39XYLENE-D_TDS.pdf
39UCEQ_TDS.pdf
PRODUCT PROPERTIES
A
ll time calculations are based on temperatures of 77 F, 25 C
Flash Point 23 F
Specific Gravity .8gm/cc @ 20 C
Evaporation Rate > (n-b
Weight per gallon 6.65 lbs/gal
Vapor Pressure 41.3 mm hg
KEY USES
For use with all Duratec
products requiri
ng
thinning prior to use.
Can be used as a
reducer for most
standard Vinyl Ester or
Polyester Products.
A lso works as a solvent
for easy cleanup.
Duratec Reducer was specifically designed to thin and adapt to Duratec
products without altering its original properties. This product is a blend of
solvents formulated to enhance the flow and leveling of Duratec primers
and top coats.
FEATURES
EFFICIENCY
Small additions of Duratec
Reducer quickly cut the viscosity
of Duratec p rimers and topcoats .
R EDUCED ORANGE PEEL
Enhances flow and leveli ng
properties of Duratec primers and
hi-gloss coatings, resulting in
reduced porosity and or
ange
peel.
PER FECT MATCH
Matches the original solvent cut, assuring complete compatibility .
F AST EVAPORATION
Does not extend the cure time of the sprayed- out Duratec.
IMPROVES LEVELING
Will not create the rough surfac
e
associated with dry spray.
DRY PRODUCT
Low water content, avoids fogging
or dulling topcoats.
DURATEC REDUCER
PRODUCT # 39UCE
SAFETY & HANDLING
Duratec Reducer is extremely flammable. Do not apply near sparks, open flames
or heat. Keep area ventilated. Do not smoke. Avoid continuous breathing of vapor.
Duratec Reducer contains ingredients which could be harmful if mishandled.
Contact with skin and eyes should be avoided and necessary protective equipment
and clothing should be worn. Individuals should wash with soap and water before
eating or drinking. All containers should be properly labeled to prevent accidental
ingestion or improper disposal. Individuals should reseal any partly used material
back in the container. Store under cool, dry conditions and away from open flames
and high temperatures.
For more detailed instructions on storage, please see the MSDS sheet.
DESCRIPTION
909-546-1160
hawkeyesales@hawkeyeind.com
PO BOX 415,
BLOOMINGTON, CA 92316
WWW.DURATEC1.COM
DURATEC REDUCER
USE GUIDE | PRODUCT #39UCE
Limited/ warranty statement: Our products are intended for sale to industrial and commercial customers. We request that customers inspect and test our
products before use and satisfy themselves as to contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any
warranty of merchantability or fitness, nor is protection from any law or patent to be inferred. All patent rights are reserved. The exclusive remedy for all
proven claims is replacement of our materials and in no event shall we be liable for special, incidental or consequential damages.
WWW.DURATEC1.COM 909-546-1160 HAWKEYESALES@HAWKEYEIND.COM PO BOX 415, BLOOMINGTON, CA 92316www.duratec1.com
Use Instructions
Duratec products are manufactured to be used as is, directly out of the can. The right step may
be
adjusting your spray equipment tip size, rather than reducing the material.
However there are times reducing is necessary. In those situations we advocate reducing as
little as possible, start
ing with one ounce per quart.
(1)Thoroughly mix the Duratec product you plan to use. Most Duratec products require a
thorough mix for the product to be consistent. A paint shaker or drill mixer is best.
(2)If the viscosity of the Duratec is too high for spraying, add one ounce of Duratec Reducer per
quart. Mix and evaluate the viscosity. Usually no more than three ounces of Duratec Reducer are
necessary per quart.
(3)Catalyze and spray the Duratec once the desired result viscosity is achieved. For specific catalyst
information, please consult the Technical Data Sheet (TDS) of the Duratec product you are using.
FYI: Duratec Reducer 39UCE was formerly known as Duratec Thinner 39LAC-3. If you have material
labeled as 39LAC-3 on hand it is likely the product is outdated. Please reach out to our team.
DURATEC REDUCER
T
ROUBLESHOOTING | PRODUC T # 39UCE
Problem Cause Solution
Cold thinner
Warm thinner and/or Duratec product.
Failure to rapidly mix
into Duratec products
Continue to machine mix until fully
blended with Duratec products.
39UCEG_TDS.pdf
PRODUCT PROPERTIES
A
ll time calculations are based on temperatures of 77 F, 25 C
Flash Point 23 F
Specific Gravity .8gm/cc @ 20 C
Evaporation Rate > (n-b
Weight per gallon 6.65 lbs/gal
Vapor Pressure 41.3 mm hg
KEY USES
For use with all Duratec
products requiri
ng
thinning prior to use.
Can be used as a
reducer for most
standard Vinyl Ester or
Polyester Products.
A lso works as a solvent
for easy cleanup.
Duratec Reducer was specifically designed to thin and adapt to Duratec
products without altering its original properties. This product is a blend of
solvents formulated to enhance the flow and leveling of Duratec primers
and top coats.
FEATURES
EFFICIENCY
Small additions of Duratec
Reducer quickly cut the viscosity
of Duratec p rimers and topcoats .
R EDUCED ORANGE PEEL
Enhances flow and leveli ng
properties of Duratec primers and
hi-gloss coatings, resulting in
reduced porosity and or
ange
peel.
PER FECT MATCH
Matches the original solvent cut, assuring complete compatibility .
F AST EVAPORATION
Does not extend the cure time of the sprayed- out Duratec.
IMPROVES LEVELING
Will not create the rough surfac
e
associated with dry spray.
DRY PRODUCT
Low water content, avoids fogging
or dulling topcoats.
DURATEC REDUCER
PRODUCT # 39UCE
SAFETY & HANDLING
Duratec Reducer is extremely flammable. Do not apply near sparks, open flames
or heat. Keep area ventilated. Do not smoke. Avoid continuous breathing of vapor.
Duratec Reducer contains ingredients which could be harmful if mishandled.
Contact with skin and eyes should be avoided and necessary protective equipment
and clothing should be worn. Individuals should wash with soap and water before
eating or drinking. All containers should be properly labeled to prevent accidental
ingestion or improper disposal. Individuals should reseal any partly used material
back in the container. Store under cool, dry conditions and away from open flames
and high temperatures.
For more detailed instructions on storage, please see the MSDS sheet.
DESCRIPTION
909-546-1160
hawkeyesales@hawkeyeind.com
PO BOX 415,
BLOOMINGTON, CA 92316
WWW.DURATEC1.COM
DURATEC REDUCER
USE GUIDE | PRODUCT #39UCE
Limited/ warranty statement: Our products are intended for sale to industrial and commercial customers. We request that customers inspect and test our
products before use and satisfy themselves as to contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any
warranty of merchantability or fitness, nor is protection from any law or patent to be inferred. All patent rights are reserved. The exclusive remedy for all
proven claims is replacement of our materials and in no event shall we be liable for special, incidental or consequential damages.
WWW.DURATEC1.COM 909-546-1160 HAWKEYESALES@HAWKEYEIND.COM PO BOX 415, BLOOMINGTON, CA 92316www.duratec1.com
Use Instructions
Duratec products are manufactured to be used as is, directly out of the can. The right step may
be
adjusting your spray equipment tip size, rather than reducing the material.
However there are times reducing is necessary. In those situations we advocate reducing as
little as possible, start
ing with one ounce per quart.
(1)Thoroughly mix the Duratec product you plan to use. Most Duratec products require a
thorough mix for the product to be consistent. A paint shaker or drill mixer is best.
(2)If the viscosity of the Duratec is too high for spraying, add one ounce of Duratec Reducer per
quart. Mix and evaluate the viscosity. Usually no more than three ounces of Duratec Reducer are
necessary per quart.
(3)Catalyze and spray the Duratec once the desired result viscosity is achieved. For specific catalyst
information, please consult the Technical Data Sheet (TDS) of the Duratec product you are using.
FYI: Duratec Reducer 39UCE was formerly known as Duratec Thinner 39LAC-3. If you have material
labeled as 39LAC-3 on hand it is likely the product is outdated. Please reach out to our team.
DURATEC REDUCER
T
ROUBLESHOOTING | PRODUC T # 39UCE
Problem Cause Solution
Cold thinner
Warm thinner and/or Duratec product.
Failure to rapidly mix
into Duratec products
Continue to machine mix until fully
blended with Duratec products.
39UCEF_TDS.pdf
DURATEC REDUCER
P RO D UCT # 39UCE
909-546-1160
hawkeyesales@hawkeyeind.com
PO BOX 415,
BLOOMINGTON, CA 92316
WWW.HAWKEYEIND.COM
D ESC R I PT I O N
Duratec Reducer was specifically designed to thin and adapt to Duratec
products without altering its original properties. This product is a blend of
solvents formulated to enhance the flow and leveling of Duratec primers
and top coats.
KE Y U S ES
For use with all Duratec
products requiring
thinning prior to use.
Can be used as a
reducer for most
standard Vinyl Ester or
Polyester Products.
Also works as a solvent
for easy cleanup.
FE A TU R E S
EFFICIENCY
Small additions of Duratec
Reducer quickly cut the viscosity
of Duratec primers and topcoats.
REDUCED ORANGE PEEL
Enhances flow and leveling
properties of Duratec primers and
hi-gloss coatings, resulting in
reduced porosity and orange
peel.
PERFECT MATCH
Matches the original solvent cut,
assuring complete compatibility.
FAST EVAPORATION
Does not extend the cure time of
the sprayed-out Duratec.
IMPROVES LEVELING
Will not create the rough surface
associated with dry spray.
DRY PRODUCT
Low water content, avoids fogging
or dulling topcoats.
S A F E T Y & H AN D L I N G
Duratec Reducer is extremely flammable. Do not apply near sparks, open flames
or heat. Keep area ventilated. Do not smoke. Avoid continuous breathing of vapor.
Duratec Reducer contains ingredients which could be harmful if mishandled.
Contact with skin and eyes should be avoided and necessary protective equipment
and clothing should be worn. Individuals should wash with soap and water before
eating or drinking. All containers should be properly labeled to prevent accidental
ingestion or improper disposal. Individuals should reseal any partly used material
back in the container. Store under cool, dry conditions and away from open flames
and high temperatures.
For more detailed instructions on storage, please see the MSDS sheet.
Liability/warranty statement: Our products are intended for sale to industrial and commercial
customers. We request that customers inspect and test our products before use and satisfy themselves
as to contents and suitability. All claim requests must be made in writing and are subject to review,
including storage temperature verification and retain evaluations. The exclusive remedy for all proven
claims is replacement of our materials. In no event shall we be liable for special, incidental or
consequential damages, including damages caused in transit (exworks terms). Nothing herein shall
constitute a warranty, expressed or implied, including any warranty of merchantability or fitness, nor is
protection from any law or patent to be inferred. All patent and trademark rights reserved.
REVISED JUNE 2025
PRODUCT PROPERTIES
All time calculations are based on temperatures of 77 F, 25 C
Flash Point 23 F
Specific Gravity .8gm/cc @ 20 C
Evaporation Rate >(n-butyl acctate = 1)
Weight per gallon 6.65 lbs/gal
Vapor Pressure 41.3 mm hg
Color: clear
(slight hue present while in can)
Shelf life:
Twelve (12) months from date of
manufacture, unopened, with proper
storage .See Shelf Life Statement
for full details.
Use Instructions
Duratec products are manufactured to be used as is, directly out of the can. The right step may
be adjusting your spray equipment tip size, rather than reducing the material.
However there are times reducing is necessary. In those situations we advocate reducing as
little as possible, starting with one ounce per quart.
(1) Thoroughly mix the Duratec product you plan to use. Most Duratec products require a
thorough mix for the product to be consistent. A paint shaker or drill mixer is best.
(2) If the viscosity of the Duratec is too high for spraying, add one ounce of Duratec Reducer per
quart. Mix and evaluate the viscosity. Usually no more than three ounces of Duratec Reducer are
necessary per quart.
(3) Catalyze and spray the Duratec once the desired result viscosity is achieved. For specific catalyst
information, please consult the Technical Data Sheet (TDS) of the Duratec product you are using.
FYI: Duratec Reducer 39UCE was formerly known as Duratec Thinner 39LAC-3. If you have material
labeled as 39LAC-3 on hand the material is outdated and should be replaced with new product.
Our products are intended for sale to industrial and commercial customers. We request that customers inspect and test our products before use and
satisfy themselves as to contents and suitability. All claim requests must be made in writing and are subject to review, including storage temperature
verification and retain evaluations. The exclusive remedy for all proven claims is replacement of our materials. In no event shall we be liable for special,
incidental or consequential damages, including damages caused in transit (exworks terms). Nothing herein shall constitute a warranty, expressed or
implied, including any warranty of merchantability or fitness, nor is protection from any law or patent to be inferred. All patent and trademark rights
reserved.
www.hawkeyeind.com
DURATEC REDUCER
USE GUIDE
WWW.HAWKEYEIND.COM 909-546-1160 HAWKEYESALES@HAWKEYEIND.COM PO BOX 415, BLOOMINGTON, CA 92316
Problem Solution
blended with Duratec products.
Cold thinner
Failure to rapidly mix
into Duratec products
Cause
DURATEC REDUCER
TROUBLESHOOTING
39UCED_TDS.pdf
PRODUCT PROPERTIES
A
ll time calculations are based on temperatures of 77 F, 25 C
Flash Point 23 F
Specific Gravity .8gm/cc @ 20 C
Evaporation Rate > (n-b
Weight per gallon 6.65 lbs/gal
Vapor Pressure 41.3 mm hg
KEY USES
For use with all Duratec
products requiri
ng
thinning prior to use.
Can be used as a
reducer for most
standard Vinyl Ester or
Polyester Products.
A lso works as a solvent
for easy cleanup.
Duratec Reducer was specifically designed to thin and adapt to Duratec
products without altering its original properties. This product is a blend of
solvents formulated to enhance the flow and leveling of Duratec primers
and top coats.
FEATURES
EFFICIENCY
Small additions of Duratec
Reducer quickly cut the viscosity
of Duratec p rimers and topcoats .
R EDUCED ORANGE PEEL
Enhances flow and leveli ng
properties of Duratec primers and
hi-gloss coatings, resulting in
reduced porosity and or
ange
peel.
PER FECT MATCH
Matches the original solvent cut, assuring complete compatibility .
F AST EVAPORATION
Does not extend the cure time of the sprayed- out Duratec.
IMPROVES LEVELING
Will not create the rough surfac
e
associated with dry spray.
DRY PRODUCT
Low water content, avoids fogging
or dulling topcoats.
DURATEC REDUCER
PRODUCT # 39UCE
SAFETY & HANDLING
Duratec Reducer is extremely flammable. Do not apply near sparks, open flames
or heat. Keep area ventilated. Do not smoke. Avoid continuous breathing of vapor.
Duratec Reducer contains ingredients which could be harmful if mishandled.
Contact with skin and eyes should be avoided and necessary protective equipment
and clothing should be worn. Individuals should wash with soap and water before
eating or drinking. All containers should be properly labeled to prevent accidental
ingestion or improper disposal. Individuals should reseal any partly used material
back in the container. Store under cool, dry conditions and away from open flames
and high temperatures.
For more detailed instructions on storage, please see the MSDS sheet.
DESCRIPTION
909-546-1160
hawkeyesales@hawkeyeind.com
PO BOX 415,
BLOOMINGTON, CA 92316
WWW.DURATEC1.COM
DURATEC REDUCER
USE GUIDE | PRODUCT #39UCE
Limited/ warranty statement: Our products are intended for sale to industrial and commercial customers. We request that customers inspect and test our
products before use and satisfy themselves as to contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any
warranty of merchantability or fitness, nor is protection from any law or patent to be inferred. All patent rights are reserved. The exclusive remedy for all
proven claims is replacement of our materials and in no event shall we be liable for special, incidental or consequential damages.
WWW.DURATEC1.COM 909-546-1160 HAWKEYESALES@HAWKEYEIND.COM PO BOX 415, BLOOMINGTON, CA 92316www.duratec1.com
Use Instructions
Duratec products are manufactured to be used as is, directly out of the can. The right step may
be
adjusting your spray equipment tip size, rather than reducing the material.
However there are times reducing is necessary. In those situations we advocate reducing as
little as possible, start
ing with one ounce per quart.
(1)Thoroughly mix the Duratec product you plan to use. Most Duratec products require a
thorough mix for the product to be consistent. A paint shaker or drill mixer is best.
(2)If the viscosity of the Duratec is too high for spraying, add one ounce of Duratec Reducer per
quart. Mix and evaluate the viscosity. Usually no more than three ounces of Duratec Reducer are
necessary per quart.
(3)Catalyze and spray the Duratec once the desired result viscosity is achieved. For specific catalyst
information, please consult the Technical Data Sheet (TDS) of the Duratec product you are using.
FYI: Duratec Reducer 39UCE was formerly known as Duratec Thinner 39LAC-3. If you have material
labeled as 39LAC-3 on hand it is likely the product is outdated. Please reach out to our team.
DURATEC REDUCER
T
ROUBLESHOOTING | PRODUC T # 39UCE
Problem Cause Solution
Cold thinner
Warm thinner and/or Duratec product.
Failure to rapidly mix
into Duratec products
Continue to machine mix until fully
blended with Duratec products.
39SURF103G_TDS.pdf
Our Products are intended for sale to industrial and commercial customers. We request that Customers inspect and test our products before use and satisfy themselves as to
contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any warranty or merchantability or fitness, nor is protection from any
law of patent to be inferred. All patent rights are reserved. The exclusive remedy for all proven claims is replacement of our materials and in no event shall we be liable for
special , incidental or consequential damages
02/02/2021 ISO 9001:2015 Registered Company
DURA TECHNOLOGIES
39SURF103 & 39SURF102
World Class Coatings
Technology GEL COAT SURFACING
ADDITIVE
____________________________________________________________________________________________
DURA TECHNOLOGIES, INC. 10% Surfacing Agent is manufactured using high
quality materials and tight production controls. The wax used in this product is the best
available 125 F surfacing wax currently on the market. This material is frequently used
for gel coat repairs and for corrosion resistant hot coats where it is necessary to have a well
cured non-air inhibited surface
Coating Characteristics:
weight per gallon 7.35 lbs
V.O.C. 786 grams/liter
Shelf Life 6 months
Film Characteristics:
Melting point 125 F
Application:
1. 39SURF103 and 39SURF102 Surfacing Agent is ready to use as received.
2. If there is a trace of haze or surfacing wax on the surfacing agent warm it with hot
water to about 80 F until the turbidity disappears.
3. Add 2 percent by weight surfacing agent to the resin or gel coat to be air cured and
thoroughly mix before using.
4. Catalyze the resin or gel coat as recommended by the manufacturer and apply as
desired.
WARNING:
Once the surfacing agent is added to a material, that material can not be top coated
unless the surface is sanded until all of the wax is completely removed.
Disclaimer:
The information included in this technical bulletin is believed to be accurate and representative of
the product in general but is not a certification of any specific batch. This bulletin is provide as a
service and is not intended as a specification or as a warranty of performance.
39SUR10202_TDS.pdf
Our Products are intended for sale to industrial and commercial customers. We request that Customers inspect and test our products before use and satisfy themselves as to
contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any warranty or merchantability or fitness, nor is protection from any
law of patent to be inferred. All patent rights are reserved. The exclusive remedy for all proven claims is replacement of our materials and in no event shall we be liable for
special , incidental or consequential damages
02/02/2021 ISO 9001:2015 Registered Company
DURA TECHNOLOGIES
39SURF103 & 39SURF102
World Class Coatings
Technology GEL COAT SURFACING
ADDITIVE
____________________________________________________________________________________________
DURA TECHNOLOGIES, INC. 10% Surfacing Agent is manufactured using high
quality materials and tight production controls. The wax used in this product is the best
available 125 F surfacing wax currently on the market. This material is frequently used
for gel coat repairs and for corrosion resistant hot coats where it is necessary to have a well
cured non-air inhibited surface
Coating Characteristics:
weight per gallon 7.35 lbs
V.O.C. 786 grams/liter
Shelf Life 6 months
Film Characteristics:
Melting point 125 F
Application:
1. 39SURF103 and 39SURF102 Surfacing Agent is ready to use as received.
2. If there is a trace of haze or surfacing wax on the surfacing agent warm it with hot
water to about 80 F until the turbidity disappears.
3. Add 2 percent by weight surfacing agent to the resin or gel coat to be air cured and
thoroughly mix before using.
4. Catalyze the resin or gel coat as recommended by the manufacturer and apply as
desired.
WARNING:
Once the surfacing agent is added to a material, that material can not be top coated
unless the surface is sanded until all of the wax is completely removed.
Disclaimer:
The information included in this technical bulletin is believed to be accurate and representative of
the product in general but is not a certification of any specific batch. This bulletin is provide as a
service and is not intended as a specification or as a warranty of performance.