by | Sep 27, 2025
Safety Data Sheet
Revision: 01/01/2021
High Temperature Fiberglass Flatstock
Product name: High Temperature Fiberglass Flatstock
Product code: Cured Epoxy Fiberglass Laminate
Details of the supplier of the safety data sheet
Manufacturer:
Reklein Plastics Inc.
42130 Mound
Rd.
Sterling Heights
MI 48314
USA
586 739-8850
S~c1:i’on i: Hazartlldentificatio
Classification
of the substance or mixture:
Label elements
Signal Word:
None
Hazard Phrases: No phrases apply
Precaution Phrases: No phrases apply
Response Phrases: No phrases apply
Storage & Disposal Phrases: No phrases apply
Other hazards: Avoid inhalation of dust when cutting
S ectien 3 -Com
Mixtures: Chemical Name CAS No. Concentration
Glass Oxide 65997 -17 -300000
Fiberglass Fabric cured with epoxy resin 100%
Section 4 -Firs.1-Aid Measures
Description
of first-aid measure
Inhalaton:
Move victim to fresh air.
Skin: Wash with plenty of soap and water
Eye: Flush eyes with plenty of water. Remove any contact lenses and continue
flushing for at least
15 minutes.
Ingestion: Not likely due to form.
Most important symptoms and effects, both acute and delayed:
Irritated eyes, coughing, irritated throat.
Section 5 -Fire-Fighting Measures
Suitable extinguishing media:
C02, Foam, Dry Chemical, Sand
Advice to firefighters: Use NIOSH/MSHA approved positive pressure self-contained breathing apparatus when
any material
in involved in a fire. Evacuate area and fight fire from a safe distance.
Section 6 -Accidental Release Measures
Personal precautions, protective equipment and emergency procedures:
N/A
Methods and material for containment and clean up: N/A
Section 7 -Handling and Storage
Precautions for safe handling:
N/A
Conditions for safe storage, including any incompatibilities: N/A
Section 8 -Exposure Controls/Personal Protection
Respiratory Equipment:
An approved dust mask may be worn if needed.
Eye Protection: Eye protection is recommended .
Other Protective Clothing: No data available.
Engineering Controls: Provide general local exhaust to minimize dust.
Sections 9 -Physical and Chemical Properties
Appearance: Solid sheet
Color: Black
Odor: No noticeable odor
Density: N/A
pH: N/A
Melting point/Freezing point: N/A
Boiling point: N/A
Flash point: No data
Evaporation rate: N/A
Flammability: N/A
Upper/lower flammability or explosive limits: N/A
Vapor pressure: N/A
Vapor density: N/A
Solubility: N/A
Partition coefficient: NIA
Auto-ignition temp: N/A
Decomposition temp: N/A
Viscosity: N/A
Section 10 -Stability and Reactivity
Reactivity:
N/A
Chemical stability: Product is stable at room temperature under normal storage and handling conditions.
Conditions to avoid: No data
Hazardous decomposition products: Thermal oxidative decomposition of product can produce C02, CO,
Aldehydes
Section 11 -Toxicological Information
Toxicological Information-
Dust may cause eye irritation.
Section 12 -Ecological Information
General Ecological Information-
Persistence and Degradability-
Not biodegradable.
Section 13 -Disposal Considerations
Waste Disposal Method-
Dispose of in accordance with local, state and federal regulations.
Section 14 -Transport Information
Land Transport (US DOT)
DOT Proper Shippping Name-
Fiberglass Flatstock
Section 15 -Regulatory Information
EPA Regulations
N/A
Regulatory Information- Not a “Hazardous Chemical” as defined by the OSHA Hazard
Communication Standard.
Section 16 -Other information
Company policy or disclaimer-
This information is furnished without warranty, representation, inducement or
license of any kind except that it is accurate to the best of Reklein Plastics knowledge or obtained from sources believed
to be accurate. Reklein Plastics does not assume any legal responsibility for use or reliance upon same. Customers are
encouraged
to conduct their own tests before using any product.
by | Sep 27, 2025
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 1 / 9
SECTION 1: Identification of the substance/mixture and of the company/undertaking
1.1 Product identifier
Trade name : SikaBlock M600
1.2 Relevant identified uses of the substance or mixture and uses advised against
At present there is no complete information available on identified uses. When the data becomes
available, it will be integrated into the safety data sheet.
1.3 Details of the supplier of the safety data sheet
Company : Sika Deutschland GmbH
Kornwestheimer Str. 103-107
70439 Stuttgart
Telephone : +4971180090
1.4 Emergency telephone number
Emergency telephone num-
ber
:
0173-6774799 Out of office hours only
EHS@de.sika.com
SECTION 2: Hazards identification
2.1 Classification of the substance or mixture
Type of product : Mixture
Classification (67/548/EEC, 1999/45/EC)
Not a hazardous substance or mixture.
2.2 Label elements
Labelling according to EC Directives: 1999/45/EC
The product does not need to be labelled in accordance with EC directives or respective national
laws.
2.3 Other hazards
This mixture contains no substance considered to be persistent, bioaccumulating nor toxic (PBT).
This mixture contains no substance considered to be very persistent nor very bioaccumulating
(vPvB).
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 2 / 9
SECTION 3: Composition/information on ingredients
3.2 Mixtures
Remarks : No hazardous ingredients
SECTION 4: First aid measures
4.1 Description of first aid measures
General advice : No hazards which require special first aid measures.
If inhaled : If symptoms persist, call a physician.
In case of skin contact : Take off contaminated clothing and shoes immediately.
Wash off with soap and plenty of water.
In case of eye contact : Flush eyes with water as a precaution.
Remove contact lenses.
Keep eye wide open while rinsing.
If swallowed : Clean mouth with water and drink afterwards plenty of water.
Do not give milk or alcoholic beverages.
Never give anything by mouth to an unconscious person.
4.2 Most important symptoms and effects, both acute and delayed
Symptoms : See Section 11 for more detailed information on health effects
and symptoms.
Risks : No known significant effects or hazards.
4.3 Indication of any immediate medical attention and special treatment needed
Treatment : Treat symptomatically.
SECTION 5: Firefighting measures
5.1 Extinguishing media
Suitable extinguishing media : Use extinguishing measures that are appropriate to local cir-
cumstances and the surrounding environment.
5.2 Special hazards arising from the substance or mixture
5.3 Advice for firefighters
Special protective equipment
for firefighters
: In the event of fire, wear self-contained breathing apparatus.
Further information : Standard procedure for chemical fires.
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 3 / 9
SECTION 6: Accidental release measures
6.1 Personal precautions, protective equipment and emergency procedures
Personal precautions : Avoid dust formation.
6.2 Environmental precautions
Environmental precautions : No special environmental precautions required.
6.3 Methods and materials for containment and cleaning up
Methods for cleaning up : Keep in suitable, closed containers for disposal.
Sweep up or vacuum up spillage and collect in suitable con-
tainer for disposal.
6.4 Reference to other sections
For personal protection see section 8.
SECTION 7: Handling and storage
7.1 Precautions for safe handling
Advice on safe handling : For personal protection see section 8. No special handling
advice required. Follow standard hygiene measures when
handling chemical products
Advice on protection against
fire and explosion
: Avoid dust formation. Provide appropriate exhaust ventilation
at places where dust is formed.
Hygiene measures : General industrial hygiene practice.
7.2 Conditions for safe storage, including any incompatibilities
Requirements for storage
areas and containers
: Keep container tightly closed in a dry and well-ventilated
place. Store in accordance with local regulations.
Advice on common storage : No special restrictions on storage with other products.
Other data : No decomposition if stored and applied as directed.
7.3 Specific end use(s)
Specific use(s) : no data available
SECTION 8: Exposure controls/personal protection
8.1 Control parameters
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 4 / 9
Components with workplace control parameters
Contains no substances with occupational exposure limit values.
8.2 Exposure controls
Personal protective equipment
Eye protection : Safety glasses
Hand protection : Chemical-resistant, impervious gloves complying with an ap-
proved standard must be worn at all times when handling
chemical products. Reference number EN 374. Follow manu-
facturer specifications.
Skin and body protection : Protective clothing (e.g. Safety shoes acc. to EN ISO 20345,
long-sleeved working clothing, long trousers). Rubber aprons
and protective boots are additionaly recommended for mixing
and stirring work.
Respiratory protection : No special measures required.
Environmental exposure controls
General advice : No special environmental precautions required.
SECTION 9: Physical and chemical properties
9.1 Information on basic physical and chemical properties
Appearance : solid
Colour : brown
Odour : characteristic
Odour Threshold : no data available
Flash point : Note: not applicable
Ignition temperature : no data available
Lower explosion limit (Vol%) : no data available
Upper explosion limit (Vol%) : no data available
Flammability (solid, gas) : no data available
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 5 / 9
Oxidizing properties : no data available
Auto-ignition temperature : no data available
pH : Note: not applicable
Melting point/range / Freez-
ing point
: no data available
Boiling point/boiling range : no data available
Vapour pressure : no data available
Density : ca.0,64 g/cm3
at 20 C
Water solubility : Note: insoluble
Partition coefficient: n-
octanol/water
: no data available
Viscosity, dynamic : Note: not applicable
Viscosity, kinematic : Note: not applicable
Relative vapour density : no data available
Evaporation rate : no data available
9.2 Other information
no data available
SECTION 10: Stability and reactivity
10.1 Reactivity
No dangerous reaction known under conditions of normal use.
10.2 Chemical stability
The product is chemically stable.
10.3 Possibility of hazardous reactions
Hazardous reactions : No hazards to be specially mentioned.
Dust may form explosive mixture in air.
10.4 Conditions to avoid
Conditions to avoid : no data available
10.5 Incompatible materials
Materials to avoid : no data available
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 6 / 9
10.6 Hazardous decomposition products
SECTION 11: Toxicological information
11.1 Information on toxicological effects
Acute toxicity
no data available
Skin corrosion/irritation
Product
no data available
Serious eye damage/eye irritation
Product
no data available
Respiratory or skin sensitisation
Product
no data available
Germ cell mutagenicity
Product
Mutagenicity : no data available
Carcinogenicity
Product
Carcinogenicity : no data available
Reproductive Toxicity/Fertility
Reproductive toxicity : no data available
no data available
Reproductive Toxicity/Development/Teratogenicity
Teratogenicity : no data available
no data available
STOT – single exposure
no data available
STOT – repeated exposure
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 7 / 9
no data available
Aspiration toxicity
no data available
SECTION 12: Ecological information
12.1 Toxicity
no data available
12.2 Persistence and degradability
no data available
12.3 Bioaccumulative potential
no data available
12.4 Mobility in soil
no data available
12.5 Results of PBT and vPvB assessment
Product:
Assessment : This substance/mixture contains no components considered
to be either persistent, bioaccumulative and toxic (PBT), or
very persistent and very bioaccumulative (vPvB) at levels of
0.1% or higher.
12.6 Other adverse effects
no data available
SECTION 13: Disposal considerations
13.1 Waste treatment methods
Product : In accordance with the EWC Waste Regulation the classifica-
tion of waste is to be assigned to the jurisdiction of the origin
of waste. Therefore, it is not possible to assign a particular
waste identification number.
Completely emptied packagings may be given for recycling.
Empty packaging may still contain hazardous residues. Empty
packaging should be removed by a licensed waste contractor.
Sika has agreed disposal contracts for all packaging which is
brought into circulation in Germany.
For further details see www.sika.de
SECTION 14: Transport information
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 8 / 9
ADR
Not dangerous goods
IATA
Not dangerous goods
IMDG
Not dangerous goods
14.6 Special precautions for user
no data available
14.7 Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
not applicable
SECTION 15: Regulatory information
15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture
Prohibition/Restriction
REACH – Restrictions on the manufacture, placing on
the market and use of certain dangerous substances,
preparations and articles (Annex XVII)
: not applicable
REACH – Candidate List of Substances of Very High
Concern for Authorisation (Article 59).
: None of the components are listed
(=> 0.1 %).
REACH – List of substances subject to authorisation
(Annex XIV)
: not applicable
REACH Information: All substances contained in our Products are
– preregistered or registered by our upstream suppliers, and/or
– preregistered or registered by us, and/or
– excluded from the regulation, and/or
– exempted from the registration.
Water contaminating class
(Germany)
: nwg not water endangering
Gem VwVws vom 30.Juli 2005
VOC-CH (VOCV) : no VOC duties
VOC-EU (solvent) : not applicable
15.2 Chemical Safety Assessment
This product contains substances for which Chemical Safety Assessments are still required.
SECTION 16: Other information
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 9 / 9
The information contained in this Safety Data Sheet corresponds to our level of knowledge at the
time of publication. All warranties are excluded. Our most current General Sales Conditions shall
apply. Please consult the product data sheet prior to any any use and processing.
Changes as compared to previous version !
by | Sep 27, 2025
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 1 / 9
SECTION 1: Identification of the substance/mixture and of the company/undertaking
1.1 Product identifier
Trade name : SikaBlock M600
1.2 Relevant identified uses of the substance or mixture and uses advised against
At present there is no complete information available on identified uses. When the data becomes
available, it will be integrated into the safety data sheet.
1.3 Details of the supplier of the safety data sheet
Company : Sika Deutschland GmbH
Kornwestheimer Str. 103-107
70439 Stuttgart
Telephone : +4971180090
1.4 Emergency telephone number
Emergency telephone num-
ber
:
0173-6774799 Out of office hours only
EHS@de.sika.com
SECTION 2: Hazards identification
2.1 Classification of the substance or mixture
Type of product : Mixture
Classification (67/548/EEC, 1999/45/EC)
Not a hazardous substance or mixture.
2.2 Label elements
Labelling according to EC Directives: 1999/45/EC
The product does not need to be labelled in accordance with EC directives or respective national
laws.
2.3 Other hazards
This mixture contains no substance considered to be persistent, bioaccumulating nor toxic (PBT).
This mixture contains no substance considered to be very persistent nor very bioaccumulating
(vPvB).
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 2 / 9
SECTION 3: Composition/information on ingredients
3.2 Mixtures
Remarks : No hazardous ingredients
SECTION 4: First aid measures
4.1 Description of first aid measures
General advice : No hazards which require special first aid measures.
If inhaled : If symptoms persist, call a physician.
In case of skin contact : Take off contaminated clothing and shoes immediately.
Wash off with soap and plenty of water.
In case of eye contact : Flush eyes with water as a precaution.
Remove contact lenses.
Keep eye wide open while rinsing.
If swallowed : Clean mouth with water and drink afterwards plenty of water.
Do not give milk or alcoholic beverages.
Never give anything by mouth to an unconscious person.
4.2 Most important symptoms and effects, both acute and delayed
Symptoms : See Section 11 for more detailed information on health effects
and symptoms.
Risks : No known significant effects or hazards.
4.3 Indication of any immediate medical attention and special treatment needed
Treatment : Treat symptomatically.
SECTION 5: Firefighting measures
5.1 Extinguishing media
Suitable extinguishing media : Use extinguishing measures that are appropriate to local cir-
cumstances and the surrounding environment.
5.2 Special hazards arising from the substance or mixture
5.3 Advice for firefighters
Special protective equipment
for firefighters
: In the event of fire, wear self-contained breathing apparatus.
Further information : Standard procedure for chemical fires.
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 3 / 9
SECTION 6: Accidental release measures
6.1 Personal precautions, protective equipment and emergency procedures
Personal precautions : Avoid dust formation.
6.2 Environmental precautions
Environmental precautions : No special environmental precautions required.
6.3 Methods and materials for containment and cleaning up
Methods for cleaning up : Keep in suitable, closed containers for disposal.
Sweep up or vacuum up spillage and collect in suitable con-
tainer for disposal.
6.4 Reference to other sections
For personal protection see section 8.
SECTION 7: Handling and storage
7.1 Precautions for safe handling
Advice on safe handling : For personal protection see section 8. No special handling
advice required. Follow standard hygiene measures when
handling chemical products
Advice on protection against
fire and explosion
: Avoid dust formation. Provide appropriate exhaust ventilation
at places where dust is formed.
Hygiene measures : General industrial hygiene practice.
7.2 Conditions for safe storage, including any incompatibilities
Requirements for storage
areas and containers
: Keep container tightly closed in a dry and well-ventilated
place. Store in accordance with local regulations.
Advice on common storage : No special restrictions on storage with other products.
Other data : No decomposition if stored and applied as directed.
7.3 Specific end use(s)
Specific use(s) : no data available
SECTION 8: Exposure controls/personal protection
8.1 Control parameters
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 4 / 9
Components with workplace control parameters
Contains no substances with occupational exposure limit values.
8.2 Exposure controls
Personal protective equipment
Eye protection : Safety glasses
Hand protection : Chemical-resistant, impervious gloves complying with an ap-
proved standard must be worn at all times when handling
chemical products. Reference number EN 374. Follow manu-
facturer specifications.
Skin and body protection : Protective clothing (e.g. Safety shoes acc. to EN ISO 20345,
long-sleeved working clothing, long trousers). Rubber aprons
and protective boots are additionaly recommended for mixing
and stirring work.
Respiratory protection : No special measures required.
Environmental exposure controls
General advice : No special environmental precautions required.
SECTION 9: Physical and chemical properties
9.1 Information on basic physical and chemical properties
Appearance : solid
Colour : brown
Odour : characteristic
Odour Threshold : no data available
Flash point : Note: not applicable
Ignition temperature : no data available
Lower explosion limit (Vol%) : no data available
Upper explosion limit (Vol%) : no data available
Flammability (solid, gas) : no data available
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 5 / 9
Oxidizing properties : no data available
Auto-ignition temperature : no data available
pH : Note: not applicable
Melting point/range / Freez-
ing point
: no data available
Boiling point/boiling range : no data available
Vapour pressure : no data available
Density : ca.0,64 g/cm3
at 20 C
Water solubility : Note: insoluble
Partition coefficient: n-
octanol/water
: no data available
Viscosity, dynamic : Note: not applicable
Viscosity, kinematic : Note: not applicable
Relative vapour density : no data available
Evaporation rate : no data available
9.2 Other information
no data available
SECTION 10: Stability and reactivity
10.1 Reactivity
No dangerous reaction known under conditions of normal use.
10.2 Chemical stability
The product is chemically stable.
10.3 Possibility of hazardous reactions
Hazardous reactions : No hazards to be specially mentioned.
Dust may form explosive mixture in air.
10.4 Conditions to avoid
Conditions to avoid : no data available
10.5 Incompatible materials
Materials to avoid : no data available
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 6 / 9
10.6 Hazardous decomposition products
SECTION 11: Toxicological information
11.1 Information on toxicological effects
Acute toxicity
no data available
Skin corrosion/irritation
Product
no data available
Serious eye damage/eye irritation
Product
no data available
Respiratory or skin sensitisation
Product
no data available
Germ cell mutagenicity
Product
Mutagenicity : no data available
Carcinogenicity
Product
Carcinogenicity : no data available
Reproductive Toxicity/Fertility
Reproductive toxicity : no data available
no data available
Reproductive Toxicity/Development/Teratogenicity
Teratogenicity : no data available
no data available
STOT – single exposure
no data available
STOT – repeated exposure
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 7 / 9
no data available
Aspiration toxicity
no data available
SECTION 12: Ecological information
12.1 Toxicity
no data available
12.2 Persistence and degradability
no data available
12.3 Bioaccumulative potential
no data available
12.4 Mobility in soil
no data available
12.5 Results of PBT and vPvB assessment
Product:
Assessment : This substance/mixture contains no components considered
to be either persistent, bioaccumulative and toxic (PBT), or
very persistent and very bioaccumulative (vPvB) at levels of
0.1% or higher.
12.6 Other adverse effects
no data available
SECTION 13: Disposal considerations
13.1 Waste treatment methods
Product : In accordance with the EWC Waste Regulation the classifica-
tion of waste is to be assigned to the jurisdiction of the origin
of waste. Therefore, it is not possible to assign a particular
waste identification number.
Completely emptied packagings may be given for recycling.
Empty packaging may still contain hazardous residues. Empty
packaging should be removed by a licensed waste contractor.
Sika has agreed disposal contracts for all packaging which is
brought into circulation in Germany.
For further details see www.sika.de
SECTION 14: Transport information
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 8 / 9
ADR
Not dangerous goods
IATA
Not dangerous goods
IMDG
Not dangerous goods
14.6 Special precautions for user
no data available
14.7 Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
not applicable
SECTION 15: Regulatory information
15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture
Prohibition/Restriction
REACH – Restrictions on the manufacture, placing on
the market and use of certain dangerous substances,
preparations and articles (Annex XVII)
: not applicable
REACH – Candidate List of Substances of Very High
Concern for Authorisation (Article 59).
: None of the components are listed
(=> 0.1 %).
REACH – List of substances subject to authorisation
(Annex XIV)
: not applicable
REACH Information: All substances contained in our Products are
– preregistered or registered by our upstream suppliers, and/or
– preregistered or registered by us, and/or
– excluded from the regulation, and/or
– exempted from the registration.
Water contaminating class
(Germany)
: nwg not water endangering
Gem VwVws vom 30.Juli 2005
VOC-CH (VOCV) : no VOC duties
VOC-EU (solvent) : not applicable
15.2 Chemical Safety Assessment
This product contains substances for which Chemical Safety Assessments are still required.
SECTION 16: Other information
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 9 / 9
The information contained in this Safety Data Sheet corresponds to our level of knowledge at the
time of publication. All warranties are excluded. Our most current General Sales Conditions shall
apply. Please consult the product data sheet prior to any any use and processing.
Changes as compared to previous version !
by | Sep 27, 2025
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 1 / 9
SECTION 1: Identification of the substance/mixture and of the company/undertaking
1.1 Product identifier
Trade name : SikaBlock M600
1.2 Relevant identified uses of the substance or mixture and uses advised against
At present there is no complete information available on identified uses. When the data becomes
available, it will be integrated into the safety data sheet.
1.3 Details of the supplier of the safety data sheet
Company : Sika Deutschland GmbH
Kornwestheimer Str. 103-107
70439 Stuttgart
Telephone : +4971180090
1.4 Emergency telephone number
Emergency telephone num-
ber
:
0173-6774799 Out of office hours only
EHS@de.sika.com
SECTION 2: Hazards identification
2.1 Classification of the substance or mixture
Type of product : Mixture
Classification (67/548/EEC, 1999/45/EC)
Not a hazardous substance or mixture.
2.2 Label elements
Labelling according to EC Directives: 1999/45/EC
The product does not need to be labelled in accordance with EC directives or respective national
laws.
2.3 Other hazards
This mixture contains no substance considered to be persistent, bioaccumulating nor toxic (PBT).
This mixture contains no substance considered to be very persistent nor very bioaccumulating
(vPvB).
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 2 / 9
SECTION 3: Composition/information on ingredients
3.2 Mixtures
Remarks : No hazardous ingredients
SECTION 4: First aid measures
4.1 Description of first aid measures
General advice : No hazards which require special first aid measures.
If inhaled : If symptoms persist, call a physician.
In case of skin contact : Take off contaminated clothing and shoes immediately.
Wash off with soap and plenty of water.
In case of eye contact : Flush eyes with water as a precaution.
Remove contact lenses.
Keep eye wide open while rinsing.
If swallowed : Clean mouth with water and drink afterwards plenty of water.
Do not give milk or alcoholic beverages.
Never give anything by mouth to an unconscious person.
4.2 Most important symptoms and effects, both acute and delayed
Symptoms : See Section 11 for more detailed information on health effects
and symptoms.
Risks : No known significant effects or hazards.
4.3 Indication of any immediate medical attention and special treatment needed
Treatment : Treat symptomatically.
SECTION 5: Firefighting measures
5.1 Extinguishing media
Suitable extinguishing media : Use extinguishing measures that are appropriate to local cir-
cumstances and the surrounding environment.
5.2 Special hazards arising from the substance or mixture
5.3 Advice for firefighters
Special protective equipment
for firefighters
: In the event of fire, wear self-contained breathing apparatus.
Further information : Standard procedure for chemical fires.
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 3 / 9
SECTION 6: Accidental release measures
6.1 Personal precautions, protective equipment and emergency procedures
Personal precautions : Avoid dust formation.
6.2 Environmental precautions
Environmental precautions : No special environmental precautions required.
6.3 Methods and materials for containment and cleaning up
Methods for cleaning up : Keep in suitable, closed containers for disposal.
Sweep up or vacuum up spillage and collect in suitable con-
tainer for disposal.
6.4 Reference to other sections
For personal protection see section 8.
SECTION 7: Handling and storage
7.1 Precautions for safe handling
Advice on safe handling : For personal protection see section 8. No special handling
advice required. Follow standard hygiene measures when
handling chemical products
Advice on protection against
fire and explosion
: Avoid dust formation. Provide appropriate exhaust ventilation
at places where dust is formed.
Hygiene measures : General industrial hygiene practice.
7.2 Conditions for safe storage, including any incompatibilities
Requirements for storage
areas and containers
: Keep container tightly closed in a dry and well-ventilated
place. Store in accordance with local regulations.
Advice on common storage : No special restrictions on storage with other products.
Other data : No decomposition if stored and applied as directed.
7.3 Specific end use(s)
Specific use(s) : no data available
SECTION 8: Exposure controls/personal protection
8.1 Control parameters
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 4 / 9
Components with workplace control parameters
Contains no substances with occupational exposure limit values.
8.2 Exposure controls
Personal protective equipment
Eye protection : Safety glasses
Hand protection : Chemical-resistant, impervious gloves complying with an ap-
proved standard must be worn at all times when handling
chemical products. Reference number EN 374. Follow manu-
facturer specifications.
Skin and body protection : Protective clothing (e.g. Safety shoes acc. to EN ISO 20345,
long-sleeved working clothing, long trousers). Rubber aprons
and protective boots are additionaly recommended for mixing
and stirring work.
Respiratory protection : No special measures required.
Environmental exposure controls
General advice : No special environmental precautions required.
SECTION 9: Physical and chemical properties
9.1 Information on basic physical and chemical properties
Appearance : solid
Colour : brown
Odour : characteristic
Odour Threshold : no data available
Flash point : Note: not applicable
Ignition temperature : no data available
Lower explosion limit (Vol%) : no data available
Upper explosion limit (Vol%) : no data available
Flammability (solid, gas) : no data available
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 5 / 9
Oxidizing properties : no data available
Auto-ignition temperature : no data available
pH : Note: not applicable
Melting point/range / Freez-
ing point
: no data available
Boiling point/boiling range : no data available
Vapour pressure : no data available
Density : ca.0,64 g/cm3
at 20 C
Water solubility : Note: insoluble
Partition coefficient: n-
octanol/water
: no data available
Viscosity, dynamic : Note: not applicable
Viscosity, kinematic : Note: not applicable
Relative vapour density : no data available
Evaporation rate : no data available
9.2 Other information
no data available
SECTION 10: Stability and reactivity
10.1 Reactivity
No dangerous reaction known under conditions of normal use.
10.2 Chemical stability
The product is chemically stable.
10.3 Possibility of hazardous reactions
Hazardous reactions : No hazards to be specially mentioned.
Dust may form explosive mixture in air.
10.4 Conditions to avoid
Conditions to avoid : no data available
10.5 Incompatible materials
Materials to avoid : no data available
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 6 / 9
10.6 Hazardous decomposition products
SECTION 11: Toxicological information
11.1 Information on toxicological effects
Acute toxicity
no data available
Skin corrosion/irritation
Product
no data available
Serious eye damage/eye irritation
Product
no data available
Respiratory or skin sensitisation
Product
no data available
Germ cell mutagenicity
Product
Mutagenicity : no data available
Carcinogenicity
Product
Carcinogenicity : no data available
Reproductive Toxicity/Fertility
Reproductive toxicity : no data available
no data available
Reproductive Toxicity/Development/Teratogenicity
Teratogenicity : no data available
no data available
STOT – single exposure
no data available
STOT – repeated exposure
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 7 / 9
no data available
Aspiration toxicity
no data available
SECTION 12: Ecological information
12.1 Toxicity
no data available
12.2 Persistence and degradability
no data available
12.3 Bioaccumulative potential
no data available
12.4 Mobility in soil
no data available
12.5 Results of PBT and vPvB assessment
Product:
Assessment : This substance/mixture contains no components considered
to be either persistent, bioaccumulative and toxic (PBT), or
very persistent and very bioaccumulative (vPvB) at levels of
0.1% or higher.
12.6 Other adverse effects
no data available
SECTION 13: Disposal considerations
13.1 Waste treatment methods
Product : In accordance with the EWC Waste Regulation the classifica-
tion of waste is to be assigned to the jurisdiction of the origin
of waste. Therefore, it is not possible to assign a particular
waste identification number.
Completely emptied packagings may be given for recycling.
Empty packaging may still contain hazardous residues. Empty
packaging should be removed by a licensed waste contractor.
Sika has agreed disposal contracts for all packaging which is
brought into circulation in Germany.
For further details see www.sika.de
SECTION 14: Transport information
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 8 / 9
ADR
Not dangerous goods
IATA
Not dangerous goods
IMDG
Not dangerous goods
14.6 Special precautions for user
no data available
14.7 Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
not applicable
SECTION 15: Regulatory information
15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture
Prohibition/Restriction
REACH – Restrictions on the manufacture, placing on
the market and use of certain dangerous substances,
preparations and articles (Annex XVII)
: not applicable
REACH – Candidate List of Substances of Very High
Concern for Authorisation (Article 59).
: None of the components are listed
(=> 0.1 %).
REACH – List of substances subject to authorisation
(Annex XIV)
: not applicable
REACH Information: All substances contained in our Products are
– preregistered or registered by our upstream suppliers, and/or
– preregistered or registered by us, and/or
– excluded from the regulation, and/or
– exempted from the registration.
Water contaminating class
(Germany)
: nwg not water endangering
Gem VwVws vom 30.Juli 2005
VOC-CH (VOCV) : no VOC duties
VOC-EU (solvent) : not applicable
15.2 Chemical Safety Assessment
This product contains substances for which Chemical Safety Assessments are still required.
SECTION 16: Other information
SAFETY DATA SHEET
according to Regulation (EC) No. 1907/2006
SikaBlock M600
Revision Date 15.11.2013 Print Date 25.06.2015
Country DE 100000004766 9 / 9
The information contained in this Safety Data Sheet corresponds to our level of knowledge at the
time of publication. All warranties are excluded. Our most current General Sales Conditions shall
apply. Please consult the product data sheet prior to any any use and processing.
Changes as compared to previous version !
by | Sep 27, 2025
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 1: IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKING
1.1Product identifier: BP850 – Polyurethane Tooling Board
Other means of identification:
Non-applicable
1.2Relevant identified uses of the substance or mixture and uses advised against:
Relevant uses: Non Hazardous Substance . For industrial user only.
Uses advised against: All uses not specified in this section or in section 7.3
1.3Details of the supplier of the safety data sheet:
Base Materials
Base Materials Ltd,20 Ashville Way
LE8 6NU Leicester – Whetstone – United Kingdom
Phone: 0116 286 5073
sales@base-materials.com
https://www.base-materials.com/
1.4Emergency telephone number: Ecostar Environmental – Reference Code: EREF-00111 : Telephone: +44 800
246 1972 (office hours), WhatsApp: +44 7496 228 905 (office hours), 24/7
Service +44 800 246 1274
SECTION 2: HAZARDS IDENTIFICATION
2.1Classification of the substance or mixture:
When milling: Dust will be produced
GB CLP Regulation:
The product is not classified as hazardous according to GB CLP Regulation.
2.2Label elements:
Metals in massive form, alloys, mixtures containing polymers and mixtures containing elastomers do not require
a label if they do not present a hazard to human health by inhalation, ingestion or contact with skin or to the
aquatic environment in the form in which they are placed on the market, although classified as hazardous.
GB CLP Regulation:
None
2.3Other hazards:
Product does not meet PBT/vPvB criteria
SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS
3.1Substance:
Non-applicable
3.2Mixture:
Chemical description: elastomeric matrix
Components:
None of the substances contained in the mixture are above the values fixed in Annex II of The REACH etc.
(Amendment etc.) (EU Exit) Regulations 2020.
Reaction product based on polyurethane
SECTION 4: FIRST AID MEASURES
4.1Description of first aid measures:
Consult a doctor in case of discomfort showing the SDS for the product.
By inhalation:
The possibility of being inhaled is practically nil, however, in the case of symptoms:
In case of symptoms, move the person affected into fresh air.
By skin contact:
– CONTINUED ON NEXT PAGE –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 1/8
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 4: FIRST AID MEASURES (continued)
In case of contact it is recommended to clean the affected area thoroughly with water and neutral soap. In case
of changes to the skin (stinging, redness, rashes, blisters, ), seek medical advice with this Safety Data Sheet
By eye contact:
Rinse with water until the product has been eliminated. In case of problems, consult a doctor showing the SDS
for the product.
By ingestion/aspiration:
In case of consumption in large quantities, it is recommended to seek medical assistance.
Dust: Provide fresh air.
4.2Most important symptoms and effects, both acute and delayed:
Acute and delayed effects are indicated in sections 2 and 11.
4.3Indication of any immediate medical attention and special treatment needed:
Non-applicable
SECTION 5: FIREFIGHTING MEASURES
5.1Extinguishing media:
Suitable extinguishing media:
Product is non-flammable, with a low risk of fire due to the flammability characteristics of the product in normal
conditions of storage, handling and use. In the case of the existence of sustained combustion as a result of
improper handling, storage or use any type of extinguishing agent can be used (ABC Powder, water,…)
Unsuitable extinguishing media:
Non-applicable
5.2Special hazards arising from the substance or mixture:
Due to its non-inflammable nature, the product does not present a fire risk under normal conditions of storage,
handling and use.
5.3Advice for firefighters:
Depending on the magnitude of the fire it may be necessary to use full protective clothing and self-contained
breathing apparatus (SCBA). Minimum emergency facilities and equipment should be available (fire blankets,
portable first aid kit,…).
Additional provisions:
Act in accordance with the Internal Emergency Plan and the Information Sheets on actions to take after an
accident or other emergencies. Eliminate all sources of ignition. In case of fire, cool the storage containers and
tanks for products susceptible to combustion, explosion or BLEVE as a result of high temperatures. Avoid spillage
of the products used to extinguish the fire into an aqueous medium.
SECTION 6: ACCIDENTAL RELEASE MEASURES
6.1Personal precautions, protective equipment and emergency procedures:
For non-emergency personnel:
Sweep up and shovel product or collect by other means and place in container for reuse (preferred) or disposal
For emergency responders:
Wear protective equipment. Keep unprotected persons away. See section 8.
Other information:
May form combustible dust concentrations in air. Keep away from sources of ignition – No smoking.
6.2Environmental precautions:
This product is not classified as hazardous to the environment. Keep product away from drains, surface and
ground water.
6.3Methods and material for containment and cleaning up:
It is recommended:
Sweep up and shovel product or collect by other means and place in container for reuse (preferred) or disposal
6.4Reference to other sections:
– CONTINUED ON NEXT PAGE –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 2/8
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 6: ACCIDENTAL RELEASE MEASURES (continued)
See sections 8 and 13.
SECTION 7: HANDLING AND STORAGE
7.1Precautions for safe handling:
A.-General precautions for safe use
Comply with the current legislation concerning the prevention of industrial risks with regards manually
handling weights. Maintain order, cleanliness and dispose of using safe methods (section 6).
B.-Technical recommendations for the prevention of fires and explosions
Due to its non-inflammable nature, the product does not present a fire risk under normal conditions of
storage, handling and use.
C.-Technical recommendations on general occupational hygiene
Do not eat or drink during the process, washing hands afterwards with suitable cleaning products.
D.-Technical recommendations to prevent environmental risks
It is not necessary to take special measures to prevent environmental risks. For more information see
subsection 6.2
Other information:
May form combustible dust concentrations in air. Keep away from sources of ignition – No smoking.
7.2Conditions for safe storage, including any incompatibilities:
A.-Technical measures for storage
Store in a cool, dry, well-ventilated location
B.-General conditions for storage
Avoid sources of heat, radiation, static electricity and contact with food. For additional information see
subsection 10.5
7.3Specific end use(s):
Except for the instructions already specified it is not necessary to provide any special recommendation regarding
the uses of this product.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1Control parameters:
Substances whose occupational exposure limits have to be monitored in the workplace:
Nuisance dust: Inhalable dust 10 mg/m3 // Respirable dust 4 mg/m3
DNEL (Workers):
Non-applicable
DNEL (General population):
Non-applicable
PNEC:
Non-applicable
8.2Exposure controls:
A.-Individual protection measures, such as personal protective equipment
As a preventative measure it is recommended to use basic Personal Protective Equipment, with the
corresponding <>. For more information on Personal Protective Equipment (storage, use,
cleaning, maintenance, class of protection, ) consult the information leaflet provided by the manufacturer. For
more information see subsection 7.1. All information contained herein is a recommendation which needs
some specification from the labour risk prevention services as it is not known whether the company has
additional measures at its disposal.
B.-Respiratory protection
The use of protection equipment will be necessary if a mist forms or if the occupational exposure limits are
exceeded.
C.-Specific protection for the hands
– CONTINUED ON NEXT PAGE –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 3/8
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION (continued)
Pictogram PPE Remarks
Mandatory hand
protection
Protective gloves against minor risks
Replace gloves in case of any sign of damage. For prolonged periods of
exposure to the product for professional users/industrials, we
recommend using CE III gloves in line with standards EN ISO
21420:2020 and EN ISO 374-1:2016+A1:2018
As the product is a mixture of several substances, the resistance of the glove material can not be calculated in
advance with total reliability and has therefore to be checked prior to the application.
D.-Eye and face protection
Pictogram PPE Remarks
Mandatory face
protection
Panoramic glasses against
splash/projections.
Clean daily and disinfect periodically according to the manufacturer s
instructions. Use if there is a risk of splashing.
E.-Body protection
Pictogram PPE Remarks
Work clothing
Replace before any evidence of deterioration. For periods of prolonged
exposure to the product for professional/industrial users CE III is
recommended, in accordance with the regulations in EN ISO 6529:2013,
EN ISO 6530:2005, EN ISO 13688:2013, EN 464:1994.
Anti-slip work shoes
Replace before any evidence of deterioration. For periods of prolonged
exposure to the product for professional/industrial users CE III is
recommended, in accordance with the regulations in EN ISO
20345:2012 y EN 13832-1:2007
F.-Additional emergency measures
It is not necessary to take additional emergency measures.
Environmental exposure controls:
In accordance with the community legislation for the protection of the environment it is recommended to avoid
environmental spillage of both the product and its container. For additional information see subsection 7.1.D
The Volatile Organic Compounds in Paints, Varnishes and Vehicle Refinishing Products Regulations
2012:
V.O.C. (Supply): 0 % weight
V.O.C. density at 20 C: 0 kg/m (0 g/L)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
9.1Information on basic physical and chemical properties:
For complete information see the product datasheet.
Appearance:
Physical state at 20 C: Solid
Appearance: Not available
Colour: Grey
Odour: Not available
Odour threshold: Non-applicable *
Volatility:
Boiling point at atmospheric pressure: Non-applicable *
Vapour pressure at 20 C: Non-applicable *
Vapour pressure at 50 C: Non-applicable *
Evaporation rate at 20 C: Non-applicable *
*Not relevant due to the nature of the product, not providing information property of its hazards.
– CONTINUED ON NEXT PAGE –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 4/8
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES (continued)
Product description:
Density at 20 C: ca. 850 kg/m
Relative density at 20 C: ca. 0.85
Dynamic viscosity at 20 C: Non-applicable *
Kinematic viscosity at 20 C: Non-applicable *
Kinematic viscosity at 40 C: Non-applicable *
Concentration: Non-applicable *
pH: Non-applicable *
Vapour density at 20 C: Non-applicable *
Partition coefficient n-octanol/water 20 C: Non-applicable *
Solubility in water at 20 C: Non-applicable *
Solubility properties: Non-applicable *
Decomposition temperature: Non-applicable *
Melting point/freezing point: Non-applicable *
Flammability:
Flash Point: Non-applicable
Flammability (solid, gas): Non-applicable *
Autoignition temperature: Non-applicable *
Lower flammability limit: Non-applicable *
Upper flammability limit: Non-applicable *
Explosive (Solid):
Lower explosive limit: Non-applicable *
Upper explosive limit: Non-applicable *
Particle characteristics:
Median equivalent diameter: Non-applicable *
9.2Other information:
Information with regard to physical hazard classes:
Explosive properties: Non-applicable *
Oxidising properties: Non-applicable *
Corrosive to metals: Non-applicable *
Heat of combustion: Non-applicable *
Aerosols-total percentage (by mass) of
flammable components:
Non-applicable *
Other safety characteristics:
Surface tension at 20 C: Non-applicable *
Refraction index: Non-applicable *
*Not relevant due to the nature of the product, not providing information property of its hazards.
SECTION 10: STABILITY AND REACTIVITY
10.1Reactivity:
No hazardous reactions are expected because the product is stable under recommended storage conditions. See
section 7 from Safety Data Sheet.
10.2Chemical stability:
Chemically stable under the indicated conditions of storage, handling and use.
10.3Possibility of hazardous reactions:
Under the specified conditions, hazardous reactions that lead to excessive temperatures or pressure are not
expected.
– CONTINUED ON NEXT PAGE –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 5/8
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 10: STABILITY AND REACTIVITY (continued)
10.4Conditions to avoid:
Applicable for handling and storage at room temperature:
Shock and friction Contact with air Increase in temperature Sunlight Humidity
Not applicable Not applicable Not applicable Not applicable Not applicable
10.5Incompatible materials:
Acids Water Oxidising materials Combustible materials Others
Avoid strong acids Not applicable Not applicable Not applicable
Avoid alkalis or strong
bases
10.6Hazardous decomposition products:
See subsection 10.3, 10.4 and 10.5 to find out the specific decomposition products. Depending on the
decomposition conditions, complex mixtures of chemical substances can be released: carbon dioxide (CO ),
carbon monoxide and other organic compounds.
SECTION 11: TOXICOLOGICAL INFORMATION
11.1Information on toxicological effects:
LD50 oral > 2000 mg/kg (rat)
Dangerous health implications:
In case of exposure that is repetitive, prolonged or at concentrations higher than the recommended occupational
exposure limits, adverse effects on health may result, depending on the means of exposure:
A-Ingestion (acute effect):
– Acute toxicity: Based on available data, the classification criteria are not met
– Corrosivity/Irritability: Based on available data, the classification criteria are not met
B-Inhalation (acute effect):
It is advised that, due to the encapsulation of the active ingredient, it is estimated that inhalation hazards
could be minimized. This criterion applies throughout the entire SDS.
– Acute toxicity : Based on available data, the classification criteria are not met
– Corrosivity/Irritability: Based on available data, the classification criteria are not met
C-Contact with the skin and the eyes (acute effect):
– Contact with the skin: Based on available data, the classification criteria are not met
– Contact with the eyes: Based on available data, the classification criteria are not met
D-CMR effects (carcinogenicity, mutagenicity and toxicity to reproduction):
– Carcinogenicity: Based on available data, the classification criteria are not met
IARC: Non-applicable
– Mutagenicity: Based on available data, the classification criteria are not met
– Reproductive toxicity: Based on available data, the classification criteria are not met
E-Sensitizing effects:
– Respiratory: Based on available data, the classification criteria are not met
– Skin: Based on available data, the classification criteria are not met
F-Specific target organ toxicity (STOT) – single exposure:
Based on available data, the classification criteria are not met
G-Specific target organ toxicity (STOT)-repeated exposure:
– Specific target organ toxicity (STOT)-repeated exposure: Based on available data, the classification criteria
are not met
– Skin: Based on available data, the classification criteria are not met, as it does not contain substances
classified as hazardous for this effect. For more information see section 3.
H-Aspiration hazard:
Based on available data, the classification criteria are not met
Other information:
Non-applicable
– CONTINUED ON NEXT PAGE –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 6/8
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 11: TOXICOLOGICAL INFORMATION (continued)
Specific toxicology information on the substances:
Not available
SECTION 12: ECOLOGICAL INFORMATION
The experimental information related to the eco-toxicological properties of the product itself is not available
Based on available data, the classification criteria are not met
12.1Toxicity:
Not available
12.2Persistence and degradability:
Not available
12.3Bioaccumulative potential:
Not available
12.4Mobility in soil:
Not available
12.5Results of PBT and vPvB assessment:
Product does not meet PBT/vPvB criteria
12.6Other adverse effects:
Not described
SECTION 13: DISPOSAL CONSIDERATIONS
13.1Waste treatment methods:
Code Description Waste class
16 03 06 organic wastes other than those mentioned in 16 03 05 Non dangerous
Type of waste:
Non-applicable
Waste management (disposal and evaluation):
Consult the authorized waste service manager on the assessment and disposal operations in accordance The
Waste Regulations 2011, 2011 No. 988. As under 15 01 of the code and in case the container has been in direct
contact with the product, it will be processed the same way as the actual product. Otherwise, it will be processed
as non-dangerous residue. Waste should not be disposed of to drains. See paragraph 6.2.
Regulations related to waste management:
In accordance with Annex II of UK REACH the provisions related to waste management are stated:
UK legislation: The Waste Regulations 2011.
SECTION 14: TRANSPORT INFORMATION
This product is not regulated for transport (ADR/RID,IMDG,IATA)
SECTION 15: REGULATORY INFORMATION
15.1Safety, health and environmental regulations/legislation specific for the substance or mixture:
– Substances listed in UK candidate list of substances of very high concern (SVHCs): Non-applicable
– Substances listed in UK REACH Authorisation List (Annex 14): Non-applicable
The Control of Major Accident Hazards Regulations 2015:
Non-applicable
– CONTINUED ON NEXT PAGE –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 7/8
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 15: REGULATORY INFORMATION (continued)
Restrictions to commercialisation and the use of certain dangerous substances and mixtures (Annex
XVII UK REACH, etc .):
Non-applicable
Specific provisions in terms of protecting people or the environment:
It is recommended to use the information included in this safety data sheet as a basis for conducting workplace-
specific risk assessments in order to establish the necessary risk prevention measures for the handling, use,
storage and disposal of this product.
Other legislation:
The REACH etc. (Amendment etc.) (EU Exit) Regulations 2020.
The Chemicals (Health and Safety) and Genetically Modified Organisms (Contained Use) (Amendment etc.) (EU
Exit) Regulations 2020.
Control of Substances Hazardous to Health Regulations 2002 (as amended)
EH40/2005 Workplace exposure limits.
SECTION 16: OTHER INFORMATION
Legislation related to safety data sheets:
This safety data sheet has been designed in accordance with ANNEX II-The REACH etc. (Amendment etc.) (EU
Exit) Regulations 2020.
Texts of the legislative phrases mentioned in section 3:
The phrases indicated do not refer to the product itself; they are present merely for informative purposes and
refer to the individual components which appear in section 3
GB CLP Regulation:
Non-applicable
Classification procedure:
Non-applicable
Advice related to training:
Training is recommended in order to prevent industrial risks for staff using this product and to facilitate their
comprehension and interpretation of this safety data sheet, as well as the label on the product.
Principal bibliographical sources:
http://echa.europa.eu
http://eur-lex.europa.eu
Abbreviations and acronyms:
ADR: European agreement concerning the international carriage of dangerous goods by road
IMDG: International maritime dangerous goods code
IATA: International Air Transport Association
ICAO: International Civil Aviation Organisation
COD: Chemical Oxygen Demand
BOD5: 5day biochemical oxygen demand
BCF: Bioconcentration factor
LD50: Lethal Dose 50
LC50: Lethal Concentration 50
EC50: Effective concentration 50
LogPOW: Octanolwater partition coefficient
Koc: Partition coefficient of organic carbon
UFI: unique formula identifier
IARC: International Agency for Research on Cancer
Theinformationcontainedinthissafetydatasheetisbasedonsources,technicalknowledgeandcurrentlegislationatUK,withoutbeingabletoguaranteeitsaccuracy.
Thisinformationcannotbeconsideredaguaranteeofthepropertiesoftheproduct,itissimplyadescriptionofthesecurityrequirements.Theoccupationalmethodology
andconditionsforusersofthisproductarenotwithinourawarenessorcontrol,anditisultimatelytheresponsibilityoftheusertotakethenecessarymeasurestoobtain
thelegalrequirementsconcerningthemanipulation,storage,useanddisposalofchemicalproducts.Theinformationonthissafetydatasheetonlyreferstothisproduct,
whichshouldnotbeusedforneedsotherthanthosespecified.
– END OF SAFETY DATA SHEET –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 8/8
by | Sep 27, 2025
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 1: IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKING
1.1Product identifier: BP850 – Polyurethane Tooling Board
Other means of identification:
Non-applicable
1.2Relevant identified uses of the substance or mixture and uses advised against:
Relevant uses: Non Hazardous Substance . For industrial user only.
Uses advised against: All uses not specified in this section or in section 7.3
1.3Details of the supplier of the safety data sheet:
Base Materials
Base Materials Ltd,20 Ashville Way
LE8 6NU Leicester – Whetstone – United Kingdom
Phone: 0116 286 5073
sales@base-materials.com
https://www.base-materials.com/
1.4Emergency telephone number: Ecostar Environmental – Reference Code: EREF-00111 : Telephone: +44 800
246 1972 (office hours), WhatsApp: +44 7496 228 905 (office hours), 24/7
Service +44 800 246 1274
SECTION 2: HAZARDS IDENTIFICATION
2.1Classification of the substance or mixture:
When milling: Dust will be produced
GB CLP Regulation:
The product is not classified as hazardous according to GB CLP Regulation.
2.2Label elements:
Metals in massive form, alloys, mixtures containing polymers and mixtures containing elastomers do not require
a label if they do not present a hazard to human health by inhalation, ingestion or contact with skin or to the
aquatic environment in the form in which they are placed on the market, although classified as hazardous.
GB CLP Regulation:
None
2.3Other hazards:
Product does not meet PBT/vPvB criteria
SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS
3.1Substance:
Non-applicable
3.2Mixture:
Chemical description: elastomeric matrix
Components:
None of the substances contained in the mixture are above the values fixed in Annex II of The REACH etc.
(Amendment etc.) (EU Exit) Regulations 2020.
Reaction product based on polyurethane
SECTION 4: FIRST AID MEASURES
4.1Description of first aid measures:
Consult a doctor in case of discomfort showing the SDS for the product.
By inhalation:
The possibility of being inhaled is practically nil, however, in the case of symptoms:
In case of symptoms, move the person affected into fresh air.
By skin contact:
– CONTINUED ON NEXT PAGE –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 1/8
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 4: FIRST AID MEASURES (continued)
In case of contact it is recommended to clean the affected area thoroughly with water and neutral soap. In case
of changes to the skin (stinging, redness, rashes, blisters, ), seek medical advice with this Safety Data Sheet
By eye contact:
Rinse with water until the product has been eliminated. In case of problems, consult a doctor showing the SDS
for the product.
By ingestion/aspiration:
In case of consumption in large quantities, it is recommended to seek medical assistance.
Dust: Provide fresh air.
4.2Most important symptoms and effects, both acute and delayed:
Acute and delayed effects are indicated in sections 2 and 11.
4.3Indication of any immediate medical attention and special treatment needed:
Non-applicable
SECTION 5: FIREFIGHTING MEASURES
5.1Extinguishing media:
Suitable extinguishing media:
Product is non-flammable, with a low risk of fire due to the flammability characteristics of the product in normal
conditions of storage, handling and use. In the case of the existence of sustained combustion as a result of
improper handling, storage or use any type of extinguishing agent can be used (ABC Powder, water,…)
Unsuitable extinguishing media:
Non-applicable
5.2Special hazards arising from the substance or mixture:
Due to its non-inflammable nature, the product does not present a fire risk under normal conditions of storage,
handling and use.
5.3Advice for firefighters:
Depending on the magnitude of the fire it may be necessary to use full protective clothing and self-contained
breathing apparatus (SCBA). Minimum emergency facilities and equipment should be available (fire blankets,
portable first aid kit,…).
Additional provisions:
Act in accordance with the Internal Emergency Plan and the Information Sheets on actions to take after an
accident or other emergencies. Eliminate all sources of ignition. In case of fire, cool the storage containers and
tanks for products susceptible to combustion, explosion or BLEVE as a result of high temperatures. Avoid spillage
of the products used to extinguish the fire into an aqueous medium.
SECTION 6: ACCIDENTAL RELEASE MEASURES
6.1Personal precautions, protective equipment and emergency procedures:
For non-emergency personnel:
Sweep up and shovel product or collect by other means and place in container for reuse (preferred) or disposal
For emergency responders:
Wear protective equipment. Keep unprotected persons away. See section 8.
Other information:
May form combustible dust concentrations in air. Keep away from sources of ignition – No smoking.
6.2Environmental precautions:
This product is not classified as hazardous to the environment. Keep product away from drains, surface and
ground water.
6.3Methods and material for containment and cleaning up:
It is recommended:
Sweep up and shovel product or collect by other means and place in container for reuse (preferred) or disposal
6.4Reference to other sections:
– CONTINUED ON NEXT PAGE –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 2/8
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 6: ACCIDENTAL RELEASE MEASURES (continued)
See sections 8 and 13.
SECTION 7: HANDLING AND STORAGE
7.1Precautions for safe handling:
A.-General precautions for safe use
Comply with the current legislation concerning the prevention of industrial risks with regards manually
handling weights. Maintain order, cleanliness and dispose of using safe methods (section 6).
B.-Technical recommendations for the prevention of fires and explosions
Due to its non-inflammable nature, the product does not present a fire risk under normal conditions of
storage, handling and use.
C.-Technical recommendations on general occupational hygiene
Do not eat or drink during the process, washing hands afterwards with suitable cleaning products.
D.-Technical recommendations to prevent environmental risks
It is not necessary to take special measures to prevent environmental risks. For more information see
subsection 6.2
Other information:
May form combustible dust concentrations in air. Keep away from sources of ignition – No smoking.
7.2Conditions for safe storage, including any incompatibilities:
A.-Technical measures for storage
Store in a cool, dry, well-ventilated location
B.-General conditions for storage
Avoid sources of heat, radiation, static electricity and contact with food. For additional information see
subsection 10.5
7.3Specific end use(s):
Except for the instructions already specified it is not necessary to provide any special recommendation regarding
the uses of this product.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1Control parameters:
Substances whose occupational exposure limits have to be monitored in the workplace:
Nuisance dust: Inhalable dust 10 mg/m3 // Respirable dust 4 mg/m3
DNEL (Workers):
Non-applicable
DNEL (General population):
Non-applicable
PNEC:
Non-applicable
8.2Exposure controls:
A.-Individual protection measures, such as personal protective equipment
As a preventative measure it is recommended to use basic Personal Protective Equipment, with the
corresponding <>. For more information on Personal Protective Equipment (storage, use,
cleaning, maintenance, class of protection, ) consult the information leaflet provided by the manufacturer. For
more information see subsection 7.1. All information contained herein is a recommendation which needs
some specification from the labour risk prevention services as it is not known whether the company has
additional measures at its disposal.
B.-Respiratory protection
The use of protection equipment will be necessary if a mist forms or if the occupational exposure limits are
exceeded.
C.-Specific protection for the hands
– CONTINUED ON NEXT PAGE –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 3/8
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION (continued)
Pictogram PPE Remarks
Mandatory hand
protection
Protective gloves against minor risks
Replace gloves in case of any sign of damage. For prolonged periods of
exposure to the product for professional users/industrials, we
recommend using CE III gloves in line with standards EN ISO
21420:2020 and EN ISO 374-1:2016+A1:2018
As the product is a mixture of several substances, the resistance of the glove material can not be calculated in
advance with total reliability and has therefore to be checked prior to the application.
D.-Eye and face protection
Pictogram PPE Remarks
Mandatory face
protection
Panoramic glasses against
splash/projections.
Clean daily and disinfect periodically according to the manufacturer s
instructions. Use if there is a risk of splashing.
E.-Body protection
Pictogram PPE Remarks
Work clothing
Replace before any evidence of deterioration. For periods of prolonged
exposure to the product for professional/industrial users CE III is
recommended, in accordance with the regulations in EN ISO 6529:2013,
EN ISO 6530:2005, EN ISO 13688:2013, EN 464:1994.
Anti-slip work shoes
Replace before any evidence of deterioration. For periods of prolonged
exposure to the product for professional/industrial users CE III is
recommended, in accordance with the regulations in EN ISO
20345:2012 y EN 13832-1:2007
F.-Additional emergency measures
It is not necessary to take additional emergency measures.
Environmental exposure controls:
In accordance with the community legislation for the protection of the environment it is recommended to avoid
environmental spillage of both the product and its container. For additional information see subsection 7.1.D
The Volatile Organic Compounds in Paints, Varnishes and Vehicle Refinishing Products Regulations
2012:
V.O.C. (Supply): 0 % weight
V.O.C. density at 20 C: 0 kg/m (0 g/L)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
9.1Information on basic physical and chemical properties:
For complete information see the product datasheet.
Appearance:
Physical state at 20 C: Solid
Appearance: Not available
Colour: Grey
Odour: Not available
Odour threshold: Non-applicable *
Volatility:
Boiling point at atmospheric pressure: Non-applicable *
Vapour pressure at 20 C: Non-applicable *
Vapour pressure at 50 C: Non-applicable *
Evaporation rate at 20 C: Non-applicable *
*Not relevant due to the nature of the product, not providing information property of its hazards.
– CONTINUED ON NEXT PAGE –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 4/8
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES (continued)
Product description:
Density at 20 C: ca. 850 kg/m
Relative density at 20 C: ca. 0.85
Dynamic viscosity at 20 C: Non-applicable *
Kinematic viscosity at 20 C: Non-applicable *
Kinematic viscosity at 40 C: Non-applicable *
Concentration: Non-applicable *
pH: Non-applicable *
Vapour density at 20 C: Non-applicable *
Partition coefficient n-octanol/water 20 C: Non-applicable *
Solubility in water at 20 C: Non-applicable *
Solubility properties: Non-applicable *
Decomposition temperature: Non-applicable *
Melting point/freezing point: Non-applicable *
Flammability:
Flash Point: Non-applicable
Flammability (solid, gas): Non-applicable *
Autoignition temperature: Non-applicable *
Lower flammability limit: Non-applicable *
Upper flammability limit: Non-applicable *
Explosive (Solid):
Lower explosive limit: Non-applicable *
Upper explosive limit: Non-applicable *
Particle characteristics:
Median equivalent diameter: Non-applicable *
9.2Other information:
Information with regard to physical hazard classes:
Explosive properties: Non-applicable *
Oxidising properties: Non-applicable *
Corrosive to metals: Non-applicable *
Heat of combustion: Non-applicable *
Aerosols-total percentage (by mass) of
flammable components:
Non-applicable *
Other safety characteristics:
Surface tension at 20 C: Non-applicable *
Refraction index: Non-applicable *
*Not relevant due to the nature of the product, not providing information property of its hazards.
SECTION 10: STABILITY AND REACTIVITY
10.1Reactivity:
No hazardous reactions are expected because the product is stable under recommended storage conditions. See
section 7 from Safety Data Sheet.
10.2Chemical stability:
Chemically stable under the indicated conditions of storage, handling and use.
10.3Possibility of hazardous reactions:
Under the specified conditions, hazardous reactions that lead to excessive temperatures or pressure are not
expected.
– CONTINUED ON NEXT PAGE –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 5/8
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 10: STABILITY AND REACTIVITY (continued)
10.4Conditions to avoid:
Applicable for handling and storage at room temperature:
Shock and friction Contact with air Increase in temperature Sunlight Humidity
Not applicable Not applicable Not applicable Not applicable Not applicable
10.5Incompatible materials:
Acids Water Oxidising materials Combustible materials Others
Avoid strong acids Not applicable Not applicable Not applicable
Avoid alkalis or strong
bases
10.6Hazardous decomposition products:
See subsection 10.3, 10.4 and 10.5 to find out the specific decomposition products. Depending on the
decomposition conditions, complex mixtures of chemical substances can be released: carbon dioxide (CO ),
carbon monoxide and other organic compounds.
SECTION 11: TOXICOLOGICAL INFORMATION
11.1Information on toxicological effects:
LD50 oral > 2000 mg/kg (rat)
Dangerous health implications:
In case of exposure that is repetitive, prolonged or at concentrations higher than the recommended occupational
exposure limits, adverse effects on health may result, depending on the means of exposure:
A-Ingestion (acute effect):
– Acute toxicity: Based on available data, the classification criteria are not met
– Corrosivity/Irritability: Based on available data, the classification criteria are not met
B-Inhalation (acute effect):
It is advised that, due to the encapsulation of the active ingredient, it is estimated that inhalation hazards
could be minimized. This criterion applies throughout the entire SDS.
– Acute toxicity : Based on available data, the classification criteria are not met
– Corrosivity/Irritability: Based on available data, the classification criteria are not met
C-Contact with the skin and the eyes (acute effect):
– Contact with the skin: Based on available data, the classification criteria are not met
– Contact with the eyes: Based on available data, the classification criteria are not met
D-CMR effects (carcinogenicity, mutagenicity and toxicity to reproduction):
– Carcinogenicity: Based on available data, the classification criteria are not met
IARC: Non-applicable
– Mutagenicity: Based on available data, the classification criteria are not met
– Reproductive toxicity: Based on available data, the classification criteria are not met
E-Sensitizing effects:
– Respiratory: Based on available data, the classification criteria are not met
– Skin: Based on available data, the classification criteria are not met
F-Specific target organ toxicity (STOT) – single exposure:
Based on available data, the classification criteria are not met
G-Specific target organ toxicity (STOT)-repeated exposure:
– Specific target organ toxicity (STOT)-repeated exposure: Based on available data, the classification criteria
are not met
– Skin: Based on available data, the classification criteria are not met, as it does not contain substances
classified as hazardous for this effect. For more information see section 3.
H-Aspiration hazard:
Based on available data, the classification criteria are not met
Other information:
Non-applicable
– CONTINUED ON NEXT PAGE –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 6/8
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 11: TOXICOLOGICAL INFORMATION (continued)
Specific toxicology information on the substances:
Not available
SECTION 12: ECOLOGICAL INFORMATION
The experimental information related to the eco-toxicological properties of the product itself is not available
Based on available data, the classification criteria are not met
12.1Toxicity:
Not available
12.2Persistence and degradability:
Not available
12.3Bioaccumulative potential:
Not available
12.4Mobility in soil:
Not available
12.5Results of PBT and vPvB assessment:
Product does not meet PBT/vPvB criteria
12.6Other adverse effects:
Not described
SECTION 13: DISPOSAL CONSIDERATIONS
13.1Waste treatment methods:
Code Description Waste class
16 03 06 organic wastes other than those mentioned in 16 03 05 Non dangerous
Type of waste:
Non-applicable
Waste management (disposal and evaluation):
Consult the authorized waste service manager on the assessment and disposal operations in accordance The
Waste Regulations 2011, 2011 No. 988. As under 15 01 of the code and in case the container has been in direct
contact with the product, it will be processed the same way as the actual product. Otherwise, it will be processed
as non-dangerous residue. Waste should not be disposed of to drains. See paragraph 6.2.
Regulations related to waste management:
In accordance with Annex II of UK REACH the provisions related to waste management are stated:
UK legislation: The Waste Regulations 2011.
SECTION 14: TRANSPORT INFORMATION
This product is not regulated for transport (ADR/RID,IMDG,IATA)
SECTION 15: REGULATORY INFORMATION
15.1Safety, health and environmental regulations/legislation specific for the substance or mixture:
– Substances listed in UK candidate list of substances of very high concern (SVHCs): Non-applicable
– Substances listed in UK REACH Authorisation List (Annex 14): Non-applicable
The Control of Major Accident Hazards Regulations 2015:
Non-applicable
– CONTINUED ON NEXT PAGE –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 7/8
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 15: REGULATORY INFORMATION (continued)
Restrictions to commercialisation and the use of certain dangerous substances and mixtures (Annex
XVII UK REACH, etc .):
Non-applicable
Specific provisions in terms of protecting people or the environment:
It is recommended to use the information included in this safety data sheet as a basis for conducting workplace-
specific risk assessments in order to establish the necessary risk prevention measures for the handling, use,
storage and disposal of this product.
Other legislation:
The REACH etc. (Amendment etc.) (EU Exit) Regulations 2020.
The Chemicals (Health and Safety) and Genetically Modified Organisms (Contained Use) (Amendment etc.) (EU
Exit) Regulations 2020.
Control of Substances Hazardous to Health Regulations 2002 (as amended)
EH40/2005 Workplace exposure limits.
SECTION 16: OTHER INFORMATION
Legislation related to safety data sheets:
This safety data sheet has been designed in accordance with ANNEX II-The REACH etc. (Amendment etc.) (EU
Exit) Regulations 2020.
Texts of the legislative phrases mentioned in section 3:
The phrases indicated do not refer to the product itself; they are present merely for informative purposes and
refer to the individual components which appear in section 3
GB CLP Regulation:
Non-applicable
Classification procedure:
Non-applicable
Advice related to training:
Training is recommended in order to prevent industrial risks for staff using this product and to facilitate their
comprehension and interpretation of this safety data sheet, as well as the label on the product.
Principal bibliographical sources:
http://echa.europa.eu
http://eur-lex.europa.eu
Abbreviations and acronyms:
ADR: European agreement concerning the international carriage of dangerous goods by road
IMDG: International maritime dangerous goods code
IATA: International Air Transport Association
ICAO: International Civil Aviation Organisation
COD: Chemical Oxygen Demand
BOD5: 5day biochemical oxygen demand
BCF: Bioconcentration factor
LD50: Lethal Dose 50
LC50: Lethal Concentration 50
EC50: Effective concentration 50
LogPOW: Octanolwater partition coefficient
Koc: Partition coefficient of organic carbon
UFI: unique formula identifier
IARC: International Agency for Research on Cancer
Theinformationcontainedinthissafetydatasheetisbasedonsources,technicalknowledgeandcurrentlegislationatUK,withoutbeingabletoguaranteeitsaccuracy.
Thisinformationcannotbeconsideredaguaranteeofthepropertiesoftheproduct,itissimplyadescriptionofthesecurityrequirements.Theoccupationalmethodology
andconditionsforusersofthisproductarenotwithinourawarenessorcontrol,anditisultimatelytheresponsibilityoftheusertotakethenecessarymeasurestoobtain
thelegalrequirementsconcerningthemanipulation,storage,useanddisposalofchemicalproducts.Theinformationonthissafetydatasheetonlyreferstothisproduct,
whichshouldnotbeusedforneedsotherthanthosespecified.
– END OF SAFETY DATA SHEET –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 8/8
by | Sep 27, 2025
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 1: IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKING
1.1Product identifier: BP850 – Polyurethane Tooling Board
Other means of identification:
Non-applicable
1.2Relevant identified uses of the substance or mixture and uses advised against:
Relevant uses: Non Hazardous Substance . For industrial user only.
Uses advised against: All uses not specified in this section or in section 7.3
1.3Details of the supplier of the safety data sheet:
Base Materials
Base Materials Ltd,20 Ashville Way
LE8 6NU Leicester – Whetstone – United Kingdom
Phone: 0116 286 5073
sales@base-materials.com
https://www.base-materials.com/
1.4Emergency telephone number: Ecostar Environmental – Reference Code: EREF-00111 : Telephone: +44 800
246 1972 (office hours), WhatsApp: +44 7496 228 905 (office hours), 24/7
Service +44 800 246 1274
SECTION 2: HAZARDS IDENTIFICATION
2.1Classification of the substance or mixture:
When milling: Dust will be produced
GB CLP Regulation:
The product is not classified as hazardous according to GB CLP Regulation.
2.2Label elements:
Metals in massive form, alloys, mixtures containing polymers and mixtures containing elastomers do not require
a label if they do not present a hazard to human health by inhalation, ingestion or contact with skin or to the
aquatic environment in the form in which they are placed on the market, although classified as hazardous.
GB CLP Regulation:
None
2.3Other hazards:
Product does not meet PBT/vPvB criteria
SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS
3.1Substance:
Non-applicable
3.2Mixture:
Chemical description: elastomeric matrix
Components:
None of the substances contained in the mixture are above the values fixed in Annex II of The REACH etc.
(Amendment etc.) (EU Exit) Regulations 2020.
Reaction product based on polyurethane
SECTION 4: FIRST AID MEASURES
4.1Description of first aid measures:
Consult a doctor in case of discomfort showing the SDS for the product.
By inhalation:
The possibility of being inhaled is practically nil, however, in the case of symptoms:
In case of symptoms, move the person affected into fresh air.
By skin contact:
– CONTINUED ON NEXT PAGE –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 1/8
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 4: FIRST AID MEASURES (continued)
In case of contact it is recommended to clean the affected area thoroughly with water and neutral soap. In case
of changes to the skin (stinging, redness, rashes, blisters, ), seek medical advice with this Safety Data Sheet
By eye contact:
Rinse with water until the product has been eliminated. In case of problems, consult a doctor showing the SDS
for the product.
By ingestion/aspiration:
In case of consumption in large quantities, it is recommended to seek medical assistance.
Dust: Provide fresh air.
4.2Most important symptoms and effects, both acute and delayed:
Acute and delayed effects are indicated in sections 2 and 11.
4.3Indication of any immediate medical attention and special treatment needed:
Non-applicable
SECTION 5: FIREFIGHTING MEASURES
5.1Extinguishing media:
Suitable extinguishing media:
Product is non-flammable, with a low risk of fire due to the flammability characteristics of the product in normal
conditions of storage, handling and use. In the case of the existence of sustained combustion as a result of
improper handling, storage or use any type of extinguishing agent can be used (ABC Powder, water,…)
Unsuitable extinguishing media:
Non-applicable
5.2Special hazards arising from the substance or mixture:
Due to its non-inflammable nature, the product does not present a fire risk under normal conditions of storage,
handling and use.
5.3Advice for firefighters:
Depending on the magnitude of the fire it may be necessary to use full protective clothing and self-contained
breathing apparatus (SCBA). Minimum emergency facilities and equipment should be available (fire blankets,
portable first aid kit,…).
Additional provisions:
Act in accordance with the Internal Emergency Plan and the Information Sheets on actions to take after an
accident or other emergencies. Eliminate all sources of ignition. In case of fire, cool the storage containers and
tanks for products susceptible to combustion, explosion or BLEVE as a result of high temperatures. Avoid spillage
of the products used to extinguish the fire into an aqueous medium.
SECTION 6: ACCIDENTAL RELEASE MEASURES
6.1Personal precautions, protective equipment and emergency procedures:
For non-emergency personnel:
Sweep up and shovel product or collect by other means and place in container for reuse (preferred) or disposal
For emergency responders:
Wear protective equipment. Keep unprotected persons away. See section 8.
Other information:
May form combustible dust concentrations in air. Keep away from sources of ignition – No smoking.
6.2Environmental precautions:
This product is not classified as hazardous to the environment. Keep product away from drains, surface and
ground water.
6.3Methods and material for containment and cleaning up:
It is recommended:
Sweep up and shovel product or collect by other means and place in container for reuse (preferred) or disposal
6.4Reference to other sections:
– CONTINUED ON NEXT PAGE –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 2/8
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 6: ACCIDENTAL RELEASE MEASURES (continued)
See sections 8 and 13.
SECTION 7: HANDLING AND STORAGE
7.1Precautions for safe handling:
A.-General precautions for safe use
Comply with the current legislation concerning the prevention of industrial risks with regards manually
handling weights. Maintain order, cleanliness and dispose of using safe methods (section 6).
B.-Technical recommendations for the prevention of fires and explosions
Due to its non-inflammable nature, the product does not present a fire risk under normal conditions of
storage, handling and use.
C.-Technical recommendations on general occupational hygiene
Do not eat or drink during the process, washing hands afterwards with suitable cleaning products.
D.-Technical recommendations to prevent environmental risks
It is not necessary to take special measures to prevent environmental risks. For more information see
subsection 6.2
Other information:
May form combustible dust concentrations in air. Keep away from sources of ignition – No smoking.
7.2Conditions for safe storage, including any incompatibilities:
A.-Technical measures for storage
Store in a cool, dry, well-ventilated location
B.-General conditions for storage
Avoid sources of heat, radiation, static electricity and contact with food. For additional information see
subsection 10.5
7.3Specific end use(s):
Except for the instructions already specified it is not necessary to provide any special recommendation regarding
the uses of this product.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1Control parameters:
Substances whose occupational exposure limits have to be monitored in the workplace:
Nuisance dust: Inhalable dust 10 mg/m3 // Respirable dust 4 mg/m3
DNEL (Workers):
Non-applicable
DNEL (General population):
Non-applicable
PNEC:
Non-applicable
8.2Exposure controls:
A.-Individual protection measures, such as personal protective equipment
As a preventative measure it is recommended to use basic Personal Protective Equipment, with the
corresponding <>. For more information on Personal Protective Equipment (storage, use,
cleaning, maintenance, class of protection, ) consult the information leaflet provided by the manufacturer. For
more information see subsection 7.1. All information contained herein is a recommendation which needs
some specification from the labour risk prevention services as it is not known whether the company has
additional measures at its disposal.
B.-Respiratory protection
The use of protection equipment will be necessary if a mist forms or if the occupational exposure limits are
exceeded.
C.-Specific protection for the hands
– CONTINUED ON NEXT PAGE –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 3/8
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION (continued)
Pictogram PPE Remarks
Mandatory hand
protection
Protective gloves against minor risks
Replace gloves in case of any sign of damage. For prolonged periods of
exposure to the product for professional users/industrials, we
recommend using CE III gloves in line with standards EN ISO
21420:2020 and EN ISO 374-1:2016+A1:2018
As the product is a mixture of several substances, the resistance of the glove material can not be calculated in
advance with total reliability and has therefore to be checked prior to the application.
D.-Eye and face protection
Pictogram PPE Remarks
Mandatory face
protection
Panoramic glasses against
splash/projections.
Clean daily and disinfect periodically according to the manufacturer s
instructions. Use if there is a risk of splashing.
E.-Body protection
Pictogram PPE Remarks
Work clothing
Replace before any evidence of deterioration. For periods of prolonged
exposure to the product for professional/industrial users CE III is
recommended, in accordance with the regulations in EN ISO 6529:2013,
EN ISO 6530:2005, EN ISO 13688:2013, EN 464:1994.
Anti-slip work shoes
Replace before any evidence of deterioration. For periods of prolonged
exposure to the product for professional/industrial users CE III is
recommended, in accordance with the regulations in EN ISO
20345:2012 y EN 13832-1:2007
F.-Additional emergency measures
It is not necessary to take additional emergency measures.
Environmental exposure controls:
In accordance with the community legislation for the protection of the environment it is recommended to avoid
environmental spillage of both the product and its container. For additional information see subsection 7.1.D
The Volatile Organic Compounds in Paints, Varnishes and Vehicle Refinishing Products Regulations
2012:
V.O.C. (Supply): 0 % weight
V.O.C. density at 20 C: 0 kg/m (0 g/L)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
9.1Information on basic physical and chemical properties:
For complete information see the product datasheet.
Appearance:
Physical state at 20 C: Solid
Appearance: Not available
Colour: Grey
Odour: Not available
Odour threshold: Non-applicable *
Volatility:
Boiling point at atmospheric pressure: Non-applicable *
Vapour pressure at 20 C: Non-applicable *
Vapour pressure at 50 C: Non-applicable *
Evaporation rate at 20 C: Non-applicable *
*Not relevant due to the nature of the product, not providing information property of its hazards.
– CONTINUED ON NEXT PAGE –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 4/8
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES (continued)
Product description:
Density at 20 C: ca. 850 kg/m
Relative density at 20 C: ca. 0.85
Dynamic viscosity at 20 C: Non-applicable *
Kinematic viscosity at 20 C: Non-applicable *
Kinematic viscosity at 40 C: Non-applicable *
Concentration: Non-applicable *
pH: Non-applicable *
Vapour density at 20 C: Non-applicable *
Partition coefficient n-octanol/water 20 C: Non-applicable *
Solubility in water at 20 C: Non-applicable *
Solubility properties: Non-applicable *
Decomposition temperature: Non-applicable *
Melting point/freezing point: Non-applicable *
Flammability:
Flash Point: Non-applicable
Flammability (solid, gas): Non-applicable *
Autoignition temperature: Non-applicable *
Lower flammability limit: Non-applicable *
Upper flammability limit: Non-applicable *
Explosive (Solid):
Lower explosive limit: Non-applicable *
Upper explosive limit: Non-applicable *
Particle characteristics:
Median equivalent diameter: Non-applicable *
9.2Other information:
Information with regard to physical hazard classes:
Explosive properties: Non-applicable *
Oxidising properties: Non-applicable *
Corrosive to metals: Non-applicable *
Heat of combustion: Non-applicable *
Aerosols-total percentage (by mass) of
flammable components:
Non-applicable *
Other safety characteristics:
Surface tension at 20 C: Non-applicable *
Refraction index: Non-applicable *
*Not relevant due to the nature of the product, not providing information property of its hazards.
SECTION 10: STABILITY AND REACTIVITY
10.1Reactivity:
No hazardous reactions are expected because the product is stable under recommended storage conditions. See
section 7 from Safety Data Sheet.
10.2Chemical stability:
Chemically stable under the indicated conditions of storage, handling and use.
10.3Possibility of hazardous reactions:
Under the specified conditions, hazardous reactions that lead to excessive temperatures or pressure are not
expected.
– CONTINUED ON NEXT PAGE –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 5/8
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 10: STABILITY AND REACTIVITY (continued)
10.4Conditions to avoid:
Applicable for handling and storage at room temperature:
Shock and friction Contact with air Increase in temperature Sunlight Humidity
Not applicable Not applicable Not applicable Not applicable Not applicable
10.5Incompatible materials:
Acids Water Oxidising materials Combustible materials Others
Avoid strong acids Not applicable Not applicable Not applicable
Avoid alkalis or strong
bases
10.6Hazardous decomposition products:
See subsection 10.3, 10.4 and 10.5 to find out the specific decomposition products. Depending on the
decomposition conditions, complex mixtures of chemical substances can be released: carbon dioxide (CO ),
carbon monoxide and other organic compounds.
SECTION 11: TOXICOLOGICAL INFORMATION
11.1Information on toxicological effects:
LD50 oral > 2000 mg/kg (rat)
Dangerous health implications:
In case of exposure that is repetitive, prolonged or at concentrations higher than the recommended occupational
exposure limits, adverse effects on health may result, depending on the means of exposure:
A-Ingestion (acute effect):
– Acute toxicity: Based on available data, the classification criteria are not met
– Corrosivity/Irritability: Based on available data, the classification criteria are not met
B-Inhalation (acute effect):
It is advised that, due to the encapsulation of the active ingredient, it is estimated that inhalation hazards
could be minimized. This criterion applies throughout the entire SDS.
– Acute toxicity : Based on available data, the classification criteria are not met
– Corrosivity/Irritability: Based on available data, the classification criteria are not met
C-Contact with the skin and the eyes (acute effect):
– Contact with the skin: Based on available data, the classification criteria are not met
– Contact with the eyes: Based on available data, the classification criteria are not met
D-CMR effects (carcinogenicity, mutagenicity and toxicity to reproduction):
– Carcinogenicity: Based on available data, the classification criteria are not met
IARC: Non-applicable
– Mutagenicity: Based on available data, the classification criteria are not met
– Reproductive toxicity: Based on available data, the classification criteria are not met
E-Sensitizing effects:
– Respiratory: Based on available data, the classification criteria are not met
– Skin: Based on available data, the classification criteria are not met
F-Specific target organ toxicity (STOT) – single exposure:
Based on available data, the classification criteria are not met
G-Specific target organ toxicity (STOT)-repeated exposure:
– Specific target organ toxicity (STOT)-repeated exposure: Based on available data, the classification criteria
are not met
– Skin: Based on available data, the classification criteria are not met, as it does not contain substances
classified as hazardous for this effect. For more information see section 3.
H-Aspiration hazard:
Based on available data, the classification criteria are not met
Other information:
Non-applicable
– CONTINUED ON NEXT PAGE –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 6/8
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 11: TOXICOLOGICAL INFORMATION (continued)
Specific toxicology information on the substances:
Not available
SECTION 12: ECOLOGICAL INFORMATION
The experimental information related to the eco-toxicological properties of the product itself is not available
Based on available data, the classification criteria are not met
12.1Toxicity:
Not available
12.2Persistence and degradability:
Not available
12.3Bioaccumulative potential:
Not available
12.4Mobility in soil:
Not available
12.5Results of PBT and vPvB assessment:
Product does not meet PBT/vPvB criteria
12.6Other adverse effects:
Not described
SECTION 13: DISPOSAL CONSIDERATIONS
13.1Waste treatment methods:
Code Description Waste class
16 03 06 organic wastes other than those mentioned in 16 03 05 Non dangerous
Type of waste:
Non-applicable
Waste management (disposal and evaluation):
Consult the authorized waste service manager on the assessment and disposal operations in accordance The
Waste Regulations 2011, 2011 No. 988. As under 15 01 of the code and in case the container has been in direct
contact with the product, it will be processed the same way as the actual product. Otherwise, it will be processed
as non-dangerous residue. Waste should not be disposed of to drains. See paragraph 6.2.
Regulations related to waste management:
In accordance with Annex II of UK REACH the provisions related to waste management are stated:
UK legislation: The Waste Regulations 2011.
SECTION 14: TRANSPORT INFORMATION
This product is not regulated for transport (ADR/RID,IMDG,IATA)
SECTION 15: REGULATORY INFORMATION
15.1Safety, health and environmental regulations/legislation specific for the substance or mixture:
– Substances listed in UK candidate list of substances of very high concern (SVHCs): Non-applicable
– Substances listed in UK REACH Authorisation List (Annex 14): Non-applicable
The Control of Major Accident Hazards Regulations 2015:
Non-applicable
– CONTINUED ON NEXT PAGE –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 7/8
BP850 – Polyurethane Tooling Board
Safety data sheet
According to UK REACH
SECTION 15: REGULATORY INFORMATION (continued)
Restrictions to commercialisation and the use of certain dangerous substances and mixtures (Annex
XVII UK REACH, etc .):
Non-applicable
Specific provisions in terms of protecting people or the environment:
It is recommended to use the information included in this safety data sheet as a basis for conducting workplace-
specific risk assessments in order to establish the necessary risk prevention measures for the handling, use,
storage and disposal of this product.
Other legislation:
The REACH etc. (Amendment etc.) (EU Exit) Regulations 2020.
The Chemicals (Health and Safety) and Genetically Modified Organisms (Contained Use) (Amendment etc.) (EU
Exit) Regulations 2020.
Control of Substances Hazardous to Health Regulations 2002 (as amended)
EH40/2005 Workplace exposure limits.
SECTION 16: OTHER INFORMATION
Legislation related to safety data sheets:
This safety data sheet has been designed in accordance with ANNEX II-The REACH etc. (Amendment etc.) (EU
Exit) Regulations 2020.
Texts of the legislative phrases mentioned in section 3:
The phrases indicated do not refer to the product itself; they are present merely for informative purposes and
refer to the individual components which appear in section 3
GB CLP Regulation:
Non-applicable
Classification procedure:
Non-applicable
Advice related to training:
Training is recommended in order to prevent industrial risks for staff using this product and to facilitate their
comprehension and interpretation of this safety data sheet, as well as the label on the product.
Principal bibliographical sources:
http://echa.europa.eu
http://eur-lex.europa.eu
Abbreviations and acronyms:
ADR: European agreement concerning the international carriage of dangerous goods by road
IMDG: International maritime dangerous goods code
IATA: International Air Transport Association
ICAO: International Civil Aviation Organisation
COD: Chemical Oxygen Demand
BOD5: 5day biochemical oxygen demand
BCF: Bioconcentration factor
LD50: Lethal Dose 50
LC50: Lethal Concentration 50
EC50: Effective concentration 50
LogPOW: Octanolwater partition coefficient
Koc: Partition coefficient of organic carbon
UFI: unique formula identifier
IARC: International Agency for Research on Cancer
Theinformationcontainedinthissafetydatasheetisbasedonsources,technicalknowledgeandcurrentlegislationatUK,withoutbeingabletoguaranteeitsaccuracy.
Thisinformationcannotbeconsideredaguaranteeofthepropertiesoftheproduct,itissimplyadescriptionofthesecurityrequirements.Theoccupationalmethodology
andconditionsforusersofthisproductarenotwithinourawarenessorcontrol,anditisultimatelytheresponsibilityoftheusertotakethenecessarymeasurestoobtain
thelegalrequirementsconcerningthemanipulation,storage,useanddisposalofchemicalproducts.Theinformationonthissafetydatasheetonlyreferstothisproduct,
whichshouldnotbeusedforneedsotherthanthosespecified.
– END OF SAFETY DATA SHEET –
Date of compilation: 04/08/2022 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 8/8
by | Sep 27, 2025
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 1: IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKING
1.1Product identifier: BE978 – Epoxy Tooling Board
Not a hazardous substance
CAS: Non-applicable
Other means of identification:
Non-applicable
1.2Relevant identified uses of the substance or mixture and uses advised against:
Relevant uses: Non Hazardous Substance . For industrial user only.
Uses advised against: All uses not specified in this section or in section 7.3
1.3Details of the supplier of the safety data sheet:
Base Materials
Base Materials Ltd,20 Ashville Way
LE8 6NU Leicester – Whetstone – United Kingdom
Phone: 0116 286 5073
sales@base-materials.com
https://www.base-materials.com/
1.4Emergency telephone number: Ecostar Environmental – Reference Code: EREF-00111 : Telephone: +44 800
246 1972 (office hours), WhatsApp: +44 7496 228 905 (office hours), 24/7
Service +44 800 246 1274
SECTION 2: HAZARDS IDENTIFICATION
2.1Classification of the substance or mixture:
When milling: Dust will be produced
GB CLP Regulation:
The product is not classified as hazardous according to GB CLP Regulation.
2.2Label elements:
GB CLP Regulation:
None
2.3Other hazards:
Product does not meet PBT/vPvB criteria
SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS
3.1Substance:
Chemical description: Epoxides
Components:
In accordance with Annex II of The REACH etc. (Amendment etc.) (EU Exit) Regulations 2020, the product
contains:
Identification Chemical name/Classification
Concentratio
n
CAS:Non-applicable
Not a hazardous substance
100 %
To obtain more information on the hazards of the substances consult sections 11, 12 and 16.
3.2Mixture:
Non-applicable
Reaction product based on epoxy
SECTION 4: FIRST AID MEASURES
4.1Description of first aid measures:
Consult a doctor in case of discomfort showing the SDS for the product.
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 1/8
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 4: FIRST AID MEASURES (continued)
By inhalation:
In case of symptoms, move the person affected into fresh air.
By skin contact:
In case of contact it is recommended to clean the affected area thoroughly with water and neutral soap. In case
of changes to the skin (stinging, redness, rashes, blisters, ), seek medical advice with this Safety Data Sheet
By eye contact:
Rinse with water until the product has been eliminated. In case of problems, consult a doctor showing the SDS
for the product.
By ingestion/aspiration:
In case of consumption in large quantities, it is recommended to seek medical assistance.
Dust: Provide fresh air.
4.2Most important symptoms and effects, both acute and delayed:
Acute and delayed effects are indicated in sections 2 and 11.
4.3Indication of any immediate medical attention and special treatment needed:
Non-applicable
SECTION 5: FIREFIGHTING MEASURES
5.1Extinguishing media:
Suitable extinguishing media:
Product is non-flammable, with a low risk of fire due to the flammability characteristics of the product in normal
conditions of storage, handling and use. In the case of the existence of sustained combustion as a result of
improper handling, storage or use any type of extinguishing agent can be used (ABC Powder, water,…)
Unsuitable extinguishing media:
Non-applicable
5.2Special hazards arising from the substance or mixture:
Due to its non-inflammable nature, the product does not present a fire risk under normal conditions of storage,
handling and use.
5.3Advice for firefighters:
Depending on the magnitude of the fire it may be necessary to use full protective clothing and self-contained
breathing apparatus (SCBA). Minimum emergency facilities and equipment should be available (fire blankets,
portable first aid kit,…).
Additional provisions:
Act in accordance with the Internal Emergency Plan and the Information Sheets on actions to take after an
accident or other emergencies. Eliminate all sources of ignition. In case of fire, cool the storage containers and
tanks for products susceptible to combustion, explosion or BLEVE as a result of high temperatures. Avoid spillage
of the products used to extinguish the fire into an aqueous medium.
SECTION 6: ACCIDENTAL RELEASE MEASURES
6.1Personal precautions, protective equipment and emergency procedures:
For non-emergency personnel:
Sweep up and shovel product or collect by other means and place in container for reuse (preferred) or disposal
For emergency responders:
Wear protective equipment. Keep unprotected persons away. See section 8.
Other information:
May form combustible dust concentrations in air. Keep away from sources of ignition – No smoking.
6.2Environmental precautions:
This product is not classified as hazardous to the environment. Keep product away from drains, surface and
ground water.
6.3Methods and material for containment and cleaning up:
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 2/8
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 6: ACCIDENTAL RELEASE MEASURES (continued)
It is recommended:
Sweep up and shovel product or collect by other means and place in container for reuse (preferred) or disposal
6.4Reference to other sections:
See sections 8 and 13.
SECTION 7: HANDLING AND STORAGE
7.1Precautions for safe handling:
A.-General precautions for safe use
Comply with the current legislation concerning the prevention of industrial risks with regards manually
handling weights. Maintain order, cleanliness and dispose of using safe methods (section 6).
B.-Technical recommendations for the prevention of fires and explosions
Due to its non-inflammable nature, the product does not present a fire risk under normal conditions of
storage, handling and use.
C.-Technical recommendations on general occupational hygiene
Do not eat or drink during the process, washing hands afterwards with suitable cleaning products.
D.-Technical recommendations to prevent environmental risks
It is not necessary to take special measures to prevent environmental risks. For more information see
subsection 6.2
Other information:
May form combustible dust concentrations in air. Keep away from sources of ignition – No smoking.
7.2Conditions for safe storage, including any incompatibilities:
A.-Technical measures for storage
Store in a cool, dry, well-ventilated location
B.-General conditions for storage
Avoid sources of heat, radiation, static electricity and contact with food. For additional information see
subsection 10.5
7.3Specific end use(s):
Except for the instructions already specified it is not necessary to provide any special recommendation regarding
the uses of this product.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1Control parameters:
Substances whose occupational exposure limits have to be monitored in the workplace:
Nuisance dust: Inhalable dust 10 mg/m3 // Respirable dust 4 mg/m3
DNEL (Workers):
Non-applicable
DNEL (General population):
Non-applicable
PNEC:
Non-applicable
8.2Exposure controls:
A.-Individual protection measures, such as personal protective equipment
As a preventative measure it is recommended to use basic Personal Protective Equipment, with the
corresponding <>. For more information on Personal Protective Equipment (storage, use,
cleaning, maintenance, class of protection, ) consult the information leaflet provided by the manufacturer. For
more information see subsection 7.1. All information contained herein is a recommendation which needs
some specification from the labour risk prevention services as it is not known whether the company has
additional measures at its disposal.
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 3/8
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION (continued)
B.-Respiratory protection
The use of protection equipment will be necessary if a mist forms or if the occupational exposure limits are
exceeded.
C.-Specific protection for the hands
Pictogram PPE Remarks
Mandatory hand
protection
Protective gloves against minor risks
Replace gloves in case of any sign of damage. For prolonged periods of
exposure to the product for professional users/industrials, we
recommend using CE III gloves in line with standards EN ISO
21420:2020 and EN ISO 374-1:2016+A1:2018
D.-Eye and face protection
Pictogram PPE Remarks
Mandatory face
protection
Panoramic glasses against
splash/projections.
Clean daily and disinfect periodically according to the manufacturer s
instructions. Use if there is a risk of splashing.
E.-Body protection
Pictogram PPE Remarks
Work clothing
Replace before any evidence of deterioration. For periods of prolonged
exposure to the product for professional/industrial users CE III is
recommended, in accordance with the regulations in EN ISO 6529:2013,
EN ISO 6530:2005, EN ISO 13688:2013, EN 464:1994.
Anti-slip work shoes
Replace before any evidence of deterioration. For periods of prolonged
exposure to the product for professional/industrial users CE III is
recommended, in accordance with the regulations in EN ISO
20345:2012 y EN 13832-1:2007
F.-Additional emergency measures
It is not necessary to take additional emergency measures.
Environmental exposure controls:
In accordance with the community legislation for the protection of the environment it is recommended to avoid
environmental spillage of both the product and its container. For additional information see subsection 7.1.D
The Volatile Organic Compounds in Paints, Varnishes and Vehicle Refinishing Products Regulations
2012:
V.O.C. (Supply): 0 % weight
V.O.C. density at 20 C: 0 kg/m (0 g/L)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
9.1Information on basic physical and chemical properties:
For complete information see the product datasheet.
Appearance:
Physical state at 20 C: Solid
Appearance: Not available
Colour: Aqua
Odour: Not available
Odour threshold: Non-applicable *
Volatility:
Boiling point at atmospheric pressure: Non-applicable *
Vapour pressure at 20 C: Non-applicable *
*Not relevant due to the nature of the product, not providing information property of its hazards.
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 4/8
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES (continued)
Vapour pressure at 50 C: Non-applicable *
Evaporation rate at 20 C: Non-applicable *
Product description:
Density at 20 C: ca. 700 kg/m
Relative density at 20 C: ca. 0.7
Dynamic viscosity at 20 C: Non-applicable *
Kinematic viscosity at 20 C: Non-applicable *
Kinematic viscosity at 40 C: Non-applicable *
Concentration: Non-applicable *
pH: Non-applicable *
Vapour density at 20 C: Non-applicable *
Partition coefficient n-octanol/water 20 C: Non-applicable *
Solubility in water at 20 C: Non-applicable *
Solubility properties: Non-applicable *
Decomposition temperature: Non-applicable *
Melting point/freezing point: Non-applicable *
Flammability:
Flash Point: Non-applicable
Flammability (solid, gas): Non-applicable *
Autoignition temperature: Non-applicable *
Lower flammability limit: Non-applicable *
Upper flammability limit: Non-applicable *
Explosive (Solid):
Lower explosive limit: Non-applicable *
Upper explosive limit: Non-applicable *
Particle characteristics:
Median equivalent diameter: Non-applicable *
9.2Other information:
Information with regard to physical hazard classes:
Explosive properties: Non-applicable *
Oxidising properties: Non-applicable *
Corrosive to metals: Non-applicable *
Heat of combustion: Non-applicable *
Aerosols-total percentage (by mass) of
flammable components:
Non-applicable *
Other safety characteristics:
Surface tension at 20 C: Non-applicable *
Refraction index: Non-applicable *
*Not relevant due to the nature of the product, not providing information property of its hazards.
SECTION 10: STABILITY AND REACTIVITY
10.1Reactivity:
No hazardous reactions are expected because the product is stable under recommended storage conditions. See
section 7 from Safety Data Sheet.
10.2Chemical stability:
Chemically stable under the indicated conditions of storage, handling and use.
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 5/8
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 10: STABILITY AND REACTIVITY (continued)
10.3Possibility of hazardous reactions:
Under the specified conditions, hazardous reactions that lead to excessive temperatures or pressure are not
expected.
10.4Conditions to avoid:
Applicable for handling and storage at room temperature:
Shock and friction Contact with air Increase in temperature Sunlight Humidity
Not applicable Not applicable Not applicable Not applicable Not applicable
10.5Incompatible materials:
Acids Water Oxidising materials Combustible materials Others
Avoid strong acids Not applicable Not applicable Not applicable
Avoid alkalis or strong
bases
10.6Hazardous decomposition products:
See subsection 10.3, 10.4 and 10.5 to find out the specific decomposition products. Depending on the
decomposition conditions, complex mixtures of chemical substances can be released: carbon dioxide (CO ),
carbon monoxide and other organic compounds.
SECTION 11: TOXICOLOGICAL INFORMATION
11.1Information on toxicological effects:
LD50 oral > 2000 mg/kg (rat)
Dangerous health implications:
In case of exposure that is repetitive, prolonged or at concentrations higher than the recommended occupational
exposure limits, adverse effects on health may result, depending on the means of exposure:
A-Ingestion (acute effect):
– Acute toxicity: Based on available data, the classification criteria are not met
– Corrosivity/Irritability: Based on available data, the classification criteria are not met
B-Inhalation (acute effect):
– Acute toxicity : Based on available data, the classification criteria are not met
– Corrosivity/Irritability: Based on available data, the classification criteria are not met
C-Contact with the skin and the eyes (acute effect):
– Contact with the skin: Based on available data, the classification criteria are not met
– Contact with the eyes: Based on available data, the classification criteria are not met
D-CMR effects (carcinogenicity, mutagenicity and toxicity to reproduction):
– Carcinogenicity: Based on available data, the classification criteria are not met
IARC: Non-applicable
– Mutagenicity: Based on available data, the classification criteria are not met
– Reproductive toxicity: Based on available data, the classification criteria are not met
E-Sensitizing effects:
– Respiratory: Based on available data, the classification criteria are not met
– Skin: Based on available data, the classification criteria are not met
F-Specific target organ toxicity (STOT) – single exposure:
Based on available data, the classification criteria are not met
G-Specific target organ toxicity (STOT)-repeated exposure:
– Specific target organ toxicity (STOT)-repeated exposure: Based on available data, the classification criteria
are not met
– Skin: Based on available data, the classification criteria are not met, as it does not contain substances
classified as hazardous for this effect. For more information see section 3.
H-Aspiration hazard:
Based on available data, the classification criteria are not met
Other information:
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 6/8
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 11: TOXICOLOGICAL INFORMATION (continued)
Non-applicable
Specific toxicology information on the substances:
Not available
SECTION 12: ECOLOGICAL INFORMATION
The experimental information related to the eco-toxicological properties of the product itself is not available
Based on available data, the classification criteria are not met
12.1Toxicity:
Not available
12.2Persistence and degradability:
Not available
12.3Bioaccumulative potential:
Not available
12.4Mobility in soil:
Not available
12.5Results of PBT and vPvB assessment:
Product does not meet PBT/vPvB criteria
12.6Other adverse effects:
Not described
SECTION 13: DISPOSAL CONSIDERATIONS
13.1Waste treatment methods:
Code Description Waste class
It is not possible to assign a specific code, as it depends on the intended use by the
user
Non dangerous
Type of waste:
Non-applicable
Waste management (disposal and evaluation):
Consult the authorized waste service manager on the assessment and disposal operations in accordance The
Waste Regulations 2011, 2011 No. 988. As under 15 01 of the code and in case the container has been in direct
contact with the product, it will be processed the same way as the actual product. Otherwise, it will be processed
as non-dangerous residue. Waste should not be disposed of to drains. See paragraph 6.2.
Regulations related to waste management:
In accordance with Annex II of UK REACH the provisions related to waste management are stated:
UK legislation: The Waste Regulations 2011.
SECTION 14: TRANSPORT INFORMATION
This product is not regulated for transport (ADR/RID,IMDG,IATA)
SECTION 15: REGULATORY INFORMATION
15.1Safety, health and environmental regulations/legislation specific for the substance or mixture:
– Substances listed in UK candidate list of substances of very high concern (SVHCs): Non-applicable
– Substances listed in UK REACH Authorisation List (Annex 14): Non-applicable
The Control of Major Accident Hazards Regulations 2015:
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 7/8
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 15: REGULATORY INFORMATION (continued)
Non-applicable
Restrictions to commercialisation and the use of certain dangerous substances and mixtures (Annex
XVII UK REACH, etc .):
Non-applicable
Specific provisions in terms of protecting people or the environment:
It is recommended to use the information included in this safety data sheet as a basis for conducting workplace-
specific risk assessments in order to establish the necessary risk prevention measures for the handling, use,
storage and disposal of this product.
Other legislation:
The REACH etc. (Amendment etc.) (EU Exit) Regulations 2020.
The Chemicals (Health and Safety) and Genetically Modified Organisms (Contained Use) (Amendment etc.) (EU
Exit) Regulations 2020.
Control of Substances Hazardous to Health Regulations 2002 (as amended)
EH40/2005 Workplace exposure limits.
SECTION 16: OTHER INFORMATION
Legislation related to safety data sheets:
This safety data sheet has been designed in accordance with ANNEX II-The REACH etc. (Amendment etc.) (EU
Exit) Regulations 2020.
Texts of the legislative phrases mentioned in section 3:
The phrases indicated do not refer to the product itself; they are present merely for informative purposes and
refer to the individual components which appear in section 3
GB CLP Regulation:
Non-applicable
Advice related to training:
Training is recommended in order to prevent industrial risks for staff using this product and to facilitate their
comprehension and interpretation of this safety data sheet, as well as the label on the product.
Principal bibliographical sources:
http://echa.europa.eu
http://eur-lex.europa.eu
Abbreviations and acronyms:
ADR: European agreement concerning the international carriage of dangerous goods by road
IMDG: International maritime dangerous goods code
IATA: International Air Transport Association
ICAO: International Civil Aviation Organisation
COD: Chemical Oxygen Demand
BOD5: 5day biochemical oxygen demand
BCF: Bioconcentration factor
LD50: Lethal Dose 50
LC50: Lethal Concentration 50
EC50: Effective concentration 50
LogPOW: Octanolwater partition coefficient
Koc: Partition coefficient of organic carbon
UFI: unique formula identifier
IARC: International Agency for Research on Cancer
Theinformationcontainedinthissafetydatasheetisbasedonsources,technicalknowledgeandcurrentlegislationatUK,withoutbeingabletoguaranteeitsaccuracy.
Thisinformationcannotbeconsideredaguaranteeofthepropertiesoftheproduct,itissimplyadescriptionofthesecurityrequirements.Theoccupationalmethodology
andconditionsforusersofthisproductarenotwithinourawarenessorcontrol,anditisultimatelytheresponsibilityoftheusertotakethenecessarymeasurestoobtain
thelegalrequirementsconcerningthemanipulation,storage,useanddisposalofchemicalproducts.Theinformationonthissafetydatasheetonlyreferstothisproduct,
whichshouldnotbeusedforneedsotherthanthosespecified.
– END OF SAFETY DATA SHEET –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 8/8
by | Sep 27, 2025
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 1: IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKING
1.1Product identifier: BE978 – Epoxy Tooling Board
Not a hazardous substance
CAS: Non-applicable
Other means of identification:
Non-applicable
1.2Relevant identified uses of the substance or mixture and uses advised against:
Relevant uses: Non Hazardous Substance . For industrial user only.
Uses advised against: All uses not specified in this section or in section 7.3
1.3Details of the supplier of the safety data sheet:
Base Materials
Base Materials Ltd,20 Ashville Way
LE8 6NU Leicester – Whetstone – United Kingdom
Phone: 0116 286 5073
sales@base-materials.com
https://www.base-materials.com/
1.4Emergency telephone number: Ecostar Environmental – Reference Code: EREF-00111 : Telephone: +44 800
246 1972 (office hours), WhatsApp: +44 7496 228 905 (office hours), 24/7
Service +44 800 246 1274
SECTION 2: HAZARDS IDENTIFICATION
2.1Classification of the substance or mixture:
When milling: Dust will be produced
GB CLP Regulation:
The product is not classified as hazardous according to GB CLP Regulation.
2.2Label elements:
GB CLP Regulation:
None
2.3Other hazards:
Product does not meet PBT/vPvB criteria
SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS
3.1Substance:
Chemical description: Epoxides
Components:
In accordance with Annex II of The REACH etc. (Amendment etc.) (EU Exit) Regulations 2020, the product
contains:
Identification Chemical name/Classification
Concentratio
n
CAS:Non-applicable
Not a hazardous substance
100 %
To obtain more information on the hazards of the substances consult sections 11, 12 and 16.
3.2Mixture:
Non-applicable
Reaction product based on epoxy
SECTION 4: FIRST AID MEASURES
4.1Description of first aid measures:
Consult a doctor in case of discomfort showing the SDS for the product.
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 1/8
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 4: FIRST AID MEASURES (continued)
By inhalation:
In case of symptoms, move the person affected into fresh air.
By skin contact:
In case of contact it is recommended to clean the affected area thoroughly with water and neutral soap. In case
of changes to the skin (stinging, redness, rashes, blisters, ), seek medical advice with this Safety Data Sheet
By eye contact:
Rinse with water until the product has been eliminated. In case of problems, consult a doctor showing the SDS
for the product.
By ingestion/aspiration:
In case of consumption in large quantities, it is recommended to seek medical assistance.
Dust: Provide fresh air.
4.2Most important symptoms and effects, both acute and delayed:
Acute and delayed effects are indicated in sections 2 and 11.
4.3Indication of any immediate medical attention and special treatment needed:
Non-applicable
SECTION 5: FIREFIGHTING MEASURES
5.1Extinguishing media:
Suitable extinguishing media:
Product is non-flammable, with a low risk of fire due to the flammability characteristics of the product in normal
conditions of storage, handling and use. In the case of the existence of sustained combustion as a result of
improper handling, storage or use any type of extinguishing agent can be used (ABC Powder, water,…)
Unsuitable extinguishing media:
Non-applicable
5.2Special hazards arising from the substance or mixture:
Due to its non-inflammable nature, the product does not present a fire risk under normal conditions of storage,
handling and use.
5.3Advice for firefighters:
Depending on the magnitude of the fire it may be necessary to use full protective clothing and self-contained
breathing apparatus (SCBA). Minimum emergency facilities and equipment should be available (fire blankets,
portable first aid kit,…).
Additional provisions:
Act in accordance with the Internal Emergency Plan and the Information Sheets on actions to take after an
accident or other emergencies. Eliminate all sources of ignition. In case of fire, cool the storage containers and
tanks for products susceptible to combustion, explosion or BLEVE as a result of high temperatures. Avoid spillage
of the products used to extinguish the fire into an aqueous medium.
SECTION 6: ACCIDENTAL RELEASE MEASURES
6.1Personal precautions, protective equipment and emergency procedures:
For non-emergency personnel:
Sweep up and shovel product or collect by other means and place in container for reuse (preferred) or disposal
For emergency responders:
Wear protective equipment. Keep unprotected persons away. See section 8.
Other information:
May form combustible dust concentrations in air. Keep away from sources of ignition – No smoking.
6.2Environmental precautions:
This product is not classified as hazardous to the environment. Keep product away from drains, surface and
ground water.
6.3Methods and material for containment and cleaning up:
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 2/8
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 6: ACCIDENTAL RELEASE MEASURES (continued)
It is recommended:
Sweep up and shovel product or collect by other means and place in container for reuse (preferred) or disposal
6.4Reference to other sections:
See sections 8 and 13.
SECTION 7: HANDLING AND STORAGE
7.1Precautions for safe handling:
A.-General precautions for safe use
Comply with the current legislation concerning the prevention of industrial risks with regards manually
handling weights. Maintain order, cleanliness and dispose of using safe methods (section 6).
B.-Technical recommendations for the prevention of fires and explosions
Due to its non-inflammable nature, the product does not present a fire risk under normal conditions of
storage, handling and use.
C.-Technical recommendations on general occupational hygiene
Do not eat or drink during the process, washing hands afterwards with suitable cleaning products.
D.-Technical recommendations to prevent environmental risks
It is not necessary to take special measures to prevent environmental risks. For more information see
subsection 6.2
Other information:
May form combustible dust concentrations in air. Keep away from sources of ignition – No smoking.
7.2Conditions for safe storage, including any incompatibilities:
A.-Technical measures for storage
Store in a cool, dry, well-ventilated location
B.-General conditions for storage
Avoid sources of heat, radiation, static electricity and contact with food. For additional information see
subsection 10.5
7.3Specific end use(s):
Except for the instructions already specified it is not necessary to provide any special recommendation regarding
the uses of this product.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1Control parameters:
Substances whose occupational exposure limits have to be monitored in the workplace:
Nuisance dust: Inhalable dust 10 mg/m3 // Respirable dust 4 mg/m3
DNEL (Workers):
Non-applicable
DNEL (General population):
Non-applicable
PNEC:
Non-applicable
8.2Exposure controls:
A.-Individual protection measures, such as personal protective equipment
As a preventative measure it is recommended to use basic Personal Protective Equipment, with the
corresponding <>. For more information on Personal Protective Equipment (storage, use,
cleaning, maintenance, class of protection, ) consult the information leaflet provided by the manufacturer. For
more information see subsection 7.1. All information contained herein is a recommendation which needs
some specification from the labour risk prevention services as it is not known whether the company has
additional measures at its disposal.
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 3/8
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION (continued)
B.-Respiratory protection
The use of protection equipment will be necessary if a mist forms or if the occupational exposure limits are
exceeded.
C.-Specific protection for the hands
Pictogram PPE Remarks
Mandatory hand
protection
Protective gloves against minor risks
Replace gloves in case of any sign of damage. For prolonged periods of
exposure to the product for professional users/industrials, we
recommend using CE III gloves in line with standards EN ISO
21420:2020 and EN ISO 374-1:2016+A1:2018
D.-Eye and face protection
Pictogram PPE Remarks
Mandatory face
protection
Panoramic glasses against
splash/projections.
Clean daily and disinfect periodically according to the manufacturer s
instructions. Use if there is a risk of splashing.
E.-Body protection
Pictogram PPE Remarks
Work clothing
Replace before any evidence of deterioration. For periods of prolonged
exposure to the product for professional/industrial users CE III is
recommended, in accordance with the regulations in EN ISO 6529:2013,
EN ISO 6530:2005, EN ISO 13688:2013, EN 464:1994.
Anti-slip work shoes
Replace before any evidence of deterioration. For periods of prolonged
exposure to the product for professional/industrial users CE III is
recommended, in accordance with the regulations in EN ISO
20345:2012 y EN 13832-1:2007
F.-Additional emergency measures
It is not necessary to take additional emergency measures.
Environmental exposure controls:
In accordance with the community legislation for the protection of the environment it is recommended to avoid
environmental spillage of both the product and its container. For additional information see subsection 7.1.D
The Volatile Organic Compounds in Paints, Varnishes and Vehicle Refinishing Products Regulations
2012:
V.O.C. (Supply): 0 % weight
V.O.C. density at 20 C: 0 kg/m (0 g/L)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
9.1Information on basic physical and chemical properties:
For complete information see the product datasheet.
Appearance:
Physical state at 20 C: Solid
Appearance: Not available
Colour: Aqua
Odour: Not available
Odour threshold: Non-applicable *
Volatility:
Boiling point at atmospheric pressure: Non-applicable *
Vapour pressure at 20 C: Non-applicable *
*Not relevant due to the nature of the product, not providing information property of its hazards.
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 4/8
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES (continued)
Vapour pressure at 50 C: Non-applicable *
Evaporation rate at 20 C: Non-applicable *
Product description:
Density at 20 C: ca. 700 kg/m
Relative density at 20 C: ca. 0.7
Dynamic viscosity at 20 C: Non-applicable *
Kinematic viscosity at 20 C: Non-applicable *
Kinematic viscosity at 40 C: Non-applicable *
Concentration: Non-applicable *
pH: Non-applicable *
Vapour density at 20 C: Non-applicable *
Partition coefficient n-octanol/water 20 C: Non-applicable *
Solubility in water at 20 C: Non-applicable *
Solubility properties: Non-applicable *
Decomposition temperature: Non-applicable *
Melting point/freezing point: Non-applicable *
Flammability:
Flash Point: Non-applicable
Flammability (solid, gas): Non-applicable *
Autoignition temperature: Non-applicable *
Lower flammability limit: Non-applicable *
Upper flammability limit: Non-applicable *
Explosive (Solid):
Lower explosive limit: Non-applicable *
Upper explosive limit: Non-applicable *
Particle characteristics:
Median equivalent diameter: Non-applicable *
9.2Other information:
Information with regard to physical hazard classes:
Explosive properties: Non-applicable *
Oxidising properties: Non-applicable *
Corrosive to metals: Non-applicable *
Heat of combustion: Non-applicable *
Aerosols-total percentage (by mass) of
flammable components:
Non-applicable *
Other safety characteristics:
Surface tension at 20 C: Non-applicable *
Refraction index: Non-applicable *
*Not relevant due to the nature of the product, not providing information property of its hazards.
SECTION 10: STABILITY AND REACTIVITY
10.1Reactivity:
No hazardous reactions are expected because the product is stable under recommended storage conditions. See
section 7 from Safety Data Sheet.
10.2Chemical stability:
Chemically stable under the indicated conditions of storage, handling and use.
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 5/8
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 10: STABILITY AND REACTIVITY (continued)
10.3Possibility of hazardous reactions:
Under the specified conditions, hazardous reactions that lead to excessive temperatures or pressure are not
expected.
10.4Conditions to avoid:
Applicable for handling and storage at room temperature:
Shock and friction Contact with air Increase in temperature Sunlight Humidity
Not applicable Not applicable Not applicable Not applicable Not applicable
10.5Incompatible materials:
Acids Water Oxidising materials Combustible materials Others
Avoid strong acids Not applicable Not applicable Not applicable
Avoid alkalis or strong
bases
10.6Hazardous decomposition products:
See subsection 10.3, 10.4 and 10.5 to find out the specific decomposition products. Depending on the
decomposition conditions, complex mixtures of chemical substances can be released: carbon dioxide (CO ),
carbon monoxide and other organic compounds.
SECTION 11: TOXICOLOGICAL INFORMATION
11.1Information on toxicological effects:
LD50 oral > 2000 mg/kg (rat)
Dangerous health implications:
In case of exposure that is repetitive, prolonged or at concentrations higher than the recommended occupational
exposure limits, adverse effects on health may result, depending on the means of exposure:
A-Ingestion (acute effect):
– Acute toxicity: Based on available data, the classification criteria are not met
– Corrosivity/Irritability: Based on available data, the classification criteria are not met
B-Inhalation (acute effect):
– Acute toxicity : Based on available data, the classification criteria are not met
– Corrosivity/Irritability: Based on available data, the classification criteria are not met
C-Contact with the skin and the eyes (acute effect):
– Contact with the skin: Based on available data, the classification criteria are not met
– Contact with the eyes: Based on available data, the classification criteria are not met
D-CMR effects (carcinogenicity, mutagenicity and toxicity to reproduction):
– Carcinogenicity: Based on available data, the classification criteria are not met
IARC: Non-applicable
– Mutagenicity: Based on available data, the classification criteria are not met
– Reproductive toxicity: Based on available data, the classification criteria are not met
E-Sensitizing effects:
– Respiratory: Based on available data, the classification criteria are not met
– Skin: Based on available data, the classification criteria are not met
F-Specific target organ toxicity (STOT) – single exposure:
Based on available data, the classification criteria are not met
G-Specific target organ toxicity (STOT)-repeated exposure:
– Specific target organ toxicity (STOT)-repeated exposure: Based on available data, the classification criteria
are not met
– Skin: Based on available data, the classification criteria are not met, as it does not contain substances
classified as hazardous for this effect. For more information see section 3.
H-Aspiration hazard:
Based on available data, the classification criteria are not met
Other information:
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 6/8
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 11: TOXICOLOGICAL INFORMATION (continued)
Non-applicable
Specific toxicology information on the substances:
Not available
SECTION 12: ECOLOGICAL INFORMATION
The experimental information related to the eco-toxicological properties of the product itself is not available
Based on available data, the classification criteria are not met
12.1Toxicity:
Not available
12.2Persistence and degradability:
Not available
12.3Bioaccumulative potential:
Not available
12.4Mobility in soil:
Not available
12.5Results of PBT and vPvB assessment:
Product does not meet PBT/vPvB criteria
12.6Other adverse effects:
Not described
SECTION 13: DISPOSAL CONSIDERATIONS
13.1Waste treatment methods:
Code Description Waste class
It is not possible to assign a specific code, as it depends on the intended use by the
user
Non dangerous
Type of waste:
Non-applicable
Waste management (disposal and evaluation):
Consult the authorized waste service manager on the assessment and disposal operations in accordance The
Waste Regulations 2011, 2011 No. 988. As under 15 01 of the code and in case the container has been in direct
contact with the product, it will be processed the same way as the actual product. Otherwise, it will be processed
as non-dangerous residue. Waste should not be disposed of to drains. See paragraph 6.2.
Regulations related to waste management:
In accordance with Annex II of UK REACH the provisions related to waste management are stated:
UK legislation: The Waste Regulations 2011.
SECTION 14: TRANSPORT INFORMATION
This product is not regulated for transport (ADR/RID,IMDG,IATA)
SECTION 15: REGULATORY INFORMATION
15.1Safety, health and environmental regulations/legislation specific for the substance or mixture:
– Substances listed in UK candidate list of substances of very high concern (SVHCs): Non-applicable
– Substances listed in UK REACH Authorisation List (Annex 14): Non-applicable
The Control of Major Accident Hazards Regulations 2015:
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 7/8
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 15: REGULATORY INFORMATION (continued)
Non-applicable
Restrictions to commercialisation and the use of certain dangerous substances and mixtures (Annex
XVII UK REACH, etc .):
Non-applicable
Specific provisions in terms of protecting people or the environment:
It is recommended to use the information included in this safety data sheet as a basis for conducting workplace-
specific risk assessments in order to establish the necessary risk prevention measures for the handling, use,
storage and disposal of this product.
Other legislation:
The REACH etc. (Amendment etc.) (EU Exit) Regulations 2020.
The Chemicals (Health and Safety) and Genetically Modified Organisms (Contained Use) (Amendment etc.) (EU
Exit) Regulations 2020.
Control of Substances Hazardous to Health Regulations 2002 (as amended)
EH40/2005 Workplace exposure limits.
SECTION 16: OTHER INFORMATION
Legislation related to safety data sheets:
This safety data sheet has been designed in accordance with ANNEX II-The REACH etc. (Amendment etc.) (EU
Exit) Regulations 2020.
Texts of the legislative phrases mentioned in section 3:
The phrases indicated do not refer to the product itself; they are present merely for informative purposes and
refer to the individual components which appear in section 3
GB CLP Regulation:
Non-applicable
Advice related to training:
Training is recommended in order to prevent industrial risks for staff using this product and to facilitate their
comprehension and interpretation of this safety data sheet, as well as the label on the product.
Principal bibliographical sources:
http://echa.europa.eu
http://eur-lex.europa.eu
Abbreviations and acronyms:
ADR: European agreement concerning the international carriage of dangerous goods by road
IMDG: International maritime dangerous goods code
IATA: International Air Transport Association
ICAO: International Civil Aviation Organisation
COD: Chemical Oxygen Demand
BOD5: 5day biochemical oxygen demand
BCF: Bioconcentration factor
LD50: Lethal Dose 50
LC50: Lethal Concentration 50
EC50: Effective concentration 50
LogPOW: Octanolwater partition coefficient
Koc: Partition coefficient of organic carbon
UFI: unique formula identifier
IARC: International Agency for Research on Cancer
Theinformationcontainedinthissafetydatasheetisbasedonsources,technicalknowledgeandcurrentlegislationatUK,withoutbeingabletoguaranteeitsaccuracy.
Thisinformationcannotbeconsideredaguaranteeofthepropertiesoftheproduct,itissimplyadescriptionofthesecurityrequirements.Theoccupationalmethodology
andconditionsforusersofthisproductarenotwithinourawarenessorcontrol,anditisultimatelytheresponsibilityoftheusertotakethenecessarymeasurestoobtain
thelegalrequirementsconcerningthemanipulation,storage,useanddisposalofchemicalproducts.Theinformationonthissafetydatasheetonlyreferstothisproduct,
whichshouldnotbeusedforneedsotherthanthosespecified.
– END OF SAFETY DATA SHEET –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 8/8
by | Sep 27, 2025
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 1: IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKING
1.1Product identifier: BE978 – Epoxy Tooling Board
Not a hazardous substance
CAS: Non-applicable
Other means of identification:
Non-applicable
1.2Relevant identified uses of the substance or mixture and uses advised against:
Relevant uses: Non Hazardous Substance . For industrial user only.
Uses advised against: All uses not specified in this section or in section 7.3
1.3Details of the supplier of the safety data sheet:
Base Materials
Base Materials Ltd,20 Ashville Way
LE8 6NU Leicester – Whetstone – United Kingdom
Phone: 0116 286 5073
sales@base-materials.com
https://www.base-materials.com/
1.4Emergency telephone number: Ecostar Environmental – Reference Code: EREF-00111 : Telephone: +44 800
246 1972 (office hours), WhatsApp: +44 7496 228 905 (office hours), 24/7
Service +44 800 246 1274
SECTION 2: HAZARDS IDENTIFICATION
2.1Classification of the substance or mixture:
When milling: Dust will be produced
GB CLP Regulation:
The product is not classified as hazardous according to GB CLP Regulation.
2.2Label elements:
GB CLP Regulation:
None
2.3Other hazards:
Product does not meet PBT/vPvB criteria
SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS
3.1Substance:
Chemical description: Epoxides
Components:
In accordance with Annex II of The REACH etc. (Amendment etc.) (EU Exit) Regulations 2020, the product
contains:
Identification Chemical name/Classification
Concentratio
n
CAS:Non-applicable
Not a hazardous substance
100 %
To obtain more information on the hazards of the substances consult sections 11, 12 and 16.
3.2Mixture:
Non-applicable
Reaction product based on epoxy
SECTION 4: FIRST AID MEASURES
4.1Description of first aid measures:
Consult a doctor in case of discomfort showing the SDS for the product.
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 1/8
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 4: FIRST AID MEASURES (continued)
By inhalation:
In case of symptoms, move the person affected into fresh air.
By skin contact:
In case of contact it is recommended to clean the affected area thoroughly with water and neutral soap. In case
of changes to the skin (stinging, redness, rashes, blisters, ), seek medical advice with this Safety Data Sheet
By eye contact:
Rinse with water until the product has been eliminated. In case of problems, consult a doctor showing the SDS
for the product.
By ingestion/aspiration:
In case of consumption in large quantities, it is recommended to seek medical assistance.
Dust: Provide fresh air.
4.2Most important symptoms and effects, both acute and delayed:
Acute and delayed effects are indicated in sections 2 and 11.
4.3Indication of any immediate medical attention and special treatment needed:
Non-applicable
SECTION 5: FIREFIGHTING MEASURES
5.1Extinguishing media:
Suitable extinguishing media:
Product is non-flammable, with a low risk of fire due to the flammability characteristics of the product in normal
conditions of storage, handling and use. In the case of the existence of sustained combustion as a result of
improper handling, storage or use any type of extinguishing agent can be used (ABC Powder, water,…)
Unsuitable extinguishing media:
Non-applicable
5.2Special hazards arising from the substance or mixture:
Due to its non-inflammable nature, the product does not present a fire risk under normal conditions of storage,
handling and use.
5.3Advice for firefighters:
Depending on the magnitude of the fire it may be necessary to use full protective clothing and self-contained
breathing apparatus (SCBA). Minimum emergency facilities and equipment should be available (fire blankets,
portable first aid kit,…).
Additional provisions:
Act in accordance with the Internal Emergency Plan and the Information Sheets on actions to take after an
accident or other emergencies. Eliminate all sources of ignition. In case of fire, cool the storage containers and
tanks for products susceptible to combustion, explosion or BLEVE as a result of high temperatures. Avoid spillage
of the products used to extinguish the fire into an aqueous medium.
SECTION 6: ACCIDENTAL RELEASE MEASURES
6.1Personal precautions, protective equipment and emergency procedures:
For non-emergency personnel:
Sweep up and shovel product or collect by other means and place in container for reuse (preferred) or disposal
For emergency responders:
Wear protective equipment. Keep unprotected persons away. See section 8.
Other information:
May form combustible dust concentrations in air. Keep away from sources of ignition – No smoking.
6.2Environmental precautions:
This product is not classified as hazardous to the environment. Keep product away from drains, surface and
ground water.
6.3Methods and material for containment and cleaning up:
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 2/8
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 6: ACCIDENTAL RELEASE MEASURES (continued)
It is recommended:
Sweep up and shovel product or collect by other means and place in container for reuse (preferred) or disposal
6.4Reference to other sections:
See sections 8 and 13.
SECTION 7: HANDLING AND STORAGE
7.1Precautions for safe handling:
A.-General precautions for safe use
Comply with the current legislation concerning the prevention of industrial risks with regards manually
handling weights. Maintain order, cleanliness and dispose of using safe methods (section 6).
B.-Technical recommendations for the prevention of fires and explosions
Due to its non-inflammable nature, the product does not present a fire risk under normal conditions of
storage, handling and use.
C.-Technical recommendations on general occupational hygiene
Do not eat or drink during the process, washing hands afterwards with suitable cleaning products.
D.-Technical recommendations to prevent environmental risks
It is not necessary to take special measures to prevent environmental risks. For more information see
subsection 6.2
Other information:
May form combustible dust concentrations in air. Keep away from sources of ignition – No smoking.
7.2Conditions for safe storage, including any incompatibilities:
A.-Technical measures for storage
Store in a cool, dry, well-ventilated location
B.-General conditions for storage
Avoid sources of heat, radiation, static electricity and contact with food. For additional information see
subsection 10.5
7.3Specific end use(s):
Except for the instructions already specified it is not necessary to provide any special recommendation regarding
the uses of this product.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1Control parameters:
Substances whose occupational exposure limits have to be monitored in the workplace:
Nuisance dust: Inhalable dust 10 mg/m3 // Respirable dust 4 mg/m3
DNEL (Workers):
Non-applicable
DNEL (General population):
Non-applicable
PNEC:
Non-applicable
8.2Exposure controls:
A.-Individual protection measures, such as personal protective equipment
As a preventative measure it is recommended to use basic Personal Protective Equipment, with the
corresponding <>. For more information on Personal Protective Equipment (storage, use,
cleaning, maintenance, class of protection, ) consult the information leaflet provided by the manufacturer. For
more information see subsection 7.1. All information contained herein is a recommendation which needs
some specification from the labour risk prevention services as it is not known whether the company has
additional measures at its disposal.
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 3/8
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION (continued)
B.-Respiratory protection
The use of protection equipment will be necessary if a mist forms or if the occupational exposure limits are
exceeded.
C.-Specific protection for the hands
Pictogram PPE Remarks
Mandatory hand
protection
Protective gloves against minor risks
Replace gloves in case of any sign of damage. For prolonged periods of
exposure to the product for professional users/industrials, we
recommend using CE III gloves in line with standards EN ISO
21420:2020 and EN ISO 374-1:2016+A1:2018
D.-Eye and face protection
Pictogram PPE Remarks
Mandatory face
protection
Panoramic glasses against
splash/projections.
Clean daily and disinfect periodically according to the manufacturer s
instructions. Use if there is a risk of splashing.
E.-Body protection
Pictogram PPE Remarks
Work clothing
Replace before any evidence of deterioration. For periods of prolonged
exposure to the product for professional/industrial users CE III is
recommended, in accordance with the regulations in EN ISO 6529:2013,
EN ISO 6530:2005, EN ISO 13688:2013, EN 464:1994.
Anti-slip work shoes
Replace before any evidence of deterioration. For periods of prolonged
exposure to the product for professional/industrial users CE III is
recommended, in accordance with the regulations in EN ISO
20345:2012 y EN 13832-1:2007
F.-Additional emergency measures
It is not necessary to take additional emergency measures.
Environmental exposure controls:
In accordance with the community legislation for the protection of the environment it is recommended to avoid
environmental spillage of both the product and its container. For additional information see subsection 7.1.D
The Volatile Organic Compounds in Paints, Varnishes and Vehicle Refinishing Products Regulations
2012:
V.O.C. (Supply): 0 % weight
V.O.C. density at 20 C: 0 kg/m (0 g/L)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
9.1Information on basic physical and chemical properties:
For complete information see the product datasheet.
Appearance:
Physical state at 20 C: Solid
Appearance: Not available
Colour: Aqua
Odour: Not available
Odour threshold: Non-applicable *
Volatility:
Boiling point at atmospheric pressure: Non-applicable *
Vapour pressure at 20 C: Non-applicable *
*Not relevant due to the nature of the product, not providing information property of its hazards.
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 4/8
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES (continued)
Vapour pressure at 50 C: Non-applicable *
Evaporation rate at 20 C: Non-applicable *
Product description:
Density at 20 C: ca. 700 kg/m
Relative density at 20 C: ca. 0.7
Dynamic viscosity at 20 C: Non-applicable *
Kinematic viscosity at 20 C: Non-applicable *
Kinematic viscosity at 40 C: Non-applicable *
Concentration: Non-applicable *
pH: Non-applicable *
Vapour density at 20 C: Non-applicable *
Partition coefficient n-octanol/water 20 C: Non-applicable *
Solubility in water at 20 C: Non-applicable *
Solubility properties: Non-applicable *
Decomposition temperature: Non-applicable *
Melting point/freezing point: Non-applicable *
Flammability:
Flash Point: Non-applicable
Flammability (solid, gas): Non-applicable *
Autoignition temperature: Non-applicable *
Lower flammability limit: Non-applicable *
Upper flammability limit: Non-applicable *
Explosive (Solid):
Lower explosive limit: Non-applicable *
Upper explosive limit: Non-applicable *
Particle characteristics:
Median equivalent diameter: Non-applicable *
9.2Other information:
Information with regard to physical hazard classes:
Explosive properties: Non-applicable *
Oxidising properties: Non-applicable *
Corrosive to metals: Non-applicable *
Heat of combustion: Non-applicable *
Aerosols-total percentage (by mass) of
flammable components:
Non-applicable *
Other safety characteristics:
Surface tension at 20 C: Non-applicable *
Refraction index: Non-applicable *
*Not relevant due to the nature of the product, not providing information property of its hazards.
SECTION 10: STABILITY AND REACTIVITY
10.1Reactivity:
No hazardous reactions are expected because the product is stable under recommended storage conditions. See
section 7 from Safety Data Sheet.
10.2Chemical stability:
Chemically stable under the indicated conditions of storage, handling and use.
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 5/8
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 10: STABILITY AND REACTIVITY (continued)
10.3Possibility of hazardous reactions:
Under the specified conditions, hazardous reactions that lead to excessive temperatures or pressure are not
expected.
10.4Conditions to avoid:
Applicable for handling and storage at room temperature:
Shock and friction Contact with air Increase in temperature Sunlight Humidity
Not applicable Not applicable Not applicable Not applicable Not applicable
10.5Incompatible materials:
Acids Water Oxidising materials Combustible materials Others
Avoid strong acids Not applicable Not applicable Not applicable
Avoid alkalis or strong
bases
10.6Hazardous decomposition products:
See subsection 10.3, 10.4 and 10.5 to find out the specific decomposition products. Depending on the
decomposition conditions, complex mixtures of chemical substances can be released: carbon dioxide (CO ),
carbon monoxide and other organic compounds.
SECTION 11: TOXICOLOGICAL INFORMATION
11.1Information on toxicological effects:
LD50 oral > 2000 mg/kg (rat)
Dangerous health implications:
In case of exposure that is repetitive, prolonged or at concentrations higher than the recommended occupational
exposure limits, adverse effects on health may result, depending on the means of exposure:
A-Ingestion (acute effect):
– Acute toxicity: Based on available data, the classification criteria are not met
– Corrosivity/Irritability: Based on available data, the classification criteria are not met
B-Inhalation (acute effect):
– Acute toxicity : Based on available data, the classification criteria are not met
– Corrosivity/Irritability: Based on available data, the classification criteria are not met
C-Contact with the skin and the eyes (acute effect):
– Contact with the skin: Based on available data, the classification criteria are not met
– Contact with the eyes: Based on available data, the classification criteria are not met
D-CMR effects (carcinogenicity, mutagenicity and toxicity to reproduction):
– Carcinogenicity: Based on available data, the classification criteria are not met
IARC: Non-applicable
– Mutagenicity: Based on available data, the classification criteria are not met
– Reproductive toxicity: Based on available data, the classification criteria are not met
E-Sensitizing effects:
– Respiratory: Based on available data, the classification criteria are not met
– Skin: Based on available data, the classification criteria are not met
F-Specific target organ toxicity (STOT) – single exposure:
Based on available data, the classification criteria are not met
G-Specific target organ toxicity (STOT)-repeated exposure:
– Specific target organ toxicity (STOT)-repeated exposure: Based on available data, the classification criteria
are not met
– Skin: Based on available data, the classification criteria are not met, as it does not contain substances
classified as hazardous for this effect. For more information see section 3.
H-Aspiration hazard:
Based on available data, the classification criteria are not met
Other information:
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 6/8
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 11: TOXICOLOGICAL INFORMATION (continued)
Non-applicable
Specific toxicology information on the substances:
Not available
SECTION 12: ECOLOGICAL INFORMATION
The experimental information related to the eco-toxicological properties of the product itself is not available
Based on available data, the classification criteria are not met
12.1Toxicity:
Not available
12.2Persistence and degradability:
Not available
12.3Bioaccumulative potential:
Not available
12.4Mobility in soil:
Not available
12.5Results of PBT and vPvB assessment:
Product does not meet PBT/vPvB criteria
12.6Other adverse effects:
Not described
SECTION 13: DISPOSAL CONSIDERATIONS
13.1Waste treatment methods:
Code Description Waste class
It is not possible to assign a specific code, as it depends on the intended use by the
user
Non dangerous
Type of waste:
Non-applicable
Waste management (disposal and evaluation):
Consult the authorized waste service manager on the assessment and disposal operations in accordance The
Waste Regulations 2011, 2011 No. 988. As under 15 01 of the code and in case the container has been in direct
contact with the product, it will be processed the same way as the actual product. Otherwise, it will be processed
as non-dangerous residue. Waste should not be disposed of to drains. See paragraph 6.2.
Regulations related to waste management:
In accordance with Annex II of UK REACH the provisions related to waste management are stated:
UK legislation: The Waste Regulations 2011.
SECTION 14: TRANSPORT INFORMATION
This product is not regulated for transport (ADR/RID,IMDG,IATA)
SECTION 15: REGULATORY INFORMATION
15.1Safety, health and environmental regulations/legislation specific for the substance or mixture:
– Substances listed in UK candidate list of substances of very high concern (SVHCs): Non-applicable
– Substances listed in UK REACH Authorisation List (Annex 14): Non-applicable
The Control of Major Accident Hazards Regulations 2015:
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 7/8
BE978 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 15: REGULATORY INFORMATION (continued)
Non-applicable
Restrictions to commercialisation and the use of certain dangerous substances and mixtures (Annex
XVII UK REACH, etc .):
Non-applicable
Specific provisions in terms of protecting people or the environment:
It is recommended to use the information included in this safety data sheet as a basis for conducting workplace-
specific risk assessments in order to establish the necessary risk prevention measures for the handling, use,
storage and disposal of this product.
Other legislation:
The REACH etc. (Amendment etc.) (EU Exit) Regulations 2020.
The Chemicals (Health and Safety) and Genetically Modified Organisms (Contained Use) (Amendment etc.) (EU
Exit) Regulations 2020.
Control of Substances Hazardous to Health Regulations 2002 (as amended)
EH40/2005 Workplace exposure limits.
SECTION 16: OTHER INFORMATION
Legislation related to safety data sheets:
This safety data sheet has been designed in accordance with ANNEX II-The REACH etc. (Amendment etc.) (EU
Exit) Regulations 2020.
Texts of the legislative phrases mentioned in section 3:
The phrases indicated do not refer to the product itself; they are present merely for informative purposes and
refer to the individual components which appear in section 3
GB CLP Regulation:
Non-applicable
Advice related to training:
Training is recommended in order to prevent industrial risks for staff using this product and to facilitate their
comprehension and interpretation of this safety data sheet, as well as the label on the product.
Principal bibliographical sources:
http://echa.europa.eu
http://eur-lex.europa.eu
Abbreviations and acronyms:
ADR: European agreement concerning the international carriage of dangerous goods by road
IMDG: International maritime dangerous goods code
IATA: International Air Transport Association
ICAO: International Civil Aviation Organisation
COD: Chemical Oxygen Demand
BOD5: 5day biochemical oxygen demand
BCF: Bioconcentration factor
LD50: Lethal Dose 50
LC50: Lethal Concentration 50
EC50: Effective concentration 50
LogPOW: Octanolwater partition coefficient
Koc: Partition coefficient of organic carbon
UFI: unique formula identifier
IARC: International Agency for Research on Cancer
Theinformationcontainedinthissafetydatasheetisbasedonsources,technicalknowledgeandcurrentlegislationatUK,withoutbeingabletoguaranteeitsaccuracy.
Thisinformationcannotbeconsideredaguaranteeofthepropertiesoftheproduct,itissimplyadescriptionofthesecurityrequirements.Theoccupationalmethodology
andconditionsforusersofthisproductarenotwithinourawarenessorcontrol,anditisultimatelytheresponsibilityoftheusertotakethenecessarymeasurestoobtain
thelegalrequirementsconcerningthemanipulation,storage,useanddisposalofchemicalproducts.Theinformationonthissafetydatasheetonlyreferstothisproduct,
whichshouldnotbeusedforneedsotherthanthosespecified.
– END OF SAFETY DATA SHEET –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 8/8
