TD035 ICP Group, Inc. Rev 1/2021-1 Page 1 of 3
TECHNICAL DATA SHEET
HANDIFOAM
COMMERCIAL VEHICLE SPRAY FOAM
LOW PRESSURE POLYURETHANE FOAM INFORMATION
Description Low pressure, medium density, black in color, two-component spray polyurethane foam
SPF Spray Polyurethane Foam
Applications Designed to coat flat or irregular surfaces. The foam easily blends in with the undercarriages of RVs and other
vehicles while helping to reduce vibration and deaden sound.
Preparation for
use
Substrate must be clean, dry, firm, free of loose particles, and free of dust, grease, and mold release agents.
Protect surfaces not to be foamed. Read SDS, Operating Instructions, and Product Stewardship Guidelines. For
additional information go to www.Handifoam.com
Use Condition chemicals to 75-85 F (24-29 C). Follow instructions for set-up found in the operating instructions.
PPE
Recommend using in a well-ventilated area with certified respiratory protection or a powered air purifying
respirator (PAPR). Wear protective glasses with side shields or goggles, nitrile gloves, and clothing that protects
against dermal exposure. Read all instructions and SDS prior to use of any product.
Note FOR PROFESSIONAL USE ONLY. Always check the local building code before use. Cured low pressure
polyurethane foam is non-toxic and inert.
Product Storage Store in a dry area. Do not expose the kits or tanks to open flame or temperatures above 90 F (32 C).
Excessive heat can cause premature aging of components resulting in a shorter shelf-life.
Temperature Please see chart located on page 2.
Disposal Refer to SDS (Section 13) for instructions. Always dispose of empty cylinders in accordance with all applicable
federal, state, provincial and local regulations.
Shelf-life 12 months
Compatibility Cured low pressure polyurethane foam is chemically inert and non-reactive in approved applications, and will not
harm electrical wire insulations, extruded polystyrene foams, Romex
, rubber, PVC, polyethylene (i.e. PEX) or
other plastics. The product is not resistant to UV rays; if left exposed the product should be coated or painted.
TECHNICAL DATA STANDARD RESULTS
Density Free Rise ASTM D1622 1.75 lbs/ft
3
(28 kg/m
3
)
K-factor- Aged 90 days 140
F (60
C) ASTM C518 0.139 BTU inch/ft
2
h F
0.166 BTU inch/ft
2
h F
0.083 BTU inch/ft
2
h F
R-Value- Aged 90 days 140
F (60
C) ASTM C518 7.2 at 1 inch thickness
6.0 at 1 inch thickness
12.0 at 2 inch thickness
Air Barrier Properties-Estimated ASTM E283 0.003 cfm/ft
2
(0.02 L/s/m
2
)
Tested at 1 inch thickness @1.57 psf (75 Pa)
Perm Rating-1 inch thickness ASTM E96 0.02 L/s/m
2
Compressive Strength ASTM D1621 26 lbf/in
2
(182 kPa) Parallel
Dimensional Stability ASTM D2126 +/- 5%
Tack-Free/Expansion Time Tack-Free/Expansion Time 30-60 seconds
Closed-Cell Content ASTM D2856 95%
Cuttable 2-5 minutes
HandiFoam
Commercial Vehicle Spray Foam
TD035 ICP Group, Inc. Rev 1/2021-1 Page 2 of 3
Fungi Resistance ASTM G21 No Growth
Fire Rating FMVSS302/CMVSS 302 Meets/ Burn Rate 0/00 min
Fire Rating- Tested at 1 Thickness ASTM E84 Flame Spread Index 20
Smoke Developed 400
APPROVALS/STANDARDS/CLASSIFICATIONS
TEMPERATURE GUIDELINES
Chemical Storage Temperature Optimum 75-85 F (24-29 C) but not <60 F (16 C) or >90 F (32 C)
Outside Application Temperature 40-100 F (4-38 C)
Process Core Chemical Temperature 75-85 F (24-29 C)
Surface Temperature (Substrate) 40-100 F (4-38 C)
Cured Foam
–
200 F to
+
240 F (
–
129 C to
+
116 C)
YIELD
1
(2.10 Free Rise Density)
Weight
(Including Packaging)
Board Feet Cubic Feet
P12756 116 lbs
(52.6 kg)
504
(46.8 m
2
)
42.0 ft
3
(1.19 m
3
)
1
Yield is based on free-rise density. We state our core density/free-rise density when describing the foam. Applying foam into a cavity may result
in higher in-place densities due to packing effects. These higher densities may result in lower yields.
ASTM E84 Conforms to the requirements of ASTM E84 and is classified as a class 1 (A) material. Tested at 1 inch
thickness
HandiFoam
Commercial Vehicle Spray Foam
TD035 ICP Group, Inc. Rev 1/2021-1 Page 3 of 3
NOTE: Physical properties shown are typical and are to serve only as a guide for engineering design. Results are obtained from specimens under ideal laboratory
conditions and may vary upon use, temperature and ambient conditions. Right to change physical properties as a result of technical progress is reserved. Yields shown
are optimum and will vary slightly depending on ambient conditions and application. This information supersedes all previously published data. The customer is
responsible for deciding whether products and associated TDS information are appropriate for customer s use.
WARNING:
ICP low pressure one-component polyurethane foam sealants and adhesives (OCF), low pressure spray polyurethane foams and foam adhesives (SPF), and low pressure
pour-in-place polyurethane foams (PIP) are composed of diisocyanate, hydrofluorocarbon, hydrocarbon, hydrofluoroolefin or hydrochlorofluoroolefin blowing agent, and a
polyol blend. The urethane foam produced from these ingredients will support combustion and may present a fire hazard if exposed to a fire or excessive heat about 240 F
(116 C). Read all instructions, ICP Product Stewardship Guidelines and SDS (Section 8) prior to use of any product. ICP polyurethane products are for professional use
only.
Before using any OCF, SPF or PIP product, read the SDS and instructions carefully before use (www.handifoam.com). OCF Products: wear protective glasses with side
shields or goggles, nitrile gloves, and clothing that protects against dermal exposure. Recommend using in a well-ventilated area. Avoid breathing vapors. SPF/PIP
Products: wear protective glasses with side shields or goggles unless using a full-face respirator, nitrile gloves, and clothing that protects against dermal exposure.
Recommend dispensing product in a well-ventilated area and with certified respiratory protection or a powered air purifying respirator (PAPR); however, well ventilated
exterior applications may not need respiratory protection. It is the responsibility of the employer to complete a PPE evaluation and/or exposure assessment to determine if
respiratory protection is required. Personal Protective Equipment can be purchased through ICP Building Solutions Group by ordering the Polyset Contractor Safety Kit
(F65251). The Contractor Safety Kit includes: nitrile gloves, contractor safety glasses, and a size Medium NIOSH-approved negative pressure half mask respirator.
Refer to each product s TDS for specifications, testing results, and other attributes. The customer is ultimately responsible for deciding whether products and associated
TDS information are appropriate for customer s use. For professional use only. Building practices unrelated to materials can lead to potential mold issues. Material suppliers
cannot provide assurance that mold will not develop in any specific system. Product uses a non-flammable compressed gas. Keep away from heat. Smoking and open
flames, including hot work, should be prohibited in the vicinity of a foaming operation. Avoid contact with skin and eyes. May cause sensitization by inhalation and/or direct
skin contact. Persons previously sensitized to Isocyanates may develop a cross-sensitization reaction to other isocyanates. Avoid prolonged or repeated breathing of vapor.
Use in conformance with all local, state and federal regulations and safety requirements. Failure to strictly adhere to any recommended procedures and reasonable safety
precautions shall release ICP Building Solutions Group of all liability with respect to the materials or the use thereof. For additional information and location of your nearest
distributor, call ICP Building Solutions Group 330.753.4585.
LIMITED WARRANTY and LIMITATION OF DAMAGES: ICP Building Solutions Group warrants only that the product shall meet ICP Building Solutions Group s
specifications for the product when shipped by ICP Building Solutions Group. NO OTHER EXPRESSED OR IMPLIED WARRANTIES APPLY AND ANY IMPLIED
WARRANTIES OF MERCH ANTABILITY, NON-INFRINGEMENT OUTSIDE THE U.S. AND FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY DISCLAIMED.
Buyer and users assume all risks of use, handling and storage of the product. Failure to strictly adhere to any recommended procedures shall release ICP Building Solutions
Group from all liability. The user of the product is responsible to determine suitability of the product for the particular use. The exclusive remedy as to any breach of warranty,
negligence or other claim is limited to the replacement of the product. Liability for any indirect, incidental or consequential damage or loss is specifically excluded.