Able Industrial Products , Inc.
SAFETY DATA SHEET
GHS GT40P printed: 02/12/18 page 1 of 5
1.PRODUCT IDENTIFICATION
TRADE NAME: AMT 440P
OTHER MEANS OF
IDENTIFICATION:
RECOMMENDED USE OF
PRODUCT:
Mold-making Rubber
SUPPLIER S DETAILS: Able Industrial Products
2006 S BAker Ave
Onatrio, Calif. 91761
909-930-1585
Fax 909-930-1587
EMERGENCY CONTACT: CHEMTREC (24 Hours):1-800-424-9300
2.HAZARDS IDENTIFICATION
GHS CLASSIFICATION
PHYSICAL HAZARDS Not Classified
HEALTH HAZARDS Not Classified
ENVIRONMENTAL HAZARDS Not Classified
GHS LABEL ELEMENTS
PICTOGRAMS None
SIGNAL WORDS None
HAZARD STATEMENTS None
PRECAUTIONARY STATEMENTS
[PREVENTION] None
[RESPONSE] None
[STORAGE] None
[DISPOSAL] None
3.COMPOSITION AND INFORMATION ON INGREDIENTS
Able Industrial Products , Inc.
SAFETY DATA SHEET
GHS GT40P printed: 02/12/18 page 2 of 5
Substance or Mixture Mixture
Hazardous Ingredients CAS# Percentage (%)
Quartz 14808-60-7 25-35
*Quartz or crystalline silica is considered to be a nuisance dust. All hazards associated with the
substance are only applicable when the substance is in its respirable form. However, crystalline silica is
not expected to be hazardous when compounded into a liquid polymer like its current state in this
product because it is no longer respirable under normal conditions. Therefore, all hazards associated
with respirable quartz are not listed.
4.FIRST AID MEASURES
INGESTION: Seek medical attention; Do NOT induce vomiting.
SKIN CONTACT: Remove contaminated clothing immediately and dispose of safely.
When in contact with the skin, clean with soap and water.
INHALATION: No first aid should be needed. Remove to fresh air.
EYE CONTACT: Immediately flush with COOL water for 15 minutes; Call a
physician if irritation persists.
PROTECTION FOR FIRST-
AIDERS:
A rescuer should wear personal protective equipment, such as
rubber gloves and air-tight goggles
5.FIRE-FIGHTING MEASURES
SUITABLE EXTINGUISHING
MEDIA:
Foam, carbon dioxide, dry chemical
SPECIFIC FIRE HAZARDS: Fire will form hazardous combustion gases of carbon dioxide
(CO2), carbon monoxide (CO), SiO2, and oxides of nitrogen (NOx).
Product contains silicone, which is known to produce
formaldehyde when temperatures reach in excess of 150
o
C.
Formaldehyde is a known skin, eye, and throat irritant as well as a
potential cancer hazard
FIREFIGHTER EQUIPMENT: Wear respirator and all protective coverings.
6.ACCIDENTAL RELEASE MEASURES
PERSONAL PRECATIONS,
PROTECTIVE EQUIPMENT AND
EMERGENCY:
Safety glasses and gloves are suggested to prevent eye and skin
contact. Provide sufficient ventilation.
ENVIRONMENTAL
PRECAUTIONS:
Prevent product from entering drains.
CLEAN UP: Scrape up and disposed of in accordance with appropriate laws
and regulations.
7.HANDLING AND STORAGE
Able Industrial Products , Inc.
SAFETY DATA SHEET
GHS GT40P printed: 02/12/18 page 3 of 5
HANDLING: Wear protective equipment; Avoid contact with skin and eyes.
STORAGE: Keep container tightly closed. Store in a cool, dry place. Keep
away from oxidizing material.
8.EXPOSURE CONTROLS AND PERSONAL PROTECTION
EXPOSURE LIMITS:
Hazardous Ingredient CAS# Limit/Set by
Quartz 14808-60-7 For Respirable Dust – TWA: 0.025mg/m3(ACGIH),
0.3mg/m3(OSHA)
ENGINEERING CONTROLS: None Available
PERSONAL PROTECTIVE
EQUIPMENT:
RESPIRATORY PROTECTION: Not required under normal use
HAND PROTECTION Protective gloves
EYE PROTECTION Wear safety glasses or goggles. Face shield if situation requires
SKIN AND BODY PROTECTION Protective clothing if situation requires
9.PHYSICAL AND CHEMICAL PROPERTIES
PHYSICAL STATE: Flowable Paste
ODOR: No Odor
ODOR THRESHOLD: Not Available
pH: Not Available
MELTING POINT: Not Available
BOILING POINT RANGE: Not Applicable, will decompose before it will boil
FLASH POINT: >205
o
F (Setaflash)
EVAPORATION RATE: Not Available
FLAMMABILITY(solid/gas): Not Available
EXPLOSION LIMITS:
UPPER Not Available
LOWER Not Available
VAPOR PRESSURE: <0.1mbar @ 68
o
F
VAPOR DENSITY: All vapors are denser than air
RELATIVE DENSITY: 1.35 g/mL
SOLUBILITY: Not soluble in water
PARTITION COEFFICIENT: N-
OCTANOL/WATER: Not Available
AUTO-IGNITION TEMPERATURE: Not Available
DECOMPOSITION
TEMPERATURE: >150
o
C
VISCOSITY: 44,200 cP
10.STABILITY AND REACTIVITY
Able Industrial Products , Inc.
SAFETY DATA SHEET
GHS GT40P printed: 02/12/18 page 4 of 5
REACTIVITY: Product is designed to react with a catalyst to initiate
vulcanization.
CHEMICAL STABILITY: Stable in the absence of contamination
HAZARDOUS REACTIONS: None
CONDITIONS TO AVOID: Avoid contact with strong acids, alkalis, and oxidizing agents.
HAZARDOUS DECOMPOSITION
PRODUCTS:
Hazardous combustion gases of carbon dioxide(CO2), carbon
monoxide(CO), SiO2, and oxides of nitrogen (NOx).
Product contains silicone, which is known to produce
formaldehyde when temperatures reach in excess of 150
o
C.
Formaldehyde is a known skin, eye, and throat irritant as well as a
potential cancer hazard
INCOMPATIBILITY: Acids, Alkalis, Oxidizing Agents
11.TOXICOLOGICAL INFORMATION
ACUTE TOXICITY: Oral LD50(Rat): 13,537 mg/kg (calculated from known toxicities)
SKIN CORROSION/IRRITATION: Not Available
EYE DAMAGE/IRRITATION: Not Available
RESPIRATORY OR SKIN
SENSITATION:
Not Available
GERM CELL MUTAGENICITY: Not Available
CARCINOGENICITY: Quartz (CAS 14808-60-7) is listed by the IARC and the NTP to
cause cancer in humans.
REPRODUCTIVE TOXICITY: Not Available
STOST- SINGLE EXPOSURE: Not Available
STOST- REPEATED EXPOSURE: Not Available
ASPIRATION HAZARD: Not Available
12.ECOLOGICAL INFORMATION
ECOTOXICITY: Do not allow to enter soil, waterways or waste water canal. It is
not allowed to be released into biological sewage treatment
plants. Ecological data is not available.
PERSISTENCE/DEGRADABILITY: Not Available
BIOACCUMULATIVE POTENTIAL: Not Available
MOBILITY IN SOIL: Not Available
13.DISPOSAL CONSIDERATIONS
Recycle to process, if possible. Consult your local regional authorities. You may be able to burn in a
chemical incinerator equipped with an afterburner and scrubber system. Observe all federal, state and local
regulations when disposing of the substance.
14.TRANSPORT INFORMATION
UN/NA Number: Not Regulated
DOT SHIPPING NAME: Not Regulated
DOT HAZARD CLASS: Not Regulated
IMDG P.S.N.: Not Regulated
Able Industrial Products , Inc.
SAFETY DATA SHEET
GHS GT40P printed: 02/12/18 page 5 of 5
IMDG CLASS: Not Regulated
IMDG PACKING GROUP: Not Regulated
IMDG Marine Pollutant: Not Regulated
IATA – P.S.N.: Not Regulated
IATA – CLASS: Not Regulated
IATA PACKING GROUP: Not Regulated
This product and its ingredients are NOT considered dangerous goods according to the UN Model
Regulations, ADR, RID, and the ADN.
15.REGULATORY INFORMATION
US REGULATIONS
US SARA REPORTING REQUIREMENTS: The components of this product are subject to the reporting
requirements of Section 302, 304, and 313 of Title III of the Superfund Amendments and Reauthorization
Act, and are listed as follows:
Hazardous Ingredient SARA 302
(40 CFR 355,
Appendix A)
SARA 304
(40 CFR Table
302.4)
SARA 313
(40 CFR 372.65)
Quartz, Amorphous Silica No No No
U.S. SARA THRESHOLD PLANNING QUANTITY: There are no specific Threshold Planning Quantities for
the components of this product. The default Federal MSDS submission and inventory requirement filing
threshold of 10,000 lbs(4,540 kg) therefore applies, per 40 CFR 370.20
U.S. CERCLA REPORTABLE QUANTITY (RQ): None
SARA 311/312(40 CFR 370) HAZARDS: Acute: No, Chronic: No, Fire: No, Pressure: No
CALIFORNIA, (PROPOSITION 65): Quartz, Crystalline silica
TSCA INVENTORY STATUS: These materials or all of their contents are listed on the Toxic Substances
Control Act (TSCA).
16. OTHER INFORMATION
HMIS Rating: Health-1, Fire-0, Reactive-0
This product contains crystalline silica which is hazardous if it is inhaled. However, in this product, the silica is
wetted out with various polyorganosiloxanes to where it is no longer in powder form, meaning it is incapable of
becoming airborne under normal use conditions. Because the product is a mixture, the majority of the data
used was transferred from the safety data sheets of the product s hazardous ingredients, whose manufacturer
identity we wish to remain anonymous for competitive reasons.
We believe the above information is correct as of the date of this MSDS. However, as this information and the
conditions under which the product are used are beyond the control of GT PRODUCTS, INC., it is the user’s
obligation to determine the conditions for the safe use of the product. No warranty, expressed or implied, is
hereby made.
Date Created/Revised: 2/12/18 Made By: Daniel Shaw