MATERIAL SAFETY DATA SHEET
ACCORDANCE TO REGULATION (EC) 1907/2006
ACCORDANCE TO REGULATION (EC) 1907/2006 Page 1 of 8
VIP Infusion Flow Green 75
1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY /
UNDERTAKING
PRODUCT NAME: VIP Infusion Flow Green 75
USE OF SUBSTANCE/PREPARATION: High density polyethylene
RECOMMENDED USE:
MANUFACTURER: Umeco Process Materials
12801 Ann Street
Santa Fe Springs, CA 90670
FOR MORE INFORMATION CALL: 562-906-3300
IN CASE OF EMERGENCY CALL: 562-906-3300
2. HAZARDS IDENTIFICATION
INDICATION OF DANGER: This product an inert polyethylene. According to Directives
67/548/EEC and 1999/45/EC, it is not classified as hazardous to humans and the environment.
This product is not considered hazardous by the criteria described in the OSHA Hazard
Communication Standard (29 CFR 1910.1200).
Route of Entry: Skin and eye contact
Target Organs: None
Inhalation: Not a route of exposure under normal handling and usage. Vapors may
cause irritation at molten temperatures.
Skin Contact: Not considered hazardous under normal handling and usage.
Eye Contact: Not considered hazardous. May cause mechanical irritation if film
comes into contact with the eye.
Ingestion: Not a route of exposure. Not considered hazardous.
Carcinogenic Status: Not considered carcinogenic by NTP, IARC, and OSHA
MATERIAL SAFETY DATA SHEET
ACCORDANCE TO REGULATION (EC) 1907/2006
ACCORDANCE TO REGULATION (EC) 1907/2006 Page 2 of 8
3. HAZARD IDENTIFICATIONCOMPOSITION / INFORMATION ON INGREDIENTS
HAZARDOUS COMPONENTS: None – Product is an inert polyethylene and poses no danger in its
current form.
Ingredient Name
CAS # % of Ingredient
Polyethylene 9002-88-4 >95%
Modifiers/Additives N/A <5%
The above product(s) are considered articles according to OSHA Hazard Communication
Standard 29 CFR 1910.1200 and, as such, are exempt from the material safety data sheet
provisions of 29 CFR 1910.1200 (G) (6). These products are considered non-hazardous when used
according to accepted practices for the intended use.
Components are not classified as dangerous according to Directive 1999/45/EC. Quantities of listed
compounds contained in this product are not reportable under the article exemption since they do
not release or otherwise result in exposure of a hazardous chemical under normal conditions of
use. Product is a solid film that requires no preparation and causes no health or environmental
hazards within the meaning of Directive 67/548/EEC.
4. FIRST AID MEASURES
Inhalation: Not an expected route of entry during normal handling and use.
Remove person to fresh air and seek medical attention if adverse
symptoms appear.
Skin Contact: Not an expected route of entry during normal handling and use.
Eye Contact: Not an expected route of entry during normal handling and use.
Ingestion: Obtain immediate medical attention.
Advice to Physicians: Treat symptomatically.
MATERIAL SAFETY DATA SHEET
ACCORDANCE TO REGULATION (EC) 1907/2006
ACCORDANCE TO REGULATION (EC) 1907/2006 Page 3 of 8
5. FIRE FIGHTING MEASURES
FLAMMABLE PROPERTIES
Flash Point (Method Used): >640 F (340 C)
Ignition Temperature: >680 F (360 C)
LEL: N/A
UEL: N/A
Extinguishing Method: Carbon dioxide, dry chemical, foam, water or other agents
as appropriate for materials in surrounding fire.
Special Fire Fighting Procedures: Wear NIOSH/MSHA approved positive pressure self-
contained breathing apparatus and full protective clothing.
Unusual Fire and Explosion Hazards: Products of combustion may include oxides of carbon and
nitrogen.
6. ACCIDENTAL RELEASE MEASURES
No specific measure necessary. Prevent material from entering drains or water courses.
7. HANDLING AND STORAGE
Handling Precautions: Use normal personal hygiene and good housekeeping.
Storage Requirements: Store in a cool (<140 F), dry area, away from sources of ignition.
MATERIAL SAFETY DATA SHEET
ACCORDANCE TO REGULATION (EC) 1907/2006
ACCORDANCE TO REGULATION (EC) 1907/2006 Page 4 of 8
8. EXPOSURE CONTROL / PERSONAL PROTECTION
Engineering Controls: No specific measures necessary.
Environmental Exposure Control: No specific measures necessary.
Respiratory Protection: No specific measures necessary.
Hand Protection: No specific measures necessary.
Eye Protection: No specific measures necessary.
Use safety glasses if necessary.
Skin Protection:
No specific measures necessary.
OCCUPATIONAL EXPOSURE STANDARDS:
INGREDIENT
NAME
Guideline Form of Exposure Concentration
N/A
MATERIAL SAFETY DATA SHEET
ACCORDANCE TO REGULATION (EC) 1907/2006
ACCORDANCE TO REGULATION (EC) 1907/2006 Page 5 of 8
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance: Solid clear plastic net
Physical Status: Solid
Odor: Slight waxy odor
pH: N/A
Vapor Pressure: N/A
Vapor Density: N/A
Boiling Point: N/A
Freezing/Melting Point: 212-275 F (100-135 C)
Solubility: N/A
Spec. Grav./Density: 0.88-0.96 g/cm
3
10. STABILITY AND REACTIVITY
Stability: Normally Stable
Conditions to avoid: Avoid exposure to open flame or temperatures
exceeding recommended processing temperatures.
The maximum temperature to which the film can be
exposed will vary with exposure (dwell) time. Umeco
should be contacted if questions arise concerning
specific processing conditions.
Materials to avoid (Incompatibility): Strong oxidizers, acids, alkalis, halogens, halogenated
hydrocarbons
Hazardous Decomposition Products: Thermal decomposition products may include
acetaldehyde, ketones, acrolein, acetone, acetic acid,
formic acid, formaldehyde.
Hazardous Polymerization: Will not occur
11. TOXICOLOGICAL INFORMATION
Acute Toxicity: Not determined
Chronic Toxicity / Carcinogenicity Effects: Not expected to cause adverse health effects.
Genotoxicity: Not expected to cause mutagenic effects.
Reproductive / Developmental Toxicity: Not expected to cause adverse reproductive effects.
Other Data: N/A
MATERIAL SAFETY DATA SHEET
ACCORDANCE TO REGULATION (EC) 1907/2006
12. ECOLOGICAL INFORMATION
Product is not classified as hazardous according to Directive 1999/45/EC. No relevant studies
identified.
Exotoxicity: No relevant studies identified.
Mobility: No relevant studies identified.
Persistance and degradability: No relevant studies identified
Bioaccumulative Potential: No relevant studies identified.
Other Adverse Effects: N/A
13. DISPOSAL CONSIDERATIONS
Dispose of in compliance with Federal, state and local government regulations. Usually is
considered an inert packaging material that can be recycled, incinerated, or landfilled.
14. TRANSPORT INFORMATION
No special precautions to be aware of under 1907/2006/EC.
US DOT Hazard Class: Not regulated
US DOT ID Number: Not applicable
UN Proper Shipping Name: None
UN Class: None
UN Packaging Group: None
Marine Pollutant: Not applicable
Classification for AIR Transportation (IATA): Consult current IATA regulations prior to
shipping by air.
ACCORDANCE TO REGULATION (EC) 1907/2006 Page 6 of 8
MATERIAL SAFETY DATA SHEET
ACCORDANCE TO REGULATION (EC) 1907/2006
ACCORDANCE TO REGULATION (EC) 1907/2006 Page 7 of 8
15. REGULATORY INFORMATION
Quantities of listed components contained in this product are not reportable under article exemption
according to Directives 67/548/EEC and 1999/45/EC.
Toxic Substance Control Act (TSCA)
TSCA Inventory Status: N/A
Other TSCA Issues: None
SARA Title III/CERCLA
"Reportable Quantities" (RQs) and/or "Threshold Planning Quantities" (TPQs) exist for the
following ingredients.
Ingredient Name
SARA/CERCLA RO (lb) SARA EHS TPO (lb)
No ingredients listed in this section. Section 311 Hazard Class: None. The following ingredients are SARA 313 "Toxic Chemicals". CAS numbers and weight percents
are found in Section 2.
Ingredient Name
Comment
No ingredients listed in this section.
MATERIAL SAFETY DATA SHEET
ACCORDANCE TO REGULATION (EC) 1907/2006
ACCORDANCE TO REGULATION (EC) 1907/2006 Page 8 of 8
State Right-To-Know
In addition to the ingredients found in Section 2, the following are listed for state right-to-know
purposes.
Ingredient Name Weight % Comment
N/A
California Prop. 65 : On This product does not contain any chemicals known to State of California
to cause cancer, birth, or any other reproductive defects.
Additional Regulatory Information:
This product is not intended to be used in any application which places the product in direct
contact with the human body, or in other FDA governed applications, unless specifically
designated otherwise in written material supplied by Umeco to the purchaser.
WHMIS Classification (Canada):
Not a controlled substance. (Considered to be a manufactured article.)
Foreign Inventory Status:
All base monomers and other components are listed on the EINECS Inventory.
16. OTHER INFORMATION
Prepared By:
Engineering and Quality Assurance
Bibliography:
- Directive EEC 67/548 and following adaptations
- Directive 1999/45/EC, as amended
- Directive 76/769/EEC and following amendments
- Directive 2001/58/EC
- EINECS/ELINCS
- 1907/2006/EC
Current Issue Date: 11/30/2012
Previous Issue Date: N/A