ADHESIVES | Revchem Composites

Core-Bond B750R Drum
Liquid.
SAFETY DATA SHEET
GHS product identifier
Product type
Section 1. Identification
:
:
Supplier’s details :
Core-Bond B750R Drum
Relevant identified uses of the substance or mixture and uses advised against
Resins.
Identified uses
Scott Bader ATC,
2400 Canadian Street
Drummondville, Que
Canada, J2C 7W3
Tel: +1 819 477 1752
SB –
Canada
Emergency telephone
number (with hours of
operation)
:
SDS@scottbader.com:e-mail address of person
responsible for this SDS
+1 215 207 0061 (NCEC, Geographic) 24h
+1 866 928 0789 (NCEC, Toll free) 24h
Section 2. Hazards identification
FLAMMABLE LIQUIDS – Category 3
ACUTE TOXICITY (inhalation) – Category 4
SKIN IRRITATION – Category 2
EYE IRRITATION – Category 2A
SKIN SENSITIZATION – Category 1
TOXIC TO REPRODUCTION (Fertility) – Category 2
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Respiratory tract
irritation) – Category 3
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) (hearing organs) –
Category 1
Classification of the
substance or mixture
:
Signal word :Danger
Hazard statements :H226 – Flammable liquid and vapor.
H332 – Harmful if inhaled.
H319 – Causes serious eye irritation.
H315 – Causes skin irritation.
H317 – May cause an allergic skin reaction.
H361 – Suspected of damaging fertility.
H335 – May cause respiratory irritation.
H372 – Causes damage to organs through prolonged or repeated exposure. (hearing
organs)
Hazard pictograms :
Precautionary statements
GHS label elements
OSHA/HCS status :This material is considered hazardous by the OSHA Hazard Communication Standard
(29 CFR 1910.1200).
Date of issue/Date of revision :1/8/2019 Date of previous issue :12/4/2017 Version:1.01 1/14

Core-Bond B750R Drum
Section 2. Hazards identification
Prevention :P201 – Obtain special instructions before use.
P202 – Do not handle until all safety precautions have been read and understood.
P280 – Wear protective gloves. Wear eye or face protection. Wear protective clothing.
P210 – Keep away from heat, hot surfaces, sparks, open flames and other ignition
sources. No smoking.
P241 – Use explosion-proof electrical, ventilating, lighting and all material-handling
equipment.
P242 – Use only non-sparking tools.
P243 – Take precautionary measures against static discharge.
P233 – Keep container tightly closed.
P271 – Use only outdoors or in a well-ventilated area.
P260 – Do not breathe vapor.
P270 – Do not eat, drink or smoke when using this product.
P264 – Wash hands thoroughly after handling.
P272 (OSHA) – Contaminated work clothing must not be allowed out of the workplace.
Response :P314 – Get medical attention if you feel unwell.
P308 + P313 – IF exposed or concerned: Get medical attention.
P304 + P340 + P312 – IF INHALED: Remove person to fresh air and keep comfortable
for breathing. Call a POISON CENTER or physician if you feel unwell.
P303 + P361 + P353 – IF ON SKIN (or hair): Take off immediately all contaminated
clothing. Rinse skin with water or shower.
P302 + P352 + P363 – IF ON SKIN: Wash with plenty of soap and water. Wash
contaminated clothing before reuse.
P333 + P313 – If skin irritation or rash occurs: Get medical attention.
P305 + P351 + P338 – IF IN EYES: Rinse cautiously with water for several minutes.
Remove contact lenses, if present and easy to do. Continue rinsing.
P337 + P313 – If eye irritation persists: Get medical attention.
Storage :P405 – Store locked up.
P403 – Store in a well-ventilated place.
P235 – Keep cool.
Disposal :P501 – Dispose of contents and container in accordance with all local, regional, national
and international regulations.
Hazards not otherwise
classified
:None known.
Section 3. Composition/information on ingredients
styrene 32.335 100-42-5
cobalt bis(2-ethylhexanoate) 0.11184 136-52-7
Ingredient name CAS number%
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health or the environment and hence require reporting
in this section.
Other means of
identification
:Not available.
CAS number :Not applicable.
Substance/mixture
Product code :CC750E02
CAS number/other identifiers
:
Occupational exposure limits, if available, are listed in Section 8.
Mixture
Any concentration shown as a range is to protect confidentiality or is due to batch variation.
Date of issue/Date of revision :1/8/2019 Date of previous issue :12/4/2017 Version:1.01 2/14

Core-Bond B750R Drum
Wash out mouth with water. Remove dentures if any. Remove victim to fresh air and
keep at rest in a position comfortable for breathing. If material has been swallowed and
the exposed person is conscious, give small quantities of water to drink. Stop if the
exposed person feels sick as vomiting may be dangerous. Do not induce vomiting
unless directed to do so by medical personnel. If vomiting occurs, the head should be
kept low so that vomit does not enter the lungs. Get medical attention. Never give
anything by mouth to an unconscious person. If unconscious, place in recovery position
and get medical attention immediately. Maintain an open airway. Loosen tight clothing
such as a collar, tie, belt or waistband.
Immediately flush eyes with plenty of water, occasionally lifting the upper and lower
eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10
minutes. Get medical attention.
Wash with plenty of soap and water. Remove contaminated clothing and shoes. Wash
contaminated clothing thoroughly with water before removing it, or wear gloves.
Continue to rinse for at least 10 minutes. Get medical attention. In the event of any
complaints or symptoms, avoid further exposure. Wash clothing before reuse. Clean
shoes thoroughly before reuse.
Remove victim to fresh air and keep at rest in a position comfortable for breathing. If it
is suspected that fumes are still present, the rescuer should wear an appropriate mask
or self-contained breathing apparatus. If not breathing, if breathing is irregular or if
respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It
may be dangerous to the person providing aid to give mouth-to-mouth resuscitation.
Get medical attention. If necessary, call a poison center or physician. If unconscious,
place in recovery position and get medical attention immediately. Maintain an open
airway. Loosen tight clothing such as a collar, tie, belt or waistband.
Section 4. First aid measures
Eye contact
Skin contact
Inhalation
Ingestion :
:
:
:
Notes to physician :Treat symptomatically. Contact poison treatment specialist immediately if large
quantities have been ingested or inhaled.
Description of necessary first aid measures
Most important symptoms/effects, acute and delayed
Inhalation :Harmful if inhaled. May cause respiratory irritation.
No known significant effects or critical hazards.:Ingestion
Skin contact :Causes skin irritation. May cause an allergic skin reaction.
Causes serious eye irritation.:Eye contact
Over-exposure signs/symptoms
Skin contact
Ingestion
Inhalation Adverse symptoms may include the following:
respiratory tract irritation
coughing
reduced fetal weight
increase in fetal deaths
skeletal malformations
Adverse symptoms may include the following:
reduced fetal weight
increase in fetal deaths
skeletal malformations
Adverse symptoms may include the following:
irritation
redness
reduced fetal weight
increase in fetal deaths
skeletal malformations
:
:
:
Eye contact :Adverse symptoms may include the following:
pain or irritation
watering
redness
Potential acute health effects
Indication of immediate medical attention and special treatment needed, if necessary
Date of issue/Date of revision :1/8/2019 Date of previous issue :12/4/2017 Version:1.01 3/14

Core-Bond B750R Drum
Section 4. First aid measures
Protection of first-aiders:No action shall be taken involving any personal risk or without suitable training. If it is
suspected that fumes are still present, the rescuer should wear an appropriate mask or
self-contained breathing apparatus. It may be dangerous to the person providing aid to
give mouth-to-mouth resuscitation. Wash contaminated clothing thoroughly with water
before removing it, or wear gloves.
Specific treatments :No specific treatment.
See toxicological information (Section 11)
Section 5. Fire-fighting measures
Promptly isolate the scene by removing all persons from the vicinity of the incident if
there is a fire. No action shall be taken involving any personal risk or without suitable
training. Move containers from fire area if this can be done without risk. Use water
spray to keep fire-exposed containers cool.
Hazardous thermal
decomposition products
Specific hazards arising
from the chemical
Decomposition products may include the following materials:
carbon dioxide
carbon monoxide
metal oxide/oxides
Flammable liquid and vapor. Runoff to sewer may create fire or explosion hazard. In a
fire or if heated, a pressure increase will occur and the container may burst, with the risk
of a subsequent explosion.
Fire-fighters should wear appropriate protective equipment and self-contained breathing
apparatus (SCBA) with a full face-piece operated in positive pressure mode.
Special protective
equipment for fire-fighters
Use dry chemical, CO , water spray (fog) or foam.
Extinguishing media
:
:
:
Do not use water jet.
Suitable extinguishing
media
:
Unsuitable extinguishing
media
:
Special protective actions
for fire-fighters
:
Section 6. Accidental release measures
Environmental precautions
Personal precautions, protective equipment and emergency procedures
:
:No action shall be taken involving any personal risk or without suitable training.
Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilled material. Shut off all ignition sources.
No flares, smoking or flames in hazard area. Avoid breathing vapor or mist. Provide
adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put
on appropriate personal protective equipment.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air).
Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Dilute with water and mop up if water-soluble. Alternatively,
or if water-insoluble, absorb with an inert dry material and place in an appropriate waste
disposal container. Dispose of via a licensed waste disposal contractor.
Small spill :
Methods and materials for containment and cleaning up
For non-emergency
personnel
For emergency responders:If specialized clothing is required to deal with the spillage, take note of any information in
Section 8 on suitable and unsuitable materials. See also the information in “For non-
emergency personnel”.
Date of issue/Date of revision :1/8/2019 Date of previous issue :12/4/2017 Version:1.01 4/14

Core-Bond B750R Drum
Section 6. Accidental release measures
Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Approach release from upwind. Prevent entry into sewers,
water courses, basements or confined areas. Wash spillages into an effluent treatment
plant or proceed as follows. Contain and collect spillage with non-combustible,
absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in
container for disposal according to local regulations (see Section 13). Dispose of via a
licensed waste disposal contractor. Contaminated absorbent material may pose the
same hazard as the spilled product. Note: see Section 1 for emergency contact
information and Section 13 for waste disposal.
Large spill :
Section 7. Handling and storage
Advice on general
occupational hygiene
Conditions for safe storage,
including any
incompatibilities
Eating, drinking and smoking should be prohibited in areas where this material is
handled, stored and processed. Workers should wash hands and face before eating,
drinking and smoking. Remove contaminated clothing and protective equipment before
entering eating areas. See also Section 8 for additional information on hygiene
measures.
Store in accordance with local regulations. Store in a segregated and approved area.
Store in original container protected from direct sunlight in a dry, cool and well-ventilated
area, away from incompatible materials (see Section 10) and food and drink. Store
locked up. Eliminate all ignition sources. Separate from oxidizing materials. Keep
container tightly closed and sealed until ready for use. Containers that have been
opened must be carefully resealed and kept upright to prevent leakage. Do not store in
unlabeled containers. Use appropriate containment to avoid environmental
contamination.
:
:
Protective measures Put on appropriate personal protective equipment (see Section 8). Persons with a
history of skin sensitization problems should not be employed in any process in which
this product is used. Avoid exposure – obtain special instructions before use. Avoid
exposure during pregnancy. Do not handle until all safety precautions have been read
and understood. Do not get in eyes or on skin or clothing. Do not breathe vapor or mist.
Do not ingest. Use only with adequate ventilation. Wear appropriate respirator when
ventilation is inadequate. Do not enter storage areas and confined spaces unless
adequately ventilated. Keep in the original container or an approved alternative made
from a compatible material, kept tightly closed when not in use. Store and use away
from heat, sparks, open flame or any other ignition source. Use explosion-proof
electrical (ventilating, lighting and material handling) equipment. Use only non-sparking
tools. Take precautionary measures against electrostatic discharges. Empty containers
retain product residue and can be hazardous. Do not reuse container.
:
Precautions for safe handling
styrene ACGIH TLV (United States, 3/2016).
TWA: 20 ppm 8 hours.
TWA: 85 mg/m 8 hours.
STEL: 40 ppm 15 minutes.
STEL: 170 mg/m 15 minutes.
OSHA PEL 1989 (United States, 3/1989).
TWA: 50 ppm 8 hours.
TWA: 215 mg/m 8 hours.
STEL: 100 ppm 15 minutes.
STEL: 425 mg/m 15 minutes.
OSHA PEL Z2 (United States, 2/2013).
TWA: 100 ppm 8 hours.
CEIL: 200 ppm
AMP: 600 ppm 5 minutes.
NIOSH REL (United States, 10/2016).
TWA: 50 ppm 10 hours.
Section 8. Exposure controls/personal protection
Ingredient name Exposure limits
Control parameters
Occupational exposure limits
Date of issue/Date of revision :1/8/2019 Date of previous issue :12/4/2017 Version:1.01 5/14

Core-Bond B750R Drum
Section 8. Exposure controls/personal protection
TWA: 215 mg/m 10 hours.
STEL: 100 ppm 15 minutes.
STEL: 425 mg/m 15 minutes.
cobalt bis(2-ethylhexanoate) ACGIH TLV (United States, 3/2016).
TWA: 0.02 mg/m , (as Co) 8 hours.
Hand protection
Based on the hazard and potential for exposure, select a respirator that meets the
appropriate standard or certification. Respirators must be used according to a
respiratory protection program to ensure proper fitting, training, and other important
aspects of use.
Chemical-resistant, impervious gloves complying with an approved standard should be
worn at all times when handling chemical products if a risk assessment indicates this is
necessary. Considering the parameters specified by the glove manufacturer, check
during use that the gloves are still retaining their protective properties. It should be
noted that the time to breakthrough for any glove material may be different for different
glove manufacturers. In the case of mixtures, consisting of several substances, the
protection time of the gloves cannot be accurately estimated.
Safety eyewear complying with an approved standard should be used when a risk
assessment indicates this is necessary to avoid exposure to liquid splashes, mists,
gases or dusts. If contact is possible, the following protection should be worn, unless
the assessment indicates a higher degree of protection: chemical splash goggles.
Eye/face protection
Respiratory protection :
:
:
Body protection Personal protective equipment for the body should be selected based on the task being
performed and the risks involved and should be approved by a specialist before
handling this product. When there is a risk of ignition from static electricity, wear anti-
static protective clothing. For the greatest protection from static discharges, clothing
should include anti-static overalls, boots and gloves.
:
Environmental exposure
controls
:Emissions from ventilation or work process equipment should be checked to ensure
they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process equipment
will be necessary to reduce emissions to acceptable levels.
Appropriate engineering
controls
:Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or
other engineering controls to keep worker exposure to airborne contaminants below any
recommended or statutory limits. The engineering controls also need to keep gas,
vapor or dust concentrations below any lower explosive limits. Use explosion-proof
ventilation equipment.
Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Contaminated work clothing should not be allowed out of the workplace. Wash
contaminated clothing before reusing. Ensure that eyewash stations and safety
showers are close to the workstation location.
Hygiene measures :
Individual protection measures
Skin protection
Other skin protection :Appropriate footwear and any additional skin protection measures should be selected
based on the task being performed and the risks involved and should be approved by a
specialist before handling this product.
Section 9. Physical and chemical properties
Physical state
Melting point
Liquid.
Not available.
SolventOdor
pH
White.Color
Not available.
Not available.Odor threshold
:
:
:
:
:
:
Appearance
Date of issue/Date of revision :1/8/2019 Date of previous issue :12/4/2017 Version:1.01 6/14

Core-Bond B750R Drum
Section 9. Physical and chemical properties
Vapor pressure
Relative density
Vapor density
Solubility
0.7 to 0.8
Not available.
Not available.
Not available.
Evaporation rate Not available.
Auto-ignition temperature
Flash point
Not available.
Closed cup: 31 C (87.8 F)
Not available.
Viscosity Kinematic (40 C (104 F)): >0.4 cm
2
/s (>40 cSt)
Partition coefficient: n-
octanol/water
:
:
:
:
:
:
:
:
:
Boiling point :Not available.
Flammability (solid, gas):Not available.
Lower and upper explosive
(flammable) limits
:Not available.
Burning rate Not applicable.:
Burning time :Not applicable.
SADT Not available.:
Decomposition temperature:Not available.
Aerosol product
Solubility in water :Not available.
Section 10. Stability and reactivity
Hazardous decomposition
products
Conditions to avoid Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld,
braze, solder, drill, grind or expose containers to heat or sources of ignition.
Under normal conditions of storage and use, hazardous decomposition products should
not be produced.
The product is stable.Chemical stability
Reactive or incompatible with the following materials:
oxidizing materials
:
:
:
Incompatible materials :
Possibility of hazardous
reactions
:Under normal conditions of storage and use, hazardous reactions will not occur.
Reactivity :No specific test data related to reactivity available for this product or its ingredients.
Section 11. Toxicological information
Acute toxicity
styrene LC50 Inhalation Gas. Rat 2770 ppm 4 hours
LC50 Inhalation Vapor Rat 11800 mg/m 4 hours
LD50 Dermal Rat >2000 mg/kg –
LD50 Oral Rat 2650 mg/kg –
cobalt bis(2-ethylhexanoate)LD50 Dermal Rabbit >5 g/kg –
LD50 Oral Rat >2000 mg/kg –
Product/ingredient name Result Species Dose Exposure
Irritation/Corrosion
Information on toxicological effects
Date of issue/Date of revision :1/8/2019 Date of previous issue :12/4/2017 Version:1.01 7/14

Core-Bond B750R Drum
Section 11. Toxicological information
Carcinogenicity
Not available.
Mutagenicity
Not available.
Teratogenicity
Not available.
Reproductive toxicity
Not available.
styrene Eyes – Mild irritant Human – 50 parts per
million
–
Eyes – Moderate irritantRabbit – 24 hours 100
milligrams
–
Eyes – Severe irritantRabbit – 100
milligrams
–
Skin – Mild irritant Rabbit – 500
milligrams
–
Skin – Moderate irritantRabbit – 100 Percent-
Product/ingredient name Result Score Exposure Observation
Sensitization
Not available.
Species
Information on the likely
routes of exposure
Inhalation :Harmful if inhaled. May cause respiratory irritation.
No known significant effects or critical hazards.:Ingestion
Skin contact :Causes skin irritation. May cause an allergic skin reaction.
Causes serious eye irritation.:Eye contact
Symptoms related to the physical, chemical and toxicological characteristics
Specific target organ toxicity (single exposure)
Specific target organ toxicity (repeated exposure)
styrene Category 3 Not applicable.Respiratory tract
irritation
Name Category
Name Category
styrene Category 1 Inhalation hearing organs
Aspiration hazard
Name Result
styrene ASPIRATION HAZARD – Category 1
Route of
exposure
Target organs
Route of
exposure
Target organs
:Not available.
Potential acute health effects
Classification
styrene – 2B Reasonably anticipated to be a human carcinogen.
cobalt bis(2-ethylhexanoate)- 2B Reasonably anticipated to be a human carcinogen.
Product/ingredient name NTPIARCOSHA
Date of issue/Date of revision :1/8/2019 Date of previous issue :12/4/2017 Version:1.01 8/14

Core-Bond B750R Drum
Section 11. Toxicological information
styrene Chronic NOAEL Dermal Rat 615 mg/kg –
Chronic NOAEL Inhalation
Gas.
Rat 20 ppm 8 hours
Product/ingredient name Result Species Dose Exposure
Causes damage to organs through prolonged or repeated exposure. Once sensitized, a
severe allergic reaction may occur when subsequently exposed to very low levels.
General :
No known significant effects or critical hazards.Carcinogenicity :
No known significant effects or critical hazards.Mutagenicity :
No known significant effects or critical hazards.Teratogenicity :
Developmental effects :No known significant effects or critical hazards.
Fertility effects :Suspected of damaging fertility.
Skin contact
Ingestion
Inhalation Adverse symptoms may include the following:
respiratory tract irritation
coughing
reduced fetal weight
increase in fetal deaths
skeletal malformations
Adverse symptoms may include the following:
reduced fetal weight
increase in fetal deaths
skeletal malformations
Adverse symptoms may include the following:
irritation
redness
reduced fetal weight
increase in fetal deaths
skeletal malformations
:
:
:
Eye contact :Adverse symptoms may include the following:
pain or irritation
watering
redness
Potential chronic health effects
Delayed and immediate effects and also chronic effects from short and long term exposure
Numerical measures of toxicity
Oral 7073.9 mg/kg
Inhalation (gases) 7033.7 ppm
Inhalation (vapors) 29.96 mg/l
Route ATE value
Acute toxicity estimates
Potential immediate
effects
:Not available.
Short term exposure
Potential delayed effects:Not available.
Potential immediate
effects
:Not available.
Long term exposure
Potential delayed effects:Not available.
Date of issue/Date of revision :1/8/2019 Date of previous issue :12/4/2017 Version:1.01 9/14

Core-Bond B750R Drum
Section 12. Ecological information
LogPow BCF Potential
Bioaccumulative potential
Other adverse effects :No known significant effects or critical hazards.
Product/ingredient name
styrene 0.35 13.49 low
cobalt bis(2-ethylhexanoate)- 15600 high
Product/ingredient name Aquatic half-life Photolysis Biodegradability
styrene – – Readily
cobalt bis(2-ethylhexanoate)- – Not readily
Toxicity
styrene Acute EC50 1400 g/l Fresh water Algae – Pseudokirchneriella
subcapitata
72 hours
Acute EC50 33 mg/l Fresh water Algae – Pseudokirchneriella
subcapitata
96 hours
Acute EC50 4700 g/l Fresh water Daphnia – Daphnia magna 48 hours
Acute LC50 52 mg/l Marine water Crustaceans – Artemia salina48 hours
Acute LC50 4020 g/l Fresh water Fish – Pimephales promelas 96 hours
Chronic NOEC 1.01 mg/l Daphnia 21 days
Product/ingredient name SpeciesResult Exposure
Persistence and degradability
Soil/water partition
coefficient (KOC)
:Not available.
Mobility in soil
Section 13. Disposal considerations
The generation of waste should be avoided or minimized wherever possible. Disposal
of this product, solutions and any by-products should at all times comply with the
requirements of environmental protection and waste disposal legislation and any
regional local authority requirements. Dispose of surplus and non-recyclable products
via a licensed waste disposal contractor. Waste should not be disposed of untreated to
the sewer unless fully compliant with the requirements of all authorities with jurisdiction.
Waste packaging should be recycled. Incineration or landfill should only be considered
when recycling is not feasible. This material and its container must be disposed of in a
safe way. Care should be taken when handling emptied containers that have not been
cleaned or rinsed out. Empty containers or liners may retain some product residues.
Vapor from product residues may create a highly flammable or explosive atmosphere
inside the container. Do not cut, weld or grind used containers unless they have been
cleaned thoroughly internally. Avoid dispersal of spilled material and runoff and contact
with soil, waterways, drains and sewers.
:Disposal methods
Section 14. Transport information
Resin solution RESIN
SOLUTION
Resin solution
UN1866UN1866 UN1866
DOT
Classification
IMDG IATA
UN number
UN proper
shipping name
TDG
Classification
UN1866
RESIN
SOLUTION
ADR/RID
UN1866
RESIN
SOLUTION
Mexico
Classification
UN1866
RESINA,
SOLUCIONES
DE
Date of issue/Date of revision :1/8/2019 Date of previous issue :12/4/2017 Version:1.01 10/14

Core-Bond B750R Drum
Section 14. Transport information
3
III
3
III
3
III
Reportable
quantity 3092.
6 lbs / 1404 kg
[494.55 gal /
1872.1 L].
Package sizes
shipped in
quantities less
than the
product
reportable
quantity are
not subject to
the RQ
(reportable
quantity)
transportation
requirements.
Limited
quantity Yes.
Packaging
instruction
Exceptions:
150. Non-bulk:
173. Bulk: 242.
Quantity
limitation
Passenger
aircraft/rail: 60
L. Cargo
aircraft: 220 L.
Special
provisions B1,
B52, IB3, T2,
TP1
Emergency
schedules F-E,
_S-E_
Special
provisions
223, 955
Quantity
limitation
Passenger and
Cargo Aircraft:
60 L.
Packaging
instructions:
355. Cargo
Aircraft Only:
220 L.
Packaging
instructions:
366. Limited
Quantities –
Passenger
Aircraft: 10 L.
Packaging
instructions:
Y344.
Special
provisions A3
Transport
hazard class(es)
Packing group
Additional
information
Environmental
hazards
Special precautions for user
Transport in bulk according
to Annex II of MARPOL and
the IBC Code
No. No. No.
Transport within user s premises: always transport in closed containers that are
upright and secure. Ensure that persons transporting the product know what to do in the
event of an accident or spillage.
:Not available.
:
3
III
No.
Product
classified as
per the
following
sections of the
Transportation
of Dangerous
Goods
Regulations: 2.
18-2.19 (Class
3).
Explosive
Limit and
Limited
Quantity Index
5
Passenger
Carrying
Road or Rail
Index 60
3
III
No.
Hazard
identification
number 30
Limited
quantity 5 L
Special
provisions
640E
Tunnel code
(D/E)
3
III
No.
Special
provisions 223
Date of issue/Date of revision :1/8/2019 Date of previous issue :12/4/2017 Version:1.01 11/14

Core-Bond B750R Drum
Section 15. Regulatory information
U.S. Federal regulations
The following components are listed: STYRENE; PHENYLETHYLENE; FIBROUS
GLASS
Massachusetts
:
:
SARA 313
Product name CAS number %
SARA 313 notifications must not be detached from the SDS and any copying and redistribution of the SDS shall include
copying and redistribution of the notice attached to copies of the SDS subsequently redistributed.
styrene 100-42-5 32.335
cobalt bis(2-ethylhexanoate) 136-52-7 0.11184
styrene 100-42-5 32.335
cobalt bis(2-ethylhexanoate) 136-52-7 0.11184
Form R – Reporting
requirements
Supplier notification
Clean Air Act Section 112
(b) Hazardous Air
Pollutants (HAPs)
:Listed
Clean Air Act Section 602
Class I Substances
:Not listed
Clean Air Act Section 602
Class II Substances
:Not listed
DEA List I Chemicals
(Precursor Chemicals)
:Not listed
DEA List II Chemicals
(Essential Chemicals)
:Not listed
New York :The following components are listed: Styrene
State regulations
TSCA 8(a) PAIR: 4-tert-butylpyrocatechol; N,N-dimethylaniline
TSCA 8(a) CDR Exempt/Partial exemption: Not determined
SARA 302/304
SARA 304 RQ :933706816.1 lbs / 423902894.5 kg [149311063.3 gal / 565203859.3 L]
acrylonitrile <0.0000119Yes.10000 1488 100 14.9 methacrylonitrile <0.0000119Yes.500 75 1000 149.9 aniline 0. 000001365 - 0. 00001365 Yes.1000 117.6 5000 587.9 Composition/information on ingredients Name % EHS(lbs) (lbs)(gallons) (gallons) SARA 302 TPQ SARA 304 RQ SARA 311/312 Classification :Fire hazard Immediate (acute) health hazard Delayed (chronic) health hazard styrene 32.335 Yes. No. No. Yes. Yes. cobalt bis(2-ethylhexanoate) 0.11184 No. No. No. Yes. Yes. Name % Fire hazard Sudden release of pressure Reactive Immediate (acute) health hazard Delayed (chronic) health hazard Composition/information on ingredients Date of issue/Date of revision :1/8/2019 Date of previous issue :12/4/2017 Version:1.01 12/14 Core-Bond B750R Drum Section 15. Regulatory information WARNING: This product contains a chemical known to the State of California to cause cancer. WARNING: This product contains less than 1% of a chemical known to the State of California to cause birth defects or other reproductive harm. acrylonitrile Yes. No. Yes. - styrene Yes. No. - - ethanediol No. Yes. - - aniline Yes. No. Yes. - Ingredient name Cancer Reproductive No significant risk level Maximum acceptable dosage level California Prop. 65 New Jersey :The following components are listed: STYRENE MONOMER; BENZENE, ETHENYL-; COBALT compounds Pennsylvania :The following components are listed: BENZENE, ETHENYL-; COBALT COMPOUNDS International regulations Montreal Protocol (Annexes A, B, C, E) Not listed. Stockholm Convention on Persistent Organic Pollutants Not listed. Rotterdam Convention on Prior Informed Consent (PIC) Not listed. Chemical Weapon Convention List Schedules I, II & III Chemicals Not listed. UNECE Aarhus Protocol on POPs and Heavy Metals Not listed. International lists National inventoryNot determined Section 16. Other information Hazardous Material Information System (U.S.A.) 3 3 0 0 3 2 * National Fire Protection Association (U.S.A.) Health Special Instability/Reactivity Flammability Health Flammability Physical hazards Caution: HMIS ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4 representing significant hazards or risks. Although HMIS ratings and the associated label are not required on SDSs or products leaving a facility under 29 CFR 1910.1200, the preparer may choose to provide them. HMIS ratings are to be used with a fully implemented HMIS program. HMIS is a registered trademark and service mark of the American Coatings Association, Inc. The customer is responsible for determining the PPE code for this material. For more information on HMIS Personal Protective Equipment (PPE) codes, consult the HMIS Implementation Manual. Reprinted with permission from NFPA 704-2001, Identification of the Hazards of Materials for Emergency Response Copyright 1997, National Fire Protection Association, Quincy, MA 02269. This reprinted material is not the complete and official position of the National Fire Protection Association, on the referenced subject which is represented only by the standard in its entirety. Date of issue/Date of revision :1/8/2019 Date of previous issue :12/4/2017 Version:1.01 13/14 Core-Bond B750R Drum Section 16. Other information 1/8/2019 History Date of printing Date of issue/Date of revision Version To the best of our knowledge, the information contained herein is accurate. However, neither the above-named supplier, nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist. Notice to reader Date of previous issue : : : : Indicates information that has changed from previously issued version. References :Not available. Key to abbreviations :ATE = Acute Toxicity Estimate BCF = Bioconcentration Factor GHS = Globally Harmonized System of Classification and Labelling of Chemicals IATA = International Air Transport Association IBC = Intermediate Bulk Container IMDG = International Maritime Dangerous Goods LogPow = logarithm of the octanol/water partition coefficient MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution) UN = United Nations 1/8/2019 12/4/2017 1.01 Copyright 2001, National Fire Protection Association, Quincy, MA 02269. This warning system is intended to be interpreted and applied only by properly trained individuals to identify fire, health and reactivity hazards of chemicals. The user is referred to certain limited number of chemicals with recommended classifications in NFPA 49 and NFPA 325, which would be used as a guideline only. Whether the chemicals are classified by NFPA or not, anyone using the 704 systems to classify chemicals does so at their own risk. Date of issue/Date of revision :1/8/2019 Date of previous issue :12/4/2017 Version:1.01 14/14

23B73RF_SDS.pdf

by | Sep 27, 2025

Core-Bond B73 R
Liquid.
SAFETY DATA SHEET
GHS product identifier
Product type
Section 1. Identification
:
:
Supplier’s details :
Core-Bond B73 R
Relevant identified uses of the substance or mixture and uses advised against
Resins.
Identified uses
Scott Bader ATC,
2400 Canadian Street
Drummondville, Que
Canada, J2C 7W3
Tel: +1 819 477 1752
SB –
Canada
Emergency telephone
number (with hours of
operation)
:
SDS@scottbader.com:e-mail address of person
responsible for this SDS
+1 215 207 0061 (NCEC, Geographic) 24h
+1 866 928 0789 (NCEC, Toll free) 24h
Section 2. Hazards identification
FLAMMABLE LIQUIDS – Category 3
ACUTE TOXICITY (inhalation) – Category 4
SKIN IRRITATION – Category 2
EYE IRRITATION – Category 2A
CARCINOGENICITY – Category 2
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Respiratory tract
irritation) – Category 3
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) (hearing organs) –
Category 1
Classification of the
substance or mixture
:
Signal word :Danger
Hazard statements :H226 – Flammable liquid and vapor.
H332 – Harmful if inhaled.
H319 – Causes serious eye irritation.
H315 – Causes skin irritation.
H351 – Suspected of causing cancer.
H335 – May cause respiratory irritation.
H372 – Causes damage to organs through prolonged or repeated exposure. (hearing
organs)
Hazard pictograms :
Precautionary statements
GHS label elements
OSHA/HCS status :This material is considered hazardous by the OSHA Hazard Communication Standard
(29 CFR 1910.1200).
Date of issue/Date of revision :1/8/2019 Date of previous issue :3/5/2016 Version:1.05 1/14

Core-Bond B73 R
Section 2. Hazards identification
Prevention :P201 – Obtain special instructions before use.
P202 – Do not handle until all safety precautions have been read and understood.
P280 – Wear protective gloves. Wear eye or face protection. Wear protective clothing.
P210 – Keep away from heat, hot surfaces, sparks, open flames and other ignition
sources. No smoking.
P241 – Use explosion-proof electrical, ventilating, lighting and all material-handling
equipment.
P242 – Use only non-sparking tools.
P243 – Take precautionary measures against static discharge.
P233 – Keep container tightly closed.
P271 – Use only outdoors or in a well-ventilated area.
P260 – Do not breathe vapor.
P270 – Do not eat, drink or smoke when using this product.
P264 – Wash hands thoroughly after handling.
Response :P314 – Get medical attention if you feel unwell.
P308 + P313 – IF exposed or concerned: Get medical attention.
P304 + P340 + P312 – IF INHALED: Remove person to fresh air and keep comfortable
for breathing. Call a POISON CENTER or physician if you feel unwell.
P303 + P361 + P353 – IF ON SKIN (or hair): Take off immediately all contaminated
clothing. Rinse skin with water or shower.
P302 + P352 + P362+P364 – IF ON SKIN: Wash with plenty of soap and water. Take off
contaminated clothing and wash it before reuse.
P332 + P313 – If skin irritation occurs: Get medical attention.
P305 + P351 + P338 – IF IN EYES: Rinse cautiously with water for several minutes.
Remove contact lenses, if present and easy to do. Continue rinsing.
P337 + P313 – If eye irritation persists: Get medical attention.
Storage :P405 – Store locked up.
P403 – Store in a well-ventilated place.
P235 – Keep cool.
Disposal :P501 – Dispose of contents and container in accordance with all local, regional, national
and international regulations.
Hazards not otherwise
classified
:None known.
Section 3. Composition/information on ingredients
styrene 30.067 100-42-5
N,N-dimethylaniline 0.1323 121-69-7
Ingredient name CAS number%
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health or the environment and hence require reporting
in this section.
Other means of
identification
:Not available.
CAS number :Not applicable.
Substance/mixture
Product code :CC073E00
CAS number/other identifiers
:
Occupational exposure limits, if available, are listed in Section 8.
Mixture
Any concentration shown as a range is to protect confidentiality or is due to batch variation.
Date of issue/Date of revision :1/8/2019 Date of previous issue :3/5/2016 Version:1.05 2/14

Core-Bond B73 R
Wash out mouth with water. Remove dentures if any. Remove victim to fresh air and
keep at rest in a position comfortable for breathing. If material has been swallowed and
the exposed person is conscious, give small quantities of water to drink. Stop if the
exposed person feels sick as vomiting may be dangerous. Do not induce vomiting
unless directed to do so by medical personnel. If vomiting occurs, the head should be
kept low so that vomit does not enter the lungs. Get medical attention. Never give
anything by mouth to an unconscious person. If unconscious, place in recovery position
and get medical attention immediately. Maintain an open airway. Loosen tight clothing
such as a collar, tie, belt or waistband.
Immediately flush eyes with plenty of water, occasionally lifting the upper and lower
eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10
minutes. Get medical attention.
Flush contaminated skin with plenty of water. Remove contaminated clothing and
shoes. Continue to rinse for at least 10 minutes. Get medical attention. Wash clothing
before reuse. Clean shoes thoroughly before reuse.
Remove victim to fresh air and keep at rest in a position comfortable for breathing. If it
is suspected that fumes are still present, the rescuer should wear an appropriate mask
or self-contained breathing apparatus. If not breathing, if breathing is irregular or if
respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It
may be dangerous to the person providing aid to give mouth-to-mouth resuscitation.
Get medical attention. If necessary, call a poison center or physician. If unconscious,
place in recovery position and get medical attention immediately. Maintain an open
airway. Loosen tight clothing such as a collar, tie, belt or waistband.
Section 4. First aid measures
Eye contact
Skin contact
Inhalation
Ingestion :
:
:
:
Protection of first-aiders:No action shall be taken involving any personal risk or without suitable training. If it is
suspected that fumes are still present, the rescuer should wear an appropriate mask or
self-contained breathing apparatus. It may be dangerous to the person providing aid to
give mouth-to-mouth resuscitation.
Notes to physician :Treat symptomatically. Contact poison treatment specialist immediately if large
quantities have been ingested or inhaled.
Description of necessary first aid measures
Specific treatments :No specific treatment.
Most important symptoms/effects, acute and delayed
Inhalation :Harmful if inhaled. May cause respiratory irritation.
No known significant effects or critical hazards.:Ingestion
Skin contact :Causes skin irritation.
Causes serious eye irritation.:Eye contact
Over-exposure signs/symptoms
Skin contact
Ingestion
Inhalation Adverse symptoms may include the following:
respiratory tract irritation
coughing
No specific data.
Adverse symptoms may include the following:
irritation
redness
:
:
:
Eye contact :Adverse symptoms may include the following:
pain or irritation
watering
redness
Potential acute health effects
See toxicological information (Section 11)
Indication of immediate medical attention and special treatment needed, if necessary
Date of issue/Date of revision :1/8/2019 Date of previous issue :3/5/2016 Version:1.05 3/14

Core-Bond B73 R
Section 5. Fire-fighting measures
Promptly isolate the scene by removing all persons from the vicinity of the incident if
there is a fire. No action shall be taken involving any personal risk or without suitable
training. Move containers from fire area if this can be done without risk. Use water
spray to keep fire-exposed containers cool.
Hazardous thermal
decomposition products
Specific hazards arising
from the chemical
Decomposition products may include the following materials:
carbon dioxide
carbon monoxide
metal oxide/oxides
Flammable liquid and vapor. Runoff to sewer may create fire or explosion hazard. In a
fire or if heated, a pressure increase will occur and the container may burst, with the risk
of a subsequent explosion.
Fire-fighters should wear appropriate protective equipment and self-contained breathing
apparatus (SCBA) with a full face-piece operated in positive pressure mode.
Special protective
equipment for fire-fighters
Use dry chemical, CO , water spray (fog) or foam.
Extinguishing media
:
:
:
Do not use water jet.
Suitable extinguishing
media
:
Unsuitable extinguishing
media
:
Special protective actions
for fire-fighters
:
Section 6. Accidental release measures
Environmental precautions
Personal precautions, protective equipment and emergency procedures
Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Approach release from upwind. Prevent entry into sewers,
water courses, basements or confined areas. Wash spillages into an effluent treatment
plant or proceed as follows. Contain and collect spillage with non-combustible,
absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in
container for disposal according to local regulations (see Section 13). Dispose of via a
licensed waste disposal contractor. Contaminated absorbent material may pose the
same hazard as the spilled product. Note: see Section 1 for emergency contact
information and Section 13 for waste disposal.
:
:No action shall be taken involving any personal risk or without suitable training.
Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilled material. Shut off all ignition sources.
No flares, smoking or flames in hazard area. Avoid breathing vapor or mist. Provide
adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put
on appropriate personal protective equipment.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air).
Large spill :
Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Dilute with water and mop up if water-soluble. Alternatively,
or if water-insoluble, absorb with an inert dry material and place in an appropriate waste
disposal container. Dispose of via a licensed waste disposal contractor.
Small spill :
Methods and materials for containment and cleaning up
For non-emergency
personnel
For emergency responders:If specialized clothing is required to deal with the spillage, take note of any information in
Section 8 on suitable and unsuitable materials. See also the information in “For non-
emergency personnel”.
Date of issue/Date of revision :1/8/2019 Date of previous issue :3/5/2016 Version:1.05 4/14

Core-Bond B73 R
Section 7. Handling and storage
Advice on general
occupational hygiene
Conditions for safe storage,
including any
incompatibilities
Eating, drinking and smoking should be prohibited in areas where this material is
handled, stored and processed. Workers should wash hands and face before eating,
drinking and smoking. Remove contaminated clothing and protective equipment before
entering eating areas. See also Section 8 for additional information on hygiene
measures.
Store in accordance with local regulations. Store in a segregated and approved area.
Store in original container protected from direct sunlight in a dry, cool and well-ventilated
area, away from incompatible materials (see Section 10) and food and drink. Store
locked up. Eliminate all ignition sources. Separate from oxidizing materials. Keep
container tightly closed and sealed until ready for use. Containers that have been
opened must be carefully resealed and kept upright to prevent leakage. Do not store in
unlabeled containers. Use appropriate containment to avoid environmental
contamination.
:
:
Protective measures Put on appropriate personal protective equipment (see Section 8). Avoid exposure –
obtain special instructions before use. Do not handle until all safety precautions have
been read and understood. Do not get in eyes or on skin or clothing. Do not breathe
vapor or mist. Do not ingest. Use only with adequate ventilation. Wear appropriate
respirator when ventilation is inadequate. Do not enter storage areas and confined
spaces unless adequately ventilated. Keep in the original container or an approved
alternative made from a compatible material, kept tightly closed when not in use. Store
and use away from heat, sparks, open flame or any other ignition source. Use
explosion-proof electrical (ventilating, lighting and material handling) equipment. Use
only non-sparking tools. Take precautionary measures against electrostatic discharges.
Empty containers retain product residue and can be hazardous. Do not reuse container.
:
Precautions for safe handling
styrene ACGIH TLV (United States, 3/2016).
TWA: 20 ppm 8 hours.
TWA: 85 mg/m 8 hours.
STEL: 40 ppm 15 minutes.
STEL: 170 mg/m 15 minutes.
OSHA PEL 1989 (United States, 3/1989).
TWA: 50 ppm 8 hours.
TWA: 215 mg/m 8 hours.
STEL: 100 ppm 15 minutes.
STEL: 425 mg/m 15 minutes.
OSHA PEL Z2 (United States, 2/2013).
TWA: 100 ppm 8 hours.
CEIL: 200 ppm
AMP: 600 ppm 5 minutes.
NIOSH REL (United States, 10/2016).
TWA: 50 ppm 10 hours.
TWA: 215 mg/m 10 hours.
STEL: 100 ppm 15 minutes.
STEL: 425 mg/m 15 minutes.
N,N-dimethylaniline ACGIH TLV (United States, 3/2016).
Absorbed through skin.
TWA: 5 ppm 8 hours.
TWA: 25 mg/m 8 hours.
STEL: 10 ppm 15 minutes.
STEL: 50 mg/m 15 minutes.
OSHA PEL 1989 (United States, 3/1989).
Absorbed through skin.
TWA: 5 ppm 8 hours.
Section 8. Exposure controls/personal protection
Ingredient name Exposure limits
Control parameters
Occupational exposure limits
Date of issue/Date of revision :1/8/2019 Date of previous issue :3/5/2016 Version:1.05 5/14

Core-Bond B73 R
Section 8. Exposure controls/personal protection
TWA: 25 mg/m 8 hours.
STEL: 10 ppm 15 minutes.
STEL: 50 mg/m 15 minutes.
NIOSH REL (United States, 10/2016).
Absorbed through skin.
TWA: 5 ppm 10 hours.
TWA: 25 mg/m 10 hours.
STEL: 10 ppm 15 minutes.
STEL: 50 mg/m 15 minutes.
OSHA PEL (United States, 6/2016).
Absorbed through skin.
TWA: 5 ppm 8 hours.
TWA: 25 mg/m 8 hours.
Hand protection
Based on the hazard and potential for exposure, select a respirator that meets the
appropriate standard or certification. Respirators must be used according to a
respiratory protection program to ensure proper fitting, training, and other important
aspects of use.
Chemical-resistant, impervious gloves complying with an approved standard should be
worn at all times when handling chemical products if a risk assessment indicates this is
necessary. Considering the parameters specified by the glove manufacturer, check
during use that the gloves are still retaining their protective properties. It should be
noted that the time to breakthrough for any glove material may be different for different
glove manufacturers. In the case of mixtures, consisting of several substances, the
protection time of the gloves cannot be accurately estimated.
Safety eyewear complying with an approved standard should be used when a risk
assessment indicates this is necessary to avoid exposure to liquid splashes, mists,
gases or dusts. If contact is possible, the following protection should be worn, unless
the assessment indicates a higher degree of protection: chemical splash goggles.
Eye/face protection
Respiratory protection :
:
:
Body protection Personal protective equipment for the body should be selected based on the task being
performed and the risks involved and should be approved by a specialist before
handling this product. When there is a risk of ignition from static electricity, wear anti-
static protective clothing. For the greatest protection from static discharges, clothing
should include anti-static overalls, boots and gloves.
:
Environmental exposure
controls
:Emissions from ventilation or work process equipment should be checked to ensure
they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process equipment
will be necessary to reduce emissions to acceptable levels.
Appropriate engineering
controls
:Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or
other engineering controls to keep worker exposure to airborne contaminants below any
recommended or statutory limits. The engineering controls also need to keep gas,
vapor or dust concentrations below any lower explosive limits. Use explosion-proof
ventilation equipment.
Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Wash contaminated clothing before reusing. Ensure that eyewash stations and safety
showers are close to the workstation location.
Hygiene measures :
Individual protection measures
Skin protection
Other skin protection :Appropriate footwear and any additional skin protection measures should be selected
based on the task being performed and the risks involved and should be approved by a
specialist before handling this product.
Date of issue/Date of revision :1/8/2019 Date of previous issue :3/5/2016 Version:1.05 6/14

Core-Bond B73 R
Section 9. Physical and chemical properties
Physical state
Melting point
Vapor pressure
Relative density
Vapor density
Solubility
Liquid. [Paste.]
Not available.
0.7 to 0.8
Not available.
Not available.
Not available.
SolventOdor
pH
White.Color
Evaporation rate Not available.
Auto-ignition temperature
Flash point
Not available.
Closed cup: 31 C (87.8 F)
Not available.
Not available.
Viscosity Kinematic (40 C (104 F)): >0.4 cm
2
/s (>40 cSt)
Not available.Odor threshold
Partition coefficient: n-
octanol/water
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Appearance
Boiling point :Not available.
Flammability (solid, gas):Not available.
Lower and upper explosive
(flammable) limits
:Not available.
Burning rate Not applicable.:
Burning time :Not applicable.
SADT Not available.:
Decomposition temperature:Not available.
Aerosol product
Solubility in water :Not available.
Section 10. Stability and reactivity
Hazardous decomposition
products
Conditions to avoid Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld,
braze, solder, drill, grind or expose containers to heat or sources of ignition.
Under normal conditions of storage and use, hazardous decomposition products should
not be produced.
The product is stable.Chemical stability
Reactive or incompatible with the following materials:
oxidizing materials
:
:
:
Incompatible materials :
Possibility of hazardous
reactions
:Under normal conditions of storage and use, hazardous reactions will not occur.
Reactivity :No specific test data related to reactivity available for this product or its ingredients.
Date of issue/Date of revision :1/8/2019 Date of previous issue :3/5/2016 Version:1.05 7/14

Core-Bond B73 R
Section 11. Toxicological information
Acute toxicity
styrene LC50 Inhalation Gas. Rat 2770 ppm 4 hours
LC50 Inhalation Vapor Rat 11800 mg/m 4 hours
LD50 Dermal Rat >2000 mg/kg –
LD50 Oral Rat 2650 mg/kg –
N,N-dimethylaniline LC50 Inhalation Vapor Rat >5.1 mg/l 4 hours
LD50 Dermal Rabbit 1700 mg/kg –
LD50 Oral Rat 1120 mg/kg –
Product/ingredient name Result Species Dose Exposure
Carcinogenicity
Not available.
Mutagenicity
Not available.
Teratogenicity
Not available.
Reproductive toxicity
Not available.
Irritation/Corrosion
styrene Eyes – Mild irritant Human – 50 parts per
million
–
Eyes – Moderate irritantRabbit – 24 hours 100
milligrams
–
Eyes – Severe irritantRabbit – 100
milligrams
–
Skin – Mild irritant Rabbit – 500
milligrams
–
Skin – Moderate irritantRabbit – 100 Percent-
Product/ingredient name Result Score Exposure Observation
Sensitization
Not available.
Species
Specific target organ toxicity (single exposure)
Specific target organ toxicity (repeated exposure)
styrene Category 3 Not applicable.Respiratory tract
irritation
Name Category
Name Category
styrene Category 1 Inhalation hearing organs
Aspiration hazard
Name Result
styrene ASPIRATION HAZARD – Category 1
Route of
exposure
Target organs
Route of
exposure
Target organs
Information on toxicological effects
Classification
styrene – 2B Reasonably anticipated to be a human carcinogen.
N,N-dimethylaniline – 3 –
Product/ingredient name NTPIARCOSHA
Date of issue/Date of revision :1/8/2019 Date of previous issue :3/5/2016 Version:1.05 8/14

Core-Bond B73 R
Section 11. Toxicological information
styrene Chronic NOAEL Dermal Rat 615 mg/kg –
Chronic NOAEL Inhalation
Gas.
Rat 20 ppm 8 hours
Product/ingredient name Result Species Dose Exposure
Information on the likely
routes of exposure
Inhalation :Harmful if inhaled. May cause respiratory irritation.
No known significant effects or critical hazards.:Ingestion
Skin contact :Causes skin irritation.
Causes serious eye irritation.:Eye contact
Causes damage to organs through prolonged or repeated exposure.General :
Suspected of causing cancer. Risk of cancer depends on duration and level of
exposure.
Carcinogenicity :
No known significant effects or critical hazards.Mutagenicity :
No known significant effects or critical hazards.Teratogenicity :
Developmental effects :No known significant effects or critical hazards.
Fertility effects :No known significant effects or critical hazards.
Symptoms related to the physical, chemical and toxicological characteristics
Skin contact
Ingestion
Inhalation Adverse symptoms may include the following:
respiratory tract irritation
coughing
No specific data.
Adverse symptoms may include the following:
irritation
redness
:
:
:
Eye contact :Adverse symptoms may include the following:
pain or irritation
watering
redness
Potential chronic health effects
Delayed and immediate effects and also chronic effects from short and long term exposure
Numerical measures of toxicity
Oral 7297.5 mg/kg
Inhalation (gases) 7286.7 ppm
Inhalation (vapors) 31.04 mg/l
Route ATE value
Acute toxicity estimates
:Not available.
Potential acute health effects
Potential immediate
effects
:Not available.
Short term exposure
Potential delayed effects:Not available.
Potential immediate
effects
:Not available.
Long term exposure
Potential delayed effects:Not available.
Date of issue/Date of revision :1/8/2019 Date of previous issue :3/5/2016 Version:1.05 9/14

Core-Bond B73 R
Section 12. Ecological information
LogPow BCF Potential
Bioaccumulative potential
Other adverse effects :No known significant effects or critical hazards.
Product/ingredient name
styrene 0.35 13.49 low
N,N-dimethylaniline 1.171 16 low
Product/ingredient name Aquatic half-life Photolysis Biodegradability
styrene – – Readily
Toxicity
styrene Acute EC50 1400 g/l Fresh water Algae – Pseudokirchneriella
subcapitata
72 hours
Acute EC50 33 mg/l Fresh water Algae – Pseudokirchneriella
subcapitata
96 hours
Acute EC50 4700 g/l Fresh water Daphnia – Daphnia magna 48 hours
Acute LC50 52 mg/l Marine water Crustaceans – Artemia salina48 hours
Acute LC50 4020 g/l Fresh water Fish – Pimephales promelas 96 hours
Chronic NOEC 1.01 mg/l Daphnia 21 days
N,N-dimethylaniline Acute EC50 5 mg/l Daphnia – Daphnia magna 48 hours
Acute IC50 340 mg/l Algae – Desmodesmus
subspicatus
96 hours
Acute LC50 65.6 mg/l Fish – Pimephales promelas 96 hours
Product/ingredient name SpeciesResult Exposure
Persistence and degradability
Soil/water partition
coefficient (KOC)
:Not available.
Mobility in soil
Section 13. Disposal considerations
The generation of waste should be avoided or minimized wherever possible. Disposal
of this product, solutions and any by-products should at all times comply with the
requirements of environmental protection and waste disposal legislation and any
regional local authority requirements. Dispose of surplus and non-recyclable products
via a licensed waste disposal contractor. Waste should not be disposed of untreated to
the sewer unless fully compliant with the requirements of all authorities with jurisdiction.
Waste packaging should be recycled. Incineration or landfill should only be considered
when recycling is not feasible. This material and its container must be disposed of in a
safe way. Care should be taken when handling emptied containers that have not been
cleaned or rinsed out. Empty containers or liners may retain some product residues.
Vapor from product residues may create a highly flammable or explosive atmosphere
inside the container. Do not cut, weld or grind used containers unless they have been
cleaned thoroughly internally. Avoid dispersal of spilled material and runoff and contact
with soil, waterways, drains and sewers.
:Disposal methods
Section 14. Transport information
Date of issue/Date of revision :1/8/2019 Date of previous issue :3/5/2016 Version:1.05 10/14

Core-Bond B73 R
Section 14. Transport information
Resin solution
3
III
RESIN
SOLUTION
3
III
Resin solution
UN1866
3
III
UN1866 UN1866
Reportable
quantity 3325.
9 lbs / 1509.9
kg [531.85 gal /
2013.3 L].
Package sizes
shipped in
quantities less
than the
product
reportable
quantity are
not subject to
the RQ
(reportable
quantity)
transportation
requirements.
Limited
quantity Yes.
Packaging
instruction
Exceptions:
150. Non-bulk:
173. Bulk: 242.
Quantity
limitation
Passenger
aircraft/rail: 60
L. Cargo
aircraft: 220 L.
Special
provisions B1,
B52, IB3, T2,
TP1
Emergency
schedules F-E,
_S-E_
Special
provisions
223, 955
Quantity
limitation
Passenger and
Cargo Aircraft:
60 L.
Packaging
instructions:
355. Cargo
Aircraft Only:
220 L.
Packaging
instructions:
366. Limited
Quantities –
Passenger
Aircraft: 10 L.
Packaging
instructions:
Y344.
Special
provisions A3
DOT
Classification
IMDG IATA
UN number
UN proper
shipping name
Transport
hazard class(es)
Packing group
Additional
information
Environmental
hazards
Special precautions for user
No. No. No.
Transport within user s premises: always transport in closed containers that are
upright and secure. Ensure that persons transporting the product know what to do in the
event of an accident or spillage.
:
TDG
Classification
UN1866
RESIN
SOLUTION
3
III
No.
Product
classified as
per the
following
sections of the
Transportation
of Dangerous
Goods
Regulations: 2.
18-2.19 (Class
3).
Explosive
Limit and
Limited
Quantity Index
5
Passenger
Carrying
Road or Rail
Index 60
ADR/RID
UN1866
RESIN
SOLUTION
3
III
No.
Hazard
identification
number 30
Limited
quantity 5 L
Special
provisions
640E
Tunnel code
(D/E)
Mexico
Classification
UN1866
RESINA,
SOLUCIONES
DE
3
III
No.
Special
provisions 223
Date of issue/Date of revision :1/8/2019 Date of previous issue :3/5/2016 Version:1.05 11/14

Core-Bond B73 R
Section 14. Transport information
Transport in bulk according
to Annex II of MARPOL and
the IBC Code
:Not available.
Section 15. Regulatory information
U.S. Federal regulations
The following components are listed: STYRENE; PHENYLETHYLENE; FIBROUS
GLASS
Massachusetts
:
:
SARA 313
Product name CAS number %
SARA 313 notifications must not be detached from the SDS and any copying and redistribution of the SDS shall include
copying and redistribution of the notice attached to copies of the SDS subsequently redistributed.
styrene 100-42-5 30.067
styrene 100-42-5 30.067
Form R – Reporting
requirements
Supplier notification
Clean Air Act Section 112
(b) Hazardous Air
Pollutants (HAPs)
:Listed
Clean Air Act Section 602
Class I Substances
:Not listed
Clean Air Act Section 602
Class II Substances
:Not listed
DEA List I Chemicals
(Precursor Chemicals)
:Not listed
DEA List II Chemicals
(Essential Chemicals)
:Not listed
State regulations
TSCA 8(a) PAIR: N,N-dimethylaniline
TSCA 8(a) CDR Exempt/Partial exemption: Not determined
SARA 302/304
SARA 304 RQ :21801002628.1 lbs / 9897655193.2 kg [3486245176.5 gal / 13196873590.9 L]
aniline 0.
00000417 –
0.0000417
Yes.1000 117.6 5000 587.9
Composition/information on ingredients
Name % EHS(lbs) (lbs)(gallons) (gallons)
SARA 302 TPQ SARA 304 RQ
SARA 311/312
Classification :Fire hazard
Immediate (acute) health hazard
Delayed (chronic) health hazard
styrene 30.067 Yes. No. No. Yes. Yes.
N,N-dimethylaniline 0.1323 Yes. No. No. Yes. Yes.
Name % Fire
hazard
Sudden
release of
pressure
Reactive Immediate
(acute)
health
hazard
Delayed
(chronic)
health
hazard
Composition/information on ingredients
Date of issue/Date of revision :1/8/2019 Date of previous issue :3/5/2016 Version:1.05 12/14

Core-Bond B73 R
Section 15. Regulatory information
WARNING: This product contains a chemical known to the State of California to cause cancer. WARNING: This product
contains less than 1% of a chemical known to the State of California to cause birth defects or other reproductive harm.
styrene Yes. No. – –
ethanediol No. Yes. – –
aniline Yes. No. Yes. –
Ingredient name Cancer Reproductive No significant risk
level
Maximum
acceptable dosage
level
California Prop. 65
New York :The following components are listed: Styrene; n,n-Diethylaniline
New Jersey :The following components are listed: STYRENE MONOMER; BENZENE, ETHENYL-;
DIMETHYLANILINE; BENZENAMINE, N,N-DIMETHYL-
Pennsylvania :The following components are listed: BENZENE, ETHENYL-; BENZENAMINE, N,N-
DIMETHYL-
International regulations
Montreal Protocol (Annexes A, B, C, E)
Not listed.
Stockholm Convention on Persistent Organic Pollutants
Not listed.
Rotterdam Convention on Prior Informed Consent (PIC)
Not listed.
Chemical Weapon Convention List Schedules I, II & III Chemicals
Not listed.
UNECE Aarhus Protocol on POPs and Heavy Metals
Not listed.
International lists
National inventoryNot determined
Section 16. Other information
Hazardous Material Information System (U.S.A.)
3
3
0
0
3
2
*
National Fire Protection Association (U.S.A.)
Health
Special
Instability/Reactivity
Flammability
Health
Flammability
Physical hazards
Caution: HMIS ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4
representing significant hazards or risks. Although HMIS ratings and the associated label are not required on
SDSs or products leaving a facility under 29 CFR 1910.1200, the preparer may choose to provide them. HMIS
ratings are to be used with a fully implemented HMIS program. HMIS is a registered trademark and service
mark of the American Coatings Association, Inc.
The customer is responsible for determining the PPE code for this material. For more information on HMIS
Personal Protective Equipment (PPE) codes, consult the HMIS Implementation Manual.
Date of issue/Date of revision :1/8/2019 Date of previous issue :3/5/2016 Version:1.05 13/14

Core-Bond B73 R
Section 16. Other information
1/8/2019
History
Date of printing
Date of issue/Date of
revision
Version
To the best of our knowledge, the information contained herein is accurate. However, neither the above-named
supplier, nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the
information contained herein.
Final determination of suitability of any material is the sole responsibility of the user. All materials may present
unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot
guarantee that these are the only hazards that exist.
Notice to reader
Date of previous issue
:
:
:
:
Indicates information that has changed from previously issued version.
References :Not available.
Key to abbreviations :ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships, 1973
as modified by the Protocol of 1978. (“Marpol” = marine pollution)
UN = United Nations
1/8/2019
3/5/2016
1.05
Reprinted with permission from NFPA 704-2001, Identification of the Hazards of Materials for Emergency
Response Copyright 1997, National Fire Protection Association, Quincy, MA 02269. This reprinted material is
not the complete and official position of the National Fire Protection Association, on the referenced subject
which is represented only by the standard in its entirety.
Copyright 2001, National Fire Protection Association, Quincy, MA 02269. This warning system is intended to
be interpreted and applied only by properly trained individuals to identify fire, health and reactivity hazards of
chemicals. The user is referred to certain limited number of chemicals with recommended classifications in
NFPA 49 and NFPA 325, which would be used as a guideline only. Whether the chemicals are classified by NFPA
or not, anyone using the 704 systems to classify chemicals does so at their own risk.
Date of issue/Date of revision :1/8/2019 Date of previous issue :3/5/2016 Version:1.05 14/14

23B73RD_SDS.pdf