by | Sep 27, 2025
Product Information
Units Test Method Results
pcf ASTM D-1622 11.5 – 12.5
psi ASTM D-1621 150
psi ASTM D-1623 86
psi ASTM D-273 –
psi ASTM C-203 –
% ASTM D-2856 > 94
Units Component A Component B
(A/B) 50 50
(A/B) 52 48
g/mL 1.21 – 1.23 1.07 – 1.09
cPs 150 – 250 500 – 700
– Amber Opaque/Beige-ish
Seconds
Seconds
Seconds
Seconds
Minutes
Hours
Storage and Shelf Life
Packaging
Component A: 500 lbNet Weight
2500 lbNet Weight
Component B: 450 lbNet Weight
2250 lbNet Weight
Non-Warranty: This information is furnished without warranty, expressed or implied, except that is accurate to the best knowledge of Eteco, Inc. The
data on these sheets relates only to the specific material designated herein. Eteco, Inc. assumes no legal responsibility for use or reliance upon
this data. The user should conduct sufficient investigation to establish the suitability of any product for its intended use.
55 gallon steel drum (closed top)
275 gallon plastic totes
55 gallon steel drum (open top)
Gel Time @ 75 F
Rise Time
Tack Free Time
Demold Time
For more information contact Eteco, Inc. (714) 480-1370 | info@etecoinc.com
www.etecoinc.com
Components should be kept well sealed in a dry place from 70 to 90 F. Shelf life of unopened
containers is six (6) months from manufacturing date. Mix Component B well prior to each use. Purge
opened containers with dry nitrogen before resealing. Refer to product SDS for more information.
275 gallon plastic totes
HP 8212
TECHNICAL DATA SHEET
Rigid Foam Polyurethane System
Final Cure Time
45 – 60
80 – 100
90 – 120
90 – 120
10 – 30
24
Mix Ratio by Volume
Mix Ratio by Weight
Viscocity @ 75 F
Color
Cream Time @ 75 F
HP 8212 is a high density rigid polyurethane foam designed for processing through plural component
dispensing equipment. Once fully cured, this material is tough with high compression and tensile value.
HP 8212 exhibits very good surface characteristics. This product is recommended for molding intricate
decorative simulated wood furniture parts, moldings, picture frames and other decorative parts. HP
8212 easily accepts paints and stains. This material is Eco Friendly due to its lack of HCFC`s, HFC`s,
and lead or other heavy metals.
*Properties are typical and not for specifications*
Shear Strength
Handling Characteristics
Tensile Strength
Flexural Strength
Physical Properties (Final Product)
Closed Cell Content
Free Rise Density
Compressive Strength
Specific Gravity @ 75 F
by | Sep 27, 2025
Product Information
Units Test Method Results
pcf ASTM D-1622 5.8 – 6.2
psi ASTM D-1621 80
psi ASTM D-1623 –
psi ASTM D-273 65
% ASTM D-1623 –
% ASTM D-2856 –
Units Component A Component B
(A/B) 50 50
(A/B) 52 48
g/mL 1.21 – 1.23 1.07 – 1.09
cPs 150 – 250 500 – 700
– Amber Opaque/Beige-ish
Seconds
Seconds
Seconds
Seconds
Minutes
Hours
Storage and Shelf Life
Packaging
Component A: 500 lbNet Weight
2500 lbNet Weight
Component B: 450 lbNet Weight
2250 lbNet Weight
Non-Warranty: This information is furnished without warranty, expressed or implied, except that is accurate to the best knowledge of Eteco, Inc. The
data on these sheets relates only to the specific material designated herein. Eteco, Inc. assumes no legal responsibility for use or reliance upon
this data. The user should conduct sufficient investigation to establish the suitability of any product for its intended use.
55 gallon steel drum (closed top)
275 gallon plastic totes
55 gallon steel drum (open top)
Gel Time @ 75 F
Rise Time
Tack Free Time
Demold Time
For more information contact Eteco, Inc. (714) 480-1370 | info@etecoinc.com
www.etecoinc.com
Components should be kept well sealed in a dry place from 70 to 90 F. Shelf life of unopened
containers is six (6) months from manufacturing date. Mix Component B well prior to each use. Purge
opened containers with dry nitrogen before resealing. Refer to product SDS for more information.
275 gallon plastic totes
HP 8206
TECHNICAL DATA SHEET
Rigid Foam Polyurethane System
Final Cure Time
55 – 65
90 – 120
120 – 160
160 – 220
15 – 30
24
Mix Ratio by Volume
Mix Ratio by Weight
Viscocity @ 75 F
Color
Cream Time @ 75 F
HP 8206 is a medium density rigid polyurethane molding foam system designed for processing through
plural component dispensing equipment. Once fully cured, this material is tough with high compression
and tensile value. HP 8206 exhibits very good surface characteristics and excellent moldability. This
product is recommended for molding intricate decorative simulated wood furniture parts, moldings,
picture frames and other decorative parts. This material is Eco Friendly due to its lack of HCFC`s,
HFC`s, and lead or other heavy metals.
*Properties are typical and not for specifications*
Shear Strength
Handling Characteristics
Tensile Strength
Elongation
Physical Properties (Final Product)
Closed Cell Content
Free Rise Density
Compressive Strength
Specific Gravity @ 75 F
by | Sep 27, 2025
Date: 11/27/18
HP 8208
Product Information
Physical Properties (Components)
Component A Component B
Viscocity at 75 F (cps) 160 – 220 500 – 700
Specific Gravity (gr/ml) 1.22 – 1.23 1.07 – 1.09
Physical Properties (Final Product)
Free Rise Density (pcf) 7.7 8.3
Compressive Strength ASTM D-1621 103 psi
Shear Strength ASTM D-273 75 psi
Handling Characteristics
Mix Ratio by Weight (Component A/ Component B) 52 / 48
Mix Ratio by Volume (Component A/ Component B) 50 / 50
Cream Time (at 75
o
F), (seconds) 55 – 65
Rise Time (seconds) 150 – 170
Tack Free Time (seconds) 220 – 240
Demold Time (minutes) 15 – 30
Storage and Shelf Life
Packaging
Component A: 55 gallon steel drum (closed top) 500 lbNet Weight
275 gallons plastic totes 2500 lbNet Weight
Component B: 55 gallon steel drum (closed top) 450 lbNet Weight
275 gallons plastic totes 2250 lbNet Weight
Components A and B should be kept well sealed in a dry place at a temperature between 55 and
90 F. Shelf life of unopened containers is 6 (six) months from a manufacturing date. Purge opened
containers with dry nitrogen before resealing.
Refer to SDS of the product for more information.
Non-Warranty: This information is furnished without warranty, expressed or implied, except that is accurate to the best
knowledge of Eteco, Inc. The data on these sheets relates only to the specific material designated herein. Eteco, Inc.
assumes no legal responsibility for use or reliance upon this data. The user should conduct sufficient investigation to establish
the suitability of any product for its intended use.
HP 8208 is Medium density rigid polyurethane molding foam system designed for processing through
plural component dispensing equipment. This material is Eco Friendly due to no HCFC`s or HFC`s.
This product is recommended for molding intricate decorative simulated wood furniture parts,
moldings, picture frames and other decorative parts. HP 8208 easily accepts paints and stains.
by | Sep 27, 2025
Product Information
Units Test Method Results
pcf ASTM D-1622 5.8 – 6.2
psi ASTM D-1621 80
psi ASTM D-1623 –
psi ASTM D-273 65
% ASTM D-1623 –
% ASTM D-2856 –
Units Component A Component B
(A/B) 50 50
(A/B) 52 48
g/mL 1.21 – 1.23 1.07 – 1.09
cPs 150 – 250 500 – 700
– Amber Opaque/Beige-ish
Seconds
Seconds
Seconds
Seconds
Minutes
Hours
Storage and Shelf Life
Packaging
Component A: 500 lbNet Weight
2500 lbNet Weight
Component B: 450 lbNet Weight
2250 lbNet Weight
Non-Warranty: This information is furnished without warranty, expressed or implied, except that is accurate to the best knowledge of Eteco, Inc. The
data on these sheets relates only to the specific material designated herein. Eteco, Inc. assumes no legal responsibility for use or reliance upon
this data. The user should conduct sufficient investigation to establish the suitability of any product for its intended use.
55 gallon steel drum (closed top)
275 gallon plastic totes
55 gallon steel drum (open top)
Gel Time @ 75 F
Rise Time
Tack Free Time
Demold Time
For more information contact Eteco, Inc. (714) 480-1370 | info@etecoinc.com
www.etecoinc.com
Components should be kept well sealed in a dry place from 70 to 90 F. Shelf life of unopened
containers is six (6) months from manufacturing date. Mix Component B well prior to each use. Purge
opened containers with dry nitrogen before resealing. Refer to product SDS for more information.
275 gallon plastic totes
HP 8206
TECHNICAL DATA SHEET
Rigid Foam Polyurethane System
Final Cure Time
55 – 65
90 – 120
120 – 160
160 – 220
15 – 30
24
Mix Ratio by Volume
Mix Ratio by Weight
Viscocity @ 75 F
Color
Cream Time @ 75 F
HP 8206 is a medium density rigid polyurethane molding foam system designed for processing through
plural component dispensing equipment. Once fully cured, this material is tough with high compression
and tensile value. HP 8206 exhibits very good surface characteristics and excellent moldability. This
product is recommended for molding intricate decorative simulated wood furniture parts, moldings,
picture frames and other decorative parts. This material is Eco Friendly due to its lack of HCFC`s,
HFC`s, and lead or other heavy metals.
*Properties are typical and not for specifications*
Shear Strength
Handling Characteristics
Tensile Strength
Elongation
Physical Properties (Final Product)
Closed Cell Content
Free Rise Density
Compressive Strength
Specific Gravity @ 75 F
by | Sep 27, 2025
Date: 11/27/18
HP 8205
Product Information
Physical Properties (Components)
Component A Component B
Viscocity at 75 F (cps) 160 – 220 500 – 700
Specific Gravity (gr/ml) 1.22 – 1.23 1.07 – 1.09
Physical Properties (Final Product)
Free Rise Density (pcf) 4.8 5.2
Compressive Strength ASTM D-1621 70 psi
Shear Strength ASTM D-273 53 psi
Handling Characteristics
Mix Ratio by Weight (Component A/ Component B) 52 / 48
Mix Ratio by Volume (Component A/ Component B) 50 / 50
Cream Time (at 75
o
F), (seconds) 40 – 50
Rise Time (seconds) 100 – 120
Tack Free Time (seconds) 120 – 160
Demold Time (minutes) 15 – 30
Storage and Shelf Life
Packaging
Component A: 55 gallon steel drum (closed top) 500 lbNet Weight
275 gallons plastic totes 2500 lbNet Weight
Component B: 55 gallon steel drum (closed top) 450 lbNet Weight
275 gallons plastic totes 2250 lbNet Weight
Components A and B should be kept well sealed in a dry place at a temperature between 55 and
90 F. Shelf life of unopened containers is 6 (six) months from a manufacturing date. Purge opened
containers with dry nitrogen before resealing.
Refer to MSDS of the product for more information.
Non-Warranty: This information is furnished without warranty, expressed or implied, except that is accurate to the best
knowledge of Eteco, Inc. The data on these sheets relates only to the specific material designated herein. Eteco, Inc.
assumes no legal responsibility for use or reliance upon this data. The user should conduct sufficient investigation to establish
the suitability of any product for its intended use.
HP 8205 is low density rigid polyurethane molding foam system designed for processing through
plural component dispensing equipment. This material is Eco Friendly, no HCFC`s or HFC`s. This
product is recommended for molding intricate decorative simulated wood furniture parts, moldings,
picture frames and other decorative parts. HP 8205 easily accepts paints and stains.
by | Sep 27, 2025
Date: 11/27/18
HP 8205
Product Information
Physical Properties (Components)
Component A Component B
Viscocity at 75 F (cps) 160 – 220 500 – 700
Specific Gravity (gr/ml) 1.22 – 1.23 1.07 – 1.09
Physical Properties (Final Product)
Free Rise Density (pcf) 4.8 5.2
Compressive Strength ASTM D-1621 70 psi
Shear Strength ASTM D-273 53 psi
Handling Characteristics
Mix Ratio by Weight (Component A/ Component B) 52 / 48
Mix Ratio by Volume (Component A/ Component B) 50 / 50
Cream Time (at 75
o
F), (seconds) 40 – 50
Rise Time (seconds) 100 – 120
Tack Free Time (seconds) 120 – 160
Demold Time (minutes) 15 – 30
Storage and Shelf Life
Packaging
Component A: 55 gallon steel drum (closed top) 500 lbNet Weight
275 gallons plastic totes 2500 lbNet Weight
Component B: 55 gallon steel drum (closed top) 450 lbNet Weight
275 gallons plastic totes 2250 lbNet Weight
Components A and B should be kept well sealed in a dry place at a temperature between 55 and
90 F. Shelf life of unopened containers is 6 (six) months from a manufacturing date. Purge opened
containers with dry nitrogen before resealing.
Refer to MSDS of the product for more information.
Non-Warranty: This information is furnished without warranty, expressed or implied, except that is accurate to the best
knowledge of Eteco, Inc. The data on these sheets relates only to the specific material designated herein. Eteco, Inc.
assumes no legal responsibility for use or reliance upon this data. The user should conduct sufficient investigation to establish
the suitability of any product for its intended use.
HP 8205 is low density rigid polyurethane molding foam system designed for processing through
plural component dispensing equipment. This material is Eco Friendly, no HCFC`s or HFC`s. This
product is recommended for molding intricate decorative simulated wood furniture parts, moldings,
picture frames and other decorative parts. HP 8205 easily accepts paints and stains.
by | Sep 27, 2025
Date: 11/27/18
HP 8205
Product Information
Physical Properties (Components)
Component A Component B
Viscocity at 75 F (cps) 160 – 220 500 – 700
Specific Gravity (gr/ml) 1.22 – 1.23 1.07 – 1.09
Physical Properties (Final Product)
Free Rise Density (pcf) 4.8 5.2
Compressive Strength ASTM D-1621 70 psi
Shear Strength ASTM D-273 53 psi
Handling Characteristics
Mix Ratio by Weight (Component A/ Component B) 52 / 48
Mix Ratio by Volume (Component A/ Component B) 50 / 50
Cream Time (at 75
o
F), (seconds) 40 – 50
Rise Time (seconds) 100 – 120
Tack Free Time (seconds) 120 – 160
Demold Time (minutes) 15 – 30
Storage and Shelf Life
Packaging
Component A: 55 gallon steel drum (closed top) 500 lbNet Weight
275 gallons plastic totes 2500 lbNet Weight
Component B: 55 gallon steel drum (closed top) 450 lbNet Weight
275 gallons plastic totes 2250 lbNet Weight
Components A and B should be kept well sealed in a dry place at a temperature between 55 and
90 F. Shelf life of unopened containers is 6 (six) months from a manufacturing date. Purge opened
containers with dry nitrogen before resealing.
Refer to MSDS of the product for more information.
Non-Warranty: This information is furnished without warranty, expressed or implied, except that is accurate to the best
knowledge of Eteco, Inc. The data on these sheets relates only to the specific material designated herein. Eteco, Inc.
assumes no legal responsibility for use or reliance upon this data. The user should conduct sufficient investigation to establish
the suitability of any product for its intended use.
HP 8205 is low density rigid polyurethane molding foam system designed for processing through
plural component dispensing equipment. This material is Eco Friendly, no HCFC`s or HFC`s. This
product is recommended for molding intricate decorative simulated wood furniture parts, moldings,
picture frames and other decorative parts. HP 8205 easily accepts paints and stains.
by | Sep 27, 2025
Date: 11/27/18
HP 8205
Product Information
Physical Properties (Components)
Component A Component B
Viscocity at 75 F (cps) 160 – 220 500 – 700
Specific Gravity (gr/ml) 1.22 – 1.23 1.07 – 1.09
Physical Properties (Final Product)
Free Rise Density (pcf) 4.8 5.2
Compressive Strength ASTM D-1621 70 psi
Shear Strength ASTM D-273 53 psi
Handling Characteristics
Mix Ratio by Weight (Component A/ Component B) 52 / 48
Mix Ratio by Volume (Component A/ Component B) 50 / 50
Cream Time (at 75
o
F), (seconds) 40 – 50
Rise Time (seconds) 100 – 120
Tack Free Time (seconds) 120 – 160
Demold Time (minutes) 15 – 30
Storage and Shelf Life
Packaging
Component A: 55 gallon steel drum (closed top) 500 lbNet Weight
275 gallons plastic totes 2500 lbNet Weight
Component B: 55 gallon steel drum (closed top) 450 lbNet Weight
275 gallons plastic totes 2250 lbNet Weight
Components A and B should be kept well sealed in a dry place at a temperature between 55 and
90 F. Shelf life of unopened containers is 6 (six) months from a manufacturing date. Purge opened
containers with dry nitrogen before resealing.
Refer to MSDS of the product for more information.
Non-Warranty: This information is furnished without warranty, expressed or implied, except that is accurate to the best
knowledge of Eteco, Inc. The data on these sheets relates only to the specific material designated herein. Eteco, Inc.
assumes no legal responsibility for use or reliance upon this data. The user should conduct sufficient investigation to establish
the suitability of any product for its intended use.
HP 8205 is low density rigid polyurethane molding foam system designed for processing through
plural component dispensing equipment. This material is Eco Friendly, no HCFC`s or HFC`s. This
product is recommended for molding intricate decorative simulated wood furniture parts, moldings,
picture frames and other decorative parts. HP 8205 easily accepts paints and stains.
by | Sep 27, 2025
by | Sep 27, 2025
E’ETECO^.
1000 South Linwood Avenue, Santa Ana, CA 92705
Phone: (714) 480-1370, Fax: (714) 558-1990
Date: 0611012002
Revision: 1111212002
HP 8105
Product lnformation
HP 8105 is a High Performance, rigid polyurethane foam designed for processing through plural
component, low or high pressure dispensing equipment or mixing and pouring by hand. Once fully
cured, this material is tough with high compression and tensile value. HP 8105 exhibits very good
surface characteristics and excellent moldability.
Physical Properties (Components)
Viscosity at 75oF (cps)
Specific Gravity (gr/ml)
Physical Properties (Final Product)
Compression Value (ASTM D – 1621)
Tensile Strength (psi), ASTM D-412
Elongation (%), ASTM D-412
Tear Strength (pli), ASTM D-624, Die C
Handling C haracteristics
Mix Ratio by Weight (A:B):
Mix Ratio by Volume (A:B):
Cream Time (seconds)
GelTime (at 75oF), (seconds)
Rise Time ( seconds)
Tack Free Time (seconds)
Demold Time (minutes)
Final Cure Time (hours)
Density
Component A
200 – 250
1.21 – 1.23
Component B
1000 – 1500
1.08-1.’10
63 psi
90 psi
3%
N/A
52t48
50/50
40-50
90 – 110
110 – 140
170 – 200
10-45
24
4.8 –
5.2
Storage and Shelf Life
Components A and B should be kept well sealed in a dry place at a temperature between 65 and
90oF. Shelf life of unopened containers is six (6) months from manufacturing date. Purge opened
containers with dry nitrogen before resealing. Refer to product MSDS for more information.
Packaging
Component A: 55 gallons steel drum (closed top)
275 gallons plastic bins
55 gallons steel drum (open top)
275 gallons plastic bins
500 lb Net Weight
2500 lb Net Weight
450 lb Net Weight
2250|b Net Weight
Component B
Non-Warranty: This information is furnished without warranty, expressed or implied, except that is accurate to the best
knowledge of Eteco, lnc. The data on these sheets relates only to the specific material designated herein. Eteco, lnc. assumes
no legal responsibility for use or reliance upon this data. The user should conduct sufficient investigation to establish the
suitability of any product for its intended use..
