Divinycell H provides excellent mechanical properties to low weight.
The unique IPN chemical structure, yields impressive mechanical
performance to a low weight. Divinycell H has been widely used and
has a proven track record in virtually every application area where
sandwich composites are employed including the marine (leisure,
military and commercial), land transportation, wind energy, civil
engineering/infrastructure and general industrial markets.
Divinycell H is ideal for applications subject to fatigue, slamming or
impact loads. Other key features of Divinycell H include consistent
high quality, excellent adhesion/peel strength, excellent chemical
resistance, low water absorption and good thermal/acoustic
insulation. Divinycell H is compatible with virtually all commonly
used resin and manufacturing systems.
HIGH PERFORMANCE IPN CORE MATERIAL
Low water absorption
Superior damage tolerance
Fast and easy to process
Good chemical resistance
Excellent fatigue properties
Low resin uptake
Wide range of properties
Provides excellent mechanical properties to a low weight
PRODUCT CHARACTERISTICS
diabgroup.com
MECHANICAL PROPERTIES DIVINYCELL
H
Property Test Pr ocedure Unit H45 H60 H80 H100 H130 H160 H200 H250
Compressive
Strength
1 ASTM D 1621 MPa
Nominal 0.6 0.9 1.4 2.0 3.0 3.4 5.4 7. 2
Minimum 0.5 0.7 1.15 1.65 2.4 2.8 4.5 6.1
Compressive Modulus
1
A S T M D1621-B-7 3MPa
Nominal 50 70 90 135 170 200 310 400
Minimum 45 60 80 115 145 175 265 350
Tensile Strength
1
ASTM D 1623 MPa
Nominal 1.4 1.8 2.5 3.5 4.8 5.4 7. 1 9.2
Minimum 1.1 1.5 2.2 2.5 3.5 4.0 6.3 8.0
Tensile Modulus
1
ASTM D 1623 MPa
Nominal 55 75 95 130 175 205 250 320
Minimum 45 57 85 105 135 160 210 260
Shear Strength ASTM C 273 MPa
Nominal 0.56 0.76 1.15 1.6 2.2 2.6 3.5 4.5
Minimum 0.46 0.63 0.95 1.4 1.9 2.2 3.2 3.9
Shear Modulus ASTM C 273 MPa
Nominal 15 20 27 35 50 60 73 97
Minimum 12 16 23 28 40 50 65 81
Shear Strain ASTM C 273 % Nominal 12 20 30 40 40 40 45 45
Density ISO 845 kg/m
3
Nominal 48 60 80 100 130 160 200 250
All values measured at +23 C
1. Properties measured perpendicular to the plane
Nominal value is an average value of a mechanical property at a nominal density
Minimum value is a minimum guaranteed mechanical property a material has
independently of density
TECHNICAL DATA
Divinycell H
Continuous operating temperature is typically -200 C to +70 C. The foam can be used in sandwich structures, for outdoor exposure, with external skin tempera-
tures up to +85 C. For optimal design of applications used in high operating temperatures in combination with continuous load, please contact Diab Technical
Services for detailed design instructions.
Maximum processing temperature is dependent on time, pressure and process conditions. Therefore users are advised to contact Diab Technical Services to
confirm that Divinycell H is compatible with their particular processing parameters.
Disclaimer:
This data sheet may be subject to revision and changes due to development
and changes of the material. The data is derived from tests and experience. If
not stated as minimum values, the data is average data and should be treated
as such. Calculations should be verified by actual tests. The data is furnished
without liability for the company and does not constitute a warranty or repre-
sentation in respect of the material or its use. The company reserves the right
to release new data sheets in replacement.
All content in this publication is protected by international copyright laws.
Copyright Diab July 2018.
Diab Group
Drottninggatan 7, 5th floor
SE-252 21 Helsingborg, Sweden
Tel +46 (0) 430 163 00
E-mail: info@diabgroup.com
Datasheet Diab Divinycell H rev19 SI June 2020
TECHNICAL CHARACTERISTICS DIVINYCELL
H
PHYSICAL CHARACTERISTICS DIVINYCELL
H
Characteristics
1
Unit H45 H60 H80 H100 H130 H160 H200 H250 Test method
Density variation % 10 10 10 10 10 10 10 10 –
Thermal conductivity
2
W/(m-K)0.028 0.029 0.031 0.033 0.036 0.040 0.044 0.049 EN 12667
Coeff, linear heat expansion x10
-6
/ C 40 40 40 40 40 40 40 40 ISO 4897
Heat Distortion Temperature C +1 2 5+1 2 5+1 2 5+1 2 5+1 2 5+1 2 5+1 2 5+1 2 5 DIN 53424
Continous temp range C – 2 0 0 /+7 0- 2 0 0 /+7 0- 2 0 0 /+7 0- 2 0 0 /+7 0- 2 0 0 /+7 0- 2 0 0 /+7 0- 2 0 0 /+7 0- 2 0 0 /+7 0-
Max process temp C +90 +90 +90 +1 10 +1 10 +1 10 +1 10 +1 10 –
Dissipation factor – 0.00020.00030.00050.00060.00090.00120.00150.0019 ASTM D 2520
Dielectric constant – 1.05 1.06 1.09 1.11 1.15 1.18 1.23 1.29 ASTM D 2520
Poissons ratio
3
– 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 D638-08
Format Unit H45 H60 H80 H100 H130H160 H200 H250
Plain sheets
Lengthmm 2440 2440 2440 21601960 1860 1730 1640
Width mm 1220 1220 1220 1070 970 915 850 800
GS sheet
Lengthmm 1220 1220 12201080 980 930 865 –
Width mm 813 813 813 1070 970 915 850 –
GS sheet
Lengthmm 1220 1220 1220 – – – – –
Width mm 1220 1220 1220 – – – – –
1. Typical values
2. Thermal conductivity at +20 C
3. Standard deviation is 0.045
TECHNICAL CHARACTERISTICS
Divinycell H is type approved by: