123M05523_SDS.pdf

Material Safety Data Sheet

Copyright, 2012, 3M Company All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: 3M Scotch-Brite Products, Surface Conditioning, AVFN: Sheets, Rolls, Belts, Scrim
Belts, Discs, Roloc TN, TP, TR, TS, TSM
MANUFACTURER: 3M
DIVISION: Abrasive Systems Division
ADDRESS: 3M Center, St. Paul, MN 55144-1000
EMERGENCY PHONE: 1 -800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 11/08/12
Supercedes Date: 11/08/12
Document Group:05-5844-5
Product Use:
Intended Use: Abrasive Product
SECTION 2: INGREDIENTS
Ingredient C.A.S. No. % by Wt
Aluminum Oxide Mineral 1344-28-1 25 -50
Titanium Dioxide 13463-67-7 0.5 -2.5
Lubricant Trade Secret 0.45 -1
Cured Resin Mixture 25 -40
Nylon Fiber Mixture 10 -20
Nylon Scrim Mixture 5 -10
Poly(Vinyl Chloride) 9002-86-2 0.5 -1.7
Hookit Backing Mixture 0 -5
Attachment Button Mixture 0 -5
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Odor, Color, Grade: Solid Abrasive Product
General Physical Form: Solid

MATERIAL SAFETY DATA SHEET 3M Scotch-Brite Products, Surface Conditioning, AVFN: Sheets, Rolls, Belts, Scrim Belts,
Discs, Roloc TN, TP, TR, TS, TSM 11/08/12
_________________________________________________________________________________________________
Page 2of 8
Immediate health, physical, and environmental hazards: This document covers only the 3M product. For complete assessment,
when determining the degree of hazard, the material being abraded must also be considered.
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:
Mechanical eye irritation: Signs/symptoms may include pain, redness, tearing and corneal abrasion.
Dust created by cutting, grinding, sanding, or machining may cause eye irritation. Signs/symptoms may include redness, swelling,
pain, tearing, and blurred or hazy vision.
Skin Contact:
Mechanical Skinirritation: Signs/symptoms may include abrasion, redness, pain, and itching.
Inhalation:
Dust from cutting, grinding, sanding or machining may cause irritation of the respiratory system. Signs/symptoms may include cough,
sneezing, nasal discharge, headache, hoarseness, and nose and throat pain.
Prolonged or repeated exposure may cause:
Pneumoconiosis: Sign/symptoms may include persistent cough, breathlessness, chest pain, increased amounts of sputum, and changes
in lung function tests.
Ingestion:
No health effects are expected.
This product contains titanium dioxide. Cancer of the lungs has been associated with titanium dioxide. No exposure to titanium
dioxide is anticipated during normal intended use of 3M Coated Abrasives, Surface Conditioning, and Ceramic Grain Products. No
detectable respirable titanium dioxide was found when simulated grinding air sampling studies were conducted on analogous coated
abrasive and surface conditioning constructions that contained similar to or greater concentrations of titanium dioxide. No detectable
respirable titanium dioxide was noted when air sampling studies were conducted on processing ceramic grains containing similar to or
greater concentrations of titanium dioxide. Therefore, the health effects associated with titanium dioxide are not expected during the
intended use of this product.
IngredientC.A.S. No. Class Description Regulation
Titanium Dioxide 13463-67-7 Grp. 2B: Possible human carc.International Agency for Research on Cancer
SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: Flush eyes with large amounts of water.If signs/symptoms persist, get medical attention.
Skin Contact: Wash affected area with soap and water. If signs/symptoms develop, get medical attention.
Inhalation: Remove person to fresh air. If signs/symptoms develop, get medical attention.
If Swallowed: No need for first aid is anticipated.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES

MATERIAL SAFETY DATA SHEET 3M Scotch-Brite Products, Surface Conditioning, AVFN: Sheets, Rolls, Belts, Scrim Belts,
Discs, Roloc TN, TP, TR, TS, TSM 11/08/12
_________________________________________________________________________________________________
Page 3of 8
Autoignition temperature Not Applicable
Flash Point Not Applicable
Flammable Limits(LEL) Not Applicable
Flammable Limits(UEL) Not Applicable
5.2 EXTINGUISHING MEDIA
Ordinary combustible material. Use fire extinguishers with class A extinguishing agents (e.g., water, foam).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus
(SCBA).
Unusual Fire and Explosion Hazards: None inherent in this product.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and therm al decomposition
information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
6.1. Personal precautions, protective equipment and emergency procedures
Not applicable.
6.2. Environmental precautions
Not applicable.
Clean-up methods
Not applicable.
In the event of a release of this material, the user should determine if the release qualifies as reportable according to
local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
For industrial or professional use only. Avoid breathing of dust created by sanding, grinding or machining. Avoid eye contact with
dust or airborne particles. Damaged product can break apart during use and cause serious injury to face or eyes. Check product for
damage such as cracks or nicks prior to use. Replace if damaged. Always wear eye and face protection when working at sanding or
grinding operations or when near such operations. Sparks and particles flying from the product during sanding or grinding can cause
injury and fire.
7.2 STORAGE
Store in a cool, dry place.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
Provide ventilation adequate to control dust concentrations belowrecommended exposure limits and/or control dust. Warning:

MATERIAL SAFETY DATA SHEET 3M Scotch-Brite Products, Surface Conditioning, AVFN: Sheets, Rolls, Belts, Scrim Belts,
Discs, Roloc TN, TP, TR, TS, TSM 11/08/12
_________________________________________________________________________________________________
Page 4of 8
Excessive operating speed or generation of extreme heat may result in harmful emissions. Use local exhaust ventilation. Provide
appropriate local exhaust ventilation for sanding, grinding or machining. Use general dilution ventilation and/or local exhaust
ventilation to control airborne exposures to belowOccupational Exposure Limits and/or control dust, fume, or airborne particles. If
ventilation is not adequate, use respiratory protection equipment.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact. To minimize the risk of injury to face and eyes, always wear eye and face protection when working at sanding or
grinding operations or when near such operations.
The following eye protection(s) are recommended: Safety Glasses with side shields
.
8.2.2 Skin Protection
Avoid skin contact. Wear appropriate gloves to minimize risk of injuryto skin from contact with dust or physical abrasion from
grinding or sanding.
8.2.3 Respiratory Protection
Avoid breathing of dust created by sanding, grinding or machining. Assess exposure concentrations of all materials involved in the
work process. Consider material being abraded when determining the appropriate respiratory protection. Select and use appropriate
respirators to prevent inhalation overexposure.
An exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part of a full
respiratory protection program. Based on the results of the exposure assessment, select from the following respirator type(s) to reduce
inhalation exposure:
Half facepiece or full facepiece air-purifying respirator suitable for particulates
For questions about suitability for a specific application, consult with your respirator manufacturer.
8.2.4 Prevention of Swallowing
Not an expected route of exposure. Wash hands after handling and before eating.
8.3 EXPOSURE GUIDELINES
IngredientAuthorityType Limit Additional Information
Aluminum Oxide Mineral CMRG TWA 1 fiber/cc
Aluminum Oxide Mineral OSHA TWA, respirable
fraction
5 mg/m3
Aluminum Oxide Mineral OSHA TWA, as total dust15 mg/m3
Titanium Dioxide ACGIH TWA 10 mg/m3
Titanium Dioxide CMRG TWA, as respirable
dust
5 mg/m3
Titanium Dioxide OSHA TWA, as total dust15 mg/m3
SOURCE OF EXPOSURE LIMIT DATA:
ACGIH: American Conference of Governmental Industrial Hygienists
CMRG: Chemical Manufacturer Recommended Guideline
OSHA: Occupational Safety and Health Administration
AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

10.2 Materials to avoid
None known
Hazardous Polymerization: Hazardous polymerization will not occur.
Hazardous Decomposition or By-Products
Substance Condition
Carbon monoxide During Combustion
Carbon dioxide During Combustion

Hazardous Decomposition: Under recommended usage conditions, hazardous decomposition products are not expected. Hazardous
decomposition products may occur as a result of oxidation, heating, or reaction with another material.

SECTION 11: TOXICOLOGICAL INFORMATION
Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION

EPA Hazardous Waste Number (RCRA):Not regulated
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
Not regulated per U.S. DOT, IATA or IMO.
These transportation classifications are provided as a customer service. As the shipper YOU remain responsible for
complying with all applicable laws and regulations, including proper transportation classification and packaging.3M
transportation classifications are based on product formulation, packaging, 3M policies and 3M understanding of applicable
current regulations. 3M does not guarantee the accuracy of this classification information. This information applies only to
transportation classification and notthe packaging, labeling, or marking requirements.The original 3Mpackage is certified
for U.S. ground shipment only. If you are shipping by air or ocean, the package may not meet applicable regulatory
requirements.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONS
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard -No Pressure Hazard -No Reactivity Hazard -No Immediate Hazard -Yes Delayed Hazard -Yes
Section 313 Toxic Chemicals subject to the reporting requirements of that section and 40 CFR part 372 (EPCRA):
Ingredient C.A.S. No% by Wt
Aluminum Oxide Mineral 1344-28-1 25 -50
STATE REGULATIONS
Contact 3M for more information.
CHEMICAL INVENTORIES

National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.

RevisionChanges:
Section 8: Exposure guidelines ingredient information was modified.
Section 8: Exposure guideline note was deleted.
Section 1: Product name was modified.
Section 3: Carcinogenicity comment was added.
Section 1: Division name was modified.
Section5: Unusual fire and explosion hazard information was modified.
Section 7: Handling information was modified.
Section 8: Engineering controls information was modified.
Section 13: Waste disposal method information was modified.
Section 8: Respiratory protection -recommended respirators information was modified.
Section 15: WHMIS regulations heading was deleted.
Section 15: WHMIS regulations information was deleted.
Section 8: Respiratory protection -recommended respirators was modified.
Page Heading: Product name was modified.
Sections 3 and 9: Specific physical form information was deleted.
Sections 3 and 9: Specific physical form heading was deleted.
Section 9: Property description for optional properties was modified.
Section 9: Melting point information was modified.
Section 8: Respiratory protection -recommended respirators guide was modified.
Section 8: Respiratory protection -recommended respirators punctuation was deleted.
Section 2: Ingredient table was modified.
Section 15: EPCRA 313 information was added.
Section 15: EPCRA 313 text was added.
Section 8: Exposure guidelines ingredient information was modified.
Section 8: Exposure guideline note was added.
Section 3: Carcinogenicity table was added.
Section 6: Environmental procedures information was modified.
Section 8: Hand protection information was modified.
Copyright was modified.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NOWARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF

3MUSA MSDSs are available at www.3M.com

Our Mission