by | Sep 27, 2025
435 Harrison Street, Elkhart, IN 46516-2717 Page 1 of 2
www.bigdogadhesives.com Ph: 574-350-2237 January 2024
TECHNICAL DATA SHEET
1. DESCRIPTION
BD8110 is a two-part structural methacrylate adhesive specially designed for the bonding of various
metals. Apart from this it can be used in bonding, plastics and composites. BD8110 provides high
bond strength to the above reference surfaces with generally no preparation effort. It provides high
strength with excellent toughness and fatigue resistance. BD8110 is highly recommended for coated
galvanized such as G60, G70, G90 and also other zinc coated metals, Aluminum, FRP, ABS and
Polyesters. It is available with and without spacers/glass beads.
Company Identification: Big Dog Adhesives LLC.
435 Harrison Street
Elkhart, IN 46516-2717
Phone: 574-350-2237
Website: www.bigdogadhesives.com sales@bigdogadhesives.com
2. CHARACTERISTICS :
Room Temperature Cure Properties
Working Time 8 -12 minutes (at 75 F/ 24 C)
Fixture Time 18 -22 minutes (at 75 F/ 24 C)
Can be Moved In 30 minutes
Operating Temp. -40 F to 180 F (40 C to 82 C)
Gap Filling .375 inches (3/8 inch)
Mixed Density 8.1 lbs/gal (.96 g/cc)
Flash Point 51 F (11 C) See SDS for more safety information
VOC <1%
Shore D Hardness 70-75
3. CHEMICAL RESISTANCE:
Excellent Resistance to: Susceptible to:
Hydrocarbons Polar Solvents
Acids and Bases Super Strong Acids and Bases
Vinegar
Wine and Condiments
Salt Solutions
4. PHYSICAL PROPERTIES:
Uncured: Resin Activator
Viscosity(cps) 70,000-120,000 50000-100,000
Color Off White Gray
Density (lbs/gal) 8.2 8.0
Mix Ratio (wt or vol) 1.0 1.0
Mixer Recommendation Cartridge (200/400ml): MFQX 08-24T Square 24 element
White/Green Mix Tips (1:1)
BD8110 Structural Methacrylate Adhesive
435 Harrison Street, Elkhart, IN 46516-2717 Page 2 of 2
www.bigdogadhesives.com Ph: 574-350-2237 January 2024
TECHNICAL DATA SHEET
5. MECHANICAL PROPERTIES:
Lap Shear Strength (ASTM D638) Substrate Results Failure Type
Strength, psi Steel/Stainless Steel 2,500 3,000 Cohesive
Strength, psi Aluminum 2,500 3,000 Cohesive
Strength, psi G70 2,000 2,500 Cohesive
6. HANDLING AND APPLICATION:
BD81110 resin (Part A) and activator (Part B) are flammable. Contents include Methacrylate ester
and acids. Keep containers closed after use. Wear gloves and safety glasses to avoid skin and eye
contact. Wash with soap and water after skin contact. In case of eye contact, flush with water for 15
minutes and get medical attention. Harmful if swallowed. Keep out of the reach of children. Keep
away from heat, sparks, and open flames. Do not smoke cigarettes or anything else while handling or
near the product. Refer to the BD8110 Safety Data Sheet for more complete safety instruction. To
assure maximum bond strength, surfaces must be mated together within the specified working time,
and all clamps affixed within that time. Use sufficient material to ensure that the joint is completely
filled when parts are mated and clamped. Avoid over clamping parts, which may cause a dry joint or
a joint starved of adhesive. All adhesive application, part positioning, fixturing, and clamping should
occur before the working time of the adhesive has expired. After the indicated working time, parts
must remain undisturbed until the fixture time is completed. Components bonded, adhesive, and
shop temperature can have a significant effect on the work and fixture time of the adhesive.
Application of BD8110 adhesive at temperatures between 65 F and 85 F (18 C and 30 C) will ensure
proper cure. Temperatures below 65 F (18 C) will slow cure and fixture speed. BD8110 adhesives
will still react, but will take longer. Temperatures above 85 F (18 C and 30 C) will increase cure and
fixture speeds, and there s a risk that the adhesive will be hardened or too thick to bond materials.
The viscosities of BD8110 adhesives are affected by temperature.
NOTE: Because of the curing features of BD8110 adhesives, large amounts of heat are generated
when large masses of material are mixed at one time. The heat generated by the exotherm resulting
from mixing large amounts of adhesive can result in a boiling of the monomer in the adhesive (methyl
methacrylate), resulting in the release of trapped air, steam and volatile gasses. To prevent this, use
only enough material as needed for use within the working time for the product, and confine the gap
or spread out the material to no more than .50 inches.
7. HANDLING AND STORAGE
The shelf life of BD8110 is nine (9) months from the date of manufacture based upon continuous
storage at room temperature (77 F or 25 C). Storage of BD8110 adhesives in refrigerated
compartments will extend the shelf life even more. Do not store BD8110 adhesive or any other
adhesives in a refrigerator which has food or lunch products in them. Be sure to bring BD8110
adhesives to room temperature for 24 hours before use, otherwise longer cure and fixture times may
be expected. Long-term storage at temperatures above room temperature will shorten the shelf life of
BD8110 adhesives considerably. Storage at temperatures above 100 F or 38 C could shorten the
shelf life to less than one month. BD8110 adhesives contain no water, so freezing of the adhesive for
short periods is permissible, but is not encouraged.
8. ADDITIONAL INFORMATION
NOTE: Information contained herein is based on tests we believe to be reliable and accurate. It is
offered in good faith for the benefit of the consumer. The Company shall not be liable for any injury,
loss, or damage in the use or handling of its chemical products since conditions and use are beyond
our control. In every case, we urge and recommend the user conduct tests to determine to their
own satisfaction that the product is of acceptable quality and suitability for their particular purpose
under their own operating conditions. Statements concerning possible use of our products are not
intended as recommendations to use our products in the infringement of any patent, or for any
particular purpose or application. These products are intended for industrial use only.
by | Sep 27, 2025
435 Harrison Street, Elkhart, IN 46516-2717 Page 1 of 2
www.bigdogadhesives.com Ph: 574-350-2237 January 2024
TECHNICAL DATA SHEET
1. DESCRIPTION
BD8110 is a two-part structural methacrylate adhesive specially designed for the bonding of various
metals. Apart from this it can be used in bonding, plastics and composites. BD8110 provides high
bond strength to the above reference surfaces with generally no preparation effort. It provides high
strength with excellent toughness and fatigue resistance. BD8110 is highly recommended for coated
galvanized such as G60, G70, G90 and also other zinc coated metals, Aluminum, FRP, ABS and
Polyesters. It is available with and without spacers/glass beads.
Company Identification: Big Dog Adhesives LLC.
435 Harrison Street
Elkhart, IN 46516-2717
Phone: 574-350-2237
Website: www.bigdogadhesives.com sales@bigdogadhesives.com
2. CHARACTERISTICS :
Room Temperature Cure Properties
Working Time 8 -12 minutes (at 75 F/ 24 C)
Fixture Time 18 -22 minutes (at 75 F/ 24 C)
Can be Moved In 30 minutes
Operating Temp. -40 F to 180 F (40 C to 82 C)
Gap Filling .375 inches (3/8 inch)
Mixed Density 8.1 lbs/gal (.96 g/cc)
Flash Point 51 F (11 C) See SDS for more safety information
VOC <1%
Shore D Hardness 70-75
3. CHEMICAL RESISTANCE:
Excellent Resistance to: Susceptible to:
Hydrocarbons Polar Solvents
Acids and Bases Super Strong Acids and Bases
Vinegar
Wine and Condiments
Salt Solutions
4. PHYSICAL PROPERTIES:
Uncured: Resin Activator
Viscosity(cps) 70,000-120,000 50000-100,000
Color Off White Gray
Density (lbs/gal) 8.2 8.0
Mix Ratio (wt or vol) 1.0 1.0
Mixer Recommendation Cartridge (200/400ml): MFQX 08-24T Square 24 element
White/Green Mix Tips (1:1)
BD8110 Structural Methacrylate Adhesive
435 Harrison Street, Elkhart, IN 46516-2717 Page 2 of 2
www.bigdogadhesives.com Ph: 574-350-2237 January 2024
TECHNICAL DATA SHEET
5. MECHANICAL PROPERTIES:
Lap Shear Strength (ASTM D638) Substrate Results Failure Type
Strength, psi Steel/Stainless Steel 2,500 3,000 Cohesive
Strength, psi Aluminum 2,500 3,000 Cohesive
Strength, psi G70 2,000 2,500 Cohesive
6. HANDLING AND APPLICATION:
BD81110 resin (Part A) and activator (Part B) are flammable. Contents include Methacrylate ester
and acids. Keep containers closed after use. Wear gloves and safety glasses to avoid skin and eye
contact. Wash with soap and water after skin contact. In case of eye contact, flush with water for 15
minutes and get medical attention. Harmful if swallowed. Keep out of the reach of children. Keep
away from heat, sparks, and open flames. Do not smoke cigarettes or anything else while handling or
near the product. Refer to the BD8110 Safety Data Sheet for more complete safety instruction. To
assure maximum bond strength, surfaces must be mated together within the specified working time,
and all clamps affixed within that time. Use sufficient material to ensure that the joint is completely
filled when parts are mated and clamped. Avoid over clamping parts, which may cause a dry joint or
a joint starved of adhesive. All adhesive application, part positioning, fixturing, and clamping should
occur before the working time of the adhesive has expired. After the indicated working time, parts
must remain undisturbed until the fixture time is completed. Components bonded, adhesive, and
shop temperature can have a significant effect on the work and fixture time of the adhesive.
Application of BD8110 adhesive at temperatures between 65 F and 85 F (18 C and 30 C) will ensure
proper cure. Temperatures below 65 F (18 C) will slow cure and fixture speed. BD8110 adhesives
will still react, but will take longer. Temperatures above 85 F (18 C and 30 C) will increase cure and
fixture speeds, and there s a risk that the adhesive will be hardened or too thick to bond materials.
The viscosities of BD8110 adhesives are affected by temperature.
NOTE: Because of the curing features of BD8110 adhesives, large amounts of heat are generated
when large masses of material are mixed at one time. The heat generated by the exotherm resulting
from mixing large amounts of adhesive can result in a boiling of the monomer in the adhesive (methyl
methacrylate), resulting in the release of trapped air, steam and volatile gasses. To prevent this, use
only enough material as needed for use within the working time for the product, and confine the gap
or spread out the material to no more than .50 inches.
7. HANDLING AND STORAGE
The shelf life of BD8110 is nine (9) months from the date of manufacture based upon continuous
storage at room temperature (77 F or 25 C). Storage of BD8110 adhesives in refrigerated
compartments will extend the shelf life even more. Do not store BD8110 adhesive or any other
adhesives in a refrigerator which has food or lunch products in them. Be sure to bring BD8110
adhesives to room temperature for 24 hours before use, otherwise longer cure and fixture times may
be expected. Long-term storage at temperatures above room temperature will shorten the shelf life of
BD8110 adhesives considerably. Storage at temperatures above 100 F or 38 C could shorten the
shelf life to less than one month. BD8110 adhesives contain no water, so freezing of the adhesive for
short periods is permissible, but is not encouraged.
8. ADDITIONAL INFORMATION
NOTE: Information contained herein is based on tests we believe to be reliable and accurate. It is
offered in good faith for the benefit of the consumer. The Company shall not be liable for any injury,
loss, or damage in the use or handling of its chemical products since conditions and use are beyond
our control. In every case, we urge and recommend the user conduct tests to determine to their
own satisfaction that the product is of acceptable quality and suitability for their particular purpose
under their own operating conditions. Statements concerning possible use of our products are not
intended as recommendations to use our products in the infringement of any patent, or for any
particular purpose or application. These products are intended for industrial use only.
by | Sep 27, 2025
615 S 4
th
Street, Elkhart, IN 46516-2717 Page 1 of 2
www.bigdogadhesives.com Ph: 833-BIG-DOGG (833-244-3644) July 2018
TECHNICAL DATA SHEET
1. DESCRIPTION
BD590 is a two-part methacrylate, structural bonding adhesive designed for the structural
bonding of various substrates, including fiberglass, steel, aluminum, and various plastics (not
low energy surfaces). Combined at a ratio of 1:1, BD590 has a working time of 70 to 100
minutes and achieves nearly 90 percent of its ultimate strength in 180 to 240 minutes at room
temperature curing. BD590 provides high strength bonds to the above reference surfaces
with generally no preparation effort. BD590 bonds very strongly to steel, stainless steel, and
aluminum metals. BD590 adhesives are NOT UV STABLE, AND WILL YELLOW OVER TIME
and must not be used to create imperceptible seams in countertops or for seaming
countertops. This yellowing will not affect bond performance, but will affect bond appearance.
Company Identification: Big Dog Adhesives LLC.
615 S 4th Street
Elkhart, IN 46516-2717
Toll-free: 833-BIG-DOGG (833-244-3644)
Fax: 833-BIG-DOGZ (833-244-3649)
Website: www.bigdogadhesives.com lou@bigdogadhesives.com
2. CHARACTERISTICS :
Room Temperature Cure Properties
Working Time 70 to 100 minutes (at 75 F/ 24 C)
Fixture Time 180 to 240 minutes (at 75 F/ 24 C)
Can be Moved In 300 minutes
Operating Temp. 65 F to 85 F (18 C to 30 C)
Gap Filling 1.5 inches
Mixed Density 8.1 lbs/gal (.96 g/cc)
Flash Point 51 F (11 C) See SDS for more safety information
3. CHEMICAL RESISTANCE:
Excellent Resistance to: Susceptible to:
Hydrocarbons Polar Solvents
Acids and Bases Super Strong Acids and Bases
Vinegar
Wine and Condiments
Most Household Foods
4. PHYSICAL PROPERTIES:
Uncured: Resin Activator
Viscosity(cps) 130,000 250,000 130,000 250,000
Color Translucent Amber
Density (lbs/gal) 8.2 8.0
Mix Ratio (wt or vol) 1.0 1.0
Mixer Recommendation Cartridge (200/400ml): MFQ 08-24T Square 24 element
White/Green Mix Tips (1:1)
BD590 Structural Methacrylate Adhesive
615 S 4
th
Street, Elkhart, IN 46516-2717 Page 2 of 2
www.bigdogadhesives.com Ph: 833-BIG-DOGG (833-244-3644) July 2018
TECHNICAL DATA SHEET
5. MECHANICAL PROPERTIES:
Tensile Strength (ASTM D638) Substrate Results Failure Type
Strength, psi Acrylic Solid Surface 2,000 – 3,000 Cohesive
Strength, psi Polyester Solid Surface 2,000 3,000 Substrate
Strength, psi Steel/Stainless Steel 1,800 2,500 Cohesive
Strength, psi Aluminum 1,800 2,500 Cohesive
6. HANDLING AND APPLICATION:
BD590 resin (Part A) and activator (Part B) are flammable. Contents include Methacrylate ester and
acids. Keep containers closed after use. Wear gloves and safety glasses to avoid skin and eye
contact. Wash with soap and water after skin contact. In case of eye contact, flush with water for 15
minutes and get medical attention. Harmful if swallowed. Keep out of the reach of children. Keep
away from heat, sparks, and open flames. Do not smoke cigarettes or anything else while handling or
near the product. Refer to the BD590 Safety Data Sheet for more complete safety instruction. To
assure maximum bond strength, surfaces must be mated together within the specified working time,
and all clamps affixed within that time. Use sufficient material to ensure that the joint is completely
filled when parts are mated and clamped. Avoid over clamping parts, which may cause a dry joint or
a joint starved of adhesive. All adhesive application, part positioning, fixturing, and clamping should
occur before the working time of the adhesive has expired. After the indicated working time, parts
must remain undisturbed until the fixture time is completed. Components bonded, adhesive, and
shop temperature can have a significant effect on the work and fixture time of the adhesive.
Application of BD590 adhesive at temperatures between 65 F and 85 F (18 C and 30 C) will ensure
proper cure. Temperatures below 65 F (18 C) will slow cure and fixture speed. BD590 adhesives will
still react, but will take longer. Temperatures above 85 F (18 C and 30 C) will increase cure and
fixture speeds, and there s a risk that the adhesive will be hardened or too thick to bond materials.
The viscosities of BD590 adhesives are affected by temperature.
NOTE: Because of the curing features of BD590 adhesives, large amounts of heat are generated
when large masses of material are mixed at one time. The heat generated by the exotherm resulting
from mixing large amounts of adhesive can result in a boiling of the monomer in the adhesive (methyl
methacrylate), resulting in the release of trapped air, steam and volatile gasses. To prevent this, use
only enough material as needed for use within the working time for the product, and confine the gap
or spread out the material to no more than .50 inches.
7. HANDLING AND STORAGE
The shelf life of BD590 is nine (9) months from the date of manufacture based upon continuous
storage at room temperature (77 F or 25 C). Storage of BD590 adhesives in refrigerated
compartments will extend the shelf life even more. Do not store BD590 adhesive or any other
adhesives in a refrigerator which has food or lunch products in them. Be sure to bring BD590
adhesives to room temperature for 24 hours before use, otherwise longer cure and fixture times may
be expected. Long-term storage at temperatures above room temperature will shorten the shelf life of
BD590 adhesives considerably. Storage at temperatures above 100 F or 38 C could shorten the
shelf life to less than one month. BD590 adhesives contain no water, so freezing of the adhesive for
short periods is permissible, but is not encouraged.
8. ADDITIONAL INFORMATION
NOTE: Information contained herein is based on tests we believe to be reliable and accurate. It is
offered in good faith for the benefit of the consumer. The Company shall not be liable for any injury,
loss, or damage in the use or handling of its chemical products since conditions and use are beyond
our control. In every case, we urge and recommend the user conduct tests to determine to their
own satisfaction that the product is of acceptable quality and suitability for their particular purpose
under their own operating conditions. Statements concerning possible use of our products are not
intended as recommendations to use our products in the infringement of any patent, or for any
particular purpose or application. These products are intended for industrial use only.
by | Sep 27, 2025
435 Harrison Street, Elkhart, IN 46516-2717 Page 1 of 1
www.bigdogadhesives.com Ph: 833-BIG-DOGG (833-244-3644) September 2024
TECHNICAL DATA SHEET
1. DESCRIPTION:
BD54460 is a two-part, epoxy room
temperature cure adhesive designed for
industrial bonding, small potting and
laminating where excellent strength and
toughness, structural bonding, and
mechanical and electrical properties are
required. This 2-part adhesive cures at
room temperature, exhibits good wetting,
and develops high strength with low
shrinkage. Bonds to most materials
including fiberglass, ceramics, metals and
many plastics. It has great dimensional
stability over a wide range of temperatures.
Fully cured BD54460 is a durable electrical
insulator with resistance to water, weather,
ozone and oxygen, various solvents, fuels,
oils, alcohols, mild acids and alkalis and
many other organic compounds including
diesel fuel and gasoline. It is especially
formulated for a 2:1 mix ratio for use in side
by side cartridges, or to be used by hand
mixing, or use with Meter Mix Equipment.
A handling cure is normally achieved at
room temperature within 120 minutes with
a full cure at room temperature within 24
hours. To accelerate the final cure, or to
quicken the handling simply elevate the
temperature.
2. CHARACTERISTICS:
Room Temperature Cure Properties
Work Time: 50 to 60 minutes (at 75 F/ 24 C)
Fixture Time: 2 to 4 hours (at 75 F/ 24 C)
Full Cure: 24 to 48 hours for full properties
Operating Temp. -60 F(-76 C ) to 302 F (150 C)
Mixed Density: 9.5 lbs/gal (1.15 g/cc)
Flash Point: Greater than 200 C (392 F)
Viscosity: Resin (Part A) 40,000 CPS
Hard (Part B) 10,000 CPS
Color: Resin (Part A) Off-White, white or
Black
Activator (Part B) Amber
Mixed: Off-White, white, or Black
Mix Ratio: 2 Part A to 1 Part B (2:1)
Hardness: 75 – 80 Shore D
Lap Shear Strength: > 4,000 psi (AL to AL)
Tensile Strength: 6,600 psi
Elongation: 2.5%
Impact Resistance: > 150 inch/lb
Water Absorption: < 1% (24 hours)
Dielectric Constant 4.5 (at 25C, 100Hz)
Dielectric Strength 1,100 v/mil
Volume Resistivity 2.4 x 10
14
ohm-cm
Shelf Life: 12 Months
VOC Content: 0% by weight
3. Handling and Storage:
A. Bring both components to room temperature prior to
mixing. Mix 2 parts A to 1 part B by volume or 213
grams part a to 100 grams part B by weight
thoroughly for 30 to 60 seconds.
B. Dispense mixed material over properly positioned
devices to be glued together.
C. Parts may be shipped within 48 hours but parts can
be moved in 4 hours.
4. ADDITIONAL INFORMATION
NOTE: Information contained herein is
based on tests we believe to be reliable and
accurate. It is offered in good faith for the
benefit of the consumer. The Company shall
not be liable for any injury, loss, or damage in
the use or handling of its chemical products
since conditions and use are beyond our
control. In every case, we urge and
recommend the user conduct tests to
determine to their own satisfaction that the
product is of acceptable quality and suitability
for their particular purpose under their own
operating conditions. Statements concerning
possible use of our products are not intended
as recommendations to use our products in
the infringement of any patent, or for any
particular purpose or application. These
products are intended for industrial use only.
BD54460 Epoxy Adhesive
by | Sep 27, 2025
615 S 4
th
Street, Elkhart, IN 46516-2717 Page 1 of 1
www.bigdogadhesives.com Ph: 833-BIG-DOGG (833-244-3644) December 2018
TECHNICAL DATA SHEET
1. DESCRIPTION:
BD5430 is a two-part, unfilled room
temperature cure, epoxy adhesive designed
for bonding of metals, ceramics, and most
plastics. It cures to a tough semi-rigid
material, and is free flowing in viscosity. It
gives good resistance to water, salt spray,
inorganic acids and bases, and most
organic solvents. It is especially
formulated for a 1:1 mix ratio for use in side
by side cartridges, or to be used by hand
mixing, or use with Meter Mix Equipment.
A handling cure is normally achieved at
room temperature within 240 minutes with
a full cure at room temperature within 24
hours. To accelerate the final cure, or to
quicken the handling simply elevate the
temperature.
2. CHARACTERISTICS :
Room Temperature Cure Properties
Work Time: 30 to 40 minutes (at 75 F/ 24 C)
Fixture Time: 4 hours (at 75 F/ 24 C)
Full Cure: 24 to 48 hours for full properties
Operating Temp. -40 F(-40 C ) to 302 F (150 C)
Mixed Density: 9.5 lbs/gal (1.15 g/cc)
Flash Point: Greater than 200 C (392 F)
Viscosity: Resin (Part A) 7,000 CPS
Hard (Part B) 5,000 CPS
Color: Resin (Part A) Clear
Activator (Part B) Clear
Mixed: Clear
Mix Ratio: 1 Part A to 1 Part B (1:1)
Hardness: 70 Shore D
Lap Shear Strength: > 2,300 PSI (AL to AL)
Tensile Strength: 6,500 PSI
Elongation: 5% to 10%
Impact Resistance: > 150 inch/lb
Water Absorption: < 1% (24 hours)
Dielectric Constant 6.3 (at 25C, 100Hz)
Dielectric Strength 680 v/mil
Volume Resistivity 1 x 10
11
ohm-cm
Shelf Life: 12 Months
VOC Content: 0% by weight
3. Handling and Storage:
A. Bring both components to room temperature prior to
mixing. Mix 1 part A to 1 part B thoroughly for 30 to
60 seconds.
B. Dispense mixed material over properly positioned
devices to be glued together. Do not pour more than
1/2 thick as the product may exotherm too high and
may boil. As this is a very quick adhesive, you must
work quickly to bond the pieces together.
C. Parts may be shipped within 24 hours but parts can
be moved in 1 hour.
4. ADDITIONAL INFORMATION
NOTE: Information contained herein is
based on tests we believe to be reliable and
accurate. It is offered in good faith for the
benefit of the consumer. The Company shall
not be liable for any injury, loss, or damage in
the use or handling of its chemical products
since conditions and use are beyond our
control. In every case, we urge and
recommend the user conduct tests to
determine to their own satisfaction that the
product is of acceptable quality and suitability
for their particular purpose under their own
operating conditions. Statements concerning
possible use of our products are not intended
as recommendations to use our products in
the infringement of any patent, or for any
particular purpose or application. These
products are intended for industrial use only.
BD5430 Epoxy Adhesive
by | Sep 27, 2025
615 S 4
th
Street, Elkhart, IN 46516-2717 Page 1 of 1
www.bigdogadhesives.com Ph: 833-BIG-DOGG (833-244-3644) December 2018
TECHNICAL DATA SHEET
1. DESCRIPTION:
BD5410 is a two-part, unfilled room
temperature cure, epoxy adhesive designed
for high speed bonding of metals,
ceramics, and most plastics. It cures to a
tough semi-rigid material, and is free
flowing in viscosity. It gives good
resistance to water, salt spray, inorganic
acids and bases, and most organic
solvents. It is especially formulated for a
1:1 mix ratio for use in side by side
cartridges, or to be used by hand mixing, or
use with Meter Mix Equipment.
A handling cure is normally achieved at
room temperature within 60 minutes with a
full cure at room temperature within 24
hours. To accelerate the final cure, or to
quicken the handling simply elevate the
temperature.
2. CHARACTERISTICS :
Room Temperature Cure Properties
Work Time: 8 to 12 minutes (at 75 F/ 24 C)
Fixture Time: 60 minutes (at 75 F/ 24 C)
Full Cure: 24 hours for full properties
Operating Temp. -40 F(-40 C ) to 266 F (130 C)
Mixed Density: 9.5 lbs/gal (1.15 g/cc)
Flash Point: Greater than 200 C (392 F)
Viscosity: Resin (Part A) 12,000 CPS
Hard (Part B) 20,000 CPS
Color: Resin (Part A) Clear
Activator (Part B) Clear
Mixed: Clear
Mix Ratio: 1 Part A to 1 Part B (1:1)
Hardness: 80 Shore D
Lap Shear Strength: > 2,300 PSI (AL to AL)
Tensile Strength: 6,500 PSI
Elongation: 5% to 10%
Impact Resistance: > 150 inch/lb
Water Absorption: < 1% (24 hours)
Dielectric Constant 4.5 (at 25C, 100Hz)
Dielectric Strength 410 v/mil
Volume Resistivity 8 x 10
14
ohm-cm
Shelf Life: 12 Months
VOC Content: 0% by weight
3. Handling and Storage:
A. Bring both components to room temperature prior to
mixing. Mix 1 part A to 1 part B thoroughly for 30 to
60 seconds.
B. Dispense mixed material over properly positioned
devices to be glued together. Do not pour more than
1/2 thick as the product may exotherm too high and
may boil. As this is a very quick adhesive, you must
work quickly to bond the pieces together.
C. Parts may be shipped within 24 hours but parts can
be moved in 1 hour.
4. ADDITIONAL INFORMATION
NOTE: Information contained herein is
based on tests we believe to be reliable and
accurate. It is offered in good faith for the
benefit of the consumer. The Company shall
not be liable for any injury, loss, or damage in
the use or handling of its chemical products
since conditions and use are beyond our
control. In every case, we urge and
recommend the user conduct tests to
determine to their own satisfaction that the
product is of acceptable quality and suitability
for their particular purpose under their own
operating conditions. Statements concerning
possible use of our products are not intended
as recommendations to use our products in
the infringement of any patent, or for any
particular purpose or application. These
products are intended for industrial use only.
BD5410 Epoxy Adhesive
by | Sep 27, 2025
435 Harrison Street, Elkhart, IN 46516-2717 Page 1 of 1
www.bigdogadhesives.com Ph: 833-BIG-DOGG (833-244-3644) September 2024
TECHNICAL DATA SHEET
1. DESCRIPTION:
BD5405NS is a non-sag, two-part, unfilled,
room temperature cure, epoxy adhesive
designed for high speed bonding of metals,
ceramics, and most plastics. It cures to a
tough semi-rigid material. It gives good
resistance to water, salt spray, inorganic
acids and bases, and most organic
solvents. It is especially formulated for a
1:1 mix ratio for use in side by side
cartridges, or to be used by hand mixing, or
use with Meter Mix Equipment.
A handling cure is normally achieved at
room temperature within 20 30 minutes
with a full cure at room temperature within
24 hours. To accelerate the final cure, or to
quicken the handling simply elevate the
temperature.
2. CHARACTERISTICS:
Room Temperature Cure Properties
Work Time: 3 to 5 minutes (at 75 F/ 24 C)
Fixture Time: 20 to 20 minutes (at 75 F/ 24 C)
Full Cure: 24 hours for full properties
Operating Temp. -40 F(-40 C ) to 266 F (130 C)
Mixed Density: 9.5 lbs/gal (1.15 g/cc)
Flash Point: Greater than 200 C (392 F)
Viscosity: Resin (Part A) 180,000 CPS
Hard (Part B) 150,000 CPS
Color: Resin (Part A) Clear or Black
Activator (Part B) Clear
Mixed: Clear or Black
Mix Ratio: 1 Part A to 1 Part B (1:1)
Hardness: 58 Shore D
Lap Shear Strength: > 2,300 PSI (AL to AL)
Tensile Strength: 6,500 PSI
Elongation: 5% to 10%
Impact Resistance: > 150 inch/lb
Water Absorption: < 1% (24 hours)
Dielectric Constant 4.5 (at 25C, 100Hz)
Dielectric Strength 410 v/mil
Volume Resistivity 8 x 10
14
ohm-cm
Shelf Life: 12 Months
VOC Content: 0% by weight
3. Handling and Storage:
A. Bring both components to room temperature prior to
mixing. Mix 1 part A to 1 part B thoroughly for 30 to
60 seconds.
B. Dispense mixed material over properly positioned
devices to be glued together. Do not pour more than
1/2 thick as the product may exotherm too high and
may boil. As this is a very quick adhesive, you must
work quickly to bond the pieces together.
C. Parts may be shipped within 24 hours but parts can
be moved in 1 hour.
4. ADDITIONAL INFORMATION
NOTE: Information contained herein is
based on tests we believe to be reliable and
accurate. It is offered in good faith for the
benefit of the consumer. The Company shall
not be liable for any injury, loss, or damage in
the use or handling of its chemical products
since conditions and use are beyond our
control. In every case, we urge and
recommend the user conduct tests to
determine to their own satisfaction that the
product is of acceptable quality and suitability
for their particular purpose under their own
operating conditions. Statements concerning
possible use of our products are not intended
as recommendations to use our products in
the infringement of any patent, or for any
particular purpose or application. These
products are intended for industrial use only.
BD5405NS Epoxy Adhesive
by | Sep 27, 2025
435 Harrison Street, Elkhart, IN 46516-2717 Page 1 of 2
www.bigdogadhesives.com Ph: 833-BIG-DOGG (833-244-3644) Sept. 2018
TECHNICAL DATA SHEET
1. DESCRIPTION
BD530 is a two-part methacrylate, structural bonding adhesive designed for the structural
bonding of various substrates, including fiberglass, steel, aluminum, and various plastics.
Combined at a ratio of 1:1, BD530 has a working time of 25 to 40 minutes and achieves nearly
90 percent of its ultimate strength in 90 to 150 minutes at room temperature curing. BD530
provides high strength bonds to the above reference surfaces with generally no preparation
effort. BD530 bonds very strongly to steel, stainless steel, and aluminum metals.
countertops. BD530 comes with excellent toughness and high impact strength.
Company Identification: Big Dog Adhesives LLC.
435 Harrison Street
Elkhart, IN 46516-2717
Toll-free: 833-BIG-DOGG (833-244-3644)
Fax: 833-BIG-DOGZ (833-244-3649)
Website: www.bigdogadhesives.com lou@bigdogadhesives.com
2. CHARACTERISTICS :
Room Temperature Cure Properties
Working Time 25 to 40 minutes (at 75 F/ 24 C)
Fixture Time 70 to 150 minutes (at 75 F/ 24 C)
Can be Moved In 180 minutes
Operating Temp. -40F F to 180 F (-40 C to 82 C)
Gap Filling .75 inches
Mixed Density 8.1 lbs/gal (.96 g/cc)
Flash Point 51 F (11 C) See SDS for more safety information
3. CHEMICAL RESISTANCE:
Excellent Resistance to: Susceptible to:
Hydrocarbons Polar Solvents
Acids and Bases Super Strong Acids and Bases
Vinegar
Wine and Condiments
Most Household Foods
4. PHYSICAL PROPERTIES:
Uncured: Resin Activator
Viscosity(cps) 130,000 250,000 130,000 250,000
Color Translucent Amber/Black/White
Density (lbs/gal) 8.2 8.0
Mix Ratio (wt or vol) 1.0 1.0
Mixer Recommendation Cartridge (200/400ml): MFQ 08-24T Square 24 element
White/Green Mix Tips (1:1)
5. MECHANICAL PROPERTIES:
BD530 Structural Methacrylate Adhesive
435 Harrison Street, Elkhart, IN 46516-2717 Page 2 of 2
www.bigdogadhesives.com Ph: 833-BIG-DOGG (833-244-3644) Sept. 2018
TECHNICAL DATA SHEET
Tensile Strength (ASTM D638) Substrate Results Failure Type
Strength, psi ABS 1000 — 1500 Cohesive
Strength, psi Steel/Stainless Steel 1,800 2,500 Cohesive
Strength, psi Aluminum 1,800 2,500 Cohesive
6. HANDLING AND APPLICATION:
BD530 resin (Part A) and activator (Part B) are flammable. Contents include Methacrylate ester and
acids. Keep containers closed after use. Wear gloves and safety glasses to avoid skin and eye
contact. Wash with soap and water after skin contact. In case of eye contact, flush with water for 15
minutes and get medical attention. Harmful if swallowed. Keep out of the reach of children. Keep
away from heat, sparks, and open flames. Do not smoke cigarettes or anything else while handling or
near the product. Refer to the BD530 Safety Data Sheet for more complete safety instruction. To
assure maximum bond strength, surfaces must be mated together within the specified working time,
and all clamps affixed within that time. Use sufficient material to ensure that the joint is completely
filled when parts are mated and clamped. Avoid over clamping parts, which may cause a dry joint or
a joint starved of adhesive. All adhesive application, part positioning, fixturing, and clamping should
occur before the working time of the adhesive has expired. After the indicated working time, parts
must remain undisturbed until the fixture time is completed. Components bonded, adhesive, and
shop temperature can have a significant effect on the work and fixture time of the adhesive.
Application of BD530 adhesive at temperatures between 65 F and 85 F (18 C and 30 C) will ensure
proper cure. Temperatures below 65 F (18 C) will slow cure and fixture speed. BD530 adhesives will
still react, but will take longer. Temperatures above 85 F (18 C and 30 C) will increase cure and
fixture speeds, and there s a risk that the adhesive will be hardened or too thick to bond materials.
The viscosities of BD530 adhesives are affected by temperature.
NOTE: Because of the curing features of BD530 adhesives, large amounts of heat are generated
when large masses of material are mixed at one time. The heat generated by the exotherm resulting
from mixing large amounts of adhesive can result in a boiling of the monomer in the adhesive (methyl
methacrylate), resulting in the release of trapped air, steam and volatile gasses. To prevent this, use
only enough material as needed for use within the working time for the product, and confine the gap
or spread out the material to no more than .50 inches.
7. HANDLING AND STORAGE
The shelf life of BD530 is nine (9) months from the date of manufacture based upon continuous
storage at room temperature (77 F or 25 C). Storage of BD530 adhesives in refrigerated
compartments will extend the shelf life even more. Do not store BD530 adhesive or any other
adhesives in a refrigerator which has food or lunch products in them. Be sure to bring BD530
adhesives to room temperature for 24 hours before use, otherwise longer cure and fixture times may
be expected. Long-term storage at temperatures above room temperature will shorten the shelf life of
BD530 adhesives considerably. Storage at temperatures above 100 F or 38 C could shorten the
shelf life to less than one month. BD530 adhesives contain no water, so freezing of the adhesive for
short periods is permissible, but is not encouraged.
8. ADDITIONAL INFORMATION
NOTE: Information contained herein is based on tests we believe to be reliable and accurate. It is
offered in good faith for the benefit of the consumer. The Company shall not be liable for any injury,
loss, or damage in the use or handling of its chemical products since conditions and use are beyond
our control. In every case, we urge and recommend the user conduct tests to determine to their
own satisfaction that the product is of acceptable quality and suitability for their particular purpose
under their own operating conditions. Statements concerning possible use of our products are not
intended as recommendations to use our products in the infringement of any patent, or for any
particular purpose or application. These products are intended for industrial use only.
by | Sep 27, 2025
435 Harrison Street, Elkhart, IN 46516-2717 Page 1 of 3
www.bigdogadhesives.com Ph: 833-BIG-DOGG (833-244-3644) January 2023
TECHNICAL DATA SHEET
1. DESCRIPTION
BD420FX is a two-part methacrylate, flexibilized, structural bonding adhesive designed for the
structural bonding of various substrates, including fiberglass, steel, aluminum, and various
plastics (not low energy surfaces). Combined at a ratio of 10:1, BD420FX has a working time
of 3 to 7 minutes and achieves nearly 90 percent of its ultimate strength in 10 to 15 minutes at
room temperature curing. BD420FX provides high strength and very flexible bonds to the
above reference surfaces with generally no preparation effort. BD420FX bonds very strongly
to steel, stainless steel, and aluminum metals and will allow a great deal of movement of the
substrates due to CTE (Coefficient of Thermal Expansion) differences. BD420FX adhesives
are NOT UV STABLE, AND WILL YELLOW OVER TIME and must not be used to create
imperceptible seams in countertops or for seaming countertops. This yellowing will not affect
bond performance, but will affect bond appearance.
Company Identification: Big Dog Adhesives LLC.
615 S 4th Street
Elkhart, IN 46516-2717
Toll-free: 833-BIG-DOGG (833-244-3644)
Fax: 833-BIG-DOGZ (833-244-3649)
Website: www.bigdogadhesives.com lou@bigdogadhesives.com
2. CHARACTERISTICS :
Room Temperature Cure Properties
Working Time 3 to 7 minutes (at 75 F/ 24 C)
Fixture Time 10 to 15 minutes (at 75 F/ 24 C)
Can be Moved In 15 to 20 minutes
Operating Temp. 65 F to 85 F (18 C to 30 C)
Gap Filling .375 inches (3/8 )
Mixed Density 8.1 lbs/gal (.96 g/cc)
Elongation: Greater than 100%
Flash Point 51 F (11 C) See SDS for more safety information
Operating Temp. -30 F to 130 F
3. CHEMICAL RESISTANCE:
Excellent Resistance to: Susceptible to:
Hydrocarbons Polar Solvents
Acids and Bases Super Strong Acids and Bases
Vinegar
Wine and Condiments
Most Household Foods
4. PHYSICAL PROPERTIES:
Uncured: Resin Activator
Viscosity(cps) 150,000 200,000 50,000 100,000
Color Amber White, various colors
Density (lbs/gal) 8.2 8.5
Mix Ratio (wt or vol) 10 1.0
Mixer Recommendation Cartridge (250/490ml): MFQX 08-24T Square 24 element
Orange/Green Mix Tips (10:1)
BD420FX Structural Methacrylate Adhesive
435 Harrison Street, Elkhart, IN 46516-2717 Page 2 of 3
www.bigdogadhesives.com Ph: 833-BIG-DOGG (833-244-3644) January 2023
TECHNICAL DATA SHEET
5. MECHANICAL PROPERTIES:
Tensile Strength (ASTM D638) Substrate Results Failure Type
Strength, psi Fiberglass Surfaces 2,500+ Substrate
Strength, psi ABS/PVC Sheeting 1,000+ Substrate
Strength, psi Steel/Stainless Steel 2,500 3,500 Cohesive
Strength, psi Aluminum 2,500 3,500 Cohesive
6. HANDLING AND APPLICATION:
BD420FX resin (Part A) and activator (Part B) are flammable. Contents include Methacrylate ester
and acids. Keep containers closed after use. Wear gloves and safety glasses to avoid skin and eye
contact. Wash with soap and water after skin contact. In case of eye contact, flush with water for 15
minutes and get medical attention. Harmful if swallowed. Keep out of the reach of children. Keep
away from heat, sparks, and open flames. Do not smoke cigarettes or anything else while handling or
near the product. Refer to the BD420FX Safety Data Sheet for more complete safety instruction. To
assure maximum bond strength, surfaces must be mated together within the specified working time,
and all clamps affixed within that time. Use sufficient material to ensure that the joint is completely
filled when parts are mated and clamped. Avoid over clamping parts, which may cause a dry joint or
a joint starved of adhesive. All adhesive application, part positioning, fixturing, and clamping should
occur before the working time of the adhesive has expired. After the indicated working time, parts
must remain undisturbed until the fixture time is completed. Components bonded, adhesive, and
shop temperature can have a significant effect on the work and fixture time of the adhesive.
Application of BD420FX adhesive at temperatures between 65 F and 85 F (18 C and 30 C) will
ensure proper cure. Temperatures below 65 F (18 C) will slow cure and fixture speed. BD420FX
adhesives will still react, but will take longer. Temperatures above 85 F (18 C and 30 C) will increase
cure and fixture speeds, and there s a risk that the adhesive will be hardened or too thick to bond
materials. The viscosities of BD420FX adhesives are affected by temperature.
NOTE: Because of the curing features of BD420FX adhesives, large amounts of heat are generated
when large masses of material are mixed at one time. The heat generated by the exotherm resulting
from mixing large amounts of adhesive can result in a boiling of the monomer in the adhesive (methyl
methacrylate), resulting in the release of trapped air, steam and volatile gasses. To prevent this, use
only enough material as needed for use within the working time for the product, and confine the gap
or spread out the material to no more than .50 inches.
7. HANDLING AND STORAGE
The shelf life of BD420FX is twelve (12) months from the date of manufacture based upon continuous
storage at room temperature (77 F or 25 C). Storage of BD420FX adhesives in refrigerated
compartments will extend the shelf life even more. Do not store BD420FX adhesive or any other
adhesives in a refrigerator which has food or lunch products in them. Be sure to bring BD420FX
adhesives to room temperature for 24 hours before use, otherwise longer cure and fixture times may
be expected. Long-term storage at temperatures above room temperature will shorten the shelf life of
BD420FX adhesives considerably. Storage at temperatures above 100 F or 38 C could shorten the
shelf life to less than one month. BD420FX adhesives contain no water, so freezing of the adhesive
for short periods is permissible, but is not encouraged.
8. ADDITIONAL INFORMATION
NOTE: Information contained herein is based on tests we believe to be reliable and accurate. It is
offered in good faith for the benefit of the consumer. The Company shall not be liable for any injury,
loss, or damage in the use or handling of its chemical products since conditions and use are beyond
our control. In every case, we urge and recommend the user conduct tests to determine to their
own satisfaction that the product is of acceptable quality and suitability for their particular purpose
under their own operating conditions. Statements concerning possible use of our products are not
435 Harrison Street, Elkhart, IN 46516-2717 Page 3 of 3
www.bigdogadhesives.com Ph: 833-BIG-DOGG (833-244-3644) January 2023
TECHNICAL DATA SHEET
intended as recommendations to use our products in the infringement of any patent, or for any
particular purpose or application. These products are intended for industrial use only.
by | Sep 27, 2025
435 Harrison Street, Elkhart, IN 46516-2717 Page 1 of 3
www.bigdogadhesives.com Ph: 833-BIG-DOGG (833-244-3644) January 2023
TECHNICAL DATA SHEET
1. DESCRIPTION
BD420FX is a two-part methacrylate, flexibilized, structural bonding adhesive designed for the
structural bonding of various substrates, including fiberglass, steel, aluminum, and various
plastics (not low energy surfaces). Combined at a ratio of 10:1, BD420FX has a working time
of 3 to 7 minutes and achieves nearly 90 percent of its ultimate strength in 10 to 15 minutes at
room temperature curing. BD420FX provides high strength and very flexible bonds to the
above reference surfaces with generally no preparation effort. BD420FX bonds very strongly
to steel, stainless steel, and aluminum metals and will allow a great deal of movement of the
substrates due to CTE (Coefficient of Thermal Expansion) differences. BD420FX adhesives
are NOT UV STABLE, AND WILL YELLOW OVER TIME and must not be used to create
imperceptible seams in countertops or for seaming countertops. This yellowing will not affect
bond performance, but will affect bond appearance.
Company Identification: Big Dog Adhesives LLC.
615 S 4th Street
Elkhart, IN 46516-2717
Toll-free: 833-BIG-DOGG (833-244-3644)
Fax: 833-BIG-DOGZ (833-244-3649)
Website: www.bigdogadhesives.com lou@bigdogadhesives.com
2. CHARACTERISTICS :
Room Temperature Cure Properties
Working Time 3 to 7 minutes (at 75 F/ 24 C)
Fixture Time 10 to 15 minutes (at 75 F/ 24 C)
Can be Moved In 15 to 20 minutes
Operating Temp. 65 F to 85 F (18 C to 30 C)
Gap Filling .375 inches (3/8 )
Mixed Density 8.1 lbs/gal (.96 g/cc)
Elongation: Greater than 100%
Flash Point 51 F (11 C) See SDS for more safety information
Operating Temp. -30 F to 130 F
3. CHEMICAL RESISTANCE:
Excellent Resistance to: Susceptible to:
Hydrocarbons Polar Solvents
Acids and Bases Super Strong Acids and Bases
Vinegar
Wine and Condiments
Most Household Foods
4. PHYSICAL PROPERTIES:
Uncured: Resin Activator
Viscosity(cps) 150,000 200,000 50,000 100,000
Color Amber White, various colors
Density (lbs/gal) 8.2 8.5
Mix Ratio (wt or vol) 10 1.0
Mixer Recommendation Cartridge (250/490ml): MFQX 08-24T Square 24 element
Orange/Green Mix Tips (10:1)
BD420FX Structural Methacrylate Adhesive
435 Harrison Street, Elkhart, IN 46516-2717 Page 2 of 3
www.bigdogadhesives.com Ph: 833-BIG-DOGG (833-244-3644) January 2023
TECHNICAL DATA SHEET
5. MECHANICAL PROPERTIES:
Tensile Strength (ASTM D638) Substrate Results Failure Type
Strength, psi Fiberglass Surfaces 2,500+ Substrate
Strength, psi ABS/PVC Sheeting 1,000+ Substrate
Strength, psi Steel/Stainless Steel 2,500 3,500 Cohesive
Strength, psi Aluminum 2,500 3,500 Cohesive
6. HANDLING AND APPLICATION:
BD420FX resin (Part A) and activator (Part B) are flammable. Contents include Methacrylate ester
and acids. Keep containers closed after use. Wear gloves and safety glasses to avoid skin and eye
contact. Wash with soap and water after skin contact. In case of eye contact, flush with water for 15
minutes and get medical attention. Harmful if swallowed. Keep out of the reach of children. Keep
away from heat, sparks, and open flames. Do not smoke cigarettes or anything else while handling or
near the product. Refer to the BD420FX Safety Data Sheet for more complete safety instruction. To
assure maximum bond strength, surfaces must be mated together within the specified working time,
and all clamps affixed within that time. Use sufficient material to ensure that the joint is completely
filled when parts are mated and clamped. Avoid over clamping parts, which may cause a dry joint or
a joint starved of adhesive. All adhesive application, part positioning, fixturing, and clamping should
occur before the working time of the adhesive has expired. After the indicated working time, parts
must remain undisturbed until the fixture time is completed. Components bonded, adhesive, and
shop temperature can have a significant effect on the work and fixture time of the adhesive.
Application of BD420FX adhesive at temperatures between 65 F and 85 F (18 C and 30 C) will
ensure proper cure. Temperatures below 65 F (18 C) will slow cure and fixture speed. BD420FX
adhesives will still react, but will take longer. Temperatures above 85 F (18 C and 30 C) will increase
cure and fixture speeds, and there s a risk that the adhesive will be hardened or too thick to bond
materials. The viscosities of BD420FX adhesives are affected by temperature.
NOTE: Because of the curing features of BD420FX adhesives, large amounts of heat are generated
when large masses of material are mixed at one time. The heat generated by the exotherm resulting
from mixing large amounts of adhesive can result in a boiling of the monomer in the adhesive (methyl
methacrylate), resulting in the release of trapped air, steam and volatile gasses. To prevent this, use
only enough material as needed for use within the working time for the product, and confine the gap
or spread out the material to no more than .50 inches.
7. HANDLING AND STORAGE
The shelf life of BD420FX is twelve (12) months from the date of manufacture based upon continuous
storage at room temperature (77 F or 25 C). Storage of BD420FX adhesives in refrigerated
compartments will extend the shelf life even more. Do not store BD420FX adhesive or any other
adhesives in a refrigerator which has food or lunch products in them. Be sure to bring BD420FX
adhesives to room temperature for 24 hours before use, otherwise longer cure and fixture times may
be expected. Long-term storage at temperatures above room temperature will shorten the shelf life of
BD420FX adhesives considerably. Storage at temperatures above 100 F or 38 C could shorten the
shelf life to less than one month. BD420FX adhesives contain no water, so freezing of the adhesive
for short periods is permissible, but is not encouraged.
8. ADDITIONAL INFORMATION
NOTE: Information contained herein is based on tests we believe to be reliable and accurate. It is
offered in good faith for the benefit of the consumer. The Company shall not be liable for any injury,
loss, or damage in the use or handling of its chemical products since conditions and use are beyond
our control. In every case, we urge and recommend the user conduct tests to determine to their
own satisfaction that the product is of acceptable quality and suitability for their particular purpose
under their own operating conditions. Statements concerning possible use of our products are not
435 Harrison Street, Elkhart, IN 46516-2717 Page 3 of 3
www.bigdogadhesives.com Ph: 833-BIG-DOGG (833-244-3644) January 2023
TECHNICAL DATA SHEET
intended as recommendations to use our products in the infringement of any patent, or for any
particular purpose or application. These products are intended for industrial use only.
