Technical Safety Information Sheet (TSIS)
on a voluntary basis
according to EC 1907/2006
Page:1 of 4
TSIS – T 1777 C – T 1790 C – EN – 2022-10
F 02-18-05 V2 Layout: U. Blaha 12.09.2016 Released by: F. Milli 13.09.2016
Internal
Date of issue: 23.11.2016 Date of revision: 18.10.2 022 Version: 03
1. Product- and company identification
Product name : T 1777 C, T 1790 C
Company : Freudenberg Performance Materials SE & Co. KG
D-69465 Weinheim
Telephone : ++49 / 7631 / 71 – 0
Telefax : ++49 / 7631 / 73607
Information department : Product development
e-Mail address : steffen.traser@freudenberg-pm.com
Telephone : ++49 / 7631 / 71 – 293
Telefax : ++49 / 7631 / 71 – 293
2. Possible hazards No hazardous product under normal conditions.
Special hazard reference Accidental thermal decompo sition or melting state may cause
hazards.
3. Composition / information on ingredients
This document provides Material Safety Information (TSIS) for nonwovens on a voluntary basis. The TSIS is a
means of forwarding essential hazard information (including information on transport, handling, storage and
emergency actions) from the supplier of a nonwoven product to the recipient of this product. As nonwovens are
generally not hazardous, TSIS is not legally requested but must be considered as information. It is based on the
EC recommendation for MSDS (EC 1907/2006).
The information contained in this Material Safety Information Sheet has been compiled to the best of our
knowledge upon the explicit request of the customer. Therefore, the manufacturer does not assume any liability
with respect to the correctness and/or completeness of the information provided by this Material Safety Infor-
mation Sheet. The customer in particular shall not be released from his duty to check all safety-relevant proper-
ties of the delivered nonwovens, and to comply with the local official regulations.
Chemical nature (product)
Description : Wetlaid nonwoven, chemically bonded
Fibre type(s): C-Glass
Binder type(s): Polyacrylate
May contain : Fibre additives (e.g. spin finishes, delustrants, etc.)
Process auxiliaries (e.g. dispersing agents, defoamer, etc.)
Further information : None
4. First-aid measures
General advice : Under normal condition …
Inhalation : no specific measures to be taken
Skin contact : no specific measures to be taken
Eye contact : no specific measures to be taken
Ingestion : no specific measures to be taken
Information for the doctor :
5. Fire fighting measures
Suitable extinguishing media : All common extinguishi ng media (e.g. water, CO2, sand)
Unsuitable extinguishing media : None
Exposure hazards : Ref. to formation of flammable a nd toxic combustion products, as well
as skin contact with molten material, see pt. 10.
Ref. to disposal of unburned residues and contaminated
extinguishing media, see pt. 12.
Protective equipment for fire fighters : In event of fire it is advisable to wear a self-contained
Technical Safety Information Sheet (TSIS)
on a voluntary basis
according to EC 1907/2006
Page:2 of 4
TSIS – T 1777 C – T 1790 C – EN – 2022-10
F 02-18-05 V2 Layout: U. Blaha 12.09.2016 Released by: F. Milli 13.09.2016
Internal
breathing apparatus.
Further information : For flammable and toxic fumes as well as skin contact with molten
materials see 10.
6. Accidental release measures Not applicable
Personal precautions : No specific measures to be ta ken
Environmental precautions : No specific measures to be taken
Methods for cleaning : No specific measures to be t aken
Further information : No specific measures to be ta ken
7. Handling and storage Normal requirements
Handling : Ref. to exposure controls and personal p rotection in case of
mechanical-thermal treatment / processing, see pt. 8,
otherwise no specific measures to be taken.
Protection against fire and explosion : No specific measures to be taken
Storage : Storage : Storage under cool, dry and light- protected conditions is
recommended (storage temperature max. 40 C, avoidance of
high relative air humidity, formation of condensed water and
direct solar radiation).
8. Expose controls and personal protection No specific measures
Technical protective measure : During mechanical-th ermal processing (e.g. grinding, cutting, lamina-
ting), irritant (fibre) dusts and traces of irritant volatile components
may possibly be released. In these cases vacuum
equipment should be present or at least proper ventilation should
be implemented.
Exposure control limits : None
Personal protective equipment If (fibre) dusts are released in higher extent during mechanical
thermal processing, …
Respiratory protection : … the use of a respirato r is recommended, …
Hand protection : … wearing of protective gloves or at least the application of a
barrier cream is recommended, …
Eye protection : … wearing of safety glasses is re commended, …
Skin protection : … avoidance of intense skin contact is recommended, …
… otherwise no specific measures to be taken.
General safety and hygiene measures
Measures : Precautions similar to handling of chemic als are recommended.
9. Physical and chemical properties
Appearance : Roll good or cut sheet
Colour : White
Odour : Odourless
Changes in physical state
Boiling point/Boiling range ( C) : Not applicable
Melting point ( C) : Decomposition / Dissimilation (at least partially) above ca. 250 C
Freezing temperature ( C) : Not applicable
Flash point ( C) : Not easily inflammable
Ignition temperature ( C) : Not tested
Auto ignition : Not tested
Explosion hazard : Not liable to explode
Explosion limits (Vol.-%) : Not applicable
Vapour pressure (mbar) : Not applicable
Technical Safety Information Sheet (TSIS)
on a voluntary basis
according to EC 1907/2006
Page:3 of 4
TSIS – T 1777 C – T 1790 C – EN – 2022-10
F 02-18-05 V2 Layout: U. Blaha 12.09.2016 Released by: F. Milli 13.09.2016
Internal
Density (g/cm
3
) : ca. 0,1
Bulk density (kg/m
3
) : Not applicable
Solubility in water : Not tested (Product contains tr aces of water-soluble ingredients)
Solubility in other solvents : Binder system is solu ble in styrene
pH-value : Not applicable
Viscosity : Not applicable
Additional information : None
10. Stability and reactivity
Conditions to avoid : Under thermal decomposition f lammable and toxic fumes can be gen-
erated. Product may (at least partially) melt and / or decompose at
temperatures above ca. 250 C. Decomposition is enhanced resp. ac-
celerated in case of contact with below mentioned substances to
avoid.
Substances to avoid : Strong alkalis, strong (oxidizi ng) acids.
Hazardous decomposition products : Above 300 C toxic and flammable gases like carbon monoxide can be
released. The generation of decomposition and oxidation products is
subject to fire conditions. Non burned residues and water contamina-
tions after fire fighting should be disposed of in compliance with offi-
cial regulations.
Additional information : Molten material should not be contact by skin as it may adhere and
cause burns.
11. Toxicological information No toxic reaction known under normal conditions.
Acute toxicity : … not applicable / not known
Specific symptoms in animal experiments: … not applicable / not known
Irritation effects : … not applicable / not known
Sensitization : … not applicable / not known
Subacute to chronic toxicity : … not applicable / not known
Carcinogenicity, mutagenicity,
teratogenicity : … not applicable / not known
Information from practical experience : None
Additional information : No toxic reaction known und er normal conditions.
Note : Under decomposition conditions; toxic fumes and contaminated water,
see 10.
12. Ecological information
Biodegradability : Not biodegradable
Ecotoxicity : No ecotoxic effects are to be expected for regular transportation, stor-
age and duly use.
Further ecological information : For transportation , storage, normal use, no toxicological effect is
known. Possible water pollution, if components are washed out. In
event of fire, unburned residues as well as contaminated extinguish-
ing media must be disposed of in compliance with existing regula-
tions.
13. Disposal considerations
Product : Nonwovens can be disposed of as non-hazard ous solid waste, under
compliance with the local regulations.
Disposal code number :
AVV-Code : 040222
Technical Safety Information Sheet (TSIS)
on a voluntary basis
according to EC 1907/2006
Page:4 of 4
TSIS – T 1777 C – T 1790 C – EN – 2022-10
F 02-18-05 V2 Layout: U. Blaha 12.09.2016 Released by: F. Milli 13.09.2016
Internal
14. Transport information
Not classified as dangerous in the terms of transport regulations.
15. Regulatory information
Labelling according to EC-regulation : The product / is not required to be labelled according to EC regula-
tions.
National directives : Product is not subjected to sp ecial national regulations for duly use
(e.g. German chemicals act or direction on hazardous materials).
16. Other information None
The information contained herein is based on the present state of knowledge and does not therefore guarantee
certain properties. The technical safety information sheet only describes the products in aspect to their safety re-
quirements.
Recipients of our products must take on responsibility for observing existing laws and regulations.