30R937U-10_SDS.pdf

by | Sep 27, 2025

30R7524423A_SDS.pdf

by | Sep 27, 2025

30R736AP40D_SDS.pdf

by | Sep 27, 2025

Polyester Resin Solution
Product name
Product type
Section 1. Identification
Chemical family Aromatic.
Relevant identified uses of the substance or mixture and uses advised against
SDS No. NA-1803:4785 (Version: 2.0)
Uses advised against
Identified uses Used in the manufacture of thermoset plastic parts.
No additional information.
R736-APD-40
SAFETY DATA SHEET
Date of issue: 08/15/2018
Date of previous issue: 03/09/2018
Emergency telephone number
Supplier’s details
CHEMTREC Within USA and Canada
CHEMTREC Outside USA and Canada
CANUTEC Within Canada
+1 (800) 424-9300
+1 (703) 527-3887
+1 (613) 996-6666
CCN1023
AOC, LLC
955 Highway 57 East
Collierville, TN 38017
Phone Number: (901) 854-2800
Hours: 8AM-5pm (Central Time) Mon-Fri
AOC, LLC
38 Royal Road
Guelpha, Ontario Canada N1H 1G3
Phone Number: (519) 821-5180
Hours: 8am-5pm (Eastern) Mon-Fri
E-Mail: aoc.sds@aoc-resins.com
Website: www.aoc-resins.com
United States: Canada:
Section 2. Hazards identification
OSHA/HCS status
FLAMMABLE LIQUIDS Category 3 H226
SKIN CORROSION/IRRITATION Category 2 H315
SERIOUS EYE DAMAGE/ EYE IRRITATION Category 2 H319
ACUTE TOXICITY (INHALATION) Category 4 H332
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) Category 3 H335
REPRODUCTIVE TOXICITY Category 2 H361d
CARCINOGENICITY Category 2 H351
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) Category 1 H372
ASPIRATION HAZARD Category 1 H304
Classification of the substance or mixture
Signal word
Danger
Hazard statements
H226: Flammable liquid and vapor.
H332: Harmful if inhaled.
H361d: Suspected of damaging the unborn child.
H351: Suspected of causing cancer.
H319: Causes serious eye irritation.
H315: Causes skin irritation.
H335: May cause respiratory irritation.
H372: Causes damage to organs through prolonged or repeated exposure if inhaled.
H304: May be fatal if swallowed and enters airways.
Hazard pictograms
Precautionary statements
GHS label elements
General
This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).
Page: 1 of 9Date of issue: 08/15/2018 Date of previous issue: 03/09/2018 NA-1803:4785 (Version: 2.0)

R736-APD-40
Section 2. Hazards identification
Prevention
P210: Keep away from heat, sparks, open flames and hot surfaces. – No smoking.
P233: Keep container tightly closed.
P240: Ground/bond container and receiving equipment.
P241: Use explosion-proof electrical/ventilating/lighting/material-handling equipment.
P242: Use only non-sparking tools.
P243: Take precautionary measures against static discharge.
P201: Obtain special instructions before use.
P202: Do not handle until all safety precautions have been read and understood.
P264: Wash hands thoroughly after handling.
P270: Do not eat, drink or smoke when using this product.
P271: Use only outdoors or in a well-ventilated area.
P280: Wear protective gloves/protective clothing/eye protection/face protection.
P260: Do not breathe vapor or mist.
Response
P370+P378: In case of fire: Use dry chemical, CO , water spray (fog) or foam.
P301+P310: IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.
P331: Do NOT induce vomiting.
P308+P313: IF exposed or concerned: Get medical advice/attention.
P304+P340: IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
P312: Call a POISON CENTER or physician if you feel unwell.
P303+P361+P353: IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower.
P332+P313: If skin irritation occurs, get medical advice/attention.
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.
Continue rinsing.
P337+P313: If eye irritation persists, get medical advice/attention.
P308+P311: IF exposed or concerned: Call a POISON CENTER or doctor/physician.
P391: Collect spillage.
Storage
P403 + P235: Store in a well-ventilated place. Keep cool.
P233: Keep container tightly closed.
P405: Store locked up.
Disposal
P501: Dispose of contents and container in accordance with all local, regional, national and international regulations.
P101: If medical advice is needed, have product container or label at hand.
P102: Keep out of reach of children.
Hazards not otherwise classified
None known.
Section 3. Composition/information on ingredients
Ingredient name CAS number %
There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are
classified as hazardous to health or the environment and hence require reporting in this section.
Substance/mixture
Occupational exposure limits, if available, are listed in Section 8.
Mixture.
styrene 100-42-5 43.0
Section 4. First aid measures
Immediately flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Use of buffered baby
shampoo will aid in removal. If irritation persists, get medical attention.
In case of contact, immediately flush skin with plenty of water. Remove contaminated clothing and shoes. If irritation persists, seek
medical attention. Wash contaminated clothing before reuse. Clean shoes thoroughly before reuse.
Move the victim to a safe area as soon as possible. Allow the victim to rest in a well-ventilated area. If breathing is difficult, give oxygen.
If the victim is not breathing, perform mouth-to-mouth resuscitation. Seek immediate medical attention.
Eye contact
Skin contact
Inhalation
Description of necessary first aid measures
Page: 2 of 9Date of issue: 08/15/2018 Date of previous issue: 03/09/2018 NA-1803:4785 (Version: 2.0)

R736-APD-40
Section 4. First aid measures
Wash out mouth with water. Remove dentures if any. Stop if the exposed person feels sick as vomiting may be dangerous. Do not
induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit does not
enter the lungs. Seek immediate medical attention.
Ingestion
Notes to physician
Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled.
Most important symptoms/effects, acute and delayed
See toxicological information (Section 11)
Indication of immediate medical attention and special treatment needed, if necessary
Irritating to mouth, throat and stomach.
Causes serious eye irritation.
Causes skin irritation.
Harmful if inhaled. May cause respiratory irritation.
Eye contact
Skin contact
Inhalation
Ingestion
Over-exposure signs/symptoms
Eye contact
Inhalation
Skin contact
Ingestion
Adverse symptoms may include the following: pain or irritation, watering, redness.
Adverse symptoms may include the following: respiratory tract irritation, coughing.
Adverse symptoms may include the following: irritation, redness.
Adverse symptoms may include the following: Irritating to mouth, throat and stomach..
Section 5. Fire-fighting measures
Fire water contaminated with this material must be contained and prevented from being discharged to any waterway, sewer or drain.
Hazardous thermal decomposition products
Specific hazards arising from the chemical
Decomposition products may include the following materials: carbon dioxide, carbon monoxide, sulfur oxides halogenated compounds,
metal oxide/oxides
Flammable liquid and vapor. In a fire or if heated, a pressure increase will occur and the container may burst, with the risk of a
subsequent explosion. The vapor/gas is heavier than air and will spread along the ground. Vapors may accumulate in low or confined
areas or travel a considerable distance to a source of ignition and flash back. Runoff to sewer may create fire or explosion hazard. This
material is harmful to aquatic life with long lasting effects. Fire water contaminated with this material must be contained and prevented
from being discharged to any waterway, sewer or drain.
Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated
in positive pressure mode.
Special protective equipment for fire-fighters
Use dry chemical, CO , water spray (fog) or foam.
Extinguishing media
Do not use water jet.
Suitable extinguishing media
Unsuitable extinguishing media
Special protective actions for fire-fighters
Page: 3 of 9Date of issue: 08/15/2018 Date of previous issue: 03/09/2018 NA-1803:4785 (Version: 2.0)

R736-APD-40
Section 6. Accidental release measures
Environmental precautions
Personal precautions, protective equipment and emergency procedures
Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water courses,
basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and collect spillage with non-
combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local
regulations (see Section 13). Use spark-proof tools and explosion-proof equipment. Dispose of via a licensed waste disposal contractor.
Contaminated absorbent material may pose the same hazard as the spilled product. Note: see Section 1 for emergency contact
information and Section 13 for waste disposal.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the
product has caused environmental pollution (sewers, waterways, soil or air). Water polluting material. May be harmful to the environment
if released in large quantities.
Stop leak if without risk. Move containers from spill area. Dilute with water and mop up if water-soluble. Alternatively, or if water-insoluble,
absorb with an inert dry material and place in an appropriate waste disposal container. Use spark-proof tools and explosion-proof
equipment. Dispose of via a licensed waste disposal contractor.
Methods and materials for containment and cleaning up
For non-emergency personnel
For emergency responders
No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Do not touch or walk
through spilled material. Shut off all ignition sources. No flares, smoking or flames in hazard area. Avoid breathing vapor or mist.
Provide adequate ventilation.
If specialised clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials.
Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment. See also the information in
“For non-emergency personnel”.
Small spill
Large spill
Section 7. Handling and storage
Advice on general occupational hygiene
Conditions for safe storage, including any incompatibilities
Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash
hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating
areas. See also Section 8 for additional information on hygiene measures.
Store in accordance with local regulations. Store in a segregated and approved area. Store in original container protected from direct
sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Eliminate all
ignition sources. Segregate from oxidizing materials. Keep container tightly closed and sealed until ready for use. Containers that have
been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate
containment to avoid environmental contamination. Refer to the product label and/or technical data sheet for further information.
Protective measures
Put on appropriate personal protective equipment (see Section 8). Eating, drinking and smoking should be prohibited in areas where this
material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove
contaminated clothing and protective equipment before entering eating areas. Do not breathe vapor or mist. Do not ingest. Avoid contact
with eyes, skin and clothing. Avoid release to the environment. Use only with adequate ventilation. Wear appropriate respirator when
ventilation is inadequate. Do not enter storage areas and confined spaces unless adequately ventilated. Keep in the original container or
an approved alternative made from a compatible material, kept tightly closed when not in use. Store and use away from heat, sparks,
open flame or any other ignition source. Use only non-sparking tools. Take precautionary measures against electrostatic discharges.
Empty containers retain product residue and can be hazardous. Do not reuse container.
Precautions for safe handling
Section 8. Exposure controls/personal protection
Control parameters
Occupational exposure limits
Page: 4 of 9Date of issue: 08/15/2018 Date of previous issue: 03/09/2018 NA-1803:4785 (Version: 2.0)

R736-APD-40
Section 8. Exposure controls/personal protection
styrene ACGIH TLV (United States, 3/2017). Absorbed through skin.
TWA: 20 ppm 8 hours.
TWA: 85 mg/m 8 hours.
STEL: 40 ppm 15 minutes.
STEL: 170 mg/m 15 minutes.
OSHA PEL Z2 (United States, 2/2013).
TWA: 100 ppm 8 hours.
CEIL: 200 ppm
AMP: 600 ppm 5 minutes.
NIOSH REL (United States, 10/2016).
TWA: 50 ppm 10 hours.
TWA: 215 mg/m 10 hours.
STEL: 100 ppm 15 minutes.
STEL: 425 mg/m 15 minutes.
Ingredient name Exposure limits
Hand protection
Use a properly fitted, air-purifying or air-fed respirator complying with an approved standard if a risk assessment indicates this is
necessary. Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the safe working
limits of the selected respirator.
Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products
if a risk assessment indicates this is necessary.
Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid
exposure to liquid splashes, mists or dusts.
Eye/face protection
Respiratory protection
Body protection
Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be
approved by a specialist before handling this product.
Appropriate engineering controls
Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or other engineering controls to keep worker
exposure to airborne contaminants below any recommended or statutory limits. The engineering controls also need to keep gas, vapor or
dust concentrations below any lower explosive limits. Use explosion-proof ventilation equipment.
Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end
of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Ensure that eyewash stations
and safety showers are close to the workstation location.
Hygiene measures
Individual protection measures
Other skin protection
Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks
involved and should be approved by a specialist before handling this product.
Section 9. Physical and chemical properties
Physical state
Melting point
Vapor pressure
Vapor density
Liquid.
23.8 F / 30.6 C (Styrene)
3.6 (Air = 1) (Styrene )
5.0 mm Hg@ 68 F / 20 C (Styrene)
Aromatic.Odor
pH
Amber.Color
Evaporation rate < 1 (Butyl acetate = 1) Flash point 88 F / 31 C (Styrene) Not applicable. 0.01 - 0.1 ppm (Styrene)Odor threshold Appearance Boiling point 293 F / 145 C (Styrene) Flammability (solid, gas) Not applicable. Lower and upper explosive (flammable) limits Lower: 1.1% Upper: 6.1% (Styrene) Page: 5 of 9Date of issue: 08/15/2018 Date of previous issue: 03/09/2018 NA-1803:4785 (Version: 2.0) R736-APD-40 Section 9. Physical and chemical properties Relative density Solubility 1.1 (Water = 1) Slight. Auto-ignition temperature 914 F / 490 C (Styrene) Not available. Viscosity Not available. Partition coefficient: n-octanol/water Molecular weight 1,000 to 15,000 Decomposition temperature Not available. Section 10. Stability and reactivity Hazardous decomposition products Conditions to avoid Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld, braze, solder, drill, grind or expose containers to heat or sources of ignition. Under normal conditions of storage and use, hazardous decomposition products should not be produced. The product is stable. Stable under recommended storage and handling conditions (see Section 7). Chemical stability Reactive or incompatible with the following materials: oxidizing materials Incompatible materials Possibility of hazardous reactions Under normal conditions of storage and use, hazardous reactions will not occur. Reactivity No specific test data related to reactivity available for this product or its ingredients. Section 11. Toxicological information Acute toxicity styrene LC50 Inhalation Gas. Rat 2770 ppm 4 hours LC50 Inhalation Vapor Rat 11800 mg/m 4 hours LC50 Inhalation Vapor Rat 5634.2 ppm 4 hours LD50 Oral Rat 2650 mg/kg - Ingredient name Result Species Dose Exposure Carcinogenicity Mutagenicity Irritation/Corrosion styrene Eyes - Mild irritant Human - 50 parts per million - Eyes - Moderate irritant Rabbit - 24 hours 100 milligrams - Eyes - Severe irritant Rabbit - 100 milligrams- Skin - Mild irritant Rabbit - 500 milligrams- Skin - Moderate irritant Rabbit - 100 Percent - Ingredient name Result Score Exposure Observation Sensitization Species Information on toxicological effects Classification styrene - 2A Reasonably anticipated to be a human carcinogen. Ingredient name NTPIARCACGIH May cause sensitization by skin contact. No mutagenic effect. 1) Negative Study A published study concluded that the mechanism for producing cancer in mice exposed to styrene is not applicable in human metabolism. (June 2013 Pharmacology & Toxicology 66 (2013)) 2) Negative Study A recent update to an extensive study of reinforced plastic workers from 1948-1977 concluded that there was no coherent evidence that styrene exposure increased risk of cancer (March 2013 Epidemiology Vol. 24 Issue 2) 3) Positive Study Styrene induced pulmonary toxicity and carcinogenicity in mice was shown to be caused by a metabolite of styrene, probably styrene oxide. (Dec.2001 Toxicology Vol.169 Issue 2) Page: 6 of 9Date of issue: 08/15/2018 Date of previous issue: 03/09/2018 NA-1803:4785 (Version: 2.0) R736-APD-40 Section 11. Toxicological information Teratogenicity Reproductive toxicity Inhalation Harmful if inhaled. May cause respiratory irritation. Irritating to mouth, throat and stomach. Ingestion Skin contact Causes skin irritation. Causes serious eye irritation. Eye contact Symptoms related to the physical, chemical and toxicological characteristics Skin contact Ingestion Adverse symptoms may include the following: respiratory tract irritation, coughing. Adverse symptoms may include the following: Irritating to mouth, throat and stomach.. Adverse symptoms may include the following: irritation, redness. Eye contact Adverse symptoms may include the following: pain or irritation, watering, redness. Specific target organ toxicity (single exposure) Specific target organ toxicity (repeated exposure) Aspiration hazard Potential acute health effects Not considered to be toxic to the reproductive system. No known effect according to our database. No known effect according to our database. A study of long term effects of workers exposed to styrene levels in the range of 25-35 ppm, 8 hour TWA, indicated a possible mild hearing loss. No known effect according to our database. Inhalation Section 12. Ecological information LogPow BCF Potential Bioaccumulative potential Other adverse effects No known effect according to our database. styrene 0.35 13.49 low Toxicity styrene Acute EC50 1400 g/l Fresh water Algae - Pseudokirchneriella subcapitata 72 hours Acute EC50 720 g/l Fresh water Algae - Pseudokirchneriella subcapitata 96 hours Acute EC50 4700 g/l Fresh water Daphnia - Daphnia magna 48 hours Acute LC50 52 mg/l Marine water Crustaceans - Artemia salina 48 hours Acute LC50 4020 g/l Fresh water Fish - Pimephales promelas 96 hours Chronic NOEC 63 g/l Fresh water Algae - Pseudokirchneriella subcapitata 96 hours Ingredient name SpeciesResult Exposure Persistence and degradability Soil/water partition coefficient (KOC) Not available. Mobility in soil Not available. Ingredient name Page: 7 of 9Date of issue: 08/15/2018 Date of previous issue: 03/09/2018 NA-1803:4785 (Version: 2.0) R736-APD-40 Section 13. Disposal considerations The generation of waste should be avoided or minimized wherever possible. Empty containers or liners may retain some product residues. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Disposal of this product, solutions and any by- products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Avoid disposal. Attempt to use product completely in accordance with intended use. Waste packaging should be recycled. Incineration or landfill should only be considered when recycling is not feasible. Disposal methods The information in this section contains generic advice and guidance. The list of Identified Uses in Section 1 should be consulted for any available use-specific information provided in the Exposure Scenario(s). Special precautions This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers that have not been cleaned or rinsed out. Empty containers or liners may retain some product residues. Do not cut, weld or grind used containers unless they have been cleaned thoroughly internally. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Section 14. Transport information Resin Solution 3 III UN1866UN number Proper shipping name Transport hazard class(es) Packing group DOT / TDG/ IMDG/IMO / ICAO/IATA and National regulations. Additional information US regulations require the reporting of spills when the amount exceeds the Reportable Quantity (RQ) for specific components of this material. See CERCLA in Section 15, Regulatory Information, for the Reportable Quantities. Environmental hazards Marine pollutant: No. Special precautions for user Transport within user s premises: always transport in closed containers that are upright and secure. Ensure that persons transporting the product know what to do in the event of an accident or spillage. IMDGEmergency schedules (EmS): F-E, S-E Remarks: FP-31 C IATANo additional information. Section 15. Regulatory information International regulations lists All components are listed or exempted. SARA 313 SARA 311/312 United States inventory (TSCA 8b) Australia (AICS) All components are listed or exempted. Canada (DSL) All components are listed or exempted. China (IECSC) All components are listed or exempted. Europe (EINECS) Not determined. Japan Japan inventory (ENCS): Not determined. Japan inventory (ISHL): Not determined. Republic of Korea (KECI) All components are listed or exempted. Malaysia (EHS Register) Not determined. New Zealand (NZIoC) All components are listed or exempted. Philippines (PICCS) All components are listed or exempted. Taiwan (CSNN) All components are listed or exempted. Per the June 13, 2016 Federal Register notice, EPA harmonized the EPCRA 311/312 hazard categories with the 2012 OSHA hazard communication standard for classifying and labeling of chemicals (i.e. GHS). Please refer to Section 2 of the SDS to identify the appropriate hazard categories for reporting purposes. U.S. Federal regulations Page: 8 of 9Date of issue: 08/15/2018 Date of previous issue: 03/09/2018 NA-1803:4785 (Version: 2.0) R736-APD-40 Section 15. Regulatory information Ingredient name styrene 100-42-5 Form R - Reporting requirements CAS number California Prop. 65 State regulations styrene - 1000 lbs. (453.6 kg)CERCLA RQ - WARNING: This product can expose you to chemicals including Styrene, which is known to the State of California to cause cancer, and Methanol, which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov. Section 16. Other information History Version Prepared by The information contained in this data sheet is furnished in good faith and without warranty, representation, or inducement or license of any kind, except that it is accurate to the best of AOC, LLC's knowledge, or was obtained from sources believed by AOC, LLC to be reliable. The accuracy, adequacy or completeness of health and safety precautions set forth herein cannot be guaranteed, and the buyer is solely responsible for ensuring that the product is used, handled, stored, and disposed of safely and in compliance with applicable federal, state or provincial, and local laws. AOC, LLC disclaims liability for any loss, damage or personal injury that arises from, or is in any way related to, use of the information contained in this data sheet. Notice to reader Date of previous issue Indicates information that has changed from previously issued version. Key to abbreviations ATE = Acute Toxicity Estimate BCF = Bioconcentration Factor GHS = Globally Harmonized System of Classification and Labelling of Chemicals IATA = International Air Transport Association IBC = Intermediate Bulk Container IMDG = International Maritime Dangerous Goods LogPow = logarithm of the octanol/water partition coefficient MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution) UN = United Nations 08/15/2018 03/09/2018 2.0 National Fire Protection Association (U.S.A.) Reprinted with permission from NFPA 704-2001, Identification of the Hazards of Materials for Emergency Response Copyright 1997, National Fire Protection Association, Quincy, MA 02269. This reprinted material is not the complete and official position of the National Fire Protection Association, on the referenced subject which is represented only by the standard in its entirety. Copyright 2001, National Fire Protection Association, Quincy, MA 02269. This warning system is intended to be interpreted and applied only by properly trained individuals to identify fire, health and reactivity hazards of chemicals. The user is referred to certain limited number of chemicals with recommended classifications in NFPA 49 and NFPA 325, which would be used as a guideline only. Whether the chemicals are classified by NFPA or not, anyone using the 704 systems to classify chemicals does so at their own risk. AOC Corporate Regulatory Affairs This Safety Data Sheet (SDS) and its content are the confidential and proprietary information of AOC and it may not be modified, altered, deconstructed, or presented in any other manner, without the explicit authorization of AOC and/or its legal counsel. 1 3 2 Health Special Instability Flammability Date of issue Page: 9 of 9Date of issue: 08/15/2018 Date of previous issue: 03/09/2018 NA-1803:4785 (Version: 2.0)

30R6631T_SDS.pdf

by | Sep 27, 2025

SAFETY DATA SHEET
Revision Date: 05/Jan/2015
1. IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKING
Product Identifier
Product Description:
DION 6631-20 (TAP Isophthalic High-Strength)
Other means of identification
SAP ID(s): 6379 ; 6380; 196441; 200056
Material Code: 6631-20
Chemical Family Polyester Resin
Recommended use of the chemical and restrictions on use
Intended Use: Corrosion Resistant Resin
Uses advised against No information available
Details of the supplier of the safety data sheet
2. HAZARDS IDENTIFICATION
Classification
OSHA Regulatory Status
This chemical is considered hazardous by the 2012 OSHA Hazard Communication Standard (29 CFR 1910.1200)
Acute toxicity – Inhalation (Vapors) Category 4
Skin corrosion/irritation Category 2
Serious eye damage/eye irritation Category 2A
Carcinogenicity Sub-category 1B
Reproductive toxicity Category 2
Specific target organ toxicity (single exposure) Category 3
Specific target organ toxicity (repeated exposure) Category 1
Chronic aquatic toxicity Category 3
Label elements
Emergency Overview Statements
Manufacturer/Supplier:
Reichhold LLC 2
Corporate Headquarters
P.O. Box 13582
Research Triangle Park, NC 27709
USA
Tel +1-919-990-7500
Fax +1-919-767-8602
Flammable liquids Category 3
Danger
__________________________________________________________________________________________
Hazard Statements
Harmful if inhaled
Causes skin irritation
Causes serious eye irritation
May cause cancer
Suspected of damaging fertility or the unborn child
May cause respiratory irritation
Causes damage to hearing through prolonged or repeated exposure if inhaled
Harmful to aquatic life with long lasting effects
Flammable liquid and vapor
Page 1 / 11
Emergency Telephone (Chemtrec) 1-800-424-9300
E-mail address prodsafety@reichhold.com

__________________________________________________________________________________________
6379 ; DION 6631-20 Revision Date: 05/Jan/2015
Precautionary Statements – Prevention
Obtain special instructions before use
Do not handle until all safety precautions have been read and understood
Use personal protective equipment as required
Use only outdoors or in a well-ventilated area
Wash face, hands and any exposed skin thoroughly after handling
Wear protective gloves/protective clothing/eye protection/face protection
Do not breathe mist, vapors, spray
Do not eat, drink or smoke when using this product
Keep away from heat/sparks/open flames/hot surfaces. – No smoking
Keep container tightly closed
Ground/bond container and receiving equipment
Use explosion-proof electrical/ventilating/lighting equipment
Use only non-sparking tools
Take precautionary measures against static discharge
Keep cool
Avoid release to the environment
Precautionary Statements – Response
IF exposed or concerned: Get medical advice/attention
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing
If eye irritation persists: Get medical advice/attention
If skin irritation occurs: Get medical advice/attention
IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower
Wash contaminated clothing before reuse
IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing
In case of fire: Use CO2, dry chemical, or foam to extinguish
Precautionary Statements – Storage
Store in a well-ventilated place. Keep container tightly closed
Precautionary Statements – Disposal
Dispose of contents/container to industrial incineration plant
Dispose of in accordance with federal, state and local regulations
Hazards not otherwise classified (HNOC)
Other Information
Unknown acute toxicity 54.0% of the mixture consists of ingredient(s) of unknown toxicity.
Unknown aquatic toxicity 54.1% of the mixture consists of components(s) of unknown hazards to the aquatic
environment.
3. COMPOSITION/INFORMATION ON INGREDIENTS
Component CAS No Weight-% Trade Secret
Polyester Resin Proprietary 53.6
Styrene 100-42-5 45.4
Cobalt Compounds Proprietary < 0.25 * __________________________________________________________________________________________ Page 2 / 11 Appearance Pink Physical State Liquid Odor Pungent __________________________________________________________________________________________ 6379 ; DION 6631-20 Revision Date: 05/Jan/2015 * The exact percentage (concentration) of composition has been withheld as a trade secret. If CAS number is "proprietary", the specific chemical identity has been withheld as a trade secret. 4. FIRST AID MEASURES First Aid Measures Eye Contact Immediately flush eyes for at least 15 minutes. Get medical attention. Skin Contact Wash off with warm water and soap. Remove contaminated clothing and shoes. If skin irritation persists, call a physician. Wash contaminated clothing before reuse. Inhalation Remove person to fresh air. If signs/symptoms continue, get medical attention. Keep patient warm and at rest. If not breathing, give artificial respiration. If breathing is labored, administer oxygen. Get medical attention immediately. Ingestion Do not induce vomiting. Potential for aspiration if swallowed. This material may enter the lungs during vomiting. Never give anything by mouth to an unconscious person. GET IMMEDIATE MEDICAL ATTENTION. Most important symptoms and effects, both acute and delayed Most Important Symptoms and Effects No information available. Indication of any immediate medical attention and special treatment needed Notes to Physician Treat symptomatically. 5. FIRE-FIGHTING MEASURES Suitable Extinguishing Media Carbon dioxide (CO2), Foam, Dry chemical, Water spray Unsuitable Extinguishing Media Do not use a solid water stream as it may scatter and spread fire. Specific hazards arising from the chemical Hazardous combustion products Combustion may produce carbon monoxide, carbon dioxide and irritating or toxic vapors and gases Combustion/Explosion Hazards Flammable. Vapors may form explosive mixture with air. Flash back possible over considerable distance. This material may polymerize (react) when its container is exposed to heat (as during a fire). This polymerization increases pressure inside a closed container and may result in the violent rupture of the container. Empty containers may retain product residue (liquid and/or vapor). Do not pressurize, cut, weld, braze, solder, drill, grind, or expose these containers to heat, flame, sparks, static electricity, or other sources of ignition as the container may explode and may cause injury or death. __________________________________________________________________________________________ Protective Equipment and Precautions for Firefighters: Wear self-contained breathing apparatus (SCBA) and full fire-fighting protective clothing. Thoroughly decontaminate all protective equipment after use. Evacuate all persons from the fire area to a safe location. Move non-burning material, as feasible, to a safe location as soon as possible. Fire fighters should be protected from potential explosion hazard while extinguishing the blaze. DO NOT extinguish a fire resulting from the flow of this flammable liquid until the flow of liquid is effectively shut off. This precaution will help prevent the accumulation of an explosive vapor-air mixture after the initial fire is extinguished. Use water spray to cool fire-exposed containers. Page 3 / 11 6. ACCIDENTAL RELEASE MEASURES Personal precautions, protective equipment and emergency procedures __________________________________________________________________________________________ 6379 ; DION 6631-20 Revision Date: 05/Jan/2015 Personal Precautions Remove all sources of ignition. Evacuate personnel to safe areas. Avoid contact with skin and eyes. Use personal protective equipment as required. Ensure adequate ventilation. Keep people away from and upwind of spill/leak. Beware of vapors accumulating to form explosive concentrations. Vapors can accumulate in low areas. Other Information All equipment used when handling the product must be grounded. Environmental Precautions Environmental Precautions Prevent further leakage or spillage if safe to do so. Do not allow material to contaminate ground water system. Prevent product from entering drains. Soak up with inert absorbent material and dispose of as hazardous waste. Beware of vapors accumulating to form explosive concentrations. Vapors can accumulate in low areas. Methods and material for containment and cleaning up Methods for Containment Prevent spilled material from 1) contaminating soil, 2) entering sanitary sewers, storm sewers, and drainage systems, and 3) entering bodies of water or ditches that lead to waterways. Prevent spreading over a wide area (e.g. by containment or oil barriers). Methods for Clean-up Soak up with inert absorbent material. Remove from surface water (e.g. by skimming or siphoning). Dispose of contaminated material as waste according to item 13. 7. HANDLING AND STORAGE Precautions for Safe Handling Handling Do not breathe vapor or mist. Avoid contact with eyes, skin and clothing. Take off contaminated clothing and wash before reuse. Ensure adequate ventilation. Ground and bond containers when transferring material. Use spark-proof tools and explosion-proof equipment. Consult your supplier of promoters and catalysts for additional instructions on proper mixing and usage. Empty containers may retain product residue (liquid and/or vapor). Do not pressurize, cut, weld, braze, solder, drill, grind, or expose these containers to heat, flame, sparks, static electricity, or other sources of ignition as the container may explode and may cause injury or death. Empty drums should be completely drained and properly bunged. Empty drums should be promptly returned to a drum reconditioner or properly disposed. Do not use compressed air for filling, discharging or handling. Wash hands before breaks and immediately after handling the product. Conditions for safe storage, including any incompatibilities Storage Keep away from heat and sources of ignition. No smoking. Keep away from direct sunlight. Keep containers tightly closed in a cool, well-ventilated place. To ensure maximum stability and maintain optimum resin properties, resins should be stored in closed containers at temperatures below 77 F (25 C). 8. EXPOSURE CONTROLS/PERSONAL PROTECTION Exposure limits Components with workplace control parameters Styrene (CAS #: 100-42-5) ACGIH TLV 20 ppm TWA 40 ppm STEL A4 Not Classifiable as a Human Carcinogen __________________________________________________________________________________________ OSHA PEL Page 4 / 11 100 ppm TWA 200 ppm Ceiling Industry PEL While the federal workplace exposure limit for styrene is 100 ppm, OSHA accepted the styrene industry's proposal to voluntarily meet a PEL of 50 ppm on an 8 hour TWA and a Short Term Exposure Limit (STEL) of 100 ppm, 15 minute exposure. __________________________________________________________________________________________ 6379 ; DION 6631-20 Revision Date: 05/Jan/2015 Canada - Alberta OELs 40 ppm STEL 170 mg/m 3 STEL 20 ppm TWA 85 mg/m 3 TWA Canada - Ontario OELs 35 ppm TWA 100 ppm STEL Canada - British Columbia OELs 50 ppm TWA 75 ppm STEL NIOSH IDLH 700 ppm Immediately dangerous to life or health IDLH Mexico OEL 100 ppm STEL 425 mg/m 3 STEL 50 ppm TWA 215 mg/m 3 TWA (skin) Legend ACGIH (American Conference of Governmental Industrial Hygienists) TLV (Threshold Limit Value) TWA (time-weighted average) STEL - Short Term Exposure Limit OSHA - Occupational Safety and Health Administration PEL - Permissible Exposure Limit OEL - Occupational Exposure Limit NIOSH - National Institute for Occupational Safety and Health IDLH - Immediately Dangerous to Life or Health SKIN: Skin Absorption Appropriate engineering controls Engineering Controls Use general ventilation to maintain airborne concentrations to levels that are below regulatory and recommended occupational exposure limits. Local ventilation may be required during certain operations. Use explosion-proof equipment. Individual protection measures, such as personal protective equipment Eye/face Protection Safety glasses with side-shields. If splashes are likely to occur:. Tight sealing safety goggles. Ensure that eyewash stations and safety showers are close to the workstation location. Skin Protection : H D U S U R W H F W L Y H Q L W U L O H U X E E H U R U 9 L W R Q J O R Y H V * O R Y H V P D G H R I Q L W U L O H U X E E H U R U S R O Y L Q O chloride (PVC) may be used for splash protection and brief or intermittent contact with styrenated polyester resin. Please observe the instructions regarding permeability and breakthrough time which are provided by the supplier of the gloves. Also take into consideration the specific local conditions under which the product is used, such as the danger of cuts, abrasion. Impervious clothing. Rubber or plastic boots. Respiratory Protection None required if hazards have been assessed and airborne concentrations are maintained below the exposure limits listed in Section 8. Wear an approved air-purifying respirator with organic vapor cartridges and particulate filters where airborne concentrations may exceed exposure limits in Section 8 and/or there is exposure to dust or mists due to sanding, grinding, cutting, or spraying. Use an approved positive-pressure air-supplied respirator with emergency escape provisions if there is any potential for an uncontrolled release, airborne concentrations are not known, or any other circumstances where air-purifying respirators may not provide adequate protection General Hygiene Considerations Handle in accordance with good industrial hygiene and safety practice. 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance Pink Odor Pungent __________________________________________________________________________________________ Odor Threshold 0.2 ppm (Styrene) Page 5 / 11 Physical State Liquid pH Not applicable __________________________________________________________________________________________ 6379 ; DION 6631-20 Revision Date: 05/Jan/2015 Flash Point 32 C / 89 F Flash Point Method: Seta closed cup Autoignition Temperature 490 C / 914 F (Styrene) Boiling point / boiling range 146 C / 295 F (Styrene) Melting point / Freezing point No information available Flammability Limit in Air Lower 1.1% (Styrene) Upper 6.1% (Styrene) Specific Gravity 1.035 - 1.078 @ 25 C Solubility Insoluble (Water) Evaporation Rate 0.49 (BuAc = 1) (Styrene) Vapor Pressure 5 mmHg @ 20 C (Styrene) 6.7 hPa (Styrene) Vapor Density 3.6 (Air = 1) (Styrene) Explosive Properties No information available Oxidizing Properties No information available Percent Volatile, wt.% 44.5 - 47.5 % by weight VOC Content: 480 g/l (calculated) product as supplied Viscosity 500 - 700 cps @ 25 C Partition Coefficient (n-octanol/water) No information available Decomposition temperature No information available 10. STABILITY AND REACTIVITY Reactivity Chemical Stability Stable under normal conditions. Stable under recommended storage conditions. Possibility of Hazardous Reactions Hazardous Polymerization Polymerization can occur. Hazardous polymerization will occur if contaminated with peroxides, metal salts and polymerization catalysts. Hazardous polymerization may occur upon depletion of inhibitor - may cause heat and pressure build-up in closed containers. Product will undergo hazardous polymerization at temperatures above 150 F (65 C). Conditions to Avoid Heat, flames and sparks. Contamination by those materials referred to under Incompatible materials. Unstable upon depletion of inhibitor. Elevated temperatures. Incompatible materials Strong acids. Strong oxidizing agents. Metal salts. Polymerization catalysts. Hazardous Decomposition Products Hydrocarbons. Carbon monoxide. Carbon dioxide (CO2). Thermal decomposition can lead to release of irritating and toxic gases and vapors. 11. TOXICOLOGICAL INFORMATION Information on likely routes of exposure Primary Routes of Entry Eye contact, Ingestion, Inhalation, Skin Contact, Skin absorption Acute toxicity Styrene Oral LD50 = 5000 mg/kg (Rat) Dermal LD50 > 2000 mg/kg (Rat)
Inhalation LC50 = 11.8 mg/l (4 H) (Rat)
Cobalt Compounds
__________________________________________________________________________________________
Oral LD50
Page 6 / 11
= 3900 mg/kg (Rat)
No dangerous reaction known under conditions of normal use.

__________________________________________________________________________________________
6379 ; DION 6631-20 Revision Date: 05/Jan/2015
Information on toxicological effects
Symptoms Symptoms of overexposure may be headache, dizziness, tiredness, nausea and vomiting.
Delayed and immediate effects as well as chronic effects from short and long-term exposure
Eyes Irritating to eyes.
Skin Harmful by skin absorption. Contact causes skin irritation. Prolonged skin contact may defat
the skin and produce dermatitis.
Inhalation Harmful by inhalation. May cause irritation of respiratory tract. Inhalation of high vapor
concentrations can cause CNS-depression and narcosis.
Ingestion Harmful if swallowed. Ingestion may cause gastrointestinal irritation, nausea, vomiting and
diarrhea. Aspiration hazard if swallowed – can enter lungs and cause damage. Ingestion is
not an anticipated route of exposure for this material in industrial use.
Sensitization Not sensitizing.
Repeated dose toxicity In humans, styrene may cause a transient decrease in color discrimination and effects on
hearing. Repeated or prolonged exposure may cause skin irritation and dermatitis, due to
defatting properties of the product. May cause damage to the liver, eyes, brain, respiratory
system, central nervous system through prolonged or repeated exposure if inhaled. May
cause damage to the kidneys, liver, eyes, brain, respiratory system, central nervous system
through prolonged or repeated exposure if inhaled.
Mutagenic effects Styrene has given mixed positive and negative results in a number of mutagenicity tests.
Styrene was not mutagenic without metabolic activation but gave negative and positive
mutagenic results with metabolic activation.
Carcinogenicity .
Styrene
ACGIH Group A4 – Not classifiable as a human carcinogen.
IARC Group 2B – Possibly Carcinogenic to Humans
NTP Reasonably anticipated to be human carcinogen
Cobalt Compounds
IARC Group 2B – Possibly Carcinogenic to Humans
Legend IARC – International Agency for Research on Cancer NTP – National Toxicology Program
Reproductive Toxicity No information available.
Neurological Effects No information available.
STOT – single exposure No information available.
STOT – repeated exposure No information available.
Target organ(s) Liver, Central nervous system (CNS), Respiratory system, Kidney.
Aspiration Hazard No information available.
Numerical measures of toxicity – Product Information
Unknown acute toxicity 54.0% of the mixture consists of ingredient(s) of unknown toxicity.
The following values are calculated based on chapter 3.1 of the GHS document .
ATEmix (oral) 5066 mg/kg
__________________________________________________________________________________________
ATEmix (dermal)
Page 7 / 11
2027 mg/kg
ATEmix (inhalation-vapor) 12 mg/L

__________________________________________________________________________________________
6379 ; DION 6631-20 Revision Date: 05/Jan/2015
12. ECOLOGICAL INFORMATION
Ecotoxicity
Styrene
Log Kow 2.95
Bioconcentration factor (BCF)74
Algae EC50 = 1.4 mg/L (Pseudokirchneriella subcapitata) (72h)
EC50 0.46 – 4.3 mg/L (Pseudokirchneriella subcapitata) (72h)
Fish LC50 3.24 – 4.99 mg/L (Pimephales promelas) (96 h) flow-through
LC50 19.03 – 33.53 mg/L (Lepomis macrochirus) (96 h) static
LC50 6.75 – 14.5 mg/L (Pimephales promelas) (96 h) static
LC50 58.75 – 95.32 mg/L (Poecilia reticulata) (96 h) static
Water Flea EC50 3.3 – 7.4 mg/L 48 h
Unknown aquatic toxicity
54.1% of the mixture consists of components(s) of unknown hazards to the aquatic environment.
Persistence/Degradability
No information available. Bioaccumulation
No information available.
Other adverse effects
No information available.
13. DISPOSAL CONSIDERATIONS
Waste treatment methods
Disposal Considerations Hazardous waste. Can be incinerated, when in compliance with local regulations.
Contaminated packaging Empty containers should be taken for local recycling, recovery or waste disposal.
US EPA Waste Number D001 (IGNITABLE): When discarded in its purchased form, this material would be regulated
under 40 CFR 261.21 as EPA Hazardous Waste Number D001 based on the characteristic
of ignitability.
14. TRANSPORT INFORMATION
DOT
UN-No UN1866
Proper Shipping Name RESIN SOLUTION
Hazard Class 3
Packing Group III
NAERG: 127
TDG
UN-No UN1866
Proper Shipping Name RESIN SOLUTION
Hazard Class CLASS 3
Packing Group PG III
NAERG: 127
MEX
__________________________________________________________________________________________
UN-No
Page 8 / 11
UN1866
Proper Shipping Name RESIN SOLUTION

__________________________________________________________________________________________
6379 ; DION 6631-20 Revision Date: 05/Jan/2015
Hazard Class CLASS 3
Packing Group PG III
NAERG: 127
IATA
UN-No UN1866
Proper Shipping Name RESIN SOLUTION
Hazard Class 3
Packing Group III
Packing Instructions 355; 366
NAERG: 127
IMDG/IMO
UN-No UN1866
Proper Shipping Name RESIN SOLUTION
Hazard Class CLASS 3
Packing Group PG III
EmS-No F-E, S-E
NAERG: 127
15. REGULATORY INFORMATION
International Inventories
TSCA Inventory Status: All components of this material are listed on the US Toxic Substances Control Act (TSCA)
inventory.
Canadian Inventory Status: All components of this material are listed on the Canadian Domestic Substances List (DSL)
Australian Inventory Status:This product contains only chemicals which are currently listed on the Australian Inventory
of Chemical Substances
Korean Inventory Status: This product contains only chemicals which are currently listed on the Korean Chemical
Substances List
Philippine Inventory: This product contains only chemicals that are currently listed on the Philippine Inventory of
Chemicals and Chemical Substances
Japan ENCS: This product contains only chemicals that are currently listed on the Japanese Inventory of
Existing and New Chemical Substances
Chinese IECS: This product contains one or more chemicals currently not on the Chinese Inventory of
Existing Chemical Substances
New Zealand Inventory: This product contains only chemicals which are currently listed on the New Zealand
Inventory of Chemicals
US Federal Regulations
TSCA 12(b) – Export Notification:
This material does not contain any components that are subject to the US Toxic Substances Control Act (TSCA) Section 12(b)
Export Notification requirements.
SARA 313
Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA). This product contains a chemical
or chemicals which are subject to the reporting requirements of the Act and and Title 40 of the Code of Federal Regulations, Part
372:
Component CAS No Weight-% SARA 313 Status
Styrene 100-42-5 45.4 Listed
SARA 311/312 Hazardous Categorization
__________________________________________________________________________________________
Acute Health Hazard
Page 9 / 11
Yes
Chronic Health Hazard Yes

__________________________________________________________________________________________
6379 ; DION 6631-20 Revision Date: 05/Jan/2015
Fire Hazard Yes
Sudden Release of Pressure Hazard No
Reactive Hazard Yes
Clean Water Act
This product contains the following listed substances:
Component CWA – Reportable
Quantities
CWA – Toxic Pollutants CWA – Priority
Pollutants
CWA – Hazardous
Substances
Styrene
100-42-5
1000 lb Listed
Clean Air Act, Section 112 Hazardous Air Pollutants (HAPs) (see 40 CFR 61)
This product contains the following HAPs:
Component CAS No Weight-% HAPS data
Styrene 100-42-5 45.4
CERCLA
This product contains the following reportable quantities:
Component 40 CFR 302.4 RQ 40 CFR 355 EHS TPQs
Styrene 1000 lb
454 kg
Chemical Weapons Convention (CWC)
This product contains a Schedule 3 Toxic chemical precursor.
State Regulations
California Proposition 65
WARNING: This material contains a chemical known to the State of California to cause cancer and birth defects or other
reproductive harm. The California Safe Drinking Water and Toxic Enforcement Act of 1986 requires that clear and reasonable
warning be given prior to exposing any person to this chemical.
Canada
This product has been classified in accordance with the hazard criteria of the Controlled Products Regulations (CPR) and the
MSDS contains all the information required by the CPR.
16. OTHER INFORMATION
Prepared By Reichhold Product Regulatory Department Phone Number: 919-990-7500
Revision Date: 05/Jan/2015
Revision Summary: This data sheet contains changes from the previous version in section(s): 2, 3, 4, 5, 9, 11, 14
Former date: 5 July 2012
__________________________________________________________________________________________
This information is provided in good faith and is correct to the best of Reichhold’s knowledge as of the date hereof and is designed
to assist our customers; however, Reichhold makes no representation as to its completeness or accuracy. Our products are
intended for sale to industrial and commercial customers. We require customers to inspect and test our products before use and to
satisfy themselves as to suitability for their specific applications. Any use which Reichhold customers or third parties make of this
information, or any reliance on, or decisions made based upon it, are the responsibility of such customer or third party. Reichhold
disclaims responsibility for damages, or liability, of any kind resulting from the use of this information. THERE ARE NO
WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, INCLUDING THOSE OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE WITH RESPECT TO THIS INFORMATION OR TO THE PRODUCT IT DESCRIBES. IN NO
EVENT SHALL REICHHOLD BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
Page 10 / 11
NFPA Rating Health 2 Flammability 3 Instability 1

__________________________________________________________________________________________
6379 ; DION 6631-20 Revision Date: 05/Jan/2015
__________________________________________________________________________________________
End of Safety Data Sheet
Page 11 / 11

30R32737_SDS.pdf

by | Sep 27, 2025

SAFETY DATA SHEET
Revision Date 04/Sep/2018
1. IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKING
Product identifier
Product Description:
POLYLITE 32737-00
Other means of identification
SAP ID(s): 5654 ; 5655
Material Code: 32737-00
Chemical Family Polyester Resin
Recommended use of the chemical and restrictions on use
Recommended Use Surface Casting Resin
Uses advised against No information available
Details of the supplier of the safety data sheet
Emergency Telephone Chemtrec: 1-800-424-9300 (in U.S. & Canada)
+1-703-741-5970 (international)
E-mail address MSDS@polynt.com
2. HAZARDS IDENTIFICATION
Classification
OSHA Regulatory Status
This chemical is considered hazardous by the 2012 OSHA Hazard Communication Standard (29 CFR 1910.1200)
Acute toxicity – Inhalation (Vapors) Category 4
Skin corrosion/irritation Category 2
Serious eye damage/eye irritation Category 2A
Skin sensitization Category 1
Carcinogenicity Sub-category 1B
Reproductive toxicity Category 2
Specific target organ toxicity (single exposure) Category 3
Specific target organ toxicity (repeated exposure) Category 1
Chronic aquatic toxicity Category 3
Label elements
Emergency Overview
Manufacturer/Supplier:
Polynt Composites USA, Inc.
99 East Cottage Avenue
Carpentersville IL 60110
In Canada
Polynt Composites Canada Inc
29 Regan Road
Brampton, Ontario
L7A 1B2
Flammable liquids Category 3
Danger
_____________________________________________________________________________________________
Page 1 / 10
Hazard statements
Harmful if inhaled
Causes skin irritation
Causes serious eye irritation
May cause an allergic skin reaction
May cause cancer

_____________________________________________________________________________________________
5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018
Precautionary Statements – Prevention
Obtain special instructions before use
Do not handle until all safety precautions have been read and understood
Use personal protective equipment as required
Use only outdoors or in a well-ventilated area
Wash face, hands and any exposed skin thoroughly after handling
Contaminated work clothing should not be allowed out of the workplace
Wear protective gloves/protective clothing/eye protection/face protection
Do not breathe mist, vapors, spray
Do not eat, drink or smoke when using this product
Keep away from heat/sparks/open flames/hot surfaces. – No smoking
Keep container tightly closed
Ground/bond container and receiving equipment
Use explosion-proof electrical/ ventilating/ lighting/ equipment
Use only non-sparking tools
Take precautionary measures against static discharge
Keep cool
Avoid release to the environment
Precautionary Statements – Response
IF exposed or concerned: Get medical advice/attention
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing
If eye irritation persists: Get medical advice/attention
If skin irritation or rash occurs: Get medical advice/attention
IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower
IF ON SKIN: Wash with plenty of soap and water
Wash contaminated clothing before reuse
If skin irritation occurs: Get medical advice/attention
IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing
In case of fire: Use CO2, dry chemical, or foam to extinguish
Precautionary Statements – Storage
Store in a well-ventilated place. Keep container tightly closed
Precautionary Statements – Disposal
Dispose of contents/container to industrial incineration plant
Dispose of in accordance with federal, state and local regulations
Hazards not otherwise classified (HNOC)
Not applicable
Other Information
None known
Unknown acute toxicity 61.1 % of the mixture consists of ingredient(s) of unknown toxicity
Unknown aquatic toxicity 61.2 % of the mixture consists of components(s) of unknown hazards to the aquatic
environment
Suspected of damaging fertility or the unborn child
May cause respiratory irritation
Causes damage to hearing through prolonged or repeated exposure if inhaled
Harmful to aquatic life with long lasting effects
Flammable liquid and vapor
Appearance Purple – Clear Physical State Liquid Odor Pungent
_____________________________________________________________________________________________
Page 2 / 10

_____________________________________________________________________________________________
5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018
3. COMPOSITION/INFORMATION ON INGREDIENTS
Chemical Name CAS No. Weight-% Trade Secret
Styrene 100-42-5 39.0
Cobalt compounds Proprietary <0.2 * * The exact percentage (concentration) of composition has been withheld as a trade secret. If CAS number is "proprietary", the specific chemical identity has been withheld as a trade secret. 4. FIRST AID MEASURES First Aid Measures Eye Contact Immediately flush eyes for at least 15 minutes. Get medical attention. Skin Contact Wash off with warm water and soap. Remove contaminated clothing and shoes. If skin irritation persists, call a physician. Wash contaminated clothing before reuse. Inhalation Remove person to fresh air. If signs/symptoms continue, get medical attention. Keep patient warm and at rest. If not breathing, give artificial respiration. If breathing is labored, administer oxygen. Get medical attention immediately. Ingestion Do NOT induce vomiting. Potential for aspiration if swallowed. This material may enter the lungs during vomiting. Immediately give the victim one or two glasses of water or milk to drink. Never give anything by mouth to an unconscious person. GET IMMEDIATE MEDICAL ATTENTION. Most important symptoms and effects, both acute and delayed Most Important Symptoms and Effects No information available. Indication of any immediate medical attention and special treatment needed Notes to Physician Treat symptomatically. 5. FIRE-FIGHTING MEASURES Suitable Extinguishing Media Carbon dioxide (CO2), Foam, Dry chemical, Water spray Unsuitable Extinguishing Media Do not use a solid water stream as it may scatter and spread fire. Specific hazards arising from the chemical Hazardous combustion productsCombustion may produce carbon monoxide, carbon dioxide and irritating or toxic vapors and gases Combustion/explosion hazards Flammable. Vapors may form explosive mixtures with air. Flash back possible over considerable distance. This material may polymerize (react) when its container is exposed to heat (as during a fire). This polymerization increases pressure inside a closed container and may result in the violent rupture of the container. Empty containers may retain product residue (liquid and/or vapor). Do not pressurize, cut, weld, braze, solder, drill, grind, or expose these containers to heat, flame, sparks, static electricity, or other sources of ignition as the container may explode and may cause injury or death. _____________________________________________________________________________________________ Page 3 / 10 Protective Equipment and Precautions for Firefighters Wear self-contained breathing apparatus (SCBA) and full fire-fighting protective clothing. Thoroughly decontaminate all protective _____________________________________________________________________________________________ 5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018 equipment after use. Evacuate all persons from the fire area to a safe location. Move non-burning material, as feasible, to a safe location as soon as possible. Fire fighters should be protected from potential explosion hazard while extinguishing the blaze. DO NOT extinguish a fire resulting from the flow of this flammable liquid until the flow of liquid is effectively shut off. This precaution will help prevent the accumulation of an explosive vapor-air mixture after the initial fire is extinguished. Use water spray to cool fire-exposed containers. 6. ACCIDENTAL RELEASE MEASURES Personal precautions, protective equipment and emergency procedures Personal Precautions Remove all sources of ignition. Evacuate personnel to safe areas. Use personal protective equipment as required. Ensure adequate ventilation. Keep people away from and upwind of spill/leak. Beware of vapors accumulating to form explosive concentrations. Vapors can accumulate in low areas. Environmental precautions Environmental precautions Prevent further leakage or spillage if safe to do so. Do not allow material to contaminate ground water system. Prevent product from entering drains. Soak up with inert absorbent material and dispose of as hazardous waste. Beware of vapors accumulating to form explosive concentrations. Vapors can accumulate in low areas. Methods and material for containment and cleaning up Methods for Containment Prevent spilled material from 1) contaminating soil, 2) entering sanitary sewers, storm sewers, and drainage systems, and 3) entering bodies of water or ditches that lead to waterways. Prevent spreading over a wide area (e.g. by containment or oil barriers). Methods for Clean-up Soak up with inert absorbent material. Remove from surface water (e.g. by skimming or siphoning). Dispose of contaminated material as waste according to item 13. 7. HANDLING AND STORAGE Precautions for safe handling Handling Do not breathe vapor or mist. Avoid contact with skin, eyes or clothing. Wash hands before breaks and immediately after handling the product. Take off contaminated clothing and wash before reuse. Ensure adequate ventilation. Ground and bond containers when transferring material. Use spark-proof tools and explosion-proof equipment. Consult your supplier of promoters and catalysts for additional instructions on proper mixing and usage. Empty containers may retain product residue (liquid and/or vapor). Do not pressurize, cut, weld, braze, solder, drill, grind, or expose these containers to heat, flame, sparks, static electricity, or other sources of ignition as the container may explode and may cause injury or death. Empty drums should be completely drained and properly bunged. Empty drums should be promptly returned to a drum reconditioner or properly disposed. Conditions for safe storage, including any incompatibilities Storage Keep away from heat and sources of ignition. No smoking. Protect from direct sunlight. Keep containers tightly closed in a cool, well-ventilated place. To ensure maximum stability and maintain optimum resin properties, resins should be stored in closed containers at temperatures below 77 F (25 C). 8. EXPOSURE CONTROLS/PERSONAL PROTECTION Exposure limits Components with workplace control parameters. Styrene (CAS #: 100-42-5) ACGIH TLV 20 ppm TWA 40 ppm STEL A4 Not Classifiable as a Human Carcinogen _____________________________________________________________________________________________ Page 4 / 10 _____________________________________________________________________________________________ 5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018 OSHA PEL 100 ppm TWA 200 ppm Ceiling Industry PEL While the federal workplace exposure limit for styrene is 100 ppm, OSHA accepted the styrene industry's proposal to voluntarily meet a PEL of 50 ppm on an 8 hour TWA and a Short Term Exposure Limit (STEL) of 100 ppm, 15 minute exposure. Canada - Alberta OELs 40 ppm STEL 170 mg/m 3 STEL 20 ppm TWA 85 mg/m 3 TWA Canada - Ontario OELs 35 ppm TWA 100 ppm STEL Canada - British Columbia OELs 50 ppm TWA 75 ppm STEL NIOSH IDLH 700 ppm Mexico OEL 100 ppm STEL 425 mg/m 3 STEL 50 ppm TWA 215 mg/m 3 TWA (skin) Legend ACGIH (American Conference of Governmental Industrial Hygienists) TLV (Threshold Limit Value) TWA (time-weighted average) STEL - Short Term Exposure Limit OSHA - Occupational Safety and Health Administration PEL - Permissible Exposure Limit OEL - Occupational Exposure Limit NIOSH - National Institute for Occupational Safety and Health IDLH - Immediately Dangerous to Life or Health SKIN: Skin Absorption Appropriate engineering controls Engineering Controls Use general ventilation to maintain airborne concentrations to levels that are below regulatory and recommended occupational exposure limits. Local ventilation may be required during certain operations. Use explosion-proof electrical equipment. Individual protection measures, such as personal protective equipment Eye/face Protection Safety glasses with side-shields. If splashes are likely to occur:. Tight sealing safety goggles. Ensure that eyewash stations and safety showers are close to the workstation location. Skin Protection Wear protective nitrile rubber or Viton gloves. Gloves made of nitrile rubber or polyvinyl chloride (PVC) may be used for splash protection and brief or intermittent contact with styrenated polyester resin. Please observe the instructions regarding permeability and breakthrough time which are provided by the supplier of the gloves. Also take into consideration the specific local conditions under which the product is used, such as the danger of cuts, abrasion. Impervious clothing. Rubber or plastic boots. Respiratory Protection None required if hazards have been assessed and airborne concentrations are maintained below the exposure limits listed in Section 8. Wear an approved air-purifying respirator with organic vapor cartridges and particulate filters where airborne concentrations may exceed exposure limits in Section 8 and/or there is exposure to dust or mists due to sanding, grinding, cutting, or spraying. Use an approved positive-pressure air-supplied respirator with emergency escape provisions if there is any potential for an uncontrolled release, airborne concentrations are not known, or any other circumstances where air-purifying respirators may not provide adequate protection. General Hygiene Considerations Handle in accordance with good industrial hygiene and safety practice. _____________________________________________________________________________________________ Page 5 / 10 9. PHYSICAL AND CHEMICAL PROPERTIES _____________________________________________________________________________________________ 5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018 Appearance Purple - Clear Odor Pungent Odor threshold 0.2 ppm (Styrene) Physical State Liquid pH No information available Flash point 32 C / 89 F Flash Point Method: Seta closed cup Autoignition Temperature 490 C / 914 F (Styrene) Boiling point / boiling range 146 C / 295 F (Styrene) Melting point / freezing point No information available Flammability Limit in Air Lower 1.1% (Styrene) Upper 6.1% (Styrene) Specific Gravity 1.11 - 1.13 @ 25 C Solubility Insoluble in H2O Evaporation rate 0.49 (BuAc = 1) (Styrene) Vapor Pressure 5 mmHg @ 20 C (Styrene) 6.7 hPa (Styrene) Vapor density 3.6 (Air = 1) (Styrene) Explosive properties No information available Oxidizing Properties No information available Percent Volatile 36 - 42 % by weight VOC Content 437 g/l (calculated) product as supplied Viscosity 375 - 450 cps @ 25 C Partition coefficient No information available Decomposition temperature No information available 10. STABILITY AND REACTIVITY Reactivity Chemical Stability Stable under normal conditions. Stable under recommended storage conditions. Possibility of Hazardous Reactions Hazardous polymerization Polymerization can occur. Hazardous polymerization will occur if contaminated with peroxides, metal salts and polymerization catalysts. Product will undergo hazardous polymerization at temperatures above 150 F (65 C). Conditions to Avoid Heat, flames and sparks. Contamination by those materials referred to under Incompatible materials. Incompatible materials Strong acids. Strong oxidizing agents. Metal salts. Polymerization catalysts. Hazardous decomposition products Hydrocarbons. Carbon monoxide. Carbon dioxide (CO2). Thermal decomposition can lead to release of irritating and toxic gases and vapors. 11. TOXICOLOGICAL INFORMATION Information on likely routes of exposure Primary Routes of Entry Eye contact, Ingestion, Inhalation, Skin Contact, Skin absorption Acute toxicity Styrene Oral LD50 = 1000 mg/kg (Rat) No dangerous reaction known under conditions of normal use. _____________________________________________________________________________________________ Page 6 / 10 _____________________________________________________________________________________________ 5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018 Inhalation LC50 = 11.8 mg/l (4 H) (Rat) Information on toxicological effects Symptoms Symptoms of overexposure may be headache, dizziness, tiredness, nausea and vomiting. Delayed and immediate effects as well as chronic effects from short and long-term exposure Eyes Irritating to eyes. Skin Harmful by skin absorption. Contact causes skin irritation. Prolonged skin contact may defat the skin and produce dermatitis. Inhalation Harmful by inhalation. May cause irritation of respiratory tract. Inhalation of high vapor concentrations can cause central nervous system depression and narcosis. Ingestion Harmful if swallowed. Ingestion may cause gastrointestinal irritation, nausea, vomiting and diarrhea. Aspiration hazard if swallowed - can enter lungs and cause damage. Ingestion is not an anticipated route of exposure for this material in industrial use. Sensitization Not sensitizing. Repeated dose toxicity In humans, styrene may cause a transient decrease in color discrimination and effects on hearing. Repeated or prolonged exposure may cause skin irritation and dermatitis, due to defatting properties of the product. May cause damage to the kidneys, liver, eyes, brain, respiratory system, central nervous system through prolonged or repeated exposure if inhaled. Mutagenic effects Styrene has given mixed positive and negative results in a number of mutagenicity tests. Styrene was not mutagenic without metabolic activation but gave negative and positive mutagenic results with metabolic activation. Carcinogenicity . Styrene ACGIH A4 - Not Classifiable as a Human Carcinogen IARC Group 2A - Probably Carcinogenic to Humans NTP Reasonably anticipated to be human carcinogen Cobalt compounds IARC Group 2B - Possibly Carcinogenic to Humans Legend IARC - International Agency for Research on Cancer NTP - National Toxicology Program Reproductive Toxicity No information available. Neurological effects No information available. STOT - single exposure No information available. STOT - repeated exposure No information available. Target organ effects Liver, Kidney, Central nervous system (CNS), Respiratory system. Aspiration hazard No information available. Unknown acute toxicity 61.1 % of the mixture consists of ingredient(s) of unknown toxicity. The following values are calculated based on chapter 3.1 of the GHS document . ATEmix (oral) 5046 mg/kg ATEmix (dermal) 2019 mg/kg ATEmix (inhalation-vapor) 11.9 mg/L _____________________________________________________________________________________________ Page 7 / 10 _____________________________________________________________________________________________ 5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018 12. ECOLOGICAL INFORMATION Ecotoxicity Styrene Partition coefficient 2.95 Bioconcentration factor (BCF) 13.5 fish Algae EC50 = 1.4 mg/L (Pseudokirchneriella subcapitata) (72h) EC50 0.46 - 4.3 mg/L (Pseudokirchneriella subcapitata) (72h) Fish LC50 3.24 - 4.99 mg/L (Pimephales promelas) (96 h) flow-through LC50 19.03 - 33.53 mg/L (Lepomis macrochirus) (96 h) static LC50 6.75 - 14.5 mg/L (Pimephales promelas) (96 h) static LC50 58.75 - 95.32 mg/L (Poecilia reticulata) (96 h) static Crustacea 3.3 - 7.4: 48 h Daphnia magna mg/L EC50 Cobalt compounds Algae EC50 = 0.639 mg/L Unknown aquatic toxicity 61.2 % of the mixture consists of components(s) of unknown hazards to the aquatic environment. Persistence/Degradability No information available. Bioaccumulation No information available. Other adverse effects No information available. 13. DISPOSAL CONSIDERATIONS Waste treatment methods Disposal Considerations Hazardous waste. Can be incinerated, when in compliance with local regulations. Contaminated packaging Empty containers should be taken for local recycling, recovery or waste disposal. US EPA Waste Number D001 (IGNITABLE): When discarded in its purchased form, this material would be regulated under 40 CFR 261.21 as EPA Hazardous Waste Number D001 based on the characteristic of ignitability. 14. TRANSPORT INFORMATION DOT UN/ID no. UN1866 Proper shipping name RESIN SOLUTION Hazard Class 3 Packing Group III NAERG: 127 TDG UN/ID no. UN1866 Proper shipping name RESIN SOLUTION Hazard Class CLASS 3 Packing Group PGIII NAERG: 127 MEX UN/ID no. UN1866 _____________________________________________________________________________________________ Page 8 / 10 _____________________________________________________________________________________________ 5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018 Proper shipping name RESIN SOLUTION Hazard Class CLASS 3 Packing Group PG III NAERG: 127 IATA UN/ID no. UN1866 Proper shipping name RESIN SOLUTION Hazard Class 3 Packing Group III NAERG: 127 IMDG/IMO UN/ID no. UN1866 Proper shipping name RESIN SOLUTION Hazard Class CLASS 3 Packing Group PG III EmS-No F-E, S-E 15. REGULATORY INFORMATION International Inventories TSCA Inventory Status: All components of this material are listed on the US Toxic Substances Control Act (TSCA) inventory. Canadian Inventory Status: All components of this material are listed on the Canadian Domestic Substances List (DSL) Australian Inventory Status: This product contains only chemicals which are currently listed on the Australian Inventory of Chemical Substances Korean Inventory Status: This product contains only chemicals which are currently listed on the Korean Chemical Substances List Philippine Inventory: This product contains one or more chemicals currently not on the Philippine Inventory of Chemicals and Chemical Substances Japan ENCS: This product contains only chemicals that are currently listed on the Japanese Inventory of Existing and New Chemical Substances Chinese IECS: This product contains only chemicals that are currently listed on the Chinese Inventory of Existing Chemical Substances New Zealand Inventory: This product contains only chemicals which are currently listed on the New Zealand Inventory of Chemicals US Federal Regulations TSCA 12(b) - Export Notification: This material does not contain any components that are subject to the US Toxic Substances Control Act (TSCA) Section 12(b) Export Notification requirements. SARA 313 Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA). This product contains a chemical or chemicals which are subject to the reporting requirements of the Act and and Title 40 of the Code of Federal Regulations, Part 372: Chemical Name CAS No. Weight-% SARA 313 Status Styrene 100-42-5 39.0 Listed Cobalt compounds <0.2 Listed EPCRA: Emergency Planning and Community Right-to-Know Act Should this product meet EPCRA 311/312 Tier reporting criteria at 40 CFR 370, refer to Section 2 of this SDS for appropriate classifications. _____________________________________________________________________________________________ Page 9 / 10 _____________________________________________________________________________________________ 5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018 CWA (Clean Water Act) This product contains the following listed substances: Chemical Name CWA - Reportable Quantities CWA - Toxic Pollutants CWA - Priority Pollutants CWA - Hazardous Substances Styrene 100-42-5 1000 lb Listed Clean Air Act, Section 112 Hazardous Air Pollutants (HAPs) (see 40 CFR 61) This product contains the following HAPs: Chemical Name CAS No. Weight-% HAPS data Styrene 100-42-5 39.0 Cobalt compounds <0.2 Listed CERCLA This product contains the following reportable quantities: Chemical Name 40 CFR 302.4 RQ 40 CFR 355 EHS TPQs Styrene 1000 lb 454 kg Chemical Weapons Convention (CWC) This product contains the following listed substances:. California Proposition 65 WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. Canada This product has been classified in accordance with the hazard criteria of the Controlled Products Regulations (CPR) and the MSDS contains all the information required by the CPR. 16. OTHER INFORMATION Prepared By Polynt Regulatory Department Revision Date 04/Sep/2018 Revision Note None This data sheet contains changes from the previous version in section(s): 15, 16 Former date 28 December 2017 This information is provided in good faith and is correct to the best of Polynt's knowledge as of the date hereof and is designed to assist our customers; however, Polynt makes no representation as to its completeness or accuracy. Our products are intended for sale to industrial and commercial customers. We require customers to inspect and test our products before use and to satisfy themselves as to suitability for their specific applications. Any use which Polynt customers or third parties make of this information, or any reliance on, or decisions made based upon it, are the responsibility of such customer or third party. Polynt disclaims responsibility for damages, or liability, of any kind resulting from the use of this information. THERE ARE NO WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, INCLUDING THOSE OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THIS INFORMATION OR TO THE PRODUCT IT DESCRIBES. IN NO EVENT SHALL POLYNT BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. End of Safety Data Sheet NFPA Rating Health 2 Flammability 3 Instability 1 _____________________________________________________________________________________________ Page 10 / 10

30R32737UV_SDS.pdf

by | Sep 27, 2025

SAFETY DATA SHEET
Revision Date 04/Sep/2018
1. IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKING
Product identifier
Product Description:
POLYLITE 32737-00
Other means of identification
SAP ID(s): 5654 ; 5655
Material Code: 32737-00
Chemical Family Polyester Resin
Recommended use of the chemical and restrictions on use
Recommended Use Surface Casting Resin
Uses advised against No information available
Details of the supplier of the safety data sheet
Emergency Telephone Chemtrec: 1-800-424-9300 (in U.S. & Canada)
+1-703-741-5970 (international)
E-mail address MSDS@polynt.com
2. HAZARDS IDENTIFICATION
Classification
OSHA Regulatory Status
This chemical is considered hazardous by the 2012 OSHA Hazard Communication Standard (29 CFR 1910.1200)
Acute toxicity – Inhalation (Vapors) Category 4
Skin corrosion/irritation Category 2
Serious eye damage/eye irritation Category 2A
Skin sensitization Category 1
Carcinogenicity Sub-category 1B
Reproductive toxicity Category 2
Specific target organ toxicity (single exposure) Category 3
Specific target organ toxicity (repeated exposure) Category 1
Chronic aquatic toxicity Category 3
Label elements
Emergency Overview
Manufacturer/Supplier:
Polynt Composites USA, Inc.
99 East Cottage Avenue
Carpentersville IL 60110
In Canada
Polynt Composites Canada Inc
29 Regan Road
Brampton, Ontario
L7A 1B2
Flammable liquids Category 3
Danger
_____________________________________________________________________________________________
Page 1 / 10
Hazard statements
Harmful if inhaled
Causes skin irritation
Causes serious eye irritation
May cause an allergic skin reaction
May cause cancer

_____________________________________________________________________________________________
5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018
Precautionary Statements – Prevention
Obtain special instructions before use
Do not handle until all safety precautions have been read and understood
Use personal protective equipment as required
Use only outdoors or in a well-ventilated area
Wash face, hands and any exposed skin thoroughly after handling
Contaminated work clothing should not be allowed out of the workplace
Wear protective gloves/protective clothing/eye protection/face protection
Do not breathe mist, vapors, spray
Do not eat, drink or smoke when using this product
Keep away from heat/sparks/open flames/hot surfaces. – No smoking
Keep container tightly closed
Ground/bond container and receiving equipment
Use explosion-proof electrical/ ventilating/ lighting/ equipment
Use only non-sparking tools
Take precautionary measures against static discharge
Keep cool
Avoid release to the environment
Precautionary Statements – Response
IF exposed or concerned: Get medical advice/attention
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing
If eye irritation persists: Get medical advice/attention
If skin irritation or rash occurs: Get medical advice/attention
IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower
IF ON SKIN: Wash with plenty of soap and water
Wash contaminated clothing before reuse
If skin irritation occurs: Get medical advice/attention
IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing
In case of fire: Use CO2, dry chemical, or foam to extinguish
Precautionary Statements – Storage
Store in a well-ventilated place. Keep container tightly closed
Precautionary Statements – Disposal
Dispose of contents/container to industrial incineration plant
Dispose of in accordance with federal, state and local regulations
Hazards not otherwise classified (HNOC)
Not applicable
Other Information
None known
Unknown acute toxicity 61.1 % of the mixture consists of ingredient(s) of unknown toxicity
Unknown aquatic toxicity 61.2 % of the mixture consists of components(s) of unknown hazards to the aquatic
environment
Suspected of damaging fertility or the unborn child
May cause respiratory irritation
Causes damage to hearing through prolonged or repeated exposure if inhaled
Harmful to aquatic life with long lasting effects
Flammable liquid and vapor
Appearance Purple – Clear Physical State Liquid Odor Pungent
_____________________________________________________________________________________________
Page 2 / 10

_____________________________________________________________________________________________
5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018
3. COMPOSITION/INFORMATION ON INGREDIENTS
Chemical Name CAS No. Weight-% Trade Secret
Styrene 100-42-5 39.0
Cobalt compounds Proprietary <0.2 * * The exact percentage (concentration) of composition has been withheld as a trade secret. If CAS number is "proprietary", the specific chemical identity has been withheld as a trade secret. 4. FIRST AID MEASURES First Aid Measures Eye Contact Immediately flush eyes for at least 15 minutes. Get medical attention. Skin Contact Wash off with warm water and soap. Remove contaminated clothing and shoes. If skin irritation persists, call a physician. Wash contaminated clothing before reuse. Inhalation Remove person to fresh air. If signs/symptoms continue, get medical attention. Keep patient warm and at rest. If not breathing, give artificial respiration. If breathing is labored, administer oxygen. Get medical attention immediately. Ingestion Do NOT induce vomiting. Potential for aspiration if swallowed. This material may enter the lungs during vomiting. Immediately give the victim one or two glasses of water or milk to drink. Never give anything by mouth to an unconscious person. GET IMMEDIATE MEDICAL ATTENTION. Most important symptoms and effects, both acute and delayed Most Important Symptoms and Effects No information available. Indication of any immediate medical attention and special treatment needed Notes to Physician Treat symptomatically. 5. FIRE-FIGHTING MEASURES Suitable Extinguishing Media Carbon dioxide (CO2), Foam, Dry chemical, Water spray Unsuitable Extinguishing Media Do not use a solid water stream as it may scatter and spread fire. Specific hazards arising from the chemical Hazardous combustion productsCombustion may produce carbon monoxide, carbon dioxide and irritating or toxic vapors and gases Combustion/explosion hazards Flammable. Vapors may form explosive mixtures with air. Flash back possible over considerable distance. This material may polymerize (react) when its container is exposed to heat (as during a fire). This polymerization increases pressure inside a closed container and may result in the violent rupture of the container. Empty containers may retain product residue (liquid and/or vapor). Do not pressurize, cut, weld, braze, solder, drill, grind, or expose these containers to heat, flame, sparks, static electricity, or other sources of ignition as the container may explode and may cause injury or death. _____________________________________________________________________________________________ Page 3 / 10 Protective Equipment and Precautions for Firefighters Wear self-contained breathing apparatus (SCBA) and full fire-fighting protective clothing. Thoroughly decontaminate all protective _____________________________________________________________________________________________ 5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018 equipment after use. Evacuate all persons from the fire area to a safe location. Move non-burning material, as feasible, to a safe location as soon as possible. Fire fighters should be protected from potential explosion hazard while extinguishing the blaze. DO NOT extinguish a fire resulting from the flow of this flammable liquid until the flow of liquid is effectively shut off. This precaution will help prevent the accumulation of an explosive vapor-air mixture after the initial fire is extinguished. Use water spray to cool fire-exposed containers. 6. ACCIDENTAL RELEASE MEASURES Personal precautions, protective equipment and emergency procedures Personal Precautions Remove all sources of ignition. Evacuate personnel to safe areas. Use personal protective equipment as required. Ensure adequate ventilation. Keep people away from and upwind of spill/leak. Beware of vapors accumulating to form explosive concentrations. Vapors can accumulate in low areas. Environmental precautions Environmental precautions Prevent further leakage or spillage if safe to do so. Do not allow material to contaminate ground water system. Prevent product from entering drains. Soak up with inert absorbent material and dispose of as hazardous waste. Beware of vapors accumulating to form explosive concentrations. Vapors can accumulate in low areas. Methods and material for containment and cleaning up Methods for Containment Prevent spilled material from 1) contaminating soil, 2) entering sanitary sewers, storm sewers, and drainage systems, and 3) entering bodies of water or ditches that lead to waterways. Prevent spreading over a wide area (e.g. by containment or oil barriers). Methods for Clean-up Soak up with inert absorbent material. Remove from surface water (e.g. by skimming or siphoning). Dispose of contaminated material as waste according to item 13. 7. HANDLING AND STORAGE Precautions for safe handling Handling Do not breathe vapor or mist. Avoid contact with skin, eyes or clothing. Wash hands before breaks and immediately after handling the product. Take off contaminated clothing and wash before reuse. Ensure adequate ventilation. Ground and bond containers when transferring material. Use spark-proof tools and explosion-proof equipment. Consult your supplier of promoters and catalysts for additional instructions on proper mixing and usage. Empty containers may retain product residue (liquid and/or vapor). Do not pressurize, cut, weld, braze, solder, drill, grind, or expose these containers to heat, flame, sparks, static electricity, or other sources of ignition as the container may explode and may cause injury or death. Empty drums should be completely drained and properly bunged. Empty drums should be promptly returned to a drum reconditioner or properly disposed. Conditions for safe storage, including any incompatibilities Storage Keep away from heat and sources of ignition. No smoking. Protect from direct sunlight. Keep containers tightly closed in a cool, well-ventilated place. To ensure maximum stability and maintain optimum resin properties, resins should be stored in closed containers at temperatures below 77 F (25 C). 8. EXPOSURE CONTROLS/PERSONAL PROTECTION Exposure limits Components with workplace control parameters. Styrene (CAS #: 100-42-5) ACGIH TLV 20 ppm TWA 40 ppm STEL A4 Not Classifiable as a Human Carcinogen _____________________________________________________________________________________________ Page 4 / 10 _____________________________________________________________________________________________ 5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018 OSHA PEL 100 ppm TWA 200 ppm Ceiling Industry PEL While the federal workplace exposure limit for styrene is 100 ppm, OSHA accepted the styrene industry's proposal to voluntarily meet a PEL of 50 ppm on an 8 hour TWA and a Short Term Exposure Limit (STEL) of 100 ppm, 15 minute exposure. Canada - Alberta OELs 40 ppm STEL 170 mg/m 3 STEL 20 ppm TWA 85 mg/m 3 TWA Canada - Ontario OELs 35 ppm TWA 100 ppm STEL Canada - British Columbia OELs 50 ppm TWA 75 ppm STEL NIOSH IDLH 700 ppm Mexico OEL 100 ppm STEL 425 mg/m 3 STEL 50 ppm TWA 215 mg/m 3 TWA (skin) Legend ACGIH (American Conference of Governmental Industrial Hygienists) TLV (Threshold Limit Value) TWA (time-weighted average) STEL - Short Term Exposure Limit OSHA - Occupational Safety and Health Administration PEL - Permissible Exposure Limit OEL - Occupational Exposure Limit NIOSH - National Institute for Occupational Safety and Health IDLH - Immediately Dangerous to Life or Health SKIN: Skin Absorption Appropriate engineering controls Engineering Controls Use general ventilation to maintain airborne concentrations to levels that are below regulatory and recommended occupational exposure limits. Local ventilation may be required during certain operations. Use explosion-proof electrical equipment. Individual protection measures, such as personal protective equipment Eye/face Protection Safety glasses with side-shields. If splashes are likely to occur:. Tight sealing safety goggles. Ensure that eyewash stations and safety showers are close to the workstation location. Skin Protection Wear protective nitrile rubber or Viton gloves. Gloves made of nitrile rubber or polyvinyl chloride (PVC) may be used for splash protection and brief or intermittent contact with styrenated polyester resin. Please observe the instructions regarding permeability and breakthrough time which are provided by the supplier of the gloves. Also take into consideration the specific local conditions under which the product is used, such as the danger of cuts, abrasion. Impervious clothing. Rubber or plastic boots. Respiratory Protection None required if hazards have been assessed and airborne concentrations are maintained below the exposure limits listed in Section 8. Wear an approved air-purifying respirator with organic vapor cartridges and particulate filters where airborne concentrations may exceed exposure limits in Section 8 and/or there is exposure to dust or mists due to sanding, grinding, cutting, or spraying. Use an approved positive-pressure air-supplied respirator with emergency escape provisions if there is any potential for an uncontrolled release, airborne concentrations are not known, or any other circumstances where air-purifying respirators may not provide adequate protection. General Hygiene Considerations Handle in accordance with good industrial hygiene and safety practice. _____________________________________________________________________________________________ Page 5 / 10 9. PHYSICAL AND CHEMICAL PROPERTIES _____________________________________________________________________________________________ 5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018 Appearance Purple - Clear Odor Pungent Odor threshold 0.2 ppm (Styrene) Physical State Liquid pH No information available Flash point 32 C / 89 F Flash Point Method: Seta closed cup Autoignition Temperature 490 C / 914 F (Styrene) Boiling point / boiling range 146 C / 295 F (Styrene) Melting point / freezing point No information available Flammability Limit in Air Lower 1.1% (Styrene) Upper 6.1% (Styrene) Specific Gravity 1.11 - 1.13 @ 25 C Solubility Insoluble in H2O Evaporation rate 0.49 (BuAc = 1) (Styrene) Vapor Pressure 5 mmHg @ 20 C (Styrene) 6.7 hPa (Styrene) Vapor density 3.6 (Air = 1) (Styrene) Explosive properties No information available Oxidizing Properties No information available Percent Volatile 36 - 42 % by weight VOC Content 437 g/l (calculated) product as supplied Viscosity 375 - 450 cps @ 25 C Partition coefficient No information available Decomposition temperature No information available 10. STABILITY AND REACTIVITY Reactivity Chemical Stability Stable under normal conditions. Stable under recommended storage conditions. Possibility of Hazardous Reactions Hazardous polymerization Polymerization can occur. Hazardous polymerization will occur if contaminated with peroxides, metal salts and polymerization catalysts. Product will undergo hazardous polymerization at temperatures above 150 F (65 C). Conditions to Avoid Heat, flames and sparks. Contamination by those materials referred to under Incompatible materials. Incompatible materials Strong acids. Strong oxidizing agents. Metal salts. Polymerization catalysts. Hazardous decomposition products Hydrocarbons. Carbon monoxide. Carbon dioxide (CO2). Thermal decomposition can lead to release of irritating and toxic gases and vapors. 11. TOXICOLOGICAL INFORMATION Information on likely routes of exposure Primary Routes of Entry Eye contact, Ingestion, Inhalation, Skin Contact, Skin absorption Acute toxicity Styrene Oral LD50 = 1000 mg/kg (Rat) No dangerous reaction known under conditions of normal use. _____________________________________________________________________________________________ Page 6 / 10 _____________________________________________________________________________________________ 5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018 Inhalation LC50 = 11.8 mg/l (4 H) (Rat) Information on toxicological effects Symptoms Symptoms of overexposure may be headache, dizziness, tiredness, nausea and vomiting. Delayed and immediate effects as well as chronic effects from short and long-term exposure Eyes Irritating to eyes. Skin Harmful by skin absorption. Contact causes skin irritation. Prolonged skin contact may defat the skin and produce dermatitis. Inhalation Harmful by inhalation. May cause irritation of respiratory tract. Inhalation of high vapor concentrations can cause central nervous system depression and narcosis. Ingestion Harmful if swallowed. Ingestion may cause gastrointestinal irritation, nausea, vomiting and diarrhea. Aspiration hazard if swallowed - can enter lungs and cause damage. Ingestion is not an anticipated route of exposure for this material in industrial use. Sensitization Not sensitizing. Repeated dose toxicity In humans, styrene may cause a transient decrease in color discrimination and effects on hearing. Repeated or prolonged exposure may cause skin irritation and dermatitis, due to defatting properties of the product. May cause damage to the kidneys, liver, eyes, brain, respiratory system, central nervous system through prolonged or repeated exposure if inhaled. Mutagenic effects Styrene has given mixed positive and negative results in a number of mutagenicity tests. Styrene was not mutagenic without metabolic activation but gave negative and positive mutagenic results with metabolic activation. Carcinogenicity . Styrene ACGIH A4 - Not Classifiable as a Human Carcinogen IARC Group 2A - Probably Carcinogenic to Humans NTP Reasonably anticipated to be human carcinogen Cobalt compounds IARC Group 2B - Possibly Carcinogenic to Humans Legend IARC - International Agency for Research on Cancer NTP - National Toxicology Program Reproductive Toxicity No information available. Neurological effects No information available. STOT - single exposure No information available. STOT - repeated exposure No information available. Target organ effects Liver, Kidney, Central nervous system (CNS), Respiratory system. Aspiration hazard No information available. Unknown acute toxicity 61.1 % of the mixture consists of ingredient(s) of unknown toxicity. The following values are calculated based on chapter 3.1 of the GHS document . ATEmix (oral) 5046 mg/kg ATEmix (dermal) 2019 mg/kg ATEmix (inhalation-vapor) 11.9 mg/L _____________________________________________________________________________________________ Page 7 / 10 _____________________________________________________________________________________________ 5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018 12. ECOLOGICAL INFORMATION Ecotoxicity Styrene Partition coefficient 2.95 Bioconcentration factor (BCF) 13.5 fish Algae EC50 = 1.4 mg/L (Pseudokirchneriella subcapitata) (72h) EC50 0.46 - 4.3 mg/L (Pseudokirchneriella subcapitata) (72h) Fish LC50 3.24 - 4.99 mg/L (Pimephales promelas) (96 h) flow-through LC50 19.03 - 33.53 mg/L (Lepomis macrochirus) (96 h) static LC50 6.75 - 14.5 mg/L (Pimephales promelas) (96 h) static LC50 58.75 - 95.32 mg/L (Poecilia reticulata) (96 h) static Crustacea 3.3 - 7.4: 48 h Daphnia magna mg/L EC50 Cobalt compounds Algae EC50 = 0.639 mg/L Unknown aquatic toxicity 61.2 % of the mixture consists of components(s) of unknown hazards to the aquatic environment. Persistence/Degradability No information available. Bioaccumulation No information available. Other adverse effects No information available. 13. DISPOSAL CONSIDERATIONS Waste treatment methods Disposal Considerations Hazardous waste. Can be incinerated, when in compliance with local regulations. Contaminated packaging Empty containers should be taken for local recycling, recovery or waste disposal. US EPA Waste Number D001 (IGNITABLE): When discarded in its purchased form, this material would be regulated under 40 CFR 261.21 as EPA Hazardous Waste Number D001 based on the characteristic of ignitability. 14. TRANSPORT INFORMATION DOT UN/ID no. UN1866 Proper shipping name RESIN SOLUTION Hazard Class 3 Packing Group III NAERG: 127 TDG UN/ID no. UN1866 Proper shipping name RESIN SOLUTION Hazard Class CLASS 3 Packing Group PGIII NAERG: 127 MEX UN/ID no. UN1866 _____________________________________________________________________________________________ Page 8 / 10 _____________________________________________________________________________________________ 5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018 Proper shipping name RESIN SOLUTION Hazard Class CLASS 3 Packing Group PG III NAERG: 127 IATA UN/ID no. UN1866 Proper shipping name RESIN SOLUTION Hazard Class 3 Packing Group III NAERG: 127 IMDG/IMO UN/ID no. UN1866 Proper shipping name RESIN SOLUTION Hazard Class CLASS 3 Packing Group PG III EmS-No F-E, S-E 15. REGULATORY INFORMATION International Inventories TSCA Inventory Status: All components of this material are listed on the US Toxic Substances Control Act (TSCA) inventory. Canadian Inventory Status: All components of this material are listed on the Canadian Domestic Substances List (DSL) Australian Inventory Status: This product contains only chemicals which are currently listed on the Australian Inventory of Chemical Substances Korean Inventory Status: This product contains only chemicals which are currently listed on the Korean Chemical Substances List Philippine Inventory: This product contains one or more chemicals currently not on the Philippine Inventory of Chemicals and Chemical Substances Japan ENCS: This product contains only chemicals that are currently listed on the Japanese Inventory of Existing and New Chemical Substances Chinese IECS: This product contains only chemicals that are currently listed on the Chinese Inventory of Existing Chemical Substances New Zealand Inventory: This product contains only chemicals which are currently listed on the New Zealand Inventory of Chemicals US Federal Regulations TSCA 12(b) - Export Notification: This material does not contain any components that are subject to the US Toxic Substances Control Act (TSCA) Section 12(b) Export Notification requirements. SARA 313 Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA). This product contains a chemical or chemicals which are subject to the reporting requirements of the Act and and Title 40 of the Code of Federal Regulations, Part 372: Chemical Name CAS No. Weight-% SARA 313 Status Styrene 100-42-5 39.0 Listed Cobalt compounds <0.2 Listed EPCRA: Emergency Planning and Community Right-to-Know Act Should this product meet EPCRA 311/312 Tier reporting criteria at 40 CFR 370, refer to Section 2 of this SDS for appropriate classifications. _____________________________________________________________________________________________ Page 9 / 10 _____________________________________________________________________________________________ 5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018 CWA (Clean Water Act) This product contains the following listed substances: Chemical Name CWA - Reportable Quantities CWA - Toxic Pollutants CWA - Priority Pollutants CWA - Hazardous Substances Styrene 100-42-5 1000 lb Listed Clean Air Act, Section 112 Hazardous Air Pollutants (HAPs) (see 40 CFR 61) This product contains the following HAPs: Chemical Name CAS No. Weight-% HAPS data Styrene 100-42-5 39.0 Cobalt compounds <0.2 Listed CERCLA This product contains the following reportable quantities: Chemical Name 40 CFR 302.4 RQ 40 CFR 355 EHS TPQs Styrene 1000 lb 454 kg Chemical Weapons Convention (CWC) This product contains the following listed substances:. California Proposition 65 WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. Canada This product has been classified in accordance with the hazard criteria of the Controlled Products Regulations (CPR) and the MSDS contains all the information required by the CPR. 16. OTHER INFORMATION Prepared By Polynt Regulatory Department Revision Date 04/Sep/2018 Revision Note None This data sheet contains changes from the previous version in section(s): 15, 16 Former date 28 December 2017 This information is provided in good faith and is correct to the best of Polynt's knowledge as of the date hereof and is designed to assist our customers; however, Polynt makes no representation as to its completeness or accuracy. Our products are intended for sale to industrial and commercial customers. We require customers to inspect and test our products before use and to satisfy themselves as to suitability for their specific applications. Any use which Polynt customers or third parties make of this information, or any reliance on, or decisions made based upon it, are the responsibility of such customer or third party. Polynt disclaims responsibility for damages, or liability, of any kind resulting from the use of this information. THERE ARE NO WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, INCLUDING THOSE OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THIS INFORMATION OR TO THE PRODUCT IT DESCRIBES. IN NO EVENT SHALL POLYNT BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. End of Safety Data Sheet NFPA Rating Health 2 Flammability 3 Instability 1 _____________________________________________________________________________________________ Page 10 / 10

30R32737A_SDS.pdf

by | Sep 27, 2025

SAFETY DATA SHEET
Revision Date 04/Sep/2018
1. IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKING
Product identifier
Product Description:
POLYLITE 32737-00
Other means of identification
SAP ID(s): 5654 ; 5655
Material Code: 32737-00
Chemical Family Polyester Resin
Recommended use of the chemical and restrictions on use
Recommended Use Surface Casting Resin
Uses advised against No information available
Details of the supplier of the safety data sheet
Emergency Telephone Chemtrec: 1-800-424-9300 (in U.S. & Canada)
+1-703-741-5970 (international)
E-mail address MSDS@polynt.com
2. HAZARDS IDENTIFICATION
Classification
OSHA Regulatory Status
This chemical is considered hazardous by the 2012 OSHA Hazard Communication Standard (29 CFR 1910.1200)
Acute toxicity – Inhalation (Vapors) Category 4
Skin corrosion/irritation Category 2
Serious eye damage/eye irritation Category 2A
Skin sensitization Category 1
Carcinogenicity Sub-category 1B
Reproductive toxicity Category 2
Specific target organ toxicity (single exposure) Category 3
Specific target organ toxicity (repeated exposure) Category 1
Chronic aquatic toxicity Category 3
Label elements
Emergency Overview
Manufacturer/Supplier:
Polynt Composites USA, Inc.
99 East Cottage Avenue
Carpentersville IL 60110
In Canada
Polynt Composites Canada Inc
29 Regan Road
Brampton, Ontario
L7A 1B2
Flammable liquids Category 3
Danger
_____________________________________________________________________________________________
Page 1 / 10
Hazard statements
Harmful if inhaled
Causes skin irritation
Causes serious eye irritation
May cause an allergic skin reaction
May cause cancer

_____________________________________________________________________________________________
5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018
Precautionary Statements – Prevention
Obtain special instructions before use
Do not handle until all safety precautions have been read and understood
Use personal protective equipment as required
Use only outdoors or in a well-ventilated area
Wash face, hands and any exposed skin thoroughly after handling
Contaminated work clothing should not be allowed out of the workplace
Wear protective gloves/protective clothing/eye protection/face protection
Do not breathe mist, vapors, spray
Do not eat, drink or smoke when using this product
Keep away from heat/sparks/open flames/hot surfaces. – No smoking
Keep container tightly closed
Ground/bond container and receiving equipment
Use explosion-proof electrical/ ventilating/ lighting/ equipment
Use only non-sparking tools
Take precautionary measures against static discharge
Keep cool
Avoid release to the environment
Precautionary Statements – Response
IF exposed or concerned: Get medical advice/attention
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing
If eye irritation persists: Get medical advice/attention
If skin irritation or rash occurs: Get medical advice/attention
IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower
IF ON SKIN: Wash with plenty of soap and water
Wash contaminated clothing before reuse
If skin irritation occurs: Get medical advice/attention
IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing
In case of fire: Use CO2, dry chemical, or foam to extinguish
Precautionary Statements – Storage
Store in a well-ventilated place. Keep container tightly closed
Precautionary Statements – Disposal
Dispose of contents/container to industrial incineration plant
Dispose of in accordance with federal, state and local regulations
Hazards not otherwise classified (HNOC)
Not applicable
Other Information
None known
Unknown acute toxicity 61.1 % of the mixture consists of ingredient(s) of unknown toxicity
Unknown aquatic toxicity 61.2 % of the mixture consists of components(s) of unknown hazards to the aquatic
environment
Suspected of damaging fertility or the unborn child
May cause respiratory irritation
Causes damage to hearing through prolonged or repeated exposure if inhaled
Harmful to aquatic life with long lasting effects
Flammable liquid and vapor
Appearance Purple – Clear Physical State Liquid Odor Pungent
_____________________________________________________________________________________________
Page 2 / 10

_____________________________________________________________________________________________
5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018
3. COMPOSITION/INFORMATION ON INGREDIENTS
Chemical Name CAS No. Weight-% Trade Secret
Styrene 100-42-5 39.0
Cobalt compounds Proprietary <0.2 * * The exact percentage (concentration) of composition has been withheld as a trade secret. If CAS number is "proprietary", the specific chemical identity has been withheld as a trade secret. 4. FIRST AID MEASURES First Aid Measures Eye Contact Immediately flush eyes for at least 15 minutes. Get medical attention. Skin Contact Wash off with warm water and soap. Remove contaminated clothing and shoes. If skin irritation persists, call a physician. Wash contaminated clothing before reuse. Inhalation Remove person to fresh air. If signs/symptoms continue, get medical attention. Keep patient warm and at rest. If not breathing, give artificial respiration. If breathing is labored, administer oxygen. Get medical attention immediately. Ingestion Do NOT induce vomiting. Potential for aspiration if swallowed. This material may enter the lungs during vomiting. Immediately give the victim one or two glasses of water or milk to drink. Never give anything by mouth to an unconscious person. GET IMMEDIATE MEDICAL ATTENTION. Most important symptoms and effects, both acute and delayed Most Important Symptoms and Effects No information available. Indication of any immediate medical attention and special treatment needed Notes to Physician Treat symptomatically. 5. FIRE-FIGHTING MEASURES Suitable Extinguishing Media Carbon dioxide (CO2), Foam, Dry chemical, Water spray Unsuitable Extinguishing Media Do not use a solid water stream as it may scatter and spread fire. Specific hazards arising from the chemical Hazardous combustion productsCombustion may produce carbon monoxide, carbon dioxide and irritating or toxic vapors and gases Combustion/explosion hazards Flammable. Vapors may form explosive mixtures with air. Flash back possible over considerable distance. This material may polymerize (react) when its container is exposed to heat (as during a fire). This polymerization increases pressure inside a closed container and may result in the violent rupture of the container. Empty containers may retain product residue (liquid and/or vapor). Do not pressurize, cut, weld, braze, solder, drill, grind, or expose these containers to heat, flame, sparks, static electricity, or other sources of ignition as the container may explode and may cause injury or death. _____________________________________________________________________________________________ Page 3 / 10 Protective Equipment and Precautions for Firefighters Wear self-contained breathing apparatus (SCBA) and full fire-fighting protective clothing. Thoroughly decontaminate all protective _____________________________________________________________________________________________ 5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018 equipment after use. Evacuate all persons from the fire area to a safe location. Move non-burning material, as feasible, to a safe location as soon as possible. Fire fighters should be protected from potential explosion hazard while extinguishing the blaze. DO NOT extinguish a fire resulting from the flow of this flammable liquid until the flow of liquid is effectively shut off. This precaution will help prevent the accumulation of an explosive vapor-air mixture after the initial fire is extinguished. Use water spray to cool fire-exposed containers. 6. ACCIDENTAL RELEASE MEASURES Personal precautions, protective equipment and emergency procedures Personal Precautions Remove all sources of ignition. Evacuate personnel to safe areas. Use personal protective equipment as required. Ensure adequate ventilation. Keep people away from and upwind of spill/leak. Beware of vapors accumulating to form explosive concentrations. Vapors can accumulate in low areas. Environmental precautions Environmental precautions Prevent further leakage or spillage if safe to do so. Do not allow material to contaminate ground water system. Prevent product from entering drains. Soak up with inert absorbent material and dispose of as hazardous waste. Beware of vapors accumulating to form explosive concentrations. Vapors can accumulate in low areas. Methods and material for containment and cleaning up Methods for Containment Prevent spilled material from 1) contaminating soil, 2) entering sanitary sewers, storm sewers, and drainage systems, and 3) entering bodies of water or ditches that lead to waterways. Prevent spreading over a wide area (e.g. by containment or oil barriers). Methods for Clean-up Soak up with inert absorbent material. Remove from surface water (e.g. by skimming or siphoning). Dispose of contaminated material as waste according to item 13. 7. HANDLING AND STORAGE Precautions for safe handling Handling Do not breathe vapor or mist. Avoid contact with skin, eyes or clothing. Wash hands before breaks and immediately after handling the product. Take off contaminated clothing and wash before reuse. Ensure adequate ventilation. Ground and bond containers when transferring material. Use spark-proof tools and explosion-proof equipment. Consult your supplier of promoters and catalysts for additional instructions on proper mixing and usage. Empty containers may retain product residue (liquid and/or vapor). Do not pressurize, cut, weld, braze, solder, drill, grind, or expose these containers to heat, flame, sparks, static electricity, or other sources of ignition as the container may explode and may cause injury or death. Empty drums should be completely drained and properly bunged. Empty drums should be promptly returned to a drum reconditioner or properly disposed. Conditions for safe storage, including any incompatibilities Storage Keep away from heat and sources of ignition. No smoking. Protect from direct sunlight. Keep containers tightly closed in a cool, well-ventilated place. To ensure maximum stability and maintain optimum resin properties, resins should be stored in closed containers at temperatures below 77 F (25 C). 8. EXPOSURE CONTROLS/PERSONAL PROTECTION Exposure limits Components with workplace control parameters. Styrene (CAS #: 100-42-5) ACGIH TLV 20 ppm TWA 40 ppm STEL A4 Not Classifiable as a Human Carcinogen _____________________________________________________________________________________________ Page 4 / 10 _____________________________________________________________________________________________ 5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018 OSHA PEL 100 ppm TWA 200 ppm Ceiling Industry PEL While the federal workplace exposure limit for styrene is 100 ppm, OSHA accepted the styrene industry's proposal to voluntarily meet a PEL of 50 ppm on an 8 hour TWA and a Short Term Exposure Limit (STEL) of 100 ppm, 15 minute exposure. Canada - Alberta OELs 40 ppm STEL 170 mg/m 3 STEL 20 ppm TWA 85 mg/m 3 TWA Canada - Ontario OELs 35 ppm TWA 100 ppm STEL Canada - British Columbia OELs 50 ppm TWA 75 ppm STEL NIOSH IDLH 700 ppm Mexico OEL 100 ppm STEL 425 mg/m 3 STEL 50 ppm TWA 215 mg/m 3 TWA (skin) Legend ACGIH (American Conference of Governmental Industrial Hygienists) TLV (Threshold Limit Value) TWA (time-weighted average) STEL - Short Term Exposure Limit OSHA - Occupational Safety and Health Administration PEL - Permissible Exposure Limit OEL - Occupational Exposure Limit NIOSH - National Institute for Occupational Safety and Health IDLH - Immediately Dangerous to Life or Health SKIN: Skin Absorption Appropriate engineering controls Engineering Controls Use general ventilation to maintain airborne concentrations to levels that are below regulatory and recommended occupational exposure limits. Local ventilation may be required during certain operations. Use explosion-proof electrical equipment. Individual protection measures, such as personal protective equipment Eye/face Protection Safety glasses with side-shields. If splashes are likely to occur:. Tight sealing safety goggles. Ensure that eyewash stations and safety showers are close to the workstation location. Skin Protection Wear protective nitrile rubber or Viton gloves. Gloves made of nitrile rubber or polyvinyl chloride (PVC) may be used for splash protection and brief or intermittent contact with styrenated polyester resin. Please observe the instructions regarding permeability and breakthrough time which are provided by the supplier of the gloves. Also take into consideration the specific local conditions under which the product is used, such as the danger of cuts, abrasion. Impervious clothing. Rubber or plastic boots. Respiratory Protection None required if hazards have been assessed and airborne concentrations are maintained below the exposure limits listed in Section 8. Wear an approved air-purifying respirator with organic vapor cartridges and particulate filters where airborne concentrations may exceed exposure limits in Section 8 and/or there is exposure to dust or mists due to sanding, grinding, cutting, or spraying. Use an approved positive-pressure air-supplied respirator with emergency escape provisions if there is any potential for an uncontrolled release, airborne concentrations are not known, or any other circumstances where air-purifying respirators may not provide adequate protection. General Hygiene Considerations Handle in accordance with good industrial hygiene and safety practice. _____________________________________________________________________________________________ Page 5 / 10 9. PHYSICAL AND CHEMICAL PROPERTIES _____________________________________________________________________________________________ 5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018 Appearance Purple - Clear Odor Pungent Odor threshold 0.2 ppm (Styrene) Physical State Liquid pH No information available Flash point 32 C / 89 F Flash Point Method: Seta closed cup Autoignition Temperature 490 C / 914 F (Styrene) Boiling point / boiling range 146 C / 295 F (Styrene) Melting point / freezing point No information available Flammability Limit in Air Lower 1.1% (Styrene) Upper 6.1% (Styrene) Specific Gravity 1.11 - 1.13 @ 25 C Solubility Insoluble in H2O Evaporation rate 0.49 (BuAc = 1) (Styrene) Vapor Pressure 5 mmHg @ 20 C (Styrene) 6.7 hPa (Styrene) Vapor density 3.6 (Air = 1) (Styrene) Explosive properties No information available Oxidizing Properties No information available Percent Volatile 36 - 42 % by weight VOC Content 437 g/l (calculated) product as supplied Viscosity 375 - 450 cps @ 25 C Partition coefficient No information available Decomposition temperature No information available 10. STABILITY AND REACTIVITY Reactivity Chemical Stability Stable under normal conditions. Stable under recommended storage conditions. Possibility of Hazardous Reactions Hazardous polymerization Polymerization can occur. Hazardous polymerization will occur if contaminated with peroxides, metal salts and polymerization catalysts. Product will undergo hazardous polymerization at temperatures above 150 F (65 C). Conditions to Avoid Heat, flames and sparks. Contamination by those materials referred to under Incompatible materials. Incompatible materials Strong acids. Strong oxidizing agents. Metal salts. Polymerization catalysts. Hazardous decomposition products Hydrocarbons. Carbon monoxide. Carbon dioxide (CO2). Thermal decomposition can lead to release of irritating and toxic gases and vapors. 11. TOXICOLOGICAL INFORMATION Information on likely routes of exposure Primary Routes of Entry Eye contact, Ingestion, Inhalation, Skin Contact, Skin absorption Acute toxicity Styrene Oral LD50 = 1000 mg/kg (Rat) No dangerous reaction known under conditions of normal use. _____________________________________________________________________________________________ Page 6 / 10 _____________________________________________________________________________________________ 5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018 Inhalation LC50 = 11.8 mg/l (4 H) (Rat) Information on toxicological effects Symptoms Symptoms of overexposure may be headache, dizziness, tiredness, nausea and vomiting. Delayed and immediate effects as well as chronic effects from short and long-term exposure Eyes Irritating to eyes. Skin Harmful by skin absorption. Contact causes skin irritation. Prolonged skin contact may defat the skin and produce dermatitis. Inhalation Harmful by inhalation. May cause irritation of respiratory tract. Inhalation of high vapor concentrations can cause central nervous system depression and narcosis. Ingestion Harmful if swallowed. Ingestion may cause gastrointestinal irritation, nausea, vomiting and diarrhea. Aspiration hazard if swallowed - can enter lungs and cause damage. Ingestion is not an anticipated route of exposure for this material in industrial use. Sensitization Not sensitizing. Repeated dose toxicity In humans, styrene may cause a transient decrease in color discrimination and effects on hearing. Repeated or prolonged exposure may cause skin irritation and dermatitis, due to defatting properties of the product. May cause damage to the kidneys, liver, eyes, brain, respiratory system, central nervous system through prolonged or repeated exposure if inhaled. Mutagenic effects Styrene has given mixed positive and negative results in a number of mutagenicity tests. Styrene was not mutagenic without metabolic activation but gave negative and positive mutagenic results with metabolic activation. Carcinogenicity . Styrene ACGIH A4 - Not Classifiable as a Human Carcinogen IARC Group 2A - Probably Carcinogenic to Humans NTP Reasonably anticipated to be human carcinogen Cobalt compounds IARC Group 2B - Possibly Carcinogenic to Humans Legend IARC - International Agency for Research on Cancer NTP - National Toxicology Program Reproductive Toxicity No information available. Neurological effects No information available. STOT - single exposure No information available. STOT - repeated exposure No information available. Target organ effects Liver, Kidney, Central nervous system (CNS), Respiratory system. Aspiration hazard No information available. Unknown acute toxicity 61.1 % of the mixture consists of ingredient(s) of unknown toxicity. The following values are calculated based on chapter 3.1 of the GHS document . ATEmix (oral) 5046 mg/kg ATEmix (dermal) 2019 mg/kg ATEmix (inhalation-vapor) 11.9 mg/L _____________________________________________________________________________________________ Page 7 / 10 _____________________________________________________________________________________________ 5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018 12. ECOLOGICAL INFORMATION Ecotoxicity Styrene Partition coefficient 2.95 Bioconcentration factor (BCF) 13.5 fish Algae EC50 = 1.4 mg/L (Pseudokirchneriella subcapitata) (72h) EC50 0.46 - 4.3 mg/L (Pseudokirchneriella subcapitata) (72h) Fish LC50 3.24 - 4.99 mg/L (Pimephales promelas) (96 h) flow-through LC50 19.03 - 33.53 mg/L (Lepomis macrochirus) (96 h) static LC50 6.75 - 14.5 mg/L (Pimephales promelas) (96 h) static LC50 58.75 - 95.32 mg/L (Poecilia reticulata) (96 h) static Crustacea 3.3 - 7.4: 48 h Daphnia magna mg/L EC50 Cobalt compounds Algae EC50 = 0.639 mg/L Unknown aquatic toxicity 61.2 % of the mixture consists of components(s) of unknown hazards to the aquatic environment. Persistence/Degradability No information available. Bioaccumulation No information available. Other adverse effects No information available. 13. DISPOSAL CONSIDERATIONS Waste treatment methods Disposal Considerations Hazardous waste. Can be incinerated, when in compliance with local regulations. Contaminated packaging Empty containers should be taken for local recycling, recovery or waste disposal. US EPA Waste Number D001 (IGNITABLE): When discarded in its purchased form, this material would be regulated under 40 CFR 261.21 as EPA Hazardous Waste Number D001 based on the characteristic of ignitability. 14. TRANSPORT INFORMATION DOT UN/ID no. UN1866 Proper shipping name RESIN SOLUTION Hazard Class 3 Packing Group III NAERG: 127 TDG UN/ID no. UN1866 Proper shipping name RESIN SOLUTION Hazard Class CLASS 3 Packing Group PGIII NAERG: 127 MEX UN/ID no. UN1866 _____________________________________________________________________________________________ Page 8 / 10 _____________________________________________________________________________________________ 5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018 Proper shipping name RESIN SOLUTION Hazard Class CLASS 3 Packing Group PG III NAERG: 127 IATA UN/ID no. UN1866 Proper shipping name RESIN SOLUTION Hazard Class 3 Packing Group III NAERG: 127 IMDG/IMO UN/ID no. UN1866 Proper shipping name RESIN SOLUTION Hazard Class CLASS 3 Packing Group PG III EmS-No F-E, S-E 15. REGULATORY INFORMATION International Inventories TSCA Inventory Status: All components of this material are listed on the US Toxic Substances Control Act (TSCA) inventory. Canadian Inventory Status: All components of this material are listed on the Canadian Domestic Substances List (DSL) Australian Inventory Status: This product contains only chemicals which are currently listed on the Australian Inventory of Chemical Substances Korean Inventory Status: This product contains only chemicals which are currently listed on the Korean Chemical Substances List Philippine Inventory: This product contains one or more chemicals currently not on the Philippine Inventory of Chemicals and Chemical Substances Japan ENCS: This product contains only chemicals that are currently listed on the Japanese Inventory of Existing and New Chemical Substances Chinese IECS: This product contains only chemicals that are currently listed on the Chinese Inventory of Existing Chemical Substances New Zealand Inventory: This product contains only chemicals which are currently listed on the New Zealand Inventory of Chemicals US Federal Regulations TSCA 12(b) - Export Notification: This material does not contain any components that are subject to the US Toxic Substances Control Act (TSCA) Section 12(b) Export Notification requirements. SARA 313 Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA). This product contains a chemical or chemicals which are subject to the reporting requirements of the Act and and Title 40 of the Code of Federal Regulations, Part 372: Chemical Name CAS No. Weight-% SARA 313 Status Styrene 100-42-5 39.0 Listed Cobalt compounds <0.2 Listed EPCRA: Emergency Planning and Community Right-to-Know Act Should this product meet EPCRA 311/312 Tier reporting criteria at 40 CFR 370, refer to Section 2 of this SDS for appropriate classifications. _____________________________________________________________________________________________ Page 9 / 10 _____________________________________________________________________________________________ 5654 ; POLYLITE 32737-00 Revision Date 04/Sep/2018 CWA (Clean Water Act) This product contains the following listed substances: Chemical Name CWA - Reportable Quantities CWA - Toxic Pollutants CWA - Priority Pollutants CWA - Hazardous Substances Styrene 100-42-5 1000 lb Listed Clean Air Act, Section 112 Hazardous Air Pollutants (HAPs) (see 40 CFR 61) This product contains the following HAPs: Chemical Name CAS No. Weight-% HAPS data Styrene 100-42-5 39.0 Cobalt compounds <0.2 Listed CERCLA This product contains the following reportable quantities: Chemical Name 40 CFR 302.4 RQ 40 CFR 355 EHS TPQs Styrene 1000 lb 454 kg Chemical Weapons Convention (CWC) This product contains the following listed substances:. California Proposition 65 WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. Canada This product has been classified in accordance with the hazard criteria of the Controlled Products Regulations (CPR) and the MSDS contains all the information required by the CPR. 16. OTHER INFORMATION Prepared By Polynt Regulatory Department Revision Date 04/Sep/2018 Revision Note None This data sheet contains changes from the previous version in section(s): 15, 16 Former date 28 December 2017 This information is provided in good faith and is correct to the best of Polynt's knowledge as of the date hereof and is designed to assist our customers; however, Polynt makes no representation as to its completeness or accuracy. Our products are intended for sale to industrial and commercial customers. We require customers to inspect and test our products before use and to satisfy themselves as to suitability for their specific applications. Any use which Polynt customers or third parties make of this information, or any reliance on, or decisions made based upon it, are the responsibility of such customer or third party. Polynt disclaims responsibility for damages, or liability, of any kind resulting from the use of this information. THERE ARE NO WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, INCLUDING THOSE OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THIS INFORMATION OR TO THE PRODUCT IT DESCRIBES. IN NO EVENT SHALL POLYNT BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. End of Safety Data Sheet NFPA Rating Health 2 Flammability 3 Instability 1 _____________________________________________________________________________________________ Page 10 / 10

30R010F-5_SDS.pdf

by | Sep 27, 2025

Vinyl Ester Resin
Product name
Product type
Section 1. Identification
Chemical family Aromatic.
Relevant identified uses of the substance or mixture and uses advised against
SDS No. NA-1504:1139 (Version: 4.1)
Uses advised against
Identified uses Used in the manufacture of thermoset plastic parts.
No additional information.
R010-FPA-00
SAFETY DATA SHEET
Date of issue: 03/01/2020
Date of previous issue: 05/15/2019
Emergency telephone number
Supplier’s details
CHEMTREC Within USA and Canada
CHEMTREC Outside USA and Canada
CANUTEC Within Canada
+1 (800) 424-9300
+1 (703) 527-3887
+1 (613) 996-6666
CCN1023
AOC
955 Highway 57 East
Collierville, TN 38017
Phone Number: (901) 854-2800
Hours: 8AM-5pm (Central Time) Mon-Fri
AOC
38 Royal Road
Guelph, Ontario Canada N1H 1G3
Phone Number: (519) 821-5180
Hours: 8am-5pm (Eastern) Mon-Fri
E-Mail: aoc.sds@aocresins.com
Website: www.aocresins.com
United States: Canada:
Section 2. Hazards identification
OSHA/HCS status
FLAMMABLE LIQUIDS Category 3 H226
ACUTE TOXICITY (Inhalation) Category 4 H332
SKIN IRRITATION Category 2 H315
EYE IRRITATION Category 2A H319
CARCINOGENICITY Category 2 H351
REPRODUCTIVE TOXICITY Category 2 H361d
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) Category 3 H335
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) Category 1 H372
ASPIRATION HAZARD Category 1 H304
Classification of the substance or mixture
Signal word
Danger
Hazard statements
H226: Flammable liquid and vapor.
H332: Harmful if inhaled.
H319: Causes serious eye irritation.
H315: Causes skin irritation.
H361d: Suspected of damaging the unborn child.
H351: Suspected of causing cancer.
H304: May be fatal if swallowed and enters airways.
H335: May cause respiratory irritation.
H372: Causes damage to organs through prolonged or repeated exposure if inhaled. (hearing organs, kidneys)
Hazard pictograms
Precautionary statements
GHS label elements
General
This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).
Page: 1 of 9Date of issue: 03/01/2020
Date of previous issue: 05/15/2019NA-1504:1139 (Version: 4.1)
R010-FPA-00

Section 2. Hazards identification
Prevention
P201: Obtain special instructions before use.
P202: Do not handle until all safety precautions have been read and understood.
P280: Wear protective gloves/protective clothing/eye protection/face protection.
P210: Keep away from heat, sparks, open flames and hot surfaces. – No smoking.
P240: Ground/bond container and receiving equipment.
P241: Use explosion-proof electrical/ventilating/lighting/material-handling equipment.
P242: Use only non-sparking tools.
P243: Take precautionary measures against static discharge.
P233: Keep container tightly closed.
P271: Use only outdoors or in a well-ventilated area.
P260: Do not breathe vapor or mist.
P270: Do not eat, drink or smoke when using this product.
P264: Wash hands thoroughly after handling.
Response
P314: Get medical attention if you feel unwell.
P308+P313: IF exposed or concerned: Get medical attention.
P304+P340: IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
P312: Call a POISON CENTER or physician if you feel unwell.
P370+P378: In case of fire: Use dry chemical, CO , water spray (fog) or foam.
P301+P310: IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.
P331: Do NOT induce vomiting.
P308+P313: IF exposed or concerned: Get medical advice/attention.
P303+P361+P353: IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower.
P362+P364: Take off contaminated clothing and wash it before reuse.
P332+P313: If skin irritation occurs: Get medical attention.
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue
rinsing.
P337+P313: If eye irritation persists: Get medical attention.
P391: Collect spillage.
Storage
P405: Store locked up.
P403+P235: Store in a well-ventilated place. Keep cool.
P233: Keep container tightly closed.
Disposal
P501: Dispose of contents and container in accordance with all local, regional, national and international regulations.
P101: If medical advice is needed, have product container or label at hand.
P102: Keep out of reach of children.
Hazards not otherwise classified
None known.
Section 3. Composition/information on ingredients
Ingredient name CAS number %
There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are
classified as hazardous to health or the environment and hence require reporting in this section.
Substance/mixture
Occupational exposure limits, if available, are listed in Section 8.
Mixture.
styrene 100-42-5 35.3
Section 4. First aid measures
Immediately flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Use of buffered baby
shampoo will aid in removal. If irritation persists, get medical attention.
In case of contact, immediately flush skin with plenty of water. Remove contaminated clothing and shoes. If irritation persists, seek
medical attention. Wash contaminated clothing before reuse. Clean shoes thoroughly before reuse.
Move the victim to a safe area as soon as possible. Allow the victim to rest in a well-ventilated area. If breathing is difficult, give oxygen.
If the victim is not breathing, perform mouth-to-mouth resuscitation. Seek immediate medical attention.
Eye contact
Skin contact
Inhalation
Ingestion
Description of necessary first aid measures
Page: 2 of 9Date of issue: 03/01/2020
Date of previous issue: 05/15/2019NA-1504:1139 (Version: 4.1)
R010-FPA-00

Section 4. First aid measures
Wash out mouth with water. Remove dentures if any. Stop if the exposed person feels sick as vomiting may be dangerous. Do not
induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit does not
enter the lungs. Seek immediate medical attention.
Notes to physician
Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled.
Most important symptoms/effects, acute and delayed
See toxicological information (Section 11)
Indication of immediate medical attention and special treatment needed, if necessary
Irritating to mouth, throat and stomach.
Causes serious eye irritation.
Causes skin irritation.
Harmful if inhaled. May cause respiratory irritation. May cause drowsiness or dizziness.
Eye contact
Skin contact
Inhalation
Ingestion
Over-exposure signs/symptoms
Eye contact
Inhalation
Skin contact
Ingestion
Adverse symptoms may include the following: pain or irritation, watering, redness.
Adverse symptoms may include the following: respiratory tract irritation, coughing.
Adverse symptoms may include the following: irritation, redness.
Adverse symptoms may include the following: Irritating to mouth, throat and stomach.
Section 5. Fire-fighting measures
Fire water contaminated with this material must be contained and prevented from being discharged to any waterway, sewer or drain.
Hazardous thermal decomposition products
Specific hazards arising from the chemical
Decomposition products may include the following materials: carbon dioxide, carbon monoxide nitrogen oxides
Flammable liquid and vapor. In a fire or if heated, a pressure increase will occur and the container may burst, with the risk of a
subsequent explosion. The vapor/gas is heavier than air and will spread along the ground. Vapors may accumulate in low or confined
areas or travel a considerable distance to a source of ignition and flash back. Runoff to sewer may create fire or explosion hazard. This
material is harmful to aquatic life with long lasting effects. Fire water contaminated with this material must be contained and prevented
from being discharged to any waterway, sewer or drain.
Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated
in positive pressure mode.
Special protective equipment for fire-fighters
Use dry chemical, CO , water spray (fog) or foam.
Extinguishing media
Do not use water jet.
Suitable extinguishing media
Unsuitable extinguishing media
Special protective actions for fire-fighters
Section 6. Accidental release measures
Environmental precautions
Personal precautions, protective equipment and emergency procedures
For non-emergency personnel
For emergency responders
No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Do not touch or walk
through spilled material. Shut off all ignition sources. No flares, smoking or flames in hazard area. Avoid breathing vapor or mist.
Provide adequate ventilation.
If specialised clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials.
Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment. See also the information in
“For non-emergency personnel”.
Page: 3 of 9Date of issue: 03/01/2020
Date of previous issue: 05/15/2019NA-1504:1139 (Version: 4.1)
R010-FPA-00

Section 6. Accidental release measures
Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water courses,
basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and collect spillage with non-
combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local
regulations (see Section 13). Use spark-proof tools and explosion-proof equipment. Dispose of via a licensed waste disposal contractor.
Contaminated absorbent material may pose the same hazard as the spilled product. Note: see Section 1 for emergency contact
information and Section 13 for waste disposal.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the
product has caused environmental pollution (sewers, waterways, soil or air). Water polluting material. May be harmful to the environment
if released in large quantities.
Stop leak if without risk. Move containers from spill area. Dilute with water and mop up if water-soluble. Alternatively, or if water-insoluble,
absorb with an inert dry material and place in an appropriate waste disposal container. Use spark-proof tools and explosion-proof
equipment. Dispose of via a licensed waste disposal contractor.
Methods and materials for containment and cleaning up
Small spill
Large spill
Section 7. Handling and storage
Advice on general occupational hygiene
Conditions for safe storage, including any incompatibilities
Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash
hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating
areas. See also Section 8 for additional information on hygiene measures.
Store in accordance with local regulations. Store in a segregated and approved area. Store in original container protected from direct
sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Eliminate all
ignition sources. Segregate from oxidizing materials. Keep container tightly closed and sealed until ready for use. Containers that have
been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate
containment to avoid environmental contamination. Refer to the product label and/or technical data sheet for further information.
Protective measures
Put on appropriate personal protective equipment (see Section 8). Eating, drinking and smoking should be prohibited in areas where this
material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove
contaminated clothing and protective equipment before entering eating areas. Do not breathe vapor or mist. Do not ingest. Avoid contact
with eyes, skin and clothing. Avoid release to the environment. Use only with adequate ventilation. Wear appropriate respirator when
ventilation is inadequate. Do not enter storage areas and confined spaces unless adequately ventilated. Keep in the original container or
an approved alternative made from a compatible material, kept tightly closed when not in use. Store and use away from heat, sparks,
open flame or any other ignition source. Use only non-sparking tools. Take precautionary measures against electrostatic discharges.
Empty containers retain product residue and can be hazardous. Do not reuse container.
Precautions for safe handling
styrene ACGIH TLV (United States, 3/2019). Absorbed through skin.
TWA: 20 ppm 8 hours.
STEL: 40 ppm 15 minutes.
OSHA PEL Z2 (United States, 2/2013).
TWA: 100 ppm 8 hours.
CEIL: 200 ppm
AMP: 600 ppm 5 minutes.
NIOSH REL (United States, 10/2016).
TWA: 50 ppm 10 hours.
TWA: 215 mg/m 10 hours.
STEL: 100 ppm 15 minutes.
STEL: 425 mg/m 15 minutes.
Section 8. Exposure controls/personal protection
Ingredient name Exposure limits
Appropriate engineering controls
Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or other engineering controls to keep worker
exposure to airborne contaminants below any recommended or statutory limits. The engineering controls also need to keep gas, vapor or
dust concentrations below any lower explosive limits. Use explosion-proof ventilation equipment.
Hygiene measures
Control parameters
Individual protection measures
Occupational exposure limits
Page: 4 of 9Date of issue: 03/01/2020
Date of previous issue: 05/15/2019NA-1504:1139 (Version: 4.1)
R010-FPA-00

Section 8. Exposure controls/personal protection
Hand protection
Use a properly fitted, air-purifying or air-fed respirator complying with an approved standard if a risk assessment indicates this is
necessary. Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the safe working
limits of the selected respirator.
Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products
if a risk assessment indicates this is necessary.
Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid
exposure to liquid splashes, mists or dusts.
Eye/face protection
Respiratory protection
Body protection
Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be
approved by a specialist before handling this product.
Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end
of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Ensure that eyewash stations
and safety showers are close to the workstation location.
Other skin protection
Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks
involved and should be approved by a specialist before handling this product.
Section 9. Physical and chemical properties
Physical state
Melting point
Vapor pressure
Relative density
Vapor density
Solubility
Liquid.
23.8 F / 30.6 C (Styrene)
1.1 (Water = 1)
3.6 (Air = 1) (Styrene )
<2.58 mm Hg@ 70 F / 21.1 C per ASTM D 323 Slight. Aromatic.Odor pH Yellow.Color Evaporation rate < 1 (Butyl acetate = 1) Auto-ignition temperature Flash point 914 F / 490 C (Styrene) 88 F / 31 C (Styrene) Not available. Not applicable. Viscosity Not available. 0.01 - 0.1 ppm (Styrene)Odor threshold Partition coefficient: n-octanol/water Appearance Boiling point 293 F / 145 C (Styrene) Flammability (solid, gas) Not applicable. Lower and upper explosive (flammable) limits Lower: 1.1% Upper: 6.1% (Styrene) Molecular weight 1,000 to 15,000 Decomposition temperature Not available. Section 10. Stability and reactivity Hazardous decomposition products Conditions to avoid Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld, braze, solder, drill, grind or expose containers to heat or sources of ignition. Under normal conditions of storage and use, hazardous decomposition products should not be produced. The product is stable. Stable under recommended storage and handling conditions (see Section 7). Chemical stability Reactive or incompatible with the following materials: oxidizing materials Incompatible materials Possibility of hazardous reactions Under normal conditions of storage and use, hazardous reactions will not occur. Reactivity No specific test data related to reactivity available for this product or its ingredients. Page: 5 of 9Date of issue: 03/01/2020 Date of previous issue: 05/15/2019NA-1504:1139 (Version: 4.1) R010-FPA-00 Section 11. Toxicological information Acute toxicity styrene LC50 Inhalation Gas. Rat 2770 ppm 4 hours LC50 Inhalation Vapor Rat 11800 mg/m 4 hours LC50 Inhalation Vapor Rat 5634.2 ppm 4 hours LD50 Oral Rat 2650 mg/kg - Ingredient name Result Species Dose Exposure Carcinogenicity Mutagenicity Teratogenicity Reproductive toxicity Irritation/Corrosion styrene Eyes - Mild irritant Human - 50 ppm - Eyes - Moderate irritant Rabbit - 24 hours 100 mg- Eyes - Severe irritant Rabbit - 100 mg - Skin - Mild irritant Rabbit - 500 mg - Skin - Moderate irritant Rabbit - 100 % - Ingredient name Result Score Exposure Observation Sensitization Species Inhalation Harmful if inhaled. May cause respiratory irritation. May cause drowsiness or dizziness. Irritating to mouth, throat and stomach. Ingestion Skin contact Causes skin irritation. Causes serious eye irritation. Eye contact Symptoms related to the physical, chemical and toxicological characteristics Skin contact Adverse symptoms may include the following: respiratory tract irritation, coughing. Adverse symptoms may include the following: irritation, redness. Eye contact Adverse symptoms may include the following: pain or irritation, watering, redness. Specific target organ toxicity (single exposure) Specific target organ toxicity (repeated exposure) Aspiration hazard Information on toxicological effects Potential acute health effects Classification styrene - 2A Reasonably anticipated to be a human carcinogen. Ingredient name NTPIARCACGIH May cause sensitization by skin contact. No known significant effects or critical hazards. 1) Negative Study A published study concluded that the mechanism for producing cancer in mice exposed to styrene is not applicable in human metabolism. (June 2013 Pharmacology & Toxicology 66 (2013)) 2) Negative Study A recent update to an extensive study of reinforced plastic workers from 1948-1977 concluded that there was no coherent evidence that styrene exposure increased risk of cancer (March 2013 Epidemiology Vol. 24 Issue 2) 3) Positive Study Styrene induced pulmonary toxicity and carcinogenicity in mice was shown to be caused by a metabolite of styrene, probably styrene oxide. (Dec.2001 Toxicology Vol.169 Issue 2) Suspected of damaging the unborn child. No known significant effects or critical hazards. May cause respiratory irritation. A study of long term effects of workers exposed to styrene levels in the range of 25-35 ppm, 8 hour TWA, indicated a possible mild hearing loss. May be fatal if swallowed and enters airways. Inhalation Page: 6 of 9Date of issue: 03/01/2020 Date of previous issue: 05/15/2019NA-1504:1139 (Version: 4.1) R010-FPA-00 Section 11. Toxicological information Ingestion Adverse symptoms may include the following: Irritating to mouth, throat and stomach. Section 12. Ecological information LogPow BCF Potential Bioaccumulative potential Other adverse effects No known effect according to our database. styrene 0.35 13.49 low Toxicity styrene Acute EC50 1400 g/l Fresh water Algae - Pseudokirchneriella subcapitata 72 hours Acute EC50 720 g/l Fresh water Algae - Pseudokirchneriella subcapitata 96 hours Acute EC50 4700 g/l Fresh water Daphnia - Daphnia magna 48 hours Acute LC50 52 mg/l Marine water Crustaceans - Artemia salina 48 hours Acute LC50 4020 g/l Fresh water Fish - Pimephales promelas 96 hours Chronic NOEC 63 g/l Fresh water Algae - Pseudokirchneriella subcapitata 96 hours Ingredient name SpeciesResult Exposure Persistence and degradability Soil/water partition coefficient (KOC) Not available. Mobility in soil Not available. Ingredient name Section 13. Disposal considerations The generation of waste should be avoided or minimized wherever possible. Empty containers or liners may retain some product residues. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Disposal of this product, solutions and any by- products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Avoid disposal. Attempt to use product completely in accordance with intended use. Waste packaging should be recycled. Incineration or landfill should only be considered when recycling is not feasible. Disposal methods The information in this section contains generic advice and guidance. The list of Identified Uses in Section 1 should be consulted for any available use-specific information provided in the Exposure Scenario(s). Special precautions This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers that have not been cleaned or rinsed out. Empty containers or liners may retain some product residues. Do not cut, weld or grind used containers unless they have been cleaned thoroughly internally. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Section 14. Transport information Resin Solution 3 III UN1866UN number Proper shipping name Transport hazard class(es) Packing group DOT /TDG / IMDG/IMO / ICAO/IATA and National regulations. Additional information US regulations require the reporting of spills when the amount exceeds the Reportable Quantity (RQ) for specific components of this material. See CERCLA in Section 15, Regulatory Information, for the Reportable Quantities. Environmental hazards Marine pollutant: No. IMDGEmergency schedules (EmS): F-E, S-E Remarks: FP- 31 C IATANo additional information. Page: 7 of 9Date of issue: 03/01/2020 Date of previous issue: 05/15/2019NA-1504:1139 (Version: 4.1) R010-FPA-00 Section 14. Transport information Special precautions for user Transport within user s premises: always transport in closed containers that are upright and secure. Ensure that persons transporting the product know what to do in the event of an accident or spillage. Section 15. Regulatory information International regulations lists All components are listed or exempted. SARA 313 Ingredient name styrene 100-42-5 Form R - Reporting requirements SARA 311/312 United States inventory (TSCA 8b) Australia (AICS) All components are listed or exempted. Canada (DSL) All components are listed or exempted. China (IECSC) All components are listed or exempted. Europe (EINECS) All components are listed or exempted. Japan Japan inventory (ENCS): Not determined. Japan inventory (ISHL): Not determined. Republic of Korea (KECI) All components are listed or exempted. Malaysia (EHS Register) Not determined. New Zealand (NZIoC) All components are listed or exempted. Philippines (PICCS) Not determined. Taiwan (CSNN) All components are listed or exempted. CAS number California Prop. 65 State regulations styrene - 1000 lbs. (453.6 kg)CERCLA RQ - WARNING: This product can expose you to Styrene, which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov. Per the June 13, 2016 Federal Register notice, EPA harmonized the EPCRA 311/312 hazard categories with the 2012 OSHA hazard communication standard for classifying and labeling of chemicals (i.e. GHS). Please refer to Section 2 of the SDS to identify the appropriate hazard categories for reporting purposes. U.S. Federal regulations Section 16. Other information History Version Prepared by Date of previous issue 03/01/2020 05/15/2019 4.1 National Fire Protection Association (U.S.A.) Reprinted with permission from NFPA 704-2001, Identification of the Hazards of Materials for Emergency Response Copyright 1997, National Fire Protection Association, Quincy, MA 02269. This reprinted material is not the complete and official position of the National Fire Protection Association, on the referenced subject which is represented only by the standard in its entirety. Copyright 2001, National Fire Protection Association, Quincy, MA 02269. This warning system is intended to be interpreted and applied only by properly trained individuals to identify fire, health and reactivity hazards of chemicals. The user is referred to certain limited number of chemicals with recommended classifications in NFPA 49 and NFPA 325, which would be used as a guideline only. Whether the chemicals are classified by NFPA or not, anyone using the 704 systems to classify chemicals does so at their own risk. AOC Corporate Regulatory Affairs 2 3 2 Health Special Instability Flammability Date of issue Page: 8 of 9Date of issue: 03/01/2020 Date of previous issue: 05/15/2019NA-1504:1139 (Version: 4.1) R010-FPA-00 Section 16. Other information AOC is a registered trademark of the AOC group of companies. The information contained in this data sheet is based on laboratory data and field experience. We believe this information to be reliable, but do not guarantee its applicability to the user s process or assume any liability for occurrences arising out of its use. The user, by accepting the products as described herein, agrees to be responsible for thoroughly testing each such product before committing it to production. Altek , Atryl , Atryl TCA , Chroma-Tek , EcoTek , FirePel , Hydropel , Moldtru , PulTru , Vibrin , Vicast , Vipel , the AOC name, the AOC logo, and the Trusted Solutions logo are registered trademarks of the AOC group of companies. Our recommendations should not be construed as inducements to infringe any patent or violate any law, safety code or insurance regulation. The information and recommendations contained herein are to the best of our knowledge accurate and reliable, but no rights whatsoever may be derived by any party other than those expressly agreed to with a selling entity of the AOC group of companies in a legally binding agreement. AOC hereby makes no warranty of any kind, express or implied, including those of merchantability and fitness for purpose. Unless explicitly agreed to in writing by AOC otherwise, all offers, quotations, sales and deliveries of AOC products are subject to the general conditions of sale of AOC. Notice to reader Indicates information that has changed from previously issued version. Key to abbreviations ATE = Acute Toxicity Estimate BCF = Bioconcentration Factor GHS = Globally Harmonized System of Classification and Labelling of Chemicals IATA = International Air Transport Association IBC = Intermediate Bulk Container IMDG = International Maritime Dangerous Goods LogPow = logarithm of the octanol/water partition coefficient MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution) UN = United Nations This Safety Data Sheet (SDS) and its content are the confidential and proprietary information of AOC and it may not be modified, altered, deconstructed, or presented in any other manner, without the explicit authorization of AOC and/or its legal counsel. Page: 9 of 9Date of issue: 03/01/2020 Date of previous issue: 05/15/2019NA-1504:1139 (Version: 4.1) R010-FPA-00

30R010F-00_SDS.pdf

by | Sep 27, 2025

30P-431-F_SDS.pdf

by | Sep 27, 2025

Ultra Premium White Finish Coat
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
Issue date: 12/5/2024

12/5/2024 (Issue date) EN (English) 1/13

SECTION 1: Identification
1.1. Identification
Product form : Mixture
Trade name : Ultra Premium White Finish Coat
CAS-No. : mixture
Product code : 30P-431
Formula : N/A
Other means of identification : Unsaturated Polyester Resin Product
Corrosion-Resistant Resin
1.2. Recommended use and restrictions on use
Use of the substance/mixture : Laminating
1.3. Supplier
Dura Technologies, Inc.
2720 South Willow Avenue #A
Bloomington, CA 92316

909-546-1162
ChemTrec US: 800.424.9300
ChemTrec Int: +1 70 3527 3887
1.4. Emergency telephone number
Emergency number : ChemTrec US: 800.424.9300 Int: +1 70 3527 3887
CHEMTREC: 1-800-424-9300
SECTION 2: Hazard(s) identification
2.1. Classification of the substance or mixture
GHS-US classification
Flammable liquids, Category 3 H226 Flammable liquid and vapour.
Acute toxicity (inhal.), Category 4 H332 Harmful if inhaled.
Skin corrosion/irritation, Category 2 H315 Causes skin irritation.
Serious eye damage/eye irritation, Category 2 H319 Causes serious eye irritation.
Reproductive toxicity, Category 2 H361 Suspected of damaging fertility or the unborn child.
Specific target organ toxicity Single exposure, Category 3,
Respiratory tract irritation
H335 May cause respiratory irritation.
Specific target organ toxicity Repeated exposure, Category 1 H372 Causes damage to organs through prolonged or repeated
exposure.
Full text of H-statements: see section 16
2.2. GHS Label elements, including precautionary statements
GHS US labelling
Hazard pictograms (GHS US) :

Signal word (GHS US) : Danger

Ultra Premium White Finish Coat
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

12/5/2024 (Issue date) EN (English) 2/13

Hazard statements (GHS US) : H226 – Flammable liquid and vapour.
H315 – Causes skin irritation.
H319 – Causes serious eye irritation.
H332 – Harmful if inhaled.
H335 – May cause respiratory irritation.
H361 – Suspected of damaging fertility or the unborn child.
H372 – Causes damage to organs through prolonged or repeated exposure.
Precautionary statements (GHS US) : P201 – Obtain special instructions before use.
P202 – Do not handle until all safety precautions have been read and understood.
P210 – Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No
smoking.
P233 – Keep container tightly closed.
P240 – Ground/Bond container and receiving equipment.
P241 – Use explosion-proof electrical, lighting, ventilating equipment.
P242 – Use only non-sparking tools.
P243 – Take precautionary measures against static discharge.
P260 – Do not breathe dust/fume/gas/mist/vapours/spray.
P261 – Avoid breathing dust/fume/gas/mist/vapours/spray.
P264 – Wash EXPOSED AREA. thoroughly after handling.
P270 – Do not eat, drink or smoke when using this product.
P271 – Use only outdoors or in a well-ventilated area.
P280 – Wear eye protection, protective clothing, protective gloves.
P302+P352 – If on skin: Wash with plenty of water.
P303+P361+P353 – If on skin (or hair): Take off immediately all contaminated clothing. Rinse
skin with water/shower.
P304+P340 – If inhaled: Remove person to fresh air and keep comfortable for breathing.
P305+P351+P338 – IF IN EYES: Rinse cautiously with water for several minutes. Remove
contact lenses, if present and easy to do. Continue rinsing.
P308+P313 – If exposed or concerned: Get medical advice/attention.
P312 – Call a poison center or doctor if you feel unwell.
P314 – Get medical advice/attention if you feel unwell.
P321 – Specific treatment (see supplemental first aid instruction on this label).
P332+P313 – If skin irritation occurs: Get medical advice/attention.
P337+P313 – If eye irritation persists: Get medical advice/attention.
P362+P364 – Take off contaminated clothing and wash it before reuse.
P370+P378 – In case of fire: Use carbon dioxide (CO2), dry chemical powder, foam to
extinguish.
P403+P233 – Store in a well-ventilated place. Keep container tightly closed.
P403+P235 – Store in a well-ventilated place. Keep cool.
P405 – Store locked up.
P501 – Dispose of contents/container to LOCAL, STATE, AND NATIONAL REGULATIONS..
2.3. Other hazards which do not result in classification
No additional information available
2.4. Unknown acute toxicity (GHS US)
No additional information available
SECTION 3: Composition/information on ingredients
3.1. Substances
Not applicable

Ultra Premium White Finish Coat
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

12/5/2024 (Issue date) EN (English) 3/13

3.2. Mixtures
Name Product identifier % GHS-US classification
styrene, inhibited CAS-No.: 100-42-5 38.5 Flam. Liq. 3, H226
Acute Tox. 4 (Inhalation:vapour),
H332
Skin Irrit. 2, H315
Eye Irrit. 2, H319
Repr. 2, H361
STOT RE 1, H372
Aquatic Chronic 3, H412
Full text of hazard classes and H-statements : see section 16
SECTION 4: First-aid measures
4.1. Description of first aid measures
First-aid measures general : Never give anything by mouth to an unconscious person. If you feel unwell, seek medical advice
(show the label where possible). IF exposed or concerned: Get medical advice/attention. Call a
poison center or a doctor if you feel unwell.
First-aid measures after inhalation : Remove person to fresh air and keep comfortable for breathing. Allow affected person to breathe
fresh air. Allow the victim to rest. Remove person to fresh air and keep comfortable for breathing.
Call a POISON CENTER/doctor if you feel unwell. Call a poison center or a doctor if you feel
unwell.
First-aid measures after skin contact : Rinse skin with water/shower. Take off immediately all contaminated clothing. Wash with plenty
of water/ . Wash contaminated clothing before reuse. If skin irritation occurs: wash throughly for
five minutes. seek medical attention. Get medical advice/attention. Specific treatment (see seek
medical attention. on this label). If skin irritation or rash occurs: Get medical advice/attention.
First-aid measures after eye contact : Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to
do. Continue rinsing. If eye irritation persists: SEEK IMMEDIATE MEDICAL ATTENTION. Get
medical advice/attention.
First-aid measures after ingestion : Rinse mouth. Do NOT induce vomiting. Obtain emergency medical attention. Call a poison
center or a doctor if you feel unwell.
4.2. Most important symptoms and effects (acute and delayed)
Potential adverse human health effects and
symptoms
: Harmful if inhaled. Based on available data, the classification criteria are not met.
Symptoms/effects : May cause genetic defects (avoid skin contact and inhalation.). May cause cancer (avoid skin
contact and inhalation.).
Symptoms/effects after inhalation : Danger of serious damage to health by prolonged exposure through inhalation. Harmful if
inhaled. May cause respiratory irritation.
Symptoms/effects after skin contact : Causes skin irritation. Irritation. May cause an allergic skin reaction.
Symptoms/effects after eye contact : Causes serious eye irritation.
4.3. Immediate medical attention and special treatment, if necessary
Treat symptomatically.
SECTION 5: Fire-fighting measures
5.1. Suitable (and unsuitable) extinguishing media
Suitable extinguishing media : Sand. Water spray. Dry powder. Foam. Carbon dioxide.
Unsuitable extinguishing media : Do not use a heavy water stream.

Ultra Premium White Finish Coat
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

12/5/2024 (Issue date) EN (English) 4/13

5.2. Specific hazards arising from the chemical
Fire hazard : Highly flammable liquid and vapour. Flammable liquid and vapour.
Explosion hazard : May form flammable/explosive vapour-air mixture.
Reactivity in case of fire : No reactivity hazard other than the effects described in sub-sections below.
Hazardous decomposition products in case of fire : Toxic fumes may be released.
5.3. Special protective equipment and precautions for fire-fighters
Firefighting instructions : Use water spray or fog for cooling exposed containers. Exercise caution when fighting any
chemical fire. Prevent fire fighting water from entering the environment.
Protection during firefighting : Do not enter fire area without proper protective equipment, including respiratory protection. Do
not attempt to take action without suitable protective equipment. Self-contained breathing
apparatus. Complete protective clothing.
SECTION 6: Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
General measures : Remove ignition sources. Use special care to avoid static electric charges. No open flames. No
smoking.
6.1.1. For non-emergency personnel
Protective equipment : Gloves. Protective goggles. Protective clothing.
Emergency procedures : Ventilate spillage area. Evacuate unnecessary personnel. No open flames, no sparks, and no
smoking. Do not breathe dust/fume/gas/mist/vapours/spray. Avoid contact with skin and eyes.
6.1.2. For emergency responders
Protective equipment : Do not attempt to take action without suitable protective equipment. Equip cleanup crew with
proper protection. For further information refer to section 8: “Exposure controls/personal
protection”.
Emergency procedures : Ventilate area.
6.2. Environmental precautions
Avoid release to the environment. Prevent entry to sewers and public waters. Notify authorities if liquid enters sewers or public waters.
6.3. Methods and material for containment and cleaning up
For containment : Dam up the liquid spill. Contain released product, pump into suitable containers.
Methods for cleaning up : Take up liquid spill into absorbent material. Soak up spills with inert solids, such as clay or
diatomaceous earth as soon as possible. Collect spillage. Store away from other materials.
Notify authorities if product enters sewers or public waters.
Other information : Dispose of materials or solid residues at an authorized site.
6.4. Reference to other sections
See Heading 8. Exposure controls and personal protection. For further information refer to section 13.
SECTION 7: Handling and storage
7.1. Precautions for safe handling
Additional hazards when processed : Handle empty containers with care because residual vapours are flammable.

Ultra Premium White Finish Coat
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

12/5/2024 (Issue date) EN (English) 5/13

Precautions for safe handling : Wear personal protective equipment. Wash hands and other exposed areas with mild soap and
water before eating, drinking or smoking and when leaving work. Provide good ventilation in
process area to prevent formation of vapour. No open flames. No smoking. Use only non-
sparking tools. Use only outdoors or in a well-ventilated area. Obtain special instructions before
use. Do not handle until all safety precautions have been read and understood. Eliminate all
ignition sources if safe to do so. Take precautionary measures against static discharge. Keep
away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
Ground/bond container and receiving equipment. Flammable vapours may accumulate in the
container. Use explosion-proof equipment. Do not breathe dust/fume/gas/mist/vapours/spray.
Avoid contact with skin and eyes.
Hygiene measures : Wash HANDS thoroughly after handling. Wash contaminated clothing before reuse.
Contaminated work clothing should not be allowed out of the workplace. Do not eat, drink or
smoke when using this product. Always wash hands after handling the product.
7.2. Conditions for safe storage, including any incompatibilities
Technical measures : Proper grounding procedures to avoid static electricity should be followed. Ground/bond
container and receiving equipment. Use explosion-proof electrical, ventilating and lighting
equipment. equipment.
Storage conditions : Keep only in the original container in a cool, well ventilated place away from : HEAT SPARKS
OR OPEN FLAMES. Keep in fireproof place. Keep container tightly closed. Store locked up.
Store in a well-ventilated place. Keep cool.
Incompatible products : Strong bases. Strong acids.
Incompatible materials : Sources of ignition. Direct sunlight. Heat sources.
SECTION 8: Exposure controls/personal protection
8.1. Control parameters

Ultra Premium White Finish Coat (mixture)
No additional information available

styrene, inhibited (100-42-5)
USA – ACGIH – Occupational Exposure Limits
ACGIH OEL TWA [ppm] 20 ppm
ACGIH OEL STEL [ppm] 40 ppm
8.2. Appropriate engineering controls
Appropriate engineering controls : Ensure exposure is below occupational exposure limits (where available). Ensure good
ventilation of the work station.
Environmental exposure controls : Avoid release to the environment.
8.3. Individual protection measures/Personal protective equipment
Personal protective equipment:
Avoid all unnecessary exposure.

Hand protection:
Wear protective gloves.

Eye protection:
Chemical goggles or safety glasses. Safety glasses

Ultra Premium White Finish Coat
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

12/5/2024 (Issue date) EN (English) 6/13

Skin and body protection:
Wear suitable protective clothing

Respiratory protection:
Wear appropriate mask. [In case of inadequate ventilation] wear respiratory protection.

Personal protective equipment symbol(s):

Other information:
Do not eat, drink or smoke during use.
SECTION 9: Physical and chemical properties
9.1. Information on basic physical and chemical properties
Physical state : Liquid
Colour : White
Odour : characteristic
Odour threshold : No data available
pH : No data available
Melting point : Not applicable
Freezing point : No data available
Boiling point : 293 F
Flash point : 86 F
Relative evaporation rate (butylacetate=1) : No data available
Flammability (solid, gas) : Highly flammable liquid and vapour. Flammable liquid and vapour.
Vapour pressure : No data available
Relative vapour density at 20 C : No data available
Relative density : 1.20
Density : 1.2 kg/l
Solubility : No data available
Partition coefficient n-octanol/water (Log Pow) : No data available
Auto-ignition temperature : No data available
Decomposition temperature : No data available
Viscosity, kinematic : No data available
Viscosity, dynamic : No data available
Explosive limits : No data available
Explosive properties : No data available
Oxidising properties : No data available
9.2. Other information
VOC content : 465 g/l VOC is based on 100% Evaporation of monomers.
SECTION 10: Stability and reactivity
10.1. Reactivity
No reactivity hazard other than the effects described in sub-sections below. Flammable liquid and vapour.

Ultra Premium White Finish Coat
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

12/5/2024 (Issue date) EN (English) 7/13

10.2. Chemical stability
Polymerization can result in formation of solid deposits, even in vapour space. Not established. Highly flammable liquid and vapour. May form
flammable/explosive vapour-air mixture. Flammable liquid and vapour.
10.3. Possibility of hazardous reactions
Not established.
10.4. Conditions to avoid
Direct sunlight. Extremely high or low temperatures. Open flame. Overheating. Heat. Sparks. Avoid contact with hot surfaces. No flames, no sparks.
Eliminate all sources of ignition.
10.5. Incompatible materials
Strong acids. Strong bases.
10.6. Hazardous decomposition products
fume. Carbon monoxide. Carbon dioxide. May release flammable gases.
SECTION 11: Toxicological information
11.1. Information on toxicological effects
Acute toxicity (oral) : Not classified
Acute toxicity (dermal) : Not classified
Acute toxicity (inhalation) : Harmful if inhaled.

Ultra Premium White Finish Coat (mixture)
ATE US (gases) 4500 ppmv/4h
ATE US (vapours) 11 mg/l/4h
ATE US (dust,mist) 1.5 mg/l/4h

styrene, inhibited (100-42-5)
LD50 oral rat 5000 mg/kg (Rat; Literature study; >6000 mg/kg bodyweight; Rat; Weight of evidence)
LD50 oral > 6000 mg/kg bodyweight (Hamster, Male, Weight of evidence, Oral)
LD50 dermal rat > 2000 mg/kg bodyweight (OECD 402: Acute Dermal Toxicity, 24 h, Rat, Male / female,
Experimental value, Dermal)
LD50 dermal rabbit 5010 mg/kg (Rabbit; Literature study)
LC50 Inhalation – Rat 11.8 mg/l air (4 h, Rat, Inconclusive, insufficient data, Inhalation (vapours))
LC50 Inhalation – Rat [ppm] 2770 ppm/4h (Rat; Literature study)
ATE US (vapours) 11 mg/l/4h

Skin corrosion/irritation : Causes skin irritation.

styrene, inhibited (100-42-5)
pH Not applicable

Serious eye damage/irritation : Causes serious eye irritation.

styrene, inhibited (100-42-5)
pH Not applicable

Respiratory or skin sensitisation : Not classified

Germ cell mutagenicity : Not classified

Ultra Premium White Finish Coat
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

12/5/2024 (Issue date) EN (English) 8/13

Carcinogenicity : Not classified

styrene, inhibited (100-42-5)
IARC group 2B – Possibly carcinogenic to humans
National Toxicology Program (NTP) Status Reasonably anticipated to be Human Carcinogen

Reproductive toxicity : Suspected of damaging fertility or the unborn child.

STOT-single exposure : May cause respiratory irritation.

STOT-repeated exposure : Causes damage to organs through prolonged or repeated exposure.

styrene, inhibited (100-42-5)
STOT-repeated exposure Causes damage to organs through prolonged or repeated exposure.

Aspiration hazard : Not classified
Viscosity, kinematic : No data available

styrene, inhibited (100-42-5)
Viscosity, kinematic 0.8 mm /s

Potential adverse human health effects and
symptoms
: Harmful if inhaled. Based on available data, the classification criteria are not met.
Symptoms/effects : May cause genetic defects (avoid skin contact and inhalation.). May cause cancer (avoid skin
contact and inhalation.).
Symptoms/effects after inhalation : Danger of serious damage to health by prolonged exposure through inhalation. Harmful if
inhaled. May cause respiratory irritation.
Symptoms/effects after skin contact : Causes skin irritation. Irritation. May cause an allergic skin reaction.
Symptoms/effects after eye contact : Causes serious eye irritation.
SECTION 12: Ecological information
12.1. Toxicity
Ecology – general : Dangerous for the environment. Harmful to aquatic life.

styrene, inhibited (100-42-5)
LC50 – Fish [1] 10 mg/l (OECD 203: Fish, Acute Toxicity Test, 96 h, Pimephales promelas, Flow-through
system, Fresh water, Experimental value, GLP)
EC50 – Crustacea [1] 4.7 mg/l (OECD 202: Daphnia sp. Acute Immobilisation Test, 48 h, Daphnia magna, Flow-
through system, Fresh water, Experimental value, GLP)
ErC50 algae 4.9 mg/l (EPA OTS 797.1050, 72 h, Pseudokirchneriella subcapitata, Static system, Fresh
water, Experimental value, GLP)
12.2. Persistence and degradability
Ultra Premium White Finish Coat (mixture)
Persistence and degradability Not established.

styrene, inhibited (100-42-5)
Persistence and degradability Biodegradable in the soil. Readily biodegradable in water.
Chemical oxygen demand (COD) 2.8 g O /g substance
ThOD 3.07 g O /g substance
BOD (% of ThOD) 0.42 (Literature study)

Ultra Premium White Finish Coat
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations

12/5/2024 (Issue date) EN (English) 9/13

12.3. Bioaccumulative potential
Ultra Premium White Finish Coat (mixture)
Bioaccumulative potential Not established.

styrene, inhibited (100-42-5)
BCF – Fish [1] 35.5 (Carassius auratus, Literature study)
Partition coefficient n-octanol/water (Log Pow) 2.96 (Experimental value, OECD 107: Partition Coefficient (n-octanol/water): Shake Flask
Method, 25 C)
Bioaccumulative potential Low potential for bioaccumulation (Log Kow < 4). 12.4. Mobility in soil styrene, inhibited (100-42-5) Surface tension 0.032 N/m (20 C) Organic Carbon Normalized Adsorption Coefficient (Log Koc) 2.55 (log Koc, Estimated value) Ecology - soil Low potential for adsorption in soil. 12.5. Other adverse effects Other information : Avoid release to the environment. SECTION 13: Disposal considerations 13.1. Disposal methods Regional legislation (waste) : Disposal must be done according to official regulations. Waste treatment methods : Dispose of contents/container in accordance with licensed collector s sorting instructions. Sewage disposal recommendations : Do not discharge into drains. Product/Packaging disposal recommendations : Dispose in a safe manner in accordance with local/national regulations. Dispose of contents/container to approved disposal site.. Additional information : Handle empty containers with care because residual vapours are flammable. Flammable vapours may accumulate in the container. Ecology - waste materials : Avoid release to the environment. SECTION 14: Transport information In accordance with DOT / TDG / IMDG / IATA 14.1. UN number DOT NA No : UN1866 UN-No. (TDG) : UN1866 UN-No. (IMDG) : 1866 UN-No. (IATA) : 1866 14.2. UN proper shipping name Proper Shipping Name (DOT) : Resin solution Proper Shipping Name (TDG) : RESIN SOLUTION Proper Shipping Name (IMDG) : RESIN SOLUTION Proper Shipping Name (IATA) : Resin solution Ultra Premium White Finish Coat Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 12/5/2024 (Issue date) EN (English) 10/13 14.3. Transport hazard class(es) DOT Transport hazard class(es) (DOT) : 3 Hazard labels (DOT) : 3 TDG Transport hazard class(es) (TDG) : 3 Hazard labels (TDG) : 3 IMDG Transport hazard class(es) (IMDG) : 3 Danger labels (IMDG) : 3 IATA Transport hazard class(es) (IATA) : 3 Danger labels (IATA) : 3 14.4. Packing group Packing group (DOT) : III Packing group (TDG) : III Packing group (IMDG) : III Packing group (IATA) : III 14.5. Environmental hazards Other information : No supplementary information available. 14.6. Special precautions for user DOT UN-No.(DOT) : UN1866 Ultra Premium White Finish Coat Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 12/5/2024 (Issue date) EN (English) 11/13 DOT Special Provisions (49 CFR 172.102) : B1 - If the material has a flash point at or above 38 C (100 F) and below 93 C (200 F), then the bulk packaging requirements of 173.241 of this subchapter are applicable. If the material has a flash point of less than 38 C (100 F), then the bulk packaging requirements of 173.242 of this subchapter are applicable. B52 - Notwithstanding the provisions of 173.24b of this subchapter, non-reclosing pressure relief devices are authorized on DOT 57 portable tanks. IB3 - Authorized IBCs: Metal (31A, 31B and 31N); Rigid plastics (31H1 and 31H2); Composite (31HZ1 and 31HA2, 31HB2, 31HN2, 31HD2 and 31HH2). Additional Requirement: Only liquids with a vapor pressure less than or equal to 110 kPa at 50 C (1.1 bar at 122 F), or 130 kPa at 55 C (1.3 bar at 131 F) are authorized, except for UN2672 (also see Special Provision IP8 in Table 2 for UN2672). T2 - 1.5 178.274(d)(2) Normal............. 178.275(d)(3) TP1 - The maximum degree of filling must not exceed the degree of filling determined by the following: Degree of filling = 97 / (1 + a (tr - tf)) Where: tr is the maximum mean bulk temperature during transport, and tf is the temperature in degrees celsius of the liquid during filling. DOT Packaging Exceptions (49 CFR 173.xxx) : 150 DOT Packaging Non Bulk (49 CFR 173.xxx) : 173 DOT Packaging Bulk (49 CFR 173.xxx) : 242 DOT Quantity Limitations Passenger aircraft/rail (49 CFR 173.27) : 60 L DOT Quantity Limitations Cargo aircraft only (49 CFR 175.75) : 220 L DOT Vessel Stowage Location : A - The material may be stowed on deck or under deck on a cargo vessel and on a passenger vessel. TDG UN-No. (TDG) : UN1866 Explosive Limit and Limited Quantity Index : 5 L Excepted quantities (TDG) : E1 Passenger Carrying Road Vehicle or Passenger Carrying Railway Vehicle Index : 60 L Emergency Response Guide (ERG) Number : 127 IMDG Special provisions (IMDG) : 223, 955 Packing instructions (IMDG) : P001, LP01 Special packing provisions (IMDG) : PP1 IBC packing instructions (IMDG) : IBC03 Tank instructions (IMDG) : T2 Tank special provisions (IMDG) : TP1 EmS-No. (Fire) : F-E - FIRE SCHEDULE Echo - NON-WATER-REACTIVE FLAMMABLE LIQUIDS EmS-No. (Spillage) : S-E - SPILLAGE SCHEDULE Echo - FLAMMABLE LIQUIDS, FLOATING ON WATER Stowage category (IMDG) : A Properties and observations (IMDG) : Miscibility with water depends upon the composition. IATA PCA Excepted quantities (IATA) : E1 PCA Limited quantities (IATA) : Y344 PCA limited quantity max net quantity (IATA) : 10L PCA packing instructions (IATA) : 355 PCA max net quantity (IATA) : 60L CAO packing instructions (IATA) : 366 CAO max net quantity (IATA) : 220L Special provisions (IATA) : A3 ERG code (IATA) : 3L 14.7. Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code Not applicable Ultra Premium White Finish Coat Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 12/5/2024 (Issue date) EN (English) 12/13 SECTION 15: Regulatory information 15.1. US Federal regulations Commercial status of components according to the United States Environmental Protection Agency s Toxic Substances Control Act (TSCA): Name CAS-No. Listing Commercial status Flags styrene, inhibited 100-42-5 Present Active styrene, inhibited (100-42-5) Subject to reporting requirements of United States SARA Section 313 Listed on EPA Hazardous Air Pollutant (HAPS) CERCLA RQ 1000 lb SARA Section 311/312 Hazard Classes Immediate (acute) health hazard Reactive hazard - No Fire hazard Delayed (chronic) health hazard 15.2. International regulations CANADA styrene, inhibited (100-42-5) Listed on the Canadian DSL (Domestic Substances List) EU-Regulations No additional information available National regulations styrene, inhibited (100-42-5) Listed on IARC (International Agency for Research on Cancer) Listed as carcinogen on NTP (National Toxicology Program) 15.3. US State regulations styrene, inhibited (100-42-5) U.S. - California - Proposition 65 - Carcinogens List U.S. - California - Proposition 65 - Developmental Toxicity U.S. - California - Proposition 65 - Reproductive Toxicity - Female U.S. - California - Proposition 65 - Reproductive Toxicity - Male No significant risk level (NSRL) Maximum allowable dose level (MADL) Yes No No No 27 g/day Component State or local regulations styrene, inhibited(100-42-5) U.S. - Massachusetts - Right To Know List; U.S. - New Jersey - Right to Know Hazardous Substance List; U.S. - Pennsylvania - RTK (Right to Know) List SECTION 16: Other information according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations Other information : None. Ultra Premium White Finish Coat Safety Data Sheet according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations 12/5/2024 (Issue date) EN (English) 13/13 Full text of H-statements H226 Flammable liquid and vapour. H315 Causes skin irritation. H319 Causes serious eye irritation. H332 Harmful if inhaled. H335 May cause respiratory irritation. H361 Suspected of damaging fertility or the unborn child. H372 Causes damage to organs through prolonged or repeated exposure. H412 Harmful to aquatic life with long lasting effects. NFPA health hazard : 2 - Materials that, under emergency conditions, can cause temporary incapacitation or residual injury. NFPA fire hazard : 3 - Liquids and solids (including finely divided suspended solids) that can be ignited under almost all ambient temperature conditions. NFPA reactivity : 2 - Materials that readily undergo violent chemical change at elevated temperatures and pressures. Hazard Rating Health : 2 Moderate Hazard - Temporary or minor injury may occur Flammability : 3 Serious Hazard - Materials capable of ignition under almost all normal temperature conditions. Includes flammable liquids with flash points below 73 F and boiling points above 100 F. as well as liquids with flash points between 73 F and 100 F. (Classes IB IC) Physical : 1 Slight Hazard - Materials that are normally stable but can become unstable (self-react) at high temperatures and pressures. Materials may react non-violently with water or undergo hazardous polymerization in the absence of inhibitors. Personal protection : H - Splash goggles, Gloves, Synthetic apron, Vapor respirator Safety Data Sheet (SDS), USA To the best of our knowledge this SDS is accurate. The the extent allowed by law, this statement is made in lieu of an other warranties, expressed or implied including but not limited to any implied warranty of merchantability or fitness for a particular purpose and is in lieu of any other obligations or liability on the part of Dura Technoligies, Inc.