Vacuum Infusion Resin
Unsaturated Polyester Resin
Liquid.
SAFETY DATA SHEET
GHS product identifier
Other means of identification
Product type
Emergency telephone
number (with hours of
operation)
Section 1. Identification
:
:
:
:
Supplier’s details :INTERPLASTIC CORPORATION
1225 Willow Lake Boulevard
St. Paul, MN 55110-5145
651.481.6860
Vacuum Infusion Resin
Relevant identified uses of the substance or mixture and uses advised against
Product code :COR45-220-389
Industrial applications.
CHEMTREC 24-Hour Emergency Telephone
US and Canada 800.424.9300
Outside US and Canada +1 703.741.5970
Section 2. Hazards identification
FLAMMABLE LIQUIDS – Category 3
ACUTE TOXICITY (inhalation) – Category 4
SKIN IRRITATION – Category 2
EYE IRRITATION – Category 2A
CARCINOGENICITY – Category 2
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Respiratory tract
irritation) – Category 3
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) – Category 1
Classification of the
substance or mixture
:
Signal word :Danger
Hazard statements :Flammable liquid and vapor.
Causes skin irritation.
Causes serious eye irritation.
Harmful if inhaled.
May cause respiratory irritation.
Suspected of causing cancer.
Causes damage to organs through prolonged or repeated exposure. (hearing organs)
Hazard pictograms :
Precautionary statements
GHS label elements
OSHA/HCS status :This material is considered hazardous by the OSHA Hazard Communication Standard
(29 CFR 1910.1200).
Date of issue/Date of revision :8/5/2024 Date of previous issue :11/1/2023 Version:3.01 1/13
Vacuum Infusion Resin COR45-220-389
Section 2. Hazards identification
Prevention :Obtain special instructions before use. Do not handle until all safety precautions have
been read and understood. Wear protective gloves, protective clothing and eye or face
protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition
sources. No smoking. Use explosion-proof electrical, ventilating or lighting equipment.
Use non-sparking tools. Take action to prevent static discharges. Use only outdoors or
in a well-ventilated area. Do not breathe vapor. Do not eat, drink or smoke when using
this product. Wash thoroughly after handling.
Response :IF exposed or concerned: Get medical advice or attention. IF INHALED: Remove
person to fresh air and keep comfortable for breathing. Call a POISON CENTER or
doctor if you feel unwell. IF ON SKIN (or hair): Take off immediately all contaminated
clothing. Rinse skin with water. IF ON SKIN: Wash with plenty of water. If skin irritation
occurs: Get medical advice or attention. IF IN EYES: Rinse cautiously with water for
several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If
eye irritation persists: Get medical advice or attention.
Storage :Store locked up. Store in a well-ventilated place. Keep container tightly closed. Keep
cool.
Disposal :Dispose of contents and container in accordance with all local, regional, national and
international regulations.
Hazards not otherwise
classified
:None known.
Section 3. Composition/information on ingredients
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health or the environment and hence require reporting
in this section.
Other means of
identification
:Unsaturated Polyester Resin
Substance/mixture :
Occupational exposure limits, if available, are listed in Section 8.
Mixture
Any concentration shown as a range is to protect confidentiality or is due to batch variation.
Any concentration shown as exact is based on formula.
VOC content is listed in Section 9.
Environmental composition is shown in Section 15.
styrene <= 37.0 100-42-5
N,N-dimethylaniline <= 1.0 121-69-7
Ingredient name % CAS number
Get medical attention.
Continue to rinse for at least 10 minutes. Get medical attention.
If it is suspected that fumes are still present, the rescuer should wear an appropriate
mask or self-contained breathing apparatus. It may be dangerous to the person
providing aid to give mouth-to-mouth resuscitation. Get medical attention. If necessary,
call a poison center or physician.
Section 4. First aid measures
Eye contact
Skin contact
Inhalation
Ingestion :
:
:
:
Description of necessary first aid measures
Most important symptoms/effects, acute and delayed
Get medical attention. Buffered baby shampoo will aid in removal of resin.
Date of issue/Date of revision :8/5/2024 Date of previous issue :11/1/2023 Version:3.01 2/13
Vacuum Infusion Resin COR45-220-389
Section 4. First aid measures
Protection of first-aiders:No action shall be taken involving any personal risk or without suitable training. If it is
suspected that fumes are still present, the rescuer should wear an appropriate mask or
self-contained breathing apparatus. It may be dangerous to the person providing aid to
give mouth-to-mouth resuscitation.
Notes to physician :Treat symptomatically. Contact poison treatment specialist immediately if large
quantities have been ingested or inhaled.
Specific treatments :No specific treatment.
Inhalation :Harmful if inhaled. May cause respiratory irritation.
No known significant effects or critical hazards.:Ingestion
Skin contact :Causes skin irritation.
Causes serious eye irritation.:Eye contact
Over-exposure signs/symptoms
Skin contact
Ingestion
Inhalation Adverse symptoms may include the following:
respiratory tract irritation
coughing
No specific data.
Adverse symptoms may include the following:
irritation
redness
:
:
:
Eye contact :Adverse symptoms may include the following:
pain or irritation
watering
redness
Potential acute health effects
See toxicological information (Section 11)
Indication of immediate medical attention and special treatment needed, if necessary
Section 5. Fire-fighting measures
Promptly isolate the scene by removing all persons from the vicinity of the incident if
there is a fire. No action shall be taken involving any personal risk or without suitable
training. Move containers from fire area if this can be done without risk. Use water
spray to keep fire-exposed containers cool.
Hazardous thermal
decomposition products
Specific hazards arising
from the chemical
Decomposition products may include the following materials:
carbon dioxide
carbon monoxide
halogenated compounds
Flammable liquid and vapor. Runoff to sewer may create fire or explosion hazard. In a
fire or if heated, a pressure increase will occur and the container may burst, with the risk
of a subsequent explosion.
Special protective
equipment for fire-fighters
Use an extinguishing agent suitable for the surrounding fire.
Extinguishing media
:
:
:
None known.
Suitable extinguishing
media
:
Unsuitable extinguishing
media
:
Special protective actions
for fire-fighters
:
Date of issue/Date of revision :8/5/2024 Date of previous issue :11/1/2023 Version:3.01 3/13
Vacuum Infusion Resin COR45-220-389
Section 6. Accidental release measures
Environmental precautions
Personal precautions, protective equipment and emergency procedures
:
:
No specific hazard.
Large spill :
Small spill :
Methods and materials for containment and cleaning up
For non-emergency
personnel
For emergency responders:If specialized clothing is required to deal with the spillage, take note of any information in
Section 8 on suitable and unsuitable materials. See also the information in "For non-
emergency personnel".
Note: see Section 1 for emergency contact information and Section 13 for waste
disposal.
Section 7. Handling and storage
Advice on general
occupational hygiene
Conditions for safe storage,
including any
incompatibilities
Workers should wash hands and face before eating, drinking and smoking. Remove
contaminated clothing and protective equipment before entering eating areas. See also
Section 8 for additional information on hygiene measures.
Do not store above the following temperature: 38 C (100.4 F). Store in accordance with
local regulations. Separate from oxidizing materials. See Section 10 for incompatible
materials before handling or use. Store containers in a safe place.
:
:
Protective measures Avoid exposure - obtain special instructions before use. Do not handle until all safety
precautions have been read and understood. Do not get in eyes or on skin or clothing.
Use only with adequate ventilation. Wear appropriate respirator when ventilation is
inadequate. Take precautionary measures against electrostatic discharges.
:
Precautions for safe handling
styrene ACGIH TLV (United States, 1/2023). Ototoxicant.
TWA: 10 ppm 8 hours.
STEL: 20 ppm 15 minutes.
OSHA PEL 1989 (United States, 3/1989).
TWA: 50 ppm 8 hours.
TWA: 215 mg/m 8 hours.
STEL: 100 ppm 15 minutes.
STEL: 425 mg/m 15 minutes.
OSHA PEL Z2 (United States, 2/2013).
TWA: 100 ppm 8 hours.
CEIL: 200 ppm
AMP: 600 ppm 5 minutes.
NIOSH REL (United States, 10/2020).
TWA: 50 ppm 10 hours.
TWA: 215 mg/m 10 hours.
STEL: 100 ppm 15 minutes.
STEL: 425 mg/m 15 minutes.
N,N-dimethylaniline ACGIH TLV (United States, 1/2023). Absorbed through skin.
Section 8. Exposure controls/personal protection
Ingredient name Exposure limits
Control parameters
Occupational exposure limits
Date of issue/Date of revision :8/5/2024 Date of previous issue :11/1/2023 Version:3.01 4/13
Vacuum Infusion Resin COR45-220-389
Section 8. Exposure controls/personal protection
TWA: 5 ppm 8 hours.
TWA: 25 mg/m 8 hours.
STEL: 10 ppm 15 minutes.
STEL: 50 mg/m 15 minutes.
OSHA PEL 1989 (United States, 3/1989). Absorbed through skin.
TWA: 5 ppm 8 hours.
TWA: 25 mg/m 8 hours.
STEL: 10 ppm 15 minutes.
STEL: 50 mg/m 15 minutes.
NIOSH REL (United States, 10/2020). Absorbed through skin.
TWA: 5 ppm 10 hours.
TWA: 25 mg/m 10 hours.
STEL: 10 ppm 15 minutes.
STEL: 50 mg/m 15 minutes.
OSHA PEL (United States, 5/2018). Absorbed through skin.
TWA: 5 ppm 8 hours.
TWA: 25 mg/m 8 hours.
Hand protection
Safety eyewear complying with an approved standard should be used when a risk
assessment indicates this is necessary to avoid exposure to liquid splashes, mists,
gases or dusts. If contact is possible, the following protection should be worn, unless
the assessment indicates a higher degree of protection: chemical splash goggles.
Eye/face protection
Respiratory protection :
:
:
Body protection Personal protective equipment for the body should be selected based on the task being
performed and the risks involved and should be approved by a specialist before
handling this product. When there is a risk of ignition from static electricity, wear anti-
static protective clothing. For the greatest protection from static discharges, clothing
should include anti-static overalls, boots and gloves.
:
Environmental exposure
controls
:Emissions from ventilation or work process equipment should be checked to ensure
they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process equipment
will be necessary to reduce emissions to acceptable levels.
Appropriate engineering
controls
:Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or
other engineering controls to keep worker exposure to airborne contaminants below any
recommended or statutory limits.
Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Wash contaminated clothing before reusing. Ensure that eyewash stations and safety
showers are close to the workstation location.
Hygiene measures :
Individual protection measures
Skin protection
Other skin protection :Appropriate footwear and any additional skin protection measures should be selected
based on the task being performed and the risks involved and should be approved by a
specialist before handling this product.
Date of issue/Date of revision :8/5/2024 Date of previous issue :11/1/2023 Version:3.01 5/13
Vacuum Infusion Resin COR45-220-389
Section 9. Physical and chemical properties
Physical state
Melting point
Vapor pressure
Relative density
Vapor density
Solubility
Liquid.
Not applicable.
0.9 to 1.3
3.6 [Air = 1]
0.67 kPa (5 mm Hg)
Not available.
Sweetish.Odor
pH
VariousColor
Evaporation rate <1 (butyl acetate = 1)
Auto-ignition temperature
Flash point
Not available.
Closed cup: 31.1 C (88 F)
Not applicable.
Not applicable.
Viscosity Not available.
0.1 ppmOdor threshold
Partition coefficient: n-
octanol/water
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Appearance
Boiling point :145 C (293 F)
Lower and upper explosive
(flammable) limits
:Lower: 0.9%
Upper: 6.8%
Solubility in water :Not applicable.
VOC content :37.2 % (w/w) As shipped, including monomers and additives.
Section 10. Stability and reactivity
Hazardous decomposition
products
Conditions to avoid No specific data.
Under normal conditions of storage and use, hazardous decomposition products should
not be produced.
The product is stable.Chemical stability
Reactive or incompatible with the following materials:
oxidizing materials
:
:
:
Incompatible materials :
Possibility of hazardous
reactions
:Hazardous reactions or instability may occur under certain conditions of storage or use.
Reactivity :No specific test data related to reactivity available for this product or its ingredients.
Hazardous polymerization may occur under certain conditions of storage or use.
Exothermic polymerization. Keep away from heat and direct sunlight. Keep away from
heat and flame. Keep away from oxidizing agents.
Reactive or incompatible with the following materials: metals, acids and alkalis.
Incompatible with alkali metals. Incompatible with some alkalis. Incompatible with some
strong acids. Incompatible with copper alloys, brass.
Date of issue/Date of revision :8/5/2024 Date of previous issue :11/1/2023 Version:3.01 6/13
Vacuum Infusion Resin COR45-220-389
Section 11. Toxicological information
Acute toxicity
styrene LC50 Inhalation Gas. Rat 2770 ppm 4 hours
LC50 Inhalation Vapor Rat 11800 mg/m 4 hours
LD50 Oral Rat 2650 mg/kg -
N,N-dimethylaniline LD50 Dermal Rabbit 1770 mg/kg -
LD50 Oral Rat 951 mg/kg -
Product/ingredient name Result Species Dose Exposure
Carcinogenicity
Not available.
Conclusion/Summary :
Mutagenicity
Not available.
Teratogenicity
Not available.
Reproductive toxicity
Not available.
Irritation/Corrosion
styrene Eyes - Mild irritant Human - 50 ppm -
Eyes - Moderate irritantRabbit - 24 hours 100
mg
-
Eyes - Severe irritantRabbit - 100 mg -
Skin - Mild irritant Rabbit - 500 mg -
Skin - Moderate irritantRabbit - 100 % -
N,N-dimethylaniline Eyes - Moderate irritantRabbit - 24 hours 20
mg
-
Eyes - Moderate irritantRabbit - 20 mg -
Skin - Mild irritant Rabbit - 24 hours 500
mg
-
Skin - Mild irritant Rabbit - 500 mg -
Product/ingredient name Result Score Exposure Observation
Sensitization
Not available.
Species
Specific target organ toxicity (single exposure)
Information on toxicological effects
Classification
styrene - 2A Reasonably anticipated to be a human carcinogen.
N,N-dimethylaniline - 3 -
Product/ingredient name NTPIARCOSHA
Styrene manufacturers have determined that the weight of evidence for the
carcinogenicity of this substance does not meet the criteria for classification.
In 2018, styrene was listed by IARC as a probable carcinogen to humans (Group 2A)
based on hazard assessment data. The United States NTP listed styrene as reasonably
anticipated to be a human carcinogen based on "limited evidence" from studies in
humans, "sufficient evidence" from studies in experimental animals, and supporting
data on mechanisms of carcinogenesis. The significance of these results for humans
has not been established through risk assessment.
Date of issue/Date of revision :8/5/2024 Date of previous issue :11/1/2023 Version:3.01 7/13
Vacuum Infusion Resin COR45-220-389
Section 11. Toxicological information
Not available.
Information on the likely
routes of exposure
Inhalation :Harmful if inhaled. May cause respiratory irritation.
No known significant effects or critical hazards.:Ingestion
Skin contact :Causes skin irritation.
Causes serious eye irritation.:Eye contact
Symptoms related to the physical, chemical and toxicological characteristics
Skin contact
Ingestion
Inhalation Adverse symptoms may include the following:
respiratory tract irritation
coughing
No specific data.
Adverse symptoms may include the following:
irritation
redness
:
:
:
Eye contact :Adverse symptoms may include the following:
pain or irritation
watering
redness
Potential chronic health effects
Delayed and immediate effects and also chronic effects from short and long term exposure
Specific target organ toxicity (repeated exposure)
styrene Category 3 - Respiratory tract
irritation
Name Category
Name Category
styrene Category 1 inhalation hearing organs
N,N-dimethylaniline Category 2 - -
Aspiration hazard
Name Result
styrene ASPIRATION HAZARD - Category 1
Route of
exposure
Target organs
Route of
exposure
Target organs
:Not available.
Potential acute health effects
Potential immediate
effects
:Not available.
Short term exposure
Potential delayed effects:Not available.
Potential immediate
effects
:Not available.
Long term exposure
Potential delayed effects:Not available.
A study of long term effects of workers exposed to styrene levels in the range of 25-35 ppm for an 8-hour TWA indicated
a possible mild hearing loss.
Date of issue/Date of revision :8/5/2024 Date of previous issue :11/1/2023 Version:3.01 8/13
Vacuum Infusion Resin COR45-220-389
Section 11. Toxicological information
Causes damage to organs through prolonged or repeated exposure.General :
Suspected of causing cancer. Risk of cancer depends on duration and level of
exposure.
Carcinogenicity :
No known significant effects or critical hazards.Mutagenicity :
No known significant effects or critical hazards.Teratogenicity :
Developmental effects :No known significant effects or critical hazards.
Fertility effects :No known significant effects or critical hazards.
Numerical measures of toxicity
Oral 7214.17 mg/kg
Inhalation (gases) 7540.85 ppm
Inhalation (vapors) 32.12 mg/l
Route ATE value
Acute toxicity estimates
Section 12. Ecological information
LogPow BCF Potential
Bioaccumulative potential
Other adverse effects :No known significant effects or critical hazards.
Product/ingredient name
styrene 0.35 13.49 low
N,N-dimethylaniline 1.171 16 low
Product/ingredient name Aquatic half-life Photolysis Biodegradability
styrene - - Readily
Toxicity
styrene Acute EC50 78000 g/l Marine waterAlgae - Skeletonema costatum96 hours
Acute EC50 4700 g/l Fresh water Daphnia - Daphnia magna 48 hours
Acute LC50 52 mg/l Marine water Crustaceans - Artemia salina48 hours
Acute LC50 4020 g/l Fresh water Fish - Pimephales promelas 96 hours
N,N-dimethylaniline Acute EC50 22000 g/l Fresh water Algae - Chlorella pyrenoidosa72 hours
Acute EC50 2.3 mg/l Fresh water Daphnia - Daphnia magna 48 hours
Acute LC50 52600 g/l Fresh water Fish - Pimephales promelas 96 hours
Chronic NOEC 14000 g/l Fresh waterAlgae - Chlorella pyrenoidosa72 hours
Product/ingredient name SpeciesResult Exposure
Persistence and degradability
styrene OECD 70 % - Readily - 28 days - -
Product/ingredient name Test DoseResult Inoculum
Soil/water partition
coefficient (KOC)
:Not available.
Mobility in soil
Date of issue/Date of revision :8/5/2024 Date of previous issue :11/1/2023 Version:3.01 9/13
Vacuum Infusion Resin COR45-220-389
Section 13. Disposal considerations
The generation of waste should be avoided or minimized wherever possible. Disposal
of this product, solutions and any by-products should at all times comply with the
requirements of environmental protection and waste disposal legislation and any
regional local authority requirements. Dispose of surplus and non-recyclable products
via a licensed waste disposal contractor. Waste should not be disposed of untreated to
the sewer unless fully compliant with the requirements of all authorities with jurisdiction.
Waste packaging should be recycled. Incineration or landfill should only be considered
when recycling is not feasible. This material and its container must be disposed of in a
safe way. Empty containers or liners may retain some product residues.
:Disposal methods
Section 14. Transport information
RESIN
SOLUTION
3
III
RESIN
SOLUTION
3
III
RESIN
SOLUTION
UN1866
3
III
UN1866 UN1866
Reportable quantity 2722.3 lbs / 1235.9 kg [296.82 gal / 1123.6 L]. Package sizes
shipped in quantities less than the product reportable quantity are not subject to the RQ
(reportable quantity) transportation requirements.
DOT
Classification
IMDGIATA
UN number
UN proper
shipping name
Transport
hazard class(es)
Packing group
Additional information
Environmental
hazards
Special precautions for user
Transport in bulk according
to IMO instruments
No. No.No.
Transport within user s premises: always transport in closed containers that are
upright and secure. Ensure that persons transporting the product know what to do in the
event of an accident or spillage.
:Not available.
:
Product classified as per the following sections of the Transportation of Dangerous
Goods Regulations: 2.18-2.19 (Class 3).
Mexico
Classification
UN1866
RESIN
SOLUTION
3
III
No.
DOT Classification
TDG Classification
:
:
TDG
Classification
UN1866
RESIN
SOLUTION
3
III
No.
Section 15. Regulatory information
U.S. Federal regulations
Clean Water Act (CWA) 307: Naphthenic acids, copper salts; 2-ethylhexanoic acid,
copper salt
Clean Water Act (CWA) 311: styrene; propionic acid
:
Clean Air Act Section 112(b)
Hazardous Air Pollutants
(HAPs)
:
TSCA 8(a) PAIR: N,N-dimethylaniline; triethyl phosphate
TSCA 8(a) CDR Exempt/Partial exemption: Not determined
TSCA 8(c) calls for record of SAR: triethyl phosphate
Listed
Date of issue/Date of revision :8/5/2024 Date of previous issue :11/1/2023 Version:3.01 10/13
Vacuum Infusion Resin COR45-220-389
Section 15. Regulatory information
The following components are listed: STYRENEMassachusetts :
SARA 313
Product name CAS number %
SARA 313 notifications must not be detached from the SDS and any copying and redistribution of the SDS shall include
copying and redistribution of the notice attached to copies of the SDS subsequently redistributed.
Styrene
Form R - Reporting
requirements
Supplier notification
California Prop. 65
Clean Air Act Section 602
Class I Substances
:Not listed
Clean Air Act Section 602
Class II Substances
:Not listed
New York :The following components are listed: Styrene
New Jersey :The following components are listed: STYRENE MONOMER
Pennsylvania :The following components are listed: BENZENE, ETHENYL-
State regulations
SARA 302/304
SARA 304 RQ :Not applicable.
No products were found.
Composition/information on ingredients
Inventory list
Australia :Not determined.
Canada :All components are listed or exempted.
China :All components are listed or exempted.
Europe :All components are listed or exempted.
Japan :Japan inventory (CSCL): Not determined.
Japan inventory (ISHL): Not determined.
Republic of Korea :All components are listed or exempted.
Malaysia :Not determined
New Zealand :All components are listed or exempted.
Philippines :Not determined.
SARA 311/312
Classification :FLAMMABLE LIQUIDS - Category 3
ACUTE TOXICITY (inhalation) - Category 4
SKIN IRRITATION - Category 2
EYE IRRITATION - Category 2A
CARCINOGENICITY - Category 2
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Respiratory tract irritation) -
Category 3
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) - Category 1
:The following components are listed. For more information go to www.P65Warnings.ca.gov.
styrene 100-42-5 <= 37.0
styrene 100-42-5 36.73
Any concentration shown as exact is based on formula.
If components are "Listed", and additional information is required, contact Supplier
using email in Section 16.
Date of issue/Date of revision :8/5/2024 Date of previous issue :11/1/2023 Version:3.01 11/13
Vacuum Infusion Resin COR45-220-389
Section 15. Regulatory information
Taiwan :All components are listed or exempted.
Turkey :Not determined.
United States :
Thailand :Not determined.
Viet Nam :All components are listed or exempted.
All components are active or exempted.
Section 16. Other information
8/5/2024
History
Date of printing
Date of issue/Date of
revision
:
:8/5/2024
Hazardous Material Information System (U.S.A.)
2
3
1
1
3
2
*
National Fire Protection Association (U.S.A.)
Health
Special
Instability/Reactivity
Flammability
Health
Flammability
Physical hazards
Caution: HMIS ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4
representing significant hazards or risks. Although HMIS ratings and the associated label are not required on
SDSs or products leaving a facility under 29 CFR 1910.1200, the preparer may choose to provide them. HMIS
ratings are to be used with a fully implemented HMIS program. HMIS is a registered trademark and service
mark of the American Coatings Association, Inc.
The customer is responsible for determining the PPE code for this material. For more information on HMIS
Personal Protective Equipment (PPE) codes, consult the HMIS Implementation Manual.
Reprinted with permission from NFPA 704-2001, Identification of the Hazards of Materials for Emergency
Response Copyright 1997, National Fire Protection Association, Quincy, MA 02269. This reprinted material is
not the complete and official position of the National Fire Protection Association, on the referenced subject
which is represented only by the standard in its entirety.
Copyright 2001, National Fire Protection Association, Quincy, MA 02269. This warning system is intended to
be interpreted and applied only by properly trained individuals to identify fire, health and reactivity hazards of
chemicals. The user is referred to certain limited number of chemicals with recommended classifications in
NFPA 49 and NFPA 325, which would be used as a guideline only. Whether the chemicals are classified by NFPA
or not, anyone using the 704 systems to classify chemicals does so at their own risk.
Procedure used to derive the classification
Classification Justification
FLAMMABLE LIQUIDS - Category 3 On basis of test data
ACUTE TOXICITY (inhalation) - Category 4 Calculation method
SKIN IRRITATION - Category 2 Calculation method
EYE IRRITATION - Category 2A Calculation method
CARCINOGENICITY - Category 2 Calculation method
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Respiratory tract
irritation) - Category 3
Calculation method
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) - Category 1 Calculation method
Date of issue/Date of revision :8/5/2024 Date of previous issue :11/1/2023 Version:3.01 12/13
Vacuum Infusion Resin COR45-220-389
Section 16. Other information
Version
Prepared by
To the best of our knowledge, the information contained herein is accurate. However, neither the above-named
supplier, nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the
information contained herein.
Final determination of suitability of any material is the sole responsibility of the user. All materials may present
unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot
guarantee that these are the only hazards that exist.
Notice to reader
Date of previous issue
:
:
:
Indicates information that has changed from previously issued version.
References :
Key to abbreviations :ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships, 1973
as modified by the Protocol of 1978. ("Marpol" = marine pollution)
UN = United Nations
11/1/2023
3.01
Health, Safety and Environmental Department
For questions about the
SDS, contact
:iasafety@ip-corporation.com
29 CFR 1910.1200 Hazard Communication Standard, March 2012
CCR Title 27 Division 4 Office of Environmental Health Hazard Assessment (California
Prop. 65)
American Composites Manufacturers Association
Styrene Information and Research Center
New form 08-2018
Date of issue/Date of revision :8/5/2024 Date of previous issue :11/1/2023 Version:3.01 13/13