Page 1/10
Safety Data Sheet
acc. to OSHA HCS
Printing date 06/07/2023 Reviewed on 09/08/2020
56.0.10
1 Identification
Product identifier
Trade name: MoldWiz INT-1888LE
Application of the substance / the mixture
Processing aid/ Additive
Release agent
Details of the supplier of the safety data sheet
Manufacturer/Supplier:
Axel Plastics Research Laboratories, Inc.
50 Cambridge Drive
Monroe, CT 06468 USA
info@axelplastics.com
Information department:Product safety department
Emergency telephone number:
USA and Canada: 1-800-424-9300 (24 hours)
Outside of USA and Canada: 001-703-527-3887 (24 hours)
2 Hazard(s) identification
Classification of the substance or mixture
The product is not classified as hazardous according to the Globally Harmonized System (GHS).
Label elements
GHS label elementsVoid
Hazard pictogramsVoid
Signal wordVoid
Hazard statementsVoid
Classification system:
NFPA ratings (scale 0 – 4)
0
1
0
Health = 0
Fire = 1
Reactivity = 0
HMIS-ratings (scale 0 – 4)
HEALTH
FIRE
REACTIVITY
0
1
0
Health = 0
Fire = 1
Reactivity = 0
Other hazards
Results of PBT and vPvB assessment
PBT:Not applicable.
vPvB:Not applicable.
3 Composition/information on ingredients
Chemical characterization: Mixtures
Description:Mixture of the substances listed below with nonhazardous additions.
Component Information:Void
US
(Contd. on page 2)
Page 2/10
Safety Data Sheet
acc. to OSHA HCS
Printing date 06/07/2023 Reviewed on 09/08/2020
Trade name: MoldWiz INT-1888LE
(Contd. of page 1)
56.0.10
4 First-aid measures
Description of first aid measures
General information:No special measures required.
After inhalation:Supply fresh air; consult doctor in case of complaints.
After skin contact:Generally the product does not irritate the skin.
After eye contact:Rinse opened eye for several minutes under running water.
After swallowing:If symptoms persist consult doctor.
Information for doctor:
Most important symptoms and effects, both acute and delayedNo further relevant information available.
Indication of any immediate medical attention and special treatment needed
No further relevant information available.
5 Fire-fighting measures
Extinguishing media
Suitable extinguishing agents:
Use fire fighting measures that suit the environment.
CO2, extinguishing powder or water spray. Fight larger fires with water spray or alcohol resistant foam.
Special hazards arising from the substance or mixtureNo further relevant information available.
Advice for firefighters
Protective equipment:No special measures required.
6 Accidental release measures
Personal precautions, protective equipment and emergency procedures
Wear protective equipment. Keep unprotected persons away.
Ensure adequate ventilation
No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Keep
unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Do not
breathe vapor or mist. Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate.
Put on appropriate personal protective equipment.
Environmental precautions:
Dilute with plenty of water.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the
relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air).
Do not allow to enter sewers/ surface or ground water.
Methods and material for containment and cleaning up:
Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust).
Small spill: Stop leak if without risk. Move containers from spill area. Dilute with water and mop up if water-
soluble. Alternatively, or if water-insoluble, absorb with an inert dry material and place in an appropriate waste
disposal container. Dispose of via a licensed waste disposal contractor.
Large spill: Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent
entry into sewers, water courses, basements or confined areas. Wash spillage into an effluent treatment plant or
proceed as follow. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth,
vermiculite or diatomaceous earth and place in container for disposal according to local regulations (see Section
13). Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same
hazard as the spilled product. Note: See Section 1 for emergency contact information and Section 13 for waste
disposal.
Reference to other sections
See Section 7 for information on safe handling.
See Section 8 for information on personal protection equipment.
(Contd. on page 3)
US
Page 3/10
Safety Data Sheet
acc. to OSHA HCS
Printing date 06/07/2023 Reviewed on 09/08/2020
Trade name: MoldWiz INT-1888LE
(Contd. of page 2)
56.0.10
See Section 13 for disposal information.
7 Handling and storage
Handling:
Precautions for safe handling
No special measures required.
Store in cool, dry place in tightly closed receptacles.
Put on appropriate personal protective equipment (see Section 8). Do not ingest. Avoid contact with eyes, skin and
clothing. Avoid breathing vapor or mist. Avoid release to the environment. Use only with adequate ventilation.
Wear appropriate respirator when ventilation is inadequate. Keep in the original container or an approved
alternative made from a compatible material, kept tightly closed when not in use. Empty containers retain product
residue and can be hazardous. Do not reuse container.
Information about protection against explosions and fires:No special measures required.
Conditions for safe storage, including any incompatibilities
Store in accordance with local regulations. Store in original container protected from direct sunlight in a dry, cool
and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Avoid freezing.
Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully
resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate containment to
avoid environmental contamination.
Storage:
Requirements to be met by storerooms and receptacles:No special requirements.
Information about storage in one common storage facility:Not required.
Further information about storage conditions:None.
Specific end use(s)No further relevant information available.
8 Exposure controls/personal protection
Additional information about design of technical systems:No further data; see item 7.
Control parameters
Components with limit values that require monitoring at the workplace:
The product does not contain any relevant quantities of materials with critical values that have to be monitored at
the workplace.
Additional information:The lists that were valid during the creation were used as basis.
Exposure controls
Personal protective equipment:
General protective and hygienic measures:
The usual precautionary measures for handling chemicals should be followed.
Breathing equipment:Not required.
Protection of hands:
Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/ the
chemical mixture.
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation.
Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation
Material of gloves
The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and
varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of
the glove material can not be calculated in advance and has therefore to be checked prior to the application.
Penetration time of glove material
The exact break through time has to be found out by the manufacturer of the protective gloves and has to be
observed.
(Contd. on page 4)
US
Page 4/10
Safety Data Sheet
acc. to OSHA HCS
Printing date 06/07/2023 Reviewed on 09/08/2020
Trade name: MoldWiz INT-1888LE
(Contd. of page 3)
56.0.10
Eye protection:Goggles recommended during refilling.
Body protection:Protective work clothing
* 9 Physical and chemical properties
Information on basic physical and chemical properties
General Information
Appearance:
Form: Fluid
Color: Amber colored
Odor: Mild
Odor threshold: Not determined.
pH-value: Not determined.
Change in condition
Melting point/Melting range: Undetermined.
Boiling point/Boiling range: Undetermined.
Flash Point: > 120 C (> 248 F)
Percentage Volatile To be determined
Decomposition temperature: Not determined.
Auto igniting: Product is not selfigniting.
Danger of explosion: Product does not present an explosion hazard.
Explosion limits:
Lower: Not determined.
Upper: Not determined.
Oxidizing properties Not determined.
Vapor pressure: Not determined.
Density: Not determined.
Relative density Not determined.
Vapor density Not determined.
Evaporation rate Not determined.
Solubility in / Miscibility with
Water: Fully miscible.
Partition coefficient (n-octanol/water):Not determined.
Viscosity:
Dynamic at 20 C (68 F): 400 600 mPas
Kinematic: Not determined.
Solvent separation test
VOC content: Not determined.
Other information No further relevant information available.
10 Stability and reactivity
ReactivityNo further relevant information available.
Chemical stabilityThe product is stable under recommended storage conditions.
(Contd. on page 5) US
Page 5/10
Safety Data Sheet
acc. to OSHA HCS
Printing date 06/07/2023 Reviewed on 09/08/2020
Trade name: MoldWiz INT-1888LE
(Contd. of page 4)
56.0.10
Thermal decomposition / conditions to be avoided:
No decomposition if used according to specifications.
Stable at ambient temperature.
Possibility of hazardous reactionsNo dangerous reactions known.
Conditions to avoidNo further relevant information available.
Incompatible materials:No further relevant information available.
Hazardous decomposition products:No dangerous decomposition products known.
11 Toxicological information
Information on toxicological effects
Acute toxicity:
Primary irritant effect:
on the skin:No irritant effect.
on the eye:No irritating effect.
Sensitization:No sensitizing effects known.
Additional toxicological information:
The product is not subject to classification according to internally approved calculation methods for preparations:
When used and handled according to specifications, the product does not have any harmful effects according to
our experience and the information provided to us.
Carcinogenic categories
IARC (International Agency for Research on Cancer)
None of the ingredients is listed.
NTP (National Toxicology Program)
None of the ingredients is listed.
OSHA-Ca (Occupational Safety & Health Administration)
None of the ingredients is listed.
IARC Monographs
Group 1: Carcinogenic to humans
Group 2A: Probably carcinogenic to humans
Group 2B: Possibly carcinogenic to humans
Group 3: Not classifiable as to its carcinogenicity to humans
Group 4: Probably not carcinogenic to humans
12 Ecological information
Toxicity
Aquatic toxicity:No further relevant information available.
Persistence and degradabilityNo further relevant information available.
Behavior in environmental systems:
Bioaccumulative potentialNo further relevant information available.
Mobility in soilNo further relevant information available.
Additional ecological information:
General notes:
Do not allow undiluted product or large quantities of it to reach ground water, water course or sewage system.
Results of PBT and vPvB assessment
PBT:Not applicable.
vPvB:Not applicable.
(Contd. on page 6)
US
Page 6/10
Safety Data Sheet
acc. to OSHA HCS
Printing date 06/07/2023 Reviewed on 09/08/2020
Trade name: MoldWiz INT-1888LE
(Contd. of page 5)
56.0.10
Other adverse effectsNo further relevant information available.
13 Disposal considerations
Waste treatment methods
Recommendation:
Smaller quantities can be disposed of with household waste.
The generation of waste should be avoided or minimized wherever possible. Disposal of this product, solutions
and any by-products should at all times comply with the requirements of environmental protection and waste
disposal legislation and any regional local authority requirements. Dispose of surplus and non-recyclable products
via a licensed waste disposal contractor. Waste should not be disposed of untreated to the sewer unless fully
compliant with the requirements of all authorities with jurisdiction.
The classification of the product may meet the criteria for a hazardous waste.
Uncleaned packagings:
Recommendation:
The generation of waste should be avoided or minimized wherever possible. Waste packaging should be recycled.
Incineration or landfill should only be considered when recycling is not feasible.
This material and its container must be disposed of in a safe way. Care should be taken when handling emptied
containers that have not been cleaned or rinsed out. Empty containers or liners may retain some product residues.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers.
Recommended cleansing agent:Water, if necessary with cleansing agents.
14 Transport information
UN-Number
DOT, ADN, IMDG, IATA not regulated
UN proper shipping name
DOT, ADN, IMDG, IATA not regulated
Transport hazard class(es)
DOT, ADN, IMDG, IATA
Class not regulated
Packing group
DOT, IMDG, IATA not regulated
Environmental hazards: Not applicable.
Special precautions for user Not applicable.
Transport in bulk according to Annex II of
MARPOL73/78 and the IBC Code Not applicable.
UN “Model Regulation”: not regulated
15 Regulatory information
Safety, health and environmental regulations/legislation specific for the substance or mixture
Sara
Section 313 (Specific toxic chemical listings):
None of the ingredients is listed.
(Contd. on page 7)
US
Page 7/10
Safety Data Sheet
acc. to OSHA HCS
Printing date 06/07/2023 Reviewed on 09/08/2020
Trade name: MoldWiz INT-1888LE
(Contd. of page 6)
56.0.10
TSCA (Toxic Substances Control Act):
All ingredients are listed.
Hazardous Air Pollutants
None of the ingredients is listed.
Proposition 65
Chemicals known to cause cancer:
None of the ingredients is listed.
Chemicals known to cause reproductive toxicity for females:
None of the ingredients is listed.
Chemicals known to cause reproductive toxicity for males:
None of the ingredients is listed.
Chemicals known to cause developmental toxicity:
None of the ingredients is listed.
US State Regulations
Connecticut – Hazardous Air Pollutants – HLVs (30 min)
None of the ingredients is listed.
Connecticut – Hazardous Air Pollutants – HLVs (8 hr)
None of the ingredients is listed.
Idaho – Non-Carcinogenic Toxic Air Pollutants – Emission Levels (ELs)
None of the ingredients is listed.
Idaho – Non-Carcinogenic Toxic Air Pollutants – Acceptable Ambient Concentrations
None of the ingredients is listed.
Occupational Exposure Limits – TWAs
None of the ingredients is listed.
Michigan – Occupational Exposure Limits – Skin Designations
None of the ingredients is listed.
Michigan – Occupational Exposure Limits – TWAs
None of the ingredients is listed.
Minnesota – Hazardous Substance List
None of the ingredients is listed.
Minnesota – Permissible Exposure Limits – Skin Designations
None of the ingredients is listed.
Minnesota – Permissible Exposure Limits – TWAs
None of the ingredients is listed.
New Hampshire – Regulated Toxic Air Pollutants – Ambient Air Levels (AALs) – 24-Hour
None of the ingredients is listed.
New Hampshire – Regulated Toxic Air Pollutants – Ambient Air Levels (AALs) – Annual
None of the ingredients is listed.
New York – Occupational Exposure Limits – Skin Designations
None of the ingredients is listed.
New York – Occupational Exposure Limits – TWAs
None of the ingredients is listed.
(Contd. on page 8)
US
Page 8/10
Safety Data Sheet
acc. to OSHA HCS
Printing date 06/07/2023 Reviewed on 09/08/2020
Trade name: MoldWiz INT-1888LE
(Contd. of page 7)
56.0.10
North Dakota – Air Pollutants – Guideline Concentrations – 1-Hour
None of the ingredients is listed.
North Dakota – Air Pollutants – Guideline Concentrations – 8-Hour
None of the ingredients is listed.
Oregon – Permissible Exposure Limits – TWAs
None of the ingredients is listed.
Tennessee – Occupational Exposure Limits – Skin Designations
None of the ingredients is listed.
Tennessee – Occupational Exposure Limits – TWAs
None of the ingredients is listed.
Texas – Effects Screening Levels – Long Term
None of the ingredients is listed.
Texas – Effects Screening Levels – Short Term
None of the ingredients is listed.
Vermont – Permissible Exposure Limits – Skin Designations
None of the ingredients is listed.
Vermont – Permissible Exposure Limits – TWAs
None of the ingredients is listed.
Washington – Permissible Exposure Limits – Skin Designations
None of the ingredients is listed.
Washington – Permissible Exposure Limits – STELs
None of the ingredients is listed.
Washington – Permissible Exposure Limits – TWAs
None of the ingredients is listed.
Wisconsin – Hazardous Air Contaminants – All Sources – Emissions From Stack Heights 25 Feet to Less
Than 40 Feet
None of the ingredients is listed.
Wisconsin – Hazardous Air Contaminants – All Sources – Emissions From Stack Heights 40 Feet to Less
Than 75 Feet
None of the ingredients is listed.
Wisconsin – Hazardous Air Contaminants – All Sources – Emissions From Stack Heights 75 Feet or Greater
None of the ingredients is listed.
Wisconsin – Hazardous Air Contaminants – All Sources – Emissions From Stack Heights Less Than 25 Feet
None of the ingredients is listed.
Carcinogenic categories
EPA (Environmental Protection Agency)
None of the ingredients is listed.
NIOSH-Ca (National Institute for Occupational Safety and Health)
None of the ingredients is listed.
EPA Carcinogen Category Key
EPA 2005 Guidelines:
CaH – Carcinogenic to humans.
L – Likely to be carcinogenic to humans.
SC – Suggestive evidence of carcinogenic potential.
II – Inadequate information to assess carcinogenic potential.
(Contd. on page 9)
US
Page 9/10
Safety Data Sheet
acc. to OSHA HCS
Printing date 06/07/2023 Reviewed on 09/08/2020
Trade name: MoldWiz INT-1888LE
(Contd. of page 8)
56.0.10
NL – Not likely to be carcinogenic to humans.
EPA 1999 Guidelines:
CaH – Carcinogenic to humans.
L – Likely to be carcinogenic to humans.
S – Suggestive evidence of carcinogenicity, but not sufficient to assess human carcinogenic potential.
I – Data are inadequate for an assessment of human carcinogenic potential.
NL – Not likely to be carcinogenic to humans.
EPA 1996 Guidelines:
K/L – Known/likely human carcinogen.
CBD – Carcinogenic potential cannot be determined.
NL – Not likely to be carcinogenic to humans.
EPA 1986 Guidelines:
A – Human carcinogen
B1 – Probable human carcinogen – based on limited evidence of carcinogenicity in humans and sufficient evidence
of carcinogenicity in animals.
B2 – Probable human carcinogen – based on sufficient evidence of carcinogenicity in animals.
C – Possible human carcinogen.
D – Not classifiable as to human carcinogenicity.
E – Evidence of non-carcinogenicity for humans.
GHS label elementsVoid
Hazard pictogramsVoid
Signal wordVoid
Hazard statementsVoid
National regulations:
The components of this product are listed on the Taiwan (TCSI) inventory.
The components of this product are listed on the USA (TSCA) inventory.
The components of this product are listed on the European (EINECS) inventory.
The components of this product are listed on the Canadian (DSL) inventory.
The components of this product are listed on the South Korean (KECI) inventory.
The components of this product are listed on the Chinese (IECSC) inventory.
The components of this product are listed on the Japan (ENCS) inventory.
Other regulations, limitations and prohibitive regulations
Substances of very high concern (SVHC) according to REACH, Article 57
None of the ingredients is listed.
Chemical safety assessment:A Chemical Safety Assessment has not been carried out.
16 Other information
Disclaimer: This data is offered in good faith as typical values and not as a product specification. No warranty,
either expressed or implied, is hereby made. The recommended industrial hygiene and safe handling procedures
are believed to be generally applicable. However, each user should review recommendations in the specific context
of the intended use and determine whether they are appropriate.
Procedure used to derive the classificationCalculation method.
Contact:info@axelplastics.com
Date of preparation / last revision06/07/2023
Abbreviations and acronyms:
IMDG: International Maritime Code for Dangerous Goods
DOT: US Department of Transportation
IATA: International Air Transport Association
EINECS: European Inventory of Existing Commercial Chemical Substances
(Contd. on page 10)
US
Page 10/10
Safety Data Sheet
acc. to OSHA HCS
Printing date 06/07/2023 Reviewed on 09/08/2020
Trade name: MoldWiz INT-1888LE
(Contd. of page 9)
56.0.10
ELINCS: European List of Notified Chemical Substances
CAS: Chemical Abstracts Service (division of the American Chemical Society)
NFPA: National Fire Protection Association (USA)
HMIS: Hazardous Materials Identification System (USA)
VOC: Volatile Organic Compounds (USA, EU)
PBT: Persistent, Bioaccumulative and Toxic
SVHC: Substances of Very High Concern
vPvB: very Persistent and very Bioaccumulative
NIOSH: National Institute for Occupational Safety
OSHA: Occupational Safety & Health
TLV: Threshold Limit Value
PEL: Permissible Exposure Limit
REL: Recommended Exposure Limit
* Data compared to the previous version altered.
US