by | Sep 27, 2025
Direction for Use
Recommended Procedure
This material is ready-to-use and requires no
dilution. Best application is achieved by applying a
thin coating using a wiping brushing or spraying. The
ideal application evenly wets the surface and dries to
a glossy layer of mold release. Over-application can
result in drips, runs or puddles of release can cause
part defects. If over applied, remove the excess with
an absorbent cloth prior to molding. Some customers
find a brush useful to even out the Stoner
M802
Mold Release on complicated molds. Best results
are obtained when release is applied shortly before
molding. Treated molds heated for more than 30
minutes at 250 F may require touch-up prior to molding.
Call for special instructions if parts will be painted,
glued or over-molded.
Storage and Handling
See SDS for complete instruction prior to use. Do not
use near ignition sources. Do not expose container
to heat or store at temperatures above 120 F. This
product is contains flammable solvents and proper
ventilation and static controls should be used. Proper
eye and skin protection should be used and some
operators prefer to wear an apron when applying
release or handling parts.
Packaging
Stoner
M802 Urethane Mold Release is available in:
5-gallon pails & 55-gallon drum
Part # M802 (Solvent Based)
Technical Assistance
Call: 800-227-5538 or 1 (717) 786-7355
Email: CustomerService@StonerMolding.com
Visit: StonerMolding.com
NO RISK GUARANTEE . Stoner Molding guarantees 100% satisfaction or your
money back. If you re ever dissatisfied with any Stoner Molding product, simply
return the unused portion for a full refund.
Product Description
Stoner
M802 Urethane Mold Release is specially
formulated as a release agent and anti-stick lubricant
for molded urethanes and similar materials. Provides
fast, easy part removal from molds and multiple part
releases per application. Improves molding efficiency
in many processes including injection, pour cast,
and extrusion molding. Economical a light coating
produces best results.
M802 Urethane Mold Release ADVANTAGES:
Saves time lets you remove urethane parts
from molds quickly and easily.
Fast evaporating for rapid molding at ambient
temperatures and above.
Improves part appearance and reduces defects
caused by sticking.
Contains no Class I or Class II Ozone Depleting
Substances
Contains no chlorinated solvents such as
1,1,1 trichloroethane or methylene chloride.
Colorless and non-staining.
Uses
Stoner
M802 Urethane Mold Release is a release
agent and anti-stick lubricant for molded urethanes and
similar materials.
PRODUCT INFORMATION
Stoner
M802
Urethane Mold Release
Rev 19.7
Made
inUSA
StonerMolding.com
1070 Robert Fulton Hwy. Quarryville, PA 17566 1-800-227-5538 1-717-786-7355
by | Sep 27, 2025
RELEASES COMPOUNDS POLISHES SEALERS
TR INDUSTRIES
11022 Vulcan Street
South Gate, CA 90280-0893
Phone 562 -923-0838 Fax 562-861-3475
www.trmoldrelease.com info@trmoldrelease.com
TR-309
REGULAR COMPOUND
MEDIUM CUTTING PASTE
DESCRIPTION:
TR-309 is a medium coarse off-white paste compound developed specifically for light oxidation and sanding scratch
removal on polyester gel-coats.
PRODUCT FEATURES:
Fast cutting action for quick effective removal light sanding marks
Good initial gloss achieved on finished parts when sanding for minor defect repair
Remains moist while buffing with less spotting and drying
Restores gloss to lightly oxidized & weathered finishes
Contains no silicones or waxes
Economically priced
PHYSICAL PROPERTIES:
Specific Gravity: 1.23 (10.25lbs./Gal)
Viscosity: soft paste water/petroleum emulsion blend
Color: off-white
USES:
To provide good initial uniform gloss while removing sanding scratches (600g-800g), light oxidation and minor
surface imperfections on all gel coated finishes.
APPLICATION:
Apply TR-309 to gel-coated surface and spread evenly. Using a high speed electric variable speed buffer equipped
with all wool twisted buffing pad set buffer speed to 2,400 RPM for best results. Work in a 2 x 2 overlapping
surface area using medium pressure to keep surface moist to avoid drying out and burnishing. As polish begins to
dry gradually reduce buffing pressure to achieve a smooth uniform gloss appearance. Use a buffing spur to clean
pad frequently during use to remove excess compound build up.
NOTE:
For optimum results polish with TR-308 Fine Finish II to achieve a high gloss mirror like swirl free finish after using
TR-309 regular compound.
PACKAGING:
TR-309 is available in Gallon 4×1 case, 5gal pail or 55gal drum. Recommended to store in a cool dry place to
maintain one year shelf life stability.
FOR INDUSTRIAL USE ONLY
The information contained herein is based on tests considered to be reliable and accurate. Because of the wide variance of associated materials
and conditions, however no warranty is expressed or implied. Each user is encouraged to prepare a test part for their particular application.
by | Sep 27, 2025
SAFETY DATA SHEET (SDS) VERSION 2.3.33 1/26/2018
4340 E Miraloma Ave (P) 714-854-9531
Anaheim, CA 92807 (F) 714-854-1689 1
SECTION 1 IDENTIFICATION AND COMPANY D ETAILS
Product Name: WP-1 FinishRite White
Product Code(s): COMA-01
Manufacturer:
Maverick Abrasives
4340 E Miraloma Ave
Anaheim, CA 92807
Telephone Number: 714-854-9531
Fax Number: 714-854-1689
SECTION 2 HAZARDOUS INGREDIENTS/IDENTITY INFORMATION
Aluminum Oxide CAS #1344-28-1 Non-Hazardous
Barium Sulfate CAS #7727-43-7 Non-Hazardous
Paraffin And Hydrocarbon CAS #8002-74-2 Non-Hazardous SECTION 3 HAZARD INFORMATION
Inhalation: Material not considered inhalation hazard. Buffing & polishing may produce dust which over long-term
exposure may result in lung-disease.
Ingestion: Should not be ingested.
Skin Contact: No danger upon skin contact. Can be rubbed off with a cloth and soap and water.
Eye Contact: May be mildly irritable to eye.
SECTION 4 FIRST AID MEASURES
Skin Contact: In case of incidental skin contact remove excess after industrial use with damp rag. Wash hands with
soap and water.
Eye Contact: Remove with warm water applied gently to eye, flushing for 15 minutes or until debris is completely
removed.
Ingestion: Contact your local medical professional for consultation upon ingestion.
Inhalation: N/A
SAFETY DATA SHEET (SDS) VERSION 2.3.33 1/26/2018
4340 E Miraloma Ave (P) 714-854-9531
Anaheim, CA 92807 (F) 714-854-1689 2
SECTION 5 FIRE-FIGHTING MEASURES
Suitable Extinguishing Media
Special Firefighting Procedures: No special firefighting procedures necessary.
Unusual Fire and Explosions Hazard: No unusual fire hazards present.
SECTION 6 ACCIDENTAL RELEASE MEASURES
No special release measures required. Use dry disposal collection.
Chemical Safety Goggles Splash Suit Gloves Rubber Boots
SECTION 7 PRECAUTIONS FOR SAFE HANDLING AND USE
Steps to be taken in the event of spillage or chemical release: Wear suitable protective clothing.
Waste Disposal Method: Dispose of in accordance with national and local regulations of inert non-hazardous waste
material.
Precautions to be taken in Handling and Storage: Store in a cool, dry place (2- 30 C) in original sealed containers
away from heat sources and sunlight. Avoid contact with strong oxidants and strong acids.
Other Precautions: N/A
SECTION 8 EXPOSURE CONTROLS AND PERSONAL PROTECTION
Occupational Exposure Limits: N/A
Respiratory System: Wear appropriate respirator when ventilation is inadequa te
Skin and Body: N/A
Hands: N/A
Eyes: N/A
Other/Special: N/A
SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES
Physical State: Paste/Liquid
Color: White
Odor: Click here to enter text.
SAFETY DATA SHEET (SDS) VERSION 2.3.33 1/26/2018
4340 E Miraloma Ave (P) 714-854-9531
Anaheim, CA 92807 (F) 714-854-1689 3
Melting Point: Click here to enter text.
Flash Point: Click here to enter text.
SECTION 10 REACTIVITY DATA
Stability: N/A
Conditions to Avoid: N/A
Incompatibility: N/A
Hazardous Decomposition or By-products: N/A
Hazardous Polymerization: N/A
SECTION 11 TOXICOLOGICAL INFORMATION
The toxicological information for the components is: Non -toxic.
SECTION 12 ECOLOGICAL INFORMATION
Data is not yet available
SECTION 13 DISPOSAL CONSIDERATIONS
This material is not regarded as hazardous waste. Observe all federal, state, and local environmental regulations.
SECTION 14 TRANSPORT INFORMATION
Non-hazardous for road, sea, and airfreight.
SECTION 15 REGULATORY INFORMATION
Irritant
Safety Phrases: S16 Keep away from sources of ignition No Smoking
S24/25 Avoid contact with skin & eyes.
S26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
S36/37/39 Wear suitable protective clothing, gloves, and eye protection.
Risk Phrases: R10 Flammable
SAFETY DATA SHEET (SDS) VERSION 2.3.33 1/26/2018
4340 E Miraloma Ave (P) 714-854-9531
Anaheim, CA 92807 (F) 714-854-1689 4
Regulations: The Chemicals (Hazard Information and Packaging f or Supply) regulations 2002
1999/45/EC Dangerous Preparations Directive.
91/155/EC Safety Data Sheets Directive.
SECTION 16 OTHER INFORMATION
Notice to Reader:
To the best of our knowledge the information contained herein is accurate.
However, neither the named supplier nor any of its subsidiaries assumes any liability whatsoever for the accuracy
or completeness of the information contained herein.
Final determination of the suitability of any material is the sole responsibility of the user. All materials may present
unknown hazards and should be used with caution. Although certain hazards are described herein we cannot
guarantee that these are the only hazards that exist.
by | Sep 27, 2025
Updated: 2017
Stabond MR3
Technical Data Sheet
DESCRIPTION
Stabond Mold Release #3 has been developed to facilitate the removal of polyurethane parts from a mold.
PROPERTIES
TYPE: WAX SHELF LIFE: 12 MONTHS
COLOR: WHITE THINNER: STABOND T-THINNER
SOLIDS: 10% VISCOSITY: VERY THIN SYRUP
COVERAGE: 300 SQ. FT. /GALLON FLASH POINT: < 0 F
WT/GAL: 6.09 lbs
APPLICATION
The mold should be thoroughly cleaned and dried. Preheat the mold to 120 F. Either brush or spray the mold release to the warm,
dry surface. Then warm the mold and drive off the solvent by blowing air over the surface. The mold is now ready for use. Porous molds
e.g. Plaster of Paris, are not recommended, but if used, must first be sealed with lacquer or similar coating.
STORAGE
For maximum shelf life, store material in cool dry area and keep container tightly sealed. Storage temperature of 60 -80 F. is
recommended. Lower storage temperature will cause a temporary increase in viscosity. Rotate stock on a First in First out basis. For
optimum results agitate adhesive prior to use.
DANGER
Extremely flammable. Toxic. Vapors may ignite explosively. Provide fresh air cross ventilation to prevent build-up of vapors. Keep away
from heat, sparks and from open flame. Do not smoke. Extinguish all flames and pilot lights and turn off all non-explosion proof
electrical equipment and sources of ignition during use and until vapors are dissipated. Avoid prolonged or repeated breathing of
vapors. Close container after use. Contains aromatic and aliphatic hydrocarbons. KEEP OUT OF REACH OF CHILDREN. Harmful or fatal
if swallowed. If swallowed do not induce vomiting, seek immediate medical attention. THOROUGHLY READ THE SDS FOR THIS
PRODUCT PRIOR TO USING IT.
IMPORTANT
Suggestions for the use of this product are based on tests believed to be reliable; however, the user should determine suitability for
the intended use by his own evaluation. Because the use of the material is beyond our control, neither the seller nor the manufacturer
shall be liable for any injury, loss, or damage, direct or consequential, arising out of the use or inability to use this product. Seller and
manufacturer s sole obligation shall be replacement of material proved to be defective.
by | Sep 27, 2025
1.
Chem-Trend L.P.
1445 W. McPherson Park Drive, P.O. Box 860, Howell, MI 48844.0860
Telephone: 517.546.4520 Facsimile: 517.548.5370 US/Canada: 800.727.7730
Copyright 2004 Chem-Trend L.P., All Rights Reserved
040107
www.chemtrend.com
Chemlease
MPP2180 Sealer
Mold Prep and Primer
Chemlease
MPP2180 is formulated for sealing tooling in
both the FRP and advanced composites sectors.
Appropriate substrates include polyester gelcoat and non-
gelcoat, epoxy and phenolic mold surfaces, and most metals.
Chemlease
MPP2180 is not recommended for sealing
monolithic graphite or ceramic tooling.
General
Chemlease
MPP2180 should be applied onto a clean mold
surface. Chemlease
MPP2180 is an excellent sealing
material, but should not be used as a mold release agent.
Use of this product without a release agent may result in
severe damage to the mold. It has the ability to enhance the
performance of semi-permanent release agents. In many
cases, it has also been used as a means of re-surfacing a
worn-out mold. The appropriate Chemlease
releasant
should be applied on top of the product after it has been
cured. For sealing purposes, a wipe on/wipe off application
technique is used. To resurface a mold, use of a wipe
on/leave on technique is typical.
Mold Preparation
1.After the mold has been buffed and polished wi
th
rubbing and polishing compounds, wash t
he mold
surface thoroughly with clean water. The proper
water
wash will remove all fillers and wate
r-soluble
contaminants from the buffing an
d polishing
compounds. Use liberal amounts of water. Wipe dry
with clean cotton
cloths.
2.
Following the water wash, apply Chemlease
Mold
Cleaner to remove
all traces of solvent-soluble
contaminants such as waxes, silicones, oils, etc.
Use
liberal quantities of Mold Cleaner in a we
ll-ventilated
area, then wipe dry with clean cott
on cloths until the
mold is squeaky clean by thumb or hand rub test.
3.The wiping cloth should be changed regularly to e
nsure
that a clean, absorbent surface of the wi
ping cloth is
always presented to the mold surface. This proce
dure
prevents recontamination of the mold by wi
ping cloths
which carry cont
aminants lifted from the mold.
Application Instructions Wipe On/Leave On
1. Apply Chemlease
MPP2180 by wiping. Use clean, soft
cotton cloths. A wipe on/leave on
technique can be
used, even for Class A finish molds, applying to an
area of about four square feet at a time. Care shou
ld be
taken on large structures to ensure that the overla
p area
is as small as possible and that the product on the
area
overlapped has not already cured. Generally, 1 or
2
coats are sufficient to seal. Allow 30 minutes bet
ween
each coat. After the final coat, allow a 1-2 hour cu
re at
room temperature. The cure time can be reduced
to 20
minutes by warming mold to 120-140 F/49-60 C.
Note:
a prismatic sheen may develop on the mold surfac
e
using this method. This sheen does not imprint ont
o the
molded part in mo
st situations.
2.
When the product has cured, apply the appropriate
Chemlease
mold release. Please refer to the proper
Product Data Sheet for mold re
lease application details
and instructions.
Application Instructions Wipe On/ Wipe Off
Follow instructions for Wipe On/Leave On. However, after
material is wiped on, wipe off immediately using a clean, dry,
soft cotton cloth being careful to wipe off evenly. Change
cloths frequently for best results. Once material has begun to
dry and cure, it will not be possible to wipe off without
causing blemishes and streaks so it is important to wipe the
sealer off immediately after it has been wiped on and is still
wet. Generally, 1 or 2 wipe on/wipe off coats are sufficient to
seal.
Touch-Up Coats
Touch-up coats are not possible once this product is applied
and cured since a release agent must be applied over the top
of it before the mold can be used in production.
Cure Test
Under the best conditions, Chemlease
MPP2180 has been
found to cure in as little as one hour. A simple test method
for complete cure is: Apply one drop each of water and
Chemlease
Mold Cleaner onto a flange area that has been
coated with the product. Wait a few seconds then wipe off
with a clean cloth. If there is no evidence of the drops on the
tool surface, the product is completely cured.
Important
The recommended number of coats and cure times are a
general guideline found to be sufficient in a broad spectrum
of molding conditions. When molding products with extreme
geometries or experiencing low-humidity conditions in the
shop, the customer may find it necessary to extend the cure
time between coats and increase the number of coats applied
to the mold. The efficiency of a release film is best
determined through a combination of tape tests and
experimentation.
Storage
The container should be kept closed at all times when not in
use to prevent contamination, evaporation and/or premature
curing. Do not store at temperatures above 100 F/38 C.
Chemlease
MPP2180 is flammable. Keep away from heat,
sparks, flames and combustion sources during storage and
use. If stored in cold temperatures, allow to warm to room
temperature before using.
Packaging
Chemlease
MPP2180 is available in 1-quart (1-liter), 1-
gallon (4-liter), 5-gallon (20-liter) and 55-gallon (208-liter)
containers.
Safety Data
Material Safety Data Sheets are available for all
Chemlease
products and should be consulted prior to use
of the product.
While the technical information and suggestions for use contained
herein are believed to be accurate and reliable, nothing stated in this
bulletin is to be taken as a warranty either expressed or implied.
Chemlease
MPP2180
Mold Prep and Primer
