by | Sep 27, 2025
POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363
info@polycoatusa.com | www.polycoatusa.com
TECHNICAL DATA SHEET
PC 561-70A-M5-5M-NAT Product Description
PC 561-70A-M5 is a two-component, 100% solid
Elastomeric Urethane system designed for processing
by either hand mix or typical polyurethane dispensing
equipment.
Recommended Uses
Recommended uses include; Automotive parts, air-
filters, sporting goods, tooling, or applications where
superior tensile strength, elongation, and high-resilience
are required with a Shore A hardness of 68-72A.
Storage and Handling
Containers for both Side-A and Side-B components
should be kept tightly closed to prevent moisture
contamination. Do not reseal if contamination is
suspected. Use of a dry nitrogen blanket for partial
drums is recommended. Side-B may be stored at
ambient temperatures. Storage for Side-A should be
maintained between 77 F (25 C) and 95 F (35 C). For
best results, this product should not be allowed to
freeze, although it may be re-heated in a well ventilated
oven for a period of time to re-liquefy solid particles. To
avoid product degradation, product temperature during
re-heating should not exceed 140 F (60 C). An additional
note of caution is that exposure to temperatures over
400 F (204 C) can create excessive pressure potentially
causing containers to rupture. Do not breathe aerosol or
vapors and avoid contact with skin and eyes. Exposure
to vapors of heated MDI can be dangerous. To heat
product properly, use well ventilated convection ovens
or other methods that distribute heat evenly. Avoid
using drum heaters or other heat sources that may
cause excessive local heating.
Health and Safety
Appropriate literature has been assembled which
provides information concerning the health and safety
precautions that must be observed when handling any
of the products listed above. Before working with these
products, it is your responsibility to read and become
familiar with the available information on its hazards,
proper use and handling. This is extremely important
and cannot be overemphasized. Information is available
in several forms, e.g. material safety data sheets and
product labels. To obtain this information, contact your
Polycoat Products representative.
Typical Properties Side-A (ISO)
NCO 18.9-19.2%
Viscosity @ 77 F (25 C) 500-1100 cps
Specific Gravity @ 77 F (25 C) 1.21
Appearance @ 77 F (25 C) liquid
Typical Properties Side-B (polyol blend)
Viscosity @ 77 F (25 C) 700-900 cps
Specific Gravity @ 77 F (25 C) 1.02
Appearance @ 77 F (25 C) viscous liquid
Typical Physical Properties
Hardness, Shore A 68-72
Resilience, % Rebound 50
Split Tear Strength N/A
Tear Strength, Die C 200-250 pli
(35.1-43.8 kNm)
Tensile Strength 1300-1500 psi
(8.96-10.3 MPa)
Ultimate Elongation 350-400%
Processing Characteristics
Mix Ratio by Weight A:B 62:100
Side-A temperature 90-100 F
(32-38 C)
Side-B temperature 80-100 F
(27-38 C)
Mold temperature 90-120 F
(32-49 C)
Gel Time* @ 74 F (23 C) 4.5-5.5 minutes
Service Temperature -20 F to +180 F
(-29 C to +82 C)
*Variety of gel times available
– H A = O A N A = @ = H H E J B K N I = P E K J E J P D A $ A J A N = H $ Q E @ A H E J A O 1 A ? D J E ? = H ! = P = 0 D A A P O $ Q E @ A 0 L A ? E B ? = P E K J O = J @ 0 = B A P U ! = P = 0 D A A P O 0 ! 0 > A B K N A = L L H U E J C I = P A N E = H 1 D A O A L N K @ Q ? P O = N A B K N
L N K B A O O E K J = H Q O A K J H U = J @ L N A B A N = > H U = L L H E A @ > U L N K B A O O E K J = H O S D K D = R A L N E K N A T L A N E A J ? A S E P D P D A – K H U ? K = P – N K @ Q ? P O I = P A N E = H O K N D = R A Q J @ A N C K J A P N = E J E J C E J = L L H E ? = P E K J K B – K H U ? K = P – N K @ Q ? P O
I = P A N E = H O – Q > H E O D A @ P A ? D J E ? = H @ = P = = J @ E J O P N Q ? P E K J O = N A O Q > F A ? P P K ? D = J C A S E P D K Q P J K P E ? A K J P = ? P U K Q N H K ? = H – K H U ? K = P – N K @ Q ? P O N A L N A O A J P = P E R A K N R E O E P K Q N S A > O E P A B K N ? Q N N A J P P A ? D J E ? = H @ = P =
E J O P N Q ? P E K J O = J @ L N K F A ? P O L A ? E B ? N A ? K I I A J @ = P E K J O
Limited Warranty: – K H U ? K = P – N K @ Q ? P O S = N N = J P O E P O L N K @ Q ? P O P K > A B N A A K B I = J Q B = ? P Q N E J C @ A B A ? P O = J @ P D = P P D A U S E H H I A A P – K H U ? K = P – N K @ Q ? P O ? Q N N A J P L Q > H E O D A @ L D U O E ? = H L N K L A N P E A O 0 A H H A N O
= J @ I = J Q B = ? P Q N A N O O K H A N A O L K J O E > E H E P U O D = H H > A P K N A L H = ? A P D = P L K N P E K J K B P D A L N K @ Q ? P S D E ? D L N K R A O P K > A @ A B A ? P E R A 1 D A N A = N A J K K P D A N S = N N = J P E A O > U – K H U ? K = P – N K @ Q ? P O K B = J U J = P Q N A
S D = P O K A R A N A T L N A O O A @ K N E I L H E A @ E J ? H Q @ E J C = J U S = N N = J P U K B I A N ? D = J P = > E H E P U K N B P J A O O B K N = L = N P E ? Q H = N L Q N L K O A E J ? K J J A ? P E K J S E P D P D E O L N K @ Q ? P – K H U ? K = P – N K @ Q ? P O O D = H H J K P > A H E = > H A
B K N @ = I = C A O K B = J U O K N P E J ? H Q @ E J C N A I K P A K N ? K J O A M Q A J P E = H @ = I = C A O N A O Q H P E J C B N K I = J U ? H = E I A @ > N A = ? D K B = J U S = N N = J P U S D A P D A N A T L N A O O A @ K N E I L H E A @ – K H U ? K = P – N K @ Q ? P O O D = H H J K P > A
N A O L K J O E > H A B K N Q O A K B P D E O L N K @ Q ? P E J = I = J J A N P K E J B N E J C A K J = J U L = P A J P D A H @ > U K P D A N O & J = @ @ E P E K J J K S = N N = J P U K N C Q = N = J P A A E O > A E J C E O O Q A @ S E P D N A O L A ? P P K = L L A = N = J ? A ? K H K N B = @ E J C
? D = H G E J C O P = E J E J C O D N E J G = C A L A A H E J C J K N I = H S A = N = J @ P A = N K N E I L N K L A N = L L H E ? = P E K J > U P D A = L L H E ? = P K N ! = I = C A ? = Q O A @ > U = > Q O A J A C H A ? P = J @ H = ? G K B L N K L A N I = E J P A J = J ? A = ? P O K B J = P Q N A = J @
K N L D U O E ? = H I K R A I A J P K B P D A O Q > O P N = P A K N O P N Q ? P Q N = H @ A B A ? P O = N A = H O K A T ? H Q @ A @ B N K I P D A H E I E P A @ S = N N = J P U – K H U ? K = P – N K @ Q ? P O N A O A N R A O P D A N E C D P P K ? K J @ Q ? P L A N B K N I = J ? A P A O P O K J = J U I = P A N E = H
? H = E I A @ P K > A @ A B A ? P E R A L N E K N P K = J U N A L = E N O > U K S J A N C A J A N = H ? K J P N = ? P K N K N = L L H E ? = P K N
Disclaimer: H H C Q E @ A H E J A O N A ? K I I A J @ = P E K J O O P = P A I A J P O = J @ P A ? D J E ? = H @ = P = ? K J P = E J A @ D A N A E J = N A > = O A @ K J E J B K N I = P E K J = J @ P A O P O S A > A H E A R A P K > A N A H E = > H A = J @ ? K N N A ? P > Q P = ? ? Q N = ? U
= J @ ? K I L H A P A J A O O K B O = E @ P A O P O = N A J K P C Q = N = J P A A @ = J @ = N A J K P P K > A ? K J O P N Q A @ = O = S = N N = J P U A E P D A N A T L N A O O A @ K N E I L H E A @ & P E O P D A Q O A N O N A O L K J O E > E H E P U P K O = P E O B U D E I O A H B > U D E O
K S J E J B K N I = P E K J = J @ P A O P P K @ A P A N I E J A O Q E P = > E H E P U K B P D A L N K @ Q ? P B K N D E O K S J E J P A J @ A @ Q O A = L L H E ? = P E K J = J @ F K > O E P Q = P E K J = J @ Q O A N = O O Q I A O = H H N E O G = J @ H E = > E H E P U N A O Q H P E J C B N K I D E O Q O A
K B P D A L N K @ Q ? P 4 A @ K J K P O Q C C A O P K N C Q = N = J P A A P D = P = J U D = V = N @ H E O P A @ D A N A E J = N A P D A K J H U K J A O S D E ? D I = U A T E O P + A E P D A N O A H H A N J K N I = J Q B = ? P Q N A N O D = H H > A H E = > H A P K P D A > Q U A N K N = J U
P D E N @ L A N O K J B K N = J U E J F Q N U H K O O K N @ = I = C A @ E N A ? P H U K N E J @ E N A ? P H U N A O Q H P E J C B N K I Q O A K B K N E J = > E H E P U P K Q O A P D A L N K @ Q ? P / A ? K I I A J @ = P E K J O K N O P = P A I A J P O S D A P D A N E J S N E P E J C K N K N = H K P D A N
P D = J P D K O A ? K J P = E J A @ D A N A E J O D = H H J K P > A > E J @ E J C Q L K J P D A I = J Q B = ? P Q N A N Q J H A O O E J S N E P E J C = J @ O E C J A @ > U = ? K N L K N = P A K B B ? A N K B P D A I = J Q B = ? P Q N A N 1 A ? D J E ? = H = J @ = L L H E ? = P E K J E J B K N I = P E K J
E O L N K R E @ A @ B K N P D A L Q N L K O A K B A O P = > H E O D E J C = C A J A N = H L N K B H A K B P D A I = P A N E = H = J @ L N K L A N = L L H E ? = P E K J L N K ? A @ Q N A O 1 A O P L A N B K N I = J ? A N A O Q H P O S A N A K > P = E J A @ E J = ? K J P N K H H A @ A J R E N K J I A J P
= J @ – K H U ? K = P – N K @ Q ? P O I = G A O J K ? H = E I P D = P P D A O A P A O P O K N = J U K P D A N P A O P O = ? ? Q N = P A H U N A L N A O A J P = H H A J R E N K J I A J P O – K H U ? K = P – N K @ Q ? P O E O J K P N A O L K J O E > H A B K N P U L K C N = L D E ? = H A N N K N O
2021 Polycoat Products. All rights reserved. Revision 20210106EA
POLYCOAT PRODUCTS TEL 562.802.8834 | FAX 562.921.7363
info@polycoatusa.com | www.polycoatusa.com
by | Sep 27, 2025
PC-10 Page 1 of 2 Date: 05/10/2022
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
www.bjbenterprises.com
PC-10 A/B
A CURATIVE POLYURETHANE GEL
PC-10 A/B is a low viscosity, 15 Shore A polyurethane gel system originally designed as a re-enterable encapsulant for a variety of
electronic potting applications. It features excellent wetting and penetration properties. PC-10 A/B is easily re-enterable by hand or
tools.
Resists moisture absorption and is moisture insensitive
during handling
Non-foaming
Does not contain MOCA, MDA, or TDI
Non-corrosive and compatible with electrical
components
Very easy to use Cures at room temperature
PHYSICAL PROPERTIES TEST METHOD TEST RESULTS
Hardness, Shore A ASTM D2240 10 5
Density (g/cc) ASTM D792 0.95
Color/Appearance Visual Translucent Pale Yellow
Shrinkage (% by volume) 0.2
Water Resistance (% weight change) 30 days & 77 F (25 C) + 0.2
HANDLING PROPERTIES Part A Part B
Mix Ratio by weight 50 100
Specific Gravity @ 77 F (25 C) 1.02 0.91
Color Pale Yellow Colorless
Mixed Viscosity of A/B (cps) @ 77 F (25 C) Brookfield 150
Work Time of A/B, 100g mass @ 77 F (25 C) 5 10 minutes
Demold Time @ 77 F (25 C) 3 hours
Properties above are typical and not for specifications.
STORAGE:
Store at ambient temperatures, 65-80 F (18-27 C). Unopened containers will have a shelf life of 6 months from date of shipment when
properly stored at recommended temperatures. Purge opened containers with dry nitrogen before re-sealing.
SHORE A POLYURETHANES
Dedicated to QUALITY, SERVICE, SAFETY, and INNOVATION
An ISO-9001 Certified company
PC-10 Page 2 of 2 Date: 05/10/2022
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
NON-WARRANTY “Except for a warranty that materials substantially comply with the data presented in Manufacturer’s latest bulletin describing the product (the basis for this substantial
compliance is to be determined by the standard quality control tests generally performed by Manufacturer), all materials are sold “AS IS” and without any warranty express or implied as
to merchantability, fitness for a particular purpose, patent, trademark or copyright infringement, or as to any other matter. In no event shall Manufacturer’s liability for damages exceed
Manufacturer’s sale price of the particular quantity with respect to which damages are claimed.”
PACKAGING Part A Part B
Quart Kits 1 lb. 2 lbs.
Gallon Kits 4 lb. 8 lbs.
5-Gallon Kits 20 lbs. 40 lbs.
SAFETY PRECAUTIONS :
Use in a well-ventilated area. Avoid contact with skin using protective gloves and protective clothing. Repeat or prolonged contact
on the skin may cause an allergic reaction. Eye protection is extremely important. Always use approved safety glasses or goggles
when handling this product.
IF CONTACT OCCURS :
Skin: Immediately wash with soap and water. Remove contaminated clothing and launder before reuse. It is not recommended
to remove resin from skin with solvents. Solvents only increase contact and dry skin. Seek qualified medical attention if
allergic reactions occur.
Eyes: Immediately flush with water for at least 15 minutes. Call a physician.
Ingestion: If swallowed, call a physician immediately. Remove stomach contents by gastric suction or induce vomiting only as
directed by medical personnel. Never give anything by mouth to an unconscious person.
WARNING: This product can expose you to chemicals including 1,2-Benzenedicarboxylic acid, di-C9-11-branched alkyl
esters, C10-rich, which is known to the State of California to cause birth defects or other reproductive harm. For more information,
go to www.P65Warnings.ca.gov.
Refer to the Material Safety Data Sheet before using this product.
Handling Guide
by | Sep 27, 2025
PC-10 Page 1 of 2 Date: 05/10/2022
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
www.bjbenterprises.com
PC-10 A/B
A CURATIVE POLYURETHANE GEL
PC-10 A/B is a low viscosity, 15 Shore A polyurethane gel system originally designed as a re-enterable encapsulant for a variety of
electronic potting applications. It features excellent wetting and penetration properties. PC-10 A/B is easily re-enterable by hand or
tools.
Resists moisture absorption and is moisture insensitive
during handling
Non-foaming
Does not contain MOCA, MDA, or TDI
Non-corrosive and compatible with electrical
components
Very easy to use Cures at room temperature
PHYSICAL PROPERTIES TEST METHOD TEST RESULTS
Hardness, Shore A ASTM D2240 10 5
Density (g/cc) ASTM D792 0.95
Color/Appearance Visual Translucent Pale Yellow
Shrinkage (% by volume) 0.2
Water Resistance (% weight change) 30 days & 77 F (25 C) + 0.2
HANDLING PROPERTIES Part A Part B
Mix Ratio by weight 50 100
Specific Gravity @ 77 F (25 C) 1.02 0.91
Color Pale Yellow Colorless
Mixed Viscosity of A/B (cps) @ 77 F (25 C) Brookfield 150
Work Time of A/B, 100g mass @ 77 F (25 C) 5 10 minutes
Demold Time @ 77 F (25 C) 3 hours
Properties above are typical and not for specifications.
STORAGE:
Store at ambient temperatures, 65-80 F (18-27 C). Unopened containers will have a shelf life of 6 months from date of shipment when
properly stored at recommended temperatures. Purge opened containers with dry nitrogen before re-sealing.
SHORE A POLYURETHANES
Dedicated to QUALITY, SERVICE, SAFETY, and INNOVATION
An ISO-9001 Certified company
PC-10 Page 2 of 2 Date: 05/10/2022
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
NON-WARRANTY “Except for a warranty that materials substantially comply with the data presented in Manufacturer’s latest bulletin describing the product (the basis for this substantial
compliance is to be determined by the standard quality control tests generally performed by Manufacturer), all materials are sold “AS IS” and without any warranty express or implied as
to merchantability, fitness for a particular purpose, patent, trademark or copyright infringement, or as to any other matter. In no event shall Manufacturer’s liability for damages exceed
Manufacturer’s sale price of the particular quantity with respect to which damages are claimed.”
PACKAGING Part A Part B
Quart Kits 1 lb. 2 lbs.
Gallon Kits 4 lb. 8 lbs.
5-Gallon Kits 20 lbs. 40 lbs.
SAFETY PRECAUTIONS :
Use in a well-ventilated area. Avoid contact with skin using protective gloves and protective clothing. Repeat or prolonged contact
on the skin may cause an allergic reaction. Eye protection is extremely important. Always use approved safety glasses or goggles
when handling this product.
IF CONTACT OCCURS :
Skin: Immediately wash with soap and water. Remove contaminated clothing and launder before reuse. It is not recommended
to remove resin from skin with solvents. Solvents only increase contact and dry skin. Seek qualified medical attention if
allergic reactions occur.
Eyes: Immediately flush with water for at least 15 minutes. Call a physician.
Ingestion: If swallowed, call a physician immediately. Remove stomach contents by gastric suction or induce vomiting only as
directed by medical personnel. Never give anything by mouth to an unconscious person.
WARNING: This product can expose you to chemicals including 1,2-Benzenedicarboxylic acid, di-C9-11-branched alkyl
esters, C10-rich, which is known to the State of California to cause birth defects or other reproductive harm. For more information,
go to www.P65Warnings.ca.gov.
Refer to the Material Safety Data Sheet before using this product.
Handling Guide
by | Sep 27, 2025
PC-10 Page 1 of 2 Date: 05/10/2022
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
www.bjbenterprises.com
PC-10 A/B
A CURATIVE POLYURETHANE GEL
PC-10 A/B is a low viscosity, 15 Shore A polyurethane gel system originally designed as a re-enterable encapsulant for a variety of
electronic potting applications. It features excellent wetting and penetration properties. PC-10 A/B is easily re-enterable by hand or
tools.
Resists moisture absorption and is moisture insensitive
during handling
Non-foaming
Does not contain MOCA, MDA, or TDI
Non-corrosive and compatible with electrical
components
Very easy to use Cures at room temperature
PHYSICAL PROPERTIES TEST METHOD TEST RESULTS
Hardness, Shore A ASTM D2240 10 5
Density (g/cc) ASTM D792 0.95
Color/Appearance Visual Translucent Pale Yellow
Shrinkage (% by volume) 0.2
Water Resistance (% weight change) 30 days & 77 F (25 C) + 0.2
HANDLING PROPERTIES Part A Part B
Mix Ratio by weight 50 100
Specific Gravity @ 77 F (25 C) 1.02 0.91
Color Pale Yellow Colorless
Mixed Viscosity of A/B (cps) @ 77 F (25 C) Brookfield 150
Work Time of A/B, 100g mass @ 77 F (25 C) 5 10 minutes
Demold Time @ 77 F (25 C) 3 hours
Properties above are typical and not for specifications.
STORAGE:
Store at ambient temperatures, 65-80 F (18-27 C). Unopened containers will have a shelf life of 6 months from date of shipment when
properly stored at recommended temperatures. Purge opened containers with dry nitrogen before re-sealing.
SHORE A POLYURETHANES
Dedicated to QUALITY, SERVICE, SAFETY, and INNOVATION
An ISO-9001 Certified company
PC-10 Page 2 of 2 Date: 05/10/2022
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
NON-WARRANTY “Except for a warranty that materials substantially comply with the data presented in Manufacturer’s latest bulletin describing the product (the basis for this substantial
compliance is to be determined by the standard quality control tests generally performed by Manufacturer), all materials are sold “AS IS” and without any warranty express or implied as
to merchantability, fitness for a particular purpose, patent, trademark or copyright infringement, or as to any other matter. In no event shall Manufacturer’s liability for damages exceed
Manufacturer’s sale price of the particular quantity with respect to which damages are claimed.”
PACKAGING Part A Part B
Quart Kits 1 lb. 2 lbs.
Gallon Kits 4 lb. 8 lbs.
5-Gallon Kits 20 lbs. 40 lbs.
SAFETY PRECAUTIONS :
Use in a well-ventilated area. Avoid contact with skin using protective gloves and protective clothing. Repeat or prolonged contact
on the skin may cause an allergic reaction. Eye protection is extremely important. Always use approved safety glasses or goggles
when handling this product.
IF CONTACT OCCURS :
Skin: Immediately wash with soap and water. Remove contaminated clothing and launder before reuse. It is not recommended
to remove resin from skin with solvents. Solvents only increase contact and dry skin. Seek qualified medical attention if
allergic reactions occur.
Eyes: Immediately flush with water for at least 15 minutes. Call a physician.
Ingestion: If swallowed, call a physician immediately. Remove stomach contents by gastric suction or induce vomiting only as
directed by medical personnel. Never give anything by mouth to an unconscious person.
WARNING: This product can expose you to chemicals including 1,2-Benzenedicarboxylic acid, di-C9-11-branched alkyl
esters, C10-rich, which is known to the State of California to cause birth defects or other reproductive harm. For more information,
go to www.P65Warnings.ca.gov.
Refer to the Material Safety Data Sheet before using this product.
Handling Guide
by | Sep 27, 2025
2012
February 2012
PB FAST SET One Part Bonding Adhesive DESCRIPTION: PB Fast Set is an amber-colored, one-part, urethane adhesive that fully cures in 30 minutes. It works well for indoor or outdoor applications. It cures from liquid to solid with a slight amount of moisture. Use it to join Precision Board Plus high density urethane sheets to make them longer or wider, and for laminating sheets together to make them thicker. Consistency of PB Fast Set is similar to honey, making it easy to apply directly from the container. No mixing is required. Works well on wood, metal and most other materials. Easy to cut, carve, sand or machine and cuts cleanly (Working time: Approximately 4 minutes). For slower cure and more working time, use PB Bond-240. Working time: Approximately 4 minutes. Preparation – Lightly spray the mating surfaces with water, or wipe the surfaces with a damp rag just prior to applying the PB Fast Set. This procedure assures there will be adequate moisture to effect total cure. PB Fast Set will not cure properly without adding moisture. Excessive water will slow cure time, and soften adhesive. Application – Apply a very thin coat of PB Fast Set to one of the surfaces to be joined, applying only enough to change the color of Precision Board Plus. Excess adhesive will be pushed out of the joint. Hold pieces in place by clamping or by setting something heavy on each side of the joint. Clean up wet adhesive with acetone. Keep container closed when not in use. Coverage is approximately 1/2 ounce per square foot. Edge Bonding – After application, the adhesive will start to bubble and thicken in approximately 1-2 minutes. Keep the Precision Board pieces on edge during this time so that the PB Fast Set will not run out of the joint before it sets. If the adhesive runs out, the joint may look solid but will be hollow inside, therefore extremely weak. Laminate Bonding – When making laminate bonds, the moisture added will assure total cure. If moisture is not added there will be spots of uncured adhesive where moisture was unable to penetrate. Even long term drying will not complete reaction since PB does not absorb moisture from the air and pass it through to the joint. Sandblasting When edge-bonding pieces that will be sandblasted, do not apply PB Fast Set to the top part of the joint since it will be blasted away later. Clamping is necessary, as thick bond lines are harder to blast through. Remove any excess adhesive from the joint. Tips For Easier Usage Lightly spray or wipe mating pieces with water just prior to application. Too much water slows cure. Apply just enough PB Fast Set to change the color of Precision Board Plus. Allow PB Fast Set to slightly bubble and thicken before pushing pieces together. Allow minimum of 30 minutes prior to moving bonded part. Keep adhesive back from outer edge for ease of sandblasting. Clamping is necessary. To blend joint into background after sanding, prime with FSC-88 WB primer/filler. Drill small hole in cap to act as dispensing nozzle. After using, cover hole with tape. NOTE: For questions regarding use of PB Fast Set, please contact Coastal Enterprises at (800) 845-0745. See the training video at www.precisionboard.com CAUTION: For industrial use only. Use with adequate ventilation. Avoid prolonged contact with skin. Close container after each use. Do not take internally. Do not transfer contents to bottles or other unlabeled containers. Harmful or fatal if swallowed. Do not induce vomiting. Call physician immediately. KEEP OUT OF REACH OF CHILDREN. WARRANTY: All recommendations for product use have been derived from experience and test data believed to be reliable. We warrant and guarantee the uniformity of our products within manufacturing tolerance. However, since the use of our products are beyond our direct control, they are furnished upon the condition that each party shall make his/her own tests to determine their suitability for his/her particular purpose. Except as stated herein, Coastal Enterprises Company makes no warranty or guarantee, expressed or implied, and disclaims all responsibility for results obtained, nor assumes any liability for any damages, whether arising out of negligence or breach of guarantee and is hereby expressly limited to replacement of product only. For additional information on product handling, please refer to PB Fast Set MSDS.
by | Sep 27, 2025
For more information or to view
our how to video, scan here.
!”#$%&'()*+”(,$-.’/(‘$0+”)/0)$122314532645$7$$88839:’0*(*+”;+/:<30+=
PRODUCT DATA SHEET
Rev. 9.15.19
PB Bond-240
One Part Bonding Adhesive
Description:
PB Bond-240 is an amber colored, one part, urethane adhesive that works well for indoor or outdoor applications.
It cures from a liquid to a solid state with a slight amount of moisture. Use it to join Precision Board high density
urethane sheets with butt bonds to make them longer or wider, and for laminating sheets together to make them
thicker. Consistency of PB Bond-240 is similar to honey, making it easy to apply directly from the container. No
mixing is required. Cure time: 4 hours before moving, full strength in 12 hours.
Preparation - Lightly spray the mating surfaces with water or wipe the surfaces with a damp rag just prior to applying
the PB Bond-240. This procedure assures there will be adequate moisture to effect total cure.
PB Bond-240 will not cure properly without adding moisture.
Application - Apply a thin coat of PB Bond-240 to each surface to be joined. Only apply enough to change the color
of Precision Board. Too much adhesive will be pushed out of the joint. Hold pieces in place by clamping or by setting
something heavy on each side of the joint. Clean up wet adhesive with acetone. Keep container closed when not in
use. Spread rate - approximately 1/2 ounce per square foot.
Edge Bonding - After application, the adhesive will start to bubble and thicken in approximately 7-8 minutes. Keep
the Precision Board pieces on edge during this time so that the PB Bond-240 will not run out of the joint before it sets.
If the adhesive runs out, the joint may look solid but will be hollow inside, therefore extremely weak.
Laminate Bonding - When making laminate bonds, the moisture added will assure total cure. If moisture is not
added there will be spots of uncured adhesive where moisture was unable to penetrate. Even long term drying will
not assure cure since Precision Board does not absorb moisture from the air and pass it through to the joint.
Sandblasting - When butt bonding pieces that will be sandblasted, apply the PB Bond-240 lighter at the top part of
the joint since it will be blasted away later. This makes blasting much easier. Thick glue lines are harder to blast
through. Remove any excess ooze from the joint. Clamping is necessary to keep glue lines to a minimum.
Tips for Easier Usage
Lightly spray or wipe mating pieces with water just prior to application.
Apply just enough PB Bond-240 to change the color of Precision Board.
Allow PB Bond-240 to slightly bubble and thicken before pushing pieces together.
Allow minimum 4 hours cure prior to moving bonded part. Full strength in 12 hours.
Keep glue line as thin as possible for ease of sandblasting. Clamping is necessary.
To blend joint into background after sanding, prime both joint and background with
FSC-88 WB primer/filler.
Drill small hole in cap to act as dispensing nozzle. After using, cover hole with tape.
NOTE: For questions regarding use of PB Bond-240, please contact Coastal Enterprises at (800) 845-0745. Watch
the training video at www.precisionboard.com.
CAUTION: For industrial use only. Use with adequate ventilation. Use gloves and appropriate PPE. Avoid prolonged
contact with skin. Close container after each use. Do not take internally. Do not transfer contents to bottles or other
unlabeled containers. Harmful or fatal if swallowed. Do not induce vomiting. Call physician immediately.
KEEP OUT OF REACH OF CHILDREN.
WARRANTY: All recommendations for product use have been derived from experience and test data believed to be reliable. We warrant and guarantee the uniformity of our products within manufacturing
tolerance. However, since the use of our products are beyond our direct control, they are furnished upon the condition that each party shall make his/her own tests to determine their suitability for his/her
particular purpose. Except as stated herein, Coastal Enterprises Company makes no warranty or guarantee, expressed or implied, and disclaims all responsibility for results obtained, nor assumes any
liability for any damages, whether arising out of negligence or breach of guarantee and is hereby expressly limited to replacement of product only. For additional information on product handling, please
refer to PB Bond-240 SDS.
For more information or to view
our how to video, scan here.
www.precisionboard.com
by | Sep 27, 2025
For more information or to view
our how to video, scan here.
!”#$%&'()*+”(,$-.’/(‘$0+”)/0)$122314532645$7$$88839:’0*(*+”;+/:<30+=
PRODUCT DATA SHEET
Rev. 9.15.19
PB Bond-240
One Part Bonding Adhesive
Description:
PB Bond-240 is an amber colored, one part, urethane adhesive that works well for indoor or outdoor applications.
It cures from a liquid to a solid state with a slight amount of moisture. Use it to join Precision Board high density
urethane sheets with butt bonds to make them longer or wider, and for laminating sheets together to make them
thicker. Consistency of PB Bond-240 is similar to honey, making it easy to apply directly from the container. No
mixing is required. Cure time: 4 hours before moving, full strength in 12 hours.
Preparation - Lightly spray the mating surfaces with water or wipe the surfaces with a damp rag just prior to applying
the PB Bond-240. This procedure assures there will be adequate moisture to effect total cure.
PB Bond-240 will not cure properly without adding moisture.
Application - Apply a thin coat of PB Bond-240 to each surface to be joined. Only apply enough to change the color
of Precision Board. Too much adhesive will be pushed out of the joint. Hold pieces in place by clamping or by setting
something heavy on each side of the joint. Clean up wet adhesive with acetone. Keep container closed when not in
use. Spread rate - approximately 1/2 ounce per square foot.
Edge Bonding - After application, the adhesive will start to bubble and thicken in approximately 7-8 minutes. Keep
the Precision Board pieces on edge during this time so that the PB Bond-240 will not run out of the joint before it sets.
If the adhesive runs out, the joint may look solid but will be hollow inside, therefore extremely weak.
Laminate Bonding - When making laminate bonds, the moisture added will assure total cure. If moisture is not
added there will be spots of uncured adhesive where moisture was unable to penetrate. Even long term drying will
not assure cure since Precision Board does not absorb moisture from the air and pass it through to the joint.
Sandblasting - When butt bonding pieces that will be sandblasted, apply the PB Bond-240 lighter at the top part of
the joint since it will be blasted away later. This makes blasting much easier. Thick glue lines are harder to blast
through. Remove any excess ooze from the joint. Clamping is necessary to keep glue lines to a minimum.
Tips for Easier Usage
Lightly spray or wipe mating pieces with water just prior to application.
Apply just enough PB Bond-240 to change the color of Precision Board.
Allow PB Bond-240 to slightly bubble and thicken before pushing pieces together.
Allow minimum 4 hours cure prior to moving bonded part. Full strength in 12 hours.
Keep glue line as thin as possible for ease of sandblasting. Clamping is necessary.
To blend joint into background after sanding, prime both joint and background with
FSC-88 WB primer/filler.
Drill small hole in cap to act as dispensing nozzle. After using, cover hole with tape.
NOTE: For questions regarding use of PB Bond-240, please contact Coastal Enterprises at (800) 845-0745. Watch
the training video at www.precisionboard.com.
CAUTION: For industrial use only. Use with adequate ventilation. Use gloves and appropriate PPE. Avoid prolonged
contact with skin. Close container after each use. Do not take internally. Do not transfer contents to bottles or other
unlabeled containers. Harmful or fatal if swallowed. Do not induce vomiting. Call physician immediately.
KEEP OUT OF REACH OF CHILDREN.
WARRANTY: All recommendations for product use have been derived from experience and test data believed to be reliable. We warrant and guarantee the uniformity of our products within manufacturing
tolerance. However, since the use of our products are beyond our direct control, they are furnished upon the condition that each party shall make his/her own tests to determine their suitability for his/her
particular purpose. Except as stated herein, Coastal Enterprises Company makes no warranty or guarantee, expressed or implied, and disclaims all responsibility for results obtained, nor assumes any
liability for any damages, whether arising out of negligence or breach of guarantee and is hereby expressly limited to replacement of product only. For additional information on product handling, please
refer to PB Bond-240 SDS.
For more information or to view
our how to video, scan here.
www.precisionboard.com
by | Sep 27, 2025
For more information or to view
our how to video, scan here.
!”#$%&'()*+”(,$-.’/(‘$0+”)/0)$122314532645$7$$88839:’0*(*+”;+/:<30+=
PRODUCT DATA SHEET
Rev. 9.15.19
PB Bond-240
One Part Bonding Adhesive
Description:
PB Bond-240 is an amber colored, one part, urethane adhesive that works well for indoor or outdoor applications.
It cures from a liquid to a solid state with a slight amount of moisture. Use it to join Precision Board high density
urethane sheets with butt bonds to make them longer or wider, and for laminating sheets together to make them
thicker. Consistency of PB Bond-240 is similar to honey, making it easy to apply directly from the container. No
mixing is required. Cure time: 4 hours before moving, full strength in 12 hours.
Preparation - Lightly spray the mating surfaces with water or wipe the surfaces with a damp rag just prior to applying
the PB Bond-240. This procedure assures there will be adequate moisture to effect total cure.
PB Bond-240 will not cure properly without adding moisture.
Application - Apply a thin coat of PB Bond-240 to each surface to be joined. Only apply enough to change the color
of Precision Board. Too much adhesive will be pushed out of the joint. Hold pieces in place by clamping or by setting
something heavy on each side of the joint. Clean up wet adhesive with acetone. Keep container closed when not in
use. Spread rate - approximately 1/2 ounce per square foot.
Edge Bonding - After application, the adhesive will start to bubble and thicken in approximately 7-8 minutes. Keep
the Precision Board pieces on edge during this time so that the PB Bond-240 will not run out of the joint before it sets.
If the adhesive runs out, the joint may look solid but will be hollow inside, therefore extremely weak.
Laminate Bonding - When making laminate bonds, the moisture added will assure total cure. If moisture is not
added there will be spots of uncured adhesive where moisture was unable to penetrate. Even long term drying will
not assure cure since Precision Board does not absorb moisture from the air and pass it through to the joint.
Sandblasting - When butt bonding pieces that will be sandblasted, apply the PB Bond-240 lighter at the top part of
the joint since it will be blasted away later. This makes blasting much easier. Thick glue lines are harder to blast
through. Remove any excess ooze from the joint. Clamping is necessary to keep glue lines to a minimum.
Tips for Easier Usage
Lightly spray or wipe mating pieces with water just prior to application.
Apply just enough PB Bond-240 to change the color of Precision Board.
Allow PB Bond-240 to slightly bubble and thicken before pushing pieces together.
Allow minimum 4 hours cure prior to moving bonded part. Full strength in 12 hours.
Keep glue line as thin as possible for ease of sandblasting. Clamping is necessary.
To blend joint into background after sanding, prime both joint and background with
FSC-88 WB primer/filler.
Drill small hole in cap to act as dispensing nozzle. After using, cover hole with tape.
NOTE: For questions regarding use of PB Bond-240, please contact Coastal Enterprises at (800) 845-0745. Watch
the training video at www.precisionboard.com.
CAUTION: For industrial use only. Use with adequate ventilation. Use gloves and appropriate PPE. Avoid prolonged
contact with skin. Close container after each use. Do not take internally. Do not transfer contents to bottles or other
unlabeled containers. Harmful or fatal if swallowed. Do not induce vomiting. Call physician immediately.
KEEP OUT OF REACH OF CHILDREN.
WARRANTY: All recommendations for product use have been derived from experience and test data believed to be reliable. We warrant and guarantee the uniformity of our products within manufacturing
tolerance. However, since the use of our products are beyond our direct control, they are furnished upon the condition that each party shall make his/her own tests to determine their suitability for his/her
particular purpose. Except as stated herein, Coastal Enterprises Company makes no warranty or guarantee, expressed or implied, and disclaims all responsibility for results obtained, nor assumes any
liability for any damages, whether arising out of negligence or breach of guarantee and is hereby expressly limited to replacement of product only. For additional information on product handling, please
refer to PB Bond-240 SDS.
For more information or to view
our how to video, scan here.
www.precisionboard.com
by | Sep 27, 2025
TD035 ICP Group, Inc. Rev 1/2021-1 Page 1 of 3
TECHNICAL DATA SHEET
HANDIFOAM
COMMERCIAL VEHICLE SPRAY FOAM
LOW PRESSURE POLYURETHANE FOAM INFORMATION
Description Low pressure, medium density, black in color, two-component spray polyurethane foam
SPF Spray Polyurethane Foam
Applications Designed to coat flat or irregular surfaces. The foam easily blends in with the undercarriages of RVs and other
vehicles while helping to reduce vibration and deaden sound.
Preparation for
use
Substrate must be clean, dry, firm, free of loose particles, and free of dust, grease, and mold release agents.
Protect surfaces not to be foamed. Read SDS, Operating Instructions, and Product Stewardship Guidelines. For
additional information go to www.Handifoam.com
Use Condition chemicals to 75-85 F (24-29 C). Follow instructions for set-up found in the operating instructions.
PPE
Recommend using in a well-ventilated area with certified respiratory protection or a powered air purifying
respirator (PAPR). Wear protective glasses with side shields or goggles, nitrile gloves, and clothing that protects
against dermal exposure. Read all instructions and SDS prior to use of any product.
Note FOR PROFESSIONAL USE ONLY. Always check the local building code before use. Cured low pressure
polyurethane foam is non-toxic and inert.
Product Storage Store in a dry area. Do not expose the kits or tanks to open flame or temperatures above 90 F (32 C).
Excessive heat can cause premature aging of components resulting in a shorter shelf-life.
Temperature Please see chart located on page 2.
Disposal Refer to SDS (Section 13) for instructions. Always dispose of empty cylinders in accordance with all applicable
federal, state, provincial and local regulations.
Shelf-life 12 months
Compatibility Cured low pressure polyurethane foam is chemically inert and non-reactive in approved applications, and will not
harm electrical wire insulations, extruded polystyrene foams, Romex
, rubber, PVC, polyethylene (i.e. PEX) or
other plastics. The product is not resistant to UV rays; if left exposed the product should be coated or painted.
TECHNICAL DATA STANDARD RESULTS
Density Free Rise ASTM D1622 1.75 lbs/ft
3
(28 kg/m
3
)
K-factor- Aged 90 days 140
F (60
C) ASTM C518 0.139 BTU inch/ft
2
h F
0.166 BTU inch/ft
2
h F
0.083 BTU inch/ft
2
h F
R-Value- Aged 90 days 140
F (60
C) ASTM C518 7.2 at 1 inch thickness
6.0 at 1 inch thickness
12.0 at 2 inch thickness
Air Barrier Properties-Estimated ASTM E283 0.003 cfm/ft
2
(0.02 L/s/m
2
)
Tested at 1 inch thickness @1.57 psf (75 Pa)
Perm Rating-1 inch thickness ASTM E96 0.02 L/s/m
2
Compressive Strength ASTM D1621 26 lbf/in
2
(182 kPa) Parallel
Dimensional Stability ASTM D2126 +/- 5%
Tack-Free/Expansion Time Tack-Free/Expansion Time 30-60 seconds
Closed-Cell Content ASTM D2856 95%
Cuttable 2-5 minutes
HandiFoam
Commercial Vehicle Spray Foam
TD035 ICP Group, Inc. Rev 1/2021-1 Page 2 of 3
Fungi Resistance ASTM G21 No Growth
Fire Rating FMVSS302/CMVSS 302 Meets/ Burn Rate 0/00 min
Fire Rating- Tested at 1 Thickness ASTM E84 Flame Spread Index 20
Smoke Developed 400
APPROVALS/STANDARDS/CLASSIFICATIONS
TEMPERATURE GUIDELINES
Chemical Storage Temperature Optimum 75-85 F (24-29 C) but not <60 F (16 C) or >90 F (32 C)
Outside Application Temperature 40-100 F (4-38 C)
Process Core Chemical Temperature 75-85 F (24-29 C)
Surface Temperature (Substrate) 40-100 F (4-38 C)
Cured Foam
–
200 F to
+
240 F (
–
129 C to
+
116 C)
YIELD
1
(2.10 Free Rise Density)
Weight
(Including Packaging)
Board Feet Cubic Feet
P12756 116 lbs
(52.6 kg)
504
(46.8 m
2
)
42.0 ft
3
(1.19 m
3
)
1
Yield is based on free-rise density. We state our core density/free-rise density when describing the foam. Applying foam into a cavity may result
in higher in-place densities due to packing effects. These higher densities may result in lower yields.
ASTM E84 Conforms to the requirements of ASTM E84 and is classified as a class 1 (A) material. Tested at 1 inch
thickness
HandiFoam
Commercial Vehicle Spray Foam
TD035 ICP Group, Inc. Rev 1/2021-1 Page 3 of 3
NOTE: Physical properties shown are typical and are to serve only as a guide for engineering design. Results are obtained from specimens under ideal laboratory
conditions and may vary upon use, temperature and ambient conditions. Right to change physical properties as a result of technical progress is reserved. Yields shown
are optimum and will vary slightly depending on ambient conditions and application. This information supersedes all previously published data. The customer is
responsible for deciding whether products and associated TDS information are appropriate for customer s use.
WARNING:
ICP low pressure one-component polyurethane foam sealants and adhesives (OCF), low pressure spray polyurethane foams and foam adhesives (SPF), and low pressure
pour-in-place polyurethane foams (PIP) are composed of diisocyanate, hydrofluorocarbon, hydrocarbon, hydrofluoroolefin or hydrochlorofluoroolefin blowing agent, and a
polyol blend. The urethane foam produced from these ingredients will support combustion and may present a fire hazard if exposed to a fire or excessive heat about 240 F
(116 C). Read all instructions, ICP Product Stewardship Guidelines and SDS (Section 8) prior to use of any product. ICP polyurethane products are for professional use
only.
Before using any OCF, SPF or PIP product, read the SDS and instructions carefully before use (www.handifoam.com). OCF Products: wear protective glasses with side
shields or goggles, nitrile gloves, and clothing that protects against dermal exposure. Recommend using in a well-ventilated area. Avoid breathing vapors. SPF/PIP
Products: wear protective glasses with side shields or goggles unless using a full-face respirator, nitrile gloves, and clothing that protects against dermal exposure.
Recommend dispensing product in a well-ventilated area and with certified respiratory protection or a powered air purifying respirator (PAPR); however, well ventilated
exterior applications may not need respiratory protection. It is the responsibility of the employer to complete a PPE evaluation and/or exposure assessment to determine if
respiratory protection is required. Personal Protective Equipment can be purchased through ICP Building Solutions Group by ordering the Polyset Contractor Safety Kit
(F65251). The Contractor Safety Kit includes: nitrile gloves, contractor safety glasses, and a size Medium NIOSH-approved negative pressure half mask respirator.
Refer to each product s TDS for specifications, testing results, and other attributes. The customer is ultimately responsible for deciding whether products and associated
TDS information are appropriate for customer s use. For professional use only. Building practices unrelated to materials can lead to potential mold issues. Material suppliers
cannot provide assurance that mold will not develop in any specific system. Product uses a non-flammable compressed gas. Keep away from heat. Smoking and open
flames, including hot work, should be prohibited in the vicinity of a foaming operation. Avoid contact with skin and eyes. May cause sensitization by inhalation and/or direct
skin contact. Persons previously sensitized to Isocyanates may develop a cross-sensitization reaction to other isocyanates. Avoid prolonged or repeated breathing of vapor.
Use in conformance with all local, state and federal regulations and safety requirements. Failure to strictly adhere to any recommended procedures and reasonable safety
precautions shall release ICP Building Solutions Group of all liability with respect to the materials or the use thereof. For additional information and location of your nearest
distributor, call ICP Building Solutions Group 330.753.4585.
LIMITED WARRANTY and LIMITATION OF DAMAGES: ICP Building Solutions Group warrants only that the product shall meet ICP Building Solutions Group s
specifications for the product when shipped by ICP Building Solutions Group. NO OTHER EXPRESSED OR IMPLIED WARRANTIES APPLY AND ANY IMPLIED
WARRANTIES OF MERCH ANTABILITY, NON-INFRINGEMENT OUTSIDE THE U.S. AND FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY DISCLAIMED.
Buyer and users assume all risks of use, handling and storage of the product. Failure to strictly adhere to any recommended procedures shall release ICP Building Solutions
Group from all liability. The user of the product is responsible to determine suitability of the product for the particular use. The exclusive remedy as to any breach of warranty,
negligence or other claim is limited to the replacement of the product. Liability for any indirect, incidental or consequential damage or loss is specifically excluded.
by | Sep 27, 2025
HandiFoam
E84 Spray Foam Insulation Low Pressure Spray Foam
TD062 ICP Construction, Inc. Rev 01 /2025-3 Page 1 of 3
TECHNICAL DATA SHEET
HANDIFOAM
E84 SPRAY FOAM INSULATION LOW PRESSURE
SPRAY FOAM
LOW PRESSURE POLYURETHANE FOAM INFORMATION
Description (HFO) Low pressure, medium density, two-component spray polyurethane foam
SPF Spray Polyurethane Foam
Applications Designed to fill and seal various size voids, deaden sound, or reduce vibration. Conforms to the requirements of
ASTM E84 as a Class 1 (A) system.
Preparation for
use
Substrate must be clean, dry, firm, free of loose particles, and free of dust, grease, and mold release agents.
Protect surfaces not to be foamed. Read SDS, Operating Instructions, and Product Stewardship Guidelines. For
additional information go to www.handifoam.com
Use Condition chemical to 75-85 F (24-29 C). Follow instructions for set-up found in the operating instructions.
PPE
Recommend using in a well- ventilated area with certified respiratory protection or a powered air purifying
respirator (PAPR). Wear protective glasses with side shields or goggles, nitrile gloves, and clothing that protects
against dermal exposure. Read all instructions and SDS (Section 8) prior to use of any product.
Note FOR PROFESSIONAL USE ONLY. Always check the local building code before use. Cured low pressure
polyurethane foam is non-toxic and inert.
Temperature Please see Temperature Guidelines located on page 2
Product Storage Store in a dry area. Do not expose the cylinders to open flame or temperatures above 90 F (32 C). Excessive
heat can cause premature aging of components resulting in a shorter shelf-life.
Disposal Refer to SDS (Section 13) for instructions. Always dispose of empty cylinders according to applicable federal,
state, provincial and local regulations.
Shelf-life 24 months
Compatibility Cured low pressure polyurethane foam is chemically inert and non- reactive in approved applications, and will not
harm electrical wire insulations, extruded polystyrene foams, Romex
, rubber, PVC, polyethylene (i.e. PEX) or
other plastics. The product is not resistant to UV rays; if left exposed the product should be coated or painted.
TECHNICAL DATA STANDARD RESULTS
Density Free Rise
ASTM D1622
1.75 lbs/ft
3
(28.0 kg/m
3
)
Density In-place 2.11 lbs/ft
3
(35.2 kg/m
3
)
Tack-Free/Expansion Time — 30-60 seconds
Cuttable — 10 minutes (estimate)
K-factor- Initial
Initial
ASTM C518
0.152 BTU inch/ft
2
h F at 1 thickness
0.076 BTU inch/ft
2
h F at 2 thickness
Aged 180 days @ 75 F (24 C)
Aged 180 days @ 75 F (24 C)
0.169 BTU inch/ft
2
h F at 1 thickness
0.085 BTU inch/ft
2
h F at 2 thickness
R-Value- Initial
Initial
ASTM C518
6.6 at 1 thickness
13.2 at 2 thickness
Aged 180 days @ 75 F (24 C)
Aged 180 days @ 75 F (24 C)
6.1 at 1 thickness
11.7 at 2 thickness
Air Barrier Properties
Tested at 1 thickness @1.57 psf (75 Pa)
ASTM E283 – modified
0.003 cfm/ft
2
(0.02 L/s/m
2
)
Air Permeance
@1.57 psf (75Pa)
ASTM E2178
0.0008 cfm/ft
2
(0.004 L/s/m
2
)
Perm Rating- Method A
1.5 Thick (3.8 cm) ASTM E96 (Method A) 1.4 perms – Class III Vapor Retarder
HandiFoam
E84 Spray Foam Insulation Low Pressure Spray Foam
TD062 ICP Construction, Inc. Rev 01 /2025-3 Page 2 of 3
TECHNICAL DATA (Continued) STANDARD RESULTS
Closed-Cell Content ASTM D2856 > 90%
Fungi Resistance ASTM G21 No Growth
Compressive Strength ASTM D1621 24.2 lbf/in
2
(167 kPa) Parallel
Tensile Strength ASTM D1623 40.3 lbf/in
2
(278 kPa) Parallel
Dimensional Stability
70 F (22 C) & 50% R.H. / 28 days
-4 F (-20 C) / 28 days
158 F (70 C) & 97% R.H. / 28 days
ASTM D2126
(% volumetric change)
5
5
+0.96
Water Absorption ASTM D2842 0.83%
VOC Content EPA Method 24 (Calculated) 37 g/l when mixed as intended
Fire Rating- Tested at 2 Thickness.
Class A
ASTM E84
Flame Spread Index 5
Smoke Developed 450
Fire Rating- Tested at 4 Beads
CAN/ULC- S102
Flame Spread Index 20
Smoke Developed 60
APPROVALS/STANDARDS/CLASSIFICATIONS
TEMPERATURE GUIDELINES
Chemical Storage Temperature Optimum 75-85 F (24-29 C) but not <60 F (16 C) or >90 F (32 C)
Outside Application Temperature 40-100 F (4-38 C)
Process Core Chemical Temperature 75-85 F (24-29 C)
Surface Temperature (Substrate) 40-100 F (4-38 C)
Cured Foam -200 to +240 F (-129 to +116 C)
YIELD
1
(1.75 lbs/ft
3
Free Rise Density)
Weight
(Incl. packaging)
Board Feet
(Up to)
Cubic Feet
(Up to)
Linear Feet
(Up to)
Linear Feet
(Up to)
P12135 (II-105) 26.4 lbs
(12.0 kg)
105 ft
2
(9.7 m
2
)
8.7 ft
3
(0.25 m
3
)
1,605 ft at 1 bead 401 ft at 2 bead
P12140 (II- 205) 41.0 lbs
(18.6 kg)
205 ft
2
(19.0 m
2
)
17.0 ft
3
(0.48 m
3
)
3,132 ft at 1 bead 783 ft at 2 bead
P12145 (II- 605) 115.7 lbs
(52.5 kg)
605 ft
2
(56.2 m
2
)
50.4 ft
3
(1.43 m
3
)
9,244 ft at 1 bead 2,311 ft at 2 bead
1
Yield is based on free-rise density. We state our core density/free-rise density when describing the foam. Applying foam into a cavity may result in higher in-place
densities due to packing effects. These higher densities may result in lower yields.
ULe GREENGUARD Testing complete
CCMC Testing in progress for CAN/ULC S711.01
ICC-ES Testing in progress
NFPA 286 Testing for use in roof/wall junctions and attic/wall penetrations at 2
thickness x 6 wide with unlimited length without a thermal barrier.
HandiFoam
E84 Spray Foam Insulation Low Pressure Spray Foam
TD062 ICP Construction, Inc. Rev 0 1/2025-3 Page 3 of 3
NOTE: Physical properties shown are typical and are to serve only as a guide for engineering design. Results are obtained from specimens under
ideal laboratory conditions and may vary upon use, temperature and ambient conditions. Right to change physical properties as a result of technical
progress is reserved. Yields shown are optimum and will vary slightly depending on ambient conditions and application. This information supersedes
all previously published data. The customer is responsible for deciding whether products and associated TDS information are appropriate for
customer s use.
WARNING:
ICP low pressure one- component polyurethane foam sealants and adhesives (OCF), low pressure spray polyurethane foams and foam adhesives
(SPF), and low pressure pour-in-place polyurethane foams (PIP) are composed of diisocyanate, hydrofluorocarbon, hydrocarbon, hydrofluoroolefin or
hydrochlorofluoroolefin blowing agent, and a polyol blend. The urethane foam produced from these ingredients will support combustion and may
present a fire hazard if exposed to a fire or excessive heat about 240 F (116 C). Read all instructions, ICP Product Stewardship Guidelines and SDS
(Section 8) prior to use of any product. ICP polyurethane products are for professional use only.
Before using any OCF, SPF or PIP product, read the SDS and instructions carefully before use (www.handifoam.com). OCF Products: wear
protective glasses with side shields or goggles, nitrile gloves, and clothing that protects against dermal exposure. Recommend using in a well –
ventilated area. Avoid breathing vapors. SPF/PIP Products: wear protective glasses with side shields or goggles unless using a full-face respirator,
nitrile gloves, and clothing that protects against dermal exposure. Recommend dispensing product in a well-ventilated area and with certified
respiratory protection or a powered air purifying respirator (PAPR); however, well ventilated exterior applications may not need respiratory protection.
It is the responsibility of the employer to complete a PPE evaluation and/or exposure assessment to determine if respiratory protection is required.
Personal Protective Equipment can be purchased through ICP by ordering the Polyset Contractor Safety Kit (F65251). The Contractor Safety Kit
includes nitrile gloves, contractor safety glasses, and a size Medium NIOSH-approved negative pressure half mask respirator.
Refer to each product s TDS for specifications, testing results, and other attributes. The customer is ultimately responsible for deciding whether
products and associated TDS information are appropriate for customer s use. For professional use only. Building practices unrelated to materials can
lead to potential mold issues. Material suppliers cannot provide assurance that mold will not develop in any specific system. Product uses a non-
flammable compressed gas. Keep away from heat. Smoking and open flames, including hot work, should be prohibited in the vicinity of a foaming
operation. Avoid contact with skin and eyes. May cause sensitization by inhalation and/or direct skin contact. Persons previously sensitized to
Isocyanates may develop a cross-sensitization reaction to other isocyanates. Avoid prolonged or repeated breathing of vapor. Use in conformance with
all local, state and federal regulations and safety requirements. Failure to strictly adhere to any recommended procedures and reasonable safety
precautions shall release ICP of all liability with respect to the materials or the use thereof. For additional information and location of your nearest
distributor, call ICP 330.753.4585.
LIMITED WARRANTY and LIMITATION OF DAMAGES: ICP warrants only that the product shall meet ICP specifications for the product when shipped
by ICP. NO OTHER EXPRESSED OR IMPLIED WARRANTIES APPLY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, NON –
INFRINGEMENT OUTSIDE THE U.S. AND FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY DISCLAIMED. Buyer and users assume
all risks of use, handling and storage of the product. Failure to strictly adhere to any recommended procedures shall release ICP from all liability. The
user of the product is responsible to determine suitability of the product for the particular use. The exclusive remedy as to any breach of warranty,
negligence or other claim is limited to the replacement of the product. Liability for any indirect, incidental or consequential damage or loss is specifically
excluded.
