by | Sep 27, 2025
TC-892 A/B Page 1 of 2 Date: 10/25/2022
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
www.bjbenterprises.com
RIGID POLYURETHANES
By BJB Enterprises. Inc.
An ISO-9001 Certified company
TC-892 A/B
RIGID 80 SHORE D URETHANE CASTING SYSTEM
TC-892 A/B incorporates a non-mercury based catalyst system that produces a tough 80 shore D material with a 20-minute
work time. This system can be used to hand pour large electronic housings, models of all kinds, and point of purchase
items. This system is also available in a 5-minute work time (TC-890), and a 12-minute work time (TC-891).
Non-mercury RoHS compliant
Convenient mixing ratio: 1 to 1 parts by weight Long working time: 20 minutes
Low viscosity, flows easily
Demold time: 5-6 hours at ambient temperature in
a silicone rubber mold (1/8 thick section)
PHYSICAL PROPERTIES TEST METHOD RESULTS
Hardness, Shore D ASTM D2240 80 2
Density (g/cc) ASTM D792 1.14
Cubic Inches per Pound N/A 25
Color/Appearance Visual Off White/Opaque
Tensile Strength (psi) ASTM D638 7,600
Tensile Modulus (psi) ASTM D638 2.4 x 10
5
Elongation (%) ASTM D638 10
Flexural Strength (psi) ASTM D790 10,000
Flexural Modulus (psi) ASTM D790 2.5 x 10
5
Shrinkage (in/in) linear 12 x1/2 x1/2 0.005
Izod Impact, notched (ft-lb/in) ASTM D256 0.7
Heat Deflection Temperature @ 66 psi ASTM D648 195 F (90.6 C)
Heat Deflection Temperature @ 264 psi ASTM D648 177 F (80.6 C)
Note: Reported physical properties based on elevated temperature cured test specimens.
HANDLING PROPERTIES Part A Part B
Mix Ratio by weight 100 100
Mix Ratio by volume 88 100
Specific Gravity @ 77 F (25 C) 1.18 1.04
Color Yellow White
Viscosity (cps) @ 77 F (25 C) Brookfield 325 830
Mixed Viscosity (cps) @ 77 F (25 C) Brookfield 725
Work Time, 100g mass @ 77 F (25 C) 20 minutes
Gel Time 25 minutes
Demold Time @ 77 F (25 C) 5 6 hours
Properties above are typical and not for specifications.
TC-892 A/B Page 2 of 2 Date: 10/25/2022
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
NON-WARRANTY “Except for a warranty that materials substantially comply with the data presented in Manufacturer’s latest bulletin describing the product (the basis for this substantial
compliance is to be determined by the standard quality control tests generally performed by Manufacturer), all materials are sold “AS IS” and without any warranty express or implied as to
merchantability, fitness for a particular purpose, patent, trademark or copyright infringement, or as to any other matter. In no event shall Manufacturer’s liability for damages exceed
Manufacturer’s sale price of the particular quantity with respect to which damages are claimed.”
CURE SCHEDULE/HEAT CURING :
Most of the physical properties can be achieved in 5-7 days at 77 F (25 C). You may use your own post-cure schedule but
the physical properties may vary from BJB s cure schedule of 1-3 hours at 77 F (25 C) followed by 16 hours at 180 F
(82 C). Do not exceed curing temperatures of 200 F (93 C). Support of the part may be required to prevent part
deformation during the heat curing process.
NOTE:
It is advisable whenever possible to evacuate entrapped air prior to casting this system. The use of a de-airing agent can
speed up the process. BJB’s AF-7 antifoam works best as the de-airing agent. In conjunction with these support products
BJB offers pigments in a wide variety of colors and stainless steel mixers called “Jiffy Mixers.” If help is required call BJB
for assistance. For additional information on the use of this product, refer to BJB Guidelines for Handling Polyurethane
Products.
STORAGE:
Store at ambient temperatures, 65-80 F (18-27 C). Unopened containers will have a shelf life of 6 months from date of
shipment when properly stored at recommended temperatures. Purge opened containers with dry nitrogen before re-sealing.
PACKAGING Part A Part B
Cubic Inches
per Kit
Quart Kits 2 lbs. 2 lbs. 100
Gallon Kits 8 lbs. 8 lbs. 400
5-Gallon Kits 40 lbs. 40 lbs. 2,000
SAFETY PRECAUTIONS :
Use in a well-ventilated area. Avoid contact with skin using protective gloves and protective clothing. Repeated or
prolonged contact on the skin may cause an allergic reaction. Eye protection is extremely important. Always use approved
safety glasses or goggles when handling this product.
IF CONTACT OCCURS :
Skin: Immediately wash with soap and water. Remove contaminated clothing and launder before reuse. It is not
recommended to remove resin from skin with solvents. Solvents only increase contact and dry skin. Seek
qualified medical attention if allergic reactions occur.
Eyes: Immediately flush with water for at least 15 minutes. Call a physician.
Ingestion: If swallowed, call a physician immediately. Remove stomach contents by gastric suction or induce vomiting
only as directed by medical personnel. Never give anything by mouth to an unconscious person.
Refer to the Material Safety Data Sheet before using this product.
WARNING: This product can expose you to chemicals including 1,2-Benzenedicarboxylic acid, di-C8-10-branched
alkyl esters, C9-rich, which is known to the State of California to cause cancer. For more information, go to
www.P65Warnings.ca.gov.
Handling Guide
by | Sep 27, 2025
TC-890 A/B Page 1 of 2 Date: 11/01/2022
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
www.bjbenterprises.com
RIGID POLYURETHANES
By BJB Enterprises. Inc.
An ISO-9001 Certified company
TC-890 A/B
RIGID 80 SHORE D URETHANE CASTING SYSTEM
TC-890 A/B incorporates a non-mercury based catalyst system that produces a tough 80 shore D material with a 5-minute
work time. This system can be used to hand pour electronic housings, models of all kinds, and point of purchase items.
This system is also available in a 20-minute work time (TC-892), and a 12-minute work time (TC-891).
Non-mercury RoHS compliant
Convenient mixing ratio: 1 to 1 parts by weight Low viscosity, flows easily
Demold time: 1-2 hours at ambient temperature in
a silicone rubber mold (1/8 thick section)
PHYSICAL PROPERTIES TEST METHOD RESULTS
Hardness, Shore D ASTM D2240 80 2
Density (g/cc) ASTM D792 1.14
Cubic Inches per Pound N/A 25
Color/Appearance Visual Off White/Opaque
Tensile Strength (psi) ASTM D638 7,600
Tensile Modulus (psi) ASTM D638 2.4 x 10
5
Elongation (%) ASTM D638 10
Flexural Strength (psi) ASTM D790 10,000
Flexural Modulus (psi) ASTM D790 2.5 x 10
5
Shrinkage (in/in) linear 12 x1/2 x1/2 0.004
Izod Impact, notched (ft-lb/in) ASTM D256 0.7
Heat Deflection Temperature @ 66 psi ASTM D648 195 F (90.6 C)
Heat Deflection Temperature @ 264 psi ASTM D648 177 F (80.6 C)
Note: Reported physical properties based on elevated temperature cured test specimens.
HANDLING PROPERTIES Part A Part B
Mix Ratio by weight 100 100
Mix Ratio by volume 88 100
Specific Gravity @ 77 F (25 C) 1.18 1.04
Color Yellow White
Viscosity (cps) @ 77 F (25 C) Brookfield 325 830
Mixed Viscosity (cps) @ 77 F (25 C) Brookfield 725
Work Time, 100g mass @ 77 F (25 C) 5 minutes
Gel Time 7 minutes
Demold Time @ 77 F (25 C) 1 2 hours
Properties above are typical and not for specifications.
TC-890 A/B Page 2 of 2 Date: 11/01/2022
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
NON-WARRANTY “Except for a warranty that materials substantially comply with the data presented in Manufacturer’s latest bulletin describing the product (the basis for this substantial
compliance is to be determined by the standard quality control tests generally performed by Manufacturer), all materials are sold “AS IS” and without any warranty express or implied as to
merchantability, fitness for a particular purpose, patent, trademark or copyright infringement, or as to any other matter. In no event shall Manufacturer’s liability for damages exceed
Manufacturer’s sale price of the particular quantity with respect to which damages are claimed.”
IMPORTANT MIXING DIRECTION:
It is important to remix the B components thoroughly prior to each use.
CURE SCHEDULE/HEAT CURING :
Most of the physical properties can be achieved in 5-7 days at 77 F (25 C). You may use your own post-cure schedule but
the physical properties may vary from BJB s cure schedule of 1-3 hours at 77 F (25 C) followed by 16 hours at 180 F
(82 C). Do not exceed curing temperatures of 200 F (93 C). Support of the part may be required to prevent part
deformation during the heat curing process.
NOTE:
It is advisable whenever possible to evacuate entrapped air prior to casting this system. The use of a de-airing agent can
speed up the process. BJB’s AF-7 antifoam works best as the de-airing agent. In conjunction with these support products
BJB offers pigments in a wide variety of colors and stainless steel mixers called “Jiffy Mixers.” If help is required call BJB
for assistance. For additional information on the use of this product, refer to BJB Guidelines for Handling Polyurethane
Products.
STORAGE:
Store at ambient temperatures, 65-80 F (18-27 C). Unopened containers will have a shelf life of 6 months from date of
shipment when properly stored at recommended temperatures. Purge opened containers with dry nitrogen before re-sealing.
PACKAGING Part A Part B
Cubic Inches
per Kit
Quart Kits 2 lbs. 2 lbs. 100
Gallon Kits 8 lbs. 8 lbs. 400
5-Gallon Kits 40 lbs. 40 lbs. 2,000
SAFETY PRECAUTIONS :
Use in a well-ventilated area. Avoid contact with skin using protective gloves and protective clothing. Repeated or
prolonged contact on the skin may cause an allergic reaction. Eye protection is extremely important. Always use approved
safety glasses or goggles when handling this product.
IF CONTACT OCCURS :
Skin: Immediately wash with soap and water. Remove contaminated clothing and launder before reuse. It is not
recommended to remove resin from skin with solvents. Solvents only increase contact and dry skin. Seek
qualified medical attention if allergic reactions occur.
Eyes: Immediately flush with water for at least 15 minutes. Call a physician.
Ingestion: If swallowed, call a physician immediately. Remove stomach contents by gastric suction or induce vomiting
only as directed by medical personnel. Never give anything by mouth to an unconscious person.
Refer to the Material Safety Data Sheet before using this product.
WARNING: This product can expose you to chemicals including 1,2-Benzenedicarboxylic acid, di-C8-10-branched
alkyl esters, C9-rich, which is known to the State of California to cause cancer. For more information, go to
www.P65Warnings.ca.gov.
Handling Guide
by | Sep 27, 2025
TC-890 A/B Page 1 of 2 Date: 11/01/2022
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
www.bjbenterprises.com
RIGID POLYURETHANES
By BJB Enterprises. Inc.
An ISO-9001 Certified company
TC-890 A/B
RIGID 80 SHORE D URETHANE CASTING SYSTEM
TC-890 A/B incorporates a non-mercury based catalyst system that produces a tough 80 shore D material with a 5-minute
work time. This system can be used to hand pour electronic housings, models of all kinds, and point of purchase items.
This system is also available in a 20-minute work time (TC-892), and a 12-minute work time (TC-891).
Non-mercury RoHS compliant
Convenient mixing ratio: 1 to 1 parts by weight Low viscosity, flows easily
Demold time: 1-2 hours at ambient temperature in
a silicone rubber mold (1/8 thick section)
PHYSICAL PROPERTIES TEST METHOD RESULTS
Hardness, Shore D ASTM D2240 80 2
Density (g/cc) ASTM D792 1.14
Cubic Inches per Pound N/A 25
Color/Appearance Visual Off White/Opaque
Tensile Strength (psi) ASTM D638 7,600
Tensile Modulus (psi) ASTM D638 2.4 x 10
5
Elongation (%) ASTM D638 10
Flexural Strength (psi) ASTM D790 10,000
Flexural Modulus (psi) ASTM D790 2.5 x 10
5
Shrinkage (in/in) linear 12 x1/2 x1/2 0.004
Izod Impact, notched (ft-lb/in) ASTM D256 0.7
Heat Deflection Temperature @ 66 psi ASTM D648 195 F (90.6 C)
Heat Deflection Temperature @ 264 psi ASTM D648 177 F (80.6 C)
Note: Reported physical properties based on elevated temperature cured test specimens.
HANDLING PROPERTIES Part A Part B
Mix Ratio by weight 100 100
Mix Ratio by volume 88 100
Specific Gravity @ 77 F (25 C) 1.18 1.04
Color Yellow White
Viscosity (cps) @ 77 F (25 C) Brookfield 325 830
Mixed Viscosity (cps) @ 77 F (25 C) Brookfield 725
Work Time, 100g mass @ 77 F (25 C) 5 minutes
Gel Time 7 minutes
Demold Time @ 77 F (25 C) 1 2 hours
Properties above are typical and not for specifications.
TC-890 A/B Page 2 of 2 Date: 11/01/2022
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
NON-WARRANTY “Except for a warranty that materials substantially comply with the data presented in Manufacturer’s latest bulletin describing the product (the basis for this substantial
compliance is to be determined by the standard quality control tests generally performed by Manufacturer), all materials are sold “AS IS” and without any warranty express or implied as to
merchantability, fitness for a particular purpose, patent, trademark or copyright infringement, or as to any other matter. In no event shall Manufacturer’s liability for damages exceed
Manufacturer’s sale price of the particular quantity with respect to which damages are claimed.”
IMPORTANT MIXING DIRECTION:
It is important to remix the B components thoroughly prior to each use.
CURE SCHEDULE/HEAT CURING :
Most of the physical properties can be achieved in 5-7 days at 77 F (25 C). You may use your own post-cure schedule but
the physical properties may vary from BJB s cure schedule of 1-3 hours at 77 F (25 C) followed by 16 hours at 180 F
(82 C). Do not exceed curing temperatures of 200 F (93 C). Support of the part may be required to prevent part
deformation during the heat curing process.
NOTE:
It is advisable whenever possible to evacuate entrapped air prior to casting this system. The use of a de-airing agent can
speed up the process. BJB’s AF-7 antifoam works best as the de-airing agent. In conjunction with these support products
BJB offers pigments in a wide variety of colors and stainless steel mixers called “Jiffy Mixers.” If help is required call BJB
for assistance. For additional information on the use of this product, refer to BJB Guidelines for Handling Polyurethane
Products.
STORAGE:
Store at ambient temperatures, 65-80 F (18-27 C). Unopened containers will have a shelf life of 6 months from date of
shipment when properly stored at recommended temperatures. Purge opened containers with dry nitrogen before re-sealing.
PACKAGING Part A Part B
Cubic Inches
per Kit
Quart Kits 2 lbs. 2 lbs. 100
Gallon Kits 8 lbs. 8 lbs. 400
5-Gallon Kits 40 lbs. 40 lbs. 2,000
SAFETY PRECAUTIONS :
Use in a well-ventilated area. Avoid contact with skin using protective gloves and protective clothing. Repeated or
prolonged contact on the skin may cause an allergic reaction. Eye protection is extremely important. Always use approved
safety glasses or goggles when handling this product.
IF CONTACT OCCURS :
Skin: Immediately wash with soap and water. Remove contaminated clothing and launder before reuse. It is not
recommended to remove resin from skin with solvents. Solvents only increase contact and dry skin. Seek
qualified medical attention if allergic reactions occur.
Eyes: Immediately flush with water for at least 15 minutes. Call a physician.
Ingestion: If swallowed, call a physician immediately. Remove stomach contents by gastric suction or induce vomiting
only as directed by medical personnel. Never give anything by mouth to an unconscious person.
Refer to the Material Safety Data Sheet before using this product.
WARNING: This product can expose you to chemicals including 1,2-Benzenedicarboxylic acid, di-C8-10-branched
alkyl esters, C9-rich, which is known to the State of California to cause cancer. For more information, go to
www.P65Warnings.ca.gov.
Handling Guide
by | Sep 27, 2025
TC-890 A/B Page 1 of 2 Date: 11/01/2022
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
www.bjbenterprises.com
RIGID POLYURETHANES
By BJB Enterprises. Inc.
An ISO-9001 Certified company
TC-890 A/B
RIGID 80 SHORE D URETHANE CASTING SYSTEM
TC-890 A/B incorporates a non-mercury based catalyst system that produces a tough 80 shore D material with a 5-minute
work time. This system can be used to hand pour electronic housings, models of all kinds, and point of purchase items.
This system is also available in a 20-minute work time (TC-892), and a 12-minute work time (TC-891).
Non-mercury RoHS compliant
Convenient mixing ratio: 1 to 1 parts by weight Low viscosity, flows easily
Demold time: 1-2 hours at ambient temperature in
a silicone rubber mold (1/8 thick section)
PHYSICAL PROPERTIES TEST METHOD RESULTS
Hardness, Shore D ASTM D2240 80 2
Density (g/cc) ASTM D792 1.14
Cubic Inches per Pound N/A 25
Color/Appearance Visual Off White/Opaque
Tensile Strength (psi) ASTM D638 7,600
Tensile Modulus (psi) ASTM D638 2.4 x 10
5
Elongation (%) ASTM D638 10
Flexural Strength (psi) ASTM D790 10,000
Flexural Modulus (psi) ASTM D790 2.5 x 10
5
Shrinkage (in/in) linear 12 x1/2 x1/2 0.004
Izod Impact, notched (ft-lb/in) ASTM D256 0.7
Heat Deflection Temperature @ 66 psi ASTM D648 195 F (90.6 C)
Heat Deflection Temperature @ 264 psi ASTM D648 177 F (80.6 C)
Note: Reported physical properties based on elevated temperature cured test specimens.
HANDLING PROPERTIES Part A Part B
Mix Ratio by weight 100 100
Mix Ratio by volume 88 100
Specific Gravity @ 77 F (25 C) 1.18 1.04
Color Yellow White
Viscosity (cps) @ 77 F (25 C) Brookfield 325 830
Mixed Viscosity (cps) @ 77 F (25 C) Brookfield 725
Work Time, 100g mass @ 77 F (25 C) 5 minutes
Gel Time 7 minutes
Demold Time @ 77 F (25 C) 1 2 hours
Properties above are typical and not for specifications.
TC-890 A/B Page 2 of 2 Date: 11/01/2022
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
NON-WARRANTY “Except for a warranty that materials substantially comply with the data presented in Manufacturer’s latest bulletin describing the product (the basis for this substantial
compliance is to be determined by the standard quality control tests generally performed by Manufacturer), all materials are sold “AS IS” and without any warranty express or implied as to
merchantability, fitness for a particular purpose, patent, trademark or copyright infringement, or as to any other matter. In no event shall Manufacturer’s liability for damages exceed
Manufacturer’s sale price of the particular quantity with respect to which damages are claimed.”
IMPORTANT MIXING DIRECTION:
It is important to remix the B components thoroughly prior to each use.
CURE SCHEDULE/HEAT CURING :
Most of the physical properties can be achieved in 5-7 days at 77 F (25 C). You may use your own post-cure schedule but
the physical properties may vary from BJB s cure schedule of 1-3 hours at 77 F (25 C) followed by 16 hours at 180 F
(82 C). Do not exceed curing temperatures of 200 F (93 C). Support of the part may be required to prevent part
deformation during the heat curing process.
NOTE:
It is advisable whenever possible to evacuate entrapped air prior to casting this system. The use of a de-airing agent can
speed up the process. BJB’s AF-7 antifoam works best as the de-airing agent. In conjunction with these support products
BJB offers pigments in a wide variety of colors and stainless steel mixers called “Jiffy Mixers.” If help is required call BJB
for assistance. For additional information on the use of this product, refer to BJB Guidelines for Handling Polyurethane
Products.
STORAGE:
Store at ambient temperatures, 65-80 F (18-27 C). Unopened containers will have a shelf life of 6 months from date of
shipment when properly stored at recommended temperatures. Purge opened containers with dry nitrogen before re-sealing.
PACKAGING Part A Part B
Cubic Inches
per Kit
Quart Kits 2 lbs. 2 lbs. 100
Gallon Kits 8 lbs. 8 lbs. 400
5-Gallon Kits 40 lbs. 40 lbs. 2,000
SAFETY PRECAUTIONS :
Use in a well-ventilated area. Avoid contact with skin using protective gloves and protective clothing. Repeated or
prolonged contact on the skin may cause an allergic reaction. Eye protection is extremely important. Always use approved
safety glasses or goggles when handling this product.
IF CONTACT OCCURS :
Skin: Immediately wash with soap and water. Remove contaminated clothing and launder before reuse. It is not
recommended to remove resin from skin with solvents. Solvents only increase contact and dry skin. Seek
qualified medical attention if allergic reactions occur.
Eyes: Immediately flush with water for at least 15 minutes. Call a physician.
Ingestion: If swallowed, call a physician immediately. Remove stomach contents by gastric suction or induce vomiting
only as directed by medical personnel. Never give anything by mouth to an unconscious person.
Refer to the Material Safety Data Sheet before using this product.
WARNING: This product can expose you to chemicals including 1,2-Benzenedicarboxylic acid, di-C8-10-branched
alkyl esters, C9-rich, which is known to the State of California to cause cancer. For more information, go to
www.P65Warnings.ca.gov.
Handling Guide
by | Sep 27, 2025
TC-89 A/B PRIMER Page 1 of 2 Date: 04/24/2024
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
www.bjbenterprises.com
PAINTS / COATINGS
By BJB Enterprises. Inc.
An ISO-9001 Certified company
TC-89 PRIMER
This primer was developed to apply against cured urethane substrates for achieving good adhesion when applying another urethane
product for painting or bonding applications.
APPLICATION:
Apply to clean and dry surface to
1
/10 mil or less in thickness. Spraying is the preferred method of applying this primer, however a
light brush or roller coat is adequate in some cases. Drying times will vary with working conditions. At room temperature, the
primer is generally tack free in 45 minutes to 1 hour.
It is recommended that best adhesion results will be gained by applying coatings, casting materials or other materials on the primer
between 45 and 60 minutes after the primer has been applied. Mixed TC-89 A/B should be used within 1 week.
COVERAGE:
1 pint will cover approximately 40 square feet and will provide about mil dry thickness. NOTE: This may vary depending on the
substrate s absorption characteristics.
HANDLING PROPERTIES Part A Part B
Mix Ratio (by weight) 10 100
Specific Gravity @ 77 F (25 C) 1.23 0.81
Color Dark Brown Colorless
Viscosity (cps) @ 77 F (25 C) Brookfield 250 0.61
STORAGE:
Store ambient temperatures, 65-80 F (18-27 C). Unopened containers will have a shelf life of 6 months from date of shipment when
properly stored at recommended temperatures. Purge opened containers with dry nitrogen before re-sealing.
SAFETY PRECAUTIONS:
Use in a well-ventilated area. Avoid contact with skin using protective gloves and protective clothing. Repeated or prolonged
contact on the skin may cause an allergic reaction. Eye protection is extremely important. Always use approved safety glasses or
goggles when handling this product.
TC-89 A/B PRIMER Page 2 of 2 Date: 04/24/2024
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
NON-WARRANTY “Except for a warranty that materials substantially comply with the data presented in Manufacturer’s latest bulletin describing the product (the basis for this substantial
compliance is to be determined by the standard quality control tests generally performed by Manufacturer), all materials are sold “AS IS” and without any warranty express or implied as to
merchantability, fitness for a particular purpose, patent, trademark or copyright infringement, or as to any other matter. In no event shall Manufacturer’s liability for damages exceed
Manufacturer’s sale price of the particular quantity with respect to which damages are claimed.”
IF CONTACT OCCURS:
Skin: Immediately wash with soap and water. Remove contaminated clothing and launder before reuse. It is not
recommended to remove resin from skin with solvents. Solvents only increase contact and dry skin. Seek qualified
medical attention if allergic reactions occur.
Eyes: Immediately flush with water for at least 15 minutes. Call a physician.
Ingestion: If swallowed, call a physician immediately. Remove stomach contents by gastric suction or induce vomiting only as
directed by medical personnel. Never give anything by mouth to an unconscious person.
WARNING: This product can expose you to chemicals including Methyl isobutyl ketone, which is/are known to the State of
California to cause cancer. For more information, go to www.P65Warnings.ca.gov.
NOTE:
Refer to the Safety Data Sheet before using this product. For processing tips and guides, please visit: learn.bjbmaterials.com to
discover additional information.
by | Sep 27, 2025
TC-89 A/B PRIMER Page 1 of 2 Date: 04/24/2024
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
www.bjbenterprises.com
PAINTS / COATINGS
By BJB Enterprises. Inc.
An ISO-9001 Certified company
TC-89 PRIMER
This primer was developed to apply against cured urethane substrates for achieving good adhesion when applying another urethane
product for painting or bonding applications.
APPLICATION:
Apply to clean and dry surface to
1
/10 mil or less in thickness. Spraying is the preferred method of applying this primer, however a
light brush or roller coat is adequate in some cases. Drying times will vary with working conditions. At room temperature, the
primer is generally tack free in 45 minutes to 1 hour.
It is recommended that best adhesion results will be gained by applying coatings, casting materials or other materials on the primer
between 45 and 60 minutes after the primer has been applied. Mixed TC-89 A/B should be used within 1 week.
COVERAGE:
1 pint will cover approximately 40 square feet and will provide about mil dry thickness. NOTE: This may vary depending on the
substrate s absorption characteristics.
HANDLING PROPERTIES Part A Part B
Mix Ratio (by weight) 10 100
Specific Gravity @ 77 F (25 C) 1.23 0.81
Color Dark Brown Colorless
Viscosity (cps) @ 77 F (25 C) Brookfield 250 0.61
STORAGE:
Store ambient temperatures, 65-80 F (18-27 C). Unopened containers will have a shelf life of 6 months from date of shipment when
properly stored at recommended temperatures. Purge opened containers with dry nitrogen before re-sealing.
SAFETY PRECAUTIONS:
Use in a well-ventilated area. Avoid contact with skin using protective gloves and protective clothing. Repeated or prolonged
contact on the skin may cause an allergic reaction. Eye protection is extremely important. Always use approved safety glasses or
goggles when handling this product.
TC-89 A/B PRIMER Page 2 of 2 Date: 04/24/2024
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
NON-WARRANTY “Except for a warranty that materials substantially comply with the data presented in Manufacturer’s latest bulletin describing the product (the basis for this substantial
compliance is to be determined by the standard quality control tests generally performed by Manufacturer), all materials are sold “AS IS” and without any warranty express or implied as to
merchantability, fitness for a particular purpose, patent, trademark or copyright infringement, or as to any other matter. In no event shall Manufacturer’s liability for damages exceed
Manufacturer’s sale price of the particular quantity with respect to which damages are claimed.”
IF CONTACT OCCURS:
Skin: Immediately wash with soap and water. Remove contaminated clothing and launder before reuse. It is not
recommended to remove resin from skin with solvents. Solvents only increase contact and dry skin. Seek qualified
medical attention if allergic reactions occur.
Eyes: Immediately flush with water for at least 15 minutes. Call a physician.
Ingestion: If swallowed, call a physician immediately. Remove stomach contents by gastric suction or induce vomiting only as
directed by medical personnel. Never give anything by mouth to an unconscious person.
WARNING: This product can expose you to chemicals including Methyl isobutyl ketone, which is/are known to the State of
California to cause cancer. For more information, go to www.P65Warnings.ca.gov.
NOTE:
Refer to the Safety Data Sheet before using this product. For processing tips and guides, please visit: learn.bjbmaterials.com to
discover additional information.
by | Sep 27, 2025
TC-886 A/B FR REV 1 Page 1 of 2 Date: 07/03/2023
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
www.bjbenterprises.com
RIGID FR POLYURETHANES
By BJB Enterprises. Inc.
An ISO-9001 Certified company
TC-886 FR REV 1
RIGID 78 SHORE D POLYURETHANE CASTING SYSTEM
FIRE RETARDANT
TC-886 A/B FR REV 1 produces a high impact rigid 78 Shore D material that is commonly used to make computer
housings, models, artwork, electronic component enclosures and all types of parts requiring flame retardant characteristics.
It provides a working time of 15 minutes.
Non-mercury based catalyst system Excellent for vacuum or pressure casting
RoHS/REACH compliant Low viscosity
Three to four hour demold time UL 94 V0 Listed (File# E174527)
PHYSICAL PROPERTIES TEST METHOD RESULTS
Hardness, Shore D ASTM D2240-04e1 78 2
Density (g/cc) ASTM D792-00 1.26
Cubic Inches per Pound N/A 22.6
Color/Appearance Visual Off White/Opaque
Tensile Strength (psi) ASTM D638-03 5,950
Tensile Modulus (psi) ASTM D638-03 224,000
Elongation (%) ASTM D638-03 20
Flexural Strength (psi) ASTM D790-03 9,600
Flexural Modulus (psi) ASTM D790-03 265,000
Shrinkage (in/in) linear 12 x1/2 x1/2 0.0005
Izod Impact, notched (ft-lb/in) ASTM D256-05 0.57
Heat Deflection Temperature @ 66 psi ASTM D648-04 190 F (87.8 C)
Heat Deflection Temperature @ 264 psi ASTM D648-04 173 F (78.3 C)
Dielectric Constant, 1 MHz ASTM D150-87 3.342
Dissipation Factor, 1 MHz ASTM D150-87 0.016
Ball Pressure Test (mm) 167 F (75 C) IEC 60695-10-2 1.2 1.3
Note: Reported physical properties based on elevated temperature cured test specimens.
TC-886 A/B FR REV 1 Page 2 of 2 Date: 07/03/2023
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
NON-WARRANTY “Except for a warranty that materials substantially comply with the data presented in Manufacturer’s latest bulletin describing the product (the basis for this substantial
compliance is to be determined by the standard quality control tests generally performed by Manufacturer), all materials are sold “AS IS” and without any warranty express or implied as to
merchantability, fitness for a particular purpose, patent, trademark or copyright infringement, or as to any other matter. In no event shall Manufacturer’s liability for damages exceed
Manufacturer’s sale price of the particular quantity with respect to which damages are claimed.”
HANDLING PROPERTIES Part A Part B
Mix Ratio by weight 100 85
Mix Ratio by volume 100 68
Specific Gravity @ 77 F (25 C) 1.10 1.38
Color Pale Yellow White
Viscosity (cps) @ 77 F (25 C) Brookfield 75 3,200
Mixed Viscosity (cps) @ 77 F (25 C) Brookfield 310
Work Time, 100g mass @ 77 F (25 C) 15 minutes
Gel Time 18 minutes
Demold Time @ 77 F (25 C) 3 4 hours
Properties above are typical and not for specifications.
CURE SCHEDULE / HEAT CURING:
Most of the physical properties can be achieved in 5-7 days at 77 F (25 C). You may use your own post-cure schedule but the physical
properties may vary from BJB s cure schedule of 1-3 hours at 77 F (25 C) followed by 16 hours at 180 F (82 C). Do not exceed curing
temperatures of 200 F (93 C). Support of the part may be required to prevent part deformation during the heat curing process.
VACUUM DE-GASSING / DE-AIRING:
It is advisable to evacuate entrapped air prior to casting this system. The use of a de-airing agent, (BJB s AF-7) will aid in this process
when either de-airing the combined A/B mixture or when de-airing the A and B components separately.
STORAGE:
Store at ambient temperatures, 65-80 F (18-27 C). Unopened containers will have a shelf life of 6 months from date of shipment when
properly stored at recommended temperatures. Purge opened containers with dry nitrogen before re-sealing.
PACKAGING Part A Part B Cubic Inches per Kit
Quart Kits 2 lbs. 1.7 lbs. 84
Gallon Kits 8 lbs. 6.8 lbs. 335
5-Gallon Kits 40 lbs. 34 lbs. 1,672
SAFETY PRECAUTIONS:
Use in a well-ventilated area. Avoid contact with skin using protective gloves and protective clothing. Repeated or prolonged contact on
the skin may cause an allergic reaction. Eye protection is extremely important. Always use approved safety glasses or goggles when
handling this product.
IF CONTACT OCCURS:
Skin: Immediately wash with soap and water. Remove contaminated clothing and launder before reuse. It is not recommended to
remove resin from skin with solvents. Solvents only increase contact and dry skin. Seek qualified medical attention if
allergic reactions occur.
Eyes: Immediately flush with water for at least 15 minutes. Call a physician.
Ingestion: If swallowed, call a physician immediately. Remove stomach contents by gastric suction or induce vomiting only as directed
by medical personnel. Never give anything by mouth to an unconscious person.
Refer to the Material Safety Data Sheet before using this product.
WARNING: This product can expose you to chemicals including 1,2-Benzenedicarboxylic acid, di-C9-11-branched alkyl esters,
C10-rich, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more
information, go to www.P65Warnings.ca.gov.
Handling Guide
by | Sep 27, 2025
TC-886 A/B FR REV 1 Page 1 of 2 Date: 07/03/2023
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
www.bjbenterprises.com
RIGID FR POLYURETHANES
By BJB Enterprises. Inc.
An ISO-9001 Certified company
TC-886 FR REV 1
RIGID 78 SHORE D POLYURETHANE CASTING SYSTEM
FIRE RETARDANT
TC-886 A/B FR REV 1 produces a high impact rigid 78 Shore D material that is commonly used to make computer
housings, models, artwork, electronic component enclosures and all types of parts requiring flame retardant characteristics.
It provides a working time of 15 minutes.
Non-mercury based catalyst system Excellent for vacuum or pressure casting
RoHS/REACH compliant Low viscosity
Three to four hour demold time UL 94 V0 Listed (File# E174527)
PHYSICAL PROPERTIES TEST METHOD RESULTS
Hardness, Shore D ASTM D2240-04e1 78 2
Density (g/cc) ASTM D792-00 1.26
Cubic Inches per Pound N/A 22.6
Color/Appearance Visual Off White/Opaque
Tensile Strength (psi) ASTM D638-03 5,950
Tensile Modulus (psi) ASTM D638-03 224,000
Elongation (%) ASTM D638-03 20
Flexural Strength (psi) ASTM D790-03 9,600
Flexural Modulus (psi) ASTM D790-03 265,000
Shrinkage (in/in) linear 12 x1/2 x1/2 0.0005
Izod Impact, notched (ft-lb/in) ASTM D256-05 0.57
Heat Deflection Temperature @ 66 psi ASTM D648-04 190 F (87.8 C)
Heat Deflection Temperature @ 264 psi ASTM D648-04 173 F (78.3 C)
Dielectric Constant, 1 MHz ASTM D150-87 3.342
Dissipation Factor, 1 MHz ASTM D150-87 0.016
Ball Pressure Test (mm) 167 F (75 C) IEC 60695-10-2 1.2 1.3
Note: Reported physical properties based on elevated temperature cured test specimens.
TC-886 A/B FR REV 1 Page 2 of 2 Date: 07/03/2023
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
NON-WARRANTY “Except for a warranty that materials substantially comply with the data presented in Manufacturer’s latest bulletin describing the product (the basis for this substantial
compliance is to be determined by the standard quality control tests generally performed by Manufacturer), all materials are sold “AS IS” and without any warranty express or implied as to
merchantability, fitness for a particular purpose, patent, trademark or copyright infringement, or as to any other matter. In no event shall Manufacturer’s liability for damages exceed
Manufacturer’s sale price of the particular quantity with respect to which damages are claimed.”
HANDLING PROPERTIES Part A Part B
Mix Ratio by weight 100 85
Mix Ratio by volume 100 68
Specific Gravity @ 77 F (25 C) 1.10 1.38
Color Pale Yellow White
Viscosity (cps) @ 77 F (25 C) Brookfield 75 3,200
Mixed Viscosity (cps) @ 77 F (25 C) Brookfield 310
Work Time, 100g mass @ 77 F (25 C) 15 minutes
Gel Time 18 minutes
Demold Time @ 77 F (25 C) 3 4 hours
Properties above are typical and not for specifications.
CURE SCHEDULE / HEAT CURING:
Most of the physical properties can be achieved in 5-7 days at 77 F (25 C). You may use your own post-cure schedule but the physical
properties may vary from BJB s cure schedule of 1-3 hours at 77 F (25 C) followed by 16 hours at 180 F (82 C). Do not exceed curing
temperatures of 200 F (93 C). Support of the part may be required to prevent part deformation during the heat curing process.
VACUUM DE-GASSING / DE-AIRING:
It is advisable to evacuate entrapped air prior to casting this system. The use of a de-airing agent, (BJB s AF-7) will aid in this process
when either de-airing the combined A/B mixture or when de-airing the A and B components separately.
STORAGE:
Store at ambient temperatures, 65-80 F (18-27 C). Unopened containers will have a shelf life of 6 months from date of shipment when
properly stored at recommended temperatures. Purge opened containers with dry nitrogen before re-sealing.
PACKAGING Part A Part B Cubic Inches per Kit
Quart Kits 2 lbs. 1.7 lbs. 84
Gallon Kits 8 lbs. 6.8 lbs. 335
5-Gallon Kits 40 lbs. 34 lbs. 1,672
SAFETY PRECAUTIONS:
Use in a well-ventilated area. Avoid contact with skin using protective gloves and protective clothing. Repeated or prolonged contact on
the skin may cause an allergic reaction. Eye protection is extremely important. Always use approved safety glasses or goggles when
handling this product.
IF CONTACT OCCURS:
Skin: Immediately wash with soap and water. Remove contaminated clothing and launder before reuse. It is not recommended to
remove resin from skin with solvents. Solvents only increase contact and dry skin. Seek qualified medical attention if
allergic reactions occur.
Eyes: Immediately flush with water for at least 15 minutes. Call a physician.
Ingestion: If swallowed, call a physician immediately. Remove stomach contents by gastric suction or induce vomiting only as directed
by medical personnel. Never give anything by mouth to an unconscious person.
Refer to the Material Safety Data Sheet before using this product.
WARNING: This product can expose you to chemicals including 1,2-Benzenedicarboxylic acid, di-C9-11-branched alkyl esters,
C10-rich, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more
information, go to www.P65Warnings.ca.gov.
Handling Guide
by | Sep 27, 2025
TC-872 A/B Page 1 of 2 Date: 06/29/2020
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
www.bjbenterprises.com
TC-872 A/B
RIGID 70 SHORE D HIGH HEAT RESISTANT
POLYURETHANE CASTING SYSTEM
TC-872 A/B is a RoHS compliant, non-mercury based catalyst polyurethane system that produces a tough 70 shore D
material. This system has an exceptionally high impact and a high heat deflection temperature which in some cases can be
post cured without having to use fixtures.
High heat resistance High Impact
Non-mercury RoHS/REACH compliant
Working time of 10-12 minutes
PHYSICAL PROPERTIES TEST METHOD TEST RESULTS
Hardness, Shore D ASTM D2240-04e1 70 2
Density (g/cc) ASTM D792-00 1.13
Cubic Inches per Pound N/A 25.5
Color/Appearance Visual Translucent Pale Yellow
Tensile Strength (psi) ASTM D638-03 3,310
Tensile Modulus (psi) ASTM D638-03 71,350
Elongation (%) ASTM D638-03 28.3
Flexural Strength (psi) ASTM D790-03 3,315
Flexural Modulus (psi) ASTM D790-03 84,680
Shrinkage (in/in) linear 12 x x 0.004
Izod Impact, notched (ft-lb/in) ASTM D256-05 1.78
Heat Deflection Temperature @ 66 psi ASTM D648-04 240 F (115.6 C)
Note: Reported physicals based on elevated temperature cured test specimens.
HANDLING PROPERTIES Part A Part B
Mix Ratio (by weight) 100 35
Mix Ratio (by volume) 100 32
Specific Gravity @ 77 F (25 C) 1.06 1.16
Color Colorless Amber
Viscosity (cps) @ 77 F (25 C) Brookfield 830 650
Mixed Viscosity (cps) @ 77 F (25 C) Brookfield 750
Work Time, 100g mass @ 77 F (25 C) 10 12 minutes
Gel Time 13 15 minutes
Demold Time @ 77 F (25 C) 2 3 hours
Properties above are typical and not for specifications.
RIGID FILLED & UNFILLED URETHANES
Dedicated to QUALITY, SERVICE, SAFETY, and INNOVATION
An ISO-9001 Certified company
TC-872 A/B Page 2 of 2 Date: 06/29/2020
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
NON-WARRANTY “Except for a warranty that materials substantially comply with the data presented in Manufacturer’s latest bulletin describing the product (the basis for this substantial
compliance is to be determined by the standard quality control tests generally performed by Manufacturer), all materials are sold “AS IS” and without any warranty express or implied as to
merchantability, fitness for a particular purpose, patent, trademark or copyright infringement, or as to any other matter. In no event shall Manufacturer’s liability for damages exceed
Manufacturer’s sale price of the particular quantity with respect to which damages are claimed.”
CURE SCHEDULE/HEAT CURING:
Most of the physical properties can be achieved in 5-7 days at 77 F (25 C). You may use your own post-cure schedule but
the physical properties may vary from BJB s cure schedule of 1-3 hours at 77 F (25 C) followed by 16 hours at 180 F
(82 C). Do not exceed curing temperatures of 200 F (93 C). Support of the part may be required to prevent part
deformation during the heat curing process.
NOTE #1:
Important: Shake or re-blend both A and B components separately prior to weighing and combining. It is
advisable whenever possible to evacuate entrapped air prior to casting this system. The use of a de-airing agent can speed
up the process. BJB s AF-4 antifoam works best as the de-airing agent. In conjunction with these support products BJB
offers pigments in a wide variety of colors and stainless steel mixers called Jiffy Mixers . For additional information on
the use of this product, refer to BJB Guidelines for Handling Polyurethane Products. If further information is required,
please call BJB s technical staff for assistance.
NOTE #2:
The natural color of TC-872 A/B is a translucent pale yellow. When the cured material is exposed to direct sunlight or
strong UV light, the material will turn to an amber/orange color within approximately 2 hours.
STORAGE:
Store at ambient temperatures, 65-80 F (18-27 C). Unopened containers will have a shelf life of 6 months from date of
shipment when properly stored at recommended temperatures. Purge opened containers with dry nitrogen before re-
sealing.
PACKAGING Part A Part B
Cubic Inches
per Kit
Quart Kits 2 lbs. 0.7 lb. 69
Gallon Kits 8 lbs. 2.8 lbs. 275
5-Gallon Kits 40 lbs. 14 lbs. 1,377
55-Gallon Drum Kits 400 lbs. 140 lbs. 13,770
SAFETY PRECAUTIONS:
Use in a well-ventilated area. Avoid contact with skin using protective gloves and protective clothing. Repeated or
prolonged contact on the skin may cause an allergic reaction. Eye protection is extremely important. Always use approved
safety glasses or goggles when handling this product.
IF CONTACT OCCURS:
Skin: Immediately wash with soap and water. Remove contaminated clothing and launder before reuse. It is not
recommended to remove resin from skin with solvents. Solvents only increase contact and dry skin. Seek qualified
medical attention if allergic reactions occur.
Eyes: Immediately flush with water for at least 15 minutes. Call a physician.
Ingestion: If swallowed, call a physician immediately. Remove stomach contents by gastric suction or induce vomiting
only as directed by medical personnel. Never give anything by mouth to an unconscious person.
Refer to the Material Safety Data Sheet before using this product.
WARNING: This product can expose you to chemicals including Toluene diisocyanate, which are known to the State of
California to cause cancer. For more information, go to www.P65Warnings.ca.gov.
Handling Guide
by | Sep 27, 2025
TC-872 A/B Page 1 of 2 Date: 06/29/2020
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
www.bjbenterprises.com
TC-872 A/B
RIGID 70 SHORE D HIGH HEAT RESISTANT
POLYURETHANE CASTING SYSTEM
TC-872 A/B is a RoHS compliant, non-mercury based catalyst polyurethane system that produces a tough 70 shore D
material. This system has an exceptionally high impact and a high heat deflection temperature which in some cases can be
post cured without having to use fixtures.
High heat resistance High Impact
Non-mercury RoHS/REACH compliant
Working time of 10-12 minutes
PHYSICAL PROPERTIES TEST METHOD TEST RESULTS
Hardness, Shore D ASTM D2240-04e1 70 2
Density (g/cc) ASTM D792-00 1.13
Cubic Inches per Pound N/A 25.5
Color/Appearance Visual Translucent Pale Yellow
Tensile Strength (psi) ASTM D638-03 3,310
Tensile Modulus (psi) ASTM D638-03 71,350
Elongation (%) ASTM D638-03 28.3
Flexural Strength (psi) ASTM D790-03 3,315
Flexural Modulus (psi) ASTM D790-03 84,680
Shrinkage (in/in) linear 12 x x 0.004
Izod Impact, notched (ft-lb/in) ASTM D256-05 1.78
Heat Deflection Temperature @ 66 psi ASTM D648-04 240 F (115.6 C)
Note: Reported physicals based on elevated temperature cured test specimens.
HANDLING PROPERTIES Part A Part B
Mix Ratio (by weight) 100 35
Mix Ratio (by volume) 100 32
Specific Gravity @ 77 F (25 C) 1.06 1.16
Color Colorless Amber
Viscosity (cps) @ 77 F (25 C) Brookfield 830 650
Mixed Viscosity (cps) @ 77 F (25 C) Brookfield 750
Work Time, 100g mass @ 77 F (25 C) 10 12 minutes
Gel Time 13 15 minutes
Demold Time @ 77 F (25 C) 2 3 hours
Properties above are typical and not for specifications.
RIGID FILLED & UNFILLED URETHANES
Dedicated to QUALITY, SERVICE, SAFETY, and INNOVATION
An ISO-9001 Certified company
TC-872 A/B Page 2 of 2 Date: 06/29/2020
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
NON-WARRANTY “Except for a warranty that materials substantially comply with the data presented in Manufacturer’s latest bulletin describing the product (the basis for this substantial
compliance is to be determined by the standard quality control tests generally performed by Manufacturer), all materials are sold “AS IS” and without any warranty express or implied as to
merchantability, fitness for a particular purpose, patent, trademark or copyright infringement, or as to any other matter. In no event shall Manufacturer’s liability for damages exceed
Manufacturer’s sale price of the particular quantity with respect to which damages are claimed.”
CURE SCHEDULE/HEAT CURING:
Most of the physical properties can be achieved in 5-7 days at 77 F (25 C). You may use your own post-cure schedule but
the physical properties may vary from BJB s cure schedule of 1-3 hours at 77 F (25 C) followed by 16 hours at 180 F
(82 C). Do not exceed curing temperatures of 200 F (93 C). Support of the part may be required to prevent part
deformation during the heat curing process.
NOTE #1:
Important: Shake or re-blend both A and B components separately prior to weighing and combining. It is
advisable whenever possible to evacuate entrapped air prior to casting this system. The use of a de-airing agent can speed
up the process. BJB s AF-4 antifoam works best as the de-airing agent. In conjunction with these support products BJB
offers pigments in a wide variety of colors and stainless steel mixers called Jiffy Mixers . For additional information on
the use of this product, refer to BJB Guidelines for Handling Polyurethane Products. If further information is required,
please call BJB s technical staff for assistance.
NOTE #2:
The natural color of TC-872 A/B is a translucent pale yellow. When the cured material is exposed to direct sunlight or
strong UV light, the material will turn to an amber/orange color within approximately 2 hours.
STORAGE:
Store at ambient temperatures, 65-80 F (18-27 C). Unopened containers will have a shelf life of 6 months from date of
shipment when properly stored at recommended temperatures. Purge opened containers with dry nitrogen before re-
sealing.
PACKAGING Part A Part B
Cubic Inches
per Kit
Quart Kits 2 lbs. 0.7 lb. 69
Gallon Kits 8 lbs. 2.8 lbs. 275
5-Gallon Kits 40 lbs. 14 lbs. 1,377
55-Gallon Drum Kits 400 lbs. 140 lbs. 13,770
SAFETY PRECAUTIONS:
Use in a well-ventilated area. Avoid contact with skin using protective gloves and protective clothing. Repeated or
prolonged contact on the skin may cause an allergic reaction. Eye protection is extremely important. Always use approved
safety glasses or goggles when handling this product.
IF CONTACT OCCURS:
Skin: Immediately wash with soap and water. Remove contaminated clothing and launder before reuse. It is not
recommended to remove resin from skin with solvents. Solvents only increase contact and dry skin. Seek qualified
medical attention if allergic reactions occur.
Eyes: Immediately flush with water for at least 15 minutes. Call a physician.
Ingestion: If swallowed, call a physician immediately. Remove stomach contents by gastric suction or induce vomiting
only as directed by medical personnel. Never give anything by mouth to an unconscious person.
Refer to the Material Safety Data Sheet before using this product.
WARNING: This product can expose you to chemicals including Toluene diisocyanate, which are known to the State of
California to cause cancer. For more information, go to www.P65Warnings.ca.gov.
Handling Guide
