by | Sep 27, 2025
TECHNICAL DATA SHEET
SikaBiresin AP017 RR
February 19, Version 02 /2019
1
TECHNICAL DATA SHEET
SikaBiresin AP017 RR
(FORMERLY P-17 RR)
POLYESTER RESIN
REDUCER RESIN FOR P-17
DESCRIPTION
The SikaBiresin AP017 RR REDUCER RESIN is a polyester resin system with heat resistance of 446 F (230 C) developed to reduce
the viscosity of SikaBiresin AP017 (Formerly P-17) High Heat Resistant Filler Paste. SikaBiresin AP017 RR Reducer Resin can be
added to SikaBiresin AP017 Filler in varying amounts to “customize” the SikaBiresin AP017 Filler anywhere from a thin runny
paste to a sprayable consistency without altering the physical properties or the quick set work life. It is recommended to
experiment with 5% by weight addition or less to stay closer to the SikaBiresin AP017 Filler cured properties. The
SikaBiresin AP017 RR also performs very well in applications requiring a quick setting, high temperature polyester laminating resin.
PROPERTIES
High service temperature
Styrene-free
Exceptional adhesion
Impact and chemical resistant
TECHNICAL DATA SHEET
SikaBiresin AP017 RR
February 19, Version 02 /2019
2
PHYSICAL PROPERTIES
Composition POLYESTER
SikaBiresin AP017RR
BPO HARDENER MIXED
Mix ratio by weight
Mix ratio by volume at 25 C
100 2
Aspect Liquid Cream Paste Liquid
Viscosity (cps) 1,000
Color NOTE – Mixed color can be
varied with Cream BPO color
Clear Amber White
Red
Black
Specific gravity at 25 C lbs./gal
(g/cc)
ASTM D792 9.07
(1.09)
Pot Life at 25 C (102 g) (minutes) ASTM D2471 11
NOTE – SikaBiresin AP017 RR Can be used alone to thin P-17 or with 2% BPO cream hardener for laminating applications. BPO
cream hardener is not sold with the P-17 Reducer Resin.
TECHNICAL DATA SHEET
SikaBiresin AP017 RR
February 19, Version 02 /2019
3
PROCESSING
PROCESSING CONDITIONS
Thoroughly blend 100 parts resin with 2 parts hardener by weight for 1 to 1 minutes in clean
dry container
HANDLING PRECAUTIONS
Normal health and safety precautions should be observed when handling these products:
Ensure good ventilation.
Wear gloves, glasses and protective clothes.
For further information, please consult the Safety Data Sheets.
STORAGE CONDITIONS
Product shelf life of polyester resin is 12 months when stored in original unopened containers
between 65 77 F (15 25 C). Any opened can must be tightly closed. Product shelf life of BPO
hardener is 18 months when stored in original unopened containers between 65 77 F (15 25 C).
Any opened can must be tightly closed.
PACKAGING
Packaging information on request, please contact your local sales representative or find your local
contact on www.sikaadvancedresins.us
TECHNICAL DATA SHEET
SikaBiresin AP017 RR
February 19, Version 02 /2019
4
LEGAL NOTICE
The information, and, in particular, the recommendations relating to the application and end-use of
Sika products, are given in good faith based on Sika s current knowledge and experience of the products
when properly stored, handled and applied under normal conditions in accordance with Sika s
recommendations. In practice, the differences in materials, substrates and actual site conditions are
such that no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability
arising out of any legal relationship whatsoever, can be inferred either from this information, or from
any written recommendations, or from any other advice offered. The user of the product must test the
product s suitability for the intended application and purpose. Sika reserves the right to change the
properties of its products. The proprietary rights of third parties must be observed. All orders are
accepted subject to our current terms of sale and delivery. Users must always refer to the most recent
issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on
request.
CONTACT ADVANCED RESINS
GERMANY
Stuttgarter Stra e 139
72574 Bad Urach GERMANY
Tel.: (+49) 7 125 940 492
Fax. : (+49) 7 125 940 401
E-mail : tooling@de.sika.com
Website : www.sikaadvancedresins.de
FRANCE
ZI des B thunes – 15, Rue de l Equerre
95310 Saint-Ouen-l Aum ne
CS 40444
95005 CERGY PONTOISE Cedex FRANCE
Tel.: (+33) 1 344 034 60
Fax: (+33) 1 342 197 87
E-mail: advanced.resins@fr.sika.com
Website : www.sikaadvancedresins.fr
SPAIN
Pol gon Industrial Congost – Guardaagulles, 8
08520 LES FRANQUESES DEL VALLES SPAIN
Tel.: (+34) 932 25 16 20
E-mail: spain@axson.com
Website: www.sikaadvancedresins.es
ITALY
Via Morandi 15
21047 Saronno (Va) ITALY
Tel.: (+39) 02 9670 2336
Fax: (+39) 02 9670 2369
E-mail: axson@axson.it
Website: www.sikaadvancedresins.it
UNITED KINGDOM
Unit 15 Studlands Park Ind. Estate
Newmarket Suffolk, CB8 7AU UNITED KINGDOM
Tel.: (+44) 1638 660 062
Fax: (+44) 1638 665 078
E-mail: sales.uk@axson.com
Website: www.sikaadvancedresins.uk
SLOVAKIA
Tovarenska 49
95301 ZLATE MORAVCE SLOVAKIA
Tel: (+421) 376 422 526
Fax: (+421) 376 422 527
E-mail: axson.sk@axson.com
Web site: www.sikaadvancedresins.sk
UNITED STATES
30800 Stephenson Highway
Madison Heights, Michigan 48071 USA
Tel.: (+1) 248 588-2270
Fax: (+1) 248 577-0810
E-mail: axsonmh@axson.com
Web site: www.sikaadvancedresins.us
MEXICO
Ignacio Ram rez #20
Despacho 202 Col. Tabacalera
C.P. 06030 CDMX MEXICO
Tel.: (+52) 55 5264 4922
Fax: (+52) 55 5264 4916
E-mail: marketing@axson.com.mx
Website: www.sikaadvancedresins.mx
CHINA
N 53 Tai Gu Road
Wai Gao Qiao
Free Trade Zone, Pudong
200131 Shanghai CHINA
T l.: (+86) 21 5868 3037
Fax: (+86) 21 5868 2601
E-mail: marketing.china@axson.com
Website: www.sikaadvancedresins .cn
JAPAN
2-5-12 Onishi Okazaki Aichi
444-0871 JAPAN
Tel.: (+81) 564 26 2591
Fax: (+81) 564 26 2593
E-mail: sales.japan@axson.com
Website: www.sikaadvancedresins.jp
INDIA
Office n 8, Building Symphony C – 3rd Floor
Range Hills Road
Bhosale Nagar
PUNE 411 020 INDIA
Tel: (+ 91) 20 25 56 07 10
Fax: (+ 91) 20 25 56 07 12
E-mail: info.india@axson.com
Website: www.sikaadvancedresins.in
by | Sep 27, 2025
TECHNICAL DATA SHEET
SikaBiresin AP014
February 19, Version 02 /2019
1
TECHNICAL DATA SHEET
SikaBiresin AP014
February 19, Version 02 /2019
1
TECHNICAL DATA SHEET
SikaBiresin AP014
(FORMERLY P-14)
POLYESTER FILLER S YSTEM
MACHINABLE / RIGID
DESCRIPTION
The most versatile of all set-fast filler pastes, AP014 ULTRA FILLER is a two component filler system which
yields a smooth, creamy, thixotropic and workable paste with superior handling, set-fast characteristics
and dimensional stability. Once applied it forms a rigid, strong surface which can be machined, sanded,
filed or scraped to a feather edge. A P014 adheres and bonds to fiberglass, SMC, RIM, BMC, Graphite,
Kevlar
and other types of composites as well as aluminum, steel, grey iron, copper, plaster, models,
patterns and other substrates. AP014 offers the industry manufacturer a wide variety of applications for
bonding, filling, sealing and finishing with optimum physical properties. AP014 ULTRA FILLER can be
applied without pin-holing and exhibits no shrink or sink after curing. It accepts virtually all types of
finishes e.g., lacquer, enamel, polyurethane, epoxy, etc., without any special surface preparation. It is a
“no bleed out” system after finishing or if covered with a decorative film. Its high quality, coupled with
the set-fast feature offers industry substantial savings in time and labor plus top quality in the finished
product. AP014 can be used in areas of final fabrication, production, tooling, model & pattern making,
repair operations and in many other applications. Typical applications include: filling composites surface
porosity, honeycomb panel edge filler, bonding loose pieces and details, vacuum mold repair and
modifications, urethane mold repairs and modifications, FRP composite repairs, pattern repairs and
fillets, core box repairs and modifications, void and porosity filling, router fixture repairs, crack, dent and
crevice repair, temporary holding fixtures, filling cloth impressions in pre-preg, non-conductive barrier
potting, RIM/SMC/BMC surface filler, bonding inserts/hangers, urethane part repair, potting stripped
threads, renewing worn surfaces and many others.
PROPERTIES
Very quick setting
Comes in white and gray colors
Dimensionally stable
Excellent finishing and machinability
Easy to use
Good adhesion
TECHNICAL DATA SHEET
SikaBiresin AP014
February 19, Version 02 /2019
2
PHYSICAL PROPERTIES
Composition POLYESTER
SikaBiresin AP 014
BPO HARDENER
BPO
MIXED
Mix ratio by weight
Mix ratio by volume at 25 C
100 2
Aspect Paste Cream Paste Paste
Color NOTE – Mixed color can be
varied with Cream BPO color
(As a mixing aid/indicator and
final color choice)
White
Gray
White
Red
Black
Viscosity at 25 C (cPs) BROOKFIELD LVT Paste
Specific gravity at 25 C lbs./gal
(g/cc)
ASTM D792 13.4
(1.61)
10.0
(1.20)
13.30
(1.60)
Pot Life at 25 C (102 g) (minutes) ASTM D2471 4.0 6.0
MECHANICAL PROPERTIES at 23 C
(1)
Hardness (Shore D) ASTM D-2240 86
Water absorption 24 hr/R.T. soak (%) ASTM D-570 0.16
Adhesive pull strength (psi)
Aluminum
Polyester filler
Mahogany
Epoxy glass laminate
ASTM D-4541
2,940
1,717
1,459
753
(1)
Average values obtained on standard specimens / Cured 7 days at 25 C
CHEMICAL RESISTANCE GUIDE
AP014 Ultra Filler combines saturated and unsaturated Polyester resins of medium to high reactivity. As an aid to the user,
chemical resistance evaluations were conducted using a modification of ASTM 0543-60T.
TESTING PROCEDURE
Samples nominally sized at 1/2″ x 1″ x 4″ were immersed halfway in 4 ounces of reagent and stored for 12 months at ambient
temperature. Reagents were swirled monthly, and specimens were rated every 4 weeks.
RATING RESULTS
Excellent, No Visible Attack Good, Very Slight Attack Not Recommended
Benzene
Gasoline
Methanol
Mineral Spirits
Water (Distilled)
Acetic Acid (5%)
Citric Acid
Hydrochloric Acid (10%)
Nitric Acid (10%)
Sodium Hydroxide (5%)
Sulfuric Acid (10%)
Acetone
TECHNICAL DATA SHEET
SikaBiresin AP014
February 19, Version 02 /2019
3
PROCESSING
PROCESSING CONDITIONS
Thoroughly blend 100 parts resin with 2 parts hardener by weight for 1 to 1 minutes in clean
dry container or on a clean dry surface.
Carefully scrape the surfaces while blending to ensure complete mixing and uniformity.
SURFACE PREPARATION and APPLICATION
The area to be filled or repaired should be thoroughly cleaned, roughened, cleaned again
and dried to allow for the best possible adhesion.
The mixed A P014 should be buttered into the area, avoiding trapping air during application.
After curing to a tack-free state, the material can be sanded and finished as needed.
MIXING INSTRUCTIONS
Stir contents of can thoroughly using a spatula or putty knife. Place the required amount of filler
and cream hardener on a disposable clean surface. Mix 100 parts paste to 2 parts BPO cream
hardener by weight; i.e. approximatly size of golf ball (paste) to a two inch strip of BPO catalyst. Set
up time of mix at room temperature will be 5-10 minutes. After 15-20 minutes the filler may be
filed or sanded to final finish.
HANDLING PRECAUTIONS
Normal health and safety precautions should be observed when handling these products :
Ensure good ventilation.
Wear gloves, glasses and protective clothes.
For further information, please consult the Safety Data Sheets.
STORAGE CONDITIONS
Product shelf life of polyester resin is 12 months when stored in original unopened containers
between 65 77 F (15 25 C). Any opened can must be tightly closed. Product shelf life of BPO
hardener is 18 months when stored in original unopened containers between 65 77 F (15 25 C).
Any opened can must be tightly closed.
Polyester resin contains filler which has the potential to separate in time, please re-homogenize
prior to use.
PACKAGING
Packaging information on request, please contact your local sales representative or find your local
contact on www.sikaadvancedresins.us
TECHNICAL DATA SHEET
SikaBiresin AP014
February 19, Version 02 /2019
4
LEGAL NOTICE
The information, and, in particular, the recommendations relating to the application and end-use of
Sika products, are given in good faith based on Sika s current knowledge and experience of the products
when properly stored, handled and applied under normal conditions in accordance with Sika s
recommendations. In practice, the differences in materials, substrates and actual site conditions are
such that no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability
arising out of any legal relationship whatsoever, can be inferred either from this information, or from
any written recommendations, or from any other advice offered. The user of the product must test the
product s suitability for the intended application and purpose. Sika reserves the right to change the
properties of its products. The proprietary rights of third parties must be observed. All orders are
accepted subject to our current terms of sale and delivery. Users must always refer to the most recent
issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on
request.
CONTACT ADVANCED RESINS
GERMANY
Stuttgarter Stra e 139
72574 Bad Urach GERMANY
Tel.: (+49) 7 125 940 492
Fax. : (+49) 7 125 940 401
E-mail : tooling@de.sika.com
Website : www.sikaadvancedresins.de
FRANCE
ZI des B thunes – 15, Rue de l Equerre
95310 Saint-Ouen-l Aum ne
CS 40444
95005 CERGY PONTOISE Cedex FRANCE
Tel.: (+33) 1 344 034 60
Fax: (+33) 1 342 197 87
E-mail: advanced.resins@fr.sika.com
Website : www.sikaadvancedresins.fr
SPAIN
Pol gon Industrial Congost – Guardaagulles, 8
08520 LES FRANQUESES DEL VALLES SPAIN
Tel.: (+34) 932 25 16 20
E-mail: spain@axson.com
Website: www.sikaadvancedresins.es
ITALY
Via Morandi 15
21047 Saronno (Va) ITALY
Tel.: (+39) 02 9670 2336
Fax: (+39) 02 9670 2369
E-mail: axson@axson.it
Website: www.sikaadvancedresins.it
UNITED KINGDOM
Unit 15 Studlands Park Ind. Estate
Newmarket Suffolk, CB8 7AU UNITED KINGDOM
Tel.: (+44) 1638 660 062
Fax: (+44) 1638 665 078
E-mail: sales.uk@axson.com
Website: www.sikaadvancedresins.uk
SLOVAKIA
Tovarenska 49
95301 ZLATE MORAVCE SLOVAKIA
Tel: (+421) 376 422 526
Fax: (+421) 376 422 527
E-mail: axson.sk@axson.com
Web site: www.sikaadvancedresins.sk
UNITED STATES
30800 Stephenson Highway
Madison Heights, Michigan 48071 USA
Tel.: (+1) 248 588-2270
Fax: (+1) 248 577-0810
E-mail: axsonmh@axson.com
Web site: www.sikaadvancedresins.us
MEXICO
Ignacio Ram rez #20
Despacho 202 Col. Tabacalera
C.P. 06030 CDMX MEXICO
Tel.: (+52) 55 5264 4922
Fax: (+52) 55 5264 4916
E-mail: marketing@axson.com.mx
Website: www.sikaadvancedresins.mx
CHINA
N 53 Tai Gu Road
Wai Gao Qiao
Free Trade Zone, Pudong
200131 Shanghai CHINA
T l.: (+86) 21 5868 3037
Fax: (+86) 21 5868 2601
E-mail: marketing.china@axson.com
Website: www.sikaadvancedresins .cn
JAPAN
2-5-12 Onishi Okazaki Aichi
444-0871 JAPAN
Tel.: (+81) 564 26 2591
Fax: (+81) 564 26 2593
E-mail: sales.japan@axson.com
Website: www.sikaadvancedresins.jp
INDIA
Office n 8, Building Symphony C – 3rd Floor
Range Hills Road
Bhosale Nagar
PUNE 411 020 INDIA
Tel: (+ 91) 20 25 56 07 10
Fax: (+ 91) 20 25 56 07 12
E-mail: info.india@axson.com
Website: www.sikaadvancedresins.in
by | Sep 27, 2025
by | Sep 27, 2025
by | Sep 27, 2025
AXSON TECHNOLOGIES US
+1 248 588 2270
axsonmh@axson.com
axson-na.com
CHINA
+86 21 58 68 30 37
marketing.china@axson.com
GERMANY
+49 6 07 44 07 11-0
verkauf@axson.com
INDIA
+91 20 25 56 07 10-11
info.india@axson.com
ITALY
+39 02 96 70 23 36
axson@axson.it
JAPAN
+81 5 64 26 25 91
sales.japan@axson.com
FRANCE
Global Headquarters
+33 1 34 40 34 60
axson@axson.com
axson-technologies.com
MEXICO
+52 55 52 64 49 22
marketing@axson.com.mx
MIDDLE EAST
+971 7 2432227
axsonmideast@axson.com
SLOVAKIA
+42 1 76 42 25 26
axson.sk@axson.com
SPAIN
+34 9 32 25 16 20
spain@axson.com
U.K.
+44 16 38 66 00 62
sales.uk@axson.com
PRODUCT BULLETIN
www.axson-technologies.com 800.344.7776 axsonmh@axson.com
31200 Stephenson Hwy Madison Heights, MI 48071 Ph 248.588.2270 Fax 248.588.5909
DESCRIPTION:
Fast Patch Paste TCC-5220 A/B is a two-part system designed to quickly make repairs or modifications to the PP-1052 Pattern Plank
.
This material is available in convenient self-mixing cartridges for ease of use. A dispensing gun must be used to dispense this material.
Patch Paste TCC-5220 A/B will cure rapidly and can be machined or sanded in approximately 15 – 20 minutes.
TYPICAL HANDLING CHARACTERISTICS @ 77 F (25 C)
Mix Ratio (by weight or volume) ………………………………………………………………….. Resin TCC-5220A ……………………….100 parts
………………………………………………………………………………………………………………. Hardener TCC-5220B ………………….100 parts
Pot Life (50 gram mass) …………………………………………………………………………………………………………………………………3 minutes
Hardness ……………………………………………………………………………………………………………………………………………………..80 – 85 Shore D
Viscosity ………………………………………………………………………………………………….. Resin TCC-5220A ……………………….26,000 cps
………………………………………………………………………………………………………………. Hardener TCC-5220B ………………….20,000 cps
………………………………………………………………………………………………………………. Mixed Viscosity …………………………..Paste
Specific Gravity …………………………………………………………………………………………………………………………………………….1.03g/cc
Color ……………………………………………………………………………………………………….. Resin TCC-5220A ……………………….Brown
………………………………………………………………………………………………………………. Hardener TCC-5220B ………………….Red
………………………………………………………………………………………………………………. Mixed Color ………………………………..Red
Machinability …………………………………………………………………………………………………………………………………………………Good
Time to Machine or Sand (depending on temperature) ……………………………………………………………………………………….15 – 20 minutes
Shelf Life (in original unopened containers) ………………………………………………….. TCC-5220A/TCC-5220B ………………2 years
Standard Size Available: 50ml cartridge
SANITARY PRECAUTIONS:
Do not take internally. Avoid prolonged breathing of vapors. Work in a well-ventilated area. Avoid skin contact. Protective gloves
should be worn. If contact occurs: wash skin with soap and water. Avoid eye contact. If contact occurs: rinse well with water for 15
minutes, contact physician.
STORAGE AND HANDLING:
To avoid moisture contamination, with each new nozzle purge small amount of material. Store at room temperature.
TCC-5220 Tech/Revised 1/30/15
Supersedes 6/20/14
The information contained in this technical data sheet results from research and tests conducted in our laboratories under precise conditions. Seller
cannot anticipate all conditions under which seller s products, or the products of other manufacturers in combination with seller s products, may be used.
It is the responsibility of the user to determine the suitability of the Axson Technologies products, under their own conditions, before commencing with
the proposed application. In no event shall Axson Technologies, Inc. be liable for any direct, indirect, punitive, incidental, special, and/or consequential
damages, to property or life, whatsoever arising out of or connected with the use or misuse of our products.
TCC-5220 A/B
FAST PATCH PASTE
FOR PP-1052
PATTERN PLANK
by | Sep 27, 2025
TECHNICAL DATA SHEET
TCC-410
February 19, Version 01 /2021
1
TECHNICAL DATA SHEET
TCC-410
February 19, Version 01 /2021
1
TECHNICAL DATA SHEET
TCC-410
SURFACE/MASS CASTING SYSTEM
IMPACT RESISTANT
DESCRIPTION
Epoxy Resin TCC-410 is an aluminum filled system designed for high-impact resistance. This system can be surface
cast to metal or other low-cost cores or it may be mass casted. Depending on thickness of cast, a choice of hardeners
is provided to control exothermic heat and shrinkage. Applications for this system include casting surfaces on
prototype stamping dies or mass casting applications where high-impact resistance is desired.
APPLICATIONS
Casting surfaces on prototype stamping dies
Mass casting applications
TECHNICAL DATA SHEET
TCC-410
February 19, Version 01 /2021
2
PHYSICAL PROPERTIES
Thickness of Cast > Surface Cast – 1 Mass Cast 1 – 4 Mass Cast 4 – 10
Hardener Selection TCC-104 TCC-104-5 TCC-105
Mix Ratio (parts by weight):
Resin TCC-410 100 parts 100 parts 100 parts
Hardener 10 parts 10 parts 10 parts
Pot Life (500 gram mass) 60 minutes 100 minutes 2 – 3 hours
Peak Exotherm 200 F (93 C)
Peak Operating Temperature 180 F (82 C) 210 F (99 C) 240 F (116 C)
Cure Time 8 – 12 hours 18- 36 hours 48 – 72 hours
TYPICAL PHYSICAL PROPERTIES with TCC-104 H @ 77 F (25 C) Cured 7 days @ R.T.
Specific Gravity (g/cc) 1.65
Mixed Viscosity – (cps & mPa.s)_ 6,000
Cured Color – Visual Aluminum – Gray
Hardness – (Shore D) 84
Linear Shrinkage (in/in) 0.0015
Notched Izod Impact Strength – (ft lbs/in) 8.5
Tensile Strength – psi (MPa) 7,000 (48)
Shelf Life (in original unopened containers) TCC-401/TCC-104, TCC-104-5, or TCC-105
2
years
HANDLING PRECAUTIONS
Normal health and safety precautions should be observed when handling these products:
Ensure good ventilation.
Wear gloves, glasses and protective clothes.
For further information, please consult the Safety Data Sheets.
STORAGE CONDITIONS
This product has a shelf life of 24 months for the resin and hardener as indicated by the
expiration date on the container when stored in original unopened containers.
PACKAGING
Packaging information on request, please contact your local sales representative or find your
local contact on www.sikaadvancedresins.us
LEGAL NOTICE
The information, and, in particular, the recommendations relating to the application and
end-use of Sika products, are given in good faith based on Sika s current knowledge and
experience of the products when properly stored, handled and applied under normal
conditions in accordance with Sika s recommendations. In practice, the differences in
materials, substrates and actual site conditions are such that no warranty in respect of
merchantability or of fitness for a particular purpose, nor any liability arising out of any legal
relationship whatsoever, can be inferred either from this information, or from any written
recommendations, or from any other advice offered. The user of the
TECHNICAL DATA SHEET
TCC-410
February 19, Version 01 /2021
3
product must test the product s suitability for the intended application and purpose. Sika
reserves the right to change the properties of its products. The proprietary rights of third
parties must be observed. All orders are accepted subject to our current terms of sale and
delivery. Users must always refer to the most recent issue of the local Product Data Sheet
for the product concerned, copies of which will be supplied on request.
CONTACT
UNITED STATES
Sika Corporation
30800 Stephenson Highway
Madison Heights, Michigan 48071 USA
Tel.: (+1) 248 588-2270
Fax: (+1) 248 577-0810
E-mail: advanced.resins@us.sika.com
Website: www.sikaadvancedresins.us
by | Sep 27, 2025
TC-4485 A/B Page 1 of 2 Date: 12/18/2015
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
www.bjbenterprises.com
Quality Management
System Registered
to ISO 9001:2008
TC-4485 A/B
IRON-FILLED EPOXY MASS CASTING SYSTEM
TC-4485 A/B is a room temperature curing, mass castable epoxy resin system that produces a tough, dense, low shrink solid
material with fine detail reproduction. TC-4485 A/B is designed for single-pour castings up to 3″ thick, or for thicker castings up
to 8″ using a stage pour procedure.
Slower reacting system designed for thicker casts Improved viscosity for easier pouring
TYPICAL PRODUCT USES :
Molds Patterns
Cast Parts Form Dies
PHYSICAL PROPERTIES TEST METHOD TEST RESULTS
Hardness, Shore D ASTM D2240 85 2
Density (g/cc) ASTM D792 2.1
Cubic Inches per Pound N/A 13.1
Tensile Modulus (psi) ASTM D638 5.2 x 10
7
Flexural Strength (psi) ASTM D790 9,450
Flexural Modulus (psi) ASTM D790 3.2 x 10
5
Izod Impact (ft-lb/in) ASTM D256 2.0
Shrinkage (in/in) ASTM D2566 <0.001
Compressive Strength (psi) ASTM D695 13,320
Coefficient of Thermal Expansion (in/in/F ) ASTM D3386 3.0 x 10
-5
HANDLING PROPERTIES Part A Part B
Mix Ratio by weight 100 8
Mix Ratio by volume 100 15
Specific Gravity @ 77 F (25 C) 1.80 0.99
Color Black Amber
Viscosity (cps) @ 77 F (25 C) Brookfield 278,000 70
Mixed Viscosity (cps) @ 77 F (25 C) Brookfield 42,500
Work Time, 1 lb. mass @ 77 F (25 C) 3 0.5 hours
Demold Time @ 77 F (25 C) 16 24 hours
Cure Time @ 77 F (25 C) 3 5 days
Properties above are typical and not for specifications.
EPOXY RESIN SYSTEMS
Dedicated to QUALITY, SERVICE, SAFETY, and INNOVATION
TC-4485 A/B Page 2 of 2 Date: 12/18/2015
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
NON-WARRANTY "Except for a warranty that materials substantially comply with the data presented in Manufacturer's latest bulletin describing the product (the basis for this substantial
compliance is to be determined by the standard quality control tests generally performed by Manufacturer), all materials are sold "AS IS" and without any warranty express or implied as
to merchantability, fitness for a particular purpose, patent, trademark or copyright infringement, or as to any other matter. In no event shall Manufacturer's liability for damages exceed
Manufacturer's sale price of the particular quantity with respect to which damages are claimed."
Quality Management
System Registered
to ISO 9001:2008
STORAGE:
Store at ambient temperatures, 65-80 F (18-27 C). Unopened containers will have a shelf life of 12 months from date of shipment
when properly stored at recommended temperatures. Purge opened containers with dry nitrogen before re-sealing.
PACKAGING Part A Part B Cubic Inches per Kit
5-Gallon Kits 60 lbs. 5 lbs. 852
SAFETY PRECAUTIONS :
Use in a well-ventilated area. Avoid contact with skin using protective gloves and protective clothing. Repeated or prolonged contact
on the skin may cause an allergic reaction. Eye protection is extremely important. Always use approved safety glasses or goggles
when handling this product.
IF CONTACT OCCURS :
Skin: Immediately wash with soap and water. Remove contaminated clothing and launder before reuse. It is not recommended
to remove resin from skin with solvents. Solvents only increase contact and dry skin. Seek qualified medical attention if
allergic reactions occur.
Eyes: Immediately flush with water for at least 15 minutes. Call a physician.
Ingestion: If swallowed, call a physician immediately. Remove stomach contents by gastric suction or induce vomiting only as
directed by medical personnel. Never give anything by mouth to an unconscious person.
Refer to the Material Safety Data Sheet before using this product.
TC-4485 Part A SDS TC-4485 Part B SDS
by | Sep 27, 2025
TC-1614 A/B Page 1 of 3 Date: 09/29/2020
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
www.bjbenterprises.com
TC-1614 A/B
EPOXY PENETRATING
SEALING AND COATING RESIN SYSTEM
TC-1614 A/B is an unfilled, low viscosity epoxy resin system. It is designed to seal porous to semi-porous substrates developing
remarkable strength. TC-1614 A/B also has exceptional adhesive characteristics and is capable of high temperatures.
Easy to use and apply Withstands temperatures up to 350 F (177 C)
Penetrates and seals porous surfaces with excellent adhesion Can be pigmented for color enhancement
Works great for sealing 3D Printed parts Recommended by several 3D Printer Manufacturers
PHYSICAL PROPERTIES TEST METHOD TEST RESULTS
Hardness, Shore D ASTM D2240 85 2
Density (g/cc) ASTM D792 1.14
Cubic Inches per Pound N/A 25.1
Color/Appearance Visual Yellow Opaque
Tensile Strength (psi) ASTM D638 9,500
Tensile Modulus (psi) ASTM D638 320,000
Elongation (%) ASTM D638 5
Flexural Strength (psi) ASTM D790 12,600
Flexural Modulus (psi) ASTM D790 380,000
Shrinkage (in/in) linear 12 x x 0.008
Izod Impact, notched (ft-lb/in) ASTM D256 0.44
Reported physical properties based on elevated temperature cured test specimens.
HANDLING PROPERTIES Part A Part B
Mix Ratio by weight 100 20
Mix Ratio by volume 100 23
Specific Gravity @ 77 F (25 C) 1.13 0.98
Color Colorless Amber
Viscosity (cps) @ 77 F (25 C) Brookfield 550 250
Mixed Viscosity (cps) @ 77 F (25 C) Brookfield 600
Work Time, 100g mass @ 77 F (25 C) 2 hours
Tack Free
10 12 hours @ 77 F (25 C)
5 hours @ 120 F (48.9 C)
Properties above are typical and not for specifications.
*Application Procedures see page 3
EPOXY RESIN SYSTEMS
Dedicated to QUALITY, SERVICE, SAFETY, and INNOVATION
An ISO-9001 Certified company
TC-1614 A/B Page 3 of 3 Date: 09/29/2020
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
NON-WARRANTY “Except for a warranty that materials substantially comply with the data presented in Manufacturer’s latest bulletin describing the product (the basis for this substantial
compliance is to be determined by the standard quality control tests generally performed by Manufacturer), all materials are sold “AS IS” and without any warranty express or implied as
to merchantability, fitness for a particular purpose, patent, trademark or copyright infringement, or as to any other matter. In no event shall Manufacturer’s liability for damages exceed
Manufacturer’s sale price of the particular quantity with respect to which damages are claimed.”
POST CURING:
All physical property results are based upon post-curing this system. The following procedure provides the best results:
150 F (66 C) for 1.5 to 2 hours
250 F (121 C) for 2 hours
300 F (149 C) for 1 hour
350 F (177 C) for 1 hour
Allow to cool in the oven. This procedure provides further stabilization and eliminates possible thermal shocks for cavity tools that are
temporarily clamped together for curing purposes.
STORAGE:
Store at ambient temperatures, 65-80 F (18-27 C). Unopened containers will have a shelf life of 12 months from date of shipment
when properly stored at recommended temperatures. Purge opened containers with dry nitrogen before re-sealing.
PACKAGING Part A Part B
Cubic Inches
per Kit
Quart Kits 2 lbs. 7 oz. 61
Gallon Kits 9 lbs. 1.8 lbs. 271
5-Gallon Kits 40 lbs. 8 lbs. 1,205
SAFETY PRECAUTIONS :
Use in a well-ventilated area. Avoid contact with skin using protective gloves and protective clothing. Repeated or prolonged contact
on the skin may cause an allergic reaction. Eye protection is extremely important. Always use approved safety glasses or goggles
when handling this product.
IF CONTACT OCCURS :
Skin: Immediately wash with soap and water. Remove contaminated clothing and launder before reuse. It is not recommended
to remove resin from skin with solvents. Solvents only increase contact and dry skin. Seek qualified medical attention if
allergic reactions occur.
Eyes: Immediately flush with water for at least 15 minutes. Call a physician.
Ingestion: If swallowed, call a physician immediately. Remove stomach contents by gastric suction or induce vomiting only as
directed by medical personnel. Never give anything by mouth to an unconscious person.
Refer to the Material Safety Data Sheet before using this product.
WARNING: This product can expose you to chemicals including Ethylbenzene and 4,4 -Isopropylidenediphenol, which are known to
the State of California to cause cancer, birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
TC-1614 A/B Page 3 of 3 Date: 09/29/2020
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
NON-WARRANTY “Except for a warranty that materials substantially comply with the data presented in Manufacturer’s latest bulletin describing the product (the basis for this substantial
compliance is to be determined by the standard quality control tests generally performed by Manufacturer), all materials are sold “AS IS” and without any warranty express or implied as
to merchantability, fitness for a particular purpose, patent, trademark or copyright infringement, or as to any other matter. In no event shall Manufacturer’s liability for damages exceed
Manufacturer’s sale price of the particular quantity with respect to which damages are claimed.”
Product Application Procedure for 3D Printed Parts
Material: TC-1614 Epoxy
Purpose of Procedure: To impregnate rigid, porous 3D Printed Parts with epoxy. Infusing epoxy into the surface is a
beneficial procedure to increase strength, improve handling qualities and in some parts, improve aesthetics. Some
systems will absorb more material than others.
Procedure:
Pre-warm A&B material in separate containers to 90 -100 F maximum (32 -37 C max) in a temperature
controlled industrial oven. This will help to lower the viscosity and increase the absorption rate of epoxy into
the part (never use a household oven that may be in contact with food).
You can also pre-warm the 3D printed part to aid in epoxy infiltration. 100 -120 F (37 -49 C) is a good range
but refer to your 3D printed material recommendations for heat resistance in an effort to avoid distortion.
Place a small 3D Printed Part into a self-sealing (zipper lock) plastic bag and fill with an appropriate amount
of epoxy. A bag that is too large will require more volumetric amounts of epoxy. Squeeze out as much of the
extra air in the bag to assure part is fully submerged and coated with epoxy then seal bag.
Allow the part to soak in the epoxy for roughly 20-25 minutes. A recommended optional procedure would be
to place bag with soaking 3D Printed part into 100 -120 F (37 -49 C) oven in a leak-proof, metal container,
and allow to soak for 15-20 minutes. Check part at 5 minute intervals to monitor viscosity levels and for any
exothermic reaction. Larger batches of mixed epoxy will have a shorter reaction time.
Once part has soaked for allotted time, pull part out of bag and drain excess epoxy off of part.
For larger parts, mix enough A&B together so you have sufficient material to brush an even coat over the part.
Continue brushing drips and runs to keep part coated for 20-30 minutes. Then drain off excess epoxy and
wipe down surface with clean, dry paper towels. Avoid using any solvents since it will affect the curing
properties.
*Note that mixing a large mass of epoxy can produce an increase in chemical reaction shortening work time
and increasing exotherm (heat) as it sits. Do not leave a large, concentrated mass of epoxy in a container
unattended. After soaking the part, it may be best to split up a large batch (over 200-300g) by draining the
bag into 2-3 separate small containers and allow to harden.
Hang part with wire over a cup or bucket to allow continued drainage of excess epoxy. Wipe off any areas of
pooled epoxy with a gloved finger or brush. Monitor any sags or drips for the next hour or until epoxy has
gelled.
You can expedite curing of the epoxy in an oven at 100 -120 F (37 -49 C) and promote better physical
properties of the finished material. You can also allow the epoxy to cure at room temperature but an elevated
post cure will achieve the best results.
by | Sep 27, 2025
EPOff RESTw SySTEMS
” I) t: rl i c u t etl t o QU
A L I TY, S ti R r l c jt.
s.,l t; liI’t” a n
by | Sep 27, 2025
TC-1570 A/B Page 1 of 2 Date: 02/13/2020
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-8929
www.bjbenterprises.com
TC-1570 A/B
WHITE EPOXY SURFACE COAT
TC-1570 A/B is a general-purpose white epoxy surface coat that can be used in conjunction with epoxy or polyurethane resin
systems. TC-1570 A/B is noted for its ease of application and its ability to hang on vertical surfaces without sag or runoff.
PHYSICAL PROPERTIES TEST METHOD RESULTS
Hardness, Shore D ASTM D2240 90 2
Density (g/cc) ASTM D792 1.92
Cubic Inches per Pound N/A 13.7
Color/Appearance Visual White Opaque
Flexural Strength (psi) ASTM D790 8,100
Flexural Modulus (psi) ASTM D790 9.5 x 10
5
Heat Deflection Temperature @ 66 psi ASTM D648 220 F (104.4 C)
Heat Deflection Temperature @ 264 psi ASTM D648 217 F (102.8 C)
HANDLING PROPERTIES Part A Part B
Mix Ratio by weight 100 8
Specific Gravity @ 77 F (25 C) 2.1 1.08
Mixed Viscosity (cps) @ 77 F (25 C) Brookfield Brushable
Work Time, 100g mass @ 77 F (25 C) 15 20 minutes
Cure Schedule 8 12 hours
Properties above are typical and not for specifications.
STORAGE:
Store at ambient temperatures, 65-80 F (18-27 C). Unopened containers will have a shelf life of 12 months from date of
shipment when properly stored at recommended temperatures. Purge opened containers with dry nitrogen before re-sealing.
PACKAGING Part A Part B
Square Inches
per Kit
(Coverage @ 1/16 thick)
Quart Kits 3 lbs. 4 oz. 712
Gallon Kits 10 lbs. 13 oz. 2,370
5-Gallon Kits 45 lbs. 3.6 lbs. 10,653
EPOXY RESIN SYSTEMS
Dedicated to QUALITY, SERVICE, SAFETY, and INNOVATION
An ISO-9001 Certified company
TC-1570 A/B Page 2 of 2 Date: 02/13/2020
For more information call BJB Enterprises, Inc. (714) 734-8450 Fax (714) 734-892
NON-WARRANTY “Except for a warranty that materials substantially comply with the data presented in Manufacturer’s latest bulletin describing the product (the basis for this substantial
compliance is to be determined by the standard quality control tests generally performed by Manufacturer), all materials are sold “AS IS” and without any warranty express or implied as
to merchantability, fitness for a particular purpose, patent, trademark or copyright infringement, or as to any other matter. In no event shall Manufacturer’s liability for damages exceed
Manufacturer’s sale price of the particular quantity with respect to which damages are claimed.”
SAFETY PRECAUTIONS :
Use in a well-ventilated area. Avoid contact with skin using protective gloves and protective clothing. Repeated or
prolonged contact on the skin may cause an allergic reaction. Eye protection is extremely important. Always use approved
safety glasses or goggles when handling this product.
IF CONTACT OCCURS :
Skin: Immediately wash with soap and water. Remove contaminated clothing and launder before reuse. It is not
recommended to remove resin from skin with solvents. Solvents only increase contact and dry skin. Seek
qualified medical attention if allergic reactions occur.
Eyes: Immediately flush with water for at least 15 minutes. Call a physician.
Ingestion: If swallowed, call a physician immediately. Remove stomach contents by gastric suction or induce vomiting
only as directed by medical personnel. Never give anything by mouth to an unconscious person.
Refer to the Material Safety Data Sheet before using this product.
WARNING: This product can expose you to chemicals including 4,4 -Isopropylidenediphenol, which are known to
the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to
www.P65Warnings.ca.gov.
TC-1570 Part A SDS TC-1570 Part B SDS
