PRODUCT PROPERTIES
All time calculations are based on temperatures of 77 F, 25 C
Lab tested with Norox 925 MEKP
Viscosity, #2 spindle, RVF, 20 rpm 420-480 cps
Thixotropic Index min. 2.5
Gel time @ 2% MEKP 8-11 minutes
Weight per gallon 8.4 lbs/gal (approx)
Coverage per gallon @ 20 mils 80 sq. feet
KEY USES
A high-b uild, easy-s and coating designed as a
topcoat for cured polyester,
polyurethane and lacquer clear or
color coats. You will get a superior
finish,
add quality and save time and labor wit
h Duratec Hi-G loss Coating.
FEATURES
EASY TO APPLY
Sprayable and quick building, to
10-15 mils, 250-375 microns
thickness.
DURATEC CLEAR
HI-GLOSS COATING
PRODUCT # 904- 040
S
AFETY & HANDLING
Duratec Clear Hi-Gl o
ss Coating is extremely flammable. Do not apply near sparks,
open
flames or heat. Keep area ventilated. Do not smoke. Avoid continuous
breathing
of vapor. Duratec Clear Hi-G loss Coating contain s ingredients which
could be harmful if mishan
dled. Co ntact with skin and eyes sh ould be avoided and
necessary
protective equipmen t and clothing should be worn. Individuals should
wash with soap and water before
eating or drinking. All containers sh ould be
properly labeled to prevent accidental ingestion o
r improper d isposal. Individuals
should
reseal any partly used material back in the contain er. Store und er cool, dry
conditions and away
from op en flames and high temperatures.
For more detailed instructions on
storage, please see the MSDS sheet.
Liability/warranty statement: Our products are intended for sale to industrial and commercial customers. We request that
customers inspect and test our products before use and satisfy themselves as to contents and suitability. All claim requests
must be made in writing and are subject to review, including storage temperature verification and retain evaluations. The
exclusive remedy for all proven claims is replacement of our materials. In no event shall we be liable for special, incidental or
consequential damages, including damages caused in transit (exworks terms). Nothing herein shall constitute a warranty,
expressed or implied, including any warranty of merchantability or fitness, nor is protection from any law or patent to be
inferred. All patent and trademark rights are reserved.
DESCRIPTION
909-546-1160
hawkeyesales@hawkeyeind.com
PO BOX 415,
BLOOMINGTON, CA 92316
WWW.HAWKEYEIND.COM
COLOR OPTIONS
Black (602-021)
White (614-02 1)
Composite plugs &
patterns.
Automotive dashboards
Cabinets and furniture
Marine and
aircraft
interiors
Upgrading tooling gelcoats
HIGH GLOSS
Sands
easily and polishes to a
non
-wax, tackfree high gloss
finish.
RESIST
S FISHEYES Unique
additives
reduce the risk of
fi
sheyes and pinhol es during the
s
pray application.
ULTIMATE DURABILITY
Coating produced a hard, durable
surface with fantastic scratch
resistance for high-use areas.
COMPATIBILITY
Compatible with wood, polyester,
vinyl ester, and most epoxy
substrates.
REVISED FEBRUARY 2023
DURATEC CLEAR
HI-GLOSS COATING
APPLIC ATION GUIDE | PR ODUC T #904-040
The following use instructions are broad to address multiple applications. We recommend testing for product
compatability with your process. Please contact our Tech Team at (909) 546-1160 with any questions.
PLEASE NOTE
WWW.HAWKEYEIND.COM 909-546-1160 HAWKEYESALES@HAWK
EYEIND.COM PO BOX 415, BLOOMINGTON, CA 92316Lia Eili Wy wa U Uan Wy s Wa Wemen W O X U S Uod Xc Ws a Ue in Wended Io U sale Wo ind Xs W Uial and comme Ucial c Xs Wome Us. We Ue T Xes W Wha W c Xs Wome Us ins Sec W and Wes W o X U S Uod Xc Ws Ee Io Ue Xse and sa Wis Iy
Whemsel Yes as Wo con Wen Ws and s Xi Wa Eili Wy. All claim Ue T Xes Ws m Xs W Ee made in w Ui Win J and a Ue s X E Mec W Wo Ue Yiew, incl Xdin J s Wo Ua Je Wem Se Ua W X Ue Ye Ui Iica Wion and Ue Wain e Yal Xa Wions. The
e [cl Xsi Ye Uemedy Io U all S Uo Yen claims is Ue Slacemen W o I o X U ma We Uials. In no e Yen W shall we Ee lia Ele Io U s Secial, inciden Wal o U conse T Xen Wial dama Jes, incl Xdin J dama Jes ca Xsed in W Uansi W
e [wo Uks We Ums . No Whin J he Uein shall cons Wi W X We a wa U Uan Wy, e [ S Uessed o U im Slied, incl Xdin J any wa U Uan Wy o I me Uchan Wa Eili Wy o U Ii Wness, no U is S Uo Wec Wion I Uom any law o U Sa Wen W Wo Ee
in Ie U Ued. All Sa Wen W and W Uadema Uk Ui Jh Ws a Ue Uese U Yed.
www.hawkeyeind.com
Prepare & Catalyze
Temperature should be at least 64 F for both the product and the part.
Mix with either a paint shaker or a drill-mounted mixer. A paint stir stick will not be enough for a proper mix.
Catalyze the Duratec at 2.0 % by weight with a full strength MEKP, like Norox 925. Catalyze only an
amount that can be sprayed in 15 minutes, typically about a quart if using a HVLP spray gun. Mix well.
Apply
Duratec Hi-Gloss Coating should be applied by spraying. We recommend HVLP air-assisted spray guns.
Epoxy laminates should be washed with clean water and a heavy duty scrub sponge before and after
sanding. It is not necessary to water wash polyester, vinyl ester, or wood substrates. Abrade the entire
substrate surface with 180-grit to ensure proper mechanical adhesion. Wipe with a clean cloth. Do not use a
tack rag.
A 1.8 mm tip is recommended. Use 34-40 psi air pressure (at the gun). Adjust the needle and fan to provide
the proper spray. Use the lowest pressures possible to minimize orange peel.
The first coat should be a light dust coat. The dust coating does not completely cover the surface. Wait at
least two minutes, and apply another light coat. Continue to make build passes of 4-6 mils, with two minute
intervals, until about 20 mils of product is on the surface.
Allow to cure at room temperature for at least one hour. At that time, cure can be accelerated by putting the
part in a warm room at 120 F
.
Sand
Once the surface is fully cured, sand to remove any texture or orange peel. Use as fine a grit of paper as
is reasonable. Continue sanding with progressively finer grits, up to 1000 grit paper Allow at least eight
hours after sanding before re-coating or before polishing begins.
Compound and polish to high gloss. We recommend Aqua Buff 1000W or 1000F, followed by Aqua Buff
2000.
DURATEC CLEAR
HI-GLOSS COATING
TROUBLESHOOTING | PRODUC T #9
04-040
Problem Cause Solution
Alligatoring
Not enough catalyst used.
Substrate/primer incompatibility or
chemical reaction.
Check for proper catalyst levels.
Expose surface to higher
temperature before spraying when
ambient temp is below 64 F, 18 C.
Product sprayed on cold surface.
Check compatibility of surface of product.
Curing on surface but
not on substrate
Coating sprayed on cold surface
Expose substrate to higher temperture
before spraying.
Dimples (Craters)
Film build up too rapid, solvent
trapped in product.
Increase the number of passes to achieve
desired thickness. Allow for ash o
between passes.
Fisheyes
Substrate contaminated.
Do not use a tack rag . Ensure rag does
not leave contaminant on surface.
Spray in a clean area to minimize airborne
dust, water, waxes, and/or silicones.
Spray with dry fltered air.
Contamination in the air.
Contamination in the line.
Orange Peel
Spray equipment set up incorrectly.
Spray pressure incorrect.
Pot pressure incorrect.
Follow the instructions for equipment
set up.
Set pressure at 34-40 psi.
Set pressure at 10-12 psi.
Pinholes
Porosity
Substrate porosity.
Fill porous areas with product using
squeegee, brush or roller before spraying.
Acetone used as thinner.
Spray pressure too high.
Spray orifce too small.
Reduce pressure to 34-40 psi.
Use larger orifce.
Use slower solvent such as MEK or
Duratec Reducer
Surface not hard
or glossy
Coating not allowed to breathe after sanding
Allow time for solvents to escape before compounding and polishing.
Low reactivity catalyst used / coating under catalyzed.
Catalyze at 2% with full strength MEKP. Do not use 30 percent MEKP or catalyst with less than 8.8 percent active oygen.
See the Liability and Warranty Statement on Page 1