ADHESIVES | Revchem Composites

23577359_SDS.pdf

by | Sep 27, 2025

Safety Data Sheet
according to OSHA 1910.1200 Hazard Communication Standard

Sikaflex -292i

Revision Date 01/23/2024

Print Date 01/23/2024

1 / 11

SECTION 1. IDENTIFICATION
Product name : Sikaflex -292i

Company name : Sika Corporation

201 Polito Avenue
Lyndhurst, NJ 07071
USA
www.sikausa.com

Telephone : (201) 933-8800

Telefax : (201) 804-1076

E-mail address : ehs@sika-corp.com

Emergency telephone : CHEMTREC: 800-424-9300
INTERNATIONAL: +1-703-527-3887

Recommended use of the
chemical and restrictions on
use
: For further information, refer to product data sheet.

SECTION 2. HAZARDS IDENTIFICATION
GHS classification in accordance with the OSHA Hazard Communication Standard (29 CFR
1910.1200)
Skin sensitization

: Category 1
Reproductive toxicity

: Category 2
GHS label elements
Hazard pictograms

:

Signal Word

: Warning

Hazard Statements

: H317 May cause an allergic skin reaction.
H361 Suspected of damaging fertility or the unborn child.

Precautionary Statements

: P101 If medical advice is needed, have product container or
label at hand.
P102 Keep out of reach of children.
Prevention:
P201 Obtain special instructions before use.

Safety Data Sheet
according to OSHA 1910.1200 Hazard Communication Standard

Sikaflex -292i

Revision Date 01/23/2024

Print Date 01/23/2024

2 / 11

P202 Do not handle until all safety precautions have been read
and understood.
P261 Avoid breathing mist or vapors.
P272 Contaminated work clothing must not be allowed out of
the workplace.
P280 Wear protective gloves/ protective clothing/ eye protection/
face protection.
Response:
P302 + P352 IF ON SKIN: Wash with plenty of soap and water.
P308 + P313 IF exposed or concerned: Get medical advice/
attention.
P333 + P313 If skin irritation or rash occurs: Get medical advice/
attention.
P362 + P364 Take off contaminated clothing and wash it before
reuse.
Storage:
P405 Store locked up.
Disposal:
P501 Dispose of contents/ container to an approved waste dis-
posal plant.

Additional Labeling
There are no ingredients with unknown acute toxicity used in a mixture at a concentration >= 1%.
Other hazards
None known.
SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS
Mixtures
Components
Chemical name CAS-No. Classification Concentra-
tion (% w/w)
Aliphatic polyisocyanate 28182-81-2 Acute Tox. 4; H332
Skin Sens. 1; H317
STOT SE 3; H335
>= 0.1 – < 1 Reaction product of Hexamethylene diisocyanate, oligomers with Mer- captopropyltrimethoxysilane Not Assigned Skin Sens. 1A; H317 >= 0.1 – < 1 Pentamethyl piperidylsebacate 41556-26-7 Skin Sens. 1A; H317 Repr. 2; H361 >= 0.1 – < 1 Actual concentration is withheld as a trade secret SECTION 4. FIRST AID MEASURES General advice : Move out of dangerous area. Safety Data Sheet according to OSHA 1910.1200 Hazard Communication Standard Sikaflex -292i Revision Date 01/23/2024 Print Date 01/23/2024 3 / 11 Consult a physician. Show this material safety data sheet to the doctor in attend- ance. If inhaled : Move to fresh air. Consult a physician after significant exposure. In case of skin contact : Take off contaminated clothing and shoes immediately. Wash off with soap and plenty of water. If symptoms persist, call a physician. In case of eye contact : Remove contact lenses. Keep eye wide open while rinsing. If eye irritation persists, consult a specialist. If swallowed : Clean mouth with water and drink afterwards plenty of water. Do not induce vomiting without medical advice. Do not give milk or alcoholic beverages. Never give anything by mouth to an unconscious person. Obtain medical attention. Most important symptoms and effects, both acute and delayed : sensitizing effects Allergic reactions May cause an allergic skin reaction. Suspected of damaging fertility or the unborn child. Notes to physician : Treat symptomatically. SECTION 5. FIRE-FIGHTING MEASURES Suitable extinguishing media : Use extinguishing measures that are appropriate to local cir- cumstances and the surrounding environment. Further information : Collect contaminated fire extinguishing water separately. This must not be discharged into drains. Fire residues and contaminated fire extinguishing water must be disposed of in accordance with local regulations. Special protective equipment for fire-fighters : In the event of fire, wear self-contained breathing apparatus. SECTION 6. ACCIDENTAL RELEASE MEASURES Personal precautions, protec- tive equipment and emer- gency procedures : Use personal protective equipment. Deny access to unprotected persons. Environmental precautions : Do not flush into surface water or sanitary sewer system. If the product contaminates rivers and lakes or drains inform respective authorities. Safety Data Sheet according to OSHA 1910.1200 Hazard Communication Standard Sikaflex -292i Revision Date 01/23/2024 Print Date 01/23/2024 4 / 11 Local authorities should be advised if significant spillages cannot be contained. Methods and materials for containment and cleaning up : Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust). Keep in suitable, closed containers for disposal. SECTION 7. HANDLING AND STORAGE Advice on protection against fire and explosion : Normal measures for preventive fire protection. Advice on safe handling : Avoid exceeding the given occupational exposure limits (see section 8). Do not get in eyes, on skin, or on clothing. For personal protection see section 8. Persons with a history of skin sensitization problems or asth- ma, allergies, chronic or recurrent respiratory disease should not be employed in any process in which this mixture is being used. Smoking, eating and drinking should be prohibited in the ap- plication area. Follow standard hygiene measures when handling chemical products. Conditions for safe storage : Store in original container. Keep container tightly closed in a dry and well-ventilated place. Observe label precautions. Store in accordance with local regulations. SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION Ingredients with workplace control parameters Contains no substances with occupational exposure limit values. Engineering measures : Use of adequate ventilation should be sufficient to control worker exposure to airborne contaminants. If the use of this product generates dust, fumes, gas, vapor or mist, use pro- cess enclosures, local exhaust ventilation or other engineer- ing controls to keep worker exposure below any recommend- ed or statutory limits. Personal protective equipment Respiratory protection : Use a properly fitted NIOSH approved air-purifying or air-fed respirator complying with an approved standard if a risk as- sessment indicates this is necessary. The filter class for the respirator must be suitable for the max- imum expected contaminant concentration Safety Data Sheet according to OSHA 1910.1200 Hazard Communication Standard Sikaflex -292i Revision Date 01/23/2024 Print Date 01/23/2024 5 / 11 (gas/vapor/aerosol/particulates) that may arise when han- dling the product. If this concentration is exceeded, self- contained breathing apparatus must be used. Hand protection : Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is nec- essary. Eye protection : Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary. Skin and body protection : Choose body protection in relation to its type, to the concen- tration and amount of dangerous substances, and to the spe- cific work-place. Hygiene measures : Avoid contact with skin, eyes and clothing. Wash hands before breaks and immediately after handling the product. Remove contaminated clothing and protective equipment before entering eating areas. Wash thoroughly after handling. SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance : paste Color : various Odor : odorless Odor Threshold : No data available pH : Not applicable substance/mixture is non-soluble (in water) Melting point/range / Freezing point : No data available Boiling point/boiling range : No data available Flash point : > 214 F / 101 C
(Method: closed cup)

Evaporation rate : No data available

Flammability (solid, gas)

: No data available

Upper explosion limit / Upper
flammability limit

: No data available

Lower explosion limit / Lower
flammability limit
: No data available

Safety Data Sheet
according to OSHA 1910.1200 Hazard Communication Standard

Sikaflex -292i

Revision Date 01/23/2024

Print Date 01/23/2024

6 / 11

Vapor pressure : 0.01 hpa

Relative vapor density : No data available

Density : ca. 1.3 g/cm3 (68 F / 20 C)

Solubility(ies)
Water solubility : insoluble

Solubility in other solvents : No data available

Partition coefficient: n-
octanol/water
: No data available

Autoignition temperature : No data available

Decomposition temperature : No data available

Viscosity
Viscosity, dynamic : Not applicable

Viscosity, kinematic : Not applicable

Explosive properties : No data available

Oxidizing properties : No data available

Volatile organic compounds
(VOC) content
: 23 g/l

SECTION 10. STABILITY AND REACTIVITY
Reactivity : No dangerous reaction known under conditions of normal use.

Chemical stability : The product is chemically stable.

Possibility of hazardous reac-
tions

: Stable under recommended storage conditions.

Conditions to avoid : No data available

Incompatible materials : No data available

Hazardous decomposition
products

: No decomposition if stored and applied as directed.

SECTION 11. TOXICOLOGICAL INFORMATION
Acute toxicity
Not classified due to lack of data.

Safety Data Sheet
according to OSHA 1910.1200 Hazard Communication Standard

Sikaflex -292i

Revision Date 01/23/2024

Print Date 01/23/2024

7 / 11

Components:
Aliphatic polyisocyanate:
Acute oral toxicity : LD50 Oral (Rat): > 2,500 mg/kg

Acute inhalation toxicity : LC50: 1.5 mg/l
Exposure time: 4 h
Test atmosphere: dust/mist
Method: Expert judgment

Acute dermal toxicity : LD50 Dermal (Rat): > 2,000 mg/kg

Skin corrosion/irritation
Not classified due to lack of data.
Serious eye damage/eye irritation
Not classified due to lack of data.
Respiratory or skin sensitization
Skin sensitization
May cause an allergic skin reaction.
Respiratory sensitization
Not classified due to lack of data.
Germ cell mutagenicity
Not classified due to lack of data.
Carcinogenicity
Not classified due to lack of data.
IARC Group 2B: Possibly carcinogenic to humans
Titanium dioxide (> 10 m) 13463-67-7

OSHA Not applicable

NTP Not applicable

Reproductive toxicity
Suspected of damaging fertility or the unborn child.
STOT-single exposure
Not classified due to lack of data.
STOT-repeated exposure
Not classified due to lack of data.
Once sensitized, a severe allergic reaction may occur when subsequently exposed to very low levels.
Aspiration toxicity
Not classified due to lack of data.

Safety Data Sheet
according to OSHA 1910.1200 Hazard Communication Standard

Sikaflex -292i

Revision Date 01/23/2024

Print Date 01/23/2024

8 / 11

Further information
Product:
Remarks : Titanium dioxide (13463-67-7)
In lifetime inhalation studies of rats, airborne respirable-size
titanium dioxide particles have shown to cause an increase in
lung tumors at concentrations associated with substantial
particle lung burdens and consequential pulmonary overload
and inflammation. The potential for these adverse health ef-
fects appears to be closely related to the particle size and the
amount of the exposed surface area that comes into contact
with the lung. However, tests with other laboratory animals
such as mice and hamsters, indicate that rats are significantly
more susceptible to the pulmonary overload and inflammation
that causes lung cancer. Epidemiological studies do not sug-
gest an increased risk of cancer in humans from occupational
exposure to titanium dioxide. Titanium dioxide has been char-
acterized by IARC as possibly carcinogenic to humans (Group
2B) through inhalation (not ingestion). It has not been charac-
terized as a potential carcinogen by either NTP or OSHA.

SECTION 12. ECOLOGICAL INFORMATION
Ecotoxicity
Components:
Reaction product of Hexamethylene diisocyanate, oligomers with Mercaptopropyltrimethox-
ysilane:
Toxicity to fish : LC50 (Brachydanio rerio (zebrafish)): > 100 mg/l
Exposure time: 96 h
Method: OECD Test Guideline 203

Toxicity to daphnia and other
aquatic invertebrates
: EC50 (Daphnia magna (Water flea)): > 100 mg/l
Exposure time: 48 h
Method: OECD Test Guideline 202

Toxicity to algae/aquatic
plants
: EC50 (Pseudokirchneriella subcapitata (algae)): > 100 mg/l
Exposure time: 72 h
Method: OECD Test Guideline 201

Persistence and degradability
No data available
Bioaccumulative potential
No data available
Mobility in soil
No data available

Safety Data Sheet
according to OSHA 1910.1200 Hazard Communication Standard

Sikaflex -292i

Revision Date 01/23/2024

Print Date 01/23/2024

9 / 11

Other adverse effects
Product:
Additional ecological infor-
mation
: Do not empty into drains; dispose of this material and its con-
tainer in a safe way.
Avoid dispersal of spilled material and runoff and contact with
soil, waterways, drains and sewers.

SECTION 13. DISPOSAL CONSIDERATIONS
Disposal methods
Waste from residues : Disposal of this product, solutions and any by-products should
at all times comply with the requirements of environmental
protection and waste disposal legislation and any regional
local authority requirements.

Contaminated packaging : Empty containers should be taken to an approved waste han-
dling site for recycling or disposal.

SECTION 14. TRANSPORT INFORMATION
International Regulations
IATA-DGR
Not regulated as a dangerous good
IMDG-Code
Not regulated as a dangerous good
Domestic regulation
49 CFR
Not regulated as a dangerous good
SECTION 15. REGULATORY INFORMATION
TSCA list : All chemical substances in this product are either listed as ac-
tive on the TSCA Inventory or are in compliance with a TSCA
Inventory exemption.

The following substance(s) is/are subject to a Significant New Use Rule:
Polyoxypropylenedialdimine 613246-75-6 See 40 CFR 721.10408; Final
Rule
m-tolylidene diisocyanate 26471-62-5 See 40 CFR 721.10789; Proposed
Rule

No substances are subject to TSCA 12(b) export notification requirements.

Safety Data Sheet
according to OSHA 1910.1200 Hazard Communication Standard

Sikaflex -292i

Revision Date 01/23/2024

Print Date 01/23/2024

10 / 11

CERCLA Reportable Quantity
Listed substances in the product are at low enough levels to not be expected to exceed the RQ
SARA 304 Extremely Hazardous Substances Reportable Quantity
Listed substances in the product are at low enough levels to not be expected to exceed the RQ
SARA 302 Extremely Hazardous Substances Threshold Planning Quantity
This material does not contain any components with a section 302 EHS TPQ.
SARA 311/312 Hazards

: Respiratory or skin sensitization
Reproductive toxicity

SARA 313

: This material does not contain any chemical components with
known CAS numbers that exceed the threshold (De Minimis)
reporting levels established by SARA Title III, Section 313.

Clean Air Act
This product does not contain any hazardous air pollutants (HAP), as defined by the U.S. Clean Air
Act Section 112 (40 CFR 61).
California Prop. 65
WARNING: This product can expose you to chemicals including Titanium dioxide, which is known to
the State of California to cause cancer, and 1,2-Benzenedicarboxylic acid, di-C9-11-branched alkyl
esters, C10-rich , which is known to the State of California to cause birth defects or other reproductive
harm. For more information go to www.P65Warnings.ca.gov.

SECTION 16. OTHER INFORMATION
Full text of other abbreviations

Notes to Reader
The information contained in this Safety Data Sheet applies only to the actual Sika Corporation (“Sika”) product identified and described herein. This information is not intended to address, nor does it address the use or application of the identified Sika product in combination with any other
material, product or process. All of the information set forth herein is based on technical data re-
garding the identified product that Sika believes to be reliable as of the date hereof. Prior to each
use of any Sika product, the user must always read and follow the warnings and instructions on
the product’s current Product Data Sheet, product label and Safety Data Sheet for each Sika
product, which are available at web site and/or telephone number listed in Section 1 of this SDS.

SIKA MAKES NO WARRANTIES EXPRESS OR IMPLIED AND ASSUMES NO LIABILITY
ARISING FROM THIS INFORMATION OR ITS USE. SIKA SHALL NOT BE LIABLE UNDER
ANY LEGAL THEORY FOR SPECIAL OR CONSEQUENTIAL DAMAGES AND SHALL NOT BE
RESPONSIBLE FOR THE USE OF THIS PRODUCT IN A MANNER TO INFRINGE ON ANY
PATENT OR ANY OTHER INTELLECTUAL PROPERTY RIGHTS HELD BY OTHERS.

All sales of Sika products are subject to its current terms and conditions of sale available at
www.sikausa.com or 201-933-8800.

Safety Data Sheet
according to OSHA 1910.1200 Hazard Communication Standard

Sikaflex -292i

Revision Date 01/23/2024

Print Date 01/23/2024

11 / 11

Revision Date 01/23/2024

000000607756
US / Z8

23533229_SDS.pdf

by | Sep 27, 2025

233M97957_SDS.pdf

by | Sep 27, 2025

233M97956_SDS.pdf

by | Sep 27, 2025

233M96272_SDS.pdf

by | Sep 27, 2025

233M65263_SDS.pdf

by | Sep 27, 2025

233M49000_SDS.pdf

by | Sep 27, 2025

233M49054_SDS.pdf

by | Sep 27, 2025

233M43672_SDS.pdf

by | Sep 27, 2025

3M Scotch-Weld Epoxy Adhesive DP460NS Off-White
____________________________________________________________________
Page: 1 of 2
Safety Data Sheet
Copyright,2022, 3M Canada Company. All rights reserved. Copying and/or downloading of this information for
the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes
unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise
distributed with the intention of earning a profit thereon.
Document group:09-1018-2Version number:17.00Issue Date:2022/10/26Supercedes Date:2021/04/15
SECTION 1: Identification
1.1. Product identifier
3M Scotch-Weld Epoxy Adhesive DP460NS Off-White
Product Identification Numbers
62-2792-1430-8

62-2792-1431-6

62-2792-1435-7

62-2792-1436-5

62-2792-2030-5

62-2792-3530-3

62-2792-3830-7

HB-0044-6833-4

HB-0045-2688-3

HB-0046-2619-6
1.2. Recommended use and restrictions on use
Recommended use
Structural adhesive
1.3. Supplier s details
Company:3M Canada CompanyDivision:Industrial Adhesives and Tapes DivisionAddress:1840 Oxford Street East, Post Office Box 5757, London, Ontario N6A 4T1Telephone:(800) 364-3577E Mail:
1.4. Emergency telephone number
Medical Emergency Telephone:1-800-3M HELPS / 1-800-364-3577; Transportation Emergency Telephone (CANUTEC):
(613) 996-6666
This product is a kit or a multipart product which consists of multiple, independently packaged components. A Safety
Data Sheet (SDS) or Article Information Sheet (AIS) for each of these components is included. Please do not separate
the component documents from this cover page. The document numbers for components of this product are:
09-0979-6, 22-0536-7
Transport in accordance with applicable regulations.
The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. The manufacturer MAKES
NO WARRANTIES, EXPRESS OR IMPLIED, STATUTORY OR OTHERWISE, INCLUDING, BUT NOT LIMITED TO,
ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF A COURSE OF PERFORMANCE,

3M Scotch-Weld Epoxy Adhesive DP460NS Off-White
____________________________________________________________________
Page: 2 of 2
COURSE OF DEALING, CUSTOM OR USAGE OF TRADE. User is responsible for determining whether the product is fit
for a particular purpose and suitable for user’s method of use or application. Given the variety of factors that can affect the
use and application of a product, some of which are uniquely within the user’s knowledge and control, it is essential that the
user evaluate the product to determine whether it is fit for a particular purpose and suitable for user’s method of use or
application.
3M Canada SDSs are available at www.3M.ca

3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE DP-460 NS (Part A)
__________________________________________________________________________________________
Page: 1 of 10
Safety Data Sheet
Copyright,2024, 3M Canada Company. All rights reserved. Copying and/or downloading of this information for
the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes
unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed
with the intention of earning a profit thereon.
Document group:22-0536-7 Version number:13.01Issue Date:2024/02/05Supercedes Date:2022/10/26
This Safety Data Sheet has been prepared in accordance with the Canadian Hazardous Products Regulations.
SECTION 1: Identification
1.1. Product identifier
3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE DP-460 NS (Part A)
Product Identification Numbers
LA-D100-2245-5 LA-D100-0280-6 LA-D100-0280-7 LA-D100-0280-8 LA-D100-0309-4
1.2. Recommended use and restrictions on use
Intended Use
Structural adhesive
Restrictions on use
Not applicable
1.3. Supplier s details
Company:3M Canada CompanyDivision:Industrial Adhesives and Tapes DivisionAddress:1840 Oxford Street East, Post Office Box 5757, London, Ontario N6A 4T1Telephone:(800) 364-3577Website:www.3M.ca
1.4. Emergency telephone number
Medical Emergency Telephone:1-800-3M HELPS / 1-800-364-3577; Transportation Emergency Telephone (CANUTEC):
(613) 996-6666
SECTION 2: Hazard identification
2.1. Classification of the substance or mixture
Serious Eye Damage/Irritation: Category 1.
Skin Corrosion/Irritation: Category 1B.
Skin Sensitizer: Category 1.
2.2. Label elements
Signal word
Danger

3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE DP-460 NS (Part A)
__________________________________________________________________________________________
Page: 2 of 10
Symbols
Corrosion | Exclamation mark |
Pictograms
Hazard statements
Causes severe skin burns and eye damage. May cause an allergic skin reaction.
Precautionary statements
Prevention:
Do not breathe dust/fume/gas/mist/vapours/spray. Wear protective gloves, protective clothing, and eye/face protection. Wash
exposed skin thoroughly after handling. Contaminated work clothing must not be allowed out of the workplace.
Response:
IF INHALED: Remove person to fresh air and keep comfortable for breathing. IF ON SKIN (or hair): Take off immediately
all contaminated clothing. Rinse skin with water or shower. IF IN EYES: Rinse cautiously with water for several minutes.
Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTRE or
doctor/physician. If skin irritation or rash occurs: Get medical advice/attention. Take off contaminated clothing and wash it
before reuse. IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.
Storage:
Store locked up.
Disposal:
Dispose of contents/container in accordance with applicable local/regional/national/international regulations.
2.3. Other hazards
May cause chemical gastrointestinal burns.
SECTION 3: Composition/information on ingredients
This material is a mixture.
IngredientC.A.S. No.% by WtCommon NameModified Epoxy ResinTrade Secret 40 – 70Not Applicable4,7,10-Trioxatridecane-1,13-
Diamine
4246-51-9 30 – 60 Trade Secret *1-Propanamine, 3,3′-[oxybis(2,1-
ethanediyloxy)]bis-
2,4,6-tris((Dimethylamino)-
Methyl)Phenol
90-72-2 1 – 5 Trade Secret *Phenol, 2,4,6-tris[(dimethylamino)methyl]-Amorphous Silica67762-90-7 1 – 5Siloxanes and Silicones, di-Me, reaction
products with silica
Modified Epoxy Resin is a non-hazardous Trade Secret material according to WHMIS criteria.
*The actual concentration of this ingredient has been withheld as a trade secret.
SECTION 4: First aid measures

3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE DP-460 NS (Part A)
__________________________________________________________________________________________
Page: 3 of 10
4.1. Description of first aid measures
Inhalation:
Remove person to fresh air. If you feel unwell, get medical attention.
Skin Contact:
Immediately flush with large amounts of water for at least 15 minutes. Remove contaminated clothing. Get immediate medical
attention. Wash clothing before reuse.
Eye Contact:
Immediately flush with large amounts of water for at least 15 minutes. Remove contact lenses if easy to do. Continue rinsing.
Immediately get medical attention.
If Swallowed:
Rinse mouth. Do not induce vomiting. Get immediate medical attention.
4.2. Most important symptoms and effects, both acute and delayed
Skin burns (localized redness, swelling, itching, intense pain, blistering, and tissue destruction). Allergic skin reaction (redness, swelling,
blistering, and itching). Serious damage to the eyes (corneal cloudiness, severe pain, tearing, ulcerations, and significantly impaired or loss
of vision).
4.3. Indication of any immediate medical attention and special treatment required
Not applicable
SECTION 5: Fire-fighting measures
5.1. Suitable extinguishing media
In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish.
5.2. Special hazards arising from the substance or mixture
None inherent in this product.
Hazardous Decomposition or By-Products
Substance ConditionAldehydesDuring CombustionCarbon monoxideDuring CombustionCarbon dioxideDuring CombustionHydrogen ChlorideDuring CombustionOxides of NitrogenDuring Combustion

5.3. Special protective actions for fire-fighters
Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus (SCBA). Wear full protective
clothing, including helmet, self-contained, positive pressure or pressure demand breathing apparatus, bunker coat and pants,
bands around arms, waist and legs, face mask, and protective covering for exposed areas of the head.
SECTION 6: Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
Evacuate area. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation
to disperse or exhaust vapours, in accordance with good industrial hygiene practice. Refer to other sections of this SDS for
information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment.
6.2. Environmental precautions
Avoid release to the environment. For larger spills, cover drains and build dikes to prevent entry into sewer systems or
bodies of water.

3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE DP-460 NS (Part A)
__________________________________________________________________________________________
Page: 4 of 10
6.3. Methods and material for containment and cleaning up
Contain spill. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially
available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent
material does not remove a physical, health, or environmental hazard. Collect as much of the spilled material as possible.
Place in a closed container approved for transportation by appropriate authorities. Clean up residue with an appropriate
solvent selected by a qualified and authorized person. Ventilate the area with fresh air. Read and follow safety precautions
on the solvent label and SDS. Seal the container. Dispose of collected material as soon as possible in accordance with
applicable local/regional/national/international regulations.
SECTION 7: Handling and storage
7.1. Precautions for safe handling
For industrial or professional use only. Not for consumer sale or use. Do not breathe dust/fume/gas/mist/vapours/spray.
Do not get in eyes, on skin, or on clothing. Do not eat, drink or smoke when using this product. Wash thoroughly after
handling. Contaminated work clothing should not be allowed out of the workplace. Avoid release to the environment.
Wash contaminated clothing before reuse. Avoid contact with oxidizing agents (eg. chlorine, chromic acid etc.)
7.2. Conditions for safe storage including any incompatibilities
Store away from acids. Store away from strong bases. Store away from oxidizing agents. Store away from amines.
SECTION 8: Exposure controls/personal protection
8.1. Control parameters
Occupational exposure limits
No occupational exposure limit values exist for any of the components listed in Section 3 of this SDS.
8.2. Exposure controls
8.2.1. Engineering controls
Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below relevant Exposure
Limits and/or control dust/fume/gas/mist/vapours/spray. If ventilation is not adequate, use respiratory protection equipment.
8.2.2. Personal protective equipment (PPE)
Eye/face protection
Select and use eye/face protection to prevent contact based on the results of an exposure assessment. The following eye/face
protection(s) are recommended:
Full Face Shield
Indirect Vented Goggles
Skin/hand protection
Select and use gloves and/or protective clothing approved to relevant local standards to prevent skin contact based on the
results of an exposure assessment. Selection should be based on use factors such as exposure levels, concentration of the
substance or mixture, frequency and duration, physical challenges such as temperature extremes, and other use conditions.
Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible gloves/protective
clothing.
Gloves made from the following material(s) are recommended: Butyl Rubber
Nitrile Rubber
Polymer laminate
If this product is used in a manner that presents a higher potential for exposure (eg. spraying, high splash potential etc.), then
use of protective coveralls may be necessary. Select and use body protection to prevent contact based on the results of an
exposure assessment. The following protective clothing material(s) are recommended: Apron Butyl rubber

3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE DP-460 NS (Part A)
__________________________________________________________________________________________
Page: 5 of 10
Apron Nitrile
Apron – polymer laminate
Respiratory protection
An exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part
of a full respiratory protection program. Based on the results of the exposure assessment, select from the following
respirator type(s) to reduce inhalation exposure:
Half facepiece or full facepiece air-purifying respirator suitable for organic vapours and particulates
For questions about suitability for a specific application, consult with your respirator manufacturer.
SECTION 9: Physical and chemical properties
9.1. Information on basic physical and chemical properties
Physical stateLiquid Specific Physical Form: viscous liquidColourAmberOdourVery Mild Odour, Pungent OdourOdour thresholdNo Data AvailablepHNot ApplicableMelting point/Freezing pointNot ApplicableBoiling point>=171 CFlash Point171.1 C [ Test Method:Closed Cup]Evaporation rateNo Data AvailableFlammability (solid, gas)Not ApplicableFlammable Limits(LEL)No Data AvailableFlammable Limits(UEL)No Data AvailableVapour Pressure<=400 Pa [@ 20 C ]Vapour Density and/or Relative Vapour Density3.72 [Ref Std:AIR=1]Density1.09 g/mlRelative density1.09 [Ref Std:WATER=1]Water solubilitySlight (less than 10%)Solubility- non-waterNo Data AvailablePartition coefficient: n-octanol/ waterNo Data AvailableAutoignition temperatureNo Data AvailableDecomposition temperatureNo Data AvailableViscosity/Kinematic Viscosity8,000 - 16,000 mPa-s [@ 23 C ] [Test Method:Brookfield]Volatile Organic CompoundsNo Data AvailablePercent volatileNo Data AvailableVOC Less H2O & Exempt Solvents0 g/l [Test Method:calculated SCAQMD rule 443.1] [Details:when used as intended with Part B] VOC Less H2O & Exempt Solvents0 g/l [Test Method:calculated SCAQMD rule 443.1] [ Details:as supplied] Molecular weightNo Data Available SECTION 10: Stability and reactivity 10.1. Reactivity This material may be reactive with certain agents under certain conditions - see the remaining headings in this section. 10.2. Chemical stability 3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE DP-460 NS (Part A) __________________________________________________________________________________________ Page: 6 of 10 Stable. 10.3. Possibility of hazardous reactions Hazardous polymerization will not occur. 10.4. Conditions to avoid None known. 10.5. Incompatible materials Amines Alcohols Strong bases Strong acids Strong oxidizing agents 10.6. Hazardous decomposition products SubstanceCondition None known. Refer to section 5.2 for hazardous decomposition products during combustion. SECTION 11: Toxicological information The information below may not be consistent with the material classification in Section 2 if specific ingredient classifications are mandated by a competent authority. In addition, toxicological data on ingredients may not be reflected in the material classification and/or the signs and symptoms of exposure, because an ingredient may be present below the threshold for labeling, an ingredient may not be available for exposure, or the data may not be relevant to the material as a whole. 11.1. Information on Toxicological effects Signs and Symptoms of Exposure Based on test data and/or information on the components, this material may produce the following health effects: Inhalation: Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain. Skin Contact: Corrosive (Skin Burns): Signs/symptoms may include localized redness, swelling, itching, intense pain, blistering, ulceration, and tissue destruction. Allergic Skin Reaction (non-photo induced): Signs/symptoms may include redness, swelling, blistering, and itching. Eye Contact: Corrosive (Eye Burns): Signs/symptoms may include cloudy appearance of the cornea, chemical burns, severe pain, tearing, ulcerations, significantly impaired vision or complete loss of vision. Ingestion: Gastrointestinal Corrosion: Signs/symptoms may include severe mouth, throat and abdominal pain; nausea; vomiting; and diarrhea; blood in the feces and/or vomitus may also be seen. Additional Information: Persons previously sensitized to amines may develop a cross-sensitization reaction to certain other amines. Toxicological Data 3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE DP-460 NS (Part A) __________________________________________________________________________________________ Page: 7 of 10 If a component is disclosed in section 3 but does not appear in a table below, either no data are available for that endpoint or the data are not sufficient for classification. Acute Toxicity NameRouteSpeciesValueOverall productDermalNo data available; calculated ATE >5,000 mg/kgOverall productIngestionNo data available; calculated ATE >5,000 mg/kg4,7,10-Trioxatridecane-1,13-DiamineDermalRabbitLD50 2,525 mg/kg4,7,10-Trioxatridecane-1,13-DiamineIngestionRatLD50 2,850 mg/kgAmorphous SilicaDermalRabbitLD50 > 5,000 mg/kgAmorphous SilicaInhalation-
Dust/Mist
(4 hours)
RatLC50 > 0.691 mg/lAmorphous SilicaIngestionRatLD50 > 5,110 mg/kg2,4,6-tris((Dimethylamino)-Methyl)PhenolDermalRatLD50 1,280 mg/kg2,4,6-tris((Dimethylamino)-Methyl)PhenolIngestionRatLD50 1,000 mg/kg
ATE = acute toxicity estimate
Skin Corrosion/Irritation
NameSpeciesValueOverall productIn vitro
data
Corrosive4,7,10-Trioxatridecane-1,13-DiamineRabbitCorrosiveAmorphous SilicaRabbitNo significant irritation2,4,6-tris((Dimethylamino)-Methyl)PhenolRabbitCorrosive
Serious Eye Damage/Irritation
NameSpeciesValue4,7,10-Trioxatridecane-1,13-DiamineRabbitCorrosiveAmorphous SilicaRabbitNo significant irritation2,4,6-tris((Dimethylamino)-Methyl)PhenolRabbitCorrosive
Skin Sensitization
NameSpeciesValue4,7,10-Trioxatridecane-1,13-DiamineProfessio
nal
judgeme
nt
SensitizingAmorphous SilicaHuman
and
animal
Not classified2,4,6-tris((Dimethylamino)-Methyl)PhenolGuinea
pig
Not classified
Respiratory Sensitization
For the component/components, either no data are currently available or the data are not sufficient for classification.
Germ Cell Mutagenicity
NameRouteValueOverall productIn VitroNot mutagenic4,7,10-Trioxatridecane-1,13-DiamineIn VitroNot mutagenicAmorphous SilicaIn VitroNot mutagenic2,4,6-tris((Dimethylamino)-Methyl)PhenolIn VitroNot mutagenic
Carcinogenicity
NameRouteSpeciesValueAmorphous SilicaNot
Specified
MouseSome positive data exist, but the data are not
sufficient for classification

3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE DP-460 NS (Part A)
__________________________________________________________________________________________
Page: 8 of 10
Reproductive Toxicity
Reproductive and/or Developmental Effects
NameRouteValueSpeciesTest result Exposure
Duration
4,7,10-Trioxatridecane-1,13-DiamineIngestionNot classified for female reproductionRatNOAEL 600
mg/kg/day
premating
into lactation
4,7,10-Trioxatridecane-1,13-DiamineIngestionNot classified for male reproductionRatNOAEL 600
mg/kg/day
59 days4,7,10-Trioxatridecane-1,13-DiamineIngestionNot classified for developmentRatNOAEL 600
mg/kg/day
premating
into lactation
Amorphous SilicaIngestionNot classified for female reproductionRatNOAEL 509
mg/kg/day
1 generationAmorphous SilicaIngestionNot classified for male reproductionRatNOAEL 497
mg/kg/day
1 generationAmorphous SilicaIngestionNot classified for developmentRatNOAEL 1,350
mg/kg/day
during
organogenesi
s
Target Organ(s)
Specific Target Organ Toxicity – single exposure
NameRouteTarget Organ(s)ValueSpeciesTest result Exposure
Duration
4,7,10-Trioxatridecane-
1,13-Diamine
Inhalationrespiratory irritationSome positive data exist, but the
data are not sufficient for
classification
similar
health
hazards
NOAEL Not
available
2,4,6-
tris((Dimethylamino)-
Methyl)Phenol
Inhalationrespiratory irritationSome positive data exist, but the
data are not sufficient for
classification
NOAEL Not
available
Specific Target Organ Toxicity – repeated exposure
NameRouteTarget Organ(s)ValueSpeciesTest result Exposure
Duration
4,7,10-Trioxatridecane-
1,13-Diamine
Ingestiongastrointestinal tract
| heart | endocrine
system | bone, teeth,
nails, and/or hair |
hematopoietic
system | liver |
immune system |
muscles | nervous
system | eyes |
kidney and/or
bladder | respiratory
system | vascular
system
Not classifiedRatNOAEL 600
mg/kg/day
59 daysAmorphous SilicaInhalationrespiratory system |
silicosis
Not classifiedHumanNOAEL Not
available
occupational
exposure
2,4,6-
tris((Dimethylamino)-
Methyl)Phenol
Dermalskin | liver | nervous
system | auditory
system |
hematopoietic
system | eyes
Not classifiedRatNOAEL 125
mg/kg/day
28 days
Aspiration Hazard
For the component/components, either no data are currently available or the data are not sufficient for classification.
Please contact the address or phone number listed on the first page of the SDS for additional toxicological information
on this material and/or its components.
SECTION 12: Ecological information

3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE DP-460 NS (Part A)
__________________________________________________________________________________________
Page: 9 of 10
No data available.
SECTION 13: Disposal considerations
13.1. Disposal methods
Dispose of contents/ container in accordance with the local/regional/national/international regulations.
Dispose of completely cured (or polymerized) material in a permitted industrial waste facility. As a disposal alternative,
incinerate uncured product in a permitted waste incineration facility. Proper destruction may require the use of additional fuel
during incineration processes. Combustion products will include halogen acid (HCl/HF/HBr). Facility must be capable of
handling halogenated materials. Empty drums/barrels/containers used for transporting and handling hazardous chemicals
(chemical substances/mixtures/preparations classified as Hazardous as per applicable regulations) shall be considered,
stored, treated & disposed of as hazardous wastes unless otherwise defined by applicable waste regulations. Consult with the
respective regulating authorities to determine the available treatment and disposal facilities.
SECTION 14: Transport Information

For Transport Information, please visit http://3M.com/Transportinfo or call 1-800-364-3577 or 651-737-6501.
SECTION 15: Regulatory information
15.1. Safety, health and environmental regulations/legislation specific for the substance or mixture
Global inventory status
Contact 3M for more information. The components of this material are in compliance with the provisions of Philippines RA
6969 requirements. Certain restrictions may apply. Contact the selling division for additional information. This product
complies with Measures on Environmental Management of New Chemical Substances. All ingredients are listed on or exempt
from on China IECSC inventory. The components of this product are in compliance with the chemical notification
requirements of TSCA. All required components of this product are listed on the active portion of the TSCA Inventory.
SECTION 16: Other information
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to
address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or
similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material
but also include the toxic properties of combustion or decomposition products that are known to be generated in
significant quantities.
Health: 3 Flammability: 1 Instability: 0 Special Hazards: None

National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address
the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar
emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include
the toxic properties of combustion or decomposition products that are known to be generated in significant quantities.

Document group:22-0536-7Version number:13.01Issue Date:2024/02/05Supercedes Date:2022/10/26
The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. The manufacturer MAKES
NO WARRANTIES, EXPRESS OR IMPLIED, STATUTORY OR OTHERWISE, INCLUDING, BUT NOT LIMITED TO,
ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

3M(TM) SCOTCH-WELD(TM) EPOXY ADHESIVE DP-460 NS (Part A)
__________________________________________________________________________________________
Page: 10 of 10
PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF A COURSE OF PERFORMANCE,
COURSE OF DEALING, CUSTOM OR USAGE OF TRADE. User is responsible for determining whether the product is fit
for a particular purpose and suitable for user’s method of use or application. Given the variety of factors that can affect the use
and application of a product, some of which are uniquely within the user’s knowledge and control, it is essential that the user
evaluate the product to determine whether it is fit for a particular purpose and suitable for user’s method of use or application.
3M Canada SDSs are available at www.3M.ca

3M Scotch-Weld Epoxy Adhesive 460NS Off-White, Part B
__________________________________________________________________________________________
Page: 1 of 10
Safety Data Sheet
Copyright,2023, 3M Canada Company. All rights reserved. Copying and/or downloading of this information for
the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes
unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed
with the intention of earning a profit thereon.
Document group:09-0979-6 Version number:10.00Issue Date:2023/02/24Supercedes Date:2021/11/10
This Safety Data Sheet has been prepared in accordance with the Canadian Hazardous Products Regulations.
SECTION 1: Identification
1.1. Product identifier
3M Scotch-Weld Epoxy Adhesive 460NS Off-White, Part B
Product Identification Numbers
LA-D100-2246-3 LA-D100-0014-7 LA-D100-0014-8 LA-D100-0123-8 LA-D100-0309-5 62-2792-8530-8 62-2792-9530-7
1.2. Recommended use and restrictions on use
Intended Use
Structural adhesive
Specific Use
Part B of 2 part adhesive system.
Restrictions on use
Not applicable
1.3. Supplier s details
Company:3M Canada CompanyDivision:Industrial Adhesives and Tapes DivisionAddress:1840 Oxford Street East, Post Office Box 5757, London, Ontario N6A 4T1Telephone:(800) 364-3577Website:www.3M.ca
1.4. Emergency telephone number
Medical Emergency Telephone:1-800-3M HELPS / 1-800-364-3577; Transportation Emergency Telephone (CANUTEC):
(613) 996-6666
SECTION 2: Hazard identification
2.1. Classification of the substance or mixture
Serious Eye Damage/Irritation: Category 2B.
Skin Sensitizer: Category 1.
2.2. Label elements

3M Scotch-Weld Epoxy Adhesive 460NS Off-White, Part B
__________________________________________________________________________________________
Page: 2 of 10
Signal word
Warning
Symbols
Exclamation mark |
Pictograms
Hazard statements
Causes eye irritation. May cause an allergic skin reaction.
Precautionary statements
Prevention:
Avoid breathing dust/fume/gas/mist/vapours/spray. Wear protective gloves. Wash exposed skin thoroughly after handling.
Contaminated work clothing must not be allowed out of the workplace.
Response:
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.
Continue rinsing. If eye irritation persists: Get medical advice/attention. IF ON SKIN: Wash with plenty of soap and
water. If skin irritation or rash occurs: Get medical advice/attention. Take off contaminated clothing and wash it before
reuse.
Disposal:
Dispose of contents/container in accordance with applicable local/regional/national/international regulations.
2.3. Other hazards
None known.
SECTION 3: Composition/information on ingredients
This material is a mixture.
IngredientC.A.S. No.% by WtCommon NameEpoxy Resin25068-38-6 80 – 100 Trade Secret *Phenol, 4,4′-(1-methylethylidene)bis-,
polymer with (chloromethyl)oxirane
Acrylic PolymerTrade Secret < 20Not ApplicableAmorphous Silica67762-90-7 1 - 5Siloxanes and Silicones, di-Me, reaction products with silica 3-(trimethoxysilyl)propyl glycidyl ether 2530-83-8 <= 0.5Silane, trimethoxy[3- (oxiranylmethoxy)propyl]- Acrylic Polymer is a non-hazardous Trade Secret material according to WHMIS criteria. *The actual concentration of this ingredient has been withheld as a trade secret. SECTION 4: First aid measures 4.1. Description of first aid measures 3M Scotch-Weld Epoxy Adhesive 460NS Off-White, Part B __________________________________________________________________________________________ Page: 3 of 10 Inhalation: Remove person to fresh air. If you feel unwell, get medical attention. Skin Contact: Immediately wash with soap and water. Remove contaminated clothing and wash before reuse. If signs/symptoms develop, get medical attention. Eye Contact: Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get medical attention. If Swallowed: Rinse mouth. If you feel unwell, get medical attention. 4.2. Most important symptoms and effects, both acute and delayed Allergic skin reaction (redness, swelling, blistering, and itching). 4.3. Indication of any immediate medical attention and special treatment required Not applicable SECTION 5: Fire-fighting measures 5.1. Suitable extinguishing media In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish. 5.2. Special hazards arising from the substance or mixture None inherent in this product. Hazardous Decomposition or By-Products Substance ConditionAldehydesDuring CombustionCarbon monoxideDuring CombustionCarbon dioxideDuring CombustionHydrogen ChlorideDuring Combustion 5.3. Special protective actions for fire-fighters Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus (SCBA). Wear full protective clothing, including helmet, self-contained, positive pressure or pressure demand breathing apparatus, bunker coat and pants, bands around arms, waist and legs, face mask, and protective covering for exposed areas of the head. SECTION 6: Accidental release measures 6.1. Personal precautions, protective equipment and emergency procedures Evacuate area. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to disperse or exhaust vapours, in accordance with good industrial hygiene practice. Refer to other sections of this SDS for information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment. 6.2. Environmental precautions Avoid release to the environment. For larger spills, cover drains and build dikes to prevent entry into sewer systems or bodies of water. 6.3. Methods and material for containment and cleaning up Contain spill. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent material does not remove a physical, health, or environmental hazard. Collect as much of the spilled material as possible. Place in a closed container approved for transportation by appropriate authorities. Clean up residue with an appropriate 3M Scotch-Weld Epoxy Adhesive 460NS Off-White, Part B __________________________________________________________________________________________ Page: 4 of 10 solvent selected by a qualified and authorized person. Ventilate the area with fresh air. Read and follow safety precautions on the solvent label and SDS. Seal the container. Dispose of collected material as soon as possible in accordance with applicable local/regional/national/international regulations. SECTION 7: Handling and storage 7.1. Precautions for safe handling For industrial or professional use only. Not for consumer sale or use. Avoid breathing dust/fume/gas/mist/vapours/spray. Do not get in eyes, on skin, or on clothing. Do not eat, drink or smoke when using this product. Wash thoroughly after handling. Contaminated work clothing should not be allowed out of the workplace. Avoid release to the environment. Wash contaminated clothing before reuse. Avoid contact with oxidizing agents (eg. chlorine, chromic acid etc.) 7.2. Conditions for safe storage including any incompatibilities Store away from heat. Store away from oxidizing agents. SECTION 8: Exposure controls/personal protection 8.1. Control parameters Occupational exposure limits No occupational exposure limit values exist for any of the components listed in Section 3 of this SDS. 8.2. Exposure controls 8.2.1. Engineering controls Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below relevant Exposure Limits and/or control dust/fume/gas/mist/vapours/spray. If ventilation is not adequate, use respiratory protection equipment. 8.2.2. Personal protective equipment (PPE) Eye/face protection Select and use eye/face protection to prevent contact based on the results of an exposure assessment. The following eye/face protection(s) are recommended: Safety Glasses with side shields Indirect Vented Goggles Skin/hand protection Select and use gloves and/or protective clothing approved to relevant local standards to prevent skin contact based on the results of an exposure assessment. Selection should be based on use factors such as exposure levels, concentration of the substance or mixture, frequency and duration, physical challenges such as temperature extremes, and other use conditions. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible gloves/protective clothing. Note: Nitrile gloves may be worn over polymer laminate gloves to improve dexterity. Gloves made from the following material(s) are recommended: Polymer laminate If this product is used in a manner that presents a higher potential for exposure (eg. spraying, high splash potential etc.), then use of protective coveralls may be necessary. Select and use body protection to prevent contact based on the results of an exposure assessment. The following protective clothing material(s) are recommended: Apron - polymer laminate Respiratory protection An exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part of a full respiratory protection program. Based on the results of the exposure assessment, select from the following respirator type(s) to reduce inhalation exposure: Half facepiece or full facepiece air-purifying respirator suitable for organic vapours and particulates 3M Scotch-Weld Epoxy Adhesive 460NS Off-White, Part B __________________________________________________________________________________________ Page: 5 of 10 For questions about suitability for a specific application, consult with your respirator manufacturer. SECTION 9: Physical and chemical properties 9.1. Information on basic physical and chemical properties Physical stateLiquid Specific Physical Form: PasteColourWhiteOdourEpoxyOdour thresholdNo Data AvailablepHNot ApplicableMelting point/Freezing pointNot ApplicableBoiling point>=260 CFlash Point248.9 C [ Test Method:Closed Cup]Evaporation rateNot ApplicableFlammability (solid, gas)Not ApplicableFlammable Limits(LEL)Not ApplicableFlammable Limits(UEL)Not ApplicableVapour PressureNot ApplicableVapour Density and/or Relative Vapour DensityNot ApplicableDensity1.17 g/mlRelative density1.17 [Ref Std:WATER=1]Water solubilityNilSolubility- non-waterNo Data AvailablePartition coefficient: n-octanol/ waterNo Data AvailableAutoignition temperatureNo Data AvailableDecomposition temperatureNo Data AvailableViscosity/Kinematic Viscosity160,000 – 260,000 mPa-s [@ 23 C ]Volatile Organic CompoundsNo Data AvailablePercent volatileNo Data AvailableVOC Less H2O & Exempt Solvents0 g/l [Test Method:calculated SCAQMD rule 443.1]
[Details:when used as intended with Part A]
VOC Less H2O & Exempt Solvents6 g/l [Test Method:calculated SCAQMD rule 443.1] [ Details:as
supplied]
VOC Less H2O & Exempt Solvents0 % [Test Method:calculated SCAQMD rule 443.1]
[Details:when used as intended with Part A]
Molecular weightNot Applicable
SECTION 10: Stability and reactivity
10.1. Reactivity
This material may be reactive with certain agents under certain conditions – see the remaining headings in this section.
10.2. Chemical stability
Stable.

10.3. Possibility of hazardous reactions
Hazardous polymerization will not occur.
10.4. Conditions to avoid
Heat

3M Scotch-Weld Epoxy Adhesive 460NS Off-White, Part B
__________________________________________________________________________________________
Page: 6 of 10

10.5. Incompatible materials
Strong oxidizing agents
10.6. Hazardous decomposition products
SubstanceCondition None known.
Refer to section 5.2 for hazardous decomposition products during combustion.
SECTION 11: Toxicological information
The information below may not be consistent with the material classification in Section 2 if specific ingredient
classifications are mandated by a competent authority. In addition, toxicological data on ingredients may not be
reflected in the material classification and/or the signs and symptoms of exposure, because an ingredient may be
present below the threshold for labeling, an ingredient may not be available for exposure, or the data may not be
relevant to the material as a whole.
11.1. Information on Toxicological effects
Signs and Symptoms of Exposure
Based on test data and/or information on the components, this material may produce the following health effects:
Inhalation:
Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose
and throat pain.
Skin Contact:
Mild Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness. Allergic Skin Reaction
(non-photo induced): Signs/symptoms may include redness, swelling, blistering, and itching.
Eye Contact:
Moderate Eye Irritation: Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision.
Ingestion:
Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.
Toxicological Data
If a component is disclosed in section 3 but does not appear in a table below, either no data are available for that endpoint or
the data are not sufficient for classification.
Acute Toxicity
NameRouteSpeciesValueOverall productIngestionNo data available; calculated ATE >5,000 mg/kgEpoxy ResinDermalRatLD50 > 1,600 mg/kgEpoxy ResinIngestionRatLD50 > 1,000 mg/kgAcrylic PolymerDermalRabbitLD50 > 5,000 mg/kgAcrylic PolymerIngestionRatLD50 > 5,000 mg/kgAmorphous SilicaDermalRabbitLD50 > 5,000 mg/kgAmorphous SilicaInhalation-
Dust/Mist
(4 hours)
RatLC50 > 0.691 mg/lAmorphous SilicaIngestionRatLD50 > 5,110 mg/kg3-(trimethoxysilyl)propyl glycidyl etherDermalRabbitLD50 4,000 mg/kg3-(trimethoxysilyl)propyl glycidyl etherInhalation-
Dust/Mist
(4 hours)
RatLC50 > 5.3 mg/l

3M Scotch-Weld Epoxy Adhesive 460NS Off-White, Part B
__________________________________________________________________________________________
Page: 7 of 10
3-(trimethoxysilyl)propyl glycidyl etherIngestionRatLD50 7,010 mg/kg
ATE = acute toxicity estimate
Skin Corrosion/Irritation
NameSpeciesValueEpoxy ResinRabbitMild irritantAcrylic PolymerProfessio
nal
judgeme
nt
Minimal irritationAmorphous SilicaRabbitNo significant irritation3-(trimethoxysilyl)propyl glycidyl etherRabbitMild irritant
Serious Eye Damage/Irritation
NameSpeciesValueEpoxy ResinRabbitModerate irritantAcrylic PolymerProfessio
nal
judgeme
nt
Mild irritantAmorphous SilicaRabbitNo significant irritation3-(trimethoxysilyl)propyl glycidyl etherRabbitCorrosive
Skin Sensitization
NameSpeciesValueEpoxy ResinHuman
and
animal
SensitizingAmorphous SilicaHuman
and
animal
Not classified3-(trimethoxysilyl)propyl glycidyl etherGuinea
pig
Not classified
Respiratory Sensitization
NameSpeciesValueEpoxy ResinHumanNot classified
Germ Cell Mutagenicity
NameRouteValueEpoxy ResinIn vivoNot mutagenicEpoxy ResinIn VitroSome positive data exist, but the data are not
sufficient for classification
Amorphous SilicaIn VitroNot mutagenic3-(trimethoxysilyl)propyl glycidyl etherIn vivoNot mutagenic3-(trimethoxysilyl)propyl glycidyl etherIn VitroSome positive data exist, but the data are not
sufficient for classification
Carcinogenicity
NameRouteSpeciesValueEpoxy ResinDermalMouseSome positive data exist, but the data are not
sufficient for classification
Amorphous SilicaNot
Specified
MouseSome positive data exist, but the data are not
sufficient for classification
3-(trimethoxysilyl)propyl glycidyl etherDermalMouseNot carcinogenic
Reproductive Toxicity

3M Scotch-Weld Epoxy Adhesive 460NS Off-White, Part B
__________________________________________________________________________________________
Page: 8 of 10
Reproductive and/or Developmental Effects
NameRouteValueSpeciesTest result Exposure
Duration
Epoxy ResinIngestionNot classified for female reproductionRatNOAEL 750
mg/kg/day
2 generationEpoxy ResinIngestionNot classified for male reproductionRatNOAEL 750
mg/kg/day
2 generationEpoxy ResinDermalNot classified for developmentRabbitNOAEL 300
mg/kg/day
during
organogenesi
s
Epoxy ResinIngestionNot classified for developmentRatNOAEL 750
mg/kg/day
2 generationAmorphous SilicaIngestionNot classified for female reproductionRatNOAEL 509
mg/kg/day
1 generationAmorphous SilicaIngestionNot classified for male reproductionRatNOAEL 497
mg/kg/day
1 generationAmorphous SilicaIngestionNot classified for developmentRatNOAEL 1,350
mg/kg/day
during
organogenesi
s
3-(trimethoxysilyl)propyl glycidyl etherIngestionNot classified for female reproductionRatNOAEL 1,000
mg/kg/day
1 generation3-(trimethoxysilyl)propyl glycidyl etherIngestionNot classified for male reproductionRatNOAEL 1,000
mg/kg/day
1 generation3-(trimethoxysilyl)propyl glycidyl etherIngestionNot classified for developmentRatNOAEL 3,000
mg/kg/day
during
organogenesi
s
Target Organ(s)
Specific Target Organ Toxicity – single exposure
For the component/components, either no data are currently available or the data are not sufficient for classification.
Specific Target Organ Toxicity – repeated exposure
NameRouteTarget Organ(s)ValueSpeciesTest result Exposure
Duration
Epoxy ResinDermalliverNot classifiedRatNOAEL
1,000
mg/kg/day
2 yearsEpoxy ResinDermalnervous systemNot classifiedRatNOAEL
1,000
mg/kg/day
13 weeksEpoxy ResinIngestionauditory system |
heart | endocrine
system |
hematopoietic
system | liver | eyes |
kidney and/or
bladder
Not classifiedRatNOAEL
1,000
mg/kg/day
28 daysAmorphous SilicaInhalationrespiratory system |
silicosis
Not classifiedHumanNOAEL Not
available
occupational
exposure
3-(trimethoxysilyl)propyl
glycidyl ether
Ingestionheart | endocrine
system | bone, teeth,
nails, and/or hair |
hematopoietic
system | liver |
immune system |
nervous system |
kidney and/or
bladder | respiratory
system
Not classifiedRatNOAEL
1,000
mg/kg/day
28 days
Aspiration Hazard
For the component/components, either no data are currently available or the data are not sufficient for classification.
Please contact the address or phone number listed on the first page of the SDS for additional toxicological information

3M Scotch-Weld Epoxy Adhesive 460NS Off-White, Part B
__________________________________________________________________________________________
Page: 9 of 10
on this material and/or its components.
SECTION 12: Ecological information
No data available.
SECTION 13: Disposal considerations
13.1. Disposal methods
Dispose of contents/ container in accordance with the local/regional/national/international regulations.
Dispose of completely cured (or polymerized) material in a permitted industrial waste facility. As a disposal alternative,
incinerate uncured product in a permitted waste incineration facility. Proper destruction may require the use of additional fuel
during incineration processes. Combustion products will include halogen acid (HCl/HF/HBr). Facility must be capable of
handling halogenated materials. Empty drums/barrels/containers used for transporting and handling hazardous chemicals
(chemical substances/mixtures/preparations classified as Hazardous as per applicable regulations) shall be considered,
stored, treated & disposed of as hazardous wastes unless otherwise defined by applicable waste regulations. Consult with the
respective regulating authorities to determine the available treatment and disposal facilities.
SECTION 14: Transport Information

For Transport Information, please visit http://3M.com/Transportinfo or call 1-800-364-3577 or 651-737-6501.
SECTION 15: Regulatory information
15.1. Safety, health and environmental regulations/legislation specific for the substance or mixture
Global inventory status
Contact 3M for more information. The components of this material are in compliance with the provisions of the Korea
Chemical Control Act. Certain restrictions may apply. Contact the selling division for additional information. The
components of this material are in compliance with the provisions of Australia National Industrial Chemical Notification and
Assessment Scheme (NICNAS). Certain restrictions may apply. Contact the selling division for additional information. The
components of this material are in compliance with the provisions of Japan Chemical Substance Control Law. Certain
restrictions may apply. Contact the selling division for additional information. The components of this material are in
compliance with the provisions of Philippines RA 6969 requirements. Certain restrictions may apply. Contact the selling
division for additional information. The components of this product are in compliance with the new substance notification
requirements of CEPA. This product complies with Measures on Environmental Management of New Chemical
Substances. All ingredients are listed on or exempt from on China IECSC inventory. The components of this product are in
compliance with the chemical notification requirements of TSCA. All required components of this product are listed on the
active portion of the TSCA Inventory.
SECTION 16: Other information
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to
address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or
similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material
but also include the toxic properties of combustion or decomposition products that are known to be generated in
significant quantities.
Health: 2 Flammability: 1 Instability: 0 Special Hazards: None

National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address

3M Scotch-Weld Epoxy Adhesive 460NS Off-White, Part B
__________________________________________________________________________________________
Page: 10 of 10
the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar
emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include
the toxic properties of combustion or decomposition products that are known to be generated in significant quantities.

Document group:09-0979-6Version number:10.00Issue Date:2023/02/24Supercedes Date:2021/11/10
The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. The manufacturer MAKES
NO WARRANTIES, EXPRESS OR IMPLIED, STATUTORY OR OTHERWISE, INCLUDING, BUT NOT LIMITED TO,
ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF A COURSE OF PERFORMANCE,
COURSE OF DEALING, CUSTOM OR USAGE OF TRADE. User is responsible for determining whether the product is fit
for a particular purpose and suitable for user’s method of use or application. Given the variety of factors that can affect the use
and application of a product, some of which are uniquely within the user’s knowledge and control, it is essential that the user
evaluate the product to determine whether it is fit for a particular purpose and suitable for user’s method of use or application.
3M Canada SDSs are available at www.3M.ca

233M43671_SDS.pdf