25PBFASTG_TDS.pdf

2012
February 2012
PB FAST SET One Part Bonding Adhesive DESCRIPTION: PB Fast Set is an amber-colored, one-part, urethane adhesive that fully cures in 30 minutes. It works well for indoor or outdoor applications. It cures from liquid to solid with a slight amount of moisture. Use it to join Precision Board Plus high density urethane sheets to make them longer or wider, and for laminating sheets together to make them thicker. Consistency of PB Fast Set is similar to honey, making it easy to apply directly from the container. No mixing is required. Works well on wood, metal and most other materials. Easy to cut, carve, sand or machine and cuts cleanly (Working time: Approximately 4 minutes). For slower cure and more working time, use PB Bond-240. Working time: Approximately 4 minutes. Preparation – Lightly spray the mating surfaces with water, or wipe the surfaces with a damp rag just prior to applying the PB Fast Set. This procedure assures there will be adequate moisture to effect total cure. PB Fast Set will not cure properly without adding moisture. Excessive water will slow cure time, and soften adhesive. Application – Apply a very thin coat of PB Fast Set to one of the surfaces to be joined, applying only enough to change the color of Precision Board Plus. Excess adhesive will be pushed out of the joint. Hold pieces in place by clamping or by setting something heavy on each side of the joint. Clean up wet adhesive with acetone. Keep container closed when not in use. Coverage is approximately 1/2 ounce per square foot. Edge Bonding – After application, the adhesive will start to bubble and thicken in approximately 1-2 minutes. Keep the Precision Board pieces on edge during this time so that the PB Fast Set will not run out of the joint before it sets. If the adhesive runs out, the joint may look solid but will be hollow inside, therefore extremely weak. Laminate Bonding – When making laminate bonds, the moisture added will assure total cure. If moisture is not added there will be spots of uncured adhesive where moisture was unable to penetrate. Even long term drying will not complete reaction since PB does not absorb moisture from the air and pass it through to the joint. Sandblasting When edge-bonding pieces that will be sandblasted, do not apply PB Fast Set to the top part of the joint since it will be blasted away later. Clamping is necessary, as thick bond lines are harder to blast through. Remove any excess adhesive from the joint. Tips For Easier Usage Lightly spray or wipe mating pieces with water just prior to application. Too much water slows cure. Apply just enough PB Fast Set to change the color of Precision Board Plus. Allow PB Fast Set to slightly bubble and thicken before pushing pieces together. Allow minimum of 30 minutes prior to moving bonded part. Keep adhesive back from outer edge for ease of sandblasting. Clamping is necessary. To blend joint into background after sanding, prime with FSC-88 WB primer/filler. Drill small hole in cap to act as dispensing nozzle. After using, cover hole with tape. NOTE: For questions regarding use of PB Fast Set, please contact Coastal Enterprises at (800) 845-0745. See the training video at www.precisionboard.com CAUTION: For industrial use only. Use with adequate ventilation. Avoid prolonged contact with skin. Close container after each use. Do not take internally. Do not transfer contents to bottles or other unlabeled containers. Harmful or fatal if swallowed. Do not induce vomiting. Call physician immediately. KEEP OUT OF REACH OF CHILDREN. WARRANTY: All recommendations for product use have been derived from experience and test data believed to be reliable. We warrant and guarantee the uniformity of our products within manufacturing tolerance. However, since the use of our products are beyond our direct control, they are furnished upon the condition that each party shall make his/her own tests to determine their suitability for his/her particular purpose. Except as stated herein, Coastal Enterprises Company makes no warranty or guarantee, expressed or implied, and disclaims all responsibility for results obtained, nor assumes any liability for any damages, whether arising out of negligence or breach of guarantee and is hereby expressly limited to replacement of product only. For additional information on product handling, please refer to PB Fast Set MSDS.