MATERIAL SAFETY DATA SHEETS
1. CHEMICAL PRODUCT
Adhesive Systems, Inc.
9411 Corsair Road
Frankfort, IL 60423
1-800-552-0299 Phone
1-815-464-5650 Fax
EMERGENCY PHONE 1-800-255-3924 In ternational +01+813-248-0585
Product Name: MP55310 Part A (Resin)
Technical Name: Methyl Methacrylate
2. HAZARDS IDENTIFICATION
Primary Routes of Entry: Inhalation and skin
Symptoms of Exposure: Eyes-redness, swelling, tearing, and hazy vision.
Skin-redness, swelling, and itching.
Inhalation- Soreness of the nose and throat, coughing.
Medical Conditions Aggravated
by Exposure: Preexisting eye, respiratory, and skin disorders may be aggravated by
exposure.
Carcinogenicity: None
Hazard Classification
Physical Classification: Flammable Liquid and vapor Category 3
Symbol:
Signal Word: Danger
Health Classification:
Irritant: Causes mild skin or eye irritation Category 3
Symbol:
Signal Word: Warning
3. COMPOSITION AND INFORMATION ON HARMFUL INGREDIENTS
REVISED
March 2014
Ingredients Cas No.
OSHA PEL
ACGIH TLV
Other Limits %Composition
Methyl Methacrylate
Chlorosulfonated
Polyethylene
Maleic Acid
80-62-6
68037-39-8
110-16-7
100ppm
N.E.
N.E.
50ppm
N.E.
N.E.
100ppm (Canada)
N.E.
N.E.
45-65
20-30
1-5
*Proprietary means the specific chemical identity and/or weight percent is being withheld as a trade secret.
Page 1 of 4
MATERIAL SAFETY DATA SHEETS
MP55310 Part A (Resin)
Methyl Methacryalte
4. FIRST AID MEASURES
Ingestion: Get immediate medical att ention, DO NOT INDUCE VOMITING.
Inhalation: Remove to fresh air, if symptoms continue, seek medical advice.
Skin Contact: Soak in warm soapy water. Discard contam inated clothing. Do not use organic solvents. If
irritation occurs, get medical attention.
Eye Contact: Immediately flush eyes with water fo r at least 20 minutes, seek medical attention.
5. FIRE FIGHTING MEASURES
Flammable Limits: LEL=2.1 for MMA UEL=12.5 for MMA
Extinguishing Media: Use dry chemical powder. Insoluble in water.
Special Fire Fighting Procedures: Wear self cont ained breathing apparatus and full turnout gear.
Unusual Fire / Explosion Hazards: None
6. ACCIDENTAL RELEASE MEASURES
Ventilate area of spill. Flood area with water to polymerize. Absorb with sand / earth and dispose in accordance
with local, state, and federal regulations.
7. HANDLING AND STORAGE
When using large volumes ensure that operational area is well ventilated.
Store between 5-25 C; avoid strong light and heat sources. These products should never be frozen.
Avoid skin contact and inhalation of vapor.
8. EXPOSURE CONTROL AND PERSONAL PROTECTION
OSHA PEL: N/A
TLV: 0.2 ppm TWA
Engineering Controls: Use good gener al local ventilation when working with this material.
Eye Protection: Safety goggles / glasses suitable for use with chemicals.
Respiratory Protection: Always use appropriate filter mask / respirator.
Skin Protection: Nitrile / polyethylene gloves, coveralls, avoid cotton products.
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance and Odor: Light gel, pungent, acrylic odor
Flashpoint: 51 F (TCC) Solubility in Water: Slight Boiling Point:214 F for MMA Specific Gravity: 0.94-1.0 @25 C Evaporation rate: N/D Melting Point: N/D Vapor Pressure: 29mm @ 20 C Vapor Density:>1, 3.5 for MMA V .O.C. Content: <50g/L Page 2 of 4 MATERIAL SAFETY DATA SHEETS MP55310 Part A (Resin) Methyl Methacryalte 10. REACTIVITY AND STABILIITY Chemical Stability: Stable Hazardous Polymerization: May occur , Excessive aging and/or heat, polymerization catalysts, oxygen-free atmosphere, inhibitor depletion, direct sunlight. Incompatibility: Oxidizers, acids, bases, uv radiation, amines. Conditions to Avoid: None Hazardous Decomposition Products: Carbon and nitro gen oxides, hydrogen cyanide, methylene bisphenyl, isocyanate, hydrocarbons 11. TOXICOLOGICAL INFORMATION Routes of Exposure; Inhalation and skin Related Symptoms: Moderate respiratory tract i rritation. Moderate skin irritation , redness. Chronic Effects: Chronic Exposure may lead to kidney or liver damage. Use adequate ventilation to maintain airborne concentration below exposure lim its. Not believed to represent a carcinogenic or mutagenic hazard. 12. ECOLOGICAL INFORMATION None. 13. DISPOSAL INFORMATION This material must be disposed in compliance with l ocal, state, and federal regulations. When in consumer packaging this material must be disposed of as household waste. Check local and state regulat ions for disposal of this product as a household waste in your state or municipality. 14. TRANSPORTATION INFORMATION U.S.DOT Materials shipped in Quantities of more than 1 Liter in combination or single packaging. UN 1133 Adhesives 3 II Limited quantities, No shipping paper required. Limited quantity mark is required on the outer surface of the finished package. ICAO/IATA Materials shipped in Quantities of more than 1 Liter in combination or single packaging. UN 1133 Adhesives 3 II Materials shipped in Limited Quantities ID 8000 Consumer Commodity 9 (Limited Quantity Marking with Y required on outer surface of the package and Class 9 label also `required on the outer surface of the package) IMDG Materials shipped in Quantities of more than 1 Liter in combination or single packaging. UN 1133 Adhesives 3 II Limited quantities in combination packages only: UN1133 Adhesives 3 II Ltd. Qty (FP in degrees C c.c. required on shipping paper) Limited marking only required on outer surface of package. Page 3 of 4 MATERIAL SAFETY DATA SHEETS MP55310 Part A (Resin) Methyl Methacryalte 15. REGULATORY INFORMATION TSCA All ingredients of this product are listed, or are exempt from listing, on the TSCA inventory. SARATitleIII,Section13 This product does contain the following chemical(s) which are defined as toxic chemicals und er and subject to the reporting requirements of, Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and40CFRPart372. Methyl Methacrylate 16. OTHER INFORMATION Initial: 8/22/2007 Revised: March 2014 HMIS HEALTH 2 FLAMMABILITY 3 REACTIVITY 2 NON-WARRANTY: Information contained herein is based on tests we believe to be reliable and accurate. It is offered in good faith for the benefit of the consumer. Adhesive Systems shall not be liable for any injury, loss, or damage in the use of it's chemical products since the conditions of use are beyond our control. In every case we urge and recommend the user conduct tests to determine to their own satisfaction that the product is of acceptable quality and is suitable for their particular purpose under their own operating conditions. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent. Because of changing reporting requirements and other variables it is impossible to guarantee the accuracy of the information contained in this document. It is the responsibility of the user to determine proper personal protection based on the actual condition of use and to comply with all Federal, State, and Local laws and regulations. Revised Au gust 2013 Page 4 of 4 MATERIAL SAFETY DATA SHEETS 1. CHEMICAL PRODUCT Adhesive Systems, Inc. 9411 Corsair Road Frankfort, IL 60423 1-800-552-0299 Phone 1-815-464-5650 Fax EMERGENCY PHONE 1-800-255-3924 In ternational +01+813-248-0585 Product Name: MP55310 Part B (Activator) Technical Name: Methyl Methacrylate 2. HAZARDS IDENTIFICATION Primary Routes of Entry: Inhalation and skin Symptoms of Exposure: Eyes-redness, swelling, tearing, and hazy vision. Skin-redness, swelling, and itching. Inhalation- Soreness of the nose and throat, coughing. Medical Conditions Aggravated by Exposure: Preexisting eye, repiratory, and skin disorders may be aggravated by exposure. Carcinogenicity: None Hazard Classification Physical Classification: Flammable Liquid Category 3 Symbol: Signal Word: Danger Health Classification: Irritant: Causes mild skin or eye irritation Category 3 Symbol: Signal Word: Warning 3. COMPOSITION AND INFORMATION ON HARMFUL INGREDIENTS REVISED March 2014 Ingredients Cas No. OSHA PEL ACGIH TLV Other Limits %Composition Methyl Methacrylate P(BD/MMA/STY) 80-62-6 25053-09-2 100ppm N.E. 50ppm N.E. 100ppm (Canada) N.E 65-85 5-15 Page 1 of 4 MATERIAL SAFETY DATA SHEETS MP55310 Part B (Activator) Methyl Methacryalte 4. FIRST AID MEASURES Ingestion: Get immediate medical att ention,DO NOT INDUCE VOMITING. Inhalation: Remove to fresh air, if symptoms continue, seek medical advice. Skin Contact: Soak in warm soapy water.Discard contami nated clothing. Do not use organic solvents. If irritation occurs, get medical attention. Eye Contact: Immediately flush eyes with water fo r at least 20 minutes, seek medical attention. 5. FIRE FIGHTING MEASURES Flammable Limits: LEL=2.1 for MMA UEL=12.5 for MMA Extinguishing Media: Use dry chemical powder. Insoluble in water. Special Fire Fighting Procedures: Wear self cont ained breathing apparatus and full turnout gear. Unusual Fire / Explosion Hazards: None 6. ACCIDENTAL RELEASE MEASURES Ventilate area of spill. Flood area with water to polymerize. Absorb with sand / earth and dispose in accordance with local, state, and federal regulations. 7. HANDLING AND STORAGE When using large volumes ensure that operational area is well ventilated. Store between 5-25 C; avoid strong light and heat sources.These products shoul d never be frozen. Avoid skin contact and inhalation of vapor. 8. EXPOSURE CONTROL AND PERSONAL PROTECTION Engineering Controls: Use good gener al local ventilation when working with this material. Eye Protection: Safety goggles / glasses suitable for use with chemicals. Respiratory Protection: Always use appropriate filter mask / respirator. Skin Protection: Nitrile / polyethylene gloves, coveralls, avoid cotton products. 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance and Odor: Off white, black, or grey liquid. Flashpoint: 51 F (TCC) Solubility in Water: Slight Boiling Point:214 F for MMA Specific Gravity: 1.2-1.3 @25 C Evaporation rate: N/D Melting Point: N/D Vapor Pressure: 29mm @ 20 C Vapor Density:>1, 3.5 for MMA V .O.C. Content: <50g/L Page 2 of 4 MATERIAL SAFETY DATA SHEETS MP55310 Part B (Activator) Methyl Methacryalte 10. REACTIVITY AND STABILITY Chemical Stability: Stable Hazardous Polymerization: May occur , Excessive aging and/or heat, polymerization catalysts, oxygen-free atmosphere, inhibitor depletion, direct sunlight. Incompatibility: Oxidizers, acids, bases, uv radiation, amines. Conditions to Avoid: None Hazardous Decomposition Products: Carbon and nitro gen oxides, hydrogen cyanide, methylene bisphenyl, isocyanate, hydrocarbons 11.TOXICOLOGICAL INFORMATION Routes of Exposure; Inhalation and skin Related Symptoms: Moderate respiratory tract i rritation. Moderate skin irritation , redness. Chronic Effects: Chronic Exposure may lead to kidney or liver damage. Use adequate ventilation to maintain airborne concentration below exposure lim its. Not believed to represent a carcinogenic or mutagenic hazard. 12. ECOLOGICAL INFORMATION None. 13. DISPOSAL INFORMATION This material must be disposed in compliance with l ocal, state, and federal regulations. When in consumer packaging this material must be disposed of as household waste. Check local and state regulat ions for disposal of this product as a household waste in your state or municipality. 14. TRANSPORTATION INFORMATION U.S.DOT Materials shipped in Quantities of more than 1 Liter in combination or single packagings UN 1133 Adhesives 3 II Limited quantities, No shipping paper required. Limited quantity mark is required on the outer surface of the finished package. ICAO/IATA Materials shipped in Quantities of more than 1 Liter in combination or single packagings UN 1133 Adhesives 3 II Materials shipped in Limited Quantities ID 8000 Consumer Commodity 9 (Limited Quantity Marking with Y required on outer surface of the package and Class 9 label also `required on the outer surface of the package) IMDG Materials shipped in Quantities of more than 1 Liter in combination or single packagings UN 1133 Adhesives 3 II Limited quantities in combination packages only: UN1133 Adhesives 3 II Ltd. Qty (FP in degrees C c.c. required on shipping paper) Limited marking marking only required on outer surface of package. Page 3 of 4 MATERIAL SAFETY DATA SHEETS MP55310 Part B (Activator) Methyl Methacryalte 15. REGULATORY INFORMATION TSCA All ingredients of this product are listed, or are exempt from listing, on the TSCA inventory. SARATitleIII,Section13 This product does contain the following chemical(s) which are defined as toxic chemicals und er and subject to the reportingrequirements of, Section 313 of Title III of the Superfund Amendm ents and Reauthorization Act of 1986 and40CFRPart372. Methyl Methacrylate 16. OTHER INFORMATION Initial: 8/22/2007 Revised: March 2014 HMIS HEALTH 2 FLAMMABILITY 3 REACTIVITY 2 NON-WARRANTY: Information contained herein is based on tests we believe to be reliable and accurate. It is offered in good faith for the benefit of the consumer. Adhesive Systems shall not be liable for any injury, loss, or damage in the use of it's chemical products since the conditions of use are beyond our control. In every case we urge and recommend the user conduct tests to determine to their own satisfaction that the product is of acceptable quality and is suitable for their particular purpose under their own operating conditions. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent. Because of changing reporting requirements and other variables it is impossible to guarantee the accuracy of the information contained in this document. It is the responsibility of the user to determine proper personal protection based on the actual condition of use and to comply with all Federal, State, and Local laws and regulations. Page 4 of 4