILITY: Not soluble in water PARTITION COEFFICIENT: N- OCTANOL/WATER: Not Available AUTO-IGNITION TEMPERATURE: Not Available DECOMPOSITION TEMPERATURE: >150
o
C
VISCOSITY: 53,000 cP

10.STABILITY AND REACTIVITY

Able Industrial Products
SAFETY DATA SHEET
GHS GT60P printed: 02/12/18 page 4 of 5
REACTIVITY: Product is designed to react with a catalyst to initiate
vulcanization.
CHEMICAL STABILITY: Stable in the absence of contamination
HAZARDOUS REACTIONS: None
CONDITIONS TO AVOID: Avoid contact with strong acids, alkalis, and oxidizing agents.
HAZARDOUS DECOMPOSITION
PRODUCTS:
Hazardous combustion gases of carbon dioxide(CO2), carbon
monoxide(CO), SiO2, and oxides of nitrogen (NOx).
Product contains silicone, which is known to produce
formaldehyde when temperatures reach in excess of 150
o
C.
Formaldehyde is a known skin, eye, and throat irritant as well as a
potential cancer hazard
INCOMPATIBILITY: Acids, Alkalis, Oxidizing Agents

11.TOXICOLOGICAL INFORMATION
ACUTE TOXICITY: Oral LD50(Rat): 8186 mg/kg (calculated from known toxicities)
SKIN CORROSION/IRRITATION: Not Available
EYE DAMAGE/IRRITATION: Not Available
RESPIRATORY OR SKIN
SENSITATION:
Not Available
GERM CELL MUTAGENICITY: Not Available
CARCINOGENICITY: Quartz (CAS 14808-60-7) is listed by the IARC and the NTP to
cause cancer in humans.
REPRODUCTIVE TOXICITY: Not Available
STOST- SINGLE EXPOSURE: Not Available
STOST- REPEATED EXPOSURE: Not Available
ASPIRATION HAZARD: Not Available

12.ECOLOGICAL INFORMATION
ECOTOXICITY: Do not allow to enter soil, waterways or waste water canal. It is
not allowed to be released into biological sewage treatment
plants. Ecological data is not available.
PERSISTENCE/DEGRADABILITY: Not Available
BIOACCUMULATIVE POTENTIAL: Not Available
MOBILITY IN SOIL: Not Available

13.DISPOSAL CONSIDERATIONS
Recycle to process, if possible. Consult your local regional authorities. You may be able to burn in a
chemical incinerator equipped with an afterburner and scrubber system. Observe all federal, state and local
regulations when disposing of the substance.
14.TRANSPORT INFORMATION
UN/NA Number: Not Regulated
DOT SHIPPING NAME: Not Regulated
DOT HAZARD CLASS: Not Regulated
IMDG P.S.N.: Not Regulated

Able Industrial Products
SAFETY DATA SHEET
GHS GT60P printed: 02/12/18 page 5 of 5
IMDG CLASS: Not Regulated
IMDG PACKING GROUP: Not Regulated
IMDG Marine Pollutant: Not Regulated
IATA – P.S.N.: Not Regulated
IATA – CLASS: Not Regulated
IATA PACKING GROUP: Not Regulated
This product and its ingredients are NOT considered dangerous goods according to the UN Model
Regulations, ADR, RID, and the ADN.

15.REGULATORY INFORMATION
US REGULATIONS
US SARA REPORTING REQUIREMENTS: The components of this product are subject to the reporting
requirements of Section 302, 304, and 313 of Title III of the Superfund Amendments and Reauthorization
Act, and are listed as follows:
Hazardous Ingredient SARA 302
(40 CFR 355,
Appendix A)
SARA 304
(40 CFR Table
302.4)
SARA 313
(40 CFR 372.65)
Quartz, Amorphous Silica No No No
U.S. SARA THRESHOLD PLANNING QUANTITY: There are no specific Threshold Planning Quantities for
the components of this product. The default Federal MSDS submission and inventory requirement filing
threshold of 10,000 lbs(4,540 kg) therefore applies, per 40 CFR 370.20
U.S. CERCLA REPORTABLE QUANTITY (RQ): None
SARA 311/312(40 CFR 370) HAZARDS: Acute: No, Chronic: No, Fire: No, Pressure: No
CALIFORNIA, (PROPOSITION 65): Quartz, Crystalline silica
TSCA INVENTORY STATUS: These materials or all of their contents are listed on the Toxic Substances
Control Act (TSCA).

16. OTHER INFORMATION
HMIS Rating: Health-1, Fire-0, Reactive-0
This product contains crystalline silica which is hazardous if it is inhaled. However, in this product, the silica is
wetted out with various polyorganosiloxanes to where it is no longer in powder form, meaning it is incapable of
becoming airborne under normal use conditions. Because the product is a mixture, the majority of the data
used was transferred from the safety data sheets of the product s hazardous ingredients, whose manufacturer
identity we wish to remain anonymous for competitive reasons.
We believe the above information is correct as of the date of this MSDS. However, as this information and the
conditions under which the product are used are beyond the control of GT PRODUCTS, INC., it is the user’s
obligation to determine the conditions for the safe use of the product. No warranty, expressed or implied, is
hereby made.
Date Created/Revised: 2/17/2020 Name Change Made By: Rick Viramontes

17AMT440PAD_SDS.pdf

by | Sep 27, 2025

Able Industrial Products , Inc.
SAFETY DATA SHEET
GHS GT40P printed: 02/12/18 page 1 of 5
1.PRODUCT IDENTIFICATION
TRADE NAME: AMT 440P
OTHER MEANS OF
IDENTIFICATION:
RECOMMENDED USE OF
PRODUCT:
Mold-making Rubber
SUPPLIER S DETAILS: Able Industrial Products
2006 S BAker Ave
Onatrio, Calif. 91761
909-930-1585
Fax 909-930-1587
EMERGENCY CONTACT: CHEMTREC (24 Hours):1-800-424-9300
2.HAZARDS IDENTIFICATION
GHS CLASSIFICATION
PHYSICAL HAZARDS Not Classified
HEALTH HAZARDS Not Classified
ENVIRONMENTAL HAZARDS Not Classified
GHS LABEL ELEMENTS
PICTOGRAMS None
SIGNAL WORDS None
HAZARD STATEMENTS None
PRECAUTIONARY STATEMENTS
[PREVENTION] None
[RESPONSE] None
[STORAGE] None
[DISPOSAL] None
3.COMPOSITION AND INFORMATION ON INGREDIENTS

Able Industrial Products , Inc.
SAFETY DATA SHEET
GHS GT40P printed: 02/12/18 page 2 of 5
Substance or Mixture Mixture
Hazardous Ingredients CAS# Percentage (%)
Quartz 14808-60-7 25-35
*Quartz or crystalline silica is considered to be a nuisance dust. All hazards associated with the
substance are only applicable when the substance is in its respirable form. However, crystalline silica is
not expected to be hazardous when compounded into a liquid polymer like its current state in this
product because it is no longer respirable under normal conditions. Therefore, all hazards associated
with respirable quartz are not listed.
4.FIRST AID MEASURES
INGESTION: Seek medical attention; Do NOT induce vomiting.
SKIN CONTACT: Remove contaminated clothing immediately and dispose of safely.
When in contact with the skin, clean with soap and water.
INHALATION: No first aid should be needed. Remove to fresh air.
EYE CONTACT: Immediately flush with COOL water for 15 minutes; Call a
physician if irritation persists.
PROTECTION FOR FIRST-
AIDERS:
A rescuer should wear personal protective equipment, such as
rubber gloves and air-tight goggles

5.FIRE-FIGHTING MEASURES
SUITABLE EXTINGUISHING
MEDIA:
Foam, carbon dioxide, dry chemical
SPECIFIC FIRE HAZARDS: Fire will form hazardous combustion gases of carbon dioxide
(CO2), carbon monoxide (CO), SiO2, and oxides of nitrogen (NOx).
Product contains silicone, which is known to produce
formaldehyde when temperatures reach in excess of 150
o
C.
Formaldehyde is a known skin, eye, and throat irritant as well as a
potential cancer hazard
FIREFIGHTER EQUIPMENT: Wear respirator and all protective coverings.

6.ACCIDENTAL RELEASE MEASURES
PERSONAL PRECATIONS,
PROTECTIVE EQUIPMENT AND
EMERGENCY:
Safety glasses and gloves are suggested to prevent eye and skin
contact. Provide sufficient ventilation.
ENVIRONMENTAL
PRECAUTIONS:
Prevent product from entering drains.
CLEAN UP: Scrape up and disposed of in accordance with appropriate laws
and regulations.
7.HANDLING AND STORAGE

Able Industrial Products , Inc.
SAFETY DATA SHEET
GHS GT40P printed: 02/12/18 page 3 of 5
HANDLING: Wear protective equipment; Avoid contact with skin and eyes.
STORAGE: Keep container tightly closed. Store in a cool, dry place. Keep
away from oxidizing material.
8.EXPOSURE CONTROLS AND PERSONAL PROTECTION
EXPOSURE LIMITS:
Hazardous Ingredient CAS# Limit/Set by
Quartz 14808-60-7 For Respirable Dust – TWA: 0.025mg/m3(ACGIH),
0.3mg/m3(OSHA)
ENGINEERING CONTROLS: None Available
PERSONAL PROTECTIVE
EQUIPMENT:
RESPIRATORY PROTECTION: Not required under normal use
HAND PROTECTION Protective gloves
EYE PROTECTION Wear safety glasses or goggles. Face shield if situation requires
SKIN AND BODY PROTECTION Protective clothing if situation requires

9.PHYSICAL AND CHEMICAL PROPERTIES
PHYSICAL STATE: Flowable Paste
ODOR: No Odor
ODOR THRESHOLD: Not Available
pH: Not Available
MELTING POINT: Not Available
BOILING POINT RANGE: Not Applicable, will decompose before it will boil
FLASH POINT: >205
o
F (Setaflash)
EVAPORATION RATE: Not Available
FLAMMABILITY(solid/gas): Not Available
EXPLOSION LIMITS:
UPPER Not Available
LOWER Not Available
VAPOR PRESSURE: <0.1mbar @ 68 o F VAPOR DENSITY: All vapors are denser than air RELATIVE DENSITY: 1.35 g/mL SOLUBILITY: Not soluble in water PARTITION COEFFICIENT: N- OCTANOL/WATER: Not Available AUTO-IGNITION TEMPERATURE: Not Available DECOMPOSITION TEMPERATURE: >150
o
C
VISCOSITY: 44,200 cP

10.STABILITY AND REACTIVITY

Able Industrial Products , Inc.
SAFETY DATA SHEET
GHS GT40P printed: 02/12/18 page 4 of 5
REACTIVITY: Product is designed to react with a catalyst to initiate
vulcanization.
CHEMICAL STABILITY: Stable in the absence of contamination
HAZARDOUS REACTIONS: None
CONDITIONS TO AVOID: Avoid contact with strong acids, alkalis, and oxidizing agents.
HAZARDOUS DECOMPOSITION
PRODUCTS:
Hazardous combustion gases of carbon dioxide(CO2), carbon
monoxide(CO), SiO2, and oxides of nitrogen (NOx).
Product contains silicone, which is known to produce
formaldehyde when temperatures reach in excess of 150
o
C.
Formaldehyde is a known skin, eye, and throat irritant as well as a
potential cancer hazard
INCOMPATIBILITY: Acids, Alkalis, Oxidizing Agents

11.TOXICOLOGICAL INFORMATION
ACUTE TOXICITY: Oral LD50(Rat): 13,537 mg/kg (calculated from known toxicities)
SKIN CORROSION/IRRITATION: Not Available
EYE DAMAGE/IRRITATION: Not Available
RESPIRATORY OR SKIN
SENSITATION:
Not Available
GERM CELL MUTAGENICITY: Not Available
CARCINOGENICITY: Quartz (CAS 14808-60-7) is listed by the IARC and the NTP to
cause cancer in humans.
REPRODUCTIVE TOXICITY: Not Available
STOST- SINGLE EXPOSURE: Not Available
STOST- REPEATED EXPOSURE: Not Available
ASPIRATION HAZARD: Not Available

12.ECOLOGICAL INFORMATION
ECOTOXICITY: Do not allow to enter soil, waterways or waste water canal. It is
not allowed to be released into biological sewage treatment
plants. Ecological data is not available.
PERSISTENCE/DEGRADABILITY: Not Available
BIOACCUMULATIVE POTENTIAL: Not Available
MOBILITY IN SOIL: Not Available

13.DISPOSAL CONSIDERATIONS
Recycle to process, if possible. Consult your local regional authorities. You may be able to burn in a
chemical incinerator equipped with an afterburner and scrubber system. Observe all federal, state and local
regulations when disposing of the substance.
14.TRANSPORT INFORMATION
UN/NA Number: Not Regulated
DOT SHIPPING NAME: Not Regulated
DOT HAZARD CLASS: Not Regulated
IMDG P.S.N.: Not Regulated

Able Industrial Products , Inc.
SAFETY DATA SHEET
GHS GT40P printed: 02/12/18 page 5 of 5
IMDG CLASS: Not Regulated
IMDG PACKING GROUP: Not Regulated
IMDG Marine Pollutant: Not Regulated
IATA – P.S.N.: Not Regulated
IATA – CLASS: Not Regulated
IATA PACKING GROUP: Not Regulated
This product and its ingredients are NOT considered dangerous goods according to the UN Model
Regulations, ADR, RID, and the ADN.

15.REGULATORY INFORMATION
US REGULATIONS
US SARA REPORTING REQUIREMENTS: The components of this product are subject to the reporting
requirements of Section 302, 304, and 313 of Title III of the Superfund Amendments and Reauthorization
Act, and are listed as follows:
Hazardous Ingredient SARA 302
(40 CFR 355,
Appendix A)
SARA 304
(40 CFR Table
302.4)
SARA 313
(40 CFR 372.65)
Quartz, Amorphous Silica No No No
U.S. SARA THRESHOLD PLANNING QUANTITY: There are no specific Threshold Planning Quantities for
the components of this product. The default Federal MSDS submission and inventory requirement filing
threshold of 10,000 lbs(4,540 kg) therefore applies, per 40 CFR 370.20
U.S. CERCLA REPORTABLE QUANTITY (RQ): None
SARA 311/312(40 CFR 370) HAZARDS: Acute: No, Chronic: No, Fire: No, Pressure: No
CALIFORNIA, (PROPOSITION 65): Quartz, Crystalline silica
TSCA INVENTORY STATUS: These materials or all of their contents are listed on the Toxic Substances
Control Act (TSCA).

16. OTHER INFORMATION
HMIS Rating: Health-1, Fire-0, Reactive-0
This product contains crystalline silica which is hazardous if it is inhaled. However, in this product, the silica is
wetted out with various polyorganosiloxanes to where it is no longer in powder form, meaning it is incapable of
becoming airborne under normal use conditions. Because the product is a mixture, the majority of the data
used was transferred from the safety data sheets of the product s hazardous ingredients, whose manufacturer
identity we wish to remain anonymous for competitive reasons.
We believe the above information is correct as of the date of this MSDS. However, as this information and the
conditions under which the product are used are beyond the control of GT PRODUCTS, INC., it is the user’s
obligation to determine the conditions for the safe use of the product. No warranty, expressed or implied, is
hereby made.
Date Created/Revised: 2/12/18 Made By: Daniel Shaw