Froth-Pak
Foam Sealant* is the complete, all-in-one self-
contained and easily portable kit for professional contractors to
quickly and efficiently fill larger gaps and penetrations sealing
out moisture, dust, allergens and pests while improving energy
efficiency, building resilience and comfort for homeowners.
The new Froth-Pak
Sealant has a GWP reduction of over
99% and contains no ozone depleting chemicals or HFCs
while maintaining the performance attributes professional
contractors expect.
Froth-Pak
Sealant s industry-leading, customizable dispensing
system helps ensure consistent flow rate, on-ratio application
and complete dispensing of product. And unlike one-component
foam, Froth-Pak
Sealant is designed to significantly reduce
curing time. It dispenses, expands and becomes tack-free in
seconds.
Froth-Pak
Sealant can be used safely in a wide range of settings,
reducing the potential for unwelcome dust, pests, moisture, mold,
mildew, allergens and rot.
TABLE 1: Sizes and Theoretical Yields for Froth-Pak
Foam Sealant
Product Theoretical Yield,
(1)
board ft
Kits
Froth-Pak
12 12 (0.03)
Froth-Pak
120 120 (0.28)
Froth-Pak
200 200 (0.46)
Froth-Pak
620 620 (1.46)
Refillable Cylinders
Froth-Pak
17 (gal) 2060 (4.85)
Froth-Pak
27 (gal) 3240 (7.65)
Froth-Pak
60 (gal) 6860 (16.2)
Froth-Pak
120 (gal) 15430 (36.4)
Froth-Pak
350 (gal) 43890 (103.6)
1
The theoretical yield has become an industry standard for identifying certain sizes of two-
component kits. Theoretical yield calculations are performed in perfect laboratory conditions,
without taking into account the loss of blowing agent or the variations in application methods
and types.
* Froth-Pak
Foam Sealant is a former product of The Dow Chemical Company.
** Actual cure time will depend on temperature, foam thickness, the specific nozzle used, etc
Ease of Use
Froth-Pak
Sealant is:
Chemically cured foam with reduced curing time
Tack free in 30 seconds and cures in minutes**
Available in refillable cylinders or disposable kits
Useful for multiple applications including roof and wall
junctions; wall and attic penetrations; basements and
crawlspaces; electrical, mechanical and plumbing
penetrations and other gaps, cracks or crevices in the
building envelope
Complete and portable two-component, quick-cure
polyurethane foam kit that fills cavities, penetrations, cracks
and expansion joints
New anti-crossover nozzle and ergonomic dispensing system
results in minimal to no overspray helps ensure consistent
flow rate, on-ratio application and complete dispensing of
product.
Contains no ozone depleting chemicals or HFCs
Blocks air infiltration and helps to meet air change per hour
(ACH) code requirements and reduce building energy costs
Reduces the potential for moisture, mold, mildew, allergens
and rot
One-hour occupant re-entry with proper ventilation after
dispensing
Faster 30 second cure time
Bonds to wood, rigid foam, masonry, metal, drywall and more
Formulation and dispensing systems are patent pending
Froth-Pak
Foam Sealant
Two-Component, Quick Cure, Professional Sealant Kit
HFC-Free, Low GWP, No Ozone Depleting Chemicals
Features and Benefits
Product Information Sheet
TABLE 2: Typical Physical Properties of Froth-Pak
Foam Sealant
These properties are typical but do not constitute specifications.
Property and Test Method Value
Flame Spread/Smoke Developed,
(2)
ASTM E84/UL 723 @ 4 wide by 2 thick 25 / 450
Nominal Density, ASTM D1622, lb/ft
3
1.75
Thermal Resistance
(3)
per inch, ASTM C518, ft
2
h F/Btu, R-value, min.
Initial
Aged LTTR measured at 2 thick
6.7
9.1
Water Vapor Permeance, ASTM E96, perm @ 1 thick 5.4
Water Absorption, ASTM D2842, % by volume 3.4
Air Permeability, ASTM E2178 is 0.0088 L/sec-m
2
@ 75Pa 0
Dimensional Stability, ASTM D2126, % volume change
158 F/100% RH @ 2 wks
-4 F/amb RH @ 2 wks
14
0.3
Compressive Strength, ASTM D1621, lb/in
2
, parallel 16.3
Flexural Strength, ASTM C203, lb/in
2
, parallel 20.1
Tensile Strength, ASTM D1623, lb/in
2
, parallel 29
Shear Strength, ASTM C273, lb/in
2
, parallel 13.8
Maximum Service Temperature, F 240
1
Tested at 2 thickness, full coverage.
2
This numerical flame spread rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
3
R means resistance to heat flow. The higher the R-value, the greater the insulating power.
Values may differ for Froth Pak 12.0 and specialty kits. Contact a DuPont representative for more information.
Properties
Review all instructions and Safety Data Sheet (SDS) before use. Please contact DuPont at 1-866-583-2583 when additional guidance
is required for writing specifications that include this product.
Testing
Applicable Standards ASTM International
C518 Standard Test Method for Steady-State Thermal
Transmission Properties by Means of the Heat Flow Meter
Apparatus
C273 Standard Test Method for Shear Properties of Sandwich
Core Materials
D1621 Standard Test Method for
Compressive Properties of Rigid Cellular Plastics
D1622 Standard Test Method for Apparent Density of Rigid
Cellular Plastics
D1623 Standard Test Method for Tensile and Tensile Adhesion
Properties of Rigid Cellular Plastics
D2126 Standard Test Method for Response of Rigid Cellular
Plastics to Thermal and Humid Aging
D2842 Standard Test Method for Water Absorption of
Rigid Cellular Plastics
E96 Standard Test Methods for Water Vapor Transmission
of Materials
C203 Standard Test Methods for Breaking Load and
Flexural Properties of Block-Type Thermal Insulation
Notice
Froth-Pak
Foam Sealant complies with the following codes:
CCMC 13447-L
Underwriters Laboratories, Inc. (UL) Classified, see Classification
Certificate R13655
Contact your DuPont sales representative or local authorities
for state and local building code requirements and related
acceptances.
Available Sizes
Froth-Pak
Sealant is typically sold as a complete kit that
includes pressurized A and B cylinders, Insta-Flo
a dispensing
gun/hose assembly and accessories. Froth-Pak
Sealant is also
available in refillable, returnable tanks for applications requiring
a large amount of foam, such as poultry houses. See Table 1 for
size and yield information.
Precautionary Statements
Froth-Pak
Foam will adhere to most surfaces and skin. Avoid
ALL skin contact. Wear gloves and protective clothing. Cured
foam is difficult to remove. Cured foam must be mechanically
removed or allowed to wear off in time.
WARNING: CURED FOAM IS COMBUSTIBLE AND WILL BURN
IF EXPOSED TO OPEN FLAME OR SPARKS FROM HIGH ENERGY
SOURCES. These products should not be sprayed where the
foam may come into contact with hot surfaces, such as
heaters, furnaces, fireplaces, or recessed lighting fixtures.
The foam should NOT be exposed to temperatures over
240 F (116 C).
Avoid overfilling restricted spaces. The reaction of these
chemicals causes expansion and may exert enough force to
cause an uncontrolled stream of foam, spraying the work area
and possibly the operator.
Froth-Pak
contains isocyanate, blowing agent and polyol.
Read all instructions and (M)SDS carefully before use. Wear
protective clothing and cover all skin (including long sleeves),
gloves, goggles or safety glasses, and proper respiratory
protection.
Do not breathe vapor or mist. Use only with adequate
ventilation.
Isocyanate is irritating to the eyes, skin and respiratory system,
and may cause sensitization by inhalation or skin contact.
Contents are under pressure.
Personal Protective Equipment (PPE)
Personal protective equipment (PPE) used during the handling
of Froth-Pak
foam products must at a minimum include:
Protective clothing or impermeable coveralls, such as a
Tyvek
coverall suit, including long sleeves (no skin should
be exposed)
Chemical-resistant gloves that are coated with nitrile, butyl
rubber, neoprene or PVC
Goggles or safety glasses, unless using a full-face respirator
Proper respiratory protection, see section 2.2
PPE should be worn by:
Applicator
Anyone assisting applicator
Other workers in the room within 25 ft of the applicator
Anyone entering the spray area less than one hour post
spraying with proper ventilation
If PPE is contaminated during application, properly discard and
replace immediately. Do not consume or store food or tobacco in
the work area. Make sure to wash your hands and face before
eating or smoking after application.
Safe Handling
WARNING: For Professional Use Only The Froth-Pak
cylinders contain isocyanate, blowing agent and polyols under pressure.
Read and follow product manual and the Safety Data Sheets (SDSs) (formerly MSDSs or Material Safety Data Sheets) carefully
before use. The safety precautions and personal protective equipment indicated below are designed to protect the user and allow
for the safe use and handling of the spray system. Follow all applicable federal, state, local and employer regulations..
Installation
Use Conditions
Complete operating instructions are provided with each
Froth-Pak
Foam Sealant purchase. Read all information
and cautions before application.
Froth-Pak
Foam will adhere to most surfaces and skin.
Avoid ALL skin contact. Wear gloves and protective clothing.
Check with local codes prior to use. If used in an exterior
setting, a coating must be applied for ultraviolet (UV)
protection.
Application
Avoid overfilling restricted spaces. The reaction of these
chemicals causes expansion and may exert enough force to
cause an uncontrolled stream of foam, spraying the work area
and possibly the operator.
One-hour occupant re-entry with proper ventilation after
dispensing.
Curing
Cure time will depend on temperature, foam thickness,
the specific nozzle used, etc.
Cured foam is difficult to remove. Cured foam must be
mechanically removed or allowed to wear off in time.
Equipment
Dispensing gun/hose assembly and accessories included in kit.
* See full ventilation guidelines at building.dupont.com.
For more information visit us at
frothpak.com/sealant
or call 1-833-338-7668
NOTICE: No freedom from any patent owned by DuPont or others is to be inferred. Because use conditions and applicable laws may differ from one location to another and may change with time, Customer is responsible for
determining whether products and the information in this document are appropriate for Customer s use and for ensuring that Customer s workplace and disposal practices are in compliance with applicable laws and other
government enactments. The product shown in this literature may not be available for sale and/or available in all geographies where DuPont is represented. The claims made may not have been approved for use in all
countries or regions. DuPont assumes no obligation or liability for the information in this document. References to DuPont or the Company mean the DuPont legal entity selling the products to Customer unless otherwise
expressly noted. NO EXPRESS WARRANTIES ARE GIVEN EXCEPT FOR ANY APPLICABLE WRITTEN WARRANTIES SPECIFICALLY PROVIDED BY DUPONT. ALL IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY EXCLUDED. The buyer assumes all risks as to the use of the material. Buyer s exclusive remedy or any claim (including without limitations, negligence, strict
liability, or tort) shall be limited to the refund of the purchase price of the material. Failure to strictly adhere to any recommended procedures shall release DuPont Specialty Products USA, LLC or its affiliates, of all liability
with respect to the materials or the use thereof. The information herein is not intended for use by non-professional designers, applicators or other persons who do not purchase or utilize this product in the normal course
of their business.
DuPont Polyurethane Foam Insulation and Sealants
CAUTION: When cured, these products are combustible and will burn if exposed to open flame or sparks from high-energy sources. Do not expose to temperatures above 240 F. For more information, consult (M)SDS call
DuPont at 1-866-583-2583 or contact your local building inspector. In an emergency, call 1-866-583-2583. When air sealing buildings, ensure that combustion appliances, such as furnaces, water heaters, wood burning stoves,
gas stoves and gas dryers are properly vented to the outside. See website: http://www.epa.gov/iaq/homes/hip-ventilation.html. In Canada visit: http://archive.nrc-cnrc.gc.ca/eng/ibp/irc/bsi/83-house-ventilation.html.
Froth-Pak
Spray Polyurethane Foam contains isocyanate, blowing agent and polyol. Read all instructions and (M)SDS carefully before use. Wear protective clothing and cover all skin (including long sleeves), gloves, goggles
or safety glasses, and proper respiratory protection. Do not breathe vapor or mist. Use only with adequate ventilation. It is recommended that applicators and those working in the spray area wear respiratory protection.
Increased ventilation significantly reduces the potential for isocyanate exposure; however, supplied air or an approved air-purifying respirator equipped with an organic vapor sorbent and a particulate filter may still be
required to maintain exposure levels below ACGIH, OSHA, WEEL or other applicable limits. For situations where the atmospheric levels may exceed the level for which an air-purifying respirator is effective, use a
positive-pressure, air-supplying respirator (air line or self-contained breathing apparatus). Spraying large amounts of foam indoors may require the use of a positive pressure, air-supplying respirator. Contents under pressure.
Building and/or construction practices unrelated to insulation could greatly affect moisture and the potential for mold formation. No material supplier including DuPont can give assurance that mold will not develop in any
specific system.
DuPont
, the DuPont Oval Logo, and all trademarks and service marks denoted with ,
SM
or are
owned by affiliates of DuPont de Nemours, Inc. unless otherwise noted. 2021 DuPont. 43-D100068-enNA 0521 CDP
IF ATMOSPHERIC LEVELS EXCEED THE LEVEL FOR WHICH
AN AIR-PURIFYING RESPIRATOR IS EFFECTIVE A positive-
pressure, air-supplying respirator such as an air line or
self-contained breathing apparatus.
NIOSH-approved full-face or half-mask airpurifying respirator
with an organic vapor sorbent and a P100 particulate filter
For situations where the atmospheric levels may exceed
the level for which an air-purifying respirator is effective at
maintaining exposure levels below ACGIH, OSHA, WEEL or
other applicable limits, use a positive-pressure, air-supplying
respirator (air line or self-contained breathing apparatus) or
supplied air.
Change out respirator cartridges according to your employer s
change-out schedule (typically 8 hours or end of shift).
The spray foam applicator and anyone within 25 feet of the
applicator, must use approved respiratory protection.
If there is ever a doubt as to the potential limits for worker
exposure, DuPont always recommends a positive-pressure,
air-supplying respirator such as an air line or self-contained
breathing apparatus.
See the Product Manual for details
Disposal
Dispose of any residual DuPont
product, coated debris, or
solvent in accordance with applicable federal, state, and local
government regulations.