37WA910FD5_SDS.pdf
37WA315_SDS.pdf
SAFETY DATA SHEET
1. Identification
Product identifier
Other means of identification
Product code
Recommended use
TR-307, TR-307SP, TR-309, TR-315 Rubbing Compound
MR307, MR307SP, MR309, MR315
Industrial use polish.
Workers (and your customers or users in the case of resale) should be informed of the potential
presence of respirable dust and respirable crystalline silica as well as their potential hazards.
Appropriate training in the proper use and handling of this material should be provided as required
under applicable regulations.
Recommended restrictions
Manufacturer/Importer/Supplier/Distributor information
TR Industries a Division of Granitize Products Inc.Company name
11022 Vulcan StreetAddress
South Gate, CA 90280-0893
United States
(562) 923-5438Telephone
CHEMTREC: (800) 424-9300Emergency telephone
CHEMTREC International: 00 1-703-527-3887
2. Hazard(s) identification
Not classified.Physical hazards
Category 2Skin corrosion/irritationHealth hazards
Category 2Serious eye damage/eye irritation
Category 1ACarcinogenicity (inhalation)
Category 3 narcotic effectsSpecific target organ toxicity, single exposure
Category 2 (lungs)Specific target organ toxicity, repeated
exposure (inhalation)
Not classified.OSHA defined hazards
Label elements
Signal word Danger
Hazard statement Causes skin irritation. Causes serious eye irritation. May cause drowsiness or dizziness. May
cause cancer by inhalation. May cause damage to organs (lungs) through prolonged or repeated
exposure by inhalation.
Precautionary statement
Prevention Obtain special instructions before use. Do not handle until all safety precautions have been read
and understood. Do not breathe dust/fume/gas/mist/vapors/spray. Wash thoroughly after
handling. Use only outdoors or in a well-ventilated area. Wear protective gloves/protective
clothing/eye protection/face protection.
Response If on skin: Wash with plenty of water. If inhaled: Remove person to fresh air and keep comfortable
for breathing. If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses,
if present and easy to do. Continue rinsing. If exposed or concerned: Get medical
advice/attention. If skin irritation occurs: Get medical advice/attention. If eye irritation persists: Get
medical advice/attention. Take off contaminated clothing and wash it before reuse.
Storage Store in a well-ventilated place. Keep container tightly closed. Store locked up.
Disposal Dispose of contents/container in accordance with local/regional/national/international regulations.
Hazard(s) not otherwise
classified (HNOC)
None known.
SDS US
TR-307, TR-307SP, TR-309, TR-315 Rubbing Compound
3627 Version #: 08 Revision date: – 15-September-2022 Issue date: 17-December-2014 1 / 8
Supplemental information None.
3. Composition/information on ingredients
Mixtures
7732-18-5 35 – 40Water
CAS number %Chemical name
64742-47-8 30 – 35Petroleum distillates
14808-60-7 15 – 20Quartz
61790-12-3 5 – 10Fatty acids, tall oil
8002-09-3 1 – 5Pine Oil
141-43-5 1 – < 32-Aminoethanol
All concentrations are in percent by weight unless otherwise indicated.Composition comments
4. First-aid measures
Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a poison
center or doctor/physician if you feel unwell.
Inhalation
Remove contaminated clothing. Wash with plenty of soap and water. If skin irritation occurs: Get
medical advice/attention. Wash contaminated clothing before reuse.
Skin contact
Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if
present and easy to do. Continue rinsing. Get medical attention if irritation develops and persists.
Eye contact
Rinse mouth. Do not induce vomiting without advice from poison control center. If vomiting occurs,
keep head low so that stomach content doesn't get into the lungs. Get medical attention if
symptoms occur.
Ingestion
May cause drowsiness and dizziness. Headache. Nausea, vomiting. Severe eye irritation.
Symptoms may include stinging, tearing, redness, swelling, and blurred vision. Skin irritation. May
cause redness and pain. Prolonged exposure may cause chronic effects.
Most important
symptoms/effects, acute and
delayed
Provide general supportive measures and treat symptomatically. Keep victim under observation.
Symptoms may be delayed.
Indication of immediate
medical attention and special
treatment needed
IF exposed or concerned: Get medical advice/attention. If you feel unwell, seek medical advice
(show the label where possible). Ensure that medical personnel are aware of the material(s)
involved, and take precautions to protect themselves.
General information
5. Fire-fighting measures
Alcohol resistant foam. Powder. Dry chemicals. Carbon dioxide (CO2).Suitable extinguishing media
Do not use water jet as an extinguisher, as this will spread the fire.Unsuitable extinguishing
media
During fire, gases hazardous to health may be formed.Specific hazards arising from
the chemical
Self-contained breathing apparatus and full protective clothing must be worn in case of fire.Special protective equipment
and precautions for firefighters
In case of fire and/or explosion do not breathe fumes. Move containers from fire area if you can do
so without risk. Cool containers exposed to flames with water until well after the fire is out.
Fire fighting
equipment/instructions
Use standard firefighting procedures and consider the hazards of other involved materials.Specific methods
Will burn if involved in a fire.General fire hazards
6. Accidental release measures
Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Wear
appropriate protective equipment and clothing during clean-up. Do not touch damaged containers
or spilled material unless wearing appropriate protective clothing. Ensure adequate ventilation.
Local authorities should be advised if significant spillages cannot be contained. For personal
protection, see section 8 of the SDS.
Personal precautions,
protective equipment and
emergency procedures
SDS US
TR-307, TR-307SP, TR-309, TR-315 Rubbing Compound
3627 Version #: 08 Revision date: - 15-September-2022 Is
sue date: 17-December-2014
2 / 8
Prevent product from entering drains.
Large Spills: Stop the flow of material, if this is without risk. Dike the spilled material, where this is
possible. Absorb in vermiculite, dry sand or earth and place into containers. Following product
recovery, flush area with water.
Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to
remove residual contamination.
Never return spills to original containers for re-use. Put material in suitable, covered, labeled
containers. For waste disposal, see section 13 of the SDS.
Methods and materials for
containment and cleaning up
Avoid release to the environment.Environmental precautions
7. Handling and storage
Obtain special instructions before use. Do not handle until all safety precautions have been read
and understood. Keep formation of airborne dusts to a minimum. Provide appropriate exhaust
ventilation at places where dust is formed. Do not breathe dust/fume/vapors. Do not get in eyes,
on skin, or on clothing. Avoid prolonged or repeated contact with skin. Should be handled in closed
systems, if possible. Use only in well-ventilated areas. Wear appropriate personal protective
equipment. Avoid release to the environment. Observe good industrial hygiene practices.
Precautions for safe handling
Keep away from heat and sources of ignition. Store in tightly closed container. Store away from
incompatible materials (see Section 10 of the SDS).
Conditions for safe storage,
including any incompatibilities
8. Exposure controls/personal protection
Occupational exposure limits
US. OSHA Specifically Regulated Substances (29 CFR 1910.1001-1053)
ValueComponents Type
TWA 0.05 mg/m3Quartz (CAS 14808-60-7)
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
ValueComponents Type
PEL 6 mg/m32-Aminoethanol (CAS
141-43-5)
3 ppm
US. OSHA Table Z-3 (29 CFR 1910.1000)
FormValueComponents Type
TWA 0.1 mg/m3 Respirable.Quartz (CAS 14808-60-7)
2.4 mppcf Respirable.
US. ACGIH Threshold Limit Values
FormValueComponents Type
STEL 6 ppm2-Aminoethanol (CAS 141-43-5)
TWA 3 ppm
TWA 0.025 mg/m3 Respirable fraction.Quartz (CAS 14808-60-7)
US. NIOSH: Pocket Guide to Chemical Hazards
Form
ValueComponents Type
STEL 15 mg/m32-Aminoethanol (CAS
141-43-5)
6 ppm
TWA 8 mg/m3
3 ppm
TWA 100 mg/m3Petroleum distillates (CAS
64742-47-8)
TWA 0.05 mg/m3 Respirable dust.Quartz (CAS 14808-60-7)
No biological exposure limits noted for the ingredient(s).Biological limit values
SDS US
TR-307, TR-307SP, TR-309, TR-315 Rubbing Compound
3627 Version #: 08 Revision date: - 15-September-2022 Is
sue date: 17-December-2014
3 / 8
Good general ventilation should be used. Ventilation rates should be matched to conditions. If
applicable, use process enclosures, local exhaust ventilation, or other engineering controls to
maintain airborne levels below recommended exposure limits. Provide easy access to water
supply and eye wash facilities.
Appropriate engineering
controls
Individual protection measures, such as personal protective equipment
Wear safety glasses with side shields (or goggles). Wear face shield if there is risk of splashes.Eye/face protection
Skin protection
Wear appropriate chemical resistant gloves. Be aware that the liquid may penetrate the gloves.
Frequent change is advisable. Nitrile or neoprene gloves are recommended. Other suitable gloves
can be recommended by the glove supplier.
Hand protection
Skin protection
Wear appropriate chemical resistant clothing. Use of an impervious apron is recommended.Other
If engineering controls do not maintain airborne concentrations below recommended exposure
limits (where applicable) or to an acceptable level (in countries where exposure limits have not
been established), an approved respirator must be worn. Check with respiratory protective
equipment suppliers.
Respiratory protection
Wear appropriate thermal protective clothing, when necessary.Thermal hazards
Observe any medical surveillance requirements. Always observe good personal hygiene
measures, such as washing after handling the material and before eating, drinking, and/or
smoking. Routinely wash work clothing and protective equipment to remove contaminants.
General hygiene
considerations
9. Physical and chemical properties
Appearance
Solid.Physical state
Paste.Form
Not available.Color
Not available.Odor
Odor threshold Not available.
pH Not applicable.
Melting point/freezing pointNot available.
Initial boiling point and boiling
range
Not available.
Flash point > 140.0 F (> 60.0 C) (Estimated)
Evaporation rate Not applicable.
Will burn if involved in a fire.Flammability (solid, gas)
Upper/lower flammability or explosive limits
Flammability limit – lower
(%)
Not available.
Flammability limit – upper
(%)
Not available.
Vapor pressure Not applicable.
Vapor density Not applicable.
Relative density Not available.
Solubility(ies)
Solubility (water) Not available.
Partition coefficient
(n-octanol/water)
Not available.
Auto-ignition temperature Not available.
Decomposition temperature Not available.
Viscosity Not applicable.
Other information
Not explosive.Explosive properties
Not oxidizing.Oxidizing properties
SDS US
TR-307, TR-307SP, TR-309, TR-315 Rubbing Compound
3627 Version #: 08 Revision date: – 15-September-2022 Is
sue date: 17-December-2014
4 / 8
10. Stability and reactivity
The product is stable and non-reactive under normal conditions of use, storage and transport.Reactivity
Material is stable under normal conditions.Chemical stability
Hazardous polymerization does not occur.Possibility of hazardous
reactions
Contact with incompatible materials.Conditions to avoid
Strong oxidizers, strong acids, and strong bases. Chlorine.Incompatible materials
Thermal decomposition of this product can generate carbon monoxide and carbon dioxide.
Nitrogen oxides. Silicon oxide fumes.
Hazardous decomposition
products
11. Toxicological information
Information on likely routes of exposure
Inhalation May cause damage to organs through prolonged or repeated exposure by inhalation. May cause
drowsiness and dizziness. May cause cancer by inhalation.
Skin contact Causes skin irritation. May be absorbed through the skin.
Prolonged or repeated exposure may cause liver and kidney damage. These effects have not
been observed in humans.
Eye contac
t Causes serious eye irritation.
Ingestion May cause discomfort if swallowed.
Symptoms related to the
physical, chemical and
toxicological characteristics
May cause drowsiness and dizziness. Headache. Nausea, vomiting. Severe eye irritation.
Symptoms may include stinging, tearing, redness, swelling, and blurred vision. Skin irritation. May
cause redness and pain. Prolonged exposure may cause chronic effects.
Information on toxicological effects
Acute toxicit
y Not expected to be acutely toxic.
Test ResultsComponents Species
2-Aminoethanol (CAS 141-43-5)
Dermal
Acute
LD50 Rabbit 1025 mg/kg
Oral
LD50 Rat 1089 mg/kg
Quartz (CAS 14808-60-7)
Inhalation
Chronic
LOEC Human 0.0563 mg/m3
Causes skin irritation.Skin corrosion/irritation
Causes serious eye irritation.Serious eye damage/eye
irritation
Respiratory or skin sensitization
Respiratory sensitizationNot a respiratory sensitizer.
This product is not expected to cause skin sensitization.Skin sensitization
No data available to indicate product or any components present at greater than 0.1% are
mutagenic or genotoxic.
Germ cell mutagenicity
Carcinogenicity May cause cancer.
Occupational exposure to respirable dust and respirable crystalline silica should be monitored and
controlled.
IARC Monographs. Overall Evaluation of Carcinogenicity
Quartz (CAS 14808-60-7) 1 Carcinogenic to humans.
NTP Report on Carcinogens
Quartz (CAS 14808-60-7) Known To Be Human Carcinogen.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1053)
Quartz (CAS 14808-60-7) Cancer
SDS US
TR-307, TR-307SP, TR-309, TR-315 Rubbing Compound
3627 Version #: 08 Revision date: – 15-September-2022 Is
sue date: 17-December-2014
5 / 8
This product is not expected to cause reproductive or developmental effects.Reproductive toxicity
Specific target organ toxicity –
single exposure
May cause drowsiness and dizziness.
Specific target organ toxicity –
repeated exposure
May cause damage to organs (lungs) through prolonged or repeated exposure by inhalation.
Aspiration hazard Not an aspiration hazard.
Chronic effects May cause damage to organs through prolonged or repeated exposure. May be harmful if
absorbed through skin. Prolonged exposure may cause chronic effects.
Prolonged or repeated exposure may cause liver and kidney damage. These effects have not
been observed in humans.
Further information Symptoms may be delayed.
12. Ecological information
Not expected to be harmful to aquatic organisms.Ecotoxicity
Components Test ResultsSpecies
2-Aminoethanol (CAS 141-43-5)
Aquatic
Acute
EC50Algae 2.8 mg/l, 72 HoursPseudokirchnerella subcapitata
EC50Crustacea 32.6 mg/l, 48 HoursDaphnia magna
LC50Fish 150 mg/l, 96 HoursOncorhynchus mykiss
Chronic
EC50Crustacea 2.52 mg/l, 21 daysDaphnia magna
Petroleum distillates (CAS 64742-47-8)
Aquatic
Acute
LC50Fish 2.9 mg/l, 96 hoursRainbow trout,donaldson trout (Oncorhynchus mykiss)
No data is available on the degradability of this product.Persistence and degradability
Bioaccumulative potential
Partition coefficient n-octanol / water (log Kow)
2-Aminoethanol (CAS 141-43-5) -1.31
No data available for this product.Mobility in soil
Other adverse effects The product contains volatile organic compounds which have a photochemical ozone creation
potential.
13. Disposal considerations
Collect and reclaim or dispose in sealed containers at licensed waste disposal site. Incinerate the
material under controlled conditions in an approved incinerator. Do not allow this material to drain
into sewers/water supplies. Do not contaminate ponds, waterways or ditches with chemical or used
container. Dispose of contents/container in accordance with local/regional/national/international
regulations.
Disposal instructions
Dispose in accordance with all applicable regulations.Local disposal regulations
The waste code should be assigned in discussion between the user, the producer and the waste
disposal company.
Hazardous waste code
Dispose of in accordance with local regulations. Empty containers or liners may retain some
product residues. This material and its container must be disposed of in a safe manner.
Waste from residues / unused
products
Since emptied containers may retain product residue, follow label warnings even after container is
emptied. Empty containers should be taken to an approved waste handling site for recycling or
disposal.
Contaminated packaging
14. Transport information
DOT
Not regulated as dangerous goods.
SDS US
TR-307, TR-307SP, TR-309, TR-315 Rubbing Compound
3627 Version #: 08 Revision date: – 15-September-2022 Is
sue date: 17-December-2014
6 / 8
IATA
Not regulated as dangerous goods.
IMDG
Not regulated as dangerous goods.
Not applicable.Transport in bulk according to
Annex II of MARPOL 73/78 and
the IBC Code
15. Regulatory information
This product is a “Hazardous Chemical” as defined by the OSHA Hazard Communication
Standard, 29 CFR 1910.1200.
US federal regulations
TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)
Not regulated.
CERCLA Hazardous Substance List (40 CFR 302.4)
Not listed.
SARA 304 Emergency release notification
Not regulated.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1053)
Quartz (CAS 14808-60-7) Cancer
lung effects
immune system effects
kidney effects
Toxic Substances Control Act (TSCA) All components of the mixture on the TSCA 8(b) inventory are designated
active .
SARA 302 Extremely hazardous substance
Superfund Amendments and Reauthorization Act of 1986 (SARA)
Not listed.
YesSARA 311/312 Hazardous
chemical
Skin corrosion or irritation
Serious eye damage or eye irritation
Carcinogenicity
Specific target organ toxicity (single or repeated exposure)
Classified hazard
categories
SARA 313 (TRI reporting)
Not regulated.
Other federal regulations
Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List
Not regulated.
Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)
Not regulated.
Not regulated.Safe Drinking Water Act
(SDWA)
US state regulations
US. Massachusetts RTK – Substance List
2-Aminoethanol (CAS 141-43-5)
Petroleum distillates (CAS 64742-47-8)
Quartz (CAS 14808-60-7)
US. New Jersey Worker and Community Right-to-Know Act
2-Aminoethanol (CAS 141-43-5)
Petroleum distillates (CAS 64742-47-8)
Pine Oil (CAS 8002-09-3)
Quartz (CAS 14808-60-7)
US. Pennsylvania Worker and Community Right-to-Know Law
2-Aminoethanol (CAS 141-43-5)
Petroleum distillates (CAS 64742-47-8)
Quartz (CAS 14808-60-7)
SDS US
TR-307, TR-307SP, TR-309, TR-315 Rubbing Compound
3627 Version #: 08 Revision date: – 15-September-2022 Is
sue date: 17-December-2014
7 / 8
US. Rhode Island RTK
2-Aminoethanol (CAS 141-43-5)
Petroleum distillates (CAS 64742-47-8)
Quartz (CAS 14808-60-7)
California Proposition 65
This product can expose you to Quartz, which is known to the State of California to cause cancer.
For more information go to www.P65Warnings.ca.gov.
WARNING:
California Proposition 65 – CRT: Listed date/Carcinogenic substance
Quartz (CAS 14808-60-7) Listed: October 1, 1988
US. California. Candidate Chemicals List. Safer Consumer Products Regulations (Cal. Code Regs, tit. 22, 69502.3,
subd. (a))
Petroleum distillates (CAS 64742-47-8)
Quartz (CAS 14808-60-7)
International Inventories
Country(s) or region Inventory name On inventory (yes/no)*
Australian Inventory of Chemical Substances (AICS) YesAustralia
Domestic Substances List (DSL) YesCanada
Non-Domestic Substances List (NDSL) NoCanada
Inventory of Existing Chemical Substances in China (IECSC) YesChina
European Inventory of Existing Commercial Chemical
Substances (EINECS)
NoEurope
European List of Notified Chemical Substances (ELINCS) NoEurope
Inventory of Existing and New Chemical Substances (ENCS) NoJapan
Existing Chemicals List (ECL) YesKorea
New Zealand Inventory YesNew Zealand
Philippine Inventory of Chemicals and Chemical Substances
(PICCS)
YesPhilippines
Taiwan Chemical Substance Inventory (TCSI) YesTaiwan
*A “Yes” indicates this product complies with the inventory requirements administered by the governing country(s).
A “No” indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing
country(s).
Toxic Substances Control Act (TSCA) Inventory YesUnited States & Puerto Rico
16. Other information, including date of preparation or last revision
Issue date
Revision date
Version #
17-December-2014
15-September-2022
08
NFPA ratings
02
1
TR Industries cannot anticipate all conditions under which this information and its product, or the
products of other manufacturers in combination with its product, may be used. It is the user s
responsibility to ensure safe conditions for handling, storage and disposal of the product, and to
assume liability for loss, injury, damage or expense due to improper use. The information in the
sheet was written based on the best knowledge and experience currently available.
Disclaimer
SDS US
TR-307, TR-307SP, TR-309, TR-315 Rubbing Compound
3627 Version #: 08 Revision date: – 15-September-2022 Is
sue date: 17-December-2014
8 / 8
37WA171_SDS.pdf
In case of emergency or spill, contact CHEMTREC at 800-424-9300
MATERIAL SAFETY DATA SHEET
1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND THE
COMPANY/UNDERTAKING
Product Name: M20 – Polymer Sealant
Use of the Substance/Preparation
Recommended use: Protective Coating
Company/Undertaking Identification
2. HAZARDS IDENTIFICATION
Most important hazards: This product contains chemicals listed on Canada WHMIS. See Section 15.
3. COMPOSITION/INFORMATION ON INGREDIENTS
Hazardous Ingredients
Components CAS # % Weight OSHA PEL
TWA
EINECS No. Classification
Light Distillate 64742-14-9 10-15 None — —
Kaolin 1332-58-7 8-12 10mg/m
3
310-194-1 R42
Isoparaffinic Hydrocarbon 64742-48-9 15-25 None 265-150-3 Xn; R-65
Hydrotreated Distillate 64742-46-7 1-5 None — —
4. FIRST AID MEASURES
General Advice: In the case of accident or if you feel unwell, seek medical advice immediately (show
the label where possible).
Inhalation: Prolonged or intentional exposure to high concentrations may cause respiratory track
irritation. Move to fresh air. Consult a physician.
Page 1/5
Meguiar’s UK Ltd.
3 Lamport Court
Heartlands
Daventry NN11 8UF
Tel: 0870 241 6696
Fax: 01327 300 116
Meguiar’s USA
17991 Mitchell South
Irvine, CA 92614
Tel: 949-752-8000
Fax: 949-752-5784
Print date: 03/25/2009
Reference Number:
18-122B Prepared Date: 03/25/2009
Meguiar’s Holland
Laan der Verenigde Naties 40
33174 DA Dordrecht
Holland
Tel: 31-78-6210268 Meguiar’s Hong Kong
Suite 6-7, 20/F Marina House
68 Hing Man Street
Shaukeiwan
Hong Kong
Tel: 852-2967-0202
Meguiar’s France 3 rud de Verdun – B t. D 78590 Noisy Le Roi France Tel: 33-1-30-80-02-16
Skin contact: Wash off immediately with soap and plenty of water. If skin irritation persists, call a
physician.
Eye contact: Flush eyes with water as a precaution. If symptoms persist, call a physician
Ingestion: Rinse mouth. Drink 1 or 2 glasses of water. Consult a physician if necessary.
5. FIRE-FIGHTING MEASURES
NFPA:
Suitable extinguishing media: Use dry chemical, CO2, water spray or alcohol-resistant foam.
Specific hazards: Not applicable
Special protective equipment for firefighters: As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH (approved or equivalent) and full protective gear.
Extinguishing media which must not be used for safety reasons: Not applicable
Specific methods: Not applicable
6. ACCIDENTAL RELEASE MEASURES
Personal precautions: Ensure adequate ventilation.
Environmental precautions: Do not allow material to contaminate ground water system.
Methods for cleaning up: Wipe up with absorbent material (e.g. cloth, fleece).
7. HANDLING AND STORAGE
Handling:
Technical measures/precautions:
Use only in area well ventilated area
Safe handling advice:
None under normal processing
Storage:
Store at room temperature in the original container. Keep away from direct sunlight. Do not freeze.
Incompatible products:
Do not store together with acids or oxidizers.
Page 2/5
Flammability: 2Health: 1 Reactivity: 0
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Engineering measures to reduce
exposure:
Ensure adequate ventilation..
Respiratory protection: No personal respiratory protective equipment normally required.
Skin and body protection: No special precautions required..
Eye protection: Avoid contact with eyes. If splashes are likely to occur, wear:. Goggles.
Hand protection: Preventative skin protection:. Neoprene Gloves..
9. PHYSICAL AND CHEMICAL PROPERTIES
General Information
Important Health Safety and Environmental Information
pH @70 F: 9.00
Flash point: 200 ( F), 93 ( C ) Method: PMCC-ASTM D93-90
Boiling point/range: 390 ( F), 199 ( C)
Water Solubility: Moderately soluble
Vapor density: >1
Specific gravity: 1.00
Evaporation rate: <1
VOC content: 24% max.
10. STABILITY AND REACTIVITY
Stability: Stable under recommended storage conditions.
Polymerization: None under normal processing.
Conditions to avoid: Extremes of temperature and direct sunlight
Materials to avoid: Strong acids and strong bases, Strong oxidizing agents
Hazardous decomposition products: None reasonably foreseeable
11. TOXICOLOGICAL INFORMATION
Component Information
Additional Information: The product is not subject to classification according to the calculation method of the
General EC Classification Guidelines for Preparations as issued in the latest version.
When used and handled according to specifications, the product does not have any
harmful effects according to our experience and the information provided to us.
12. ECOLOGICAL INFORMATION
Ecotoxicity
Page 3/5
Liquid
Color: White
Appearance:
Odor: Sweet
Physical state: Liquid
Product Information
Aquatic toxicity: No information available
Component Information
Ecotoxicity effects: Not determined
13. DISPOSAL CONSIDERATIONS
Waste from residues / unused products:
Waste disposal must be in accordance with appropriate Federal, State, and local regulations. This product, if unaltered by
use, may be disposed of by treatment at a permitted facility or as advised by your local hazardous waste regulatory
authority.
Contaminated packaging:
Disposal must be made according to local and federal regulations.
Ewc waste disposal no:
Not applicable
Further information
According to the European Waste Catalogue, Waste Codes are not product specific, but application specific
14. TRANSPORT INFORMATION
General Transportation Statement This product does not require classification by DOT, IATA,
ICAO or IMDG.
Other information:
The description shown may not apply to all shipping situations. Consult 49CFR, or appropriate Dangerous Goods
Regulations, for additional description requirements and mode-specific or quantity-specific shipping requirements.
15. REGULATORY INFORMATION
Components TSCA DSL/NDSL Canada - WHMIS Classification
Kaolin 1332-58-7 Present Present D2B
Isoparaffinic Hydrocarbon 64742-48-9 Present Present
Hydrotreated Distillate 64742-46-7 Present Present
CERCLA/SARA 313 Emission reporting
None
16. OTHER INFORMATION
Prepared by: Health & Safety
Literary reference: None
Page 4/5
Disclaimer: To the best of our knowledge, the information contained herein is accurate. However,
neither the above named supplier nor any of its subsidiaries assumes any liability
whatsoever for the accuracy or completeness of the information contained herein.
Final determination of suitability of any material is the sole responsibility of the user.
All materials may present unknown hazards and should be used with caution.
Although certain hazards are described herein, we cannot guarantee that these are
the only hazards that exist
End of Safety Data Sheet
Page 5/5
37WA170_SDS.pdf
SAFETY DATA SHEET
1. Identification
Product identifier Gel Gloss GG-1, GG-8, GG-64, GG-128
Other means of identificationNot available.
Recommended use Surface gloss.
Recommended restrictions None known.
Manufacturer/Importer/Supplier/Distributor information
Manufacturer/Supplier TR Industries a Division of Granitize Products Inc.
Address 11022 Vulcan Street
South Gate, CA 90280-0893 United States
Telephone: (562) 923-5438
Emergency CHEMTREC: (800) 424-9300
CHEMTREC International: 00 1-703-527-3887
2. Hazard(s) identification
Category 3Flammable LiquidsPhysical hazards
Category 2Skin corrosion/irritationHealth Hazards
Category 1Serious eye damage/eye irritation
Category 1Sensitization, skin
Category 1Aspiration hazard
Category 2Hazardous to the aquatic environment,
long-term hazard
Environmental hazards
Not classified.OSHA defined hazards
Label elements
Signal word Danger
Hazard statement Flammable liquid and vapor. May be fatal if swallowed and enters airways. Causes skin irritation.
Causes serious eye damage. Toxic to aquatic life with long lasting effects. May cause an allergic
skin reaction.
Precautionary statement
Prevention Keep away from heat/sparks/open flames/hot surfaces. – No smoking. Keep container tightly
closed. Ground/bond container and receiving equipment. Use explosion-proof
electrical/ventilating/lighting equipment. Use only non-sparking tools. Take precautionary
measures against static discharge. Avoid breathing mist or vapor. Contaminated work clothing
must not be allowed out of the workplace. Avoid release to the environment. Wear protective
gloves/protective clothing/eye protection/face protection.
Response If swallowed: Immediately call a poison center/doctor. Do NOT induce vomiting. If on skin (or hair):
Take off immediately all contaminated clothing. Rinse skin with water/shower. If skin irritation
occurs: Get medical advice/attention. Take off contaminated clothing and wash before reuse. If in
eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy
to do. Continue rinsing. Immediately call a poison center/doctor. Collect spillage.
Storage Store in a well-ventilated place. Keep cool. Store locked up.
Disposal Dispose of contents/container in accordance with local/regional/national/international regulations.
Hazard(s) not otherwise
classified (HNOC)
None known.
3. Composition/information on ingredients
Mixtures
Gel Gloss GG-1, GG-8, GG-64, GG-128 SDS US
922736 Version #: 01 Revision date: – Issue date: 15-September-2014
1 / 9
5989-27-5 1 – 5D-Limonene
CAS number %Chemical name
68551-19-9 30-35C12-C14 isoalkanes
112-80-1 1-5Oleic acid
14808-60-7 1-5Quartz
110-91-8 <5Morpholine
Composition comments All concentrations are in percent by weight unless ingredient is a gas. Gas concentrations are in
percent by volume. Components not listed are either non-hazardous or are below reportable
limits.
4. First-aid measures
Inhalation Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON
CENTER or doctor/physician if you feel unwell.
Skin contact Take off immediately all contaminated clothing. Rinse skin with water/shower. If skin irritation
occurs: Get medical advice/attention. Wash contaminated clothing before reuse.
Eye contact Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if
present and easy to do. Continue rinsing. Get medical attention immediately.
Ingestion Call a physician or poison control center immediately. Rinse mouth. Do not induce vomiting. If
vomiting occurs, keep head low so that stomach content doesn't get into the lungs. Never give
anything by mouth to an unconscious person.
Most important
symptoms/effects, acute and
delayed
Diarrhea. May cause drowsiness and dizziness. Headache. Nausea, vomiting. Irritation of nose
and throat. Aspiration may cause pulmonary edema and pneumonitis. Severe eye irritation.
Symptoms may include stinging, tearing, redness, swelling, and blurred vision. Permanent eye
damage including blindness could result. Skin irritation. May cause redness and pain. May cause
an allergic skin reaction.
Indication of immediate
medical attention and special
treatment needed
Provide general supportive measures and treat symptomatically. Thermal burns: Flush with water
immediately. While flushing, remove clothes which do not adhere to affected area. Call an
ambulance. Continue flushing during transport to hospital. Keep victim under observation.
Symptoms may be delayed.
General information Take off all contaminated clothing immediately. IF exposed or concerned: Get medical
advice/attention. If you feel unwell, seek medical advice (show the label where possible). Ensure
that medical personnel are aware of the material(s) involved, and take precautions to protect
themselves. Wash contaminated clothing before reuse.
5. Fire-fighting measures
Suitable extinguishing media Water fog. Foam. Dry chemical powder. Carbon dioxide (CO2).
Unsuitable extinguishing
media
Do not use a solid water stream as it may scatter and spread fire.
Specific hazards arising from
the chemical
Vapors may form explosive mixtures with air.
Thermal decomposition may produce CO, CO2, oxides of nitrogen and other potentially toxic
gases.
Special protective equipment
and precautions for firefighters
Wear full protective clothing, including helmet, self-contained positive pressure or pressure
demand breathing apparatus, protective clothing and face mask.
Fire fighting
equipment/instructions
Cool containers exposed to heat with water spray and remove container, if no risk is involved.
General fire hazards Flammable liquid and vapor. Heat may cause the containers to explode.
6. Accidental release measures
Personal precautions,
protective equipment and
emergency procedures
Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Keep out of
low areas. Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area).
Wear appropriate protective equipment and clothing during clean-up. Do not breathe mist or vapor.
Do not touch damaged containers or spilled material unless wearing appropriate protective
clothing. Ventilate closed spaces before entering them. Local authorities should be advised if
significant spillages cannot be contained. For personal protection, see section 8 of the SDS.
Gel Gloss GG-1, GG-8, GG-64, GG-128 SDS US
922736 Version #: 01 Revision date: - Issue date: 15-September-2014
2 / 9
Methods and materials for
containment and cleaning up
ELIMINATE all ignition sources (no smoking, flares, sparks or flames in immediate area). Take
precautionary measures against static discharge. Use only non-sparking tools. Keep combustibles
(wood, paper, oil, etc.) away from spilled material. Stop the flow of material, if this is without risk.
Dike the spilled material, where this is possible.
Large Spills: Use water spray to reduce vapors or divert vapor cloud drift. Cover with plastic sheet
to prevent spreading. Use a non-combustible material like vermiculite, sand or earth to soak up the
product and place into a container for later disposal. Prevent product from entering drains.
Following product recovery, flush area with water.
Small Spills: Absorb with earth, sand or other non-combustible material and transfer to containers
for later disposal. Clean surface thoroughly to remove residual contamination.
Never return spills to original containers for re-use. For waste disposal, see section 13 of the SDS.
Environmental precautions Avoid release to the environment. Prevent further leakage or spillage if safe to do so. Avoid
discharge into drains, water courses or onto the ground. Inform appropriate managerial or
supervisory personnel of all environmental releases.
7. Handling and storage
Precautions for safe handlingDo not handle, store or open near an open flame, sources of heat or sources of ignition. Protect
material from direct sunlight. When using do not smoke. Explosion-proof general and local exhaust
ventilation. Take precautionary measures against static discharges. All equipment used when
handling the product must be grounded. Use non-sparking tools and explosion-proof equipment.
Do not breathe mist or vapor. Do not get in eyes, on skin, or on clothing. Should be handled in
closed systems, if possible. Wear appropriate personal protective equipment. Wash hands
thoroughly after handling. Avoid release to the environment. Observe good industrial hygiene
practices.
Conditions for safe storage,
including any incompatibilities
Store locked up. Keep away from heat and sources of ignition. Store in a cool, dry place out of
direct sunlight. Store in original tightly closed container. Store in a well-ventilated place.
Refrigeration recommended. Keep out of the reach of children. Keep in an area equipped with
sprinklers. Store away from incompatible materials (see Section 10 of the SDS).
8. Exposure controls/personal protection
Occupational exposure limits
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
ValueTypeComponents PEL 70 mg/m3Morpholine (CAS 110-91-8)
20 ppm
US. OSHA Table Z-3 (29 CFR 1910.1000)
ValueType FormComponents
TWA 0.3 mg/m3 Total dust.Quartz (CAS 14808-60-7)
0.1 mg/m3 Respirable.
2.4 mppcf Respirable.
US. ACGIH Threshold Limit Values
ValueType FormComponents
TWA 20 ppmMorpholine (CAS 110-91-8)
TWA 0.025 mg/m3 Respirable fraction.Quartz (CAS 14808-60-7)
US. NIOSH: Pocket Guide to Chemical Hazards
ValueType FormComponents
STEL 105 mg/m3Morpholine (CAS 110-91-8)
30 ppm
TWA 70 mg/m3
20 ppm
TWA 0.05 mg/m3 Respirable dust.Quartz (CAS 14808-60-7)
US. Workplace Environmental Exposure Level (WEEL) Guides
ValueTypeComponents
TWA 165.5 mg/m3D-Limonene (CAS
5989-27-5)
Gel Gloss GG-1, GG-8, GG-64, GG-128 SDS US
922736 Version #: 01 Revision date: - Issue date: 15-September-2014
3 / 9
US. Workplace Environmental Exposure Level (WEEL) Guides
ValueTypeComponents
30 ppm
Biological limit values No biological exposure limits noted for the ingredient(s).
Exposure guidelines
US - California OELs: Skin designation
Morpholine (CAS 110-91-8) Can be absorbed through the skin.
US - Minnesota Haz Subs: Skin designation applies
Morpholine (CAS 110-91-8) Skin designation applies.
US - Tennessee OELs: Skin designation
Morpholine (CAS 110-91-8) Can be absorbed through the skin.
US ACGIH Threshold Limit Values: Skin designation
Morpholine (CAS 110-91-8) Can be absorbed through the skin.
US. NIOSH: Pocket Guide to Chemical Hazards
Morpholine (CAS 110-91-8) Can be absorbed through the skin.
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
Morpholine (CAS 110-91-8) Can be absorbed through the skin.
Appropriate engineering
controls
Use explosion-proof ventilation equipment. Use process enclosures, local exhaust ventilation, or
other engineering controls to control airborne levels below recommended exposure limits. Provide
eyewash station.
Individual protection measures, such as personal protective equipment
Eye/face protection Wear approved chemical safety goggles. Wear face shield if there is risk of splashes.
Skin protection
Hand protection Wear appropriate chemical resistant gloves.
Other Wear appropriate chemical resistant clothing. Use of an impervious apron is recommended.
Respiratory protection If engineering controls do not maintain airborne concentrations below recommended exposure
limits (where applicable) or to an acceptable level (in countries where exposure limits have not
been established), an approved respirator must be worn. Use a NIOSH/MSHA approved air
purifying respirator as needed to control exposure. Consult with respirator manufacturer to
determine respirator selection, use, and limitations. Use positive pressure, air-supplied respirator
for uncontrolled releases or when air purifying respirator limitations may be exceeded. Follow
respirator protection program requirements (OSHA 1910.134 and ANSI Z88.2) for all respirator
use.
Thermal hazards Wear appropriate thermal protective clothing, when necessary.
General hygiene
considerations
When using do not smoke. Always observe good personal hygiene measures, such as washing
after handling the material and before eating, drinking, and/or smoking. Routinely wash work
clothing and protective equipment to remove contaminants.
9. Physical and chemical properties
Appearance Milky white liquid.
Physical state Liquid.
Form Liquid.
Color Milky white.
Odor Characteristic.
Odor threshold Not available.
pH Not available.
Melting point/freezing pointNot available.
Initial boiling point and boiling
range
> 302 F (> 150 C)
Flash point 140.0 – 200.0 F (60.0 – 93.3 C)
Evaporation rate 0.1 Estimated.
Flammability (solid, gas) Not available.
Upper/lower flammability or explosive limits
Flammability limit – lower
(%)
Not available.
Gel Gloss GG-1, GG-8, GG-64, GG-128 SDS US
922736 Version #: 01 Revision date: – Issue date: 15-September-2014
4 / 9
Flammability limit – upper
(%)
Not available.
Explosive limit – lower (%)Not available.
Explosive limit – upper (%)Not available.
Vapor pressure Not available.
Vapor density 4.9 Estimated.
Relative density < 1 Estimated.
Solubility(ies)
Solubility (water) Negligible in water.
Partition coefficient
(n-octanol/water)
Not available.
Auto-ignition temperature Not available.
Decomposition temperature Not available.
Viscosity Not available.
Other information
Percent volatile < 65 %
10. Stability and reactivity
Reactivity The product is stable and non-reactive under normal conditions of use, storage and transport.
Chemical stability Material is stable under normal conditions.
Possibility of hazardous
reactions
No dangerous reaction known under conditions of normal use.
Conditions to avoid Avoid heat, sparks, open flames and other ignition sources. Avoid temperatures exceeding the
flash point. Contact with incompatible materials.
Incompatible materials Strong oxidizing agents. Strong acids. Strong bases. Amines.
Hazardous decomposition
products
No hazardous decomposition products are known.
11. Toxicological information
Information on likely routes of exposure
Inhalation Prolonged inhalation may be harmful.
Skin contact Causes skin irritation. May cause an allergic skin reaction.
Eye contac
t Causes serious eye damage.
Ingestion Droplets of the product aspirated into the lungs through ingestion or vomiting may cause a serious
chemical pneumonia.
Symptoms related to the
physical, chemical and
toxicological characteristics
Diarrhea. May cause drowsiness and dizziness. Headache. Nausea, vomiting. Irritation of nose
and throat. Aspiration may cause pulmonary edema and pneumonitis. Severe eye irritation.
Symptoms may include stinging, tearing, redness, swelling, and blurred vision. Permanent eye
damage including blindness could result. Skin irritation. May cause redness and pain. May cause
an allergic skin reaction.
Information on toxicological effects
Acute toxicit
y Not expected to be acutely toxic.
Test ResultsComponents Species
Morpholine (CAS 110-91-8)
LD50 Rabbit
Dermal
Acute
500 mg/kg
500 mg/kg, 24 Hours
0.31 - 0.81 ml/kg, 24 Hours
LC50 Rat
Inhalation
8000 ppm, 8 hours
LD50 Guinea pig
Oral
900 mg/kg
Gel Gloss GG-1, GG-8, GG-64, GG-128 SDS US
922736 Version #: 01 Revision date: - Issue date: 15-September-2014
5 / 9
Test ResultsComponents Species
Rat 1050 mg/kg
1.05 g/kg
Oleic acid (CAS 112-80-1)
LD50 Rat
Oral
Acute
74 g/kg
Polyalkyl siloxane (CAS 63148-62-9)
LD50 Rabbit
Dermal
Acute
>= 5000 mg/kg
LD50 Rat
Oral
>= 17000 mg/kg
* Estimates for product may be based on additional component data not shown.
Skin corrosion/irritation Causes skin irritation.
Serious eye damage/eye
irritation
Causes serious eye damage.
Respiratory or skin sensitization
Respiratory sensitizationNot classified.
Skin sensitization May cause an allergic skin reaction.
Germ cell mutagenicity Not classified.
Carcinogenicity Due to the form of the product, exposure to the potentially carcinogenic components is not
expected.
IARC Monographs. Overall Evaluation of Carcinogenicity
D-Limonene (CAS 5989-27-5) 3 Not classifiable as to carcinogenicity to humans.
Morpholine (CAS 110-91-8) 3 Not classifiable as to carcinogenicity to humans.
Quartz (CAS 14808-60-7) 1 Carcinogenic to humans.
NTP Report on Carcinogens
Quartz (CAS 14808-60-7) Known To Be Human Carcinogen.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050)
Not listed.
Reproductive toxicity Not classified.
Specific target organ toxicity –
single exposure
Not classified.
Specific target organ toxicity –
repeated exposure
Not classified.
Aspiration hazard May be fatal if swallowed and enters airways.
Chronic effects May be harmful if absorbed through skin.
12. Ecological information
Ecotoxicity Toxic to aquatic life with long lasting effects.
Persistence and degradabilityNo data is available on the degradability of this product.
Bioaccumulative potential No data available.
Partition coefficient n-octanol / water (log Kow)
Morpholine (CAS 110-91-8) -0.86
Mobility in soil The product is insoluble or slightly soluble in water.
Other adverse effects No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation
potential, endocrine disruption, global warming potential) are expected from this component.
13. Disposal considerations
Disposal instructions Dispose in accordance with all applicable regulations. Must be incinerated in a suitable
incineration plant holding a permit delivered by the competent authorities. This material and its
container must be disposed of as hazardous waste. Do not allow this material to drain into
sewers/water supplies.
Gel Gloss GG-1, GG-8, GG-64, GG-128 SDS US
922736 Version #: 01 Revision date: – Issue date: 15-September-2014
6 / 9
Local disposal regulations Dispose in accordance with all applicable regulations.
Hazardous waste code D001: Waste Flammable material with a flash point <140 F
The waste code should be assigned in discussion between the user, the producer and the waste
disposal company.
Waste from residues / unused
products
Dispose of in accordance with local regulations. Empty containers or liners may retain some
product residues. This material and its container must be disposed of in a safe manner (see:
Disposal instructions).
Contaminated packaging Empty containers should be taken to an approved waste handling site for recycling or disposal.
Since emptied containers may retain product residue, follow label warnings even after container is
emptied.
14. Transport information
DOT
UN1268UN number
Petroleum products, n.o.s. (D-Limonene; C12-C14 isoalkanes)UN proper shipping name
3Class
Transport hazard class(es)
-Subsidiary risk
3Label(s)
IIIPacking group
yesMarine pollutant
Environmental hazards
Read safety instructions, SDS and emergency procedures before handling.Special precautions for user
144, B1, IB3, T4, TP1, TP29Special provisions
150Packaging exceptions
203Packaging non bulk
242Packaging bulk
IATA
UN1268UN number
Petroleum products, n.o.s. (D-Limonene, C12-C14 isoalkanes)UN proper shipping name
3Class
Transport hazard class(es)
-Subsidiary risk
IIIPacking group
yesEnvironmental hazards
3LERG Code
Read safety instructions, SDS and emergency procedures before handling.Special precautions for user
IMDG
UN1268UN number
Petroleum products, n.o.s. (D-Limonene, C12-C14 isoalkanes)UN proper shipping name
3Class
Transport hazard class(es)
-Subsidiary risk
IIIPacking group
yesMarine pollutant
Environmental hazards
F-E, S-EEmS
Read safety instructions, SDS and emergency procedures before handling.Special precautions for user
This substance/mixture is not intended to be transported in bulk.Transport in bulk according to
Annex II of MARPOL 73/78 and
the IBC Code
15. Regulatory information
US federal regulations This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication
Standard, 29 CFR 1910.1200.
One or more components are not listed on TSCA.
TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)
Not regulated.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050)
Not listed.
Gel Gloss GG-1, GG-8, GG-64, GG-128 SDS US
922736 Version #: 01 Revision date: - Issue date: 15-September-2014
7 / 9
CERCLA Hazardous Substance List (40 CFR 302.4)
Morpholine (CAS 110-91-8) LISTED
Superfund Amendments and Reauthorization Act of 1986 (SARA)
Hazard categories Immediate Hazard - Yes
Delayed Hazard - No
Fire Hazard - Yes
Pressure Hazard - No
Reactivity Hazard - No
SARA 302 Extremely hazardous substance
Not listed.
SARA 311/312 Hazardous
chemical
Yes
SARA 313 (TRI reporting)
Not regulated.
Other federal regulations
Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List
Not regulated.
Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)
Not regulated.
Safe Drinking Water Act
(SDWA)
Not regulated.
US state regulations
US. Massachusetts RTK - Substance List
Morpholine (CAS 110-91-8)
Quartz (CAS 14808-60-7)
US. New Jersey Worker and Community Right-to-Know Act
D-Limonene (CAS 5989-27-5)
Morpholine (CAS 110-91-8)
Quartz (CAS 14808-60-7)
US. Pennsylvania Worker and Community Right-to-Know Law
Morpholine (CAS 110-91-8)
Oleic acid (CAS 112-80-1)
Quartz (CAS 14808-60-7)
US. Rhode Island RTK
Not regulated.
US. California Proposition 65
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other
reproductive harm.
US - California Proposition 65 - Carcinogens & Reproductive Toxicity (CRT): Listed substance
Benzene (CAS 71-43-2)
Quartz (CAS 14808-60-7)
International Inventories
Country(s) or region Inventory name On inventory (yes/no)*
Australian Inventory of Chemical Substances (AICS) YesAustralia
Domestic Substances List (DSL) YesCanada
Non-Domestic Substances List (NDSL) NoCanada
Inventory of Existing Chemical Substances in China (IECSC) YesChina
European Inventory of Existing Commercial Chemical
Substances (EINECS)
NoEurope
European List of Notified Chemical Substances (ELINCS) NoEurope
Inventory of Existing and New Chemical Substances (ENCS) NoJapan
Existing Chemicals List (ECL) YesKorea
New Zealand Inventory YesNew Zealand
Philippine Inventory of Chemicals and Chemical Substances
(PICCS)
NoPhilippines
Gel Gloss GG-1, GG-8, GG-64, GG-128 SDS US
922736 Version #: 01 Revision date: - Issue date: 15-September-2014
8 / 9
Country(s) or region Inventory name On inventory (yes/no)*
*A "Yes" indicates this product complies with the inventory requirements administered by the governing country(s).
A "No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing
country(s).
Toxic Substances Control Act (TSCA) Inventory YesUnited States & Puerto Rico
16. Other information, including date of preparation or last revision
Issue date 15-September-2014
Revision date -
Version # 01
NFPA ratings
03
2
List of abbreviations LD50: Lethal Dose, 50%.
LC50: Lethal Concentration, 50%.
EC50: Effective concentration, 50%.
STEL: Short term exposure limit.
TWA: Time weighted average.
DOT: Department of Transportation. ADR: European Agreement concerning the International
Carriage of Dangerous Goods by Road.
IATA: International Air Transport Association.
IMDG: International Maritime Dangerous Goods.
RID: Regulations concerning the International Carriage of Dangerous Goods by Rail.
References RTECS
HSDB - Hazardous Substances Data Bank
GESTIS Substance Database
C&L Inventory database.
Disclaimer This information is provided without warranty. The information is believed to be correct. This
information should be used to make an independent determination of the methods to safeguard
workers and the environment.
Gel Gloss GG-1, GG-8, GG-64, GG-128 SDS US
922736 Version #: 01 Revision date: - Issue date: 15-September-2014
9 / 9
37WA165_SDS.pdf
In case of emergency or spill, contact CHEMTREC at 800-424-9300
MATERIAL SAFETY DATA SHEET
1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND THE
COMPANY/UNDERTAKING
Product Name: M17 – Plastic Cleaner
Use of the Substance/Preparation
Recommended use: Not applicable
Company/Undertaking Identification
2. HAZARDS IDENTIFICATION
Most important hazards: This product contains chemicals listed on Canada WHMIS. See Section 15.
3. COMPOSITION/INFORMATION ON INGREDIENTS
Hazardous Ingredients
Components CAS # % Weight OSHA PEL
TWA
EINECS No. Classification
Light Distillate 64742-14-9 15-20 None — —
Hydrotreated Distillate 64742-46-7 5-10 None 265-148-2 265-148-2
Natural Diatomaceous Earth 61790-53-2 4-8 10mg/m
3
— —
Glycerine 56-81-5 2-5 10mg/m
3
200-289-5 —
4. FIRST AID MEASURES
General Advice: In the case of accident or if you feel unwell, seek medical advice immediately (show
the label where possible).
Inhalation: Avoid breathing vapors or mists. Move to fresh air. Consult a physician.
Skin contact: Wash off immediately with soap and plenty of water. If skin irritation persists, call a
physician.
Page 1/5
Meguiar’s USA
17991 Mitchell South
Irvine, CA 92614
Tel: 949-752-8000
Fax: 949-752-5784
Print date: 07/26/2010
Reference Number:
None Prepared Date: 07/26/2010
Meguiar’s Holland
Laan der Verenigde Naties 40
33174 DA Dordrecht
Holland
Tel: 31-78-6210268 Meguiar’s Hong Kong
Suite 6-7, 20/F Marina House
68 Hing Man Street
Shaukeiwan
Hong Kong
Tel: 852-2967-0202
Meguiar’s France 3 rud de Verdun – B t. D 78590 Noisy Le Roi France Tel: 33-1-30-80-02-16
Meguiar’s UK Ltd.
3 Lamport Court
Heartlands
Daventry NN11 8UF
Tel: 0870 241 6696
Fax: 01327 300 116
Eye contact: Rinse thoroughly with plenty of water for at least 15 minutes and consult a physician.
Ingestion: Rinse mouth. Drink 1 or 2 glasses of water. Consult a physician if necessary. Do not
induce vomiting without medical advice. If a person vomits when lying on his back,
place him in the recovery position.
5. FIRE-FIGHTING MEASURES
NFPA:
Suitable extinguishing media: Use dry chemical, CO2, water spray or alcohol-resistant foam.
Specific hazards: Not applicable
Special protective equipment for firefighters: In the event of fire, wear self-contained breathing apparatus.
Extinguishing media which must not be used for safety reasons: Not applicable
Specific methods: Not applicable
6. ACCIDENTAL RELEASE MEASURES
Personal precautions: Ensure adequate ventilation. Avoid contact with skin and eyes
Environmental precautions: Local authorities should be advised if significant spillages cannot be contained. Do
not contaminate surface water. Prevent further leakage or spillage.
Methods for cleaning up: Package all material in plastic, cardboard or metal containers for disposal in
compliance with the environment protection (duty of care) regulations 1991.
7. HANDLING AND STORAGE
Handling:
Technical measures/precautions:
Use only in area well ventilated area
Safe handling advice:
None under normal processing
Storage:
Store at room temperature in the original container. Do not freeze.
Incompatible products:
No materials to be specially mentioned
Page 2/5
Flammability: 0Health: 1 Reactivity: 0
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Engineering measures to reduce
exposure:
Ensure adequate ventilation..
Respiratory protection: No personal respiratory protective equipment normally required.
Skin and body protection: Not applicable.
Eye protection: Avoid contact with eyes. If splashes are likely to occur, wear:. Goggles.
Hand protection: Preventative skin protection: Neoprene gloves recommended.
9. PHYSICAL AND CHEMICAL PROPERTIES9. PHYSICAL AND CHEMICAL PROPERTIES9. PHYSICAL AND CHEMICAL PROPERTIES9. PHYSICAL AND CHEMICAL PROPERTIES
General Information
Important Health Safety and Environmental Information
pH @70 F: 5.50
Flash point: 200 ( F), 93 ( C ) Method: PMCC-ASTM D93-90
Boiling point/range: 390 ( F), 199 ( C)
Water Solubility: Not determined
Vapor density: >1
Specific gravity: 1.00
Evaporation rate: <1
VOC content: 17% max.
10. STABILITY AND REACTIVITY
Stability: Stable under recommended storage conditions.
Polymerization: None under normal processing.
Conditions to avoid: Extremes of temperature and direct sunlight
Materials to avoid: Strong acids and strong bases, Strong oxidizing agents
Hazardous decomposition products: None reasonably foreseeable
11. TOXICOLOGICAL INFORMATION
Component Information
Additional Information: The product is not subject to classification according to the calculation method of the
General EC Classification Guidelines for Preparations as issued in the latest version.
When used and handled according to specifications, the product does not have any
harmful effects according to our experience and the information provided to us.
12. ECOLOGICAL INFORMATION
Ecotoxicity
Page 3/5
Not applicable
Color: Yellow Green
Appearance:
Odor: Sweet
Physical state: Liquid
Product Information
Aquatic toxicity: No information available
Component Information
Ecotoxicity effects: Not determined
13. DISPOSAL CONSIDERATIONS
Waste from residues / unused products:
In accordance with local and national regulations.
Contaminated packaging:
Disposal must be made according to local and federal regulations.
Ewc waste disposal no:
Not applicable
Further information
According to the European Waste Catalogue, Waste Codes are not product specific, but application specific
14. TRANSPORT INFORMATION
General Transportation Statement This product does not require classification by DOT, IATA,
ICAO or IMDG.
Other information:
The description shown may not apply to all shipping situations. Consult 49CFR, or appropriate Dangerous Goods
Regulations, for additional description requirements and mode-specific or quantity-specific shipping requirements.
15. REGULATORY INFORMATION
Components TSCA DSL/NDSL Canada - WHMIS Classification
Hydrotreated Distillate 64742-46-7 Present Present
Natural Diatomaceous Earth 61790-53-2 Present Present D2B
Glycerine 56-81-5 Present Present D2B
CERCLA/SARA 313 Emission reporting
None
16. OTHER INFORMATION
Prepared by: Health & Safety
Literary reference: None
Page 4/5
Disclaimer: To the best of our knowledge, the information contained herein is accurate. However,
neither the above named supplier nor any of its subsidiaries assumes any liability
whatsoever for the accuracy or completeness of the information contained herein.
Final determination of suitability of any material is the sole responsibility of the user.
All materials may present unknown hazards and should be used with caution.
Although certain hazards are described herein, we cannot guarantee that these are
the only hazards that exist
End of Safety Data Sheet
Page 5/5
37WA164_SDS.pdf
In case of emergency or spill, contact CHEMTREC at 800-424-9300
MATERIAL SAFETY DATA SHEET
1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND THE
COMPANY/UNDERTAKING
Product Name: M04 – Heavy-Cut Cleaner
Use of the Substance/Preparation
Recommended use: All-purpose cleaner.
Company/Undertaking Identification
2. COMPOSITION/INFORMATION ON INGREDIENTS
Hazardous Ingredients
Components CAS # % Weight OSHA PEL
TWA
EINECS No. Classification
Dialuminum Trioxide 1344-28-1 10-20 = 15 mg/m
TWA (total
dust)
= 5 mg/m
TWA
(respirable
fraction)
215-691-6 —
Light Distillate 64742-14-9 10-20 None — —
Hydrotreated Distillate 64742-46-7 1-5 None — R65
3. HAZARDS IDENTIFICATION
Most important hazards: This product contains chemicals listed on Canada WHMIS. See Section 15.
4. FIRST AID MEASURES
Page 1/5
Prepared Date: 07/17/2007
Meguiar’s Holland
Laan der Verenigde Naties 40
33174 DA Dordrecht
Holland
Tel: 31-78-6210268 Meguiar’s Hong Kong
Suite 6-7, 20/F Marina House
68 Hing Man Street
Shaukeiwan
Hong Kong
Tel: 852-2967-0202
Meguiar’s France 3 rud de Verdun – B t. D 78590 Noisy Le Roi France Tel: 33-1-30-80-02-16
Meguiar’s UK Ltd.
3 Lamport Court
Heartlands
Daventry NN11 8UF
Tel: 0870 241 6696
Fax: 01327 300 116
Meguiar’s USA
17991 Mitchell South
Irvine, CA 92614
Tel: 949-752-8000
Fax: 949-752-5784
Print date: 07/17/2007
Reference Number: 11-83B
General Advice: In the case of accident or if you feel unwell, seek medical advice immediately (show
the label where possible).
Inhalation: Prolonged or intentional exposure to high concentrations may cause respiratory track
irritation. Move to fresh air. If symptoms persist, call a physician.
Skin contact: Wash off immediately with soap and plenty of water. If skin irritation persists, call a
physician.
Eye contact: Flush eye(s) immediately with plenty of water. If symptoms persist, call a physician
Ingestion: Rinse mouth. Drink 1 or 2 glasses of water. Consult a physician if necessary.
5. FIRE-FIGHTING MEASURES
NFPA:
Suitable extinguishing media: Use dry chemical, CO2, water spray or alcohol-resistant foam.
Specific hazards: Not applicable
Special protective equipment for firefighters: As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH (approved or equivalent) and full protective gear.
Extinguishing media which must not be used for safety reasons: Not applicable
Specific methods: Not applicable
6. ACCIDENTAL RELEASE MEASURES
Personal precautions: Ensure adequate ventilation. Avoid contact with skin and eyes
Environmental precautions: Do not contaminate surface water.
Methods for cleaning up: Wipe up with absorbent material (e.g. cloth, fleece).
7. HANDLING AND STORAGE
Handling:
Technical measures/precautions:
Use only in area well ventilated area
Safe handling advice:
None under normal processing
Storage:
Store at room temperature in the original container. Keep away from direct sunlight. Do not freeze.
Incompatible products:
Do not store together with acids or oxidizers.
Page 2/5
Flammability: 1Health: 1 Reactivity: 0
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Engineering measures to reduce
exposure:
Ensure adequate ventilation..
Respiratory protection: No personal respiratory protective equipment normally required.
Skin and body protection: No special precautions required..
Eye protection: Avoid contact with eyes. If splashes are likely to occur, wear:. Goggles.
Hand protection: Preventative skin protection:. Neoprene Gloves..
9. PHYSICAL AND CHEMICAL PROPERTIES
General Information
Important Health Safety and Environmental Information
pH @70 F: N/A
Flash point: >200 ( F), 93 ( C ) Method: PMCC-ASTM D93-90
Boiling point/range: 390 ( F), 199 ( C)
Water Solubility: Moderately soluble Negligible
Vapor density: >1
Evaporation rate: <1
VOC content: 17% max.
Specific gravity: 1.10
10. STABILITY AND REACTIVITY
Stability: Stable under recommended storage conditions.
Polymerization: None under normal processing.
Conditions to avoid: Extremes of temperature and direct sunlight
Materials to avoid: Strong acids and strong bases, Strong oxidizing agents,
Strong alkalis
Hazardous decomposition products: Not determined, None under normal use
11. TOXICOLOGICAL INFORMATION
Component Information
Additional Information: The product is not subject to classification according to the calculation method of the
General EC Classification Guidelines for Preparations as issued in the latest version.
When used and handled according to specifications, the product does not have any
harmful effects according to our experience and the information provided to us.
12. ECOLOGICAL INFORMATION
Page 3/5
Physical state: Liquid
Liquid
Color: White
Appearance:
Odor: Sweet
Ecotoxicity
Product Information
Aquatic toxicity: No information available
Component Information
Ecotoxicity effects: Not determined
13. DISPOSAL CONSIDERATIONS
Waste from residues / unused products:
Waste disposal must be in accordance with appropriate Federal, State, and local regulations. This product, if unaltered by
use, may be disposed of by treatment at a permitted facility or as advised by your local hazardous waste regulatory
authority.
Contaminated packaging:
Disposal must be made according to local and federal regulations.
Ewc waste disposal no:
Not applicable
Further information
According to the European Waste Catalogue, Waste Codes are not product specific, but application specific
14. TRANSPORT INFORMATION
General Transportation Statement This product does not require classification by DOT, IATA,
ICAO or IMDG.
Other information:
The description shown may not apply to all shipping situations. Consult 49CFR, or appropriate Dangerous Goods
Regulations, for additional description requirements and mode-specific or quantity-specific shipping requirements.
15. REGULATORY INFORMATION
Components TSCA DSL/NDSL Canada - WHMIS Classification
Dialuminum Trioxide 1344-28-1 XU Present F; B6
Hydrotreated Distillate 64742-46-7 Present Present
CERCLA/SARA 313 Emission reporting
None
16. OTHER INFORMATION
Prepared by: Health & Safety
Literary reference: None
Page 4/5
Disclaimer: To the best of our knowledge, the information contained herein is accurate. However,
neither the above named supplier nor any of its subsidiaries assumes any liability
whatsoever for the accuracy or completeness of the information contained herein.
Final determination of suitability of any material is the sole responsibility of the user.
All materials may present unknown hazards and should be used with caution.
Although certain hazards are described herein, we cannot guarantee that these are
the only hazards that exist
End of Safety Data Sheet
Page 5/5
37WA160_SDS.pdf
In case of emergency or spill, contact CHEMTREC at 800-424-9300
MATERIAL SAFETY DATA SHEET
1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND THE
COMPANY/UNDERTAKING
Product Name: M10 – Plastic Polish
Use of the Substance/Preparation
Recommended use: Polishing agent/Burnishing compound
Company/Undertaking Identification
2. HAZARDS IDENTIFICATION
Most important hazards: This product contains chemicals listed on Canada WHMIS. See Section 15.
3. COMPOSITION/INFORMATION ON INGREDIENTS
Hazardous Ingredients
Components CAS # % Weight OSHA PEL
TWA
EINECS No. Classification
Hydrotreated Distillate 64742-46-7 15-20 None — —
Light Distillate 64742-14-9 10-15 None — —
Glycerine 56-81-5 1-5 10mg/m
3
200-289-5 —
4. FIRST AID MEASURES
General Advice: In the case of accident or if you feel unwell, seek medical advice immediately (show
the label where possible).
Inhalation: Prolonged or intentional exposure to high concentrations may cause respiratory track
irritation. Move to fresh air. If symptoms persist, call a physician.
Skin contact: Thoroughly wash exposed area with water. If skin irritation persists, call a physician.
Eye contact: Flush eyes with water as a precaution. If symptoms persist, call a physician
Page 1/5
Meguiar’s UK Ltd.
3 Lamport Court
Heartlands
Daventry NN11 8UF
Tel: 0870 241 6696
Fax: 01327 300 116
Meguiar’s USA
17991 Mitchell South
Irvine, CA 92614
Tel: 949-752-8000
Fax: 949-752-5784
Print date: 07/13/2009
Reference Number:
17-39A Prepared Date: 07/13/2009
Meguiar’s Holland
Laan der Verenigde Naties 40
33174 DA Dordrecht
Holland
Tel: 31-78-6210268 Meguiar’s Hong Kong
Suite 6-7, 20/F Marina House
68 Hing Man Street
Shaukeiwan
Hong Kong
Tel: 852-2967-0202
Meguiar’s France 3 rud de Verdun – B t. D 78590 Noisy Le Roi France Tel: 33-1-30-80-02-16
Ingestion: Drink 1 or 2 glasses of water. Do not induce vomiting. Consult a physician if
necessary.
5. FIRE-FIGHTING MEASURES
NFPA:
Suitable extinguishing media: Use dry chemical, CO2, water spray or alcohol-resistant foam
Specific hazards: Not applicable
Special protective equipment for firefighters: As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH (approved or equivalent) and full protective gear.
Extinguishing media which must not be used for safety reasons: Not applicable
Specific methods: Not applicable
6. ACCIDENTAL RELEASE MEASURES
Personal precautions: Ensure adequate ventilation.
Environmental precautions: Do not allow material to contaminate ground water system.
Methods for cleaning up: Wipe up with absorbent material (e.g. cloth, fleece).
7. HANDLING AND STORAGE
Handling:
Technical measures/precautions:
Not applicable
Use only in area well ventilated area
Safe handling advice:
None under normal processing
Storage: Store at room temperature in the original container. Keep away from direct sunlight. Do not freeze.
Incompatible products:
Do not store together with acids or oxidizers.
Page 2/5
Flammability: 0Health: 1 Reactivity: 0
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Engineering measures to reduce
exposure:
Ensure adequate ventilation..
Respiratory protection: No personal respiratory protective equipment normally required.
Skin and body protection: No special precautions required.
Eye protection: Avoid contact with eyes. If splashes are likely to occur, wear:. Goggles.
Hand protection: Preventative skin protection: Rubber gloves
9. PHYSICAL AND CHEMICAL PROPERTIES
General Information
Important Health Safety and Environmental Information
pH @70 F: 6.50
Flash point: 200 ( F), 93 ( C )
Boiling point/range: 212 ( F), 100 ( C)
Water Solubility: Moderately soluble
Vapor density: >1
Specific gravity: 0.96
Evaporation rate: <1
VOC content: 11%
10. STABILITY AND REACTIVITY
Stability: Stable under recommended storage conditions.
Polymerization: None under normal processing.
Conditions to avoid: Extremes of temperature and direct sunlight
Materials to avoid: Strong acids and oxidizing agents
Hazardous decomposition products: None under normal use
11. TOXICOLOGICAL INFORMATION
Component Information
Additional Information: The product is not subject to classification according to the calculation method of the
General EC Classification Guidelines for Preparations as issued in the latest version.
When used and handled according to specifications, the product does not have any
harmful effects according to our experience and the information provided to us.
12. ECOLOGICAL INFORMATION
Ecotoxicity
Page 3/5
Liquid
Color: White
Appearance:
Odor: Sweet
Physical state: Liquid
Product Information
Aquatic toxicity: No information available
Component Information
Ecotoxicity effects: This product has no known eco-toxicological effects.
13. DISPOSAL CONSIDERATIONS
Waste from residues / unused products:
Waste disposal must be in accordance with appropriate Federal, State, and local regulations. This product, if unaltered by
use, may be disposed of by treatment at a permitted facility or as advised by your local hazardous waste regulatory
authority.
Contaminated packaging:
Disposal must be made according to local and federal regulations.
Ewc waste disposal no:
Not applicable
Further information
According to the European Waste Catalogue, Waste Codes are not product specific, but application specific
14. TRANSPORT INFORMATION
General Transportation Statement This product does not require classification by DOT, IATA,
ICAO or IMDG.
Other information:
The description shown may not apply to all shipping situations. Consult 49CFR, or appropriate Dangerous Goods
Regulations, for additional description requirements and mode-specific or quantity-specific shipping requirements.
15. REGULATORY INFORMATION
Components TSCA DSL/NDSL Canada - WHMIS Classification
Hydrotreated Distillate 64742-46-7 Present Present
Glycerine 56-81-5 Present Present D2B
CERCLA/SARA 313 Emission reporting
None
16. OTHER INFORMATION
Prepared by: Health & Safety
Literary reference: None
Page 4/5
Disclaimer: To the best of our knowledge, the information contained herein is accurate. However,
neither the above named supplier nor any of its subsidiaries assumes any liability
whatsoever for the accuracy or completeness of the information contained herein.
Final determination of suitability of any material is the sole responsibility of the user.
All materials may present unknown hazards and should be used with caution.
Although certain hazards are described herein, we cannot guarantee that these are
the only hazards that exist
End of Safety Data Sheet
Page 5/5
37WA149_SDS.pdf
MATERIAL SAFETY DATA SHEET
FORMULA FIVE
Mold Cleaner
MSDS Number: F5C-001 Effective Date: 01 March 2007 Page 1 of 6
SECTION
1: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME FORMULA FIVE
Mold Cleaner
GENERIC NAME Mold Cleaner
MANUFACTURER REXCO
P.O. Box 80996
Conyers, Georgia 30013
USA
TRANSPORTATION EMERGENCY :
CHEMTREC (800) 424-9300 U.S.A. (24 hours/day)
CHEMTREC (703) 527-3887 International (Collect calls accepted)
CUSTOMER SERVICE AND PRODUCT EMERGENCY :
REXCO (800) 888-1060 U.S.A and Canada
REXCO (770) 483-7610 International
SECTION 2: COMPOSITION / INFORMATION ON INGREDIENTS
COMPONENT CAS NUMBER CONCENTRATION (%)
Toluene* 108-88-3 28 – 32%
Xylene* 1330-20-7 28 – 32%
Ethyl Methyl Ketone* 78-93-3 37 – 43%
*This chemical is subject to the reporting requirements of section 313 of SARA Title III.
SECTION
3: HAZARDS IDENTIFICATION
NFPA RATING: Health 2, Fire 3, Reactivity 1
HMIS RATING: Health 2, Fire 3, Reactivity 1
0=
MINIMAL, 1=SLIGHT, 2=MODERATE, 3=HIGH, 4=EXTREME
POTENTIAL HEALTH EFFECTS
EYES Irritating to eyes, ranging from temporary irritation, transient corneal injury and pain to
possible permanent injury or blindness.
SKIN Irritating to skin. Prolonged or repeated exposure may result in de-fatting, skin dermatitis,
reddening, blisters or temporary loss of feeling depending on exposure.
INHALATION Harmful. Danger of serious damage to health by prolonged inhalation. Vapors may cause
nausea, vomiting, gastrointestinal bleeding, abdominal pain, and central nervous system
depression with symptoms ranging from drunkenness to unconsciousness, narcosis, coma,
cyanosis, respiratory failure, and death, depending on the quantity ingested.
MATERIAL SAFETY DATA SHEET
FORMULA FIVE
Mold Cleaner
MSDS Number: F5C-001 Effective Date: 01 March 2007 Page 2 of 6
INGESTION Harmful. May cause lung damage if swallowed. May cause nausea, vomiting, gastrointestinal
bleeding, abdominal pain, and central nervous system depression with symptoms ranging
from drunkenness to unconsciousness, narcosis, coma, respiratory failure, mild to severe
pulmonary injury, and death, depending on the quantity ingested.
CHRONIC HEALTH EFFECTS : May result in harm to unborn child.
SYMPTOMS OF EXPOSURE : Symptoms of exposure through inhalation, ingestion, or direct contact with skin
may include nausea, vomiting, diarrhea, irritation of nose, throat, airways, or skin, central nervous system
depression possibly including headache, loss of coordination, drowsiness, fatigue, and unconsciousness
and death in extreme cases. Pre-existing eye, skin, or respiratory disorders may be aggravated by exposure
to this product.
PRIMARY ROUTES OF ENTRY : Skin contact, skin absorption, eye contact, and inhalation
CANCER INFORMATION : Neither this product nor any of its components is listed as a carcinogen or partial
carcinogen by the following agencies: the National Toxicology Program, the International Agency for
Research on Cancer, and the Occupational Safety and Health Administration.
SECTION 4: FIRST AID MEASURES
EYES Flush immediately with cold water for 15 minutes and seek medical attention.
SKIN Remove contaminated clothing and wash affected area with soap and water. If irritation from
contact persists, seek medical attention. Launder contaminated clothing including shoes
prior to reuse.
INHALATON If light-headed or having difficulty breathing, expose individual to fresh air and/or oxygen. If
breathing stops, begin artificial respiration and seek immediate medical attention.
INGESTION Seek immediate medical attention. Only induce vomiting if directed to do so by medical
personnel. If vomiting occurs spontaneously, keep victim s head below hips to prevent
aspiration into lungs. If possible, do not leave victim unattended.
SECTION 5: FIRE FIGHTING MEASURES
FLASH POINT / METHOD: <73 F (23 C) / Tagliabue Closed Cup method (TCC)
AUTO IGNITION TEMPERATURE : Not Applicable
FLAMMABLE LIMITS IN AIR (% BY VOLUME): LEL Lower 1.2% / UEL Upper 7%
FIRE AND EXPLOSION HAZARDS : Flammable. Low flash point. Keep work areas free of hot metal surfaces
and other sources of ignition.
EXTINGUISHING MEDIA: Use dry chemicals, CO2, water fog, or foam.
FIRE FIGHTING INSTRUCTIONS: Wear a NIOSH-approved self contained breathing apparatus in positive
pressure mode and full bunker gear. Water may be unsuitable as an extinguishing media but helpful in
keeping adjacent containers cool in order to prevent container rupture. Avoid spreading burning liquid with
water used for cooling purposes.
MATERIAL SAFETY DATA SHEET
FORMULA FIVE
Mold Cleaner
MSDS Number: F5C-001 Effective Date: 01 March 2007 Page 3 of 6
SECTION 6: ACCIDENTAL RELEASE MEASURES
IN CASE OF SPILL: Keep sources of ignition and hot metal surfaces isolated from spill. Persons involved in
clean-up should wear personal protection equipment. Stop spill at source and prevent from spreading. Flush
spilled material into suitable retaining areas or containers. Small amounts of spilled material may be absorbed
with any standard absorbent. If run-off occurs, notify proper authorities as required. Place in chemical waste
container and dispose of in accordance with local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
Store in a dry location at 60 - 80 F (15 - 27 C) and away from open flames, heat, and sparks. Do not store at
temperatures above 110 F (43 C) to avoid vapor pressure in closed containers. Store only in areas
approved for Flammable Liquid. Keep work areas free of hot metal surfaces and other sources of ignition.
Keep container tightly closed when not in use.
Repacking not recommended. Repack only into high-density polyethylene (HDPE) or steel containers. Do not
repack in aluminum containers. Containers used for repackaging should be thoroughly tested for long-term
product compatibility before use. Ground all equipment before pumping the product. Protect from static
electrical sparks or other ignition sources. All new containers must exhibit product labels required for proper
identification, safety, handling, and storage. Store away from strong oxidizers. Empty containers may contain
product residue such as vapors continue to observe proper handling and storage precautions.
SECTION 8: EXPOSURE CONTROLS / PERSONAL PROTECTION
EYE PROTECTION: Safety glasses with side shields, chemical goggles, or face shield are advised. Eye
washes are recommended for work areas.
SKIN PROTECTON: Wear impervious gloves (neoprene, rubber, NBR nitrile), clothing, and shoes to prevent
skin contact. Safety showers are recommended for work areas. Remove contaminated clothing and wash in
hot water and soap prior to reuse.
RESPIRATORY PROTECTION : Exposure levels should be kept below the PEL or TLV for this product. Local
exhaust preferred. If exposure exceeds recommended levels, use of NIOSH-approved cartridge respirator or
gas mask is advised. Engineering controls should be implemented if necessary to reduce exposure.
ENGINEERING CONTROLS : Provide sufficient general and/or local exhaust (explosion-proof ventilation) to
keep exposure below PEL or TLV.
EXPOSURE GUIDELINES
COMPONENT OSHA TWA ACGIH TLV
Toluene 200 ppm PEL/TWA 50 ppm TLV/TWA
Xylene 100 ppm PEL/TWA 100 ppm TLV/TWA
Ethyl Methyl Ketone 200 ppm PEL/TWA 200 ppm TLV/TWA
PEL = PERMISSIBLE EXPOSURE LIMITS TLV = THRESHOLD LIMIT VALUE TWA = TIME WEIGHTED AVERAGE (8 HOURS)
MATERIAL SAFETY DATA SHEET
FORMULA FIVE
Mold Cleaner
MSDS Number: F5C-001 Effective Date: 01 March 2007 Page 4 of 6
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE: Clear Liquid SPECIFIC GRAVITY (H2O=1): 0.84
ODOR: Mild Solvent EVAPORATION RATE (BUTYL ACETATE= 1) : <1
BOILING POINT: 176 286 F (80 141 C) VAPOR DENSITY (AIR= 1) : > AIR
MELTING POINT: Not Applicable SOLUBILITY IN WATER: Insoluble
V.O.C. 0.826 g/cm
3
REACTIVITY IN WATER: No
V.O.C. = VOLATILE ORGANIC CONTENT
SECTION 10: STABILITY AND REACTIVITY
STABILITY: Stable
CONDITIONS TO AVOID: Open flames, hot surfaces, or any ignition source.
INCOMPATIBILITY: Incompatible with strong oxidizing agents, strong acids or bases, alkali metals, halogens,
and strong alkalis.
HAZARDOUS DECOMPOSITION : Thermal decomposition in the presence of air may yield carbon monoxide
and/or carbon dioxide, toxic gases. Smoke and vapor.
HAZARDOUS POLYMERIZATION : Will not occur
SECTION 11: TOXICOLOGICAL INFORMATION
EYES: May cause mild and temporary irritation of eyes and mucous membranes to permanent injury
or blindness.
SKIN: May cause irritation to skin through drying and de-fatting. May cause reddening, dermatitis,
skin cracking, eczema, blisters or temporary loss of feeling.
INHALATION: Vapor at low concentrations may cause mild irritation of respiratory system or lungs. At high
concentrations and exposure may cause nausea, vomiting, headaches, unconsciousness,
cyanosis or death.
INGESTION: May cause irritation of mucous membranes or abdominal pain. Severe exposure may cause
pulmonary injury possibly death.
SECTION 12: ECOLOGICAL INFORMATION
Not soluble in water.
MATERIAL SAFETY DATA SHEET
FORMULA FIVE
Mold Cleaner
MSDS Number: F5C-001 Effective Date: 01 March 2007 Page 5 of 6
SECTION 13: DISPOSAL CONSIDERATIONS
Waste material may be incinerated at an approved facility where permitted under appropriate Federal, State,
and Local regulations.
SECTION 14: TRANSPORT INFORMATION
DOT CLASSIFICATION: Flammable Liquid, n.o.s. (Methyl Ethyl Ketone, Toluene); 3; UN1993;
Packing Group II
ICAO / IATA CLASSIFICATION: UN1993; Flammable Liquid, n.o.s. (Methyl Ethyl Ketone, Toluene); 3;
Packing Group II
IMDG CLASSIFICATION: UN1993; Flammable Liquid, n.o.s. (Methyl Ethyl Ketone, Toluene); 3;
Packing Group II
SECTION 15: REGULATORY INFORMATION
COMPREHENSIVE ENVIRONMENTAL RESPONSE COMPENSATION AND LIABILITY ACT OF 1980 (CERCLA)
COMPONENT
REPORTABLE QUANTITY (RQ)
Toluene 1000 lbs Xylene 1000 lbs
Ethyl Methyl Ketone 5000 lbs
SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT OF 1986 (SARA) TITLE III
SARA 302
: Extremely Hazardous Substance: NO
SARA 311: Hazardous Chemical: YES
HAZARD CATEGORIES: FIRE YES
REACTIVITY NO
SUDDEN RELEASE OF PRESSURE NO
IMMEDIATE RELEASE OF PRESSURE YES
DELAYED RELEASE OF PRESSURE YES
OCCUPATIONAL HEALTH AND SAFETY ADMINISTRATION (OSHA) CLASSIFICATION: 29 CFR 1910.1200
Hazardous Chemical: YES
CALIFORNIA PROPOSITION 65: WARNING -This product contains a chemical(s) known to the state of
California to cause birth defects or other reproductive harm.
WORKPLACE HAZARDOUS MATERIAL INFORMATION SYSTEM (WHMIS) CLASSIFICATION:
Hazardous: Flammable Liquid
MATERIAL SAFETY DATA SHEET
FORMULA FIVE
Mold Cleaner
MSDS Number: F5C-001 Effective Date: 01 March 2007 Page 6 of 6
CHEMICAL INVENTORY: Components are either listed on the following chemical inventories or qualify for an
exemption:
UNITED STATES Toxic Substances Control Act (TSCA)
CANADA Canadian Domestic Substance List (DSL)
EUROPE European Inventory of Existing Commer cial Chemical Substances (EINECS)
AUSTRALIA Australian Inventory of Chemical Substances (AICS)
JAPAN Existing and New Chemical Substances (MITI)
S. KOREA Existing Chemicals List (KECL)
SECTION 16: OTHER INFORMATION
All information provided in this Material Safety Data Sheet is believed to be accurate and reliable of typical
values and not as a product specification. REXCO makes no warranty of any kind, express or implied,
including warranties of merchantability or fitness for a particular purpose, concerning the safe use of this
material in your process or in combination with other substances. Users should make their own tests and
assessments as to the suitability of this product or the information contained herein for their particular
purposes and uses and compliance with all applicable laws and regulations.
Prepared by: REXCO Product Stewardship Department
37WA150_SDS.pdf
Safety Data Sheet
PARTALL Hi-Temp Wax
Safety Data Sheet
according to OSHA HCS and GHS – Canada WHMIS 2015
1,1 Product ldentifier
Product form
Trade name
Telephone
Fax
Email
Website
1.4 Emergency telephone number
Chemtrec (24 hours/day)
Precautionary statements
P101
PLO2
P103
P301 + P31-0
P331
Mixture
PARTALL Hi-Temp Wax
t-770-483-76t0
1-770-483-8550
info@ rexco-usa.com
www,rexco-usa,com
1-800-434-9300 (USA and Canada)
I-7 03-527 -3887
{international; collect calls accepted)
PARTALL Hi-Temp Wax
Version: 5.0
Revisiondate: 2021-01-01
Print date: 2O2l-O2-03
SECTION 1, IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKING
1,2 Relevant identified uses of the substance or mixture and uses advised against
Relevant identified uses : Release agent
1.3 Details of the supplier of the safety data sheet
Supplier REXCO
P.O. Box 80996
Conyers, GA 30013
U.S.A.
SECTION 2. Hazards ldentification
2.1 Classification of the substance or mixture
Classification according to OSHA-HCS and GHS-Canada WHMIS 2015
Asp. Tox. 1 H304 May be fatal if swallowed and enters airways
See section 16 for full text of H-phrases.
2.2 Label elements
Labeling according to the Globally Harmonized System (GHS)
Pictograms
Signal word Danger
Hazard statements
H304 May be fatal if swallowed and enters airways
lf medical advice is needed, have product container or label at hand.
Keep out of reach of children.
Read label before use.
lF SWALLOWED: lmmediately call a POISON CENTER/doctor.
Do NOT induce vomiting.
Revision date: Llt/2O2L Version: 5.0 r/7
Safety Data Sheet PARTALL Hi-Temp Wax
Store locked up.
Dispose of contents/container in accordance with local/regional/national/international regulations.
P405
P501
2.3 Other hazards
Material does not meet the criteria for PBT or vPvB in accordance with REACH Annex Xlll
SECTION 3. Composition/information on ingredients
3.1 Substances
Not applicable. This material is not defined as a substance.
3.2 Mixtures
This material is defined as a mixture.
Components contributing to the classification of this material
Distillates (petroleum), hydrotreated light
CAS No. 64742-47-8
Asp. Tox. 1, H304
6555
Componentsnotlistedareeithernon-hazardousorarebelowreportablelimits. Concentrationsareinpercentbyweight.
SECTION 4. First aid measures
General information
Do not leave victim unattended. Show this safety data sheet to doctor in attendance.
4.1 Description of first aid measures
lnhalation
provide fresh air if light-headed or having difficulty breathing. Provide artificial respiration if needed. lf difficulty breathing persists, seek medical attention.
lf unconscious, place victim on their side for transport to medical facility.
Skin
Remove contaminated clothing and wash affected area with soap and warm water. lf irritation persists, seek medical attention. Launder contaminated
clothing and shoes prior to reuse.
Eyes
Flush immediately with cold water for l-5 minutes. Remove contact lenses. Keep eye wide open while rinsing. Get prompt medical attention’
lngestion
Seek immediate medical attention. Do not induce vomiting. lf spontaneous vomiting occurs keep victim’s head below hips to prevent aspiration into lungs’
Do not leave individual unattended.
4,2 Most important symptoms and effects, both acute and delayed
Can cause eye irritation. May cause skin irritation. lf swallowed, can cause nausea and vomiting with danger of Chemical Pneumonia. Prolonged or repeated
exposure may result in conjunctiva, skin dermatitis, and central nervous system depression, including headache, dizziness, loss of coordination, and
u nconsciousness.
4.3 lndication of any immediate medical attention and special treatment
Treat symptomatically. Seek immediate medical attention if ingested.
SECTION 5. Firefighting measures
5.1 Extinguishing media
Suitable extinguishing media
Standard procedure for chemical fires. Use dry chemicals or foam. Use extinguishing measures that are appropriate to local circumstances and the
surrounding environment.
Revision dalei lh/2O2I Version: 5.0 2/7
Safety Data Sheet PARTALL Hi-Temp Wax
Unsuitable extinguishing media
Donotusehighvolumewaterjet. Avoidspreadingburningliquidwithwaterusedforcoolingpurposes
5.2 Special hazards arising from the substance or mixture
None inherent to this product.
Hazardous decomposition products formed during combusion
Carbon oxides, fluorinated compounds
5.3 Advice for firefighters
Evacuate area. Firefighters should use standard protective equipment and should use self-contained breathing apparatus in enclosed spaces’ Use water
spray to cool surfaces exposed to fire and to protect personnel.
SECTION 6. Accidental release measures
6.1 Personal precautions, protective equipment and emergency procedures
Use personal protective equipment. Ensure adequate ventilation. Keep sources of ignition and hot metal surfaces isolated from spill
6,2 Environmental precautions
prevent product from entering drains, waterways, sewers, and soil. Stop spill at source and prevent further leakage or spillage if safe to do so. Notify proper
authorities if product enters sewers or public waters.
6.3 Methods and material for containment and cleaning up
Confine spill and place into suitable, closed container for disposal. Dispose of in accordance with regional, national, and local laws and regulations’
5.4 Reference to other sections
Section 7: safe handling. Section 8: personal and protective equipment. Section 10: incompatible materials. Section 13: disposal information. Section 16: full
text of abbreviations.
SECTIoN 7. Handling and storage
7.1 Precautions for safe handling
Use in a well ventilated area or use appropriate respirator when ventilation is inadequate. Do not breathe vapor. Wear personal protective clothing and
equipment as indicated in Section 8. Eliminate all sources of ignition. Do not ingest. Use good industrial hygiene practices in handlingthis material. Do not
smoke, eat or drink while using this product. Avoid contamination of tobacco products when handling this material. lnhalation of vapors in the presence of
tobacco products can result in polymer fume fever. Wash hands and other exposed areas with mild soap and water before eating, drinking or smoking and
leaving work. Clean up spills as soon as they occur. Empty containers may contain residual amounts of this product and should be handled with care’ Do not
reuse containers.
7,2 Conditions for safe storage, including any incompatibilities
Store in accordance with local regulations. Store in a dry, cool and well-ventilated area away from direct sunlight. Avoid freezing. Store away from
incompatible materials (see Section 10) and food and drink. Store in original container. Keep container tightly closed when not in use. Containers that have
been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Provide appropriate fire extinguishers
and spill cleanup equipment in or nearstorage area. Keep unauthorized personnel away.
7.3 Specific end uses
See section 1.2
SECIION 8. Exposure controls/personal protection
8,1 Control parameters
lngredients with limit values that require monitoring:
Contains no substances with occupational exposure limit values
lngredients with biological monitoring guidance values (BMGV) and/or biological exposure index (BEl):
Contains no substances with biological monitoring guidance values.
8.2 Exposure controls
Revision dale: I/ L / 2O2L Version: 5.0 3/7
Safety Data Sheet PARTALL Hi-Temp Wax
Engineering controls
Provide adequate local exhaustventilation. Maintain eye wash fountain and safetyshower in work area
Personal protective equipment
General protective and hygenic measures
Do not eat, drink, or smoke while using. Wash hands before breaks and at the end of workday. lmmediately remove all soiled or contaminated clothing.
Eye and face protection
Chemical safety glasses with side shields, goggles or face shield are recommended. Eye wash stations are recommended for the work area
Skin and body protection
Wear chemical resistant clothing and shoes. Safety showers are recommended for the work area
Respiratory protection
Provide sufficient general and/or local exhaust. lf engineering controls are not sufficient to protect worker health use a respirator approved under applicable
regulatory standards.
Hand protection
Wear chemical resistant impervious gloves. 6love suitability and breakthrough time will differ depending on the specific use conditions. Contact the glove
manufacturer for specific advice on glove selection and breakthrough times for your use conditions. lnspect and replace worn or damaged gloves.
Environmental controls
Prevent product from entering drains. Stop spill at source and prevent further leakage or spillage if safe to do so. lf product contaminates rivers and lakes or
drains, notify proper authorities.
SECTION 9, Physical and chemical properties
Physical state
Physical form
Colour
Odour
Odour threshold
Melting point
Freezing point
lnitial boiling point and boiling range
Flammability
Upper flammability limit
Lower flammability limit
Flash point
Auto-ignition temperature
Decomposition temperature
pH
Viscosity
Solubility (water)
Partition coefficient n-octanoUwater (log value)
Vapour pressure
Relative density at 24’C {water = 1)
Volatile organic compounds (VOC)
VOC – actual
VOC less water & exempt solvents
SECTION 10. Stability and reactivity
10.1 Reactivity
Not reactive under normal conditions of use.
10.2 Chemical stability
Solid
Paste
White
Aliphatic
No data available
48’C (120 “F)
No data available
No data available
Not classified
Not applicable
Not applicable
> 80 “c (> 176’F)
No data available
No data available
No data available
Not applicable
Not soluble
No data available
No data available
0.75 – 0.80
:527 e/L
i 527 ElL
Revision dale:1h/2o21 Version: 5.0 4/7
Safety Data Sheet PARTALL Hi-Temp Wax
Stable under normal conditions of use.
10.3 Possibility of hazardous reactions
No dangerous reactions known under normal conditions of use.
10.4 Conditions to avoid
Avoid heat, sparks, open flames, hot surfaces, or other sources of ignition.
10.5 lncompatible materials
Strong oxidizing agents, strong acids, strong bases, reactive metals, halogenated compounds, aldehydes, alkali metals, alkaline earth metals
10.6 Hazardous decomposition products
Carbon oxides, fluorinated compounds
SECTION 11, Toxicological lnformation
11,1 lnformation on toxicological effects
Acute toxicity
LD/1C50 values that are relevant for classification:
Distillates (petroleum), hydrotreated light
CAS No. 64742-47-8
Skin corrosion/irritation
Serious eye damage/irritation
Respiratory or skin sensitisation
Germ cell mutagenicity
Carcinogenicity
Reproductive toxicity
STOT-single exposure
STOT-repeated exposure
Aspiration hazard
SECTION 12: Ecological information
Not classified
Expected to be slightly irritating
Expected to be slightly irritating
Not classified
Not classified
Not classified
Not classified
Not classified
Not classified
May be fatal if swallowed and enters airway
Not expected to be toxic.
Expected to be inherently biodegradable.
No data available
No data available
No data available
12.1 Toxicity
12.2 Persistence and degradability
12.3 Bioaccumulative potential
12.4 Mobility in soil
12.5 Other adverse effects
12.6 General notes No data available
SECTION 13. Disposal considerations
13.1 Waste treatment methods
Dispose of in accordance with regional, national, and local laws and regulations.
Materialdisposal
Container disposal
Do not dispose of waste into sewer. Do not contaminate ponds, waterways, or ditches with product or used
container. Send to a licensed waste management company.
Do not dispose of waste into sewer. Do not contaminate ponds, waterways, or ditches with product or used
container. Send to a licensed waste management company.
Oral LD5O rat > 5000 me/ks
Dermal LD5O rabbit 2000 – 4000 ms/ks
lnhalative LC50 rat > 0.5 me/ll4h
Revision dare: l/ I/ 2O2L Version: 5.0 s/7
Safety Data Sheet PARTALL Hi-Temp Wax
SECTION 14. Transport information
14.1 UN number
Not regulated
14.2 UN proper shipping name
DOT : Not regulated
ADR : Not regulated
IMDG : Not regulated
IATA : Not regulated
14.3 Transport hazard class
Not regulated
14.4 Packing group
Not regulated
14,5 Environmental hazards
Not regulated
14.6 Special precautions for user
Not regulated
14.7 Transport in bulk according to Annex ll of MARPOL and the IBC Code
Not regulated
14.8 Additional information
Not regulated
SECTION 15. Regulatory information
15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture
No information available for this material. lnformation provided is for components.
OSHA Hazard Communication Standard
This material is hazardous in accordance with OSHA HazCom 2OI2,29 CFR 191″0.1200
Superfund Amendments and Reauthorization Act (SARA)
SARA 302 Components
No chemicals in this material are subject to the reporting requirements of SARA Title lll, Section 302
SARA 311/3f2 Hazard Categories
lmmediate (acute) health hazard
SARA 313 Components
No chemicals in this material are subject to the reporting requirements of SARA Title lll, Section 313.
Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA)
No chemicals in this material are subject to the reporting requirements of CERCLA.
California Proposition 65
No chemicals in this material are subject to the reporting requirements of California Proposition 55.
This product contains the following Right to Know components
Component
Disti l lates ( petroleum), hydrotreated l ight (CAS No. 647 42- 47 -81
U.S. State Right to Know list
Massachusetts, New Jersey, Pennsylvania
Revision date: I / ll 2O2l Version: 5.0 6/7
Safety Data Sheet PARTALL Hi-Temp Wax
lnternational Agency for Research on Cancer (IARC)
This product contains the following chemicals classified by IARC as carcinogenic:
None known
Chemical inventories
Components are listed or exempted from listing on the following chemical inventories:
AICS Australian lnventory of Chemical Substances
DSL / NDSL Domestic Substances List / Non-Domestic Substances List
EINECS European lnventory of Existing Commercial Chemical Substances
ENCS Existing and New Chemical Substances
IECS lnventory of Existing Chemical Substances Produced or lmported in China
KECI Korea Existing Chemicals lnventory
NZIoC New Zealand lnventory of Chemicals
PICCS Philippine Inventory of Chemicals and Chemical Substances
TCSI Taiwan Chemical Substance lnventory
TSCA Toxic Substances Control Act
15.2 Chemical safety assessment
A chemical safety assessment has not been carried out for this product.
SECTION 16. other information
DTSCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. REXCO MAKES NO WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF
PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether this product is fit for a particular purpose and suitable for user’s method
of use or application. Given the variety of factors that can affect the use and application of a product, some of which are uniquely within the user’s
knowledge and control, it is essential that the user evaluate this product to determine whether it is fit for a particular purpose and suitable for user’s
method of use or application.
Abbreviations and acronyms
ADR
Asp. Tox. 1
cAs
DOT
IATA
IMDG
LC50
LD5O
NIOSH
OSHA
OSHA HCS
PBT
vPvB
European Agreement concerning the lnternational Carriage of Dangerous Goods by Road
Aspiration hazard – Category L
Chemical Abstract Service
U.S. Department of Transportation
I nternational Air Transport Association
lnternational Maritime Dangerous Goods
Lethal concentration, 50 percent
Lethal dose, 50 percent
National lnstitute for Occupational Safety and Health
U.S. Occupational Safety and Health Administration
U.S. Occupational Safety and Health Administration Hazard Communication Standard
Persistent, Bioaccuma lative and Toxic
very Persistent and very Bioaccumulative
Revision date: 1. /
L / 202L Version: 5.0 7/7