INDEX
233M4154
233M41542
233M41543
3M Fastbond Foam Adhesive 100, Lavender 05/08/15
__________________________________________________________________________________________
Page 1 of 9
Safety Data Sheet
Copyright,2015,3M Company.
All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is
allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from
3M, and (2)neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.
Document Group:08-7614-4 Version Number: 18.00
Issue Date: 05/08/15 Supercedes Date: 07/30/10
SECTION 1: Identification
1.1. Product identifier
3M Fastbond Foam Adhesive 100, Lavender
Product Identification Numbers
62-4285-6535-2, 62-4285-8436-1, 62-4285-8530-1, 62-4285-9530-0, 62-4285-9538-3, 62-4285-9932-8, 62-4285-9939-3
1.2. Recommended use and restrictions on use
Recommended use
Adhesive, Industrial use
1.3. Supplier s details
MANUFACTURER: 3M
DIVISION: Industrial Adhesives and Tapes Division
ADDRESS: 3M Center, St. Paul, MN 55144-1000, USA
Telephone: 1-888-3M HELPS (1-888-364-3577)
1.4. Emergency telephone number
1-800-364-3577 or (651) 737-6501 (24 hours)
SECTION 2: Hazard identification
2.1. Hazard classification
Reproductive Toxicity: Category 1B.
2.2. Label elements
Signal word
Danger
Symbols
Health Hazard |
Pictograms
3M Fastbond Foam Adhesive 100, Lavender 05/08/15
__________________________________________________________________________________________
Page 2 of 9
Hazard Statements
Maydamage fertility or the unborn child.
Precautionary Statements
Prevention:
Obtain special instructions before use.
Do not handle until all safety precautions have been read and understood.
Wear protective gloves and eye/face protection.
Response:
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.
Continue rinsing.
If eye irritation persists: Get medical advice/attention.
IF exposed or concerned: Get medical advice/attention.
Storage:
Store locked up.
Disposal:
Dispose of contents/container in accordance with applicable local/regional/national/international regulations.
2.3. Hazards not otherwise classified
None.
SECTION 3: Composition/information on ingredients
Ingredient C.A.S. No. % by Wt
Water 7732-18-5 50 – 60 Trade Secret *
Polychloroprene 9010-98-4 40 – 50 Trade Secret *
Sodium Soap of Disproportationed Rosin 61790-51-0 1 – 5 Trade Secret *
Boric Acid 10043-35-3 < 1 Trade Secret *
Zinc Oxide 1314-13-2 < 1 Trade Secret *
*The specific chemical identity and/or exact percentage (concentration) of this composition has been withheld as a trade
secret.
SECTION 4: First aid measures
4.1. Description of first aid measures
Inhalation:
Remove person to fresh air. If you are concerned, get medical advice.
Skin Contact:
Wash with soap and water. If you are concerned, get medical advice.
Eye Contact:
Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get
medical attention.
If Swallowed:
Rinse mouth. If you are concerned, get medical advice.
3M Fastbond Foam Adhesive 100, Lavender 05/08/15
__________________________________________________________________________________________
Page 3 of 9
4.2. Most important symptoms and effects, both acute and delayed
See Section 11.1. Information on toxicological effects.
4.3. Indication of any immediate medical attention and special treatment required
Not applicable
SECTION 5: Fire-fighting measures
5.1. Suitable extinguishing media
Material will not burn. Use a fire fighting agent suitable for the surrounding fire.
5.2. Special hazards arising fromthe substance or mixture
None inherent in this product.
Hazardous Decomposition or By -Products
SubstanceCondition
Carbon monoxide During Combustion
Carbon dioxide During Combustion
Oxides of Nitrogen During Combustion
5.3. Special protective actions for fire-fighters
No special protective actions for fire-fighters are anticipated.
SECTION 6: Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
Evacuate area. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation
to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Refer to other sections of this SDS for
information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment.
6.2. Environmental precautions
Avoid release to the environment. For larger spills, cover drains and build dikes to prevent entry into sewer systems or
bodies of water.
6.3. Methods and material for containment and cleaning up
Contain spill. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially
available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent
material does not remove a physical, health, or environmental hazard. Collect as much of the spilled material as possible.
Place in a closed container approved for transportationby appropriate authorities. Clean up residue with water. Seal the
container. Dispose of collected material as soon as possible.
SECTION 7: Handling and storage
7.1. Precautions for safe handling
For industrial or professional use only. Do not handle until all safety precautions have been read and understood. Do not
breathe dust/fume/gas/mist/vapors/spray. Do not get in eyes, on skin, or on clothing. Do not eat, drink or smoke when using
this product. Wash thoroughly after handling. Avoid release to the environment. Avoid contact with oxidizing agents (eg.
chlorine, chromic acid etc.) Use personal protective equipment (gloves, respirators, etc.) as required.
7.2. Conditions for safe storage including any incompatibilities
Store awayfrom h eat. Store away from acids. Store away from oxidizing agents.
3M Fastbond Foam Adhesive 100, Lavender 05/08/15
__________________________________________________________________________________________
Page 4 of 9
SECTION 8: Exposure controls/personal protection
8.1. Control parameters
Occupational exposure limits
If a component is disclosed in section 3 but does not appear in the table below, an occupational exposure limit is not available
for the component.
Ingredient C.A.S. No.Agency Limit type Additional Comments
Boric Acid 10043-35-3ACGIH TWA(inhalable fraction):2
mg/m3;STEL(inhalable
fraction):6 mg/m3
A4: Not class. as human
carcin
Zinc Oxide 1314-13-2ACGIH TWA(respirable fraction):2
mg/m3;STEL(respirable
fraction):10 mg/m3
Zinc Oxide 1314-13-2OSHA TWA(as fume):5
mg/m3;TWA(as total dust):15
mg/m3;TWA(respirable
fraction):5 mg/m3
ACGIH : American Conference of Governmental Industrial Hygienists
AIHA : American Industrial Hygiene Association
CMRG : Chemical Manufacturer's Recommended Guidelines
OSHA :United States Department of Labor -Occupational Safety and Health Administration
TWA: Time-Weighted-Average
STEL: Short Term Exposure Limit
CEIL: Ceiling
8.2. Exposure controls
8.2.1. Engineering controls
Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to belowrelevant Exposure
Limits and/or control dust/fume/gas/mist/vapors/spray. If ventilation is not adequate, use respiratory protection equipment.
8.2.2. Personal protective equipment (PPE)
Eye/face protection
Select and use eye/face protection to prevent contact based on the results of an exposure assessment. The following eye/face
protection(s) are recommended:
Safety Glasses with side shields
Skin/hand protection
Select and use gloves and/or protective clothing approved to relevant local standards to prevent skin contact based on the
results of an exposure assessment. Selection should be based on use factors such as exposure levels, concentration of the
substance or mixture, frequency and duration, physical challenges such as temperature extremes, and other use conditions.
Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible gloves/protective
clothing.
Gloves made from the following material(s) are recommended: Neoprene
Nitrile Rubber
Natural Rubber
Respiratory protection
None required.
SECTION 9: Physical and chemical properties
9.1. Information on basic physical and chemical properties
3M Fastbond Foam Adhesive 100, Lavender 05/08/15
__________________________________________________________________________________________
Page 5 of 9
General Physical Form: Liquid
Odor, Color, Grade: Rubber odor, thin liquid, lavender.
Odor threshold No Data Available
pH 8.4 -9.3
Melting point Not Applicable
Boiling Point >=100 C
Flash Point No flash point
Evaporation rate 1.0 [Ref Std: WATER=1]
Flammability (solid, gas) Not Applicable
Flammable Limits(LEL) Not Applicable
Flammable Limits(UEL) Not Applicable
Vapor Pressure 17.5 mmHg [@ 68 F]
Vapor Density 1.1 [Ref Std: AIR=1]
Density 1.1 g/ml
Specific Gravity 1.1 [Ref Std: WATER=1]
Solubility in Water Complete
Solubility-non-water No Data Available
Partition coefficient: n-octanol/ water No Data Available
Autoignition temperature Not Applicable
Decomposition temperature No Data Available
Viscosity 15 -40 centipoise [@ 73.4 F ]
Hazardous Air Pollutants 0 % weight [Test Method: Calculated]
VOC Less H2O & Exempt Solvents <=20 g/l [Test Method: calculated SCAQMD rule 443.1]
Solids Content 40 -50 %
SECTION 10: Stability and reactivity
10.1. Reactivity
This material may be reactive with certain agents under certain conditions -see the remaining headings in this section.
10.2. Chemical stability
Stable.
10.3. Possibility of hazardous reactions
Hazardous polymerization will not occur.
10.4. Conditions to avoid
Heat
10.5. Incompatible materials
Strong acids
Strong oxidizing agents
10.6. Hazardous decomposition products
Substance Condition
None known.
Refer to section 5.2 for hazardous decomposition products during combustion.
SECTION 11: Toxicological information
The information below may not be consistent with the material classification in Section 2 if specific ingredient
classifications are mandated by a competent authority. In addition, toxicological data on ingredients may not be
3M Fastbond Foam Adhesive 100, Lavender 05/08/15
__________________________________________________________________________________________
Page 6 of 9
reflected in the material classification and/or the signs and symptoms of exposure, because an ingredient may be
present below the threshold for labeling, an ingredient may not be available for exposure, or the data may not be
relevant to the material as a whole.
11.1. Information on Toxicological effects
Signs and Symptoms of Exposure
Based on test data and/or information on the components, this material may produce the following health effects:
Inhalation:
No known health effects.
Skin Contact:
Contact with the skin during product use is not expected to result in significant irritation.
Eye Contact:
Contact with the eyes during product use is not expected to result in significant irritation.
Ingestion:
No known health effects.
Additional Health Effects:
Reproductive/Developmental Toxicity:
Contains a chemical or chemicals which can cause birth defects or other reproductive harm.
Toxicological Data
If a component is disclosed in section 3 but does not appear in a table below, either no data are available for that endpoint or
the data are not sufficient for classification.
Acute Toxicity
Name Route SpeciesValue
Overall product Ingestion No data available; calculated ATE > 5,000 mg/kg
Polychloroprene Dermal LD50 estimated to be > 5,000 mg/kg
Polychloroprene IngestionRat LD50 > 20,000 mg/kg
Zinc Oxide Dermal LD50 estimated to be > 5,000 mg/kg
Zinc Oxide Inhalation-
Dust/Mist
(4 hours)
Rat LC50 > 5.7 mg/l
Zinc Oxide IngestionRat LD50 > 5,000 mg/kg
ATE = acute toxicity estimate
Skin Corrosion/Irritation
Name SpeciesValue
Polychloroprene Human No significant irritation
Zinc Oxide Human
and
animal
No significant irritation
Serious Eye Damage/Irritation
Name SpeciesValue
Polychloroprene Professio
nal
judgeme
nt
No significant irritation
Zinc Oxide Rabbit Mild irritant
3M Fastbond Foam Adhesive 100, Lavender 05/08/15
__________________________________________________________________________________________
Page 7 of 9
Skin Sensitization
Name SpeciesValue
Zinc Oxide Guinea
pig
Some positive data exist, but the data are not
sufficient for classification
Respiratory Sensitization
For the component/components, either no data are currently available or the data are not sufficient for classification.
Germ Cell Mutagenicity
Name Route Value
Zinc Oxide In VitroSome positive data exist, but the data are not
sufficient for classification
Zinc Oxide In vivo Some positive data exist, but the data are not
sufficient for classification
Carcinogenicity
For the component/components, either no data are currently available or the data are not sufficient for classification.
Reproductive Toxicity
Reproductive and/or Developmental Effects
Name Route Value SpeciesTest Result Exposure
Duration
Zinc Oxide IngestionSome positive
reproductive/developmental data exist,
but the data are not sufficient for
classification
Multiple
animal
species
NOAEL 125
mg/kg/day
premating &
during
gestation
Target Organ(s)
Specific Target Organ Toxicity -single exposure
For the component/components, either no data are currently available or the data are not sufficient for classification.
Specific Target Organ Toxicity -repeated exposure
Name Route Target Organ(s) Value SpeciesTest Result Exposure
Duration
Zinc Oxide Ingestionnervous system Some positive data exist, but the
data are not sufficient for
classification
Rat NOAEL 600
mg/kg/day
10 days
Zinc Oxide Ingestionendocrine system |
hematopoietic
system | kidney
and/or bladder
Some positive data exist, but the
data are not sufficient for
classification
Other NOAEL 500
mg/kg/day
6 months
Aspiration Hazard
For the component/components, either no data are currently available or the data are not sufficient for classification.
Please contact the address or phone number listed on the first page of the SDS for additional toxicological information
on this material and/or its components.
SECTION 12: Ecological information
Ecotoxicological information
Please contact the address orphone number listed on the first page of the SDS for additional ecotoxicological information on this material
and/or its components.
Chemical fate information
3M Fastbond Foam Adhesive 100, Lavender 05/08/15
__________________________________________________________________________________________
Page 8 of 9
Please contact the address or phone number listed on the first page of the SDS for additional chemical fate information on this material
and/or its components.
SECTION 13: Disposal considerations
13.1. Disposal methods
Dispose of contents/ container in accordance with the local/regional/national/international regulations.
Dispose of waste product in a permitted industrial waste facility. As a disposal alternative, incinerate in a permitted waste
incineration facility. Proper destruction may require the use of additional fuel during incineration processes. Empty
drums/barrels/containers used for transporting and handling hazardous chemicals (chemical substances/mixtures/preparations
classified as Hazardous as per applicable regulations) shall be considered, stored, treated & disposed of as hazardous wastes
unless otherwisedefined by applicable waste regulations. Consult with the respective regulating authorities to determine the
available treatment and disposal facilities.
EPA Hazardous Waste Number (RCRA): Not regulated
SECTION 14: Transport Information
Not regulated per U.S. DOT, IATA or IMO.
These transportation classifications are provided as a customer service. As the shipper YOU remain responsible for
complying with all applicable laws and regulations, including proper transportation classification and packaging.3M
transportation classifications are based on product formulation, packaging, 3M policies and 3M understanding of
applicable current regulations. 3M does not guarantee the accuracy of this classification information. This information
applies only to transportation classification and notthe packaging, labeling, or marking requirements. The original 3M
package is certified for U.S. ground shipment only. If you are shipping by air or ocean, the package may not meet
applicable regulatory requirements.
SECTION 15: Regulatory information
15.1. US Federal Regulations
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard -No Pressure Hazard -No Reactivity Hazard -No Immediate Hazard -No Delayed Hazard -Yes
15.2. State Regulations
Contact 3M for more information.
15.3. Chemical Inventories
The components of this product are in compliance with the chemical notification requirements of TSCA.
Contact 3M for more information.
15.4. International Regulations
Contact 3M for more information.
This SDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: Other information
3M Fastbond Foam Adhesive 100, Lavender 05/08/15
__________________________________________________________________________________________
Page 9 of 9
NFPA Hazard Classification
Health: 1 Flammability: 0 Instability: 0 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address
the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar
emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include
the toxic properties of combustion or decomposition products that are known to be generated insignificant quantities.
Document Group:08-7614-4 Version Number: 18.00
Issue Date: 05/08/15 Supercedes Date: 07/30/10
DISCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. 3M MAKES
NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR
USAGE OF TRADE. User is responsible for determining whether the 3M product isfit for a particular purpose and suitable
for user’s method of use or application. Given the variety of factors that can affect the use and application of a 3M product,
some of which are uniquely within the user’s knowledge and control, it is essential that the user evaluate the 3M product to
determine whether it is fit for a particular purpose and suitable for user’s method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer
may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness
or accuracy. In addition, information obtained from a database may not be as current as the information in the SDS available
directly from 3M
3MUSA SDSs are available at www.3M.com