BE769 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 1: IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKING
1.1Product identifier: BE769 – Epoxy Tooling Board
Not a hazardous substance
CAS: Non-applicable
Other means of identification:
Non-applicable
1.2Relevant identified uses of the substance or mixture and uses advised against:
Relevant uses: Non Hazardous Substance . For industrial user only.
Uses advised against: All uses not specified in this section or in section 7.3
1.3Details of the supplier of the safety data sheet:
Base Materials
Base Materials Ltd,20 Ashville Way
LE8 6NU Leicester – Whetstone – United Kingdom
Phone: 0116 286 5073
sales@base-materials.com
https://www.base-materials.com/
1.4Emergency telephone number: Ecostar Environmental – Reference Code: EREF-00111 : Telephone: +44 800
246 1972 (office hours), WhatsApp: +44 7496 228 905 (office hours), 24/7
Service +44 800 246 1274
SECTION 2: HAZARDS IDENTIFICATION
2.1Classification of the substance or mixture:
When milling: Dust will be produced
GB CLP Regulation:
The product is not classified as hazardous according to GB CLP Regulation.
2.2Label elements:
GB CLP Regulation:
None
2.3Other hazards:
Product does not meet PBT/vPvB criteria
SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS
3.1Substance:
Chemical description: Epoxides
Components:
In accordance with Annex II of The REACH etc. (Amendment etc.) (EU Exit) Regulations 2020, the product
contains:
Identification Chemical name/Classification
Concentratio
n
CAS:Non-applicable
Not a hazardous substance
100 %
To obtain more information on the hazards of the substances consult sections 11, 12 and 16.
3.2Mixture:
Non-applicable
Reaction product based on epoxy
SECTION 4: FIRST AID MEASURES
4.1Description of first aid measures:
Consult a doctor in case of discomfort showing the SDS for the product.
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 1/8
BE769 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 4: FIRST AID MEASURES (continued)
By inhalation:
In case of symptoms, move the person affected into fresh air.
By skin contact:
In case of contact it is recommended to clean the affected area thoroughly with water and neutral soap. In case
of changes to the skin (stinging, redness, rashes, blisters, ), seek medical advice with this Safety Data Sheet
By eye contact:
Rinse with water until the product has been eliminated. In case of problems, consult a doctor showing the SDS
for the product.
By ingestion/aspiration:
In case of consumption in large quantities, it is recommended to seek medical assistance.
Dust: Provide fresh air.
4.2Most important symptoms and effects, both acute and delayed:
Acute and delayed effects are indicated in sections 2 and 11.
4.3Indication of any immediate medical attention and special treatment needed:
Non-applicable
SECTION 5: FIREFIGHTING MEASURES
5.1Extinguishing media:
Suitable extinguishing media:
Product is non-flammable, with a low risk of fire due to the flammability characteristics of the product in normal
conditions of storage, handling and use. In the case of the existence of sustained combustion as a result of
improper handling, storage or use any type of extinguishing agent can be used (ABC Powder, water,…)
Unsuitable extinguishing media:
Non-applicable
5.2Special hazards arising from the substance or mixture:
Due to its non-inflammable nature, the product does not present a fire risk under normal conditions of storage,
handling and use.
5.3Advice for firefighters:
Depending on the magnitude of the fire it may be necessary to use full protective clothing and self-contained
breathing apparatus (SCBA). Minimum emergency facilities and equipment should be available (fire blankets,
portable first aid kit,…).
Additional provisions:
Act in accordance with the Internal Emergency Plan and the Information Sheets on actions to take after an
accident or other emergencies. Eliminate all sources of ignition. In case of fire, cool the storage containers and
tanks for products susceptible to combustion, explosion or BLEVE as a result of high temperatures. Avoid spillage
of the products used to extinguish the fire into an aqueous medium.
SECTION 6: ACCIDENTAL RELEASE MEASURES
6.1Personal precautions, protective equipment and emergency procedures:
For non-emergency personnel:
Sweep up and shovel product or collect by other means and place in container for reuse (preferred) or disposal
For emergency responders:
Wear protective equipment. Keep unprotected persons away. See section 8.
Other information:
May form combustible dust concentrations in air. Keep away from sources of ignition – No smoking.
6.2Environmental precautions:
This product is not classified as hazardous to the environment. Keep product away from drains, surface and
ground water.
6.3Methods and material for containment and cleaning up:
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 2/8
BE769 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 6: ACCIDENTAL RELEASE MEASURES (continued)
It is recommended:
Sweep up and shovel product or collect by other means and place in container for reuse (preferred) or disposal
6.4Reference to other sections:
See sections 8 and 13.
SECTION 7: HANDLING AND STORAGE
7.1Precautions for safe handling:
A.-General precautions for safe use
Comply with the current legislation concerning the prevention of industrial risks with regards manually
handling weights. Maintain order, cleanliness and dispose of using safe methods (section 6).
B.-Technical recommendations for the prevention of fires and explosions
Due to its non-inflammable nature, the product does not present a fire risk under normal conditions of
storage, handling and use.
C.-Technical recommendations on general occupational hygiene
Do not eat or drink during the process, washing hands afterwards with suitable cleaning products.
D.-Technical recommendations to prevent environmental risks
It is not necessary to take special measures to prevent environmental risks. For more information see
subsection 6.2
Other information:
May form combustible dust concentrations in air. Keep away from sources of ignition – No smoking.
7.2Conditions for safe storage, including any incompatibilities:
A.-Technical measures for storage
Store in a cool, dry, well-ventilated location
B.-General conditions for storage
Avoid sources of heat, radiation, static electricity and contact with food. For additional information see
subsection 10.5
7.3Specific end use(s):
Except for the instructions already specified it is not necessary to provide any special recommendation regarding
the uses of this product.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1Control parameters:
Substances whose occupational exposure limits have to be monitored in the workplace:
Nuisance dust: Inhalable dust 10 mg/m3 // Respirable dust 4 mg/m3
DNEL (Workers):
Non-applicable
DNEL (General population):
Non-applicable
PNEC:
Non-applicable
8.2Exposure controls:
A.-Individual protection measures, such as personal protective equipment
As a preventative measure it is recommended to use basic Personal Protective Equipment, with the
corresponding <
cleaning, maintenance, class of protection, ) consult the information leaflet provided by the manufacturer. For
more information see subsection 7.1. All information contained herein is a recommendation which needs
some specification from the labour risk prevention services as it is not known whether the company has
additional measures at its disposal.
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 3/8
BE769 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION (continued)
B.-Respiratory protection
The use of protection equipment will be necessary if a mist forms or if the occupational exposure limits are
exceeded.
C.-Specific protection for the hands
Pictogram PPE Remarks
Mandatory hand
protection
Protective gloves against minor risks
Replace gloves in case of any sign of damage. For prolonged periods of
exposure to the product for professional users/industrials, we
recommend using CE III gloves in line with standards EN ISO
21420:2020 and EN ISO 374-1:2016+A1:2018
D.-Eye and face protection
Pictogram PPE Remarks
Mandatory face
protection
Panoramic glasses against
splash/projections.
Clean daily and disinfect periodically according to the manufacturer s
instructions. Use if there is a risk of splashing.
E.-Body protection
Pictogram PPE Remarks
Work clothing
Replace before any evidence of deterioration. For periods of prolonged
exposure to the product for professional/industrial users CE III is
recommended, in accordance with the regulations in EN ISO 6529:2013,
EN ISO 6530:2005, EN ISO 13688:2013, EN 464:1994.
Anti-slip work shoes
Replace before any evidence of deterioration. For periods of prolonged
exposure to the product for professional/industrial users CE III is
recommended, in accordance with the regulations in EN ISO
20345:2012 y EN 13832-1:2007
F.-Additional emergency measures
It is not necessary to take additional emergency measures.
Environmental exposure controls:
In accordance with the community legislation for the protection of the environment it is recommended to avoid
environmental spillage of both the product and its container. For additional information see subsection 7.1.D
The Volatile Organic Compounds in Paints, Varnishes and Vehicle Refinishing Products Regulations
2012:
V.O.C. (Supply): 0 % weight
V.O.C. density at 20 C: 0 kg/m (0 g/L)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
9.1Information on basic physical and chemical properties:
For complete information see the product datasheet.
Appearance:
Physical state at 20 C: Solid
Appearance: Not available
Colour: Green
Odour: Not available
Odour threshold: Non-applicable *
Volatility:
Boiling point at atmospheric pressure: Non-applicable *
Vapour pressure at 20 C: Non-applicable *
*Not relevant due to the nature of the product, not providing information property of its hazards.
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 4/8
BE769 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES (continued)
Vapour pressure at 50 C: Non-applicable *
Evaporation rate at 20 C: Non-applicable *
Product description:
Density at 20 C: ca. 700 kg/m
Relative density at 20 C: ca. 0.7
Dynamic viscosity at 20 C: Non-applicable *
Kinematic viscosity at 20 C: Non-applicable *
Kinematic viscosity at 40 C: Non-applicable *
Concentration: Non-applicable *
pH: Non-applicable *
Vapour density at 20 C: Non-applicable *
Partition coefficient n-octanol/water 20 C: Non-applicable *
Solubility in water at 20 C: Non-applicable *
Solubility properties: Non-applicable *
Decomposition temperature: Non-applicable *
Melting point/freezing point: Non-applicable *
Flammability:
Flash Point: Non-applicable
Flammability (solid, gas): Non-applicable *
Autoignition temperature: Non-applicable *
Lower flammability limit: Non-applicable *
Upper flammability limit: Non-applicable *
Explosive (Solid):
Lower explosive limit: Non-applicable *
Upper explosive limit: Non-applicable *
Particle characteristics:
Median equivalent diameter: Non-applicable *
9.2Other information:
Information with regard to physical hazard classes:
Explosive properties: Non-applicable *
Oxidising properties: Non-applicable *
Corrosive to metals: Non-applicable *
Heat of combustion: Non-applicable *
Aerosols-total percentage (by mass) of
flammable components:
Non-applicable *
Other safety characteristics:
Surface tension at 20 C: Non-applicable *
Refraction index: Non-applicable *
*Not relevant due to the nature of the product, not providing information property of its hazards.
SECTION 10: STABILITY AND REACTIVITY
10.1Reactivity:
No hazardous reactions are expected because the product is stable under recommended storage conditions. See
section 7 from Safety Data Sheet.
10.2Chemical stability:
Chemically stable under the indicated conditions of storage, handling and use.
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 5/8
BE769 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 10: STABILITY AND REACTIVITY (continued)
10.3Possibility of hazardous reactions:
Under the specified conditions, hazardous reactions that lead to excessive temperatures or pressure are not
expected.
10.4Conditions to avoid:
Applicable for handling and storage at room temperature:
Shock and friction Contact with air Increase in temperature Sunlight Humidity
Not applicable Not applicable Not applicable Not applicable Not applicable
10.5Incompatible materials:
Acids Water Oxidising materials Combustible materials Others
Avoid strong acids Not applicable Not applicable Not applicable
Avoid alkalis or strong
bases
10.6Hazardous decomposition products:
See subsection 10.3, 10.4 and 10.5 to find out the specific decomposition products. Depending on the
decomposition conditions, complex mixtures of chemical substances can be released: carbon dioxide (CO ),
carbon monoxide and other organic compounds.
SECTION 11: TOXICOLOGICAL INFORMATION
11.1Information on toxicological effects:
LD50 oral > 2000 mg/kg (rat)
Dangerous health implications:
In case of exposure that is repetitive, prolonged or at concentrations higher than the recommended occupational
exposure limits, adverse effects on health may result, depending on the means of exposure:
A-Ingestion (acute effect):
– Acute toxicity: Based on available data, the classification criteria are not met
– Corrosivity/Irritability: Based on available data, the classification criteria are not met
B-Inhalation (acute effect):
– Acute toxicity : Based on available data, the classification criteria are not met
– Corrosivity/Irritability: Based on available data, the classification criteria are not met
C-Contact with the skin and the eyes (acute effect):
– Contact with the skin: Based on available data, the classification criteria are not met
– Contact with the eyes: Based on available data, the classification criteria are not met
D-CMR effects (carcinogenicity, mutagenicity and toxicity to reproduction):
– Carcinogenicity: Based on available data, the classification criteria are not met
IARC: Non-applicable
– Mutagenicity: Based on available data, the classification criteria are not met
– Reproductive toxicity: Based on available data, the classification criteria are not met
E-Sensitizing effects:
– Respiratory: Based on available data, the classification criteria are not met
– Skin: Based on available data, the classification criteria are not met
F-Specific target organ toxicity (STOT) – single exposure:
Based on available data, the classification criteria are not met
G-Specific target organ toxicity (STOT)-repeated exposure:
– Specific target organ toxicity (STOT)-repeated exposure: Based on available data, the classification criteria
are not met
– Skin: Based on available data, the classification criteria are not met, as it does not contain substances
classified as hazardous for this effect. For more information see section 3.
H-Aspiration hazard:
Based on available data, the classification criteria are not met
Other information:
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 6/8
BE769 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 11: TOXICOLOGICAL INFORMATION (continued)
Non-applicable
Specific toxicology information on the substances:
Not available
SECTION 12: ECOLOGICAL INFORMATION
The experimental information related to the eco-toxicological properties of the product itself is not available
Based on available data, the classification criteria are not met
12.1Toxicity:
Not available
12.2Persistence and degradability:
Not available
12.3Bioaccumulative potential:
Not available
12.4Mobility in soil:
Not available
12.5Results of PBT and vPvB assessment:
Product does not meet PBT/vPvB criteria
12.6Other adverse effects:
Not described
SECTION 13: DISPOSAL CONSIDERATIONS
13.1Waste treatment methods:
Code Description Waste class
It is not possible to assign a specific code, as it depends on the intended use by the
user
Non dangerous
Type of waste:
Non-applicable
Waste management (disposal and evaluation):
Consult the authorized waste service manager on the assessment and disposal operations in accordance The
Waste Regulations 2011, 2011 No. 988. As under 15 01 of the code and in case the container has been in direct
contact with the product, it will be processed the same way as the actual product. Otherwise, it will be processed
as non-dangerous residue. Waste should not be disposed of to drains. See paragraph 6.2.
Regulations related to waste management:
In accordance with Annex II of UK REACH the provisions related to waste management are stated:
UK legislation: The Waste Regulations 2011.
SECTION 14: TRANSPORT INFORMATION
This product is not regulated for transport (ADR/RID,IMDG,IATA)
SECTION 15: REGULATORY INFORMATION
15.1Safety, health and environmental regulations/legislation specific for the substance or mixture:
– Substances listed in UK candidate list of substances of very high concern (SVHCs): Non-applicable
– Substances listed in UK REACH Authorisation List (Annex 14): Non-applicable
The Control of Major Accident Hazards Regulations 2015:
– CONTINUED ON NEXT PAGE –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 7/8
BE769 – Epoxy Tooling Board
Safety data sheet
According to UK REACH
SECTION 15: REGULATORY INFORMATION (continued)
Non-applicable
Restrictions to commercialisation and the use of certain dangerous substances and mixtures (Annex
XVII UK REACH, etc .):
Non-applicable
Specific provisions in terms of protecting people or the environment:
It is recommended to use the information included in this safety data sheet as a basis for conducting workplace-
specific risk assessments in order to establish the necessary risk prevention measures for the handling, use,
storage and disposal of this product.
Other legislation:
The REACH etc. (Amendment etc.) (EU Exit) Regulations 2020.
The Chemicals (Health and Safety) and Genetically Modified Organisms (Contained Use) (Amendment etc.) (EU
Exit) Regulations 2020.
Control of Substances Hazardous to Health Regulations 2002 (as amended)
EH40/2005 Workplace exposure limits.
SECTION 16: OTHER INFORMATION
Legislation related to safety data sheets:
This safety data sheet has been designed in accordance with ANNEX II-The REACH etc. (Amendment etc.) (EU
Exit) Regulations 2020.
Texts of the legislative phrases mentioned in section 3:
The phrases indicated do not refer to the product itself; they are present merely for informative purposes and
refer to the individual components which appear in section 3
GB CLP Regulation:
Non-applicable
Advice related to training:
Training is recommended in order to prevent industrial risks for staff using this product and to facilitate their
comprehension and interpretation of this safety data sheet, as well as the label on the product.
Principal bibliographical sources:
http://echa.europa.eu
http://eur-lex.europa.eu
Abbreviations and acronyms:
ADR: European agreement concerning the international carriage of dangerous goods by road
IMDG: International maritime dangerous goods code
IATA: International Air Transport Association
ICAO: International Civil Aviation Organisation
COD: Chemical Oxygen Demand
BOD5: 5day biochemical oxygen demand
BCF: Bioconcentration factor
LD50: Lethal Dose 50
LC50: Lethal Concentration 50
EC50: Effective concentration 50
LogPOW: Octanolwater partition coefficient
Koc: Partition coefficient of organic carbon
UFI: unique formula identifier
IARC: International Agency for Research on Cancer
Theinformationcontainedinthissafetydatasheetisbasedonsources,technicalknowledgeandcurrentlegislationatUK,withoutbeingabletoguaranteeitsaccuracy.
Thisinformationcannotbeconsideredaguaranteeofthepropertiesoftheproduct,itissimplyadescriptionofthesecurityrequirements.Theoccupationalmethodology
andconditionsforusersofthisproductarenotwithinourawarenessorcontrol,anditisultimatelytheresponsibilityoftheusertotakethenecessarymeasurestoobtain
thelegalrequirementsconcerningthemanipulation,storage,useanddisposalofchemicalproducts.Theinformationonthissafetydatasheetonlyreferstothisproduct,
whichshouldnotbeusedforneedsotherthanthosespecified.
– END OF SAFETY DATA SHEET –
Date of compilation: 14/03/2023 Revised: 09/10/2023 Version: 7 (Replaced 6) Page 8/8