RTM AND COLD MOLDING RESIN
Unsaturated Polyester Resin
Liquid.
SAFETY DATA SHEET
GHS product identifier
Other means of identification
Product type
Emergency telephone
number (with hours of
operation)
Section 1. Identification
:
:
:
:
Supplier’s details :INTERPLASTIC CORPORATION
1225 Willow Lake Boulevard
St. Paul, MN 55110-5145
651.481.6860
RTM AND COLD MOLDING RESIN
Relevant identified uses of the substance or mixture and uses advised against
Product code :SIL44BA-2840A
Industrial applications.
CHEMTREC 24-Hour Emergency Telephone
US and Canada 800.424.9300
Outside US and Canada +1 703.741.5970
Section 2. Hazards identification
FLAMMABLE LIQUIDS – Category 3
ACUTE TOXICITY (inhalation) – Category 4
SKIN IRRITATION – Category 2
EYE IRRITATION – Category 2A
CARCINOGENICITY – Category 2
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Respiratory tract
irritation) – Category 3
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) (hearing organs) –
Category 1
Classification of the
substance or mixture
:
Signal word :Danger
Hazard statements :Flammable liquid and vapor.
Harmful if inhaled.
Causes serious eye irritation.
Causes skin irritation.
Suspected of causing cancer.
May cause respiratory irritation.
Causes damage to organs through prolonged or repeated exposure. (hearing organs)
Hazard pictograms :
Precautionary statements
GHS label elements
Percentage of the mixture consisting of ingredient(s) of unknown dermal toxicity: 51.2%
OSHA/HCS status :This material is considered hazardous by the OSHA Hazard Communication Standard
(29 CFR 1910.1200).
Date of issue/Date of revision :9/6/2018 Date of previous issue :No previous validationVersion:1 1/15
RTM AND COLD MOLDING RESIN SIL44BA-2840A
Section 2. Hazards identification
Prevention :Obtain special instructions before use. Do not handle until all safety precautions have
been read and understood. Wear protective gloves. Wear eye or face protection.
Wear protective clothing. Keep away from heat, hot surfaces, sparks, open flames and
other ignition sources. No smoking. Use explosion-proof electrical, ventilating, lighting
and all material-handling equipment. Use only non-sparking tools. Take precautionary
measures against static discharge. Keep container tightly closed. Use only outdoors or
in a well-ventilated area. Do not breathe vapor. Do not eat, drink or smoke when using
this product. Wash hands thoroughly after handling.
Response :Get medical attention if you feel unwell. IF exposed or concerned: Get medical
attention. IF INHALED: Remove person to fresh air and keep comfortable for breathing.
Call a POISON CENTER or physician if you feel unwell. IF ON SKIN (or hair): Take off
immediately all contaminated clothing. Rinse skin with water or shower. IF ON SKIN:
Wash with plenty of soap and water. Take off contaminated clothing and wash it before
reuse. If skin irritation occurs: Get medical attention. IF IN EYES: Rinse cautiously
with water for several minutes. Remove contact lenses, if present and easy to do.
Continue rinsing. If eye irritation persists: Get medical attention.
Storage :Store in a well-ventilated place. Keep cool. Store containers in a safe place.
Disposal :Dispose of contents and container in accordance with all local, regional, national and
international regulations. Do not pressurize, cut, weld, braze, solder, drill, grind or
expose containers to heat or sources of ignition.
Hazards not otherwise
classified
:None known.
Section 3. Composition/information on ingredients
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health or the environment and hence require reporting
in this section.
Other means of
identification
:Unsaturated Polyester Resin
Substance/mixture :
Occupational exposure limits, if available, are listed in Section 8.
Mixture
Any concentration shown as a range is to protect confidentiality or is due to batch variation.
Any concentration shown as exact is based on formula.
VOC content is listed in Section 9.
Environmental composition is shown in Section 15.
styrene <= 52.0 100-42-5
N,N-dimethylaniline <= 1.0 121-69-7
Ingredient name % CAS number
Section 4. First aid measures
Eye contact :
Description of necessary first aid measures
Immediately flush eyes with plenty of water, occasionally lifting the upper and lower
eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10
minutes. Get medical attention. Buffered baby shampoo will aid in removal of resin.
Date of issue/Date of revision :9/6/2018 Date of previous issue :No previous validationVersion:1 2/15
RTM AND COLD MOLDING RESIN SIL44BA-2840A
Section 4. First aid measures
Wash out mouth with water. Remove dentures if any. Remove victim to fresh air and
keep at rest in a position comfortable for breathing. If material has been swallowed and
the exposed person is conscious, give small quantities of water to drink. Stop if the
exposed person feels sick as vomiting may be dangerous. Do not induce vomiting
unless directed to do so by medical personnel. If vomiting occurs, the head should be
kept low so that vomit does not enter the lungs. Get medical attention. Never give
anything by mouth to an unconscious person. If unconscious, place in recovery position
and get medical attention immediately. Maintain an open airway. Loosen tight clothing
such as a collar, tie, belt or waistband.
Flush contaminated skin with plenty of water. Remove contaminated clothing and
shoes. Continue to rinse for at least 10 minutes. Get medical attention. Wash clothing
before reuse. Clean shoes thoroughly before reuse.
Remove victim to fresh air and keep at rest in a position comfortable for breathing. If it
is suspected that fumes are still present, the rescuer should wear an appropriate mask
or self-contained breathing apparatus. If not breathing, if breathing is irregular or if
respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It
may be dangerous to the person providing aid to give mouth-to-mouth resuscitation.
Get medical attention. If necessary, call a poison center or physician. If unconscious,
place in recovery position and get medical attention immediately. Maintain an open
airway. Loosen tight clothing such as a collar, tie, belt or waistband.
Skin contact
Inhalation
Ingestion :
:
:
Protection of first-aiders:No action shall be taken involving any personal risk or without suitable training. If it is
suspected that fumes are still present, the rescuer should wear an appropriate mask or
self-contained breathing apparatus. It may be dangerous to the person providing aid to
give mouth-to-mouth resuscitation.
Notes to physician :Treat symptomatically. Contact poison treatment specialist immediately if large
quantities have been ingested or inhaled.
Specific treatments :No specific treatment.
Most important symptoms/effects, acute and delayed
Inhalation :Harmful if inhaled. May cause respiratory irritation.
No known significant effects or critical hazards.:Ingestion
Skin contact :Causes skin irritation.
Causes serious eye irritation.:Eye contact
Over-exposure signs/symptoms
Skin contact
Ingestion
Inhalation Adverse symptoms may include the following:
respiratory tract irritation
coughing
No specific data.
Adverse symptoms may include the following:
irritation
redness
:
:
:
Eye contact :Adverse symptoms may include the following:
pain or irritation
watering
redness
Potential acute health effects
See toxicological information (Section 11)
Indication of immediate medical attention and special treatment needed, if necessary
Date of issue/Date of revision :9/6/2018 Date of previous issue :No previous validationVersion:1 3/15
RTM AND COLD MOLDING RESIN SIL44BA-2840A
Section 5. Fire-fighting measures
Promptly isolate the scene by removing all persons from the vicinity of the incident if
there is a fire. No action shall be taken involving any personal risk or without suitable
training. Move containers from fire area if this can be done without risk. Use water
spray to keep fire-exposed containers cool.
Hazardous thermal
decomposition products
Specific hazards arising
from the chemical
Decomposition products may include the following materials:
carbon dioxide
carbon monoxide
Flammable liquid and vapor. Runoff to sewer may create fire or explosion hazard. In a
fire or if heated, a pressure increase will occur and the container may burst, with the risk
of a subsequent explosion. The vapor/gas is heavier than air and will spread along the
ground. Vapors may accumulate in low or confined areas or travel a considerable
distance to a source of ignition and flash back.
Fire-fighters should wear appropriate protective equipment and self-contained breathing
apparatus (SCBA) with a full face-piece operated in positive pressure mode.
Special protective
equipment for fire-fighters
Use dry chemical, CO , water spray (fog) or foam.
Extinguishing media
:
:
:
Do not use water jet.
Suitable extinguishing
media
:
Unsuitable extinguishing
media
:
Special protective actions
for fire-fighters
:
Section 6. Accidental release measures
Environmental precautions
Personal precautions, protective equipment and emergency procedures
:
:No action shall be taken involving any personal risk or without suitable training.
Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilled material. Shut off all ignition sources.
No flares, smoking or flames in hazard area. Avoid breathing vapor or mist. Provide
adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put
on appropriate personal protective equipment.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air).
Large spill :
Small spill :
Methods and materials for containment and cleaning up
For non-emergency
personnel
For emergency responders:If specialized clothing is required to deal with the spillage, take note of any information in
Section 8 on suitable and unsuitable materials. See also the information in "For non-
emergency personnel".
Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Approach release from upwind. Prevent entry into sewers,
water courses, basements or confined areas. Contain and collect spillage with non-
combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and
place in container for disposal according to local regulations (see Section 13). Dispose
of via a licensed waste disposal contractor. Contaminated absorbent material may pose
the same hazard as the spilled product. Note: see Section 1 for emergency contact
information and Section 13 for waste disposal. Wear appropriate respiratory protection.
Wear protective clothing and eye or face protection:
Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Dispose of via a licensed waste disposal contractor.
Absorb with an inert material and transfer the spilled material and absorbent to an
appropriate waste disposal container. Wear appropriate respirator when ventilation is
inadequate. Wear eye/face protection.
Date of issue/Date of revision :9/6/2018 Date of previous issue :No previous validationVersion:1 4/15
RTM AND COLD MOLDING RESIN SIL44BA-2840A
Section 7. Handling and storage
Advice on general
occupational hygiene
Conditions for safe storage,
including any
incompatibilities
Eating, drinking and smoking should be prohibited in areas where this material is
handled, stored and processed. Workers should wash hands and face before eating,
drinking and smoking. Remove contaminated clothing and protective equipment before
entering eating areas. See also Section 8 for additional information on hygiene
measures.
Do not store above the following temperature: 38 C (100.4 F). Store in accordance with
local regulations. Store in a segregated and approved area. Store in original container
protected from direct sunlight in a dry, cool and well-ventilated area, away from
incompatible materials (see Section 10) and food and drink. Eliminate all ignition
sources. Separate from oxidizing materials. Keep container tightly closed and sealed
until ready for use. Containers that have been opened must be carefully resealed and
kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate
containment to avoid environmental contamination. See Section 10 for incompatible
materials before handling or use. Store containers in a safe place.
:
:
Protective measures Put on appropriate personal protective equipment (see Section 8). Avoid exposure -
obtain special instructions before use. Do not handle until all safety precautions have
been read and understood. Do not get in eyes or on skin or clothing. Do not breathe
vapor or mist. Do not ingest. Use only with adequate ventilation. Wear appropriate
respirator when ventilation is inadequate. Do not enter storage areas and confined
spaces unless adequately ventilated. Keep in the original container or an approved
alternative made from a compatible material, kept tightly closed when not in use. Store
and use away from heat, sparks, open flame or any other ignition source. Use
explosion-proof electrical (ventilating, lighting and material handling) equipment. Use
only non-sparking tools. Take precautionary measures against electrostatic discharges.
Empty containers retain product residue and can be hazardous. Do not reuse container.
:
Precautions for safe handling
styrene ACGIH TLV (United States, 3/2017).
TWA: 20 ppm 8 hours.
TWA: 85 mg/m 8 hours.
STEL: 40 ppm 15 minutes.
STEL: 170 mg/m 15 minutes.
OSHA PEL 1989 (United States, 3/1989).
TWA: 50 ppm 8 hours.
TWA: 215 mg/m 8 hours.
STEL: 100 ppm 15 minutes.
STEL: 425 mg/m 15 minutes.
OSHA PEL Z2 (United States, 2/2013).
TWA: 100 ppm 8 hours.
CEIL: 200 ppm
AMP: 600 ppm 5 minutes.
NIOSH REL (United States, 10/2016).
TWA: 50 ppm 10 hours.
TWA: 215 mg/m 10 hours.
STEL: 100 ppm 15 minutes.
STEL: 425 mg/m 15 minutes.
N,N-dimethylaniline ACGIH TLV (United States, 3/2017). Absorbed through skin.
TWA: 5 ppm 8 hours.
TWA: 25 mg/m 8 hours.
STEL: 10 ppm 15 minutes.
Section 8. Exposure controls/personal protection
Ingredient name Exposure limits
Control parameters
Occupational exposure limits
Date of issue/Date of revision :9/6/2018 Date of previous issue :No previous validationVersion:1 5/15
RTM AND COLD MOLDING RESIN SIL44BA-2840A
Section 8. Exposure controls/personal protection
STEL: 50 mg/m 15 minutes.
OSHA PEL 1989 (United States, 3/1989). Absorbed through skin.
TWA: 5 ppm 8 hours.
TWA: 25 mg/m 8 hours.
STEL: 10 ppm 15 minutes.
STEL: 50 mg/m 15 minutes.
NIOSH REL (United States, 10/2016). Absorbed through skin.
TWA: 5 ppm 10 hours.
TWA: 25 mg/m 10 hours.
STEL: 10 ppm 15 minutes.
STEL: 50 mg/m 15 minutes.
OSHA PEL (United States, 6/2016). Absorbed through skin.
TWA: 5 ppm 8 hours.
TWA: 25 mg/m 8 hours.
Hand protection Chemical-resistant, impervious gloves complying with an approved standard should be
worn at all times when handling chemical products if a risk assessment indicates this is
necessary. Considering the parameters specified by the glove manufacturer, check
during use that the gloves are still retaining their protective properties. It should be
noted that the time to breakthrough for any glove material may be different for different
glove manufacturers. In the case of mixtures, consisting of several substances, the
protection time of the gloves cannot be accurately estimated.
Safety eyewear complying with an approved standard should be used when a risk
assessment indicates this is necessary to avoid exposure to liquid splashes, mists,
gases or dusts. If contact is possible, the following protection should be worn, unless
the assessment indicates a higher degree of protection: chemical splash goggles.
Eye/face protection
:
:
Body protection Personal protective equipment for the body should be selected based on the task being
performed and the risks involved and should be approved by a specialist before
handling this product. When there is a risk of ignition from static electricity, wear anti-
static protective clothing. For the greatest protection from static discharges, clothing
should include anti-static overalls, boots and gloves.
:
Environmental exposure
controls
:Emissions from ventilation or work process equipment should be checked to ensure
they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process equipment
will be necessary to reduce emissions to acceptable levels.
Appropriate engineering
controls
:Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or
other engineering controls to keep worker exposure to airborne contaminants below any
recommended or statutory limits. The engineering controls also need to keep gas,
vapor or dust concentrations below any lower explosive limits. Use explosion-proof
ventilation equipment.
Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Wash contaminated clothing before reusing. Ensure that eyewash stations and safety
showers are close to the workstation location.
Hygiene measures :
Individual protection measures
Skin protection
Other skin protection :Appropriate footwear and any additional skin protection measures should be selected
based on the task being performed and the risks involved and should be approved by a
specialist before handling this product.
Date of issue/Date of revision :9/6/2018 Date of previous issue :No previous validationVersion:1 6/15
RTM AND COLD MOLDING RESIN SIL44BA-2840A
Section 8. Exposure controls/personal protection
Based on the hazard and potential for exposure, select a respirator that meets the
appropriate standard or certification. Respirators must be used according to a
respiratory protection program to ensure proper fitting, training, and other important
aspects of use.
Respiratory protection :
Section 9. Physical and chemical properties
Physical state
Melting point
Vapor pressure
Relative density
Vapor density
Solubility
Liquid. [Liquid.]
Not available.
0.9 to 1.3
3.6 [Air = 1]
0.67 kPa (5 mm Hg) [room temperature]
Not available.
Sweetish.Odor
pH
Brownish-red.Color
Evaporation rate <1 (butyl acetate = 1)
Auto-ignition temperature
Flash point
Not available.
Closed cup: 31 C (87.8 F)
Not available.
Not applicable.
Viscosity Not available.
0.1 ppmOdor threshold
Partition coefficient: n-
octanol/water
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Appearance
Boiling point :145 C (293 F)
Lower and upper explosive
(flammable) limits
:Lower: 0.9%
Upper: 6.8%
Solubility in water :Not applicable.
VOC content :51.7 % (w/w) As shipped, including monomers and additives.
Section 10. Stability and reactivity
Conditions to avoid Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld,
braze, solder, drill, grind or expose containers to heat or sources of ignition. Do not
allow vapor to accumulate in low or confined areas.
The product is stable.Chemical stability
Reactive or incompatible with the following materials:
oxidizing materials
:
:
Incompatible materials :
Possibility of hazardous
reactions
:Hazardous reactions or instability may occur under certain conditions of storage or use.
Reactivity :No specific test data related to reactivity available for this product or its ingredients.
Hazardous polymerization may occur under certain conditions of storage or use. Keep
away from heat and direct sunlight. Keep away from heat and flame. Keep away from
oxidizing agents.
Reactive or incompatible with the following materials: metals, acids and alkalis.
Incompatible with alkali metals. Incompatible with some alkalis. Incompatible with some
strong acids. Incompatible with copper alloys, brass.
Date of issue/Date of revision :9/6/2018 Date of previous issue :No previous validationVersion:1 7/15
RTM AND COLD MOLDING RESIN SIL44BA-2840A
Section 10. Stability and reactivity
Hazardous decomposition
products
Under normal conditions of storage and use, hazardous decomposition products should
not be produced.
:
Section 11. Toxicological information
Acute toxicity
styrene LC50 Inhalation Gas. Rat 2770 ppm 4 hours
LC50 Inhalation Vapor Rat 11800 mg/m 4 hours
LD50 Oral Rat 2650 mg/kg -
N,N-dimethylaniline LD50 Dermal Rabbit 1770 mg/kg -
LD50 Oral Rat 951 mg/kg -
Product/ingredient name Result Species Dose Exposure
Carcinogenicity
Not available.
Conclusion/Summary :
Mutagenicity
Not available.
Irritation/Corrosion
styrene Eyes - Mild irritant Human - 50 parts per
million
-
Eyes - Moderate irritantRabbit - 24 hours 100
milligrams
-
Eyes - Severe irritantRabbit - 100
milligrams
-
Skin - Mild irritant Rabbit - 500
milligrams
-
Skin - Moderate irritantRabbit - 100 Percent-
N,N-dimethylaniline Eyes - Moderate irritantRabbit - 24 hours 20
milligrams
-
Eyes - Moderate irritantRabbit - 20 milligrams-
Skin - Mild irritant Rabbit - 24 hours 500
milligrams
-
Skin - Mild irritant Rabbit - 500
milligrams
-
Product/ingredient name Result Score Exposure Observation
Sensitization
Not available.
Species
Information on toxicological effects
Classification
Styrene manufacturers have determined that the weight of evidence for the
carcinogenicity of this substance does not meet the criteria for classification.
Styrene is listed by IARC as a possible carcinogen to humans (Group 2B) based on
"limited evidence" in humans, "limited evidence" in animals and "other relevant data".
The United States NTP listed styrene as reasonably anticipated to be a human
carcinogen based on "limited evidence" from studies in humans, "sufficient evidence"
from studies in experimental animals, and supporting data on mechanisms of
carcinogenesis. The significance of these results for humans has not been established
through risk assessment.
Date of issue/Date of revision :9/6/2018 Date of previous issue :No previous validationVersion:1 8/15
RTM AND COLD MOLDING RESIN SIL44BA-2840A
Section 11. Toxicological information
Teratogenicity
Not available.
Reproductive toxicity
Not available.
Information on the likely
routes of exposure
Inhalation :Harmful if inhaled. May cause respiratory irritation.
No known significant effects or critical hazards.:Ingestion
Skin contact :Causes skin irritation.
Causes serious eye irritation.:Eye contact
Symptoms related to the physical, chemical and toxicological characteristics
Skin contact
Ingestion
Inhalation Adverse symptoms may include the following:
respiratory tract irritation
coughing
No specific data.
Adverse symptoms may include the following:
irritation
redness
:
:
:
Eye contact :Adverse symptoms may include the following:
pain or irritation
watering
redness
Delayed and immediate effects and also chronic effects from short and long term exposure
Specific target organ toxicity (single exposure)
Specific target organ toxicity (repeated exposure)
styrene Category 3 Not applicable.Respiratory tract
irritation
Name Category
Name Category
styrene Category 1 Inhalation hearing organs
Aspiration hazard
Name Result
styrene ASPIRATION HAZARD - Category 1
Route of
exposure
Target organs
Route of
exposure
Target organs
:Not available.
Potential acute health effects
Short term exposure
styrene - 2B Reasonably anticipated to be a human carcinogen.
N,N-dimethylaniline - 3 -
Product/ingredient name NTPIARCOSHA
A study of long term effects of workers exposed to styrene levels in the range of 25-35 ppm for an 8-hour TWA indicated
a possible mild hearing loss.
Date of issue/Date of revision :9/6/2018 Date of previous issue :No previous validationVersion:1 9/15
RTM AND COLD MOLDING RESIN SIL44BA-2840A
Section 11. Toxicological information
Not available.
Causes damage to organs through prolonged or repeated exposure.General :
Suspected of causing cancer. Risk of cancer depends on duration and level of
exposure.
Carcinogenicity :
No known significant effects or critical hazards.Mutagenicity :
No known significant effects or critical hazards.Teratogenicity :
Developmental effects :No known significant effects or critical hazards.
Fertility effects :No known significant effects or critical hazards.
Potential chronic health effects
Numerical measures of toxicity
Oral 5172.9 mg/kg
Inhalation (gases) 5407.1 ppm
Inhalation (vapors) 23.03 mg/l
Route ATE value
Acute toxicity estimates
Potential immediate
effects
:Not available.
Potential delayed effects:Not available.
Potential immediate
effects
:Not available.
Long term exposure
Potential delayed effects:Not available.
Section 12. Ecological information
Toxicity
styrene Acute EC50 1400 g/l Fresh water Algae - Pseudokirchneriella
subcapitata
72 hours
Acute EC50 720 g/l Fresh water Algae - Pseudokirchneriella
subcapitata
96 hours
Acute EC50 4700 g/l Fresh water Daphnia - Daphnia magna 48 hours
Acute LC50 52 mg/l Marine water Crustaceans - Artemia salina48 hours
Acute LC50 4020 g/l Fresh water Fish - Pimephales promelas 96 hours
Chronic NOEC 63 g/l Fresh water Algae - Pseudokirchneriella
subcapitata
96 hours
N,N-dimethylaniline Acute EC50 22000 g/l Fresh water Algae - Chlorella pyrenoidosa72 hours
Acute EC50 2.3 mg/l Fresh water Daphnia - Daphnia magna 48 hours
Acute LC50 52600 g/l Fresh water Fish - Pimephales promelas 96 hours
Chronic NOEC 14000 g/l Fresh waterAlgae - Chlorella pyrenoidosa72 hours
Product/ingredient name SpeciesResult Exposure
Persistence and degradability
styrene OECD 70 % - Readily - 28 days - -
Product/ingredient name Test DoseResult Inoculum
Date of issue/Date of revision :9/6/2018 Date of previous issue :No previous validationVersion:1 10/15
RTM AND COLD MOLDING RESIN SIL44BA-2840A
Section 12. Ecological information
LogPow BCF Potential
Bioaccumulative potential
Other adverse effects :No known significant effects or critical hazards.
Product/ingredient name
styrene 0.35 13.49 low
N,N-dimethylaniline 1.171 16 low
Product/ingredient name Aquatic half-life Photolysis Biodegradability
styrene - - Readily
Soil/water partition
coefficient (KOC)
:Not available.
Mobility in soil
Section 13. Disposal considerations
The generation of waste should be avoided or minimized wherever possible. Disposal
of this product, solutions and any by-products should at all times comply with the
requirements of environmental protection and waste disposal legislation and any
regional local authority requirements. Dispose of surplus and non-recyclable products
via a licensed waste disposal contractor. Waste should not be disposed of untreated to
the sewer unless fully compliant with the requirements of all authorities with jurisdiction.
Waste packaging should be recycled. Incineration or landfill should only be considered
when recycling is not feasible. This material and its container must be disposed of in a
safe way. Care should be taken when handling emptied containers that have not been
cleaned or rinsed out. Empty containers or liners may retain some product residues.
Vapor from product residues may create a highly flammable or explosive atmosphere
inside the container. Do not cut, weld or grind used containers unless they have been
cleaned thoroughly internally. Avoid dispersal of spilled material and runoff and contact
with soil, waterways, drains and sewers.
:Disposal methods
Section 14. Transport information
RESIN
SOLUTION
3
III
RESIN
SOLUTION
3
III
RESIN
SOLUTION
UN1866
3
III
UN1866 UN1866
DOT
Classification
IMDGIATA
UN number
UN proper
shipping name
Transport
hazard class(es)
Packing group
Additional information
Environmental
hazards
No. No.No.
Mexico
Classification
UN1866
RESIN
SOLUTION
3
III
No.
TDG
Classification
UN1866
RESIN
SOLUTION
3
III
No.
Date of issue/Date of revision :9/6/2018 Date of previous issue :No previous validationVersion:1 11/15
RTM AND COLD MOLDING RESIN SIL44BA-2840A
Section 14. Transport information
Reportable quantity 1952 lbs / 886.22 kg [212.83 gal / 805.65 L]. Package sizes
shipped in quantities less than the product reportable quantity are not subject to the RQ
(reportable quantity) transportation requirements.
Special precautions for user
Transport in bulk according
to Annex II of MARPOL and
the IBC Code
Transport within user s premises: always transport in closed containers that are
upright and secure. Ensure that persons transporting the product know what to do in the
event of an accident or spillage.
:Not available.
:
Product classified as per the following sections of the Transportation of Dangerous
Goods Regulations: 2.18-2.19 (Class 3).
DOT Classification
TDG Classification
:
:
Section 15. Regulatory information
U.S. Federal regulations
Clean Water Act (CWA) 307: ethylbenzene; Naphthenic acids, copper salts
Clean Water Act (CWA) 311: styrene; ethylbenzene; xylene
:
SARA 313
Clean Air Act Section 112
(b) Hazardous Air
Pollutants (HAPs)
:
Clean Air Act Section 602
Class I Substances
:Not listed
Clean Air Act Section 602
Class II Substances
:Not listed
TSCA 8(a) PAIR: Poly(oxy-1,2-ethanediyl), -[4-(1,1,3,3-tetramethylbutyl)phenyl]- -
hydroxy-; 4-tert-butylpyrocatechol; triethyl phosphate; N,N-dimethylaniline
TSCA 8(a) CDR Exempt/Partial exemption: Not determined
TSCA 8(c) calls for record of SAR: triethyl phosphate
SARA 302/304
SARA 304 RQ :400000 lbs / 181600 kg [43612.4 gal / 165090.9 L]
1,4-dihydroxybenzene <0.1 Yes.500 / 10000- 100 -
Composition/information on ingredients
Name % EHS(lbs) (lbs)(gallons) (gallons)
SARA 302 TPQ SARA 304 RQ
SARA 311/312
Classification :FLAMMABLE LIQUIDS - Category 3
ACUTE TOXICITY (inhalation) - Category 4
SKIN IRRITATION - Category 2
EYE IRRITATION - Category 2A
CARCINOGENICITY - Category 2
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Respiratory tract
irritation) - Category 3
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) (hearing organs) -
Category 1
Styrene
Cobalt Compounds
Ethyl benzene
Xylenes
Hydroquinone
N,N-Diethyl aniline
Glycol ethers
Quinone
Date of issue/Date of revision :9/6/2018 Date of previous issue :No previous validationVersion:1 12/15
RTM AND COLD MOLDING RESIN SIL44BA-2840A
Section 15. Regulatory information
The following components are listed: STYRENE; PHENYLETHYLENEMassachusetts :
Product name CAS number %
SARA 313 notifications must not be detached from the SDS and any copying and redistribution of the SDS shall include
copying and redistribution of the notice attached to copies of the SDS subsequently redistributed.
Styrene
Ethylbenzene
Form R - Reporting
requirements
Supplier notification
California Prop. 65
New York :The following components are listed: Styrene
New Jersey :The following components are listed: STYRENE MONOMER; BENZENE, ETHENYL-
Pennsylvania :The following components are listed: BENZENE, ETHENYL-
State regulations
Inventory list
Australia :All components are listed or exempted.
Canada :All components are listed or exempted.
China :All components are listed or exempted.
Europe :Not determined.
Japan :Japan inventory (ENCS): Not determined.
Japan inventory (ISHL): Not determined.
Republic of Korea :All components are listed or exempted.
Malaysia :Not determined.
New Zealand :All components are listed or exempted.
Philippines :Not determined.
Taiwan :All components are listed or exempted.
Turkey :Not determined.
United States :All components are listed or exempted.
Thailand :Not determined.
Viet Nam :Not determined.
:The following components are listed. For more information go to www.P65Warnings.ca.gov.
styrene 100-42-5 51.23
styrene 100-42-5 51.23
Any concentration shown as exact is based on formula.
Section 16. Other information
Hazardous Material Information System (U.S.A.)
2
3
1
*
Health
Flammability
Physical hazards
Caution: HMIS ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4
representing significant hazards or risks. Although HMIS ratings and the associated label are not required on
SDSs or products leaving a facility under 29 CFR 1910.1200, the preparer may choose to provide them. HMIS
ratings are to be used with a fully implemented HMIS program. HMIS is a registered trademark and service
mark of the American Coatings Association, Inc.
Date of issue/Date of revision :9/6/2018 Date of previous issue :No previous validationVersion:1 13/15
RTM AND COLD MOLDING RESIN SIL44BA-2840A
Section 16. Other information
9/6/2018
History
Date of printing
Date of issue/Date of
revision
Version
Prepared by
Date of previous issue
:
:
:
:
:
References :
Key to abbreviations :ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships, 1973
as modified by the Protocol of 1978. ("Marpol" = marine pollution)
UN = United Nations
9/6/2018
No previous validation
1
1
3
2
National Fire Protection Association (U.S.A.)
Health
Special
Instability/Reactivity
Flammability
The customer is responsible for determining the PPE code for this material. For more information on HMIS
Personal Protective Equipment (PPE) codes, consult the HMIS Implementation Manual.
Reprinted with permission from NFPA 704-2001, Identification of the Hazards of Materials for Emergency
Response Copyright 1997, National Fire Protection Association, Quincy, MA 02269. This reprinted material is
not the complete and official position of the National Fire Protection Association, on the referenced subject
which is represented only by the standard in its entirety.
Copyright 2001, National Fire Protection Association, Quincy, MA 02269. This warning system is intended to
be interpreted and applied only by properly trained individuals to identify fire, health and reactivity hazards of
chemicals. The user is referred to certain limited number of chemicals with recommended classifications in
NFPA 49 and NFPA 325, which would be used as a guideline only. Whether the chemicals are classified by NFPA
or not, anyone using the 704 systems to classify chemicals does so at their own risk.
Procedure used to derive the classification
Classification Justification
FLAMMABLE LIQUIDS - Category 3 On basis of test data
ACUTE TOXICITY (inhalation) - Category 4 Calculation method
SKIN IRRITATION - Category 2 Calculation method
EYE IRRITATION - Category 2A Calculation method
CARCINOGENICITY - Category 2 Calculation method
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Respiratory tract
irritation) - Category 3
Calculation method
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) (hearing organs) -
Category 1
Calculation method
Health, Safety and Environmental Department
For questions about the
SDS, contact
:iasafety@ip-corporation.com
29 CFR 1910.1200 Hazard Communication Standard, March 2012
CCR Title 27 Division 4 Office of Environmental Health Hazard Assessment (California
Prop. 65)
American Composites Manufacturers Association
Styrene Information and Research Center
New form 08-2018
Date of issue/Date of revision :9/6/2018 Date of previous issue :No previous validationVersion:1 14/15
RTM AND COLD MOLDING RESIN SIL44BA-2840A
Section 16. Other information
To the best of our knowledge, the information contained herein is accurate. However, neither the above-named
supplier, nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the
information contained herein.
Final determination of suitability of any material is the sole responsibility of the user. All materials may present
unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot
guarantee that these are the only hazards that exist.
Notice to reader
Indicates information that has changed from previously issued version.
Date of issue/Date of revision :9/6/2018 Date of previous issue :No previous validationVersion:1 15/15